Xen IPK
IAD MEGACO TRUNK EXTENSION
QUICK SETUP GUIDE
NEC Business Solutions Ltd
Document No.: 8684
Release: 1.0 June 2004
Download from Www.Somanuals.com. All Manuals Search And Download.
Disclaimer
NEC shall not be liable for any direct, indirect, consequential or incidental damages about the use of this
equipment, manual or any related materials.
The information in this technical manual is advisory in nature and is subject to change. NEC may make
improvements and changes in the products described in this manual without notice. Changes will be
periodically made to the information in the new editions.
Efforts have been made to ensure that the contents of this manual are correct. Should you find any error,
NEC welcomes your comments to improve our communications, please contact NEC on 1800 036 136.
Contents of this manual are subject to change without prior notice at the discretion of NEC Business
Solutions Ltd.
This document has been prepared for the use of employees and customers of NEC Business Solutions
Ltd and may not be reproduced without the prior, written approval of NEC Business Solutions Ltd.
Copyright 2004
NEC Business Solutions Ltd
633-647 Springvale Road
Mulgrave Vic 3170
IAD Megaco Extension Quick Setup Guide
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
June 2004
NEC Business Solutions Ltd
THIS PAGE INTENTIONALLY LEFT BLANK
iv
Disclaimer
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up the Megaco
Station Application
SECTION
1
HARDWARE SETUP
Figure D-1: IAD(8)-U( ) ETU
IPK IAD Megaco Extension Quick Setup Guide
33
Download from Www.Somanuals.com. All Manuals Search And Download.
June 2004
NEC Business Solutions Ltd
1.1
Boot Up Sequence
The LED chart shows the status of the IAD(8)-U( ) ETU card during
boot up. The LED conditions change as the IAD(8)-U( ) ETU passes
through different boot states.
Table 1 Boot Up Sequence LED Patterns
D8
CH1
D6
CH2
D4
CH3
D2
CH4
D7
CH5
D5
CH6
D3
CH7
D1
CH8
D12
LIVE
STATE
1
2
3
4
5
6
z
z
z
z
z
z
z
z
@
@
@
@
@
@
z = LED ON
= LED OFF
@ = LED Flashing
1.2
Connectors
J6 = Default Ethernet connection
1.3
S2 DIP Switch Settings
Table D-1 S2 DIPSW Settings
Auto
Sense
No. of
Ports
Reserved
Mode Operation
SW8
SW1
SW2
SW3
SW4
SW5
SW6
SW7
OFF
OFF
OFF
ON
ON
ON
OFF
OFF
ESI(8)-U10 ETU
1. Configure DIPSW S2 in accordance to Table 2. Place the IAD(8)-U( )
ETU in the Xen IPK KSU.
2. Connect the Ethernet cable to connector J6.
3. The CH1~CH8 LEDs start to run indicating that the system is initial
ising the IP Networking parameters. The Status LED (D12) is red (refer
to Table 1 Boot Up Sequence LED Patterns).
4. Once all the LEDs are OFF and the Status LED (D12) is flashing red,
the IAD(8)-U( ) can be set up with the system.
34
Hardware Setup
Download from Www.Somanuals.com. All Manuals Search And Download.
Xen IPK
Xen IPK Programming
SECTION
2
After the Dip Switches have been set and the IAD ETU has been installed in
the Xen IPK KSU, you are ready to program the settings the for the IAD
ETU.
XEN IPK
PROGRAMMING
The IAD (8)-U( ) ETU (MEGACO Station) is recognised by the Xen IPK
system as a ESI(8)-U( ) ETU. This ETU takes a longer time to initialize than
the other Xen IPK ETUs and must be programmed using Memory Block 7-1
(Card Interface Slot Assignment).
2.1
Programming the ETU Interface Slot
The following procedure provides the general directions for Xen
IPK programming for the ETU Interface Slot Assignment.
1. From port 01 or 02, enter programming mode.
2. Press T ULKL.
3. Assign the Card Interface Slot Assignment by pressing LK7 and LK1.
4. PressA, B or Cfor the cabinet number of KSU where the IAD
(8)-U( ) ETU is installed.
5. PressLto move the cursor to the right.
6. Enter slot number (1~8) of the KSU containing the IAD (8)-U( ) ETU.
7. Press
S
to change the page number (Page 2) and assign the ESI
ETU. Press LK1.
8. Press
N
to write the data.
9. Additional programming is required to assign telephone type and
station number.
10. Assign the telephone type assignment by pressing LK7 and LK2.
If assigning MEGACO terminals, assign ports as TEL=LK2.
11. Assign station number assignment on a per port basis (MB 4-10).
IPK IAD Megaco Extension Quick Setup Guide
35
Download from Www.Somanuals.com. All Manuals Search And Download.
June 2004
NEC Business Solutions Ltd
SECTION
3
When installed for the first time, the IAD (8)-U( ) ETU, comes up with factory
set default parameters as shown in Table D-2 Factory Network Settings.
IAD (8)-U( ) ETU WEB
PROGRAMMING
Table D-2 Factory Network Settings
neciad
Host Name
192.168.1.100
255.255.255.0
192.168.1.1
IP Address
Subnet Mask
Default Gateway
In this configuration, the ETU cannot run in any randomly given
environment, and its parameters must be redefined before the IAD (8)-U( )
ETU can work in your environment.
1. Boot up a PC with IP Address: 192.168.1.X, Subnet Mask:
255.255.255.0. Connect to the IAD(8)-U( ) either via a crossover cable
or a small hub.
2. Connect to the IAD (8)-U( ) ETU via your Web Browser to the following
link:
The IAD (8)-U( ) ETU supports Microsoft Internet Explorer 5.0
and higher.
3. When the login screen appears, enter the Login ID and password. Click
login.
Default login ID = admin
Default password = password
4. Set the IP Address, Subnet Mask, Host Name, and Default IP
parameters in the IAD (8)-U( ) ETU Card tab and select Submit.
5. Set the IP Station Encoding Preference, Packet Size, Jitter Depth and
the IP Address (or use DHCP if using a DHCP Server) under the Port
Tab and select Submit.
6. Select the System tab, then select Reset the Card. The ETU goes
through a reboot cycle. This may take a few minutes.
7. Disconnect the crossover cable and connect the IAD (8)-U( ) ETU
(MEGACO Station) to your network.
The ETU is now ready for operation.
36
IAD (8)-U( ) ETU Web Programming
Download from Www.Somanuals.com. All Manuals Search And Download.
|