OPERATOR’S MANUAL
SNOW THROWER
MODEL
31AE640F352
IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY
Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush-
covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if
any). If a spark arrester is used, it should be maintained in effective working order by the operator. In the State of California the above is required
by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark
arrester for the muffler is available through your nearest engine authorized service dealer or contact the service department, P.O. Box 361131
Cleveland, Ohio 44136-9722.
MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-9722
770-10167D.
PRINTED IN U.S.A.
FORM NO
.
(6/2002)
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1: IMPORTANT SAFE OPERATION PRACTICES
This symbol points out important safety instructions, which if not followed, could endanger the personal
safety and/or property of yourself and others. Read and follow all instructions in this manual before
attempting to operate this machine. Failure to comply with these instructions may result in personal
injury. When you see this symbol—heed its warning.
WARNING: Engine Exhaust, some of its constituents, and certain vehicle components
contain or emit chemicals known to the State of California to cause cancer, birth defects or
other reproductive harm.
DANGER: This machine was built to be operated according to the rules for safe operation in this
manual. As with any type of power equipment, carelessness or error on the part of the operator can
result in serious injury. This machine is capable of amputating hands and feet and throwing objects.
Failure to observe the following safety instructions could result in serious injury or death.
7. Never attempt to make any adjustments while engine is
TRAINING
running, except where specifically recommended in the
operator’s manual.
8. Let engine and machine adjust to outdoor temperature
before starting to clear snow.
9. To avoid personal injury or property damage use extreme
1. Read, understand, and follow all instructions on the
machine and in the manual(s) before attempting to
assemble and operate. Keep this manual in a safe place
for future and regular reference and for ordering
replacement parts.
care in handling gasoline. Gasoline is extremely
2. Be familiar with all controls and their proper operation.
flammable and the vapors are explosive. Serious
Know how to stop the machine and disengage them
quickly.
personal injury can occur when gasoline is spilled on
yourself or your clothes, which can ignite. Wash your skin
3. Never allow children under 14 years old to operate this
and change clothes immediately.
machine. Children 14 years old and over should read and
a. Use only an approved gasoline container.
understand the operation instructions and safety rules in
b. Extinguish all cigarettes, cigars, pipes and other
this manual and should be trained and supervised by a
sources of ignition.
parent.
c. Never fuel machine indoors.
4. Never allow adults to operate this machine without
d. Never remove gas cap or add fuel while the
proper instruction.
engine is hot or running.
5. Thrown objects can cause serious personal injury. Plan
e. Allow engine to cool at least two minutes before
your snow-throwing pattern to avoid discharge of material
refueling.
toward roads, bystanders and the like.
6. Keep bystanders, helpers, pets and children at least 75
feet from the machine while it is in operation. Stop
machine if anyone enters the area.
7. Exercise caution to avoid slipping or falling, especially
f. Never over fill fuel tank. Fill tank to no more than
½ inch below bottom of filler neck to provide space
for fuel expansion.
g. Replace gasoline cap and tighten securely.
h. If gasoline is spilled, wipe it off the engine and
when operating in reverse.
equipment. Move machine to another area. Wait 5
minutes before starting the engine.
i. Never store the machine or fuel container inside
PREPARATION
where there is an open flame, spark or pilot light
1. Thoroughly inspect the area where the equipment is to
(e.g. furnace, water heater, space heater, clothes
be used. Remove all doormats, newspapers, sleds,
dryer etc.).
boards, wires and other foreign objects, which could be
j. Allow machine to cool at least 5 minutes before
tripped over or thrown by the auger/impeller.
storing.
2. Always wear safety glasses or eye shields during
operation and while performing an adjustment or repair to
OPERATION
protect your eyes. Thrown objects which ricochet can
cause serious injury to the eyes.
1. Do not put hands or feet near rotating parts, in the auger/
3. Do not operate without wearing adequate winter outer
impeller housing or discharge chute. Contact with the
garments. Do not wear jewelry, long scarves or other
rotating parts can amputate hands and feet.
loose clothing, which could become entangled in moving
2. The auger/impeller clutch lever is a safety device. Never
parts. Wear footwear which will improve footing on
bypass its operation. Doing so makes the machine
slippery surfaces.
4. Use a grounded three-wire extension cord and
unsafe and may cause personal injury.
3. The clutch levers must operate easily in both directions
receptacle for all units with electric start engines.
and automatically return to the disengaged position when
5. Adjust collector housing height to clear gravel or crushed
released.
rock surfaces.
6. Disengage all clutch levers before starting the engine.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Never operate with a missing or damaged discharge
chute. Keep all safety devices in place and working.
5. Never run an engine indoors or in a poorly ventilated
area. Engine exhaust contains carbon monoxide, an
odorless and deadly gas.
6. Do not operate machine while under the influence of
alcohol or drugs.
7. Muffler and engine become hot and can cause a burn. Do
not touch.
Contact your dealer or telephone 1-800-800-7310 for
assistance and the name of your nearest servicing
dealer.
MAINTENANCE AND STORAGE
1. Never tamper with safety devices. Check their proper
operation regularly. Refer to the maintenance and
adjustment sections of this manual.
2. Before cleaning, repairing or inspecting machine
disengage all clutch levers and stop engine. Wait until the
auger/impeller come to a complete stop. Disconnect the
spark plug wire and ground against the engine to prevent
unintended starting.
3. Check bolts and screws for proper tightness at frequent
intervals to keep the machine in safe working condition.
Also, visually inspect machine for any damage.
4. Do not change the engine governor setting or over-speed
the engine. The governor controls the maximum safe
operating speed of the engine.
5. Snow thrower shave plates and skid shoes are subject to
wear and damage. For your safety protection, frequently
check all components and replace with original
equipment manufacturer’s (OEM) parts only. “Use of
parts which do not meet the original equipment
specifications may lead to improper performance and
compromise safety!”
6. Check clutch controls periodically to verify they engage
and disengage properly and adjust, if necessary. Refer to
the adjustment section in this operator’s manual for
instructions.
7. Maintain or replace safety and instruction labels, as
necessary.
8. Observe proper disposal laws and regulations for gas,
oil, etc. to protect the environment.
9. Prior to storing, run machine a few minutes to clear snow
from machine and prevent freeze up of auger/impeller.
10. Never store the machine or fuel container inside where
there is an open flame, spark or pilot light such as a water
heater, furnace, clothes dryer etc.
8. Exercise extreme caution when operating on or crossing
gravel surfaces. Stay alert for hidden hazards or traffic.
9. Exercise caution when changing direction and while
operating on slopes.
10. Plan your snow-throwing pattern to avoid discharge
towards windows, walls, cars etc. Thus, avoiding
possible property damage or personal injury caused by a
ricochet.
