OPERATION AND PARTS MANUAL
MODEL QP-2TZ
TRASH PUMP
(Diesel Engine)
Revision #0 (03/25/05)
THIS MANUAL MUST ACCOMPANY
THE EQUIPMENT AT ALLTIMES.
Download from Www.Somanuals.com. All Manuals Search And Download.
HERE'S HOW TO GET HELP
PLEASE HAVETHE MODEL AND SERIAL
NUMBER ON-HANDWHEN CALLING
MULTIQUIP CORPORATE OFFICE
18910 Wilmington Ave.
Carson, CA 90746
800-421-1244
FAX:310-537-3927
Email: mq@multiquip.com
Internet:www.multiquip.com
PARTS DEPARTMENT
800-427-1244
310-537-3700
FAX:800-672-7877
FAX:310-637-3284
MAYCO PARTS
800-306-2926
310-537-3700
FAX:800-672-7877
FAX:310-637-3284
SERVICE DEPARTMENT
800-421-1244
FAX:310-537-4259
310-537-3700
TECHNICAL ASSISTANCE
800-478-1244
FAX:310-631-5032
FAX:310-537-1173
WARRANTYDEPARTMENT
800-421-1244,EXT.279
310-537-3700,EXT.279
© COPYRIGHT 2004, Multiquip INC.
Multiquip Inc, the MQ logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written
permission. All other trademarks are the property of their respective owners and used with permission.
This manual MUST accompany the equipment at all times.This manual is considered a permanent part of the equipment and should
remain with the unit if resold.
The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations are
based on the MQ Model QP-2TZTrash Pump. Illustrations, descriptions, references and technical data contained in this manual are
for guidance only and may not be considered as binding. Multiquip Inc. reserves the right to discontinue or change specifications,
design or the information published in this publication at any time without notice and without incurring any obligations.
To find the latest revision of this
publication, visit our website at:
QP-2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05) — PAGE 3
Download from Www.Somanuals.com. All Manuals Search And Download.
QP-2TZ — TABLE OF CONTENTS
MQ QP-2TZ Trash Pump
Hatz 1B20 Diesel Engine
Spare Parts Kit Assembly ................................. 32-33
Accessories Assembly...................................... 34-35
Crankcase and Engine Mount Assembly ......... 36-37
Crankshaft Assembly ....................................... 38-39
Camshaft Assembly ......................................... 40-41
Piston Assembly............................................... 42-43
Cylinder Head Assembly .................................. 44-45
Oil Pump/Governor Assembly .......................... 46-49
Timing Cover Assembly ................................... 50-51
Flywheel Assembly........................................... 52-53
Fuel Injection Assembly ................................... 54-57
Recoil Starter Assembly ................................... 58-59
Air Duct Assembly ............................................ 60-63
Crankcase Breather Assembly......................... 64-65
Fuel Tank Assembly ......................................... 66-67
Air Filter Assembly ........................................... 68-69
Muffler Assembly.............................................. 70-71
Sealing and Bonding Adhesives............................ 72
Here’s How To Get Help ............................................ 3
Table of Contents ...................................................... 4
Parts Ordering Procedures ....................................... 5
Safety Message Alert Symbols .............................. 6-7
Rules For Safe Operation ...................................... 8-9
Pump Specifications/Dimensions .............................10
Engine Specifications ...............................................11
General Information .................................................12
Pump Components ..................................................13
Refueling ..................................................................14
Basic Engine ............................................................15
Pre-Inspection (Engine) ...........................................16
Pre-Setup (Pump) ....................................................17
Initial Start-up (Engine) ............................................18
Maintenance (Pump) ......................................... 19-20
Maintenance (Engine)........................................ 21-22
Preparation for Long-Term Storage.........................23
Troubleshooting (Engine).........................................24
Troubleshooting (Pump)...........................................25
Explanation Of Code In Remarks Column ...............26
Suggested Spare Parts ............................................27
Pump Assy. ........................................................ 28-31
Terms and Condition Of Sale
—
Parts .................. 73
Specification and part number
are subject to change without
notice.
PAGE 4 — QP- 2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS ORDERING PROCEDURES
When ordering parts,
please supply the following information:
❒
❒
❒
❒
❒
❒
❒
Dealeraccountnumber
Dealernameandaddress
Shipping address (if different than billing address)
Returnfaxnumber
Applicable model number
Quantity,part number and description of each part
Specifypreferredmethodofshipment:
✓
✓
✓
✓
✓
✓
FedEx or UPS Ground
FedEx or UPS Second Day or Third Day
FedEx or UPS Next Day
Federal Express Priority One
DHL
Note:Unlessotherwiseindicatedbycustomer, all
orders are treated as “Standard Orders”, and will
ship within 24 hours.We will make every effort to ship
“Air Shipments” the same day that the order is
received, if prior to 2PM west coast time. “Stock
Orders” must be so noted on fax or web forms.
Truck
Place Your Parts Order Via Web or Fax
For Even More Savings!
Here’s how to get help...
Please have the model and serial number
on hand when calling.
(Domestic USA Dealers Only)
MULTIQUIP CORPORATE OFFICE
18910 Wilmington Ave.
Carson, CA 90746
Email: mq@multiquip.com
800-421-1244
FAX: 310-537-3927
Extra Discounts!
All parts orders which include complete part numbers and
are received by our automated web parts order system, or
by fax qualify for the following extra discounts:
Ordered
via
Standard
orders
Stock orders
PARTS DEPARTMENT
800-427-1244
310-537-3700
MAYCO PARTS
800-306-2926
310-537-3700
SERVICE DEPARTMENT
800-421-1244
310-537-3700
TECHNICAL ASSISTANCE
800-478-1244
WARRANTY DEPARTMENT
800-421-1244, EXT. 279
310-537-3700, EXT. 279
($750 list and above)
FAX: 800-672-7877
FAX: 310-637-3284
Fax
3%
5%
10%
10%
Web
FAX: 800-672-7877
FAX: 310-637-3284
Special freight allowances
when you order 10 or more
line items via Web or Fax!**
FedEx Ground Service at no charge for freight
No other allowances on freight shipped by any other carrier.
FAX: 310-537-4259
FAX: 310-631-5032
FAX: 310-537-1173
**Common nuts, bolts and washers (all items under $1.00
list price) do not count towards the 10+ line items.
NOTE:DISCOUNTSARESUBJECTTOCHANGE
MULTIQUIP INC.
Direct TOLL-FREE access
to our Parts Department:
18910WILMINGTON AVENUE
POST OFFICE BOX 6254
CARSON, CALIFORNIA 90749
310-537-3700 • 800-421-1244
FAX:310-537-3927
Toll-free nationwide — 800-427-1244
INTERNET:www.multiquip.com
Toll-free FAX — 800-6-PARTS-7 (800/672-7877)
QP-2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05) — PAGE 5
Download from Www.Somanuals.com. All Manuals Search And Download.
QP-2TZ — SAFETY MESSAGE ALERT SYMBOLS
FORYOUR SAFETY ANDTHE SAFETY OF OTHERS!
HAZARD SYMBOLS
Safety precautions should be followed at all times when operating
this equipment. Failure to read and understand the Safety
Messages and Operating Instructions could result in injury to
yourself and others.
Lethal Exhaust Gases
Engine exhaust gases contain poisonous
This Owner's Manual has been
developed to provide complete
instructions for the safe and efficient
operation of the Multiquip Model
carbon monoxide. This gas is colorless and
odorless, and can cause death if inhaled.
NEVER operate this equipment in a confined
area or enclosed structure that does not
provide ample free flow air.
QP-2TZ Trash Pump. Refer to the
engine manufacturers instructions for
data relative to its safe operation.
Before using this pump, ensure
that the operating individual has
read and understands all
instructions in this manual.
Explosive Fuel
GASOLINE is extremely flammable, and its
vapors can cause an explosion if ignited. DO
NOT start the engine near spilled fuel or
combustible fluids. DO NOT fill the fuel tank
while the engine is running or hot. DO NOT
overfill tank, since spilled fuel could ignite if it
comes into contact with hot engine parts or
sparks from the ignition system. Store fuel in
approved containers, in well-ventilated areas
and away from sparks and flames. NEVER
SAFETY MESSAGE ALERT SYMBOLS
The three (3) Safety Messages shown below will inform you
about potential hazards that could injure you or others. The
Safety Messages specifically address the level of exposure to
the operator, and are preceded by one of three words: DANGER,
WARNING, or CAUTION.
DANGER
Burn Hazards
You WILL be KILLED or SERIOUSLY INJURED
if you DO NOT follow these directions.
Engine components can generate extreme heat.
To prevent burns, DO NOT touch these areas
while the engine is running or immediately after
operations. Never operate the engine with heat
shields or heat guards removed.
WARNING
You CAN be KILLED or SERIOUSLY INJURED if
you DO NOT follow these directions.
Rotating Parts
CAUTION
You CAN be INJURED if you DO NOT follow
NEVER operate equipment with covers, or
guards removed. Keep fingers, hands, hair and
clothing away from all moving parts to prevent
injury.
these directions.
Potential hazards associated with the QP-2TZ Trash Pump
operation will be referenced with Hazard Symbols which appear
throughout this manual, and will be referenced in conjunction
with Safety Message Alert Symbols.
PAGE 6 — QP- 2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
QP-2TZ — SAFETY MESSAGE ALERT SYMBOLS
Accidental Starting
Respiratory Hazard
ALWAYS place the engine ON/OFF switch in
the OFF position when the pump is not in use.
ALWAYS wear approved respiratory
protection.
Equipment Damage Messages
Sight and Hearing hazard
Other important messages are provided throughout this manual
to help prevent damage to your pump, other property, or the
surrounding environment.
ALWAYS wear approved eye and hearing
protection.
This pump, other property, or the
surrounding environment could be
damaged if you do not follow
instructions.
QP-2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05) — PAGE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
RULES FOR SAFE OPERATION
■
NEVER touch the hot exhaust manifold,
muffler or cylinder.Allow these parts to cool
before servicing engine or pump.
DANGER
Failure to follow instructions in this manual may lead to
serious injury or even death! This equipment is to be
operated by trained and qualified personnel only! This
equipment is for industrial use only.
The following safety guidelines should always be used when
operating the trash pump:
■
■
HighTemperatures – Allow the engine to cool before adding
fuel or performing service and maintenance functions. Contact
with hot components can cause serious burns.
GENERAL SAFETY
■
DO NOT operate or service this equipment before
readingthisentiremanual.
The engine of this pump
requires an adequate
free flow of cooling air.
NEVER! operate the
pump in any enclosed or
narrow area where free
flow of the air is
restricted. If the air flow
is restricted it will cause
■
■
This equipment should not be operated by persons under 18
years of age.
NEVER operate this equipment without proper protective
clothing, shatterproof glasses, steel-toed boots and other
protective devices required by the job.
serious damage to the
pump or engine and may cause injury to people and property.
Remember the pump's engine gives off DEADLY gases.
■
■
NEVER operate this equipment when not feeling
■
■
ALWAYS refuel in a well-ventilated area, away from sparks
well due to fatigue, illness or taking medicine.
and open flames.
ALWAYS use extreme caution when working with flammable
liquids. When refueling, stop the engine and allow it to cool.
DO NOT smoke around or near the machine. Fire or explosion
could result from fuel vapors, or if fuel is spilled on a hot
engine.
NEVER operate this equipment under the influence or drugs or
alcohol.
■
NEVER operate the pump in an explosive
atmosphere or near combustible
materials. An explosion or fire could result
causing severe bodily harm or even
death.
■
■
■
Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.
ALWAYS check the machine for loosened threads or bolts
before starting.
■
■
■
Topping-off to filler port is dangerous, as it
tends to spill fuel.
