NEC LCD Series
®
MultiSync
™
™
LCD1525V
User’s Manual
User’s Manual
ou can
Y
register your
product online at
/
.nectech.com
www
productregistration
78134641.wpc
1
5/4/99, 5:37 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE
THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS
CAN BE FULLY INSERTED.
REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK • DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause
electric shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit.
This symbol alerts the user that important literature concerning the operation and maintenance of this
unit has been included. Therefore, it should be read carefully in order to avoid any problems.
Canadian Department of Communications Compliance Statement
DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-
Causing Equipment Regulations.
C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations
according to C.S.A. C22.2 No. 950.
FCC Information
1.Use the attached specified cables with the LCD1525V color monitor so as not to interfere with
radio and television reception.
(1) Please use the supplied power cable or equivalent to ensure FCC compliance.
(2) Please use the supplied AC Adapter.
(3) Shielded video signal cable.
Use of other cables and adapters may cause interference with radio and television
reception.
2. This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuanttopart15oftheFCCRules. Theselimitsaredesignedtoprovidereasonable
protection against harmful interference in a residential installation. This equipment gener-
ates, uses, and can radiate radio frequency energy, and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult your dealer or an experienced radio/TV technician for help.
If necessary, the user should contact the dealer or an experienced radio/television technician
for additional suggestions. The user may find the following booklet, prepared by the Federal
Communications Commission, helpful: ”How to Identify and Resolve Radio-TV Interference
Problems.“ This booklet is available from the U.S. Government Printing Office, Washington,
D.C., 20402, Stock No. 004-000-00345-4.
1
78134641.wpc
3
5/4/99, 5:37 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
You can register your product online at
Your new NEC Technologies MultiSync® LCD monitor box* should
contain the following:
• MultiSync LCD1525V™
monitor with tilt base
• Power Cord
• AC Adapter
• Video Signal Cable
• User’s Manual
MultiSync LCD1525V
monitor with Video Signal Cable
and AC Adapter
M
u
lt
iS
y
n
c
L
C
D1525V
MultiSync
MultiSync
LCD
LCD
1525V
r’s 1M525V
U
U
se
®
®
se
Power Cord
r’s M
a
a
n
n
u
u
a
a
l
l
User’s Manual
* Remember to save your original box and packing material to transport or ship the monitor.
2
78134641.wpc
4
5/4/99, 5:37 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start
To attach the MultiSync® LCD monitor to your system, follow these
instructions:
1. Turn off the power to your computer.
2. For the PC: Connect the 15-pin mini D-SUB of the appropriate signal cable
to the connector of the display card in your system (Figure A.1). Tighten all screws.
For the Mac: Connect the MultiSync LCD1525V™ Macintosh cable adapter to the computer
(Figure B.1). Attach the 15-pin mini D-SUB end of the appropriate signal cable to the
MultiSync LCD1525V Macintosh cable adapter (Figure B.1). Tighten all screws.
NOTE: To obtain the MultiSync LCD1525V Macintosh cable adapter,
call NEC Technologies at (800) 820-1230.
Remove connector cover and cable cover on back of monitor.
3. Connect the 15-pin mini D-SUB of the video signal cable to the appropriate connector on
the back of the monitor (Figure C1).
Place the Video Signal Cable under Clip A. Then place AC Adapter Cable under Clip B.
Replace connector cover and cable cover.
NOTE: Incorrect cable connections may result in irregular operation, damage
display quality/components of LCD module and/or shorten the module’s life.
4. Connect one end of the power cord to the MultiSync LCD Series monitor and the other
end to the power outlet (Figure D.1).
5. Turn on the monitor (Figure E.1) and the computer.
6. To complete the setup of your MultiSync LCD monitor, use the following OSM™ controls:
• Auto Adjust Contrast
• Auto Adjust
Refer to the Controls section of this User’s Manual for a full description of these OSM controls.