11. Never direct discharge at children, bystanders and pets
or allow anyone in front of the machine.
12. Do not overload machine capacity by attempting to clear
snow at too fast of a rate.
13. Never operate this machine without good visibility or
light. Always be sure of your footing and keep a firm hold
on the handles. Walk, never run.
14. Disengage power to the auger/impeller when
transporting or not in use.
15. Never operate machine at high transport speeds on
slippery surfaces. Look down and behind and use care
when in reverse.
16. If the machine should start to vibrate abnormally, stop the
engine, disconnect the spark plug wire and ground it
against the engine. Inspect thoroughly for damage.
Repair any damage before starting and operating.
17. Disengage all clutch levers and stop engine before you
leave the operating position (behind the handles). Wait
until the auger/impeller comes to a complete stop before
unclogging the discharge chute, making any
adjustments, or inspections.
18. Never put your hand in the discharge or collector
openings. Always use the clean-out tool provided to
unclog the discharge opening. Do not unclog discharge
chute while engine is running. Shut off engine and remain
behind handles until all moving parts have stopped
before unclogging.
11. Always refer to the operator’s manual for proper
instructions on off-season storage.
WARNING — YOUR RESPONSIBILITY:
Restrict the use of this power machine to persons who
read, understand and follow the warnings and
instructions in this manual and on the machine. The
safety labels are shown below for your reference.
19. Use only attachments and accessories approved by the
manufacturer (e.g. wheel weights, tire chains, cabs etc.).
20. If situations occur which are not covered in this manual,
use care and good judgment.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 2: ASSEMBLING YOUR SNOW THROWER
Loose Parts
Auger Shear Bolts (Spares)
Cupped
Washer
Upper
Handle
Carriage
Bolt
Hex Lock Nuts
5/16” Thread
(712-0429)
Wing
Nuts
Shear Bolts
(710-0890A)
NOTE: The augers are secured to the spiral shaft with
two shear bolts and hex lock nuts. If you hit a hard
foreign object or ice jam, the snow thrower is designed
so that the bolts may shear. Two replacement shear
bolts and nuts are provided for your convenience. Store
in a safe place until needed.
Lower
Handle
IMPORTANT: NEVER replace the auger shear bolts with
standard hex bolts. Any damage to the auger gearbox
or other components as a result of doing so will NOT be
covered by your snow thrower’s warranty.
Figure 1
Upper
WARNING: Disconnect spark plug wire
and ground it against the engine to prevent
unintended starting.
Shift Rod
Shift Rod
Connector
Hex Nut
Lower
Shift Rod
Assembly
NOTE: All references to right or left side of the snow
thrower are determined from behind the unit in the
operating position. The “operator’s position” is defined
as standing directly behind the snow thrower, facing the
handle panel.
Eyebolt
WARNING: Disconnect the spark plug
wire and ground it against the engine to
prevent unintended starting.
Figure 2
•
•
Retighten the wing nut to secure the chute
directional control in this position. See Figure 2.
Slide the shift rod connector down over the end of
the lower shift rod. Tap the top of connector until it
locks on the lower shift rod.
•
Remove the lower two plastic wing nuts, cupped
washers and carriage bolt (eyebolt on the left side)
from the lower handle. See Figure 1.
Raise the upper handle assembly until it aligns with
lower handle.
Be sure both cables are aligned with cable roller
guides located in the lower rear of snow thrower
frame.
•
•
NOTE: If the connector is not properly assembled, the
shift rod will pivot and you will not be able to shift gears
or change directions.
•
•
Secure the upper handle and lower handle with the
plastic wing nuts, cupped washers, and carriage
bolt (eyebolt on the left side) previously removed.
Adjust the eyebolt on the chute directional control
so the control rod does not come into contact with
the engine by moving the hex nut against the
handle (if necessary).
Lamp Wiring
•
Wrap the wire from the lamp down the right handle
until the wire can be plugged into the alternator lead
wire located under the fuel tank. See Figure 3.
IMPORTANT:Lamp wire must not interfere with any
controls or cables.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Gas and Oil
After assembly, service engine with gasoline, and
check oil level as instructed in the engine manual.
Lower Handle
Lamp Wire
Alternator Lead
NOTE: Refer to Auger Control Test on page 8 prior to
operating your snow thrower. Read and follow all
instructions carefully and perform all adjustments to
verify your snow thrower is operating safely and
properly.
Figure 3
SECTION 3: KNOW YOUR SNOW THROWER
Chute Directional Control
Operating Controls
The chute directional control is located on left hand side
of the snow thrower.To change the direction in which
snow is thrown, rotate chute directional control as
follows:
WARNING: Be familiar with all controls and
their proper operation. Know how to stop the
machine and disengage them quickly.
•
•
Clockwise to discharge to the left.
Counterclockwise to discharge to the right.
Shift Lever
The shift lever is located in the center of the handle
panel. The shift lever may be moved into one of eight
positions. Run engine with throttle in the fast position.
Use the shift lever to determine ground speed.
Chute Clean-out Tool
WARNING: Never use your hand to clear a
clogged discharge chute. Shut off engine and
remain behind handles until all moving parts
have stopped before unclogging.
Forward: There are six speeds. Position one (1) is the
slowest. Position six (6) is the fastest.
Reverse: There are two reverse (R) speeds R1 and R2.
The “R2” closest to the operator (all the way back) is the
faster of the two.
The chute clean-out tool (see Figure 4) isdesigned to
clear a clogged discharge chute. Refer to Operating Your
Snow Thrower on page 9 for detailed instructions on how
toproperly use the chute clean-out tool.
Auger Control
The auger control is located on the left handle. Squeeze
the control to engage the augers; release to stop the
augers. The traction control must also be released.
Ignition Key
The ignition key must be inserted in the switch in order
for the engine to start. Remove the ignition key when
the snow thrower is not in use.
Traction / Auger Control Lock
The traction control is located on the right handle.
Squeeze the control to engage the wheel drive.
Release to stop.
NOTE: Do NOT “turn” the ignition key in an attempt to
start the engine.
Throttle Control
The throttle control is located on the engine. It regulates
the speed of the engine. See Figure 4.
This same control also locks the auger control so you
can turn the chute directional control without
interrupting the snow throwing process. If the auger
control is engaged with the traction control engaged,
the operator can release the auger control (on the left
handle) and the augers will remain engaged. Release
the traction control to stop both the augers and wheel
drive (auger control must also be released).
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Shift Lever
Auger Control
Traction/Auger
Control Lock
Discharge Chute
Spark Plug
Primer
Choke
Chute
Clean-out Tool
Recoil Starter
Handle
Chute Directional Control
Ignition Key
Throttle Control
Auger
Figure 4
SECTION 4: OPERATING YOUR SNOW THROWER
•
Attach spark plug wire to spark plug. Make certain
the metal loop on end of the spark plug wire (inside
the boot) is fastened securely over the metal tip on
the spark plug. See Figure 5.
