MTD Lawn Mower OEM 190 625 User Manual

Operator’s Manual  
Twin Rear Bagger  
For Revolution and ZTT Model Lawn Tractors  
Models  
OEM-190-625 (for 42-inch decks)  
OEM-190-626 (for 46-inch decks)  
MTD PRODUCTS INC. P.O. BOX 368022 CLEVELAND, OHIO 44136-9722  
770-10442
FORM NO.  
(8/2000)  
PRINTED IN U.S.A.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECTION 1: TO THE OWNER  
Model 625 and Model 626 Twin Rear Bagger Kits are grass collection systems designed for use on Revolution and  
ZTT Model Lawn Tractors equipped either a 42-inch cutting deck (Model 625) or a 46-inch cutting deck (Model 626)  
only. It will NOT fit on any other tractor, regardless of the tractor’s FastAttach compatibility.  
The instructions in this manual are divided into sections. Carefully read all sections and study the illustrations to  
ensure proper installation and usage of this attachment. Read and observe all WARNING statements. They are  
included to provide for the protection of the equipment installer and user, and to ensure the prolonged service life of  
the equipment.  
NOTE: References to LEFT and RIGHT indicate the left and right sides of the tractor when facing forward in the  
operator’s position. Reference to the FRONT indicates the grille end; to the REAR the drawbar end.  
SECTION 2: CONTENTS OF CARTON  
Before beginning installation, remove all parts from the carton to make sure everything is present. Carton contents  
are listed below and shown in . Hardware part number are shown in parentheses.  
One Chute Tube  
Two Grass Bag Assemblies  
One Discharge Tube Assembly  
One Set of Blades (Model 626 only)  
One Extension Tube  
One Grass Catcher Cover Assembly  
One Bracket Assembly w/ Clevis Pin (711-0309A)  
& Hairpin Clip (714-0117) in place.  
Cover Assembly  
Chute Tube  
Support Tube  
(attached to cover)  
Bracket Assembly  
Blades  
(Model 626 Only)  
Extension  
Tube  
Bag Assemblies  
Discharge Chute  
Assembly  
Figure 2  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECTION 3: ATTACHING THE GRASS COLLECTOR  
WARNING: Before attempting to install the grass collector, move the machine to flat, level ground,  
disengage PTO, move control handles into neutral position, set parking brake, stop engine and remove  
key to prevent unintended starting.  
Support Tube Rests Here  
Insert Support Tube Here  
Bracket Assembly  
Clevis Pin  
Hairpin Clip  
Shoulder Bolt  
Figure 3  
3. Attach the grass bags using the slots as shown in  
Mounting the Bracket Assembly  
Figure 4.  
1. To ease the following procedures, pivot the seat  
forward and leave it in that position until the grass  
collector is fully mounted and assembled.  
2. Remove the hairpin clip and clevis pin from the rear  
of the bracket assembly. Refer to Figure 3  
3. Position the hooked ends of the bracket assembly  
to the outside of the hitch plate and over the  
shoulder bolts. Refer to Figure 3.  
4. Reinsert the clevis pin through the aligned holes in  
both the bracket assembly and the hitch plate and  
secure with the hairpin clip. Refer to Figure 3.  
Slots  
IMPORTANT: There are two holes in the clevis pin. Be  
sure to insert the hairpin clip in the upper hole to  
properly secure the bracket assembly to the hitch plate.  
Slots  
Attaching the Cover and Bags  
1. Place the cover assembly’s support tube (refer to  
Figure 2) in position on the rear of unit by sliding the  
support tube down through the holes in the left side  
of the bracket assembly. Use the inside hole on the  
bracket assembly regardless of what size deck  
your tractor is equipped with. Refer to Figure 3.  
2. Place the cover assembly in position so that the  
support tube rests on the right side of the bracket  
assembly. Refer to Figure 3. Allow the plastic cover  
to rest in the “open” position on the back of the  
tractor’s seat until Step 3 is completed.  
Figure 4  
4. Close the cover on the grass collector.  
Attaching The Cutting Blades  
(Model 626 Only)  
WARNING: Protect your hands by using  
heavy gloves or a rag to grasp the cutting  
blade.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remove the blades from your tractor’s cutting deck as  
follows.  
Hex Flange Nut  
Wood Block  
NOTE: Do NOT perform the following steps on  
tractor’s equipped with a 42-inch deck.  
1. Remove the cutting deck from beneath the tractor,  
(refer to Deck Removal in the MAINTENANCE section of  
your tractor’s Operator’s Manual for detailed  
instructions) then gently flip the deck over to  
expose its underside.  
2. Place a block of wood between the center deck  
housing baffle and the cutting blade to act as a  
stabilizer. See Figure 5.  
3. Use a 15/16" wrench to remove the hex flange nut  
that secures the blade to the spindle assembly. See  
Figure 5.  