NOTE: For download information on the Windows 95/98 INF file for your MultiSync
LCD1525V monitor, refer to the References section of this User’s Manual.
NOTE: If you have any problems, please refer to the Troubleshooting section of
this User’s Manual.
15-pin
mini D-SUB
15-pin
mini
D-SUB
Mac Adapter
(not included)
Figure A.1
Figure B.1
3
78134641.wpc
5
5/4/99, 5:37 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start cont.
Figure C.1
Clip A
Clip B
Figure D.1
Power Switch
M
u
lti
S
Figure E.1
4
78134641.wpc
6
5/4/99, 5:37 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
5
78134641.wpc
7
5/4/99, 5:38 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls
OSM™ (On-Screen-Manager) Controls
The OSM controls on the front of the monitor function as follows:
Control
Main Menu
Sub-Menu
EXIT
Exits the OSM controls.
Exits to the OSM controls
main menu.
CONTROL
CONTROL
PROCEED
/
Moves the highlighted
area up/down to select
one of the controls.
Moves the highlighted
area left/right to
select control menus.
Has no function.
Moves the highlighted area
up/down to select one of the
controls.
Moves the bar left/right
to increase or decrease
the adjustment.
Activates Auto Adjust feature.
In Tool and Information Mode,
opens additional window.
/
RESET: The currently
highlighted control to
the factory setting.
Resets all the controls within
the highlighted menu.
Resets the highlighted control.
NOTE: When RESET is pressed, a warning window will appear
allowing you to cancel the reset function.
Brightness and Contrast
Brightness: Adjusts the overall image and background screen brightness.
Contrast: Adjusts the image brightness in relation to the background.
Auto Adjust: Corrects the image displayed for non-standard video inputs.
Auto Adjust
Automatically adjusts the Position and H. Size and fine settings.
Position
Controls horizontal and vertical image position within the display area of
the LCD.
Auto Adjust: Automatically sets the horizontal and vertical image
position within the display area of the LCD.
Image Adjust
H.SIZE: Adjusts the horizontal size by increasing or decreasing this setting.
Fine:
Improves focus, clarity and image stability by increasing or decreasing
the Fine setting.
Auto Adjust: Automatically adjusts the H. Size or Fine settings.
6
78134641.wpc
8
5/4/99, 5:38 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls
AccuColor® Control System
Five color presets select the desired color setting. If a setting is adjusted, the name of
the setting will change to Custom
.
Color Gain (Red, Green, Blue): Increases or decreases Red, Green or Blue color
depending upon which is selected. The change in color will appear on screen
and the direction (increase or decrease) will be shown by the color bars.
Tools
Language: OSM control menus are available in seven languages.
OSM™ Position: You can choose where you would like the OSM control image
to appear on your screen. Selecting OSM Location allows you to manually adjust
the position of the OSM control menu left, right, up or down.
OSM Turn Off: The OSM control menu will stay on as long as it is in use. In
the OSM Turn Off submenu, you can select how long the monitor waits after the
last touch of a button to shut off the OSM control menu. The preset choices are
10, 20, 30, 60 and 120 seconds.
OSM Lock Out: This control completely locks out access to all OSM control
functions. When attempting to activate OSM controls while in the Lock Out
mode, a screen will appear indicating the OSM controls are locked out. To
activate the OSM Lock Out function, press PROCEED, then and hold down
simultaneously. To de-activate the OSM Lock Out, press PROCEED, then and
hold down simultaneously.
Factory Preset: Selecting Factory Preset allows you to reset all OSM control
settings back to the factory settings. The RESET button will need to be held down
for several seconds to take effect. Individual settings can be reset by highlighting
the control to be reset and pressing the RESET button.
Resolution Notifier: This optimal resolution is 1024 x 768. If ON is selected,
a message will appear on the screen after 2 minutes, notifying you that the
resolution is not at 1024 x 768.
Information
Display Mode: Provides information about the current resolution display and
technical data including the preset timing being used and the horizontal and
vertical frequencies.
