REGATTA™ 2
Synthesized Marine Transceiver
VHF/FM 25/1 Watt
Models RG2W or RG2B
Page 1
Download from Www.Somanuals.com. All Manuals Search And Download.
9.4 “ Log” (list of registered calls)....................................................23
9.5 “Dir” (Entries in the directory) ....................................................23
9.6 “Posn”(Setting of position co-ordinates and adjustment of UTC time)
24
9.7 ”LCD” (display contrast) ............................................................24
9.8 “Beep” (Enable/disable keypad beep) .......................................24
9.9 “ZONE”(Adjustment of UTC time deviation) ..............................25
9.10 MMSI (Setting of personal MMSI code and MMSI group code).25
10 MAINTENANCE.............................................................................25
10.1 Maintenance and warnings .......................................................25
11 TROUBLESHOOTING ...................................................................26
12 TECHNICAL SPECIFICATIONS:...................................................27
12.1 Transmitter................................................................................27
12.2 Receiver....................................................................................27
13 FREQUENCY TABLE ....................................................................28
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
with current regulations. Not following these instructions can cause personal
injury and/or malfunction of the device.
1
ABOVE ALL... SAFETY!
,
,
Do not use REGATTA 2 before connecting a suitable antenna that is in perfect
working condition – although REGATTA 2 is protected, this may seriously damage
the stages of transmission power.
1.1
Symbols used
For ease and convenience of viewing, REGATTA 2 uses symbols to highlight urgent
situations, practical advice, and general information.
Do not use transmit before ensuring proper connection of the antenna. During
transmission, remain at a minimum distance of 3 feet from the antenna.
,
Warnings such as this, shown using an open hand symbol, indicate a crucial
description regarding technical repairs, dangerous conditions, safety warnings,
advice and/or important information. Ignoring these symbols may result in serious
problems and/or damage and/or personal injury.
1.2b Environmental
,
Pay attention to ambient conditions – although REGATTA 2 is designed to operate
under the most severe conditions, it is important to avoid exposure to
environments that are excessively humid or dusty, or to temperatures outside the
+5°F to +55°F range. Also avoid exposure to direct sunlight.
ꢀ
Notes such as this one indicate practical advice that we suggest be followed for optimal
performance with REGATTA 2.
,
,
Avoid jarring and excessive vibration – REGATTA 2 is built to resist mechanical
shock and vibration as long as these are within the norm for any electrical device.
1.2
Warnings
Do not use this device in potentially explosive environments. A single spark may
cause an explosion.
1.2
General
,
This device has been tested for compliance with Class D digital marine device
limits. These limits were created to allow for reasonable protection against
damaging interference.
1.3
Registration of your Marine Transceiver
For using GMDSS and DSC functions, the operator must have a GMDSS radio
operator’s certificate (SRC or LRC) and apply for a ships MMSI number at the local
radio authority. Without MMSI number the radio can only be used as conventional
VHF marine radio without DSC. Your distributor may program your radio according
to your needs.
,
,
,
This device is to be used solely as an aid to navigation. Its settings may be
influenced by diverse factors, such as defects or malfunction of the device,
environmental conditions or improper use.
It is the user’s responsibility to observe reasonable prudence and judgement in
navigation, and as such this device should not be considered a substitute for this
reasonable prudence and judgement.
Do not open the radio for any reason! REGATTA 2’s precision mechanics and
electronics require expertise and specialized equipment; for the same reason, the
radio should under no circumstances be realigned as it has already been calibrated
for maximum performance. Unauthorized opening of the transceiver will nullify the
warranty.
1.2a Radio Frequency / Installation
,
Midland recommends following the requirements for prevention of radio frequency
exposure. Unauthorized changes or modifications to this device may invalidate
conformity to the FCC Regulations. All changes or modifications must be approved
in writing by MIDLAND RADIO CORPORATION.
,
This VHF DSC transceiver generates and irradiates electromagnetic energy (EME)
at radio frequency (RF), and as such must be installed and placed in operating
conditions that are in conformity with the instructions contained in this manual and
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
____________________________________________
1.4
Assistance
We urge you to write the serial number of your transceiver in the space provided
below. This number is found on the back panel of the transceiver and will be useful
in the event of repair/assistance and/or loss and/or theft.
IN CASE OF EMERGENCY
If you have need of assistance, contact other vessels and the Coast guard by
sending a distress signal on Channel 16.
NOTE
.
USING CHANNEL 16
DISTRESS CALL PROCEDURE
1. “MAYDAY MAYDAY MAYDAY.”
2. “THIS IS ………….” (name of vessel)
3. Your callsign or other indication of the vessel (and 9-digit DSC
ID if you have one.
A WARNING STICKER is supplied with this transceiver. To comply
with FCC regulations, this sticker must be affixed in such a location
as to be readily seen from the operating controls of the radio as in the
diagram below. Make sure the chosen location is clean and dry
before applying the sticker.
4. “LOCATED AT …………” (your position)
5. The nature of the distress or assistance required.
6. Any other information which might facilitate the rescue.
Or transmit your distress call using Digital Selective Calling on channel 70.
USING DIGITAL SELECTIVE CALLING (ch70)
DISTRESS CALL PROCEDURE
1. While holding aside the key cover, press the DISTRESS key.
2. Repeat pressing soft key “Undefined” to select the type of
distress.
3. Holding aside the key cover, press and hold the DISTRESS key
for 5 seconds until you have heard 5 beeps.
4. Wait for an acknowledgement from a coast station. Channel
16 is automatically selected.
5. Press PTT and transmit the information listed above.
1.5
Manual Notes
Writing of this manual has been completed with the intention of supplying information
that is comprehensive, precise and up-to-date. Nevertheless, Midland does not
assume responsibility for the actual correspondence with the product and for the
consequences of possible errors caused by factors over which it has no control.
Equipment and options described may differ according to varying countries.
Serial number _______________________
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
General
Congratulations for choosing Midland’s REGATTA™ 2 marine transceiver. This
product is a high performance, mobile VHF DSC marine transceiver. The following
are its principle features:
•
•
Equipped with all international channels available (correctly assigned).
High transmission power of 25W, which allows the user to maintain contact
from large distances, and a low transmission power of 1 W to reduce power
consumption during short-distance communication and for in harbor use.
•
•
•
•
•
Principal commands duplicated on the microphone for faster accessibility –
channel selection and channel 16 recall.
Backlit LCD display and adjustable contrast – constantly shows REGATTA
2’s parameters and settings on an easy-to-read display.
Extraordinary capability for water resistance, conforms with the standard
IP54.
Recall button for Channel 16 – for instant access to channel 16 (the universal
marine channel for emergency contact).
