Questions?
Do not return product to the store.
We can help Call.
Customer Service Toll-Free 1-800-528-5087
Or visit our website www.murray.com
Dual Stage Snowthrower Model No. 1695720
Connect Shift Rod
DANGER: Amputation Hazard
4
5
1. Connect shift rod (D) to shift lever
(E) and secure with lock washer
(F) and 5/16" hex nut (G). Tighten
hex nut with a 1/2" wrench while
preventing stud (H) from turning
Contact with moving parts inside chute will cause serious injury or death.
Shut off engine before unclogging discharge chute.
Use clean-out tool, not hands!
D
WARNING:
G
F
E
H
4
with a 7/16" wrench.
Failure to read and follow the Operator’s Manuals and all operating instructions
can result in serious injury or death.
Install Chute Rotator Crank
1. Insert chute rotator crank rod (I)
WARNING:
through hole in dash and
sub-
Fuel and its vapors are flammable and explosive. Turn off engine and wait at least
2 minutes before refueling. Let spilled fuel evaporate before starting engine.
dash.
5
I
2. Align small holes before inserting
end of rod into universal bushing
(J).
Remote Deflector Control
Crank
3. Push straight side of hair pin (K)
through both small holes until it
6
clicks into place.
Traction Drive Lever
Remove Snowthrower
From Crate
K
Speed Select Lever
6
1. Cut straps from between
snowthrower and wood pallet by
wheels and auger.
Auger Drive Lever
J
Snow Chute Deflector
2. Roll snowthrower off crate.
Check the Cables
L
7
8
Fuel Cap
1. If control cables have become
unattached from motor mount
frame, reconnect traction drive
cables (L) and auger drive cables
M
Oil Dipstick
Clean-Out Tool
7
(M).
Note: The cables were adjusted at the
You Will Need:
factory and no adjustments should be
necessary. However, after the handles
are put in the operating position, the
cables can be to tight or too loose.
• Utility knife
• Unleaded fuel
• Tire pressure gauge
• 1/2" combination or deep socket wrench
• 7/16" wrench
If an adjustment is necessary see
“Check and Adjust the Cables” in
the MAINTENANCE section of the
Operator’s manual.
Make sure you have all items before assembly.
• 5/16” Flange Lock Nuts, 2
• Ignition Keys, 2 (1 pre-attached to snowthrower)
• 5/16” Hex Nut, 1
Height Adjust Skid
Assemble the Drift Cutter
Drift cutters are used to cut a path
through snow deeper than the auger
housing.
O
P
• Extra Shear Pins, 2
• Extra Cotter Pins, 2
• Chute Rotator Crank, 1
• Operator’s Manual—Engine
• Operator’s Manual—Product
• Illustrated Parts List
• Hair Pin, 1
• Zip Ties, 2
• 5/16” Lock Washer, 1
1. On each side of auger housing (N),
• Carriage Bolts, 2
insert carriage bolt (P) through
• 120V Power Cord, 1
upper hole.
8
N
• Product Registration Card
2. Insert lower tab of drift cutter into
lower hole.
Note: “Right” and “Left” are from the Operating Position.
3. Secure with wing nuts.
Secure Cables and Final Checks
Raise Handles and
Check Cables
1. Cut orange zip ties that secure
control cables to handle assembly.
Be careful not to cut or damage the
control cables.
1
1. To prevent wires and chute
deflector cable from contacting
tire, secure with zip ties to right
handle just below dash (Q) and
9
10
T
Q
R
S
9
below bend (R).
2. Reduce tire pressure to 14 PSI.
(Tires are over-inflated for shipping
purposes.)
A
2. Rotate upper handle assembly (A)
1
up.
3. Slide carriage bolts (B) and 5/16”
flange lock nuts (C) into lower holes.
DO NOT TIGHTEN AT THIS TIME.
2
3. Check that clean-out tool is attached
to snowthrower. (See assembled
figure.)
Always use a clean-out tool to clear
clogged discharge chute. NEVER use
your hands.
4. Remove shipping tape from control
levers. Make sure the “Z” bend
ends of the control lever cables are
secured in the holes on the control
Check Oil Level and Add Fuel
3
levers as shown.
2
3
WARNING: Fuel and its vapors are flammable and explosive. Turn off engine and wait at
5. Check that all cables can move
freely and are not kinked.
least 2 minutes before refueling. Let spilled fuel evaporate before starting engine.
Note: Engine is shipped with oil. See Engine Manual for complete engine oil
specifications and maintenance requirements.
Notice: Do not use E22 or E85 fuel.
Notice: Do not mix oil with fuel.
C
6. Tighten upper and lower nuts in
handle with a 1/2” wrench or deep
2
socket wrench.
B
B
1. Remove oil dipstick (T). Check oil level. Oil level should be between FULL and ADD marks.
10
Reinstall oil dipstick.
Read Manuals Before Starting Engine
Follow procedures and safety instructions in Operator’s Manuals.
DANGER: Amputation hazard
Contact with moving parts inside chute will cause serious injury or death.
Shut off engine before unclogging discharge chute. Use clean-out tool, not hands!
WARNING: Failure to read and follow the Operator’s Manuals and all operating instructions
can result in serious injury or death.
Copyright © 2009. All rights reserved. No part of this material may be reproduced or transmitted in any form by any means without the
express written permission of Briggs & Stratton Power Products Group, LLC.
Every effort has been made to ensure that the information in this document is accurate and current.
However, we reserve the right to change, alter or otherwise improve the product and this document at any time without prior notice or
obligation.
1738370
Rev.: -
Rev. Date: 04/09
Download from Www.Somanuals.com. All Manuals Search And Download.
|