7
78134641.wpc
9
5/4/99, 5:38 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Recommended Use
Safety Precautions and Maintenance
FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE
FOLLOWING WHEN SETTING UP AND USING
THE MULTISYNC® LCD COLOR MONITOR:
• DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and
opening or removing covers may expose you to dangerous shock hazards or other
risks. Refer all servicing to qualified service personnel.
• Do not spill any liquids into the cabinet or use your monitor near water.
• Do not insert objects of any kind into the cabinet slots, as they may touch danger-
ous voltage points, which can be harmful or fatal or may cause electric shock, fire
or equipment failure.
• Do not place any heavy objects on the power cord. Damage to the cord may
cause shock or fire.
• Do not place this product on a sloping or unstable cart, stand or table, as the
monitor may fall, causing serious damage to the monitor.
• When operating the MultiSync LCD monitor with its AC 220-240V power supply,
use a power supply cord that matches the power supply voltage of the AC power
outlet being used. The power supply cord you use must have been approved by
and comply with the safety standards of your country.
• Use supplied AC Adapter. Do not place any objects onto the AC Adapter and do
not use the AC Adapter outdoors.
• The inside of the flourescent tube located within the LCD monitor contains mercury.
Please follow the bylaws or rules of your municipality to dispose of the tube
properly.
• In UK, use a BS-approved power cord with molded plug having a black (5A) fuse
installed for use with this monitor. If a power cord is not supplied with this monitor,
please contact your supplier.
Immediately unplug your monitor from the wall outlet and refer servicing to qualified
service personnel under the following conditions:
• When the power supply cord or plug is damaged.
• If liquid has been spilled, or objects have fallen into the monitor.
• If the monitor has been exposed to rain or water.
• If the monitor has been dropped or the cabinet damaged.
• If the monitor does not operate normally by following operating instructions.
• Allow adequate ventilation around the monitor so that heat can properly
dissipate. Do not block ventilated openings or place the monitor near a
radiator or other heat sources. Do not put anything on top of monitor.
• The power cable connector is the primary means of detaching the system
from the power supply. The monitor should be installed close to a power
CAUTION
outlet which is easily accessible.
• Handle with care when transporting. Save packaging for transporting.
68
78134641.wpc
10
5/4/99, 5:38 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Recommended Use
CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR
CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE
FOLLOWING WHEN YOU POSITION THE MONITOR:
• For optimum performance, allow 20 minutes for
warm-up.
• Adjust the monitor height so that the top of the
screen is at or slightly below eye level. Your eyes
should look slightly downward when viewing the
middle of the screen.
•
Position your monitor no closer than 16 inches
and no further away than 28 inches from your
eyes. The optimal distance is 21 inches for the
MultiSync® LCD 1525V™ monitor.
• Rest your eyes periodically by focusing on an object at least 20 feet away.
Blink often.
• Position the monitor at a 90° angle to windows and other light sources to
minimize glare and reflections. Adjust the monitor tilt so that ceiling lights do
not reflect on your screen.
• If reflected light makes it hard for you to see your screen, use an anti-glare filter.
• Clean the LCD monitor surface with a lint-free, non-abrasive cloth. Avoid using
any cleaning solution or glass cleaner!
• Adjust the monitor’s brightness and contrast controls to enhance readability.
• Use a document holder placed close to the screen.
• Position whatever you are looking at most of the time (the screen or
reference material) directly in front of you to minimize turning your head
while you are typing.
• Avoid displaying fixed patterns on the monitor for long periods of time to avoid
image persistence (after-image effects).
• Get regular eye checkups.