NMEA connection – use the interface cable supplied for easy connection from
transceiver to optional GPS system. Once connected, the display will show the
automatically updated coordinates (latitude and longitude) and time data.
•
•
•
•
DSC Digital Selective Calling – for security on the water and the ability to
make quick calls automatically.
MMSI directory, which simplifies the sending of DSC calls to frequently called
contacts and allows viewing of contact name on the display.
Mounting on adjustable bracket for stable and comfortable positioning in any
condition.
Connection to an external speaker (optional) – for listening to
communications further away from the transceiver.
ꢀ
In an effort to constantly improve product quality, product characteristics are subject to
authorized dealer.
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
(5) FUNCTION keys
2
DESCRIPTION OF CONTROLS AND
CONNECTORS
They enable to enter into the menu pages, to activate some functions such as Triple
Watch or SCAN.
(6) H/L
2.1. Front panel
Push the H/L button to select high transmission power (25W) or low power (1W).
The LCD display will show HI(high power) or LO(low power).
The H/L function is accessible in normal VHF or MEM mode.
(7)
(Backlight)
button down to activate the display and keypad backlight (“LITE”
Hold the
appears on the display). You can select 4 different backlight levels.
(8) D/W (Dual Watch)
This button activates the Dual Watch function, able to search the tuned channel and
channel 16 alternatively.
(9) Emergency Channel 16
Pressing the 16 button provides quick access to the emergency channel.
(10) DISTRESS button
The button below a soft cover sends a DISTRESS call for help. The signal also
includes your MMSI identification code and the nature of the distress. If a GPS is
connected to the device, data regarding position and time are also included in the
call. For further details, see paragraph 8.7.
(1) ON/OFF/VOLUME
ꢀ
The Distress function, or any other DSC transmission function, is not operative until a
MMSI user code has been inserted.
Turns REGATTA 2 on/off and regulates audio volume reception. The radio is turned
off when you completely rotate the knob counter-clockwise until it clicks.
(11) LCD Display
(2) SQUELCH
The large LCD (liquid crystal) display constantly shows the operating status of the
radio as well as being a function guide with the easy-to-read dot matrix area.
Regulates the squelch level (noise silencer in absence of signals).
(12) Internal speaker
(3) MICROPHONE jack
Provides crystal clear sound.
Insert the mike connector into this jack.
(4) Alphanumeric keypad
The keypad gives the possibility to select channels, to add your own MMSI
identification code and to activate/deactivate many other functions described in the
following pages.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2
Back panel (connections)
,
Warning! Faulty connections or short-circuits may seriously damage REGATTA 2.
Before attempting any connections, consult the specialized sections of this
manual.
1) Antenna Jack
This SO 239 jack is for connecting an appropriate antenna.
2) Power cable
This red/black cable has to be connected to a power source of 12 V DC (red is
positive. Attention: A converter is needed for 24 V power sources!
3) Jack for additional external loudspeaker
You can use this jack for the connection to a suitable external loudspeaker
(optional), if needed.
4) GPS connector
Allows for connection to the optional receiver module for obtaining, viewing and
transmitting (with DSC) information regarding position and current time data.
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
2.3. Microphone
(1) UP and DOWN buttons These two buttons change the tuning channel.
The first scrolls upwards through the tuned marine channels, the second
scrolls downwards.
(2) Button 16
For ease of use, button 16 performs the same function as button 16 on the front
panel of the transceiver.
(3) PTT (push to talk)
Pressing this button will begin transmission.
(4) Microphone
During transmission, speak with the microphone a few inches away from your face.
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
3.
INSTALLATION
3.1
Contents of package
Before using your transceiver, ensure that your package is complete and contains:
(1) Mounting bracket
(2) DC power cord with integrated protecting fuse
(3) Knobs (2 pieces)
(4) Mounting piece for microphone
(5) Self-threading screws for mounting bracket (4 pieces)
(6) Screws for mounting bracket (4 pieces)
(7) Washers (4 pieces)
(8) Grained washers (4 pieces)
(9) Nuts (4 pieces)
(10) Self-threading screws for microphone mount (2 pieces)
(11) Screws for the microphone mount (2 pieces)
(12) Washers (2 pieces)
3.2 Location for the transceiver
(13) Grained washers (2 pieces)
Before continuing, look for a place to install the transceiver which:
•
Is far enough away from any device sensitive to magnetic/electromagnetic
fields (e.g. compass) in order to avoid interference during their use.
(14) Nuts (2 pieces)
(15) GPS receiver connecting cable (not shown)
(16) Operator Warning Label (not shown)
(17) Certificate of warranty and instruction manual (not shown)
•
•
Allows for accessibility to the front panel of REGATTA 2.
Provides easy connection to a power supply, for the antenna and for other
cables.
•
•
Has sufficient space close by for installation of the microphone support.
Allows for mounting of the antenna at least 3 feet from the transceiver.
ꢀ
Depending on the model, some parts may already be attached/connected to the device.
In any case, if any parts are missing, immediately contact your supplier.
ꢀ
The supplied universal mounting bracket allows for mounting of the transceiver high up
(with the bracket above the device) or on the bridge (with the bracket below the device)
with an angle range of 45°.
,
Warning! Installation and connections must be performed in part by qualified
persons.
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Align the transceiver on the bracket, ensuring the holes of the internal part of
the bracket line up with those on both sides of the transceiver (you can choose
the preferred notch in order to best adjust the angle of the transceiver’s front
panel for ease of viewing and use (150 of variation for each notch).
3.3 Mounting the transceiver
To mount the transceiver to your vessel (see following picture):
7. Attach the mounting knobs on the two sides of the bracket to soundly fix the
transceiver.
1. Choose an appropriate location, as explained in the paragraph above.
2. Position the mounting bracket on the surface upon which it will be fixed, use a
pencil to draw the position of the four holes where the screws will be inserted.
,
Keep the transceiver and microphone at a distance of at least 3 feet from all other
magnetic devices (e.g. compass) on your vessel.
,
Ensure that the surface intended for the transceiver mounting can be drilled into
without damaging other parts of the vessel and be careful to not drill right through
it.
3. Remove the bracket, drill four holes smaller in diameter than the screws, and
reposition the mounting bracket, aligning it with the four holes.
4. Screw in the mounting screws and ensure the bracket is fixed firmly, using the
screws, the grained washers, the flat washers and the nuts supplied.
,
If you are not able to reach the back part of the bracket surface to fix the nuts onto
the screws, use wood or sheet-metal screws to fix the bracket.
5. Tighten the screws with a screwdriver so that the bracket is firmly fixed to the
surface.
3.4 Adjustment of angle
To change the angle of inclination after installation:
1.