ALWAYS wear proper respiratory (mask) hearing and eye
protection equipment when operating the pump.
Refer to the Engine Owner's Manual for engine technical
questions or information.
NEVER use accessories or attachments, which are not
recommended by Multiquip for this equipment. Damage to
the equipment and/or injury to user may result.
■
Manufacturer does not assume responsibility for any accident
due to equipment modifications.
PAGE 8 — QP- 2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
RULES FOR SAFE OPERATION
■
■
■
■
NEVER Run engine without air cleaner. Severe engine
■
■
High Temperatures – Always stop engine and allow the
engine to cool before adding fuel, oil or performing service
and maintenance functions. Contact with hot components can
cause serious burns.
damage may occur.
ALWAYS read, understand, and follow procedures in
Operator’s Manual before attempting to operate equipment.
NEVER disconnect any "emergency or safety devices".
These devices are intended for operator safety. Disconnection
of these devices can cause severe injury, bodily harm or even
death! Disconnection of any of these devices will void all
warranties.
ALWAYS be sure the operator is familiar with proper safety
precautions and operation techniques before using pump.
ALWAYS store equipment properly when it is not being used.
Equipment should be stored in a clean, dry location out of the
reach of children.
Maintenance Safety
■
■
■
■
NEVER leave the pump unattended, turn off engine when
unattended.
NEVER lubricate components or attempt service on a running
machine.
Unauthorized equipment modifications will void all
warranties.
■
ALWAYS allow the machine a proper amount of time to cool
before servicing.
NEVER pump volatile, explosive, flammable or low flash
point fluids.These fluids could ignite or explode.
■
■
Keep the machinery in proper running condition.
Fix damage to the machine immediately and always replace
broken parts, or missing decals.
■
■
NEVER operate the pump in an explosive atmosphere.
Before starting the pump, check that the clean-out cover is
securely fasten.
■
■
■
Dispose of hazardous waste properly.Examples of potentially
hazardous waste are used motor oil, fuel and fuel filters.
■
■
ALWAYS ensure pump is on level ground before use.
DO NOT use food or plastic containers to dispose of
hazardous waste.
Become familiar with the components of the pump before
operating.
DO NOT pour waste, oil or fuel directly onto the ground,
down a drain or into any water source.
■
NEVER pump corrosive chemicals or water containing toxic
substances. These fluids could create serious health and
environmental hazards. Contact local authorities for
assistance.
Emergencies
■
ALWAYS know the location of the
nearest fire extinguisher.
■
NEVER open the priming plug when pump is hot. Hot water
inside could be pressurized much like the radiator of an
automobile. Allow pump to cool to the touch before loosening
plug.
■
■
ALWAYS know the location of the nearest
first aid kit.
■
■
NEVER open the pump housing during operation or start the
pump with the clean-out cover removed.The rotating impeller
inside the pump can cut or sever objects caught in it.
In emergencies always know the location of the
nearest phone or keep a phone on the job site.
Also know the phone numbers of the nearest
ambulance, doctor and fire department. This
information will be invaluable in case of an
emergency.
NEVER block or restrict flow from discharge hose. Remove
kinks from discharge line before starting pump. Operation
with a blocked discharge line can cause water inside pump
to overheat.
■
■
ALWAYS fill the pump casing with water before starting the
engine. Failure to maintain water inside the pump housing
will cause severe damage to the pump.
In winter drain water from pump housing to prevent freezing.
QP-2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05) — PAGE 9
Download from Www.Somanuals.com. All Manuals Search And Download.
QP-2TZ — SPECIFICATIONS/DIMENSIONS (PUMP)
Table 1. Specifications (Pump)
Model
QP-2TZ
Type
Trash Pump
Suction & Discharge Size
2.00 in. (50 mm.)
Maximum Pumping
Capacity
198 gallons/minute
(750 liters/minute)
Pump
Max. Solids Diameter
Max. Lift
1.50 in. (25.4 mm.)
25 ft. (7.62 meters)
95 ft. (29.0 meters)
Max. Head
Dimension
(L x W x H)
26.5 x 18.3 X 23.2 in.
(67.5 X 46.5 X 59.0 cm.)
Dry Net Weight
131 lbs. (59.5 Kg.)
18.3 IN.
(46.5 CM.)
23.2 IN.
(59 CM.)
26.5 IN.
(67.5 CM.)
Figure 1. QP-2TZ Dimensions
PAGE 10 — QP- 2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
QP-2TZ — SPECIFICATIONS (ENGINE)
Table 2. Engine Specifications (HATZ 1B20)
HATZ Diesel
Model 1B20
Air-Cooled
No.
Cylinders
Displacement
Idle
Speed
Lube Oil
Capacity
Type Air
Cleaner
Starting
Method
Weight
1
14.5 in3
(.232 liters)
0.95 qts.
(0.9 liters)
Dry
Element
Recoil
Start
72 lbs.
(33 kg.)
800 RPM
CCMC - D4 - D5 - PD@ or API - CD-
CE - CF -CG or SHPD
Engine Oil
Type
EN 590 - DIN 51601 BS 2869 A1/A2-
ASTM D 975-1D/2D
Type Fuel
110
100
90
80
70
60
50
40
30
20
10
TOTAL
HEAD
FT.
1.6 FT.
16.7 FT.
10.0 FT.
3.3 FT.
23.3 FT.
0
0
100
150
200
50
US GALLONS PER MINUTE
QP-2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05) — PAGE 11
Download from Www.Somanuals.com. All Manuals Search And Download.
QP-2TZ — GENERAL INFORMATION
Elevation
APPLICATION
Higher elevations will effect the performance of the pump. Due to
less atmospheric pressure at higher altitudes, pumps DO NOT
have the priming ability that they have at sea level.This is due to
the “thinner air” or lack of oxygen at higher altitudes.
The QP-2TZ Trash Pump is designed to be used for dewatering
applications. Both the suction and discharge ports on the
QP-2TZ trash pump use a 2-inch diameter opening, which
allows the pump to pump at a rate of approximately 211 gallons/
minute (gpm) or 800 liters/minute (lpm).
A general rule of thumb is that for every 1,000 feet of elevation
above sea level a pump will lose one foot of priming ability.
Trash or self-priming pumps are designed to purge air from the
suction line and create a partial vacuum in the pump body.The
reduced atmospheric pressure inside the pump allows water to
flow through the suction line and into the pump body. The
centrifugal force created by the rotating impeller pressurizes the
water and expels it from the pump.
For example, in Flagstaff, Arizona where the elevation is
approximately 7,000 feet, the pump would have a suction lift of
25 feet rather than the 18 feet at sea level.Table 3 shows suction
lift at various elevations.
Engine
Table 3. Suction Lift at Various Elevations
This trash pump is powered by a 4.6 horsepower, air-cooled,
HATZ 1B20 diesel engine.
Altitude
Suction Lift in Feet (Meters)
Feet (Meters)
Trash Pump
Sea Level
10.0 (3.048) 15.0 (4.572) 20.0 (6.096) 25.0 (7.620)
8.80 (2.680) 13.2 (4.023) 17.6 (5.364) 22.0 (6.705)
7.80 (2.377) 11.7 (3.566) 15.6 (4.754) 19.5 (5.943)
6.90 (2.103) 10.4 (3.169) 13.8 (4.206) 17.3 (5.273)
6.20 (1.889) 9.30 (2.834) 12.4 (3.779) 15.5 (4.724)
Trash pumps derive their name from their ability to handle a
greater amount of debris and solids than standard centrifugal
pumps.This pump generally handle solids up to 1/2 the size of
the discharge opening making them less likely to clog. Also trash
pumps are capable of handling water with 25% solids by weight.
2,000 (610)
4,000 (1,219)
6,000 (1,829)
8,000 (2,438)
The advantage of using a trash pump is that it can be quickly and
easily disassembled in the field "without tools" and easily
cleaned when clogged.
10,000 (3,048) 5.70 (1.737) 8.60 (2.621) 11.4 (3.474) 14.3 (4.358)
Table 4 shows percentage drops in performance as elevation
increases.
Suction Lift
This pump is intended to be used for dewatering applications
and is capable of suction lifts up to 25 feet at sea level. For
optimal suction lift performance, keep the suction hose or line as
short as possible. In general, always place the pump as close to
the water as possible.
Table 4. Performance Loss at Various
Elevations
Altitude
Discharge Flow Discharge Head
Feet (Meters
Pump Support
The pump should always be placed on solid stationary ground
in a level position.
Sea Level
100%
97%
95%
93%
91%
88%
100%
95%
91%
87%
83%
78%
2,000 (610)
NEVER place the pump on soft soil. The suction hose or pipe
connection should always be checked for tightness and leaks. A
small suction leak in the hose or fittings could prevent the pump
from priming.
4,000 (1,219)
6,000 (1,829)
8,000 (2,438)
10,000 (3,048)
PAGE 12 — QP- 2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
QP-2TZ — PUMP COMPONENTS
Figure 2 shows a typical application using the QP-2TZ Trash pump. Please note that this pump is intended for the removal of clean
water and water containing some debris and solids. Maximum size of solids should not exceed 1.0 inch (25 mm) in diameter. DO
NOT set strainer on bottom of water bed. Placing the strainer above the water bed will prevent the pump from drawing in excessive
amounts of sand and foreign debris.
Figure 2.
1. Pump –The model QP-2TZ is a 2-inch trash pump used 6. Suction Port – Connect a 2-inch inlet hose to this port.
in general dewatering applications. Typical dewatering
applications consist of manholes, septic tanks, fast and
slow seepage ditch water, silt water, mud water and muck
water.
Use two worm clamps to secure the hose.
7. Suction Hose – Connect this flexible rubber hose to the
suction portion the pump. Make sure that the hose lays flat
and is not kinked. Use only recommended type suction
hose. Contact Multiquip Parts Department for ordering
information.
2. Fill Cap – Prior to operation, the pump casing should be
filled with water.Remove this cap to add water to the pump.
After the initial prime, a sufficient amount of water will be
retained in the casing so that the operator will not need to
re-prime later.
8. Clean-out Cover Handles –To gain access to the pump's
clean-out area, grip both handles, then pull to remove cover.
Make sure both locking knobs have been released before
attempting to remove clean-out cover.
If the casing is dry or has insufficient water, the pump will
have difficulty in priming which could lead to premature
mechanical seal wear thus causing damage to the pump.
9. Drain Plug – Remove this plug to drain water from the
pump.
3. Discharge Port – Connect a 2-inch discharge hose to this
10. Clean-out Cover – Remove cover to gain access to the
port.
clean-out area.
4. Worm Clamp – Used to secure the hose to the inlet and
outlet ports on the pump. Use two clamps to secure the
hose on the inlet side of the pump.
11. Locking Knobs – Turn both knobs clockwise to secure
clean-out cover, turn counterclockwise to release cover.
12. Strainer – Always attach a strainer to the bottom side of
the suction hose to prevent large objects and debris from
entering the pump. Strainer should be positioned so that it
will remain completely under water.Running the pump with
the strainer above water for long periods can damage pump.
5. Discharge Hose – Connect this flexible rubber hose to
the discharge port on the pump. Make sure that the hose
lays flat and is not kinked. Use only recommended type
discharge hose. Contact Multiquip Parts Department for
ordering information.
QP-2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05) — PAGE 13
Download from Www.Somanuals.com. All Manuals Search And Download.
QP-2TZ — REFUELING
DANGER
Adding fuel to the tank should be done only when
the engine is stopped and has had an opportunity to
cool down. In the event of a fuel spill, DO NOT attempt to start the
engine until the fuel residue has been completely wiped up, and the
area surrounding the engine is dry. If pump is placed in a truck bed
with a plastic liner, REMOVE pump from truck bed and place on
ground (Figure 3) to refuel. The possibility of fire or explosion
exists, due to static electricity.