Before Starting
WARNING: Read, understand, and follow
all instructions and warnings on the machine
and in this manual before operating.
Metal Loop
•
The spark plug wire was disconnected for safety.
Attach spark plug wire to spark plug before starting.
Rubber Boot
Figure 5
Gas And Oil Fill-up
•
•
•
Make certain the fuel shut-off valve, if so equipped,
is in the OPEN (vertical) position.
Make certain the auger and traction controls are in
the disengaged (released) position.
Move throttle control up to FAST position. Insert
ignition key into slot. Be certain it snaps into place.
Do not turn key. See Figure 4.
•
At the factory, a plastic cup is inserted inside the
fuel tank’s fill opening (beneath the fuel cap) to
prevent debris from entering the fuel tank during
assembly. Remove and discard this cup before
filling up the tank.
WARNING: Use extreme care when
handling gasoline. Gasoline is extremely
flammable and the vapors are explosive.
Never fuel machine indoor or while the
engine is hot or running. Extinguish
cigarettes, cigars, pipes and other sources of
ignition.
NOTE: Engine will not start unless ignition key is
inserted into ignition slot in carburetor cover. Do not
turn ignition key.
Recoil Starter:
•
•
•
•
Rotate choke knob to FULL choke position (cold
engine start).
If engine is warm, place choke in OFF position
instead of FULL.
Push primer button three or four times for cold
engine start.
If engine is warm, push primer button once only.
Starting Engine
IMPORTANT: Prior to operating your snow
thrower, read, understand and follow ALL
instructions to perform adjustments found
under the heading Auger Control Test on
page 8 of this manual.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: Always cover vent hole in primer button when
pushing. Additional priming may be necessary for first
start if temperature is below 15 degrees Fahrenheit.
To prevent starter freeze-up:
•
Run engine for a few minutes before stopping to
help dry off any moisture on the engine.
•
Electric Starter: Connect power cord to switch box
on engine, then to 120 volt AC receptacle. With the
engine running, push starter button and spin the
starter for several seconds. The unusual sound
made by spinning the starter will not harm engine or
starter. Disconnect the power cord from receptacle
first, and then from switch box.
Recoil Starter: With engine running, pull starter
rope with a rapid, continuous full arm stroke three
or four times. Pulling the starter rope will produce a
loud clattering sound, which is not harmful to the
engine or starter.
Wipe all snow and moisture from the carburetor
cover in the area of the control levers. Also, move
control levers back and forth several times. Leave
throttle control lever in the STOP or OFF position.
Leave choke control in the FULL choke position.
Remove ignition key and disconnect spark plug
wire. Do not turn key.
•
•
Grasp starter handle and pull rope out slowly, until it
pulls slightly harder. Let rope rewind slowly.
Pull starter handle rapidly. Do not allow handle to
snap back. Allow it to rewind slowly while keeping a
firm hold on the starter handle.
•
•
Repeat step above until engine starts.
As engine warms up and begins to operate evenly,
rotate choke knob slowly to OFF position. If engine
falters, return to FULL choke, then slowly move to
OFF position.
•
•
•
Electric Starter
The electric starter is equipped with a grounded three-
wire power cord and plug, and is designed to operate
on 120 volt AC household current.
WARNING: The electric starter must be
used with a properly grounded three-prong
receptacle at all times to avoid possibility of
electric shock. Follow all instructions carefully
to operate the electric starter.
IMPORTANT: Do not lose the ignition key. Keep it in a
safe place. Engine will not start without the ignition key.
•
•
•
Determine that your house wiring is a three-wire
grounded system. Ask a licensed electrician if you
are not certain.
If your home wiring system is not a three-wire
grounded system, do not use this electric starter
under any conditions.
If your home electrical system is grounded, but
a three-hole receptacle is not available, one should
be installed by a licensed electrician before using
the electric starter.
If you have a grounded three-prong receptacle,
proceed as follows.
Rotate choke knob to OFF position.
Connect power cord to switch box on engine. Plug
the other end of power cord into a three-prong 120-
volt, grounded, AC receptacle.
Push starter button to crank engine. As you crank
the engine, move choke knob to FULL choke
position.
When engine starts, release starter button, and
move choke gradually to OFF. If engine falters,
move choke immediately to FULL and then
gradually to OFF.
When disconnecting the power cord, always unplug
from the three-prong receptacle first, and then from
the snow thrower.
To Engage Drive
•
With the engine running near top speed, move shift
lever into one of the five FORWARD positions or
two REVERSE positions. Select a speed
appropriate for the snow conditions that exist. Use
the slower speeds until you are familiar with the
operation of the snow thrower.
•
•
Squeeze the auger control and the augers will turn.
Release it and the augers will stop.
Squeeze traction control and the snow thrower will
move. Release it and unit will stop. Never move
shift lever without releasing traction control.
•
•
•
To Engage Augers
•
•
•
To engage augers and start throwing snow,
squeeze the auger control against the left handle.
Release to stop the augers.
Auger Control Test
IMPORTANT: Perform the following test before operating
the snow thrower for the first time and at the start of
each winter season.
•
Check the adjustment of the auger control as follows:
•
When the auger control is released and in the
disengaged “up” position, the cable should have
very little slack, but should NOT be tight.
To Stop Engine
•
To stop engine, remove the ignition key. Do not turn
key. Disconnect the spark plug wire from the spark
plug to prevent accidental starting while equipment
is unattended.
WARNING: Do not over-tighten the cable.
Over-tightening may prevent the auger from
disengaging and compromise the safety of the
snow thrower.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Stop the engine by removing the ignition key.
3. Remove the clean-out tool from the clip which
secures it to the rear of the auger housing.
4. Use the shovel-shaped end of the clean-out tool to
remove any snow and ice in the discharge chute.
WARNING: Never use your hand to clear a
clogged discharge chute. Shut off engine and
remain behind handles until all moving parts
have stopped before unclogging.
"Z" Fitting
5. Refasten the clean-out tool to the mounting clip on
the rear of the auger housing, re-start the engine.
6. While standing in the operator’s position (behind
the snow thrower), engage the auger clutch lever
for a few seconds to clear any remaining snow or
ice from the discharge chute before continuing to
clear snow.
Jam Nut
Make sure cable is straight
Figure 6
•
In a well-ventilated area, start the snow thrower
engine as instructed earlier in this section under the
heading Starting Engine. Make sure the throttle is set
in the FAST position.
While standing in the operator’s position (behind
the snow thrower) engage the auger.