Spindle Assembly  
NOTE: The hex flange nut has a normal (right-  
handed) thread pattern. Do NOT attempt to force the  
nut in the incorrect direction. Doing so may damage the  
nut and create a safety hazard.  
Figure 5  
Figure 6  
Figure 7  
4. Install the new blades packed with the bagger. Be  
sure to install the blade with the side of the blade  
marked ‘‘Bottom’’ (or with a part number stamped in  
it) facing the ground when the mower is in the  
operating position.  
IMPORTANT:Mount the SMALLER of the three blades to  
the CENTER spindle. The remaining two blades are  
interchangeable.  
IMPORTANT:Use a torque wrench to tighten the blade  
spindle hex flange nut to between 70 foot-pounds and  
90 foot-pounds.  
5. Remount the cutting deck.  
Discharge Chute  
Retainer Strap  
Attaching the Discharge Chute  
1. Raise the deck to its highest position by placing the  
lift lever in the top notch on the right fender.  
2. Pivot the chute deflector on the deck upward.  
3. Place the top edge of the discharge chute in  
position over the chute opening on the deck, then  
push down on the discharge chute so the front  
edge fits snugly around the cutting deck opening.  
See Figure 6.  
4. Fasten the discharge chute in position by hooking  
the retainer strap over the retainer clip found on the  
front lip of the cutting deck. See Figure 6.  
5. Pivot the cover assembly forward and insert the  
upper end of the chute tube into the hole in the  
cover assembly. See Figure 7.  
6. Insert the extension tube between the discharge  
chute and the chute tube as shown in Figure 7.  
7. Secure by placing the ends of the retainer straps on  
the discharge chute over the clips on the chute  
tube. See Figure 7.  
Chute Tube  
Extension Tube  
Retainer Strap  
Discharge Chute  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Models 625 & 626  
5
1
28  
2
24  
14  
4
5
10  
5
14  
24  
3
17  
22  
24  
17  
26  
17  
7
8
22  
9
30  
24  
9
24  
9
24  
27  
9
6
13  
32  
11  
12  
21  
25  
20  
17  
19  
23  
29  
31  
37  
18  
15  
35  
16  
33  
36  
34  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Models 625 & 626  
REF.  
NO.  
1
PART NO.  
16847A  
DESCRIPTION  
Screen Assembly  
2
3
16596  
Hinge Bracket Assembly  
Grass Catcher Cover (Model 625)  
Grass Catcher Cover (Model 626)  
Plastic Plate, 1/8 x 5.6 sq.  
Zip Twist Fastener  
Tube Seal (Model 625)  
Tube Seal (Model 626)  
U-Type Speed Nut, #10-24  
Screw, #10-24 x .5  
Hex Screw, 1/4-20 x .5 (Model 625)  
Hex Screw, 1/4-14 x ..625 (Model 626)  
Cover Assembly (Model 626)  
Cover Assembly (Model 626)  
Catcher Support Tube Mounting Bracket  
Bag Frame Hanger Bracket  
Catcher Support Tube Assembly  
Retainer Hook Bracket  
731-0821A  
731-1417  
731-0824A  
726-0258  
723-0412  
723-0413  
712-0147  
710-0473  
710-0599  
710-0896  
4
5
6
7
8
9
10 16594A  
631-0007  
11 16587D  
12 16591A  
13 16592  
14 16606  
15 710-0473  
16 710-0604A  
17 710-0751  
18 710-3008  
19 711-0309A  
20 712-0272  
21 712-0431  
22 723-0476  
23 712-3004A  
24 712-3027  
25 714-0117  
26 723-0383  
27 731-0827B  
731-0925B  
28 731-0899A  
731-0926  
29 736-0253  
30 731-3272  
731-2299  
31 738-0380  
32 783-1079  
33 749-0701A  
34 764-0221  
35 783-0601  
36 742-0644  
37 742-0645  
Screw, #10-24 x .5  
Self Tapping Screw, 5/16-18 x .625  
Hex Cap Screw, 1/4-20 x .62  
Hex Cap Screw, 5/16-18 x .75  
Clevis Pin  
Hex Sems Nut, 10-24  
Hex Flange Lock Nut, 3/8-16  
Retainer Strap Assembly  
Hex Flange Lock Nut, 5/16-18  
Hex Flange Lock Nut, 1/4-20  
Internal Cotter Pin, .148 x 3  
Retainer Strap Assembly  
Discharge Chute (Model 625)  
Discharge Chute (Model 626)  
Chute Tube (Model 625)  
Chute Tube (Model 626)  
Bell Washer  
Extension Tube (Model 625)  
Extension Tube (Model 626)  
Shoulder Screw, .50 x .27, 3/8-16  
Catcher Support Bracket  
Bag Frame Tube  
Bag  
Catcher Support Bracket  
Star Center Blade, 16.28 (Model 626)  
Star Center Blade, 14.88 (Model 626)  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
MANUFACTURERS  
LIMITED WARRANTY  
c. Routine maintenance items such as lubricants, filters,  
The limited warranty set forth below is given by MTD  
PRODUCTS INC (MTD) with respect to new merchandise  
purchased and used in the United States, its possessions  
and territories.  