PLASTIC
TRUCK-BED
LINER
DANGER
DO NOT ADD FUEL
TO TRASH PUMP IF
TRASH PUMP IS PLACED
INSIDE TRUCK-BED WITH
PLASTIC LINER. POSSIBILITY EXISTS
OF EXPLOSION OR FIRE DUE TO
STATIC ELECTRICITY.
Figure 3. Pump Refueling
PAGE 14 — QP- 2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
QP-2TZ — BASIC ENGINE
Figure 4. Engine Controls and Components
INITIAL SERVICING
6.
7.
Engine Motor Mounts – Attach these engine mounts to
The engine (Figure 4) must be checked for proper lubrication and
filled with fuel prior to operation. Refer to the manufacturer’s Engine
manual for instructions & details of operation and servicing.
the pump frame.Tighten securely.
Oil Filter – Remove this bolt to gain access (internal) to the
engine oil filter.Service the oil filter as recommended in the
maintenance section of this manual.
1. Fuel Filler Cap/FuelTank – Pull this latch to add diesel
fuel to the tank. After refueling, always make sure the fuel
cap is latched properly. DO NOT over fill. For additional
information refer to engine owner's manual.
8.
9.
Oil Drain Plugs – There are two oil drain plugs, one is
underneath the flywheel, the other on the side of the engine.
Remove these plugs to drain engine oil from the engine
crankcase.
WARNING
Crankshaft – Connect this shaft to the input of the
transmission.
Adding fuel to the tank should be accomplished only
when the engine is stopped and has had an
opportunity to cool down. In the event of a fuel spill,
DO NOT attempt to start the engine until the fuel
residue has been completely wiped up, and the area surrounding
the engine is dry.
10. Muffler – Used to reduce noise and emissions.
11. Nameplate – Contains information about the engine.
WARNING
2. Engine Lifting Straps/Cover – Remove the air cleaner
cover, then lift this cover (the one with decals on it) to gain
access to the engine lifting straps.
Engine components can generate extreme heat.
To prevent burns, DO NOT touch these areas
while the engine is running or immediately after operating. NEVER
operate the engine with the muffler removed.
3. Air Cleaner/Cover – Prevents dirt and other debris from
entering the fuel system. Remove wing-nut on side of air
filter cover to gain access to filter element.
Operating the engine without an
air filter, with a damaged air filter,
or a filter in need of replacement
will allow dirt to enter the engine,
causing rapid engine wear.
4. Speed Control Lever – This lever is connected to the
throttle control which is located on the side of the engine
compartment cover. Use this lever to control engine speed.
5.
Dip Stick – Remove dipstick to determine if the engine oil
level is low. If low add oil as specified.
QP-2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05) — PAGE 15
Download from Www.Somanuals.com. All Manuals Search And Download.
QP-2TZ — PRE-INSPECTION (ENGINE)
3. Insertandremovethedipstickwithoutscrewingitintothefiller
neck. Check the oil level shown on the dipstick.
CAUTION
4. If the oil level is low (Figure 6), fill to the edge of the oil filler
holewiththerecommendedoiltype(Table5).Maximum oil
capacity is 1.16 quarts (1.1 liters)
NEVER operate the pump in a confined
area or enclosed area structure that does
not provide ample free flow of air.
ALWAYS wear approved eye and hearing
protection before operating the pump.
Before Starting
1.
Read safety instructions at the
beginning of manual.
2.
Clean the pump, removing dirt and
dust, particularly the engine
cooling air inlet, carburetor and air
cleaner.
Figure 6. Engine Oil Dipstick (Oil Level)
Table 5. Oil Type
3.
4.
5.
Check the air filter for dirt and dust. If air filter is dirty, replace
air filter with a new one as required.
Season
Summer
Spring/Fall
Winter
Temperature
25°C or Higher
25°C~10°C
Oil Type
SAE 10W-30
SAE 10W-30/20
SAE 10W-10
Check carburetor for external dirt and dust. Clean with dry
compressed air.
Check fastening nuts and bolts for tightness.
0°C or Lower
Engine Oil Check
1.
To check the engine oil level, place the pump on secure
level ground with the engine stopped.
Explosive Fuel
2.
Remove the filler dipstick from the engine oil filler hole
(Figure 5) and wipe clean.
DANGER
Motor fuels are highly flammable and can be dangerous if
mishandled. DO NOT smoke while refueling. DO NOT attempt
to refuel the pump if the engine is hot! or running.
Fuel Check
1. Remove the gasoline cap located on top of fuel tank.
2. Visually inspect to see if the fuel level is low. If fuel is low,
replenish with unleaded fuel.
Figure 5. Engine Oil Dipstick (Removal)
3. When refueling, be sure to use a strainer for filtration. DO
NOT top-off fuel. Wipe up any spilled fuel immediately!
PAGE 16 — QP- 2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
QP-2TZ — PRE-SETUP (PUMP)
Before Starting
Suction and discharge hoses are
NOTE
1. Read safety instructions at the
beginning of manual.
available from Multiquip. Contact
your nearest dealer for more
information.
2. Place pump as near to water as
possible,onafirmflat,levelsurface.
5. The discharge hose is usually a collapsible (thin-walled)
hose, however if a thin-walled discharge hose is not avail-
able, a rigid suction hose can be substituted in its place.
3. Toprimepump,removefillcap(Figure2)andfillpumpcasing
with water.If the pump casing is not filled with water before
starting, it will not begin pumping.
6. Make sure the suction strainer (Figure 2) is clean and
securely attached to the water end of the suction hose. The
strainer is designed to protect the pump by preventing large
objects from being pulled into the pump.
CAUTION
Pump casing must be filled with water before using pump.
Otherwise pump will not be able to begin pumping.
CAUTION
The strainer should be positioned so it will remain completely
under water. Running the pump with the strainer above water
for long periods can damage the pump.
WARNING
DO NOT open fill cap if pump is hot! Water inside may be
under pressure.
CAUTION
DO NOT pump flammable fluids, corrosive chemicals or fluids
containing toxic substances. These fluids can create potentially
dangerous health and environmental hazards. Contact local
authorities for assistance.
4. Checkforleaksbetweenpumpandengine.Ifwaterisleaking
between the pump and engine housing, the seal inside the
pumpmaybewornordamaged.Continued operationofthe
pumpisnot recommended.Furtherusageofthe pumpunder
theseconditionsmaycauseseverewaterdamagetoengine.
Hoses and Clamps
1. Check that all hoses are securely attached to the pump.
Make certain suction hose (Figure 2) does not have any air
leakage.Tighten hose clamps and couplings as required.
CAUTION
This pump uses a water-cooled mechanical seal to prevent
water from seeping into the engine. The passage of water
through the pump casing lubricates the seal and prevents it
from overheating. NEVER! operate the pump without water in
the casing as this will cause damage to the mechanical seal.
2. Itisrecommendedthat 2 clampsbeusedwhensecuringthe
suction hose to the inlet side (suction) of the pump.
3. Remember suction hoses must be rigid enough not to
collapse when the pump is in operation.
4. Check that the discharge hose (Figure 2) is not restricted.
Place hose so that it lays as straight as it is possible on the
ground. Remove any twists or sharp bends from hose which
may block the flow of water.
QP-2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05) — PAGE 17
Download from Www.Somanuals.com. All Manuals Search And Download.
QP-2TZ — INITIAL START-UP (ENGINE)
CAUTION
Do not allow the starter grip to snap back against the engine.
Return it gently to prevent damage to the starter.
CAUTION
DO NOT attempt to operate the pump
until the Safety, General Information and
Inspection sections of this manual have
been
read
and
thoroughly
understood.
5.
6.
Pull the starter grip again, hard and fast, pulling it all the
way out to start engine.
This section is intended to assist the operator with the initial
start-up of the trash pump. It is extremely important that this
section be read carefully before attempting to use the pump in
the field.
If the engine does not start, repeat steps 4 and 5.
CAUTION
ALWAYS run engine at full speed while pumping.
Starting the Engine (HATZ engine)
3.
Move the engine speed lever to the START position
(Figure 8).
Stopping The Engine
Normal Shutdown
1. Move the engine speed lever to the low speed and run the
engine for about three minutes with no load.
2. After the engine cools, move the engine speed lever to the
STOP position (Figure 11).
Figure 8. Engine Speed Lever (START position)
4. Grasp the starter grip (Figure 9) and slowly pull it out until
you feel the strongest resistance then return the starter grip
to the initial position.
Figure 11. Engine Speed Lever (STOP Position)
4. Slowlypullthestartergrip(Figure9)untilstrongresistance
is felt and leave it in this position. This prevents rust from
forming while the engine is not in use.
CAUTION
When stopping the engine, reduce the load slowly. Do
not stop engine suddenly since it may cause the
temperature to rise abnormally.
Emergency Shutdown
1. Tostopengineimmediately,quicklyplacetheenginespeed
lever to the STOP position.
Figure 9. Starter Grip
PAGE 18 — QP- 2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
QP-2TZ — MAINTENANCE (PUMP)
Pump Vacuum Test
Adjusting Impeller Clearance
1. If it is necessary to replace impeller or volute, be sure
clearance between impeller and volute is adjusted correctly.
CAUTION
DO NOT attempt to start the engine unless the pump has
previously been primed with water. Severe pump damage
will occur if pump has not been primed.
2. The impeller should be as close to the volute as possible
without rubbing against it. Clearance is adjusted by adding
or removing shims from behind the impeller.
3. Check clearance between impeller and insert by slowly
pulling starter rope to turn impeller. Remove spark plug to
make it easier to turn impeller.
To perform the pump vacuum test do the following:
1. Remove the pump fill cap (Figure 2), and fill the pump with
water.
2. Start the engine as outlined in the initial start-up section,
and wait for the pump to begin pumping.
It is important not to remove too
many shims or the clearance
between the impeller and volute will
become too wide and pump
performance will be reduced.
3. As shown in Figure 13, place a water hose inside the
discharge opening of the pump, and turn on the water.This
flow of water into the discharge opening will prevent the
pump from running dry.
Remember as the impeller wears
4. Place the Pump Vacuum Tester (P/N 7000030) over the
pump suction (inlet) opening (Figure 13) with the vacuum
gauge facing upwards. It may be necessary to apply a small
amount of water around the rubber seal of the vacuum tester
to make a good suction fit.
down, additional shims may be required to maintain the
clearance between the impeller and insert.
4. Check the impeller every six months for wear, and for
clearance between the impeller face and the volute. Also
check the shaft seal for wear, as well as the shaft sleeve.
5. Check and make sure that there are no air leaks between
the vacuum tester and the inlet port on the pump. If air leaks
are present reset vacuum tester.
Pump Cleaning
After pumping water containing large amounts of dirt and debris,
perform the following:
6. Run the pump for a few minutes while monitoring the vacuum
gauge. If the gauge indicates a reading between -25 and
-20 in. Hg. (inches of mercury), then it can be assumed that
the pump is working correctly.
1. Remove the drain plug from the pump housing (Figure 2)
and drain any water left in the pump.
2. Loosen the two locking hand knobs (turn counterclockwise)
and remove clean-out cover.
3. Clean and remove dirt, debris from pump casing. Inspect
impeller and volute for wear.Replace any damaged or worn
parts.
25 in. Hg. (inches of mercury)
translates into 25 feet of lift at sea
level.
7. If the vacuum tester gauge indicates a reading below
-20 in. Hg, it can then be assumed that the pump is not
functioning correctly, and corrective action needs to be taken.