Ergonomics
To realize the maximum ergonomics benefits, we recommend the following:
•
•
•
•
•
Do not position the Contrast control to its maximum setting
Use the preset Size and Position controls with standard signals
Use the preset Color Setting
Use non-interlaced signals with a vertical refresh rate between 60-75Hz
Do not use primary color blue on a dark background, as it is difficult to see and
may produce eye fatigue to insufficient contrast
For more detailed information on setting up a healthy work environment, call NEC
at (800) 820-1230, NEC FastFacts™ information at (800) 366-0476 and request
document #900108 or write the American National Standard for Human Factors
Engineering of Visual Display Terminal Workstations – ANSI-HFS Standard
No. 100-1988 – The Human Factors Society, Inc. P.O. Box 1369, Santa Monica,
9
78134641.wpc
11
5/4/99, 5:38 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Monitor
MultiSync® LCD1525V™
Notes
Specifications
LCD Module
Monitor
15.1 inch
15.1 inch
1024 x 768
Diagonal:
Active matrix; thin film transistor (TFT)
liquid crystal display (LCD); 0.30 mm dot
pitch; 200cd/m2 white luminence;
200:1 contrast ratio, typical
Viewable Image Size:
Native Resolution (Pixel Count):
Input Signal
Video:
Sync:
ANALOG 0.7 Vp-p/75 Ohms
Separate sync. TTL Level
Horizontal sync. Positive/Negative
Vertical sync. Positive/Negative
Display Colors
Viewing Angle
Analog input:
16,194,277 colors with dithering
Depends on display card used.
Left/Right:
Up/Down:
± 55°
40°
Synchronization
Range
Horizontal:
Vertical:
24.8 kHz to 48.4 kHz
56.2 Hz to 75.0 Hz
Automatically
Automatically
Resolutions Supported
720 x 400* VGA text
640 x 480* at 60 Hz to 75 Hz
800 x 600* at 56 Hz to 75 Hz
Some systems may not support
all modes listed.
Resolution based on horizontal and
vertical frequencies only
1024 x 768 at 60 Hz ................................ NEC cites recommended resolution at
60 Hz for optimal display performance.
Active Display Area
Horizontal:
Vertical:
307 mm/12.1 inches
230 mm/9.1 inches
Dependent upon signal timing used,
and does not include border area.
Power Supply
Current Rating
Dimensions
AC 100 – 240 V @ 50/60 Hz
0.4 A @ 100
–
120 V/0.25 A @ 220 – 240 V
370 mm (W) x 325 mm (H) x 151 mm (D)
14.6 inches (W) x 12.8 inches (H) x 5.9 inches (D)
Weight
4 kg
8.8 lbs
Environmental Considerations
Operating Temperature:
Humidity:
5°C to 35°C/41°F to 95°F
30% to 80%
Feet:
0 to 10,000 Feet
Storage Temperature:
Humidity:
-10°C to +60°C/14°F to 140°F
10% to 85%
Feet:
0 to 45,000 Feet
*
Interpolated Resolutions: When resolutions are shown that are lower than the pixel count of the LCD module, text may
appear different. This is normal and necessary for all current flat panel technologies when displaying non-native
resolutions full screen. In flat panel technologies, each dot on the screen is actually one pixel, so to expand resolutions to
full screen, an interpolation of the resolution must be done.
NOTE: Technical specifications are subject to change without notice.
10
78134641.wpc
12
5/4/99, 5:38 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
Wider Compatibility: Because the MultiSync LCD monitor is analog through and
through, it does not require special analog to digital display or interface cards
but can accept RGB input directly.
Reduced Footprint: Provides the ideal solution for environments requiring
superior image quality but with size and weight limitations. The monitor’s small
footprint and low weight allow it to be moved or transported easily from one
location to another.
AccuColor® Control System: Allows you to adjust the colors on your screen and
customize the color accuracy of your monitor to a variety of standards.
OSM™ (On-Screen Manager) Controls: Allow you to quickly and easily adjust all
elements of your screen image via simple to use on-screen menus.
ErgoDesign® Features: Enhance human ergonomics to improve the working
environment, protect the health of the user and save money. Examples include
OSM controls for quick and easy image adjustments, tilt base for preferred angle
of vision, small footprint and compliance with MPRII guidelines for lower emissions
.