2.
Loosen the mounting knobs on the sides of the bracket.
Adjust the transceiver to a better angle, lining up the holes of the internal part
of the bracket with those on both sides of the transceiver.
3.
Tighten the knobs to fix the transceiver into place.
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
3.5 Installation of the antenna/electromagnetic exposure
For optimal radio settings and minimal user exposure to electromagnetic radio
frequency energy, ensure that:
•
•
The antenna is connected to the transceiver and is properly installed.
The antenna is situated away from people and is positioned at least three feet
from the transceiver and microphone.
•
The connector is a standard PL259 (male UHF).
3.6 Mounting of Microphone
To install the microphone mount, look first for a mounting point close to the
transceiver. The distance between the transceiver and the wall mount must be less
than the length of the microphone cable.
,
Do not pull excessively on the microphone cord.
This part is important to the correct operation of
the radio: over time, pulling may damage the cord
and impede the user from transmitting.
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Wire Colors of Accessory cable:
3.7 Connections
Refer to the following diagram:
GREEN: to GPS +
YELLOW: to GPS -
3.7.c Antenna
The antenna is an extremely important part of the device and noticeably influences
the settings of any telecommunications device. Contact your supplier regarding the
antenna and request advice about how to mount and best connect it to your
transceiver.
,
Warning! Ensure the antenna is in perfect working order. It may otherwise
seriously damage the radio! A periodical measurement of the stationary waves is
advised using a suitable SWR meter.
3.7.a Power Supply
The transceiver power supply must be 12V DC (see Technical Specifications,
Sec.12). The red cable must be connected to the positive pin, the black to the
negative pin.
,
,
Warning! A faulty connection may seriously damage the radio!
The power cable is equipped with a protection fuse. If the fuse shorts, look for its
reason before substituting the cable with a new one of the same type and value.
Never short-circuit it, as this may damage the radio.
3.7.b GPS device
If your REGATTA 2 transceiver is connected to a GPS receiver, you can obtain and
view NMEA information relative to the current position the vessel (latitude and
longitude) and the local time with respect to Greenwich Mean Time (GMT).
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
4.4
Selecting an operating channel
4.
BASIC OPERATION
4.4a With alphanumeric keypad
1. Ensure that you are in normal operating mode (radio mode), otherwise
press the “RAD” button several times or press the “C” button until the
display looks like FIG. A.
4.1
Turning REGATTA 2 on/off
To turn the transceiver on, rotate the ON/OFF/VOLUME knob clockwise until it clicks
on. You will hear a beep (acoustic signal) and the LCD display will come on: the
device is turned on to VHF mode.
2. Select the desired channel and confirm by pressing
the “E” button.
To turn the transceiver off, rotate the knob counter-clockwise until you hear a click:
the LCD display will turn off.
3. To select a channel with A or B suffix, an A or B will
appear next to a key. Press the key for the letter,
then press the “E” button.
Fig. A
ꢀ
If your transceiver is not connected to a GPS receiver, it is necessary to manually insert
your coordinates, otherwise an alarm will continue to sound. For further details, see
Par.6.1 & 6.3.
4. To select a weather channel for reception (USA or CAN only), press a
number key, then press and hold the WX+ key until the desired channel is
found. Press the “E” button to confirm.
ꢀ
ꢀ
ꢀ
If there is no confirmation within 2 seconds by pressing the “E” button, REGATTA 2 will
return to the previously used channel.
4.2
Volume regulation
Bring the ON/OFF/VOLUME knob first to medium volume. Once the transceiver
picks up a signal, adjust the volume to a comfortable level. If no signal is picked up,
use the squelch control as described in the following paragraph and regulate the
volume using background noise.
If a non-existant channel is inserted, for example CH99, the radio beeps 4 times after
pressing the “E”-button, REGATTA 2 returns to the previously used channel.
To switch between USA, Canada, and International channel lists, turn off the unit, and
while holding down the
button, turn the unit on. The display will indicate the band.
4.3
Squelch Regulation
Squelch is used to eliminate the annoying background noise you hear when no
signal is being picked up. If the squelch is adjusted correctly, there should be
silence in between calls as well as a reduction in battery consumption. To regulate
squelch:
4.4b Using the microphone buttons (UP or DOWN)
1.
Ensure that you are in normal operating mode (Radio mode); otherwise
follow the procedure described in par. 4.4.a.
2.
Press the UP or DOWN buttons on the microphone repeatedly to scroll
1.
Rotate the SQ knob completely counter-clockwise until you hear background
noise (if you don’t hear anything, turn up the volume) and bring up RX on the
LCD display.
through the marine channels until finding the desired channel.
ꢀ
ꢀ
Holding down one of the buttons will allow you to scroll quickly through the channels.
2.
If no signal is being received (only noise), slowly rotate the SQ knob
The marine band does not recognize some channel numbers. Refer to the frequency
table. The channels may have different receiving and transmitting frequencies (duplex
channels) or may have the same (simplex channels).
clockwise, stopping as soon as the noise and RX disappear.
ꢀ
If you regulate the squelch level too low (open), you may hear only background noise.
Correct setting of squelch is also important for reasons discussed further on.
ꢀ
Regulations require that some channels operate on low transmission power (see Chap.1)
For this reason, REGATTA 2 automatically switches to low power when these channels
are selected.
4.5
Transmission and reception
,
Transmitting without a perfectly functioning antenna may seriously damage the
transceiver.
Page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
4.8
Display lighting
The PTT (Push-To-Talk) button is located on the external microphone of your
REGATTA 2. To transmit:
If ambient lighting is insufficient for reading the display, the LCD display backlighting
can be adjusted. Hold pressed the button
has been completely turned off.
until a desired level is reached or until it
1.
2.
Ensure that no one else is speaking.
Hold down the PTT button on the microphone. TXwill appear on the
If the backlighting is activated, the display shows “LITE”.
Display.
The chosen level of backlighting remains stored, also in case of extinction
and successive turning on the radio.
3. Wait a second, then speak in a normal voice about 2 inches from the
microphone.
4. When you have finished, release the PTT button: TXwill disappear from the
display. Now REGATTA 2 is in receiving mode (silent and waiting for a
signal) where it will automatically receive any communication.
If you desire to switch off the backlighting immediately or if you like to reactivate the
previously inserted level, press the
button.
4.6
Selecting high and low transmission power
The transmission phase absorbs the most energy. To reduce the risk of wearing out
the battery, we recommend selecting low transmission power when transmitting over
short distances. Hold the H/L button down (on the radio): Lo(low power) appears
on the display. When transmitting or receiving over long distances or with weak
signals, press the H/L button again. Lowill be replaced with Hi(high power) on the
display.
