INSTALLATION INSTRUCTIONS FOR PART 99-8205
APPLICATIONS
Toyota Matrix 2003-2008
Pontiac Vibe 2003-2008
99-8205
KIT FEATURES
• DIN head unit provision
• ISO DIN head unit provision
• DDIN head unit provision
- Excluding 2005-2008 Matrix
• Stacked ISO DIN head unit provision
- Excluding 2005-2008 Matrix
KIT COMPONENTS
A) DDIN Faceplate (excluding 2005-2008 matrix) • B) ISO DIN Faceplate (excluding 2005-2008 matrix)
• C) ISO DIN Faceplate 2005-2008 Matrix D) Pocket • E) Mounting Brackets • F) ISO Trim Plate • G) ISO Brackets
• H) ISO Spacers • I) Rear Support • J) (4) #6x1/4” Phillip Screws • K) (4) #8x3/8” Phillip Screws
B
A
C
H
E
D
G
F
J
I
K
TOOLS REQUIRED:
Cutting Tool • Phillips Screwdriver • Socket Wrench
1-800-221-0932
© COPYRIGHT 2004-08 METRA ELECTRONICS CORPORATION
Download from Www.Somanuals.com. All Manuals Search And Download.
DASH DISASSEMBLY
99-8205
TOYOTA MATRIX 2003-2008
PONTIAC VIBE 2003-2008
A
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
1
2
3
Unclip the bottom edge of the radio
trim panel then lift up and out to
remove. (Figure A)
Remove (4) 10 MM bolts securing
the factory radio. (Figure B)
B
1
Download from Www.Somanuals.com. All Manuals Search And Download.
KIT ASSEMBLY
99-8205
DIN HEAD UNIT PROVISION
A
Choose the correct faceplate for your
1
2
application. The 2005-2008 Matrix
faceplate is smaller than the other
supplied faceplate.
#8x3/8”Screw
Attach the pocket to the back of the
ISO/DIN Faceplate (by holding the
faceplate upside down and inserting
the right edge of the pocket into
place then pushing the rest of the
pocket onto the lip) and mount with
(2) #8X3/8” Phillips screws.
#8x3/8”Screw
B
(Figure A)
NOTE: For the 2005-2008 Matrix,
break away the shaded clips along
the scored lines. (Figure B)
Secure the mounting brackets to the
pocket with (4) #6X1/4” Phillips
screws. (Figure C)
3
C
#6x1/4” Screws
Two
#8x3/8” Screws
#6x1/4” Screws
2
Download from Www.Somanuals.com. All Manuals Search And Download.
KIT ASSEMBLY
99-8205
DIN HEAD UNIT PROVISION
D
Mount the rear support to the back
of the pocket with (2) #8X3/8”
Phillips screws. (Figure D)
4
5
6
Two
#8x3/8” Screws
Slide the DIN cage into the Radio
Housing and secure by bending the
metal locking tabs down. (Figure E)
Slide the aftermarket head unit into
the cage and secure. (Figure F)
E
F
3
Download from Www.Somanuals.com. All Manuals Search And Download.
99-8205
KIT ASSEMBLY
ISO DIN HEAD UNIT PROVISION
A
Choose the correct faceplate for your
application. The 2005-2008 Matrix
faceplate is smaller than the other
supplied faceplate.
#8x3/8”Screw
1
2
#8x3/8”Screw
Attach the the pocket to the back of the
ISO/DIN Faceplate (by holding the face-
plate upside down and inserting the right
edge of the pocket into place then push-
ing the rest of the pocket onto the lip)
and mount with (2) #8X3/8” Phillips
screws. (Figure A)
B
NOTE: For the 2005-2008 Matrix,
break away the shaded clips along
the scored lines. (Figure B)
Secure the mounting brackets to the
pocket with (4) #6X1/4” Phillips
screws. (Figure C)
3
C
#6x1/4” Screws
Two
#8x3/8” Screws
#6x1/4” Screws
4
Download from Www.Somanuals.com. All Manuals Search And Download.