Plug and Play: The Microsoft® solution with the Windows®95/98 operating
system facilitates setup and installation by allowing the monitor to send its
capabilities (such as screen size and resolutions supported) directly to your
computer, automatically optimizing display performance.
IPM™ (Intelligent Power Manager) System: Provides innovative power-saving
methods that allow the monitor to shift to a lower power consumption level when
on but not in use, saving two-thirds of your monitor energy costs, reducing
emissions and lowering the air conditioning costs of the workplace.
Multiple Frequency Technology: Automatically adjusts monitor to the display
card’s scanning frequency, thus displaying the resolution required.
FullScan™ Capability: Allows you to use the entire screen area in most resolu-
tions, significantly expanding image size.
OSM Display Screen Copyright 1999 by NEC Technologies, Inc.
11
78134641.wpc
13
5/4/99, 5:38 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
No picture
•
The signal cable should be completely connected to the display card/computer.
• The display card should be completely seated in its slot.
• Power Switch and computer power switch should be in the ON position.
• Check to make sure that a supported mode has been selected on the display
card or system being used. (Please consult display card or system manual to
change graphics mode.)
• Check the monitor and your display card with respect to compatibility and
recommended settings.
• Check the signal cable connector for bent or pushed-in pins.
Image persistence
• Image persistence is when a “ghost” of an image remains on the screen even
after the monitor has been turned off. Unlike CRT monitors, LCD monitors’
image persistence is not permanent. To alleviate image persistence, turn the
monitor off for as long as an image was displayed. If an image was on the
monitor for one hour and a ”ghost” of that image remains, the monitor
should be turned off for one hour to erase the image.
NOTE: As with all personal display devices, NEC Technologies recommends
using a screen saver at regular intervals whenever the screen is idle.
Image is unstable, unfocused or swimming is apparent
• Signal cable should be completely attached to the computer.
• Use the OSM Image Adjust controls to focus and adjust display by
increasing or decreasing the fine total. When the display mode is changed,
the OSM Image Adjust settings may need to be re-adjusted.
• Check the monitor and your display card with respect to compatibility
and recommended signal timings.
LED on monitor is not lit (no green or amber color can be seen)
• Power Switch should be in the ON position and power cord should
be connected.
• Make certain the computer is not in a power-saving mode (touch the
keyboard or mouse).
Display image is not sized properly
• Use the OSM Image Adjust controls to increase or decrease the Coarse total.
• Check to make sure that a supported mode has been selected on the display
card or system being used. (Please consult display card or system manual to
change graphics mode.)
Selected resolution is not displayed properly
• Use OSM Display Mode to enter Mode Change sub-menu and confirm that
the appropriate resolution has been selected. If not, select corresponding
option.
12
78134641.wpc
14
5/4/99, 5:38 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
References
• BBS
(978) 742-8706
NEC Technologies’ Remote Bulletin Board System is an electronic service
accessible with your system and a modem. Communication parameters
are: 300/1200/2400/9600/14.4k/28.8k/33.6k bps, no parity, 8-data bits,
1 stop bit
• Customer Service/
Technical Support
Fax
(800) 632-4662
(978) 635-7049
• Electronic Channels:
Internet ftp site: ftp.nectech.com
then download the file NECMSINF.ZIP.
• FastFacts™ Information
INFORMATION
MultiSync® LCD1525V™ monitor
(800) 366-0476
DESCRIPTION
DOCUMENT #
152501
Detailed monitor information
Glossary
Definition of terms related
to functions, features and
installation of the
900203
MultiSync monitor
More Information
Names and addresses of
other groups involved in
standards and features of
the MultiSync monitor
900204
Macintosh Connection
Detailed information on
connecting the MultiSync
monitor to a Macintosh
153006
900108
Healthy Work Environment
Detailed information on
setting up a healthy work
environment
• Literature & Sales Info
• MultiSync Fulfillment
(800) NEC-INFO [(800) 632-4636]
(800) 820-1230
[For software & accessories]
• TeleSales
(800) 284-4484
13
78134641.wpc
15
5/4/99, 5:38 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Limited Warranty
NEC Technologies, Inc. (hereinafter “NECTECH”), warrants this Product to be free from
defects in material and workmanship and, subject to the conditions set forth below, agrees
to repair or replace (at NECTECH’s sole option) any part of the enclosed unit which proves
defective for a period of three (3) years from the date of first consumer purchase. Spare parts
arewarrantedforninety(90)days. Replacementpartsorunitsmaybeneworrefurbishedand
will meet specifications of the original parts or unit.