ꢀ
ꢀ
When the transceiver is tuned to a channel limited to low output power, pressing the H/L
button has no effect.
In the standard mode, REGATTA 2 switches 25 W during high power output and 1 Watt
during low power output. Only on channels 15 and 17 the radio always reduces
automatically - according to the international agreements for maritime radio – to a value
under 1 Watt.
4.7
Instant recall of channel 16
Channel 16 is a security and distress channel. This channel is used to establish
initial contact with another station and for emergency communication. This channel
can be called up at any time by pressing button 16 on both the transceiver. To
return to normal operations, select another channel using the alphanumeric keypad
or the UP/DOWN buttons on the microphone. By pressing a second time the 16
button, the radio returns to the previously used channel before selecting channel 16.
,
Do not transmit on channel 16 unless absolutely necessary. Doing so may impede
emergency operations.
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
•
The scanning can be stopped by pressing the “C” button, or “16” button on the
microphone or by sending out a DISTRESS call. Your transceiver will stop on
the current channel (if you pressed the “C” button) or on channel 16 (if you
pressed 16 or PTT on the microphone).
5
SCANNING FUNCTIONS
ꢀ
Note: Scanning does not function correctly if the squelch is not regulated as described in
par.4.3.
5.1
Channel scanning
REGATTA 2 can automatically search for signals throughout the marine band by
scanning, or selecting the channels in rapid sequence. When a signal is detected,
the scanning pauses on that channel and remains blocked until the signal ends.
Before the scanning automatically starts again, REGATTA 2 waits for a few seconds
in case the user wishes, if necessary, to respond to a call even if in truth you will see
the channels being scanned.
5.2
Dual Watch and Triple Watch
The meaning of these terms are:
•
Dual Watch – allows the user to remain tuned to a channel of choice while
periodically performing an automatic verification of signals on channel 16.
The REGATTA 2 scanning happens with a minimum of 2
channels to a maximum of 56 channels on the INT band
(channel 70 is not selectable).
•
Triple Watch – as written above, including a third channel chosen by the user.
5.3
Activation of Dual Watch/Triple
•
In order to execute the scanning of the marine
channels, it is necessary to create a list of channels
for scanning. Operate in the following way:
To activate Dual or Triple watch:
Fig. B
•
Dual watch - Select a desired channel and press the D/W-button. The Display
will indicate “D/W” and you will see the two monitored channels.
1. Select a channel you desire to insert into the scanning list.
The Dual Watch function can be stopped in 5 different modes: by pressing the PTT-
or the “16” buttons on the microphone, “D/W”- or “C”-buttons or by sending out a
DSC-call.
2. Press and hold the “SCAN” (Fig. B); button for 2 seconds; the radio beeps
twice and on the display appears for a short time,
then the words “Scan Ena” (Fig. C) appear.
•
Triple watch – select one of the 2 channels you desire to monitor together with
channel 16. Hold pressed the function key corresponding to the indication T/W
until you hear two beeps. Now “User” appears on the display. (Fig. F). Move
now to the second channel you desire to monitor, press the function key
corresponding to T/W. Now you will see all three channels sliding on the
display with indication T/W. “Adv” appears too, that, similar to SCAN function,
has the aim to exclude momentarily the monitoring of
3. If you desire to cancel a channel from the scanning
Fig. C
list, repeat the procedure as described at point 2. In
that case the display is showing “Scan Inh”.
4. Once created your list, you can activate the
scanning by pressing the function key corresponding to the word “Scan”
(Fig. C).
the current channel.
•
If you want to eliminate (useful if there are distortions) or to exclude
momentarily (useful for undesired conversations) a channel during scanning,
operate as follows:
The Triple Watch function can be stopped by pressing the
“C” button, the PTT- or the 16-buttons or by sending out a
DSC call.
•
DEFINITIVE EXCLUSION OF A CHANNEL:
Fig.D
For both modes, the operation can be resumed with
the following diagram:
If your REGATTA 2 is operating on a busy
Fig. F
channel, press the “Inh” (Fig. D) . function key.
•
TEMPORARY REMOVAL OF A CHANNEL:
Press the function key corresponding to the written “Adv” to advance the
scanning and to temporarily remove this channel from the scanning list. At the
end of the complete scanning cycle, the channel previously jumped will be
monitored again.
Page 16
Download from Www.Somanuals.com. All Manuals Search And Download.
inserted into scan cycle, select the channel press and hold the “M/S”
function key until the display shows “M/S Del”. (Fig. I) .
4.
Once all channels are stored, the scanning can begin (SCAN MEMORY):
Press the function key corresponding to the written “M/S”. The channels will
be monitored and the display will show the script “M/S” – which indicates
the scanning of the stored channels, - “Adv” and “Del” in relation to the 2
function keys. Every time a signal/disturb is found on a channel, the
scanning stopps for a few seconds in order to give the user a chance to
respond to the call or to cancel the channel, if necessary.
ꢀ
Note: Scanning does not function correctly if the squelch is not regulated as described in
par.4.3.
5.4a Reception/Transmission during SCAN MEMORY
ꢀ
ꢀ
Similar to scanning of marine channels, Dual Watch and Triple watch stop when a signal
is found and remain blocked for a few seconds after the signal disappears, in order to
give the user a chance to respond to a call, if necessary.
•
•
Reception: If REGATTA 2 finds a signal the scanning interrupts. The display
indicates “RX” instead of “M/S” and the communication will be received through
the loudspeaker.
Dual/Triple Watch cannot function correctly if the squelch is not correctly regulated, as
described in par .4.3
Transmission: It is possible to transmit at any time, also when the scanning is
active. In that case REGATTA 2 will always transmit on channel 16; if instead
the transmission is done after a signal has been found, the device will transmit
on the previously busy channel. After the transmission the scanning comes
interrupted.
Fig. G
Memory channels (MEM mode)
5.4b To delete/To jump a pre-selected channel in memory
If during the scanning a signal is received on an undesired or disturbed channel, it is
possible to temporarily cancel the channel or to skip the channel momentarily.
In order to execute these functions, the radio must be syntonized on a channel (firm
scanning). Through the two function keys corresponding to “Adv” and “Del” you will
have the possibility to jump the busy channel respective to cancel it from the pre-
selected list of channels.
5.4
1.
Memory scanning (SCAN MEMORY)
Similar to the scan function, memory scan will
cycle sequentially through the channels, but
only those, which have been pre-selected (at
least 3).
Fig. H
There are 4 modes to stop the scanning of channels in memory:
2.
3.
Press the “M/S” function key (Fig. G). The radio emits 2 beeps and “M/S
Sel” appears on the display for about 2 seconds
(Fig. H).