Tire Chains (Optional Equipment)
Tire chains may be used whenever extra traction is
needed. Contact Customer Support as instructed on
page 2 for information regarding price and availability.
•
•
Snow Thrower Model
Tire Chain Kit
Allow the auger to remain engaged for
31AE640F352
OEM-390-991
approximately ten (10) seconds before releasing
the auger control. Repeat this several times.
With the engine running in the FAST position and
the auger control lever in the disengaged “up”
position, walk to the front of the machine.
Confirm that the auger has completely stopped
rotating and shows NO signs of motion.
Drift Cutters (Optional Equipment)
•
•
Drift cutters should be used when operating the snow
thrower in heavy drift conditions. Contact Customer
Support as instructed on page 2 for information
regarding price and availability.
Snow Thrower Model
Drift Cutter Kit
IMPORTANT: If the auger shows ANY signs of rotating,
immediately return to the operator’s position and shut
off the engine. Wait for all moving parts to stop before
readjusting the auger control cable.
31AE640F352
OEM-390-679
Operating Tips
NOTE: Allow the engine to warm up for a few minutes
as the engine will not develop full power until it reaches
operating temperature.
•
To readjust the control cable, loosen the hex jam
nut on the auger control cable “Z” fitting.
Rotate the coupling end of the cable
•
counterclockwise to provide more slack.
Retighten the hex jam nut. See Figure 6.
Repeat Auger Control Test to verify proper
adjustment has been achieved.
•
•
WARNING: The muffler, engine and their
surrounding areas become hot and can cause
a burn. Do not touch.
•
•
Discharge snow downwind whenever possible.
Slightly overlap each previous path.
Set the skid shoes 1/4" below the scraper bar for
normal usage. The skid shoes may be adjusted
upward for hard-packed snow. Adjust downward
when using on gravel or crushed rock.
Chute Clean-out Tool
The chute clean-out tool is conveniently fastened to the
rear of the auger housing with a mounting clip (Refer to
Figure 4). If the discharge chute becomes clogged
during operation, proceed as follows to safely clean the
chute and chute opening:
•
Avoid possible starter freeze-up. Clean the snow
thrower thoroughly after each use.
1. Release both the Auger Control Lever and the
Traction/Auger Control Lock Lever.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 5: MAKING ADJUSTMENTS
WARNING: NEVER attempt to make any
adjustments while the engine is running,
except where specified in the operator’s
manual.
WARNING: Drain the gasoline out of snow
thrower engine, place a piece of plastic film
under the gas cap to avoid spillage before
beginning the job.
To test further for correct adjustment, if necessary,
proceed as follows:
Auger Control
Refer to Auger Control Test on page 8 to adjust the auger
•
•
•
Tip the snow thrower forward, allowing it to rest on
the auger housing.
control.
Remove the frame cover underneath the snow
thrower by removing six self-tapping screws.
With the traction control released, there must be
clearance between the friction wheel and the drive
plate in all positions of the shift lever.
Chute Assembly
The distance snow is thrown can be adjusted by
changing the angle of the chute assembly. To do so,
stop the engine by removing the ignition key and loosen
the plastic wing knobs found on either side of the
discharge chute. Pivot the chute upward or downward
before re-tightening the wing knobs.
•
With traction control engaged, the friction wheel
must contact the drive plate. See Figure 7.
Friction
Wheel
Tire Pressure
•
The tires are over-inflated for shipping purposes.
Before operating, check tire pressure and reduce, if
necessary, to between 15 psi and 20 psi.
Gear Shaft
NOTE: If the tire pressure is not equal in both tires, the
unit may pull to one side or the other.
Traction Control and Shift Lever
Drive
Plate
•
To check the adjustment of the traction control and
shift lever, proceed as follows:
•
With the engine off, move the shift lever all the way
forward to sixth (6) position. With the traction
control released, push the snow thrower forward.
The unit should move forward freely. Then engage
the traction control grip. Wheels should stop
turning.
Figure 7
If adjustment is necessary:
•
•
•
Loosen the jam nut on the traction drive cable and
thread the cable in or out as necessary.
Retighten the jam nut to secure the cable when
correct adjustment is reached.
•
•
Now release the traction control grip, and push the
unit again.
Move the shift lever back to the fast reverse
position, then all the way forward again. There
should be no resistance in the shift lever, and
wheels should keep turning.
Reassemble the frame cover.
NOTE: If you placed plastic film under the gas cap, be
certain to remove it before operating the snow thrower.
•
•
If you feel resistance when moving the shift lever or
the wheels stop when they should not, loosen the
jam nut on the traction control cable and unthread
the cable one turn.
If the wheels do not stop when you engage the
traction control grip, loosen the jam nut on the
traction control cable and thread the cable in one
turn. Recheck the adjustment and repeat as
necessary. Tighten the jam nut to secure the cable
when correct adjustment is reached.
Shift Rod
To adjust the shift rod, proceed as follows.
•
Remove the hairpin clip and flat washer from the
shift handle under the handle panel.
•
Place shift lever in sixth (6) position or the fastest
forward speed.
•
•
Push shift arm assembly down as far as it will go
Rotate the ferrule up or down on the shift rod as
necessary until the ferrule lines up with the upper
hole in the shift lever. See Figure 8.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Shift
Lever
Ferrule
Upper
Shift Rod
Carriage Bolts
Hex Nuts
Shift Rod
Connector
Skid Shoe
Hairpin
Clip
Lower
Shift Rod
Figure 9
Shift Arm
Assembly
Inside Hole
in Axle
Figure 8
•
•
Insert ferrule into the upper hole in shift lever.
Reinstall the hairpin clip and the washer.
IMPORTANT: Check for correct adjustment of the shift
lever as instructed on page 10, before operating the
snow thrower.
Click Pin
in Outside Hole
Skid Shoes
Figure 10
The space between the shave plate and the ground can
be adjusted. For close snow removal, place skid shoes
in the low position. Use middle or high position when
area to be cleared is uneven.
One Wheel Driving: Insert the click pin only
through the outside hole of the axle (not the rim) on
the right side of the snow thrower. This position
gives power drive to the left wheel only, making the
unit easier to maneuver.
Both Wheels Driving: Insert the click pin through
the hole in the hub of the rim and the inside hole on
the snow thrower’s right axle. This position is good
for heavy snow as there is power drive in both
wheels.
•
Adjust skid shoes by loosening the four hex nuts
and carriage bolts and moving skid shoes to
desired position. See WARNING:.
•
Make certain the entire bottom surface of skid shoe
is against the ground to avoid uneven wear on the
skid shoes. Retighten nuts and bolts securely.
WARNING: Do not operate this snow
thrower on gravel as loose gravel can be
easily picked up and thrown by the auger
causing injury to the operator and/or damage
to the snow thrower.
