INSTALLATION INSTRUCTIONS FOR PART 99-2008
APPLICATIONS
Cadillac DTS 2006-2010
Cadillac SRX 2007-2009
99-2008
KIT FEATURES
• DIN Radio Provisiion with Pocket
• ISO Mount Radio Provisiion with Pocket
• Double DIN Radio Provisiion
• Stacked ISO Mount Units Provisiion
KIT COMPONENTS
A) Radio Housing • B) ISO Trim Plate • C) ISO Brackets • D) Double DIN Trim Plate
• E) Double DIN Brackets • F) Pocket
D
B
C
WIRING AND ANTENNA CONNECTIONS
(Sold Separately)
• GMOS-LAN-01 - GM LAN Interface
2006-up
• GMOS-LAN-02 - GM LAN Amplified-
Interface 2006-up
A
• GMOS-LAN-05 - GM Digital LAN Amp
Interface With Onstar 2007-up
• Antenna Adapter:
E
40-CR10 - Chrysler/GM Antenna
Adapter 2002-up
F
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel Removal Tool
• Phillips Screwdriver • Socket Set
1-800-221-0932
© COPYRIGHT 2004-2009 METRA ELECTRONICS CORPORATION
Download from Www.Somanuals.com. All Manuals Search And Download.
99-2008 DASH DISASSEMBLY
Cadillac DTS 2006-2010
A
1
2
Disconnect the negative battery ter-
minal to prevent an accidental short
circuit.
Unclip and remove the trim panel
around the radio, climate controls and
ac vents and above glove box.
(Figure A)
3
4
5
Remove (4) 9/32” screws securing
the a/c vent panel. Unplug and
remove the panel. (Figure B)
B
Remove (4) 9/32” screws securing the
climate controls. Unplug and remove
the climate controls. (Figure C)
Remove (4) 9/32” screws securing
the radio. Unplug and remove the
radio. (Figure D)
Continue to kit assembly.
C
D
1
Download from Www.Somanuals.com. All Manuals Search And Download.
99-2008 DASH DISASSEMBLY
Cadillac SRX 2007-2009
A
1
2
3
Disconnect the negative battery ter-
minal to prevent an accidental short
circuit.
Unclip and remove trim piece
between shifter and cup holders.
(Figure A
Unclip and remove the trim panel
around the radio, climate controls,
ac vents and front half of center
console. (Figure B)
B
C
D
4
5
Remove (3) 9/32” screws securing
the a/c vent panel and remove the
panel. (Figure C)
Remove (4) 9/32” screws securing
the climate controls. Unplug and
remove the climate controls.
(Figure D)
6
Remove (4) 9/32” screws securing
the radio. Unplug and remove the
radio. Figure E)
Continue to kit assembly.
E
2
Download from Www.Somanuals.com. All Manuals Search And Download.
99-2008 KIT ASSEMBLY
DIN RADIO PROVISION WITH POCKET
*Note: Refer also to the instructions included with the aftermarket radio.
A
1
2
3
Slide the DIN cage into the Radio
Housing and secure by bending the
metal locking tabs outward. (Figure A)
Slide the aftermarket radio into the
cage until it snaps into place.
(Figure B)
Snap the pocket into the housing.
(Figure C)
B
Continue to final assembly.
C
3
Download from Www.Somanuals.com. All Manuals Search And Download.
99-2008 KIT ASSEMBLY
ISO MOUNT RADIO PROVISION WITH POCKET
*Note: Refer also to the instructions included with the aftermarket radio.
A
1
Mount the ISO Brackets to the radio
using the screws supplied with the
radio. (Figure A)
2
3
4
Slide the radio into the radio housing
until it snaps into place. (Figure B)
Snap the trim plate onto the front of
the radio housing. (Figure B)
Snap the pocket into the housing.
(Figure C)
B
Continue to final assembly.
C
4
Download from Www.Somanuals.com. All Manuals Search And Download.
99-2008 KIT ASSEMBLY
DOUBLE DIN RADIO PROVISION
*Note: Refer also to the instructions included with the aftermarket radio.
A
1
2
Cut and remove the center bar from
the radio housing. (Figure A)
Snap the Double DIN brackets to the
inside edge of the radio housing.
(Figure B)
3
4
Slide the Double DIN radio or stacked
ISO mount units into the bracket/radio
housing assembly then secure to the
assembly using the screws supplied
with the radio or ISO mount units.
B
(Figure C)
Snap the Double DIN Trim plate onto
the front of the Radio Housing.
(Figure C)
Continue to final assembly.
C
5
Download from Www.Somanuals.com. All Manuals Search And Download.
99-2008 FINAL ASSEMBLY
FINAL ASSEMBLY
A
B
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
C
D
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown. (Isolate and individ-
ually tape off the ends of any unused wires to prevent electrical short circuit.)
1
2
3
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the
head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc. . . . . . . . . . Red
Right Front (+) . . . . . . . . . . . . Gray
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Black*
Power Antenna. . . . . . . . . . . . Blue
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
REV. 04/21/10 © COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION INST99-2008
6
Download from Www.Somanuals.com. All Manuals Search And Download.
|