1. By pressing the PTT-button.
Select another channel and repeat the procedure
2. By pressing the 16 button on the microphone or on the front panel
3. By pressing the C-button.
Fig. I
mentioned above.
In order to eliminate a channel erroneously
4. By sending out a DSC-Call.
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
7
DIGITAL SELECTIVE CALLING (DSC)
6
USE WITH GPS
7.1
Introduction
Digital Selective Calling is a semiautomatic method for controlling VHF, MF and HF
radio calls. It was also designed as part of the global marine security and
emergency response system (GMDSS). It is likely that DSC will eventually replace
audio calls on emergency frequencies and will be used to send urgent and routine
radio-transmitted maritime security information. This new service will allow crafts to
send/receive calls of an emergency, urgent, security, or routine nature to/from
vessels equipped with a DSC transceiver.
6.1
Function
If connected to a GPS receiver, the transceiver will display the vessel position
(latitude and longitude), as well as time data. If information regarding position data
are not received, in the normal radio mode, time data does not appear and a minute-
long warning tone will sound (can be deactivated by pressing any button). This tone
will sound every 4 hours, reminding the user that position data needs to be inserted.
The user may also insert the coordinates manually as described in par. 9.6.
,
To avoid accidentally sending a distress call or a call sent incorrectly, contact your
vendor or local authorities for updates on DSC operating and emergency
procedures.
6.2
GPS information on the display
,
In European inland waterways DSC-function is not allowed.
7.2
Mobile Marine Identification Service (MMSI)
ꢀ
Important! To send/receive DSC calls, the user must program his personal MMSI code
into the transceiver. This is a nine-digit number used by marine transceivers equipped for
DSC digital selective calling. This number is used much like a telephone number for
contacting other, specific vessels. For further details on programming your MMSI, see
par. 9.10.
Refer to the following illustrations:
1.
Position indicator
Displays GPS or manually inserted co-ordinates.
7.3
Navigating the DSC menu
2.
Time indicator
REGATTA 2 offers many DSC functions. For this reason it was created a specific
menu of settings and activations accessible via the function keys as follows:
1. Access the “CALL”-Menu by pressing the related function key.
Shows data supplied by the GPS or the transceiver’s clock.
6.3
Customized setup
Some GPS receivers may require a change in the manner the radio processes the
GPS data. Pressing GPS selection diplays CHECKSUM ON/OFF selection.
2. Press the function key corresponding to the word “Type” to select
the type of desired call.
ꢀ
Once inside a sub-menu, you can return at any time to the main menu by pressing the C-
button and terminating the current operation.
If no GPS receiver is connected, using WARN BEEP ON/OFF allows the user to
defeat the audible warning that new position data is required. Press C button to
return to menu. Display On/Off button controls the presence of the automatic display
announcing that the position data is over 4 hours old.
7.4
Individual call (Routine To)
CHECKSUM ON
The user can carry out an individual call to a specific DSC station (a vessel or a
costal station). To carry out calls, you have to enter the MMSI code manually or
recall it from the pre-programmed MMSI directory.
programming the MMSI directory, see par. 9.5.
CTEST
WARN BEEP ON
For further details on
DISPLAY ON
Page 18
Download from Www.Somanuals.com. All Manuals Search And Download.
7.4
Sending an individual call
In this case the answer is reached from ship 100000000 and the possible
communication channel will be CH06.
You can carry out an individual call using the following procedure:
To confirm the reception of the received message, REGATTA 2 will emit an acoustic
message that can be interrupted by pressing the function key corresponding to ”OK” or
“STOP”.
5.
6.
Press briefly the function key corresponding to
CALL. On the display appears:
Pressing OK beyond interrupting the acoustic signalling, REGATTA 2 is set to the
chosen communication channel (in our example 06).
The outlined line below under "Routine To” appears
if no owner name was inserted in the column “Dir”,
otherwise a similar situation may appear:
If no function key comes pressed at that time (1 minute) the acoustic message will
extinguish automatically.
Fig. J
−
If the call is not acknowledged, the display will indicate
(M) ; by pressing the function key corresponding to
“Stop” the radio will return to the normal radio mode.
Fig. M
ꢀ
Once inside a sub-menu, you can return at any time to the
main individual CALL-menu (Routine to) by pressing the C-
button and terminating the current operation.
Fig. K
7.5
Group calling (Group Call)
This function allows the user to call a specific group of stations which have the same
MMSI group code memorized in their transceivers and which signals the channel the
user wishes to speak on. Therefore you can only carry out the group call when you
have programmed the addresses in a directory as described in par. 9.5
7.
8.
Press the function key “Ch 06” to access the sub-menu.
Press several times the function key “Chan” in order to select one of the 23
available channels (simplex channels) and confirm by pressing the “E” button.
Sending a group call
9.
Like mentioned above, it is possible, to insert manually the address you want
to call (using the alphanumerical keypad), or to select one of the addresses
previously stored (maximum 16) by pressing several times the function key
related to the indication “DIR”.
1. You can carry out a group call through following
procedure:
2. 1. Press briefly the function key corresponding to
“Call”. On the display appears:
Fig. N
10. Then, after you have selected the communication channel and the address,
the call can be carried out by pressing the function key corresponding to
“Send” and confirmed by pressing the “E” button.
3. Press three times the function key corresponding to
the written “Type” in order to to visualize on the display the following situation:
11. After the call execution the radio operates as follows:
−
If you have carried out a call to a ship, after the call,
you will get an answer, the radio will move to the
channel previously selected under step 3-4.
Fig. O
4. The outlined line below under “Group Call” appears
when no address has been programmed in the
column “Dir”.
Fig. L
12. At this point:
If the call comes confirmed from the other part, the
display shows the message:
−
5. Press the function key “Ch 06” to access the sub-menu.
6. Press several times the function key “Chan” to select one of the 23 available
channels (simplex channels) and confirm by pressing the “E” button.
Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Like mentioned above, it is possible, to insert manually the address of who is
desired to call (using the alphanumerical keypad), or to select one of the
addresses previously stored (maximum 16) by pressing several times the
function key related to “DIR”.
6. At this point:
−
−
If you wish to confirm the call, press the E-button to continue.
If you don’t want to carry out the call (because of errors), press the 16 button or
the “C” button to leave the menu.
8. Then, after you have selected the communication channel and the owner
address, the call can be carried out by pressing the function key corresponding
to the script “Send” and confirmed by pressing the “E” button.
7. The call will be carried out on channel 70. The radio then will return to VHF
mode on channel 16.
9. At this point you can communicate with the stations on the pre-selected
channel that have given an answer to you.