This warranty gives you specific legal rights and you may also have other rights which vary
from state to state. This warranty is limited to the original purchaser of the Product and is not
transferable. This warranty covers only NECTECH-supplied components. Service required as
a result of third party components is not covered under this warranty. In order to be covered
under this warranty, the Product must have been purchased in the U.S.A. or Canada by the
original purchaser. This warranty only covers Product distribution in the U.S.A. or Canada by
NECTECH. No warranty service is provided outside of the U.S.A. or Canada. Proof of
Purchase will be required by NECTECH to substantiate date of purchase. Such proof of
purchase must be an original bill of sale or receipt containing name and address of seller,
purchaser, and the serial number of the product.
It shall be your obligation and expense to have the Product shipped, freight prepaid, or
delivered to the authorized reseller from whom it was purchased or other facility authorized
by NECTECH to render the services provided hereunder in either the original package or a
similar package affording an equal degree of protection. All Products returned to NECTECH
for service MUST have prior approval, which may be obtained by calling 1-800-632-4662.
The Product shall not have been previously altered, repaired, or serviced by anyone other
than a service facility authorized by NECTECH to render such service, the serial number
of the product shall not have been altered or removed. In order to be covered by this warranty
the Product shall not have been subjected to displaying of fixed images for long periods of
timeresultinginimagepersistence(afterimageeffects), accident, misuseorabuseoroperated
contrary to the instructions contained in the User’s Manual. Any such conditions will void this
warranty.
NECTECH SHALL NOT BE LIABLE FOR DIRECT, INDIRECT, INCIDENTAL, CONSEQUENTIAL,
OR OTHER TYPES OF DAMAGES RESULTING FROM THE USE OF ANY NECTECH
PRODUCTOTHERTHANTHELIABILITYSTATEDABOVE. THESEWARRANTIESAREINLIEUOF
ALL OTHER WARRANTIES EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES OR THE
LIMITATION OR EXCLUSION OF LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES SO THE ABOVE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU.
This Product is warranted in accordance with the terms of this limited warranty. Consumers
are cautioned that Product performance is affected by system configuration, software, the
application, customer data, and operator control of the system, among other factors. While
NECTECH Products are considered to be compatible with many systems, specific functional
implementation by the customers of the Product may vary. Therefore, suitability of a Product
for a specific purpose or application must be determined by consumer and is not warranted
by NECTECH.
For the name of your nearest authorized NECTECH service facility, contact NECTECH
at 1-800-632-4662.
14
78134641.wpc
16
5/4/99, 5:38 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
TCO’99
Congratulations! You have just purchased a TCO’99 approved and
labeled product! Your choice has provided you with a product devel-
oped for professional use. Your purchase has also contributed to
reducing the burden on the environment and also to the further
development of environmentally adapted electronics products.
Why do we have environmentally labelled computers?
In many countries, environmental labelling has become an established method for encourag-
ing the adaptation of goods and services to the environment. The main problem, as far as
computers and other electronics equipment are concerned, is that environmentally harmful
substances are used both in the products and during the manufacturing. Since it has not been
possible for the majority of electronics equipment to be recycled in a satisfactory way, most
of these potentially damaging substances sooner or later enter Nature.
There are also other characteristics of a computer, such as energy consumption levels, that are
important from the viewpoints of both the work (Internal) and natural (external) environments.