blade sharpening and tune-ups, or adjustments such  
as brake adjustments, clutch adjustments or deck  
adjustments; and normal deterioration of the exterior  
finish due to use or exposure.  
d. MTD does not extend any warranty for products sold  
or exported outside of the United States of America,  
its possessions and territories, except those sold  
through MTDs authorized channels of export distribu-  
tion.  
MTD warrants this product against defects in material and  
workmanship for a period of two (2) years commencing on  
the date of original purchase and will, at its option, repair or  
replace, free of charge, any part found to be defective in  
material or workmanship. This limited warranty shall only  
apply if this product has been operated and maintained in  
accordance with the Operators Manual furnished with the  
product, and has not been subject to misuse, abuse, com-  
mercial use, neglect, accident, improper maintenance,  
alteration, vandalism, theft, fire, water or damage because  
of other peril or natural disaster. Damage resulting from the  
installation or use of any accessory or attachment not  
approved by MTD Products Inc. for use with the product(s)  
covered by this manual will void your warranty as to any  
resulting damages.  
No implied warranty, including any implied warranty of  
merchantability or fitness for a particular purpose,  
applies after the applicable period of express written  
warranty above as to the parts as identified. No other  
express warranty or guaranty, whether written or oral,  
except as mentioned above, given by any person or  
entity, including a dealer or retailer, with respect to any  
product shall bind MTD. During the period of the War-  
ranty, the exclusive remedy is repair or replacement of  
the product as set forth above. (Some states do not  
allow limitations on how long an implied warranty lasts, so  
the above limitation may not apply to you.)  
Normal wear parts or components thereof are subject to  
separate terms as follows: All normal wear part or compo-  
nent failures will be covered on the product for a period of  
90 days regardless of cause. After 90 days, but within the  
two year period, normal wear part failures will be covered  
ONLY IF caused by defects in material or workmanship of  
OTHER component parts. Normal wear parts and compo-  
nents include, but are not limited to, belts, blades, blade  
adapters, grass bags, rider deck wheels, seats, snow  
thrower skid shoes, shave plates and tires. Batteries are  
covered by a 90-day limited replacement warranty.  
The provisions as set forth in this Warranty provide the  
sole and exclusive remedy arising from the sales. MTD  
shall not be liable for incidental or consequential loss  
or damages including, without limitation, expenses  
incurred for substitute or replacement lawn care ser-  
vices, for transportation or for related expenses, or for  
rental expenses to temporarily replace a warranted  
product. (Some states do not allow the exclusion or limita-  
tion of incidental or consequential damages, so the above  
exclusion or limitation may not apply to you.)  
HOW TO OBTAIN SERVICE: Warranty service is available,  
WITH PROOF OF PURCHASE THROUGH YOUR LOCAL  
AUTHORIZED SERVICE DEALER. To locate the dealer in  
your area, please check for a listing in the Yellow Pages or  
contact the Customer Service Department of MTD PROD-  
UCTS INC by calling 1-800-800-7310 or writing to P.O. Box  
368022, Cleveland, Ohio 44136-9722.  
In no event shall recovery of any kind be greater than the  
amount of the purchase price of the product sold. Alteration  
of the safety features of the product shall void this War-  
ranty. You assume the risk and liability for loss, damage, or  
injury to you and your property and/or to others and their  
property arising out of the use or misuse or inability to use  
the product.  
This limited warranty does not provide coverage in the  
following cases:  
a. The engine or component parts thereof. These items  
carry a separate manufacturers warranty. Please refer  
to the applicable manufacturers warranty on these  
items.  
This limited warranty shall not extend to anyone other than  
the original purchaser, original lessee or the person for  
whom it was purchased as a gift.  
b. Log splitter pumps, valves and cylinders have a sepa-  
rate one year warranty.  
How State Law Relates to this Warranty: This limited  
warranty gives you specific legal rights, and you may also  
have other rights which vary from state to state.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Moxa Technologies Switch UC 7400 User Manual
Multiquip Portable Generator dca 70usj User Manual
NEC Server N8100 1061F User Manual
Nikon Film Camera FE User Manual
Nortel Networks Answering Machine P0857846 User Manual
Olympus Microcassette Recorder V406171SU000 User Manual
Opticon Scanner OPR 3001 User Manual
Panasonic Car Amplifier CY PA4003U User Manual
Panasonic Network Card 2SB0792A User Manual
Panasonic Telephone Accessories KX DT390 User Manual