CAUTION
The impeller may develop sharp edges. Use extreme care
6. To test the flapper valve, shut down the engine.The vacuum
tester should remain attached to the pump suction inlet port
by vacuum.This indicates the pump's flapper valve is seating
properly to hold water in the suction hose when the engine
is stopped. This prevents backflow and allows for faster
priming when the engine is restarted.
when cleaning around the impeller to prevent being cut.
QP-2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05) — PAGE 19
Download from Www.Somanuals.com. All Manuals Search And Download.
QP-2TZ — MAINTENANCE (PUMP)
y depending on
4 on page 12.
Figure 13. Pump Vacuum Tester
PAGE 20 — QP- 2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
QP-2TZ — MAINTENANCE (ENGINE)
Engine Maintenance
Perform engine maintenance procedures as referenced by
Table 6 below:
Table 6. Engine Maintenance Schedule
FIRST
EVERY
EVERY
EVERY
YEAR
OR
EVERY
2 YEARS
OR
MONTH 3 MONTHS 6 MONTHS
OR
DESCRIPTION (3)
OPERATION
BEFORE
OR
OR
10 HRS.
25 HRS.
50 HRS.
100 HRS.
200 HRS.
CHECK
CHANGE
CHECK
X
Engine Oil
X
X
X
Air Cleaner
CHANGE
X (1)
Re-tighten If
Necessary
All Nuts & Bolts
Cooling Fins
Spark Arrester
Fuel Tank
CHECK
CLEAN
X
X
X
CLEAN
Fuel Filter
CHECK
X
Idle Speed
CHECK-ADJUST
CHECK-ADJUST
CHECK
X (2)
Valve Clearance
Fuel lines
X (2)
Every 2 years (replace if necessary) (2)
(1) Service more frequently when used in DUSTY areas.
(2) These items should be serviced by your service dealer, unless you have the proper tools and are mechanically
proficient. Refer to the HATZ shop manual for service procedures.
(3) For commercial use, log hours of operation to determine proper maintenance intervals.
Reference manufacturer engine
manual for specific servicing
instructions.
QP-2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05) — PAGE 21
Download from Www.Somanuals.com. All Manuals Search And Download.
QP-2TZ — MAINTENANCE (ENGINE)
Maintenance
DANGER
Performtheenginemaintenanceproceduresasindicatedbelow:
DO NOT use gasoline as a cleaning solvent, because that
would create a risk of fire or explosion.
DAILY
■
Thoroughly remove dirt and oil from the engine and control
area.Clean or replace the air cleaner elements as necessary.
Check and retighten all fasteners as necessary. Check the
spring box and bellows for oil leaks. Repair or replace as
needed.
ENGINEAIRCLEANER
1. Loosen the wing nut and detach the cover of the air
cleaner shown in Figure 15.
WEEKLY
■
Remove the fuel filter cap and clean the inside of the fuel
tank.
2. Tapthe element(Figure15)severaltimesonahardsurface
toremovedirt,orblowcompressedair[notexceeding30psi
(207 kPa, 2.1 kgf/cm2)] through the element side. NEVER
washtheelementwithdetergentbecausetheelementisoil-
soakedtype.Replacetheelementwhentheoutputdecreases
or bad exhaust color is noticed.
■
Remove or clean the filter at the bottom of the tank.
ENGINEOIL
1. Drain the engine oil when the oil is warm as shown in
Figure 14.
2. Remove the oil drain bolt and sealing washer and allow
the oil to drain into a suitable container.
3. Replace engine oil with recommended type oil as listed
in Table 5. Engine oil capacity is 0.95 quarts (0.9 liters).
DO NOT overfill.
4. Install drain bolt with sealing washer and tighten se-
curely.
Figure 15. Engine Air Cleaner
Figure 14. Engine Oil (Draining)
PAGE 22 — QP- 2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
QP-2TZ — PREPARATION FOR LONG -TERM STORAGE
z
Pull the recoil starter grip slowly. STOP when it feels
tight. This closes the intake and exhaust valves
(compression position) , and helps prevents rust from
forming.
Pump Storage
For storage of the pump for over 30 days, the following is
required:
z
z
Wipe any oil or dirt that may have accumulated on the
engine.
Remove the drain plug from the pump and drain out any
water left in the housing.
z
z
z
Drain the fuel tank completely.
Run the engine for about 3 minutes and then stop.
Stop the engine. Drain the engine crankcase oil while
the engine is still warm. Fill engine crankcase with fresh
oil.
z
Remove the pump cover and clean the inside of pump
housing. Coat the inside of pump housing with a light
film of oil to reduce corrosion. A spray can of oil works
well for this application.
z
Pull the recoil starter grip (Figure 17) 2 or 3 times. DO
NOT start the engine.
z
z
z
Cover suction and discharge ports with duct tape to
prevent any foreign matter from falling into pump.
Cover pump and engine with plastic covering or
equivalent and store in a clean, dry place.
To protect the water cooled-seals, place one-half pint of
lubricating oil (new or used) through the discharge opening
on the pump and crank the engine several times. This
will prevent excessive corrosion and also keep the
mechanical seal lubricated.
Figure 17. Recoil Starter Grip
QP-2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05) — PAGE 23
Download from Www.Somanuals.com. All Manuals Search And Download.
QP-2TZ — TROUBLESHOOTING (ENGINE)
TABLE 7. ENGINE TROUBLESHOOTING
SYMPTOM
POSSIBLE PROBLEM
Speed control lever is in "STOP" position?
No fuel reaching injection pump?
Defective fuel pump?
SOLUTION
Set speed control lever to "START" position.
Add fuel. Check entire fuel system.
Replace fuel pump.
Fuel filter clogged?
Replace fuel filter and clean tank.
Replace or repair fuel line.
Faulty fuel supply line?
Engine will not start or start is
delayed, although engine can
be turned over.
Check piston, cylinder and valves. Adjust or
repair per engine repair manual.
Compression too low?
Repair or replace injector in accordance with
engine repair manual.
Fuel injector not working correctly?
Oil pressure too low?
Check engine oil pressure.
Comply with cold starting instructions and
proper oil viscosity.
Low starting temperature limit exceeded
Check whether clear (not turbid) fuel emerges
from the fuel line (detach from injection
pump). If the fuel is turbid or separated, warm
up the engine or drain the complete fuel
supply system. Refuel with winter grade diesel
fuel.
Fuel separates has inadequate resistance to
low temperatures?
At low temperatures engine will
not start.
Refill engine crankcase with correct type of oil
for winter environment.
Engine oil too thick?
Fuel filter blocked?
Replace fuel filter.
Engine fires but stops soon as
starter is switched off.
Fuel supply blocked?
Fuel tank empty?
Check the entire fuel system.
Add fuel.
Engine stops by itself during
normal operation.
Fuel filter blocked?
Replace fuel filter.
Fuel tank empty?
Fill with No.2 diesel fuel.
Replace fuel filter.
Fuel filter clogged?
Fuel tank venting is inadequate?
Low engine power, output and
speed.
Ensure that tank is adequately vented.
See engine manual for corrective action.
Speed control lever does not remain in
selected position?
Engine oil level too full?
Air filter blocked?
Correct engine oil level?
Clean or replace air filter.
Adjust valves per engine specification.
See engine manual.
Low engine power output and
low speed, black exhaust
smoke.
Incorrect valve clearances?
Malfunction at injector?
PAGE 24 — QP- 2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
QP-2TZ — TROUBLESHOOTING (PUMP)
TABLE 8. PUMP TROUBLESHOOTING
SYMPTOM
POSSIBLE PROBLEM
Not enough priming water in the housing?
Engine speed too low?
SOLUTION
Add water.
Increase throttle.
Clean strainer.
Strainer plugged?
Suction hose damaged?
Replace or repair hose, and clamps
Check that fittings are tight and properly sealed.
Move pump closer to water.
Air leak at suction port?
Pump does not take on water.
Pump is located too high above water line?
Debris collecting in pump housing?
Clean pump housing.
Adjust clearance by adding shims or replace impeller.
Min. .006" - Max. .020"
Too much distance between impeller and volute.
Water leaking out weep hole between pump and Check condition of mechanical seal and gaskets,
engine?
between pump end and engine housing.
Engine speed too low?
Increase throttle speed.
Pump takes in water, little or no Suction strainer partially plugged?
Clean strainer.
discharge.
Impeller/Volute worn?
Adjust clearance by adding shims or replace
impeller/volute
Tighten, replace or add clamp. (Keep extra seals on
pump)
Fittings/clamps are not sealed properly?
Suction hose leaks at inlet.
Hose diameter is too large?
Use smaller diameter hose or replace hose.
Check pressure, add additional clamp.
Check hose.
Pressure too high?
Discharge does not stay on
coupling.
Hose kinked or end blocked?
Impeller jammed or blocked?
Open pump cover and clean dirt and debris from
inside housing.
Impeller does not turn: pump is
hard to start.
Adjust clearance by removing shim from behind
impeller.
Impeller and volute binding?
Defective engine?
See Engine Owner's Manual.
QP-2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05) — PAGE 25
Download from Www.Somanuals.com. All Manuals Search And Download.
QP-2TZ — EXPLANATION OF CODE IN REMARKS COLUMN
How to read the marks and remarks used in this parts
book.
Items Found In the “Remarks” Column
he contents of this catalog are
ubject to change without notice.
Serial Numbers-Where indicated, this indicates a serial
number range (inclusive) where a particular part is used.
Model Number-Where indicated, this shows that the
corresponding part is utilized only with this specific model
number or model number variant.
Items Found In the “Items Number”Column
All parts with same symbol in the number column, , #,
, belong to the same assembly or kit.
+
, %, or
*
■
If more than one of the same
reference number is listed, the
last one listed indicates newest (or
latest) part available.
PAGE 26 — QP- 2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
QP-2TZ — SUGGESTED SPARE PARTS
QP-2TZTRASH PUMP 1TO 3 UNITS
W/ HATZ IB20
Qty.
P/N
Description
2 ............ KIT2T.................... KIT, MECHANICAL SEAL, O-RINGS
1 ............ 2257040030 .......... IMPELLER
2 ............ 0631211159 .......... FLOODING CAP
3 ............ 50426000 .............. AIR FILTER ELEMENT
1 ........... 01548800 ............ ROPE RECOIL STARTER
1 ............ 01535302 .............. CAP, FUEL TANK
1 ............ 01635200 .............. FUEL FILTER, GAS TANK
Part number on this Suggested
Spare Parts List may supersede/
replace the P/N shown in the text
pages of this book.
QP-2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05) — PAGE 27
Download from Www.Somanuals.com. All Manuals Search And Download.
QP-2TZ — PUMP ASSY.
PUMP ASSY.
PAGE 28 — QP- 2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
QP-2TZ — PUMP ASSY.
PUMP ASSY.
NO.
1
2
3
4
5
6
7
8
PART NO.
PART NAME
QTY.
