NETGEAR Network Router XE103 User Manual

XEPS103 Space-  
Saving Powerline  
Network Extender  
NETGEAR, Inc.  
4500 Great America Parkway  
Santa Clara, CA 95054 USA  
202-10239-01  
February 2007  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
© 2007 by NETGEAR, Inc. All rights reserved. February 2007.  
Trademarks  
NETGEAR is a trademark of Netgear, Inc. Microsoft, Windows, and Windows NT are registered trademarks of  
Microsoft Corporation. Other brand and product names are registered trademarks or trademarks of their respective  
holders.  
Statement of Conditions  
In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to  
make changes to the products described in this document without notice. NETGEAR does not assume any liability that  
may occur due to the use or application of the product(s) or circuit layout(s) described herein.  
Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice  
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to  
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a  
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and  
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no  
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to  
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try  
to correct the interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
Bestätigung des Herstellers/Importeurs  
Es wird hiermit bestätigt, daß das XEPS103 Space-Saving Powerline Network Extender gemäß der im BMPT-  
AmtsblVfg 243/1991 und Vfg 46/1992 aufgeführten Bestimmungen entstört ist. Das vorschriftsmäßige Betreiben  
einiger Geräte (z.B. Testsender) kann jedoch gewissen Beschränkungen unterliegen. Lesen Sie dazu bitte die  
Anmerkungen in der Betriebsanleitung.  
Das Bundesamt für Zulassungen in der Telekommunikation wurde davon unterrichtet, daß dieses Gerät auf den Markt  
gebracht wurde und es ist berechtigt, die Serie auf die Erfüllung der Vorschriften hin zu überprüfen.  
Certificate of the Manufacturer/Importer  
It is hereby certified that the XEPS103 Space-Saving Powerline Network Extender has been suppressed in accordance  
with the conditions set out in the BMPT-AmtsblVfg 243/1991 and Vfg 46/1992. The operation of some equipment (for  
example, test transmitters) in accordance with the regulations may, however, be subject to certain restrictions. Please  
refer to the notes in the operating instructions.  
Federal Office for Telecommunications Approvals has been notified of the placing of this equipment on the market  
and has been granted the right to test the series for compliance with the regulations.  
iii  
v1.0, February 2007  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Product and Publication Details  
Model Number:  
XEPS103  
Publication Date:  
Product Family:  
February 2007  
Powerline extender  
Product Name:  
XEPS103 Space-Saving Powerline Network Extender  
Home or Business Product:  
Language:  
Home  
English  
Publication Part Number:  
202-10239-01  
Publication Version Number: 1.0  
Technical Support  
Please refer to the support information card that shipped with your product. By registering your  
product at http://www.netgear.com/register, we can provide you with faster expert technical  
support and timely notices of product and software upgrades.  
NETGEAR, INC. Support Information  
Phone: 1-888-NETGEAR, for US & Canada only. For other countries, see your Support  
information card.  
iv  
v1.0, February 2007  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
Install the XEPS103 PowerLine Encryption Utility  
(Highly Recommended) .....................................................................................................6  
i
v1.0, February 2007  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ii  
v1.0, February 2007  
Download from Www.Somanuals.com. All Manuals Search And Download.  
About This Manual  
The XEPS103 Space-Saving Powerline Network Extender User Guide describes how to install,  
configure, and troubleshoot the NETGEAR® XEPS103 Powerline Extender. The information in  
this manual is intended for readers with intermediate computer and Internet skills. For information  
about product features, see the NETGEAR website at http://www.netgear.com.  
Conventions, Formats, and Scope  
The conventions, formats, and scope of this manual are described in the following sections.  
Typographical conventions. This manual uses the following typographical conventions.  
Italics  
Emphasis, books, CDs, URL names  
Bold  
User input  
Screen text, file and server names, extensions, commands, IP addresses  
Monospace  
Formats. This manual uses the following formats to highlight special messages.  
Note: This format is used to highlight information of importance or special interest.  
Tip: This format is used to highlight a procedure that will save time or resources.  
Warning: Ignoring this type of note may result in a malfunction or damage to the  
equipment.  
