NETGEAR Network Card WG511v2 User Manual

d. Click Finish to complete the installation. You will see the WG511v2  
2. NEXT, INSTALL THE WG511V2 WIRELESS PC CARD.  
system tray icon on the lower right portion of the Windows task bar.  
)NSTALLATION 'UIDE  
a. Hold the PC Card with the NETGEAR logo facing up and insert it into a  
CardBus slot. After a short delay, the Found New Hardware Wizard displays.  
3. NOW, CONFIGURE YOUR WG511V2 AND SAVE THE PROFILE.  
WG511v2 Wireless PC Card  
Note: If you have  
installed Windows  
XP Service Pack 2,  
click “Yes, this time  
only” or “Yes, now  
and every time I  
connect a device” to  
proceed.  
a. Open the WG511v2 Smart Wireless Settings Utility by clicking on the icon in the  
Windows system tray.  
Follow These Quick Steps to Install Your  
WG511v2  
These basic setup instructions assume that you will connect to a wireless access point or  
wireless router, and you are not using WEP security. Please refer to the online help and the  
Reference Manual on your CD for instructions on configuring WEP, Ad-hoc mode, or  
advanced options.  
Note: If a Windows XP logo testing warning appears, click Continue Anyway to  
proceed.  
Estimated Completion Time: 5-15 minutes for each notebook PC.  
b. Next you will be prompted to enable the NETGEAR Smart Wireless Settings  
Utility configuration utility.  
Windows XP Installation  
The utility opens to the Settings tab page.  
b. Change the Network Name SSID to match your network.  
1. First, install the WG511v2 software.  
Tip: To view the available wireless networks, use the drop-down list or the Net-  
works tab and choose the one you want.  
a. Power on your notebook, let the operating system boot up completely, and log in  
as needed.  
c. Click Apply to activate the connection.  
b. Insert the Resource CD for the WG511v2 into your  
CD-ROM drive. The CD main page shown below will load.  
Tip: Create work and home profiles. Then, activate whichever one you need for  
your current location.  
Note: The status bar at the bottom of the utility reports the speed of your connection. 54  
Mbps speed is only possible when your wireless network has a 54 Mbps access point such  
as the NETGEAR WGR614 54 Mbps wireless router.  
Click Yes to accept this option.  
Or, choose No to enable Windows XP Zero configuration utility. You can switch  
between the utilities by going to Control Panel > Network Connections and  
clicking on your wireless network card. Click the Properties button and select the  
Wireless Networks tab. Check or clear the “Use Windows to configure my wire-  
less network settings” check box.  
4. FINALLY, VERIFY WIRELESS NETWORK CONNECTIVITY.  
a. Verify that the status monitor information at the bottom of the utility matches  
your wireless network.  
b. Check the WG511v2 LEDs: Green (Link light): Blinking indicates the WG511 is  
trying to establish a connection but is unable to do so. Amber (Activity light):  
Blinking indicates the WG511v2 has a connection and is transmitting or  
receiving data.  
c. Click the Install Driver & Utility link.  
d. Follow the InstallShield Wizard steps, and click Finish when done to restart your  
c. Verify connectivity to the Internet or network resources.  
computer.  
c. You will also be prompted to choose the country you are located in. Select your  
location from the list.  
Note: If you are unable to connect, see the troubleshooting tips in the Installation  
chapter of the Reference Manual on the Resource CD.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Miele Double Oven 10 103 420 User Manual
Miglia Technology TV Receiver TVMini 2 User Manual
Mr Coffee Coffeemaker GB Series User Manual
NETGEAR Network Router RT328 User Manual
Nokia Headphones BH 208 User Manual
Nuvo Stereo Amplifier LSA40 User Manual
Omnimount Indoor Furnishings RSVS2U User Manual
Opticon Scanner LPN 1736 User Manual
Panasonic Cordless Telephone KX TGE210 User Manual
Panasonic CRT Television CT 27G24 User Manual