ꢀ
During this procedure you are able to return to the main CALL-menu by pressing the “C”
button.
ꢀ
Once inside a sub-menu, you can return at any time to the main CALL-menu by pressing
the “C” button.
7.7. DSC DISTRESS call
7.6
URGENCY)
General call to all ships (ALL SHIP SAFETY – ALL SHIP
7.7.a Sending a DISTRESS call
ꢀ
IMPORTANT! You can only send a DSC call if you have been assigned an individual
MMSI code and this code has been programmed into the transceiver (otherwise the
following commands will be deactivated). For this operation, see par. 9.10
Sending a call to all ships
,
Sending a distress call without founded reason is a criminal offence. Never use
this function unless you find yourself in a situation that merits requiring help.
,
Sending a distress call without founded reason is a criminal offence. Never use
this function unless you find yourself in a situation that merits asking for help.
1. You can carry out a call to all
ships through following
procedure:
Fig. S
2. Press the function key
related to the written “DSC”.
Fig. Q
You can carry out the distress call through the following procedure:
Fig. P
3. Press the function key related to “Call”.
1. Open the DISTRESS cover by pushing it to the right and hold it open.
2. Press momentarily the DISTRESS-button below. The display shows: (Fig. S)
4. Press one time the function key “Type” in order to select the type of call
SAFETY(Fig. P), otherwise press two times to select the type URGENCY
(Fig. Q).
3. Press the function key corresponding to “Undefined” in order to select the
nature of the call (the pre-selection is UNDEFINED):
5. Select the type of desired call and press the function key corresponding to
“Send”. Channel 16 is automatically selected and the display requests
confirmation before sending the call with the message (Fig. R)
A. UNDEFINED
B. ABANDONING
C. PIRACY
D. M.O.B. (man over board)
E. FIRE
Fig. R
F. FLOODING
G. COLLISION
Page 20
Download from Www.Somanuals.com. All Manuals Search And Download.
H. GROUNDING
I. LISTING
L. SINKING
M. ADRIFT
4. To send out the distress call hold down the DISTRESS-button for 5 seconds. An
acoustic alert will emit and the distress call will be carried out on channel 70
even when the channel is in use.
5. After the distress call, the transceiver will simultaneously check channel 70 and
channel 16 on a receipt of DSC confirmation and meanwhile appears following:
6.
At this point:
−
If the distress call is received and confirmed by
another DSC radio station, the acoustic alarm will
stop sounding and the display will return to
normal use in VHF mode on channel 16, sending
on high transmission power.
Fig. T
−
If no confirmation is received, the device will re-send the distress call at
intermissions of 3.5 – 4.5 minutes (even with channel 70 in use), until a
confirmation is received or until the user manually cancels the call through the C-
button.
,
ꢀ
By pressing button 16, the transceiver will return to normal VHF operation, but the
call will not be cancelled and the person who responded to the call may not have
called off rescue operations.
If, at step 4, the user stops pressing the DISTRESS button before 5 seconds have
elapsed, the distress call will not be sent. To exit and return to VHF mode, press button
16.
ꢀ
ꢀ
The acoustic alarm will only stop definitively once the transceiver has received
confirmation from the receiver of the call.
It is possible to arrest the acoustic alarm by pressing the button “C” or “16”.
Page 21
Download from Www.Somanuals.com. All Manuals Search And Download.
8.2
General call to all ships
8
Receiving a DSC call
When the transceiver receives a general call related to all vessels, it automatically
moves to the communication channel and emits an acoustic emergency alarm. The
pressure of the function key “STOP” will deactivate the alarm.
When the user receives a DSC call, the transceiver will automatically respond
according to the type of call.
Information shown on the LCD display will vary according to the type of call. Refer
to the diagram below for several examples:
Individual call
DISTRESS CALL
GENERAL CALL
TO ALL VESSELS
INDIVIDUAL CALL
When the transceiver receives an individual call, it automatically move to the channel
indicated by the DSC signal and emits a tone to alert the user of an incoming call.
The pressure to the function key “STOP” will deactivate the alarm.
The MMSI owner code contained in the signal appears on the display. If the MMSI
owner code has been programmed previously with name in the directory, the name
of the caller appears too.
Every time REGATTA 2 receives a call (distress, individual or general) an entry will
be stored in the list of registered calls “LOG”.
8.1
Receiving a distress call
When the transceiver receives a distress call, an acoustic alarm will sound. The
pressure to the function key “STOP” will deactivate the alarm.
When the signal also includes position and time data, this information will appear on
the display. If no position and time data are included in the signal, the display will
indicate 99°99 999°99 88:88.
Page 22
Download from Www.Somanuals.com. All Manuals Search And Download.
9
CUSTOMIZATION
9.5
“Dir” (Entries in the directory)
9.1
Menu settings
You can insert into the directory the MMSI codes from frequently called stations, by
giving them a name (e.g. vessel or owner). Then you can search and use them
more comfortably. When receiving a call, MMSI owner name and MMSI code will be
displayed.
REGATTA 2 can carry out a series of settings in order to personalize the transceiver
to your requirements and to insert the necessary data to its operation.
1. Press the function key “Menu”.
2. Press the function key “More”.
3. Press the function key “Dir”.
9.2
Navigation in the menu of settings
To access the menu of setting use the functions keys.
All programmed settings are stored in non-volatile memory.
4. At this point you enter to the directory pages. If no
MMSI owner address was stored, the display will show
“Empty”, throughout it has been stored one or two MMSI
owner addresses, the type of indication will appear as
9.3
List of settings
Following find the possible settings:
follows:
Fig. U
Menu Items
Log
Description
Call directory of stored DSC calls type individual or
distress calls.
Directory of MMSI owner names, MMSI codes and
their details.
Manual programming of co-ordinates and the UTC
time setting (in the absence of GPS).
Display contrast adjustment.
Par.
9.4
5. By pressing the function key “Add” you will have the possibility to add further
MMSI addresses. Pressing the function key “VIEW” you will have the possibility
to modify/cancel the address shown on the display.
Dir
9.5
9.6
Posn
LCD
9.7
9.8
9.9
9.5.a Addition of addresses
Fig. V
Beep
ZONE
MMSI
Adjustment of keypad beep
9.a.1 Press the function key “Add”.
Local and UTC time deviation settings.
Entry of your individual MMSI code and you MMSI
group code.
9.a.2 With the alphanumerical keypad (the
keys are associated with letters like on a
cellular phone) you are able to write the name you want to associate with the
MMSI code (f.e. TOM), then press the E-button to confirm.