Danger: This is a safety warning. Failure to take heed of this notice may result in  
personal injury or death.  
iii  
v1.0, February 2007  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
XEPS103 Space-Saving Powerline Network Extender User Guide  
Scope. This manual is written for the XEPS103 Powerline Extender according to these  
specifications.  
Product version  
XEPS103 Space-Saving Powerline Network Extender  
February 2007  
Manual publication date  
Product updates are available on the NETGEAR website at  
How to Print This Manual  
To print this manual, you can choose one of the following options, according to your needs. Your  
computer must have the free Adobe Acrobat Reader installed in order to view and print PDF files.  
The Acrobat Reader is available on the Adobe website at http://www.adobe.com.  
Printing a chapter. Use the PDF of This Chapter link at the top left of any page.  
Click the PDF of This Chapter link at the top right of any page in the chapter you want to  
print. The PDF version of the chapter you were viewing opens in a browser window.  
Click the print icon in the upper left of the window.  
Tip: If your printer supports printing two pages on a single sheet of paper, you can  
save paper and printer toner by selecting this feature.  
Printing the full manual. Use the Complete PDF Manual link at the top left of any page.  
Click the Complete PDF Manual link at the top left of any page in the manual. The PDF  
version of the complete manual opens in a browser window.  
Click the print icon in the upper left of the window.  
Tip: If your printer supports printing two pages on a single sheet of paper, you can  
save paper and printer toner by selecting this feature.  
iv  
v1.0, February 2007  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
XEPS103 Space-Saving Powerline Network Extender User Guide  
Package Contents  
The product package should contain the following items:  
One XEPS103 Space-Saving Powerline Network Extender  
Power cord  
XEPS103 Resource CD, including:  
— This guide.  
XEPS103 Installation Guide.  
— Encryption utility  
Printed XEPS103 Installation Guide, Warranty Registration Card, and Support Information  
Card.  
If any of the parts are incorrect, missing, or damaged, contact your NETGEAR dealer. Keep the  
carton, including the original packing materials, in case you need to return the Powerline extender  
for repair.  
Label Information and Status Lights  
The Powerline extender has a label with important information and status light indicators.  
Familiarize yourself with these features of your product.  
The Label  
The label on the bottom of the Powerline extender contains the items listed below.  
MAC address  
Model number  
Serial number  
Unique device Passcode (PWD)  
1
v1.0, February 2007  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
XEPS103 Space-Saving Powerline Network Extender User Guide  
Front Panel Status Lights  
The front panel of the XEPS103 contains status lights. You can use them to verify connections.  
The table below describes the lights on the front panel.  
Table 1-1. Front Panel Status Light Descriptions  
Status  
Description  
Light  
Power  
On green solid. Power is supplied to the Powerline extender.  
Off. Power is not supplied to the Powerline extender.  
Ethernet • On green solid. The Ethernet port is linked but there is no activity.  
Blink. Data is being transmitted or received on the Ethernet port.  
Off. No link is detected.  
HomePlug • On. The HomePlug port has detected another PowerLine device on  
the PowerLine network.  
Blink. Data is being transmitted or received on the PowerLine  
network.  
Off. No other PowerLine devices detected on the PowerLine network.  
2
v1.0, February 2007  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
XEPS103 Space-Saving Powerline Network Extender User Guide  
How the Powerline Extender Fits in Your Network  
Besides its function as a Powerline adapter, the XEPS103 acts as the power adapter for your router.  
Thus power can be provided to both the XEPS103 and your router through one AC power outlet.  
You can use the XEPS103 Powerline Extender with other HomePlug Powerline adapters (such as  
the XE103 Wall-plugged Ethernet Adapter) to implement or extend an Ethernet local area network  
(LAN) anywhere in your house using your existing electrical power line in place of a dedicated  
LAN wiring infrastructure. An example is illustrated in the following diagram for a minimal  
network consisting of two PowerLine devices:  
Internet  
Access  
Router  
Computer  
XEPS103  
Ethernet Network  
PowerLine Network  
(always encrypted)  
Computer  
XE103  
Ethernet Network  
Figure 1-1  
Follow the instructions below to set up your Powerline extender.  