1
1
1
1
4
1
1
1
2
1
1
4
2
1
4
1
1
1
1
2
1
1
1
1
1
1
1
1
1
2
4
REMARKS
1889100011
1889100020
18890001600014
1889100171
19920002200014
2257040030
1889000132
1889100741
1247100250
1889330410
1992250700
0105090825
07904320200014
1889350351
0105090825
1211390610
0481571950
0489402910
2257214010P002
0481310550
0482200180
22572140200014
0631211159
0631211159
0803442930
0811345443
0852833020
0852853020
0191190525
0141090820
0141090825
CASING
CASING COVER
SUCTION COVER
DRAIN COVER
DRAIN COVER HANDLE
IMPELLER
VOLUTE CASING
SUCTION PLATE
DRAIN COVER SET HANDLE
SUCTION PLATE PACKING
WEAR PLATE
BOLT (CASING COVER), M8 X 25
NIPPLE, NPS2" X NPT2"
CHECK VALVE, NBR+SS400
BOLT (ENGINE), M8 X 25
CASING COVER PACKING, OIL SHEET, X 84
O’RING (DRAIN COVER), G195
O’RING (CASING)
BASE, SS400
O’RING (NIPPLE), G55
O’RING (MECHANICAL SEAL SLEEVE), S18
ENGINE BASE, SS400
FLOODING CAP, PF1 1/2"
DRAIN CAP, PF1 1/2"
9
10
11
12
13
14
15
16
17
*
18
*
19
20
21
22
23
24
*
25
MECHANICAL SEAL, EH791-030-T, SIC X SIC
MECHANICAL SEAL SLEEVE, 25 H43
ADJUST LINER, 30 X 20 T0.3
ADJUST LINER, 30 X 20 T0.5
BOLT (IMPELLER), 5/16-24 UNF X 25
SCREW (VOLUTE CASING), M8 X 20
SCREW (DRAIN COVER SET HANDLE),
M8 X 25
*
26
*
27
*
27-1
*
28
29
30
31
32
33
34
35
0131191270
0131191235
0105091055
0459220120
0723302040
CAP SCREW (CASING), M12 X 70
CAP SCREW (CASING), M12 X 35
BOLT (PUMP), M10 X 55
SEAL WASHER (CASING), M12, W12S1
CUSHION RUBBER, 40 X 20 M10,
NBR+SS400
1
4
2
1
4
36
37
0181090820
0181090825
BOLT SET WITH SPRING WASHER
(SUCTION COVER) M8 X 20
BOLT SET WITH SPRING WASHER
(SUCTION COVER) M8 X 25
2
4
QP-2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05) — PAGE 29
Download from Www.Somanuals.com. All Manuals Search And Download.
QP-2TZ — PUMP ASSY.
PUMP ASSY.
PAGE 30 — QP- 2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
QP-2TZ — PUMP ASSY.
PUMP ASSY.
NO.
38
PART NO.
0151191250
PART NAME
STUD BOLT (DRAIN COVER HANDLE),
M12 X 50 X15 X 20
QTY.
4
REMARKS
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
0520030413
43592012400011
0204490060
0205490080
0205490100
0205490100
0451290100
0401650080
0457290080
0451290080
0451290100
0451290080
0451290080
0451290080
0458220080
0742214050
1889068050
0741310700
1B20
KEY, 4.7 X 16
1
1
3
4
8
2
2
4
2
4
8
4
1
3
1
1
1
1
1
IMPELLER WASHER, 35 X 9 T4.5
U-NUT (WEAR PLATE, M6
NUT, ENGINE, M8
NUT, CUSHION RUBBER, M10
NUT, PUMP, M10
SPRING WASHER, PUMP, M10
WASHER, ENGINE, M8
SPRING WASHER (VOLUTE CASING), M8
SPRING WASHER (DRAIN COVER SET), M8
SPRING WASHER (CUSHION RUBBER), M10
SPRING WASHER (ENGINE), M8
SPRING WASHER (IMPELLER), M8
SPRING WASHER (CASING COVER ), M8
SEAL WASHER (CASING COVER)
STRAINER
CAP
O’RING, G70
ENGINE, HATZ
KIT2T
KIT, MECHANICAL SEAL, SLEEVE, & O-RINGS .. 1 ........... INCLUDES ITEMS W/
*
QP-2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05) — PAGE 31
Download from Www.Somanuals.com. All Manuals Search And Download.
HATZ 1B20 — SPARE PARTS KIT ASSY.
SPARE PARTS KITS ASSY.
PAGE 32 — QP- 2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HATZ 1B20 — SPARE PARTS KIT ASSY.
SPARE PARTS KITS ASSY.
NO.
1
2
3
4
PART NO.
01554100
01554200
01554300
01554400
PART NAME
QTY.
REMARKS
GASKET SET CYL. HEAD
GASKET SET CRANKCASE
MAINTENANCE KIT- 1000 HRS
EMERGENCY KIT
1
1
1
1
QP-2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05) — PAGE 33
Download from Www.Somanuals.com. All Manuals Search And Download.
HATZ 1B20 — ACCESSORIES ASSY.
ACCESSORIES ASSY.
PAGE 34 — QP- 2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HATZ 1B20 — ACCESSORIES ASSY.
ACCESSORIES ASSY.
NO.
1
2
3
4
PART NO.
01331001
05110401
05130000
05130100
PART NAME
TOOL KIT
DECAL MAINTENANCE
DECAL START
DECAL
QTY.
REMARKS
1
1
1
1
QP-2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05) — PAGE 35
Download from Www.Somanuals.com. All Manuals Search And Download.
HATZ 1B20 — CRANKCASE AND ENGINE MOUNT ASSY.
CRANKCASE AND ENGINE MOUNT ASSY.
NOTE: Refer to Table 9 at the end of the manual for letter ( A to L) call-outs.
PAGE 36 — QP- 2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HATZ 1B20 — CRANKCASE AND ENGINE MOUNT ASSY.
CRANKCASE AND ENGINE MOUNT ASSY.
NO.
1
PART NO.
01552210
PART NAME
CRANKCASE ASSEMBLY
QTY.
1
REMARKS
2
3
CRANKCASE ........................................... 1 ........... NOT SOLD SEPARATELY
*
03455000
40002600
04105400
05084300
50440300
50249101
04005500
50062300
04112800
04098000
50423200
04115200
01316000
04125000
PLUG 6.5X7
BLIND RIVET
COVER PLATE
PIN
1
2
1
1
*
5
6
*
*
7
8
*
O- RING.................................................... 1 ........... INCLUDED IN CRANKC. GASK. SET
*
9
CYL. PIN
PLUG
SCREW M10X1
PLUG
1
1
1
1
*
10
*
11
*
12
*
13
SEALING STRIP 331.5 MM ..................... 1 ........... INCLUDED IN CRANKC.GASK. SET
OIL SEAL 40X55X10................................ 1 ........... INCLUDED IN CRANKC. GASK. SET
14
15
16
GRUB SCREW
DIPSTICK W/SEALING RING .................. 1 ........... INCLUDES ITEMS W/%
SEALING RING
DIPSTICK................................................. 1 ........... NOT SOLD SEPARATELY
1
17%
18%
19
20
21
22
23
24
25
1
50208500
04121900
04099302
04105710
01542702
50373100
50469800
SPRINGWASHER
ALL. SCREW M8X35
ENGINE BRACKET
TUBE F. OIL FILTER
8
8
4
1
OIL SUCTION FILTER ............................. 1 ........... INCLUDES ITEMS W/ #
DRAIN PLUG M22X1.5 ............................ 1 ........... INCLUDED IN MAINTENANCE KIT
JOINT A22X27 ......................................... 1 ........... INCLUDED IN CRANKC. GASK. SET
AND MAINTENANCE KIT
26
27
28
29
30
31
32
33
05036900
04104400
04104500
50423300
04094400
50328000
01555800
03568700
HOSE CLIP
SUCTION PORT
SIEVE
BALL BEARING 6308
PLATE
CENTER SUNK SCREW AM6X16
COVER
2
1
1
1
2
4
1
1
RUBBER DIAPHRAGM
35#
36#
37#
38#
39
40
41
FILTER, OIL SUCTION ............................ 1 ........... NOT SOLD SEPARATELY
50475900
05148200
50170700
99400696
50208500
50022900
O- RING 20X4
PLATE SPRING
ALL. SCREW M6X16
ISOLATOR
1
2
1
4
8
8
SPRINGWASHER
NUT M8
QP-2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05) — PAGE 37
Download from Www.Somanuals.com. All Manuals Search And Download.
HATZ 1B20 — CRANKSHAFT ASSY.
CRANKSHAFT ASSY.
PAGE 38 — QP- 2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HATZ 1B20 — CRANKSHAFT ASSY.
CRANKSHAFT ASSY.
NO.
1
PART NO.
01552700
PART NAME
QTY.
REMARKS
CRANKSHAFT NO. X W/ PLUG.......................... 1 .................INCLUDES ITEMS W/
*
2
*
3
*
9
10
11
12
13
15
16
CRANKSHAFT .................................................... 1 .................NOT SOLD SEPARATELY
04125300
05100000
40032500
50120600
04114201
50443600
05107301
50463400
CLOSING PLUG 12 MM
STUB SHAFT 20 DIA.
1
1
1
1
1
1
1
1
SUPPORTING DISK 40X50X2.5
CIRCLIP A40X1.75
DISK 18.5X37X5
HEX. SCREW M18X1.5X55
STUB SHAFT SEM FINISHED 27 MM DIA.
FITTING KEY A5X5X36
QP-2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05) — PAGE 39
Download from Www.Somanuals.com. All Manuals Search And Download.
HATZ 1B20 — CAMSHAFT ASSY.
CAMSHAFT ASSY.
PAGE 40 — QP- 2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HATZ 1B20 — CAMSHAFT ASSY.
CAMSHAFT ASSY.
NO.
PART NO.
01503520
01326400
50123200
01326600
50255300
01326500
PART NAME
QTY.
REMARKS
1
CAMSHAFT ASSY. ..................................... 1 ..............INCLUDES ITEMS W/
*
3
*
4
*
5
*
6
*
7
*
8
*
9
10
11
12
13
14
CAMLEVER
SHIM 5X10X0.5 DIN988
FLYWEIGHT
LOCKWASHER
FLYWEIGHT
1
2
1
2
1
CAMSHAFT................................................. 1 ..............NOT SOLD SEPARATELY
04121700
04112100
04112200
04112300
04125100
04125200
WASHER 0.9MM 23X38X0.9
WASHER 1.0MM 23X38X1.0
WASHER 1.1MM 23X38X1.1
WASHER 1.2MM 23X38X1.2
WASHER 1.3MM 23X38X1.3
WASHER 1.4MM 23X38X1.4
1
1
1
1
1
1
QP-2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05) — PAGE 41
Download from Www.Somanuals.com. All Manuals Search And Download.
HATZ 1B20 — PISTON ASSY.
PISTON ASSY.
PAGE 42 — QP- 2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HATZ 1B20 — PISTON ASSY.
PISTON ASSY.
NO.
1
PART NO.
01317100
PART NAME
QTY.
REMARKS
PISTON 69MM ASSY. ................................. 1 ..............INCLUDES ITEMS W/
*
2 %
PISTON 69MM ............................................ 1 ..............NOT SOLD SEPARATELY
*
3 % 50425500
CIRCLIP
PISTON PIN
PISTON RING SET 69MM
2
1
1
*
4 % 50425400
*
5 % 01317200
*
6%
7
CYLINDER .................................................. 1 ..............NOT SOLD SEPARATELY
CYLINDER WITH PISTON ASSY. ............... 1 ..............INCLUDES ITEMS W/%
CONROD ASSY. ......................................... 1 ..............INCLUDES ITEMS W/$
CONROD ..................................................... 1 ..............NOT SOLD SEPARATELY
01554500
01500100
8
9$
10$
11
12
05046900
01575700
01581900
CONROD SCREW
BIG END BEARING
BIG END BEARING - 0.5MM
2
1
1
QP-2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05) — PAGE 43
Download from Www.Somanuals.com. All Manuals Search And Download.
HATZ 1B20 — CYLINDER HEAD ASSY.
CYLINDER HEAD ASSY.
PAGE 44 — QP- 2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HATZ 1B20 — CYLINDER HEAD ASSY.
CYLINDER HEAD ASSY.
NO.
1
PART NO.
01500221
PART NAME
QTY.