9.10
9.a.3 After the pressure to the E-button, on the display appears the cursor in
correspondence to “MMSI”
9.4
“Log” (list of registered calls)
With this menu you can consult a directory of the latest registered calls, in
analogous way to the registrers of calls on a cellular phone.
Write the identification code using the alphanumerical keypad (obligatorily
9 digits)
- Press the function key “DSC”.
9.a.4 Press the E-button in order to confirm.
9.5.b To modify/cancel addresses
1 Press the function key “View”.
- Press the buttons “DSC” and “Log”. It will be shown the latest registered message.
- By pressing the function key corresponding to “Back” all the other registered
messages will be shown.
2 Select with the function keys “Next “ or “Back” the address you desire to
modify/cancel.
- Using the function keys corresponding to the symbol “▼” you will get some more
information: co-ordinates and time.
3 Press the function key “Edit”.
Page 23
Download from Www.Somanuals.com. All Manuals Search And Download.
4 If you desire to change the name or the code, press one of the 2 function
keys associated to the name or the MMSI code “►”.
9.7
“LCD” (display contrast)
The user can adjust the display contract to optimise visibility according to ambient
conditions.
1. Press the function key “DSC”.
2. Press the function key “Menu”.
3. Press the function key “LCD”.
Fig. W
4. Using the function keys corresponding to “▼” ; “▲” you can increase the contrast
of the display.
9.b.5 If it is desired to eliminate completely the directory, press the function
key “Del” and confirm by pressing subsequently the function key “Yes”.If
you desire to cancel the operation, press the function key “NO”.
5. Confirm by using one of the following buttons: C , 16, function key DSC, or the
PTT.
ꢀ
This setting remains stored on the Eeprom, therefore REGATTA 2 will maintain the same
settings when the radio is turned on again.
ꢀ
It is possible to memorize max. 16 addresses. If the directory is filled up, on the display
will appear the indication “Full” and it will not be possible to add further addresses. In this
case it is necessary to cancel some.
9.8
“Beep” (Enable/disable keypad beep)
In order to activate or to inhibit the beep to the pressure of the keys operate as
follows:
9.6
“Posn” (Setting of position co-ordinates and adjustment
1. Press the function key “DSC”.
2. Press the function key “Menu”.
3. Press the function key “More”.
4. Press the function key “ More”.
of UTC time)
1. Press the function key “DSC”.
2. Press the key “Menu”.
3. Press the key “Posn”.
5. Pressing the function key “Beep” activates or disables the acoustic message to
the pressure of the keys.
4. To insert the coordinates, press the function key “Posn” and through the
alphanumeric keypad, set up the coordinates.
ꢀ
This setting remains stored on the Eeprom, therefore REGATTA 2 will maintain the same
settings when the radio is turned on again.
5. Confirm by pressing the E-button. If “non-existent” coordinates have
been inserted, REGATTA 2 will emit a double error beep rendering
necessary the re-insertion.
6. In order to set the time, press the function key corresponding to “UTC”,
and confirm through the E-button the executed operation. An eventual
error message will indicate the wrong entry of time data.
ꢀ
The insertion of time coordinates is required to carry out DSC calls. If REGATTA 2 is
connected to a compatible GPS receiver (GPS 200) the setting of these data is not
compulsory. Sending DSC without setting position and time works but message will lack
the position and time data.
Page 24
Download from Www.Somanuals.com. All Manuals Search And Download.
9.9
“ZONE” (Adjustment of UTC time deviation)
The user can program the time deviation with respect to the UTC time so the
transceiver’s display will show the time for the current time zone.
5. To insert the personal MMSI code press the function key to the right under the
arrow corresponding to the script “DSC”. The display will show the message
“Enter MMSI".
6. Insert the 9 digits, for example 900000000 and press the E-button in order to
confirm, now on the display appears:
1. Press the function key “DSC”.
2. Press the function key “Menu”.
3. Press the function key “More”.
4. Press the function key “ More”.
5. Press the function key “Zone”.
7. To program the MMSI group code, press the function key corresponding to “►”
situated right below.
8. On the display will appear the message “Enter Group MMSI”, now program 8
numbers (the first fixed number is 0 (zero)) and confirm by pressing the E-
button.
6. The display will show
Fig. X
Fig. Z
7. Pressing the function keys “+” or “–“ will set the desired deviation.
8. Acting with the function key ◄ will activate or eliminate the visualization of the
time data on the display.
9. Confirm by pressing one of the following buttons: C , 16, function key DSC, or
ꢀ
ꢀ
It is possible to change the MMSI group code whenever you want, while the personal
MMSI code can be inserted only one time; for this reason, we recommend to pay
attention.
PTT.
ꢀ
This setting remains stored on the Eeprom, therefore REGATTA 2 will maintain the same
settings when the radio is turned on again.
If you have accidentally inserted an incorrect code, you will have to return the device to
your approved vendor for a complete reset.
9.10 MMSI (Setting of personal MMSI code and MMSI group
code)
10 MAINTENANCE
This function allows the user to insert their personal MMSI identification code
assigned by an appropriate authority.
10.1 Maintenance and warnings
REGATTA 2 is a marine VHF transceiver that conforms to IP54 standard, making
the transceiver very reliable when used correctly.
,
Be careful to insert the correct personal MMSI code. Once the code has been
saved, it cannot be modified.
The device was designed so as to avoid requiring maintenance. To keep your
transceiver in optimal operating conditions:
1. Press the function key “DSC”.
2. Press the function key “Menu”.
3. Press the function key “More”.
,
,
Never open the device (transceiver or microphone) as this may compromise the
water resistant seal.
4. Press the function key “MMSI”. The display
will show:
If the device becomes dirty or dusty, do not use alcohol, solvents or abrasives to
clean it. Use only a soft cloth, slightly dampened with water. For more persistent
cases, use a mild detergent.
Fig. Y
Page 25
Download from Www.Somanuals.com. All Manuals Search And Download.
11 Troubleshooting
Problem
Possible causes
Power supply is not correctly
connected
The protection fuse has shorted
(located on the power cable)
Solution
Verify that power supply is
properly connected
Verify the cause of the
problem and substitute the
fuse
Refer.