Since all methods of conventional electricity generation have a negative effect on the
environment (acidic and climate-influencing emissions, radioactive waste, etc.), it is vital to
conserve energy. Electronics equipment in offices consume an enormous amount of energy
since they are often left running continuously.
What does labelling involve?
This product meets the requirements for the TCO’99 scheme which provides for international and
environmental labelling of personal computers. The labelling scheme was developed as a joint
effort by the TCO (The Swedish Confederation of Professional Employees), Svenska
Naturskyddsforeningen(TheSwedishSocietyforNatureConservation)andStatensEnergimyndighet
(The Swedish National Energy Administration).
The requirements cover a wide range of issues: environment, ergonomics, usability, emission of
electrical and magnetic fields, energy consumption and electrical and fire safety.
The environmental demands concern restrictions on the presence and use of heavy metals,
brominatedandchlorinatedflameretardants, CFCs(freons)andchlorinatedsolvents, amongother
things. The product must be prepared for recycling and the manufacturer is obliged to have an
environmental plan which must be adhered to in each country where the company implements its
operational policy. The energy requirements include a demand that the computer and/or display,
after a certain period of inactivity, shall reduce its power consumption to a lower level in one or
more stages. The length of time to reactivate the computer shall be reasonable for the user.
Labelled products must meet strict environmental demands, for example, in respect of the reduction
of electric and magnetic fields, physical and visual ergonomics and good usability.
Environmental Requirements
Flame retardants
Flame retardants are present in printed circuit boards, cables, wires, casings and housings. In turn,
they delay the spread of fire. Up to thirty percent of the plastic in a computer casing can consist of
flame retardant substances. Most flame retardants contain bromine or chloride and these are
related to another group of environmental toxins, PCBs, which are suspected to give rise to severe
health effects, including reproductive damage in fisheating birds and mammals, due to the bio-
15
78134641.wpc
17
5/4/99, 5:38 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
TCO’99 cont.
accumulative* processes. Flame retardants have been found in human blood and researchers fear
that disturbances in foetus development may occur.
TCO’99 demand requires that plastic components weighing more than 25 grams must not contain
flame retardants with organically bound chlorine and bromine. Flame retardants are allowed in
the printed circuit boards since no substitutes are available.
Lead**
Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the
nervous system and in higher doses, causes lead poisoning.
TCO’99 requirement permits the inclusion of lead since no replacement has yet been developed.
Cadmium**
Cadmium is present in rechargeable batteries and in the colourgenerating layers of certain
computer displays. Cadmium damages the nervous system and is toxic in high doses.
TCO’99 requirement states that batteries, the colourgenerating layers of display screens and the
electrical or electronics components must not contain any cadmium.
Mercury**
Mercuryissometimesfoundinbatteries, relaysandswitches, Mercurydamagesthenervoussystem
and is toxic in high doses.
TCO’99 requirement states that batteries may not contain any Mercury. It also demands that no
mercuryispresentinanyoftheelectricalorelectronicscomponentsassociatedwiththedisplayunit.
CFCs (freons)
CFCs (freons) are sometimes used for washing printed circuit boards. CFCs break down ozone and
thereby damage the ozone layer in the stratosphere, causing increased reception on Earth of
ultraviolet light with consequent increased risks of skin cancer (malignant melanoma).
TherelevantTCO’99requirement;NeitherCFCsnorHCFCsmaybeusedduringthemanufacturing
and assembly of the product or its packaging.
*Bio-accumulative is defined as substances which accumulate within living organisms.
**Lead, Cadmium and Mercury are heavy metals which are Bio-accumulative.
To obtain complete information on the environmental criteria document, order from:
TCO Development Unit
SE-114 94 Stockholm
SWEDEN
FAX Number: +46 8 782 92 07
E-mail (Internet): [email protected]
You may also obtain current information on TCO’99 approved and labelled products by
16
78134641.wpc
18
5/4/99, 5:38 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
|