IMPORTANT: Never operate the snow thrower with the
click pin inserted through both the rim and the outside
hole in the axle. Doing so can result in serious damage
to the drive system.
Drive Wheels
The wheels may be adjusted for two different methods
of operation. The adjustment is made by placing the
click pins in one of two different holes on the right side
of the unit. See Figure 10.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 6: MAINTAINING YOUR SNOW THROWER
WARNING: Before servicing, repairing or
inspecting, disengage all clutch levers and
stop engine. Wait until all moving parts have
come to a complete stop. Disconnect spark
plug wire and ground it against the engine to
prevent unintended starting.
Shear Bolts
Lubrication
Engine
•
Refer to the engine manual for maintenance
procedures and instructions.
WARNING: When following instructions in
the engine manual for draining oil, be sure to
protect frame to avoid oil dripping onto
transmission parts.
Bearings
Bearings
Figure 11
Gear Shaft
Lubricate the gear shaft with a good all-weather
•
multi-purpose light grease at least once a season or
after every 25 hours of operation.
Klick Pin
Gear Case
The auger gearbox has been filled with grease at
•
the factory. If disassembled for repairs, lubricate
with 1-1/2 ounces of grease (part no. 737-0168).
IMPORTANT: Do not overfill the gear case. Damage to
the seals could result. Be sure the vent plug is free of
grease in order to relieve pressure.
Axle
Auger Shaft
•
At least once a season, remove shear bolts on
auger shaft. Oil or spray lubricant inside shaft. Also
lubricate the auger bearings at least once a season.
See Figure 11.
Figure 12
Drive and Shifting Mechanism
•
Remove rear cover. Oil any chains, sprockets,
gears, bearings, shafts, and shifting mechanism at
least once a season. Use engine oil or a spray
lubricant. Avoid getting oil on rubber friction wheel
and aluminum drive plate.
Chute Directional Control
•
The worm gear on the chute directional control
should be greased with multipurpose automotive
grease.
IMPORTANT: Keep all grease and oil off friction wheel
and drive plate.
Wheels
Oil or spray lubricant into bearings at least once a
•
season. Pull the klick pins and remove wheels,
clean and coat axles with a multipurpose
automotive grease. See Figure 12.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 7: SERVICE
•
•
Tip the snow thrower up and forward so that it rests
on the housing.
Remove six self-tapping screws from the frame
cover underneath the snow thrower. See Figure 13
for the location of the hardware.
WARNING: Before servicing, repairing, or
inspecting, disengage all clutch levers and
stop engine. Wait until all moving parts have
come to a complete stop. Disconnect spark
plug wire and ground it against the engine to
prevent unintended starting.
Belt
Cover
Augers
The augers are secured to the spiral shaft with two
shear bolts and hex lock nuts. If the snow thrower hits a
foreign object or ice jam, hex bolts will shear.
Self-Tapping
Screws
•
If the augers will not turn, check to see if the bolts
have sheared. Two replacement shear bolts and
hex lock nuts have been provided in the snow
thrower’s hardware pack. For future use, order part
number 710-0890A (shear bolt 5/16-18 x 1.5") and
712-0429 (hex lock nut 5/16-18).
Shave Plate and Skid Shoes
Figure 13
The shave plate and skid shoes on the bottom of the
snow thrower are subject to wear. They should be
checked periodically and replaced when necessary.
•
Roll the front and rear auger belts off the engine
pulley. See Figure 14.
•
To remove skid shoes, remove the four carriage
bolts, bell washers and hex nuts which attach them
to the snow thrower. Reassemble new skid shoes
with the four carriage bolts, bell washers (cupped
side goes against skid shoes) and hex nuts. Make
certain the skid shoes are adjusted to be level.
To remove shave plate, remove carriage bolts, bell
washers and hex nuts which attach it to the snow
thrower housing.
Drive
Belt
Rear Auger
Belt
Engine
Pulley
Front Auger
Belt
Idler
Pulley
•
•
Reassemble new shave plate, making sure heads
of the carriage bolts are to the inside of the housing.
Tighten securely.
Idler
Engine
Pulley
Pulley
Belt Replacement
Figure 14
WARNING: Disconnect the spark plug wire
from the spark plug and ground.
•
•
Unhook the idler spring from the hex bolt on the
auger housing. See Figure 15.
Back out the stop bolt to allow the belts to slip
between the bolt and auger pulley. See Figure 16.
Auger Belts
NOTE: It may be necessary to loosen the six hex nuts
that fasten the frame to the auger housing.
NOTE: It is necessary to remove both auger belts in
order to change either one. If changing just one belt, be
certain to check the condition of the other belt.
•
Lift the rear auger belt from the auger pulley, and
slip belt between the support bracket and the auger
pulley. See Figure 15. Repeat this step for front
auger belt .
•
Remove the plastic belt cover on the front of the
engine by removing the two self-tapping screws.
See Figure 13.
•
Replace both auger drive belts by following
instructions in reverse order.
•
Drain the gasoline from the snow thrower, or place
a piece of plastic under the gas cap.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
Drain the gasoline from the snow thrower, or place
a piece of plastic under the gas cap.
Tip the snow thrower up and forward, so that it rests
on the housing. See Figure 17.
Friction
Wheel
Support
Bracket
Hex Nut and
Bell Washer
Chute
Rear Auger
Belt
Frame
Note: The unit is
shown resting on
its auger housing
Auger
Front Auger
Pulley
Support
Bracket
Spring
Auger
Pulley
Figure 17
Auger
Idler
Spring
Housing
•
•
•
Remove the six self-tapping screws from the frame
cover underneath the snow thrower.
Remove the klick pins which secure the wheels,
and remove the wheels from the axle.
Using a wrench to hold the shaft, loosen, but do not
completely remove, the hex nut and bell washer on
left end of gear shaft. See Figure 17.
Figure 15
Drive Belt
•
•
Follow steps 1 through 4 of previous instructions.
Pull idler pulley up, and lift belt off engine pulley and
friction wheel disc. See Figure 14.
•
Lightly tap the hex nut to dislodge the ball bearing
from the right side of frame. Remove the hex nut
and bell washer from left end of shaft.
Slide the gear shaft to the right and slide the friction
wheel assembly from the shaft.
Remove the four screws from the friction wheel
assembly. Remove the friction wheel rubber from
between the plates. See Figure 18.
•
•
Back out the stop bolt until the support bracket rests
on the auger pulley. See Figure 16.
Slip belt between friction wheel and friction wheel
disc. Remove and replace belt. Reassemble
following the instructions in reverse order.
•
•
NOTE: The support bracket must rest on the stop bolt
after the new belt has been assembled. See Figure 25.