REMARKS
CYLINDER HEAD ASSY ................................. 1 ............... INCLUDES ITEMS W/
*
2
*
3
*
6
CYLINDER HEAD ............................................ 1 ............... NOT SOLD SEPARATELY
05119400
05062500
05054000
04107500
05053200
05053300
50425800
04093700
04093600
04093800
50425700
50445100
05091101
50358000
05054700
05050900
05061201
50364300
05055700
VALVE GUIDE
STUD CYLINDER HEAD 128MM
PUSH ROD
2
4
2
7
8
9
SEALING RING CYL. HEAD ........................... 2 ............... INCLUDED IN CRANKC. GASK. SET
VALVE, INTAKE
VALVE, EXHAUST
1
1
10
11
12
13
14
15
16
17
18
19
20
21
22
23
VALVE STEM SEAL CAP ............................... 2 ............... INCLUDED IN CRANKC. GASK. SET
WASHER
2
2
2
2
4
2
VALVE SPRING
SPRING PLATE
COLLET
DISK 6X12X1.2 DIN 988
SLIDER
GRUB SCREW M8X10 .................................... 2 ............... INCLUDED IN MAINTENANCE KIT
NUT FOR ROCKER ARM
ROCKER
WASHER 8.1X20X3
HEX. NUT M8 DIN 934
2
2
4
4
HEAD COVER GASKET ................................. 1 ............... INCLUDED IN CRANKC. GASK. SET
AND MAINTENANCE KIT
24
25
05047310
01509600
CYLINDER HEAD COVER
DOSING DEVICE ASSY ................................. 1 ............... INCLUDES ITEMS W/+
........................................................................................... INCLUDED IN EMERGENCY KIT
1
26+
27+
28
29
30
32
33
34
35
36
37
38
39
40
50425900
O- RING 16X2
2
DOSING DEVICE ............................................ 1 ............... NOT SOLD SEPARATELY
50081200
50374900
04117600
50129500
05059400
05059500
05059600
05059700
05059800
05059900
05060000
05060100
SPRING WASHER A6
ALL SCREW M6X35
LIFTING STRAP
HEX. NUT M8
CYLINDER HEAD GASKET 0.3MM
CYLINDER HEAD GASKET 0.4MM ................ 1 ............... INCLUDED IN HEAD GASKET SET
CYLINDER HEAD GASKET 0.5MM ................ 1 ............... INCLUDED IN HEAD GASKET SET
CYLINDER HEAD GASKET 0.6MM
CYLINDER HEAD GASKET 0.7MM
CYLINDER HEAD GASKET 0.8MM
CYLINDER HEAD GASKET 0.9MM
CYLINDER HEAD GASKET 1.0MM
2
2
1
2
1
1
1
1
1
1
QP-2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05) — PAGE 45
Download from Www.Somanuals.com. All Manuals Search And Download.
HATZ 1B20 — OIL PUMP/GOVERNOR ASSY.
OIL PUMP
NOTE: Refer to Table 9 at the end of the manual for letter ( A to L) call-outs.
PAGE 46 — QP- 2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HATZ 1B20 — OIL PUMP/GOVERNOR ASSY.
OIL PUMP/GOVERNOR
NO.
1
PART NO.
01530210
PART NAME
QTY.
REMARKS
COVER OIL PUMP ASSY. .............................. 1 ............... INCLUDES ITEMS W/
*
2
*
3
*
4
*
5
*
6
*
7
COVER, OIL PUMP ......................................... 1 ............... NOT SOLD SEPARATELY
CIRCLIP
50434901
1
GEAR, OIL PUMP ........................................... 1 ............... NOT SOLD SEPARATELY
HOUSING, OIL PUMP ..................................... 1 ............... NOT SOLD SEPARATELY
HOUSING, OIL PUMP ..................................... 1 ............... NOT SOLD SEPARATELY
05097100
50447900
50429400
05097300
04102900
50447400
50447500
05078600
50434800
05079400
01530402
50422400
50125800
50435000
05079800
05131600
05078900
05148600
50144400
50144500
04095600
03927300
05079301
50092700
50347100
01333000
50114300
50144500
50144400
50423900
04122900
01316402
RETAINING STRAP
BALL 3.5MM
1
1
4
1
1
1
1
1
2
1
1
2
2
2
5
3
1
1
1
1
1
1
1
4
1
1
2
1
3
1
1
1
8
9
ALL. SCREW M5X12
FLAT SPRING 0.4
OIL SUCTION TUBE
TUBE INSERT
TUBE INSERT
SHAFT
10
11
12
13
14
15
16
17
18
18
19
20
21
22
23
25
26
27
28
29
30
31
32
34
35
36
37
38
39
CIRCLIP
LEVER
GOVERNOR LEVER
SHIM 8X14X1
DISK 8X14X0.5
ALL. SCREW M3X12
INTERMED. PLATE
GOVERNOR SPRING 0.2MM
GOVERNOR SPRING 0.3
STOP SPRING 0.4MM
HEX. NUT M6
FLAT WASHER
LEVER
SCREW M6X32
SHAFT
CIRCLIP
BALL 3.175MM
CONSOLE
DISK
FLAT WASHER
HEX. NUT M6
CTR. SUNK SCREW M6X20
DISK
SUPPORT
QP-2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05) — PAGE 47
Download from Www.Somanuals.com. All Manuals Search And Download.
HATZ 1B20 — OIL PUMP/GOVERNOR ASSY. (CONT.)
OIL PUMP/GOVERNOR
NOTE: Refer to Table 9 at the end of the manual for letter ( A to L) call-outs.
PAGE 48 — QP- 2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HATZ 1B20 — OIL PUMP/GOVERNOR ASSY. (CONT.)
OIL PUMP/GOVERNOR
NO.
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
PART NO.
40022401
50138100
50004200
05079601
05078501
50475300
05151300
50475400
50328300
04122800
04000200
05130900
05130800
50465300
05146900
05147001
05151700
50475800
50475700
PART NAME
QTY.
1
2
1
8
1
1
1
1
1
1
1
1
1
2
4
1
REMARKS
O- RING 8X2
THREADED PIN M6X35
THREADED PIN M6X18
CENTRIFUGAL WEIGHT
GOVERNOR SLEEVE
FILL. HEAD SCREW 5X25
SUPPORT
PIN 5X8
HEX. NUT M6
PLATE SPRING
TENSION SPRING
GOVERNOR SPRING
STOP PLATE
CYL. SCREW M3X8
CENTRIFUGAL WEIGHT
GOVERNOR SLEEVE
PLUG
1
14
1
PLATE SPRING
GRUB SCREW M10X10
QP-2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05) — PAGE 49
Download from Www.Somanuals.com. All Manuals Search And Download.
HATZ 1B20 —TIMING COVER ASSY.
TIMING COVER ASSY.
NOTE: Refer to Table 9 at the end of the manual for letter ( A to L) call-outs.
PAGE 50 — QP- 2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HATZ 1B20 —TIMING COVER ASSY.
TIMING COVER ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
1
01319510
TIMING COVER ASSY.................................... 1 ............... INCLUDES ITEMS W/
*
2
*
3
*
4
*
5
*
5
TIMING COVER............................................... 1 ............... NOT SOLD SEPARATELY
CLOSING PLUG
BOLT GOVERNOR HOUSING
MAIN BEARING
MAIN BEARING - 0.5
OIL SEAL 30X47X8 ......................................... 1 ............... IN CRANKCASE GASKET SET
BALL
WASHER
CAM FOLLOWER
CAM FOLLOW SPINDLE
ALL. SCREW M6X25
04130200
01533900
05053100
04124800
40033700
50443400
03794100
05053400
03794201
50457900
1
1
1
1
6
*
7
*
8
1
3
2
2
2
9
10
11
12$
13$
14$
15$
16$
17$
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
BUSHING, ROCKER ARM .............................. 2 ............... NOT SOLD SEPARATELY
ROCKER ARM ................................................ 1 ............... NOT SOLD SEPARATELY
PIN, ROCKER ARM ........................................ 1 ............... NOT SOLD SEPARATELY
PIN, ROCKER ARM ........................................ 1 ............... NOT SOLD SEPARATELY
CLAMP, ROCKER ARM................................... 1 ............... NOT SOLD SEPARATELY
CLAMP, ROCKER ARM................................... 1 ............... NOT SOLD SEPARATELY
04094801
04095700
04094700
05095210
04133900
04095210
50448901
50144400
50384200
50426100
50162900
50469800
50373100
50459200
50095100
50248800
50453400
50392900
04097800
04106500
50358000
01319601
04096810
50469900
50274901
04122000
50038700
50148000
05127100
CUP
2
1
1
1
1
1
1
1
1
2
PRESSURE SPRING
DRAW ROD
SPRING
DISK 10.7X19X0.5
COVER
GRUB SCREW M6X30
HEX. NUT M6
ALL. SCREW M6X12
ALL. SCREW M8X120
JOINT A8X14 .................................................. 2 ............... IN CRANKCASE GASKET SET
JOINT A22X27 ................................................ 1 ............... IN MAINT. + CRANKCASE SET
DRAIN PLUG M22X1.5.................................... 1 ............... IN MAINTENANCE KIT
CLOSING SCREW M12X1.5
SPRING WASHER A8
ALL. SCREW M8X60
1
13
1
ALL. SCREW M8X45
ALL. SCREW M8X50
CENTERING RING SAE A
2
9
1
SEALING RING TIMING COVER .................... 2 ............... IN HEAD GASKET SET
38
39
GRUB SCREW M8X10
5
*
ROCKER ARM ................................................ 1 ............... INCLUDES ITEMS W/$
40
41
42
43
44
45
46
CAM FOLLOW SPINDLE
ALL. SCREW M6X30
GRUB SCREW M4X20
JOINT
1
1
1
1
1
1
1
STUD M8X50
HEX. NUT M8
LEVER
QP-2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05) — PAGE 51
Download from Www.Somanuals.com. All Manuals Search And Download.
HATZ 1B20 — FLYWHEEL ASSY.
FLYWHEEL ASSY.
PAGE 52 — QP- 2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HATZ 1B20 — FLYWHEEL ASSY.
FLYWHEEL ASSY.
NO.
PART NO.
01579710
01321310
50327300
50003400
04117300
PART NAME
QTY.
REMARKS
1
FLYWHEEL W/ BLOWER ................................ 1 ............... INCLUDES ITEMS W/
*
2
*
3
*
4
*
5
*
BLOWER RING
1
6
6
1
ALL. SCREW M4X20
SPRING WASHER A4
STICKER “TDC”
QP-2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05) — PAGE 53
Download from Www.Somanuals.com. All Manuals Search And Download.
HATZ 1B20 — FUEL INJECTION ASSY.
FUEL INJECTION ASSY.
PAGE 54 — QP- 2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HATZ 1B20 — FUEL INJECTION ASSY.
FUEL INJECTION ASSY.
NO.
1
PART NO.
01621600
01577110
PART NAME
QTY.