Prepare to Install Your Powerline Extender  
The XEPS103 is designed for easy installation. Check that these minimum requirements are met.  
Your router uses a 12V 1A power adapter. This includes, but is not limited to, the following  
Netgear router and switch models:  
FVS318  
GS105, GS605, GS608  
WG102  
WGPS606  
WGR614, WGT624, WGT624SC  
3
v1.0, February 2007  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
XEPS103 Space-Saving Powerline Network Extender User Guide  
WPN824, WPNT834  
WNR834M, WNR834B  
If in doubt, check the label on your router’s power adapter.  
Your Ethernet network is set up and an Ethernet LAN port is available on your router.  
Your Internet connection is working.  
Each computer or device to be used on your network has an Ethernet port.  
Connect the XEPS103 to the Router  
1. Disconnect your router from its power adapter.  
2. Plug the gray dual output cable, attached to the XEPS103 Space-Saving Powerline Network  
Extender, into a LAN port and DC power inlet on your router.  
Figure 1-2  
4
v1.0, February 2007  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
XEPS103 Space-Saving Powerline Network Extender User Guide  
3. Plug the XEPS103 Powerline Extender into an electrical outlet. Take care that the electrical  
outlet is not controlled by a wall switch so as to avoid someone does not unknowingly turn off  
power to your adapter. Check that the XEPS103 power light comes on.  
Do not connect the Powerline extender to a power  
strip, extension cord, or surge protector as this may  
prevent it from working properly or degrade the  
network performance.  
Do not tie or twist the XEPS103 power cord with the  
dual output cable, or any other Ethernet cable, as this  
may degrade the network performance.  
WARNING!  
4. Wait for the router to indicate that the LAN port that is connnected to the XEPS103 Powerline  
Extender is linked and active. On the XEPS103, check that the Ethernet and Powerline status  
LEDs are on and blinking. Refer to Table 1-1 for a detailed explanation of the LED behavior.  
Connect other Ethernet Powerline Extenders  
1. Before plugging in your other PowerLine devices, take a note of the device password printed  
on the label on the back of each device. You will need this password later if you want to  
change the PowerLine network password. If you are adding more than one other Powerline  
extender, also note the MAC address given on the label, so that you will know which device  
the password is for.  
2. Plug your other PowerLine devices into power outlets in your home near to the other  
computers and peripherals to be included in your PowerLine local area network.  
3. Use an Ethernet cable to connect an Ethernet port on each of the computers and peripherals to  
the nearest PowerLine device.  
4. When you plug in a second Powerline extender into a power outlet, check the blue HomePlug  
LEDs. They should turn on and then briefly blink at the same time as the Ethernet activity  
LED.  
This completes the PowerLine installation.  
5
v1.0, February 2007  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
XEPS103 Space-Saving Powerline Network Extender User Guide  
Install the XEPS103 PowerLine Encryption Utility  
(Highly Recommended)  
The utility gives you the option of setting a unique encryption PowerLine network password.  
Important features:  
The encryption password is not case-sensitive.  
Each device must be set to exactly the same encryption password—if they are to communicate  
on the same network. PowerLine devices on different networks will not be able to  
communicate.  
A default button resets the encryption password to the default password (HomePlug).  
The encryption password can protect your network from unauthorized access through the  
PowerLine network.  
A device password is printed on each NETGEAR PowerLine product. This is not the network  
password, but you are required to enter it if you are setting the network password with another  
Powerline extender device.  
6
v1.0, February 2007  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
XEPS103 Space-Saving Powerline Network Extender User Guide  
To install the PowerLine Encryption Utility, follow these steps:  
1. Insert the XEPS103 Resource CD into a CD drive on the computer that is connected to your  
router. The CD starts automatically. The following screen is displayed:  
Figure 1-3  
If the CD does not start automatically:  
Go to My Computer on the Windows Start menu, and double-click the drive that contains  
the XEPS103 Resource CD or  
Select the CD drive and click on the Autorun.exe executable file.  