Friction
Wheel
Disc
Friction Wheel
Plates
Drive Belt
Bearing
Stop
Bolt
Screws
Hub
Friction Wheel Rubber
Figure 18
Support Bracket
•
•
Reassemble new friction wheel rubber to the
friction wheel assembly, tightening the four screws
in rotation and with equal force.
Position the friction wheel assembly up onto the pin
of the shift rod assembly, and slide the shaft
through the assembly. Reassemble the wheels and
the frame cover.
Figure 16
Changing Friction Wheel Rubber
The rubber on the friction wheel is subject to wear and
should be checked after 25 hours of operation, and
periodically thereafter. Replace the friction wheel
rubber if any signs of wear or cracking are found.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 8: OFF-SEASON STORAGE
•
•
Remove all dirt from exterior of engine and
equipment.
Follow lubrication recommendations on page 12.
WARNING: Never store engine with fuel in
tank indoors or in enclosed, poorly ventilated
areas where fuel fumes may reach an open
flame, spark or pilot light as on a furnace,
water heater, clothes dryer, or other gas
appliance.
NOTE: When storing any type of power equipment in
an poorly ventilated or metal storage shed, care should
be taken to rustproof the equipment, especially springs,
cables and all moving parts.
•
If unit is to be stored over 30 days, prepare the
engine for storage following instructions in the
engine manual.
SECTION 9: TROUBLE SHOOTING GUIDE
Trouble
Possible Cause(s)
Corrective Action
Engine fails to start Fuel tank empty, or stale fuel.
Fill tank with clean, fresh gasoline. Fuel may not last over thirty days
unless a fuel stabilizer is used.
Clean fuel line.
Move switch to ON position
Clean, adjust gap or replace.
Insert key.
Blocked fuel line.
Choke not in ON position
Faulty spark plug.
Key not in switch on engine.
Spark plug wire
Connect spark plug wire.
disconnected.
Primer button not depressed.
Fuel shut-off valve closed
(if so equipped).
Refer to the engine manual packed with your unit.
Open fuel shut-off valve.
Engine runs erratic Unit running on CHOKE.
Blocked fuel line or stale fuel.
Move choke lever to OFF position.
Clean fuel line; fill tank with clean fresh gasoline. Fuel may not last
over thirty days unless a fuel stabilizer is used.
Drain fuel tank. Refill with fresh fuel.
Refer to the engine manual packed with your unit or have carburetor
adjusted by an authorized service dealer.
Water or dirt in fuel system.
Carburetor out of adjustment.
Loss of power
Spark plug wire loose.
Gas cap vent hole plugged.
Exhaust port plugged.
Carburetor not adjusted
properly.
Connect and tighten spark plug wire.
Remove ice and snow from cap. Be certain vent hole is clear.
Clean-see Maintenance section of engine manual.
Refer to the engine manual packed with your unit or have carburetor
adjusted by an authorized service dealer.
Engine overheats
Incorrect fuel mixture.
Drain fuel tank. Refill with proper fuel mixture.
Excessive vibration Loose parts or damaged auger. Stop engine immediately and disconnect spark plug wire. Tighten all
bolts and nuts. Make all necessary repairs. If vibration continues, have
unit serviced by an authorized service dealer.
Unit fails to propel
itself
Incorrect adjustment of drive
cable.
Adjust drive cable. Refer to Adjustment section of this manual.
Drive belt loose or damaged.
Discharge chute clogged.
Replace drive belt. Refer to Belt Replacement on page 13.
Stop engine immediately and disconnect spark plug wire. Clean dis-
charge chute and inside of auger housing.
Unit fails to
discharge snow
Foreign object lodged in auger. Stop engine immediately and disconnect spark plug wire. Remove
Incorrect adjustment of drive
cable.
object from auger.
Adjust drive cable. Refer to Adjustment section of this manual.
Drive belt loose or damaged.
Shear bolt(s) sheared
Replace drive belt. Refer to Belt Replacement on page 13.
Replace shear bolt(s)
NOTE: For repairs beyond the minor adjustments listed above, contact your nearest authorized service dealer or
call 1-800-800-7310 for the Customer Support Center. Refer to separate engine manual packed with your snow
thrower for more engine related information.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 10: MODEL 31AE640F352 PARTS LIST
18
1
20
3
2
15
4
6
16
3
63
3
7
9
5
14
17
21
8
2
33
1
13
18
29
32
10
11
1
12
19
30
35
23
20
26
54
22
27
17
28
25
61
62
26
24
39
37
34
31
38
57
44
51
36
41
48
49
52
53
45
54
42
57
26
43
27
47
40
54
55
59
50
56
58
26
60
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Model 31AE640F352
REF.
NO.
1
2
3
4
5
6
7
PART
NO.
REF.
NO.
PART
NO.
DESCRIPTION
DESCRIPTION
Handle Panel (for top-mount lamp)
Saddle Washer
Bell Washer .340 ID x .872 OD
Lower Shift Rod
714-0507
747-0877
710-0599
784-5680
784-5679
748-0362
748-0363
732-0145
711-0653
Cotter Pin
Rod
33 731-1393
34 736-0451
35 736-0242
36 747-0621
37 726-0100
38 720-0201A
39 749-0953A
749-0952A
Hex Washer Screw 1/4-20 x .5
Handle Support Bracket — RH
Handle Support Bracket — LH
Cam Lock Handle
Handle Lock Pawl
Compression Spring
Clevis Pin
Push Cap
Chute Knob
Upper Handle — LH
Upper Handle — RH
Chute Crank
Chute Crank Eyebolt
Rubber Grommet
Shift Arm Assembly
Hex Washer Screw 1/4-20 x 1.0
Handle Tab
Lock Washer 5/16
Hex Cap Screw 5/16-18 x 1
Hex Cap Screw 5/16-18 x .75
Flat Washer
8
9
40 705-5204A
42 747-0697
43 735-0234
44 684-0008A
45 710-0788
46 784-5599
47 736-0119
48 710-0643
49 710-1880
50 736-0185
51 731-0921
52 731-1300B
53 712-3068
54 736-0159
55 710-0451
56 710-04071
57 720-0284
58 712-3027
59 731-0851A
60 710-3015
61 747-0620A
62 750-0963
63 625-0007
10 720-0232
11 684-0037B
12 784-5681
13 784-5619A
14 784-5682
15 732-0746
16 684-0036A
17 735-0199A
18 736-0509
19 712-0271
20 712-3010
21 746-0778
22 684-0103
23 712-3068
24 710-0449
25 712-0429
26 714-0104
27 736-0275
28 711-0677
29 710-0458
30 720-0274
31 749-0951
32 710-1003
Knob
Engagement Handle Assy — LH
Handle Support Bracket — LH
Shift Handle
Handle Support Bracket — RH
Torsion Spring
Engagement Handle Assy — RH
Rubber Bumper
Washer
Hex Nut 1/4-20 †
Hex Nut 5/16-18
Cable
Panel
Hex Lock Nut, 5/16-18
Carriage Screw 5/16-18 x 2.25
Hex Lock Nut, 5/16-18
Cotter Pin
Flat Washer 5/16
Ferrule
Carriage Screw 5/16-18 x 1.75
Grip
Lower Handle
Upper Chute
Lower Chute
Hex Lock Nut 5/16-18
5/16 Washer
Carriage Bolt 5/16-18 x .75
Carriage Screw 5/16-18 x 1.0
Knob
Hex Lock Nut 1/4-20
Flange Keeper
Hex Cap Screw 1/4-20 x .75
Upper Shift Rod
Rod Connector
Halogen Light Assembly
Hex Washer Screw
† Used with lamp ground wire
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Model 31AE640F352
27
20
39
38
Drive Clutch Cable
Auger Clutch Cable
5
37
4
13
30
7
6
40
45
3
4
30
5
2
14
36
26
15
16
25
44
9
7
10
11*
25
31
12
28
23
41
17
8
18
4
24
22
32
33
1
1
21
20
42
29
5
8
34
Auger Clutch Cable
19
43
35
1
1
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Model 31AE640F352
REF.