REMARKS
INJECTOR ASSY.................................. 1 ............. INCLUDES ITEMS W/$
NOZZLE HOLDER ASSY ..................... 1 ............. INCLUDES ITEMS W/#
PIPE ..................................................... 1 ............. NOT SOLD SEPARATELY
SEALING CONE 4.9MM ....................... 1 ............. SEE TECHNICAL ADVICE 95125801
2$
3#$
4#$
4
05096101
05070601
SEALING CONE 5.3MM
NIPPLE BODY ...................................... 1 ............. NOT SOLD SEPARATELY
1
5#$
6#$
8$
05081500
50436400
50436500
50436600
50436700
50436800
50436900
50437000
50437100
50437200
50437300
50437400
50437500
50437600
50437700
50437800
50437900
50438000
50438100
50438200
50438300
SEALING CONE
SHIM 1.00MM
SHIM 1.04MM
SHIM 1.10MM
SHIM 1.14MM
SHIM 1.20MM
SHIM 1.24MM
SHIM 1.30MM
SHIM 1.34MM
SHIM 1.40MM
SHIM 1.44MM
SHIM 1.50MM
SHIM 1.54MM
SHIM 1.60MM
SHIM 1.64MM
SHIM 1.70MM
SHIM 1.74MM
SHIM 1.80MM
SHIM 1.84MM
SHIM 1.90MM
SHIM 1.94MM
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
9$
10$
11$
12$
13$
14$
15$
16$
17$
18$
19$
20$
21$
22$
23$
24$
25$
26$
27$
28+$
29+$
30+$
SPRING ................................................ 1 ............. NOT SOLD SEPARATELY
SPRING WASHER ................................ 1 ............. NOT SOLD SEPARATELY
PLATE................................................... 1 ............. NOT SOLD SEPARATELY
NOZZLE................................................ 1 ............. IN EMERGENCY KIT
BODY.................................................... 1 ............. NOT SOLD SEPARATELY
JOINT ................................................... 1 ............. IN HEAD GASKET SET
31+$ 50442200
32+
33
05070500
QP-2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05) — PAGE 55
Download from Www.Somanuals.com. All Manuals Search And Download.
HATZ 1B20 — FUEL INJECTION ASSY. (CONT.)
FUEL INJECTION ASSY.
PAGE 56 — QP- 2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HATZ 1B20 — FUEL INJECTION ASSY. (CONT.)
FUEL INJECTION ASSY.
NO.
PART NO.
01322200
01330800
04096300
04096400
04096500
04096600
04096700
PART NAME
QTY.
REMARKS
34
INJECTION PUMP ............................... 1 ............. INCLUDES ITEMS W/
*
35
CONTROL SLEEVE
SHIM 0.2MM
SHIM 0.3MM
SHIM 0.4MM
SHIM 0.5MM
SHIM 0.6MM
1
1
1
1
1
1
*
36
*
37
*
38
*
39
*
40
*
41
*
VALVE, FUEL INJECTOR PUMP ......... 1 ............. NOT SOLD SEPARATELY
SPRING WASHER 8
BODY, FUEL INJECTOR PUMP ........... 1 ............. NOT SOLD SEPARATELY
42
*
50471600
50476900
1
43
*
44
*
WASHER
1
45
*
SPRING, FUEL..................................... 1 ............. NOT SOLD SEPARATELY
BODY, FUEL ......................................... 1 ............. NOT SOLD SEPARATELY
46
*
47
*
50476500
50445900
50476000
50433900
04097700
50323900
05089300
05056700
01326100
50464500
50110800
05129000
05130200
05084201
O- RING 17X2
VALVE HOLDER
DISC 8
O- RING 1.0X3.3
PIN
ALL. SCREW M6X30
RETAINING YOKE
FORK FOR INJECTOR
1
1
1
1
1
1
1
1
48
*
49
50
51
52
53
54
55
PARTS SET NOZZLE ASSY. ............... 1 ............. INCLUDES ITEMS W/+
56$
57$
58$
59$
60
HEX SCREW M6X16
JOINT A4X8
1
2
1
1
1
CONNECTING NIPPLE
HOSE 2.5X285
CONNECTING NIPPLE
QP-2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05) — PAGE 57
Download from Www.Somanuals.com. All Manuals Search And Download.
HATZ 1B20 — RECOIL STARTER ASSY.
RECOIL STARTER ASSY.
NOTE: Refer to Table 9 at the end of the manual for letter ( A to L) call-outs.
PAGE 58 — QP- 2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HATZ 1B20 — RECOIL STARTER ASSY.
RECOIL STARTER ASSY.
NO.
PART NO.
01515002
01497800
PART NAME
QTY.
REMARKS
1
RECOIL STARTER ASSY. ............................... 1 ............... INCLUDES ITEMS W/
*
2
HANDLE ASSY. ............................................... 1 ............... INCLUDES ITEMS W/#
HANDLE .......................................................... 1 ............... NOT SOLD SEPARATELY
*
3 #
*
4 #
5
03665200
05045201
01569300
50081200
50062700
05088901
01548800
05044901
05045001
50146300
50165600
05044800
05061300
50062700
50170900
50445800
05109100
RUBBER SLEEVE
RETURN SPRING
HOUSING RECOIL STARTER
SPRING WASHER A6
ALLEN SCREW M6X10
ROPE RECOIL STARTER
ROPE PULLEY
1
1
1
4
4
1
1
1
1
1
1
1
1
3
3
1
1
*
*
6
7
*
*
8
9
*
*
10
*
11
BRAKE SPRING
BRAKE DISK
*
12
*
13
*
HEX SCREW M6X18
SPRING WASHER
RATCHET
RETURN SPRING
ALLEN SCREW M6X10
SPRING WASHER 6
DRIVING SLEEVE
STICKER LABEL
14
*
15
*
16
*
17
18
19
20
QP-2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05) — PAGE 59
Download from Www.Somanuals.com. All Manuals Search And Download.
HATZ 1B20 — AIR DUCT ASSY.
AIR DUCT ASSY.
NOTE: Refer to Table 9 at the end of the manual for letter ( A to L) call-outs.
PAGE 60 — QP- 2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HATZ 1B20 — AIR DUCT ASSY.
AIR DUCT ASSY.
NO.
1
2
3
4
5
6
7
PART NO.
01533504
01316800
50170900
50146300
50461700
50144400
01316600
PART NAME
QTY.
REMARKS
HOOD
1
1
7
1
2
6
BLOWER DUCTING
SPRING WASHER 6
HEX SCREW M6X18
RUBBER SLEEVE
HEX NUT M6
COOLING AIR DUCTING ................................ 1 ............... INCLUDES ITEMS W/
*
8
9
AIR DUCT -----------------------------------------------1 ............... NOT SOLD SEPARATELY
*
04097600
50334800
50163801
50441600
50445400
50335600
50170700
50392610
50392800
01607000
04099500
04139000
01607100
01316500
SEALING STRIP 106.5 MM
RUBBER SLEEVE
RUBBER SLEEVE
WASHER 4,3
HEX. SCREW M4X10
COMBI SCREW M6X16
ALLEN SCREW M6X16
CAP
1
1
4
3
3
3
1
2
1
*
10
*
11
12
13
14
15
17
18
19
20
21
22
23
24#
25#
26
27
RUBBER SLEEVE
PARTING SHEET ............................................ 1 ............... ELECTRIC START ONLY
SEALING RING
SPACER TUBE 6.5X12X18
PARTING SHEET
1
5
1
COOLING AIR DUCT....................................... 1 ............... INCLUDES ITEMS W/#
AIR DUCT ........................................................ 1 ............... NOT SOLD SEPARATELY
04097600
04124500
04124600
SEALING STRIP 106.5MM
SEALING STRIP 470MM
SEALING STRIP 388MM
1
1
1
QP-2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05) — PAGE 61
Download from Www.Somanuals.com. All Manuals Search And Download.
HATZ 1B20 — AIR DUCT ASSY. (CONT.)
AIR DUCT ASSY.
NOTE: Refer to Table 9 at the end of the manual for letter ( A to L) call-outs.
PAGE 62 — QP- 2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HATZ 1B20 — AIR DUCT ASSY. (CONT.)
AIR DUCT ASSY.
NO.
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
PART NO.
50170800
03575500
00921400
04124400
50453300
01599500
04123200
50328000
50095100
50344700
50144500
50170900
50144400
04119100
50458100
05007300
04042000
04124300
04113800
01579300
50334800
05144100
PART NAME
QTY.
1
3
3
1
1
1
1
1
1
1
2
3
2
3
2
1
REMARKS
ALLEN SCREW M6X25
SEALING RING
SPACER BUSHING
SPACER 57MM
RUBBER SLEEVE
SUPPORT
THREAD, BUSH M6
CTR. SUNK SCREW AM6X16
SPRING WASHER A8
HEX. NUT M8
FLAT WASHER 6,4
SPRING WASHER 6
HEX. NUT M6
CLAMP
STUD M6X45
SEALING STRIP 48MM
WASHER 6.5X22.5X1
BUSH 6.5X13X16.5
COVER
3
2
1
1
2
1
COVER
RUBBER SLEEVE
SPRING CLIP
QP-2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05) — PAGE 63
Download from Www.Somanuals.com. All Manuals Search And Download.
HATZ 1B20 — CRANKCASE BREATHER ASSY.
CRANKCASE BREATHER ASSY.
PAGE 64 — QP- 2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HATZ 1B20 — CRANKCASE BREATHER ASSY.
CRANKCASE BREATHER ASSY.
NO.
1
PART NO.
01556400
PART NAME
QTY.
REMARKS
OIL SEPARATOR ASSY. ................................. 1 ............... INCLUDES ITEMS W/
*
2
*
3
*
4
*
5
OIL SEPARATOR ............................................. 1 ............... NOT SOLD SEPARATELY
FILTER BREATHER SYSTEM
BREATHER TUBE ........................................... 1 ............... IN CRANKCASE GASKET SET
SUCTION PIPE
05102900
01583700
01551600
1
1
QP-2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05) — PAGE 65
Download from Www.Somanuals.com. All Manuals Search And Download.
HATZ 1B20 — FUELTANK ASSY.
FUEL TANK ASSY.
NOTE: Refer to Table 9 at the end of the manual for letter ( A to L) call-outs.
PAGE 66 — QP- 2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HATZ 1B20 — FUELTANK ASSY.
FUEL TANK ASSY.
NO.
PART NO.
01578820
01535302
05084600
05085100
50440600
05084900
01534900
50441100
05084000
05086401
50440800
05123100
05085300
01534600
03673300
05122200
05130400
50440900
05085600
50231900
05109810
05086810
05122800
40028400
PART NAME
QTY.
REMARKS
1
FUEL TANK ASSY 3 LITER............................. 1 ............... INCLUDES ITEMS W/
*
2
CAP FOR FUEL TANK
SPRING
FUEL HOSE 7X165
NIPPLE FOR FUEL TANK
FUEL HOSE 7X190
FUEL VENT VALVE
1
1
1
1
1
1
*
3
*
4
*
5
*
6
*
7
*
8
HOSE CLIP ..................................................... 2 ............... IN EMERGENCY KIT
*
9
CONNECTING NIPPLE
GASKET FOR FUEL CAP
RUBBER SLEEVE
FUEL HOSE 7/70
FUEL HOSE 3.5X45
FUEL VENT VALVE
FUEL HOSE 4.5/170
FUEL PIPE
RUBBER SLEEVE
RUBBER SLEEVE
BREATHER HOSE
STUD M8X25
1
1
1
2
1
1
1
1
2
1
1
2
4
2
2
2
*
11
*
12
*
13
14
15
16
17
18
*
19
*
20
*
21
22
23
24
25
DISK 8.2X22X2
RUBBER SHELL
INSULATING SLEEVE
HEX. NUT M8
FUELTANK...................................................... 1 ............... NOT SOLD SEPARATELY
FUEL FILTER .................................................. 1 ............... IN MAINTENANCE KIT
INCLUDES ITEMS W/ #
26
*
27
*
01635200
28 # 50440900
RUBBER SLEEVE
CONNECTING NIPPLE
FUEL PIPE 7X70
TUBE 1.4X2X16
RUBBER SLEEVE
SPRING WASHER 6
HEX. NUT M6
1
1
1
1
2
2
2
1
2
2
4
2
2
2
2
2
1
1
1
1
1
2
1
*
29
30
31
32
34
35
36
37
38
39
40
41
42
43
44
49
50
51
52
53
54
55
05084400
05085000
05085500
05107700
50170900
50144400
05108511
01331300
50120000
05110010
01557000
04118800
50144500
50170900
50170700
05122700
05123200
03664300
50399801
50459600
50148100
05129610
*
*
SUPPORT
SUPPORT
DISK A6,4
DISK 7.1X17.9X2
HEX. SCREW M6X16
DISK 6.5X13X4.8
FLAT WASHER 6,4
SPRING WASHER 6
ALL. SCREW M6X16
HOSE NIPPLET
FUEL HOSE 3.5X38
FUEL HOSE 4.5X75
CLAMP 11,3
HOSE NIPPLE T
FLAT WASHER 8,4
CONNECTING NIPPLE
*
QP-2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05) — PAGE 67
Download from Www.Somanuals.com. All Manuals Search And Download.