2. Click Install Encryption Utility. A dialog will give you the choice between installing from the  
CD, or checking for an upgrade. If you click the Check for Upgrade button, the CD software  
will check a Netgear server for a newer version of the utility. If found, the newer version will  
be downloaded and run. If the utility on the CD is up-to-date, or you click the Install from CD  
button, the setup program on the CD will be run.  
7
v1.0, February 2007  
Download from Www.Somanuals.com. All Manuals Search And Download.  
XEPS103 Space-Saving Powerline Network Extender User Guide  
3. A Welcome screen appears.  
Figure 1-4  
4. Click Next and follow the instructions on the screen until the installation of the utility is  
complete.  
5. When the installation is complete, click Finish.  
Set Your Network Password  
The fastest and most reliable way to set the network password is to set the password for all devices  
at once. To do this, you need the device password on the back label of each PowerLine device.  
There are two steps to setting the password: first enter the device password for each remote  
PowerLine device, and then set the network password.  
1. Enter the device password for each remote PowerLine device:  
a. Make sure that all PowerLine devices are plugged into 100~240V AC wall sockets.  
8
v1.0, February 2007  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
XEPS103 Space-Saving Powerline Network Extender User Guide  
b. Start the PowerLine encryption utility and click the Main tab.  
Figure 1-5  
c. Check that the utility lists all the remote PowerLine devices  
d. Select a PowerLine device and, if more than one remote device is listed, identify it from  
the MAC address.  
e. Click Enter Password.  
Figure 1-6  
9
v1.0, February 2007  
Download from Www.Somanuals.com. All Manuals Search And Download.  
XEPS103 Space-Saving Powerline Network Extender User Guide  
f. Enter the password recorded from the label on the back of the selected PowerLine device.  
g. Click OK.  
h. Repeat this step for all devices that you want attached to your network.  
2. Set the network password.  
a. Select the Security tab.  
Figure 1-7  
b. Type a password in the Private Network Password text box.  
c. Click Set All Devices. A pop-up window indicates that the operation was successful.  
10  
v1.0, February 2007  
Download from Www.Somanuals.com. All Manuals Search And Download.  
XEPS103 Space-Saving Powerline Network Extender User Guide  
Add a Device to an Existing PowerLine Network  
To add a device to a PowerLine network with the default network password, all you need to do is  
plug the new device into a power outlet.  
If the network password has been set, then you will need to run the PowerLine encryption utility to  
set the new device to the network password. How you do this depends on whether the computer  
running the PowerLine encryption utility is connnected directly to the new PowerLine device  
(local) or is connected to a different device in the PowerLine network (remote).  
Adding a New Device from a Locally Connected Computer  
1. Plug the new PowerLine device into an available AC power outlet and connect it to an  
Ethernet port on the computer.  
2. Start the PowerLine encryption utility and select the Security tab.  
3. Type the network password in the Private Network Password text box and click Set Local  
Device Only.  
4. Select the Main tab and check that the other devices in the PowerLine network appear in the  
device list. It may take a minute or two for all devices in the network to be detected.  
Adding a New Device from a Remotely Connected Computer  
1. Note the device password given on the label on the back of the new PowerLine device.  
2. Plug the new PowerLine device into an AC power outlet.  
3. Start the PowerLine encryption utility on the remote computer and select the Security tab.  
4. Click Use Default (Public Network). The password in the Private Network Password text box  
changes to the default password, HomePlug.  
5. Click Set All Devices.  
6. Select the Main tab and wait for the new PowerLine device to be listed.  
7. Select the new PowerLine device from the device list, and click Enter Password.  
8. In the pop-up window, enter the password from the back label of the device and click OK.  
9. Select the Security tab.  
10. Re-enter the network password in the Private Network Password text box, and then click Set  
All Devices.  
11  
v1.0, February 2007  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
XEPS103 Space-Saving Powerline Network Extender User Guide  
Troubleshooting  
This chapter gives information about troubleshooting your XEPS103 Space-Saving Powerline  
Network Extender. After each problem description, instructions are provided to help you diagnose  
and solve the problem.  
NETGEAR Product Registration, Support, and Documentation  
Register your product at http://www.netgear.com/register.  