NO.
1
2
3
4
5
6
7
PART
NO.
REF.
NO.
PART
NO.
DESCRIPTION
Self-tapping Screw, 1/4-20 x .625
Drive Cable Guide Bracket
Auger Clutch Cable Bracket
Cable Roller
Hex Screw 1/4-28
Frame Assembly
Ball Bearing
Bell Washer
Lock Jam Nut
Hex Flange Bearing
Flat Washer†
Front Support Guide Bracket
Lock Hex Screw
Bell Washer .340 ID x .872 OD
Cotter Pin
Flat Washer .536 ID x .930 OD
Self-tapping Screw, 1/4-20 x 1.25
Frame Shift Bracket
Frame Cover
Hex Washer TT Screw 1/4-20
Flat Washer .760 ID x .50 OD
Gear
DESCRIPTION
7-Tooth Shaft
Roll Pin
Klik Pin
Friction Wheel Assembly
Friction Disc Wheel
Wheel Shift Rod Assembly
Self-tapping Screw, 1/4-20 x .5
Spacer
Friction Wheel Bracket Assembly
Extension Spring
Jam Nut 3/8-24
Drive Cable
Axle 16” Wheels
Friction Plate
Friction Wheel Rubber
Friction Wheel Hub
Friction Wheel Bearing
Clevis Pin, 1/4 x 1.3725
Flat Washer, .281 x .5 x .063
Cotter Pin, .75
710-1652
784-5688
784-5687A
756-0625
738-0924
784-5630B
741-0563
736-0105
712-0116
24 717-1444
25 715-0249
26 714-0143
27 684-0042B
28 656-0012A
29 684-0013B
30 710-0599
31 748-0190
32 684-0021
33 732-0264
34 712-0711
35 746-0898B
36 738-0830
37 790-00010
38 735-0243B
39 718-0301A
40 618-0063A
41 711-1364
42 736-0142
43 714-0507
44 712-0703A
45 790-00011
8
9
10 741-04026
11 736-0188
12 784-5689A
13 710-0538
14 736-0242
15 714-0474
16 736-0160
17 710-0809
18 784-5590
19 784-5638
20 710-1652
21 736-0351
22 717-1445
23 714-0126
Insert Nut, 5/16-18
Friction Plate (Exterior)
Key
† Use more than one washer on either side, only if necessary to reduce axle-play.
2
1
WHEEL CHART
MODEL
NUMBER
31AE640F352
WHEEL
SIZE
16 x 4.8
REF. NO. 1
SPACER
731-04043
REF. NO. 2
WHEEL ASS’Y*
734-1709A
TIRE
ONLY
734-1530
AIR
VALVE
734-0255
RIM
ONLY
734-1708A
SLEEVE
BEARING (2)
741-0401
* Wheel assembly includes one tire, one air valve, one painted rim and two sleeve bearings
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Model 31AE640F352
2
3
4
9
1
44
11
10
43
14
12
5
9
6
24
8
7
18
19
20
22
9
15
23
10
21
27
13
13
38
25
28
23
18
13
26
30
35
41
22
36
18
9
33
18
9
37
40
34
40
39
16
39
42
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Model 31AE640F352
REF.
NO.
PART
NO.
DESCRIPTION
Lock Jam Nut 3/8-24
1
712-0116
2
3
4
5
6
7
8
9
756-0178
784-5632B
710-0459A
738-0281
736-0167
732-0611
712-3068
712-3010
Flat Idler
Auger Idler Arm
Hex Cap Screw 3/8-24 x 1.50
Shoulder Screw
Flat Washer, .565 x 1.25 x .02
Extension Spring
Hex Nut 5/16-18
Hex Nut 5/16-18
Lock Washer 5/16
Housing
10 736-0119
11 05931A
12 741-0309
13 710-0451
14 705-5226
15 684-0040D
16 784-5618
18 736-0242
19 741-0475
20 784-5647
21 731-1379C
22 712-0324
23 736-0463
24 731-2635
25 710-0703
26 710-0604A
27 736-0169
28 712-0798
30 784-5580
31 731-2643
32 731-2635
33 784-5579A
34 741-0245
35 684-0065
36 715-0114
37 712-0429
38 605-5192A
39 736-0188
40 741-0493A
41 605-5193A
42 710-0890A
43 746-0897
44 731-2643
Ball Bearing
Carriage Bolt 5/16-18 x .75
Reinforcement Chute
26” Housing Assembly
Bearing Housing
Bell Washer
Bushing
Chute Crank Bracket
Chute Adapter
Hex Lock Nut 1/4-20
Flat Washer
Mount, Chute Clean-out Tool
Carriage Screw 1/4-20 x .75
Hex Washer TT Screw 5/16-18
Lock Washer 3/8
Hex Nut 3/8-16
Snow Shoe
Chute Clean-out Tool
Mount, Chute Clean-out Tool
26” Shave Plate
Hex Flange Bearing
Impeller Assembly
Pin
Lock Nut 5/16-18
Spiral 26” RH
Flat Washer
Flange Bushing
Spiral 26” LH
Shear Bolt 5/16-18 x 1.5
Drive Cable
Chute Clean-out Tool
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Model 31AE640F352
4
17
11
9
16
13
8
15
2
10
14
5
6
3
7
12
3
1
REF.
NO.
1
PART
NO.