99-8205
KIT ASSEMBLY
ISO DIN HEAD UNIT PROVISION
D
Mount the rear support to the back
of the pocket with (2) #8x3/8”
Phillips screws. (Figure D)
4
5
6
Two
#8x3/8” Screws
Mount the ISO Brackets to the head
unit with the screws supplied with
the unit. (Figure E)
Slide the the head unit into the radio
opening until the side clips engage.
E
(Figure F)
Snap the Trim plate into the Radio
7
Housing. (Figure F)
F
5
Download from Www.Somanuals.com. All Manuals Search And Download.
99-8205
KIT ASSEMBLY
DOUBLE DIN HEAD UNIT PROVISION
A
NOTE: 2005-2008 Matrix not
applicable.
Cut and remove the bottom portion
(Displayed) of the mounting brack-
ets. (Figure A)
1
2
Cut and remove the center bar from
the DDIN faceplate. (Figure B)
B
Attach the ISO spacers to the
3
mounting brackets by inserting the
(4) bosses on each spacer into the
(4) holes in each bracket. (Figure C)
Attach the mounting brackets to the
DDIN head unit with the screws sup-
plied with the unit. (Figure D)
4
5
C
Attach the DDIN faceplate over the
head unit by snapping the bracket
clips into the faceplate slots.
(Figure E)
D
E
6
Download from Www.Somanuals.com. All Manuals Search And Download.
99-8205
KIT ASSEMBLY
STACKED ISO DIN HEAD UNIT PROVISION
A
NOTE: 2005-2008 Matrix not
applicable.
Cut and remove the bottom portion
(Displayed) of the mounting brack-
ets. (Figure A)
1
2
Attach the ISO spacers to the mount-
ing brackets by inserting the (4)
bosses on each spacer into the (4)
holes in each bracket. (Figure B)
B
Attach the mounting brackets to the
DDIN head unit with the screws sup-
plied with the unit. (Figure C)
3
4
Attach the DDIN faceplate over the
head unit by snapping the bracket
clips into the faceplate slots.
C
(Figure D)
D
7
Download from Www.Somanuals.com. All Manuals Search And Download.
KIT ASSEMBLY
99-8205
FINAL ASSEMBLY
Locate the factory wiring harness in the dash and make the connection as shown.
Metra recomends using the proper mating adapter and making the connections as
shown. (Isolate and individually tape off the ends of any unused wires to prevent
electrical short circuit.)
1
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
2
3
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the head
unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually
tape off ends of any unused wires to prevent electrical short circuit.
A
A)
B)
C)
D)
Strip wire ends back 1/2"
Twist ends together
Solder
B
C
D
Tape
METRA / EIA WIRING CODE
12V Ignition / Acc . . . Red
Right Front (+) . . . . . Gray
12V Batt / Memory . . Yellow
Ground . . . . . . . . . . . Black*
Power Antenna . . . . . Blue
Right Front (-). . . . . . Gray / Black
Left Front (+) . . . . . . White
Left Front (-). . . . . . . White / Black
Right Rear (+). . . . . . Violet
Amp Turn-On . . . . . . Blue / White
Amp Ground . . . . . . . Black / White
Illumination. . . . . . . . Orange
Dimmer . . . . . . . . . . Orange / White
Right Rear (-) . . . . . . Violet / Black
Left Rear (+). . . . . . . Green
Left Rear (-) . . . . . . . Green / Black
*NOTE: When Black a wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
99-8205
NOTES
9
Download from Www.Somanuals.com. All Manuals Search And Download.
INST998205
1-800-221-0932
© COPYRIGHT 2004-08 METRA ELECTRONICS CORPORATION
REV. 09/26/08
INST99-8205
Download from Www.Somanuals.com. All Manuals Search And Download.
|