HATZ 1B20 — AIR FILTER ASSY.
AIR FILTER ASSY.
NOTE: Refer to Table 9 at the end of the manual for letter ( A to L) call-outs.
PAGE 68 — QP- 2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HATZ 1B20 — AIR FILTER ASSY.
AIR FILTER ASSY.
NO.
PART NO.
$05082900
05056400
50171500
50426000
50454300
05054900
50435800
01515100
50452200
04104200
04103000
PART NAME
SEALING STRIP
WASHER
QTY.
REMARKS
1 $
1
1
3
*
2
3
ALL. SCREW M8X25
AIR FILTER ELEMENT ................................... 1 ............... IN MAINTENANCE KIT
NUT M6
COVER AIR FILTER
RUBBER SLEEVE
AIR FILTER HOUSING ASSY ......................... 1 ............... INCLUDES ITEMS W/
WING NUT M6
COVER, RUBBER INSERT
RUBBER INSERT
SEALING STRIP 365MM
SPRING WASHER A8
AIR FILTER ASSY .......................................... 1 ............... NOT SOLD SEPARATELY
GASKET AIR FILTER...................................... 2 ............... IN HEAD GASKET SET
INSULATING FLANGE
PLUG
VALVE PLATE
VALVE PLATE
SEALING STRIP 8X8X30
HOSE 2X4X215
AIR FILTER HOUSING .................................... 1 ............... INCLUDES ITEMS W/ $
4
5
6
7
8
9
10
11
1
1
1
*
1
1
1
1
2
12 $ 05056100
*
13
14 $
50095100
*
15
16
05056300
05088300
1
1
1
1
1
1
17 $ 05098100
*
18$
19$
20$
21$
22
05147100
05147200
03599000
05043810
01603600
QP-2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05) — PAGE 69
Download from Www.Somanuals.com. All Manuals Search And Download.
HATZ 1B20 — MUFFLER ASSY.
MUFFLER ASSY.
PAGE 70 — QP- 2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
HATZ 1B20 — MUFFLER ASSY.
MUFFLER ASSY.
NO.
1
2
3
4
5
6
7
8
PART NO.
40028300
50144500
01531311
05081101
05081410
50422500
01531201
05081611
50128100
05080100
50144500
40028300
50039500
50028800
50450500
01587800
05081002
05077810
05127000
50445000
40028400
50148100
50123000
01532300
05100300
05135000
PART NAME
QTY.
REMARKS
HEX. NUT M6
1
1
1
1
1
3
3
3
2
FLAT WASHER 6,4
EXHAUST END PIPE
THREADED BOLT M6
EXHAUST TUBE
CTR. SUNK SCREW M6X12
CLAMP
SUPPORTING PLATE
STUD
MUFFLER GASKET 1B20 ............................... 5 ............... IN HEAD GASKET SET
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
25
26
27
FLAT WASHER 6,4
HEX NUT M6
STUD M8X110
1
1
1
1
1
1
1
1
5
1
3
2
2
1
1
1
HEX. SCREW M8X90
HEX. SCREW M8X10
MUFFLER, INNER PART
COVER
MUFFLER, OUTER PART
WASHER, 28.1X34X0.5
CTR. SUNK. SCREW M6X35
HEX NUT M8
FLAT WASHER 8,4
DISK 8,4
MUFFLER GUARD
SEALING STRIP 65MM
SEALING STRIP 33MM
QP-2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05) — PAGE 71
Download from Www.Somanuals.com. All Manuals Search And Download.
HATZ 1B20 — SEALING AND BONDING ADHESIVES
TABLE 9. SEALING AND BONDING ADHESIVES
Item
A
Part Number
50223001
50223100
50223200
50223300
50223400
Description
Loctite Activator
Loctitie 573
Loctite 601
Amount
500 ml
50 ml
B
C
50 ml
D
Loctitie 221
Loctite 648
50 ml
E
10 ml
50223800
+ 50223900
Technicoll 8058
Technicoll 8367
0.75 kg
0.75 kg
F
G
H
J
50256501
50282501
50283003
50342600
50256600
Loctite IS 407
Silicon
10 g
30 ml
100 ml
100 g
100 g
High Temp Paste
High Temp Grease
Silicon Sealer
K
L
PAGE 72 — QP- 2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
Effective: October 1, 2002
TERMS AND CONDITIONS OF SALE — PARTS
PAYMENT TERMS
5. Partsmustbeinnewandresalablecon- Multiquipreservestherighttoquoteandsell
dition,intheoriginalMultiquippackage(if directtoGovernmentagencies,andtoOriginal
any), and with Multiquip part numbers Equipment Manufacturer accounts who use
Terms of payment for parts are net 10 days.
FREIGHTPOLICY
clearlymarked.
our products as integral parts of their own
products.
All parts orders will be shipped collect or
prepaidwiththechargesaddedtotheinvoice.
All shipments are F.O.B. point of origin.
Multiquip’sresponsibilityceaseswhenasigned
manifesthasbeenobtainedfromthecarrier,
andanyclaimforshortageordamagemustbe
settledbetweentheconsigneeandthecarrier.
6. Thefollowingitemsarenotreturnable:
SPECIALEXPEDITINGSERVICE
a. Obsolete parts. (If an item is in the
price book and shows as being re- A$35.00surchargewillbeaddedtotheinvoice
placedbyanotheritem,itisobsolete.) forspecialhandlingincludingbusshipments,
insuredparcelpostorincaseswhereMultiquip
mustpersonallydeliverthepartstothecarrier.
(such as gaskets, seals, “O” rings,
b. Any parts with a limited shelf life
andotherrubberparts)thatwerepur- LIMITATIONSOFSELLER’SLIABILITY
MINIMUMORDER
chasedmorethansixmonthspriorto
thereturndate.
Multiquip shall not be liable hereunder for
damagesinexcessofthepurchasepriceofthe
The minimum charge for orders from Mul-
tiquipis$15.00net.Customerswillbeasked
for instructions regarding handling of orders
notmeetingthisrequirement.
c. Anylineitemwithanextendeddealer item with respect to which damages are
netpriceoflessthan$5.00.
claimed, and in no event shall Multiquip be
liable for loss of profit or good will or for any
otherspecial,consequentialorincidentaldam-
ages.
d. Special order items.
RETURNEDGOODSPOLICY
e. Electricalcomponents.
f. Paint,chemicals,andlubricants.
g. Decalsandpaperproducts.
h. Itemspurchasedinkits.
Returnshipmentswillbeacceptedandcredit
willbeallowed,subjecttothefollowingprovi-
sions:
LIMITATIONOFWARRANTIES
Nowarranties,expressorimplied,aremade
in connection with the sale of parts or trade
accessoriesnorastoanyenginenotmanufac-
tured by Multiquip. Such warranties made in
connectionwiththesaleofnew,completeunits
are made exclusively by a statement of war-
rantypackagedwithsuchunits,andMultiquip
neitherassumesnorauthorizesanypersonto
assume for it any other obligation or liability
whatever in connection with the sale of its
products.Apartfromsuchwrittenstatementof
warranty, there are no warranties, express,
impliedorstatutory,whichextendbeyondthe
descriptionoftheproductsonthefacehereof.
1. AReturnedMaterialAuthorizationmust
be approved by Multiquip prior to ship-
ment.
7. Thesenderwillbenotifiedofanymaterial
receivedthatisnotacceptable.
2. ToobtainaReturnMaterialAuthorization,
alistmustbeprovidedtoMultiquipParts
Salesthatdefinesitemnumbers,quanti-
ties, and descriptions of the items to be
returned.
8. Suchmaterialwillbeheldforfiveworking
days from notification, pending instruc-
tions.Ifareplyisnotreceivedwithinfive
days,thematerialwillbereturnedtothe
senderathisexpense.
a. Thepartsnumbersanddescriptions
must match the current parts price
list.
9. Creditonreturnedpartswillbeissuedat
dealer net price at time of the original
purchase,lessa15%restockingcharge.
b. The list must be typed or computer
generated.
10. In cases where an item is accepted, for
which the original purchase document
can not be determined, the price will be
basedonthelistpricethatwaseffective
twelvemonthspriortotheRMAdate.
c. The list must state the reason(s) for
thereturn.
d. The list must reference the sales
order(s)orinvoice(s)underwhichthe
itemswereoriginallypurchased.
11. Credit issued will be applied to future
purchasesonly.
e. The list must include the name and
phonenumberofthepersonrequest-
ingtheRMA.
PRICINGANDREBATES
Prices are subject to change without prior
notice.Pricechangesareeffectiveonaspe-
cificdateandallordersreceivedonorafterthat
datewillbebilledattherevisedprice.Rebates
3. AcopyoftheReturnMaterialAuthoriza-
tionmustaccompanythereturnshipment.
4. Freight is at the sender’s expense. All forpricedeclinesandaddedchargesforprice
partsmustbereturnedfreightprepaidto increaseswillnotbemadeforstockonhand
Multiquip’sdesignatedreceivingpoint.
atthetimeofanypricechange.
QP-2TZ TRASH PUMP — OPERATION & PARTS MANUAL — REV. #0 (03/25/05) — PAGE 73
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND PARTS MANUAL
HERE'S HOW TO GET HELP
PLEASE HAVETHE MODEL AND SERIAL
NUMBER ON-HANDWHEN CALLING
MULTIQUIP CORPORATE OFFICE
18910 Wilmington Ave.
Carson, CA 90746
800-421-1244
FAX:310-537-3927
Email: mq@multiquip.com
Internet:www.multiquip.com
PARTS DEPARTMENT
800-427-1244
310-537-3700
FAX:800-672-7877
FAX:310-637-3284
MAYCO PARTS
800-306-2926
310-537-3700
FAX:800-672-7877
FAX:310-637-3284
SERVICE DEPARTMENT
800-421-1244
FAX:310-537-4259
310-537-3700
TECHNICAL ASSISTANCE
800-478-1244
FAX:310-631-5032
FAX:310-537-1173
WARRANTYDEPARTMENT
800-421-1244,EXT.279
310-537-3700,EXT.279
Your Local Dealer is:
MULTIQUIP INC.
18910 WILMINGTONAVE.
CARSON, CALIFORNIA 90746
800-421-1244 • 310-537-3700
FAX:310-537-3927
E-mail:mq@multiquip.com
Internet:multiquip.com
Download from Www.Somanuals.com. All Manuals Search And Download.
|
MTD Lawn Mower Series 400 User Manual
MTD Snow Blower 190 833 OEM User Manual
NewAir Air Conditioner ACP 1300H User Manual
Niles Audio Speaker CM700DS BKT User Manual
Nilfisk Advance America Vacuum Cleaner BR1100S User Manual
Nilfisk ALTO Stereo Amplifier A5002 User Manual
Northern Industrial Tools Impact Driver 1981202 User Manual
Ocean Kayak Marine Instruments 14561 User Manual
Omega Speaker Systems Thermometer OS550 BB Series User Manual
Oregon Scientific Weather Radio BAR609HGA User Manual