Product updates and Web support are available at:  
When the Powerline extender is connected to the Internet, click the Knowledge Base or the  
Documentation link under the Web Support menu to view support information or the  
documentation for the Powerline extender.  
Basic Functioning  
After you plug in the Powerline extender, the following sequence of events should occur:  
1. When power is first applied, verify that the Power light is on.  
2. After approximately 10 seconds, check the LEDs on the Powerline extender. The following  
should occur:  
a. The power LED is solid green.  
b. The blue HomePlug LED is lit.  
c. The Ethernet LED blinks.  
If any of these conditions does not occur, refer to the appropriate following section.  
Power Light Not On  
Make sure that, if power to the AC power outlet is controlled by a wall switch, the wall switch is in  
the on position.  
Verify that the wall socket is live. To do this, disconnect the Powerline extender and plug in  
another electrical product, such as a lamp or a hairdryer.  
12  
v1.0, February 2007  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
XEPS103 Space-Saving Powerline Network Extender User Guide  
If the Power LED still does not come on, and you have confirmed the power outlet is live, you  
have a hardware problem and should contact technical support.  
HomePlug Light Not On  
If the power light is on but the HomePlug light is not, check the following:  
Make sure that power is being provided to more than one PowerLine device. Another  
PowerLine device must be installed for successful communication across the PowerLine.  
Verify that the network password is the same on all devices in the PowerLine network.  
Ethernet Light is Off  
Make sure that the Ethernet cable is plugged in properly to a router LAN port.  
On the attached Ethernet device or network adapter card, check that the Link light is on.  
13  
v1.0, February 2007  
Download from Www.Somanuals.com. All Manuals Search And Download.  
XEPS103 Space-Saving Powerline Network Extender User Guide  
Technical Specifications  
This section provides default settings and technical specifications for the XEPS103 Space-Saving  
Powerline Network Extender.  
Default Configuration Settings  
Table 1-1. PowerLine Device Default Configuration Settings  
Feature  
Network  
Description  
Port Speed  
Port Duplex  
10/100 Mbps, Auto-negotiation  
Auto-negotiation  
Auto uplink  
Administration  
Device password  
PowerLine  
See product label.  
HomePlug  
Encryption password  
Technical Specifications  
Power input  
100~240V AC  
12V DC at 1 A. Tolerance <5%  
Power output  
Dimensions  
46mm x 70mm x 125mm (Height x Width x Length)  
0.5 kg  
Weight  
Operating temperature  
Operating humidity  
Storage humidity  
Powerline standard  
HomePlug Frequency  
Data transfer rate  
32° to 104° F (0° to 40°C)  
10-90% maximum relative humidity, noncondensing  
5-95% maximum relative humidity, noncondensing  
HomePlug 1.0  
4.3-20.9 Mhz  
Up to 85 Mbps with real throughput > 25 Mbps.  
14  
v1.0, February 2007  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
XEPS103 Space-Saving Powerline Network Extender User Guide  
Data Encoding  
HomePlug 1.0: Othogonal Frequency Division Multiplexing (OFDM),  
DQPSK, DBPSK, ROBO  
HomePlug Security  
DES (56 bit)  
Network Protocol  
Compatibility  
IEEE 802.3 (10Base-T); IEEE 802.3u (100Base-Tx); IEEE 802.3x (full-  
duplex flow control)  
Electromagnetic emmissions FCC Part 15 Class B; CE-Mark, commercial; VCCI Class B; A-tick;  
3-home FCC Certificate; MIC  
Power and Safety  
UL Listed (UL 1950) /cUL IEC950; CE LVD  
CEEP  
Power adapter regulations  
15  
v1.0, February 2007  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Miele Clothes Dryer T 4839 Ci User Manual
Napoleon Grills Gas Grill PRESTIGE II 600 User Manual
NEC Projector LT 100 User Manual
Novatel Wireless Modem MCD3000 User Manual
Olympus Camera Lens 261013 User Manual
Olympus Computer Drive MAUSB 1 User Manual
Onkyo Car Amplifier PA MC5501 User Manual
Panasonic Car Video System BT LH900A User Manual
Panasonic Electric Shaver ERGB40 User Manual
Panasonic Router 324566 A User Manual