618-0123
DESCRIPTION
RH Reducer Housing
LH Reducer Housing
Hex Screw 1/4-20 x .75
Spiral Axle 26"
Key
Pin-Spiral
Worm Gear, 20T
Worm Shaft
Thrust Collar
Grease Plug
Grease Seal
Flat Washer .76 x 1.5 x .030
Flat Washer .508 x 1.0 x .020
Flat Washer .76 x 1.5 x .060
Flange Bearing .75 x 1.0 x .59
Flange Bearing .75 x 1.0 x .925
Gearbox Ass’y. Complete 26"
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
618-0124
710-0642
711-0909A
714-0161
715-0143
717-0528
717-0526
718-0186
721-0325
721-0327
736-0351
736-0369
736-0445
741-0662
741-0663
618-0121A
NOTE: NOTE: When rebuilding a gearbox assembly, include 1.5 oz. of Alvania EP Lead-Free Grease (Part No. 737-0168)
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Model 31AE640F352
1
IMPORTANT: For a proper working machine, use Factory Approved Parts.
V-BELTS are specially designed to engage and disengage safely. A substitute
(non OEM) V-Belt can be dangerous by not disengaging completely.
2
3
5
4
8
26
9
10
11
12
15
16
19
16
7
16
4
19
6
16
21
22
13
14
17
18
25
23
20
20
24
REF.
NO.
1
2
3
4
5
6
7
PART
NO.
REF.
NO.
PART
NO.
DESCRIPTION
Hex Washer Screw 1/4-20 x .625
Belt Cover
Extension Spring
Hex Screw 5/16-24 x .75
Hex Cap Screw 3/8-16 x 1.25
Drive Clutch Idler Bracket
Shoulder Spacer
Pulley Half
DESCRIPTION
Lock Hex Cap Screw 5/16-24
Lock Jam Nut 3/8-16
Pulley Half
Bell Washer
Flat Washer
Belt
Auger Pulley
Flat Washer 3/8 x 1.25 OD
Bell Washer
Hex Cap Screw 3/8-24
Pulley Adapter
710-1652
731-1324
732-0710
710-0627
710-3005
05896A
748-0234
756-0987
754-0346
14 710-1245A
15 712-0181
16 756-0569
17 736-0242
18 736-0505
19 754-0430A
20 756-0967
21 736-0247
22 736-0331
23 710-0696
24 748-0360
25 710-0654A
26 629-0071
8
9
V-Belt
Pulley Half
10 756-0986
11 736-0270
12 710-0230
13 756-0313
Bell Washer
Hex Cap Screw 1/4-28 x .50
Flat Idler
Hex Screw 3/8-16 x 1.0
Extension Cord, Three-Prong
23
Download from Www.Somanuals.com. All Manuals Search And Download.
MANUFACTURER’S LIMITED WARRANTY FOR:
The limited warranty set forth below is given by MTD LLC with
respect to new merchandise purchased and used in the
United States, its possessions and territories.
d. MTD LLC does not extend any warranty for products
sold or exported outside of the United States, its posses-
sions and territories, except those sold through MTD
LLC’s authorized channels of export distribution.
e. Parts that are not genuine MTD parts are not covered by
this warranty.
MTD LLC warrants this product against defects for a period of
two (2) years commencing on the date of original purchase
and will, at its option, repair or replace, free of charge, any
part found to be defective in materials or workmanship. This
limited warranty shall only apply if this product has been oper-
ated and maintained in accordance with the Operator’s Man-
ual furnished with the product, and has not been subject to
misuse, abuse, commercial use, neglect, accident, improper
maintenance, alteration, vandalism, theft, fire, water, or dam-
age because of other peril or natural disaster. Damage result-
ing from the installation or use of any accessory or
f.
Service completed by someone other than an authorized
service dealer is not covered by this warranty.
g. Transportation charges and service calls are not
covered.
No implied warranty, including any implied warranty of
merchantability of fitness for a particular purpose,
applies after the applicable period of express written
warranty above as to the parts as identified. No other
express warranty, whether written or oral, except as men-
tioned above, given by any person or entity, including a
dealer or retailer, with respect to any product, shall bind
MTD LLC. During the period of the warranty, the exclu-
sive remedy is repair or replacement of the product as
set forth above.
attachment not approved by MTD LLC for use with the prod-
uct(s) covered by this manual will void your warranty as to
any resulting damage.
Normal wear parts or components thereof are subject to sep-
arate terms as follows: All normal wear parts or component
failures will be covered on the product for a period of 90 days
regardless of cause. After 90 days, but within the two year
period, normal wear part failures will be covered ONLY IF
caused by defects in materials or workmanship of OTHER
component parts. Normal wear parts and components
include, but are not limited to: batteries, belts, blades, blade
adapters, grass bags, rider deck wheels, seats, snow thrower
skid shoes, shave plates, auger spiral rubber, tires.
The provisions as set forth in this warranty provide the
sole and exclusive remedy arising from the sale. MTD
LLC shall not be liable for incidental or consequential
loss or damage including, without limitation, expenses
incurred for substitute or replacement lawn care services
or for rental expenses to temporarily replace a warranted
product.
HOW TO OBTAIN SERVICE: Warranty service is available,
WITH PROOF OF PURCHASE, through your local autho-
rized service dealer. To locate the dealer in your area, check
your Yellow Pages, or contact MTD LLC at P.O. Box 361131,
Cleveland, Ohio 44136-0019, 1-800-800-7310, 1-330-220-
Some states do not allow the exclusion or limitation of inci-
dental or consequential damages, or limitations on how long
an implied warranty lasts, so the above exclusions or limita-
tions may not apply to you.
In no event shall recovery of any kind be greater than the
amount of the purchase price of the product sold. Alteration
of safety features of the product shall void this warranty.
You assume the risk and liability for loss, damage, or injury to
you and your property and/or to others and their property
arising out of the misuse or inability to use the product.
This limited warranty does not provide coverage in the follow-
ing cases:
a. The engine or component parts thereof. These items
carry a separate manufacturer’s warranty. Refer to the
applicable manufacturer’s warranty for terms and condi-
tions.
This limited warranty shall not extend to anyone other than
the original purchaser or to the person for whom it was pur-
chased as a gift.
b. Log splitter pumps, valves, and cylinders have a sepa-
rate one year warranty.
c. Routine maintenance items such as lubricants, filters,
blade sharpening, tune-ups, brake adjustments, clutch
adjustments, deck adjustments, and normal deterioration
of the exterior finish due to use or exposure.
HOW STATE LAW RELATES TO THIS WARRANTY: This
limited warranty gives you specific legal rights, and you
may also have other rights which vary from state to state.
MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019 1-800-800-7310
Download from Www.Somanuals.com. All Manuals Search And Download.
|