3.7.a
Device doesn’t turn
on
-
Antenna is not correctly connected Verify that antenna is
properly connected
3.7.c
Device turns on, but
doesn’t receive
signals
Volume level is too low
Squelch level is too high
Adjust volume level
Adjust squelch level
4.2
4.3
Unable to contact
another party
Incorrect marine channel selected Verify channel and, if
necessary, change channel
4.4
Other party has
difficulty in hearing transmission power (LO) was
Distance is too far and low
Select high transmission
power (HI)
4.6
4.3
4.3
you
accidentally selected
Squelch level is too high
Signal is too weak (other party is
too far away and/or antenna is
blocked by obstacles)
Adjust squelch level
Try to completely open the
squelch and/or move closer
to the other party
Other users are using the same
radio channel
Verify radio traffic on desired
channel and, if necessary,
change channel
Move other interference
devices further from
REGATTA 2
Reception is broken
and/or disturbed
4.4
-
Other interference devices
(televisions, computers,
transceivers, etc.) too close to
REGATTA 2
Impossible to
Some channels operate only on
Tune to another channel
Program the codes
transmit or use high low power or are only for reception
transmission power
DSC, MMSI or ATIS Individual MMIS and/or ATIS
functions unusable codes have not been programmed
Vessel battery runs Excessive use of transmission
down sooner than
4.4
4.10
4.6
Try to reduce transmission
times and/or use low
transmission power
expected
Scanning and/or
Dual/Triple Watch
malfunctioning
Squelch has not been correctly
adjusted
Adjust squelch level
4.3
Page 26
Download from Www.Somanuals.com. All Manuals Search And Download.
12 TECHNICAL SPECIFICATIONS:
Channels ..................................................All 48USA, 55 Canadian & 57 international marine channels,
Frequency generation......................................................................................................PLL synthesizer
Frequency range..................................................................................TX from 156.025 to 157.425 MHz
............................................................................................................. RX from 156.050 to 162.550 MHz
Antenna Impedance......................................................................................................................50 Ohm
Power supply.................................................................................................................................12 VDC
Operating temperature..............................................................................................from -20°C to +55°C
Size (HxLxW) .................................................................................................................70×160×170 mm
Weight (device only) ...................................................................................................................1.305 Kg
12.1 Transmitter
Output power...............................................................................................High (HI): 25W/Low (LO):1W
Modulation Type................................................................................................................................... FM
Microphone ...................................................................................................................... condenser type
Hum and noise attenuation............................................................................................................... 34dB
Audio distortion .................................................................................................................................... 5%
Harmonics reduction....................................................................................................HI: 80dB/LO:60dB
12.2 Receiver
Sensitivity @ 20 dB Sinad .............................................................................................................<0.5µV
S/N ratio (20dB) ...............................................................................................................................0,8µV
Squelch sensitivity .......................................................................................... threshold -12dBµV (EMF)
Adjacent channel rejection................................................................................................................ 70dB
Audio output power........................................................................................................... >2W su 8 Ohm
Audio distortion .................................................................................................................................. 10%
ꢀ
Note: these values are average. Actual values may be subject to variation.
Page 27
Download from Www.Somanuals.com. All Manuals Search And Download.
13 Frequency Table
Channel Number
Frequency MHz
.
INT CAN US
TX
157.100 161.700
22A 22A 157.100 157.100
RX
Mode
Note
INT CAN US
TX
RX
Mode
Note
22
D
S
D
S
D
D
D
D
D
D
D
S
D
S
D
S
D
S
D
S
D
S
S
S
S
S
S
S
S
S
S
S
S
01 01
156.050 160.650
01A 156.050 156.050
156.100 160.700
156.150 160.750
156.200 160.800
156.200 156.200
156.250 160.850
D
S
D
D
D
S
D
S
S
D
S
S
S
S
S
S
S
S
S
R
S
S
D
S
D
S
D
S
D
S
R
23 23
157.150 161.750
23A 157.150 157.150
02 02
03 03
04
24 24 24 157.200 161.800
25 25 25 157.250 161.850
26 26 26 157.300 161.900
27 27 27 157.350 161.950
28 28 28 157.400 162.000
04A
05
05A 05A 156.250 156.250
60 60
61
156.025 160.625
156.075 160.675
156.075 156.075
156.125 160.725
156.125 156.125
156.175 160.775
63A 156.175 156.175
156.225 160.825
156.225 156.225
156.275 160.875
06 06 06 156.300 156.300
07
156.350 160.950
61A
62
07A 07A 156.350 156.350
08 08 08 156.400 156.400
09 09 09 156.450 156.450
10 10 10 156.500 156.500
11 11 11 156.550 156.550
12 12 12 156.600 156.600
13 13 13 156.650 156.650
14 14 14 156.700 156.700
62A
63
64 64
64A
65
65A 65A 156.275 156.275
156.325 160.925
15 15
156.750 156.750
156.750
*
*
66
15
-
66A* 66A 156.325 156.325
16 16 16 156.800 156.800
17 17 17 156.850 156.850
67 67 67 156.375 156.375
68 68 68 156.425 156.425
69 69 69 156.475 156.475
70 70 70 156.525 156.525
71 71 71 156.575 156.575
72 72 72 156.625 156.625
73 73 73 156.675 156.675
74 74 74 156.725 156.725
18
156.900 161.500
18A 18A 156.900 156.900
156.950 161.550
**
19
19A 19A 156.950 156.950
20 20* 20 157.000 161.600
20A 157.000 157.000
21
157.050 161.650
75
76
156.775 156.775
156.825 156.825
*
*
21A 21A 157.050 157.050
21B
-
161.650
77 77* 77* 156.875 156.875
Page 28
Download from Www.Somanuals.com. All Manuals Search And Download.
INT CAN US
TX
RX
Mode
Note
78
156.925 161.525
D
S
D
S
D
S
D
S
D
S
D
S
D
78A 78A 156.925 156.925
156.975 161.575
79
80
81
82
79A 79A 156.975 156.975
157.025 161.625
(Nautico1) WEATHER (WX) RECEIVER FREQUENCY CHART (MHz)
80A 80A 157.025 157.025
157.075 161.675
CH.#
W1
W2
W3
W4
W5
CH. Freq.
162.550
162.400
162.475
162.425
162.450
CH. #
W6
CH. Freq.
162.500
162.525
161.650
161.775
163.275
81A 81A 157.075 157.075
157.125 161.725
W7
82A 82A 157.125 157.125
W8
83 83
157.175 161.775
83A 83A 157.175 157.175
W9
84 84 84 157.225 161.825
W10
85 85 85 157.275 161.875
D
D
Channels 8,9 and 10 are designated Canadian Marine Frequencies
86 86 86 157.325 161.925
87
88
157.375 161.975
157.375 157.375
D
S
D
S
87
88
157.425 162.025
88A 157.425 157.425
S= Simplex
D= Duplex
1120 Clay Street
North Kansas City, MO 64116
*= obligatory low transmission power of 1 Watt
**= classified to DSC communications
Page 29
Download from Www.Somanuals.com. All Manuals Search And Download.
Printed in Thailand
P/N: RG500220
Page 30
Download from Www.Somanuals.com. All Manuals Search And Download.
|