40 Channel CB Radio
with 4-Watt Output Power
Model 1001z
Owner’s Manual
midlandusa.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Welcome to the World of Midland Electronics
Thank you for purchasing the state-of-the-art mobile 1001z CB Radio from Midland.
We are proud to offer you this important piece of communication equipment to help
you stay informed.
How to Install your Midland Mobile CB
This transceiver may be installed in any 12-volt negative ground-system car or truck.
Most current U.S. and foreign vehicles use a negative system, but some older
models and some newer large trucks may have a positive ground.
Check the requirements for your vehicle before you begin installation.
Generally, you have a negative-ground system if the minus ( - ) battery terminal is
connected to the motor block. Contact your dealer in the event you are unable to
determine your vehicle’s polarity system.
3
midlandusa.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Included Installation and Operating Accessories
1. Easy removal mounting bracket system.
2. Microphone bracket system.
3. All main-unit and microphone mounting hardware needed for normal installation.
4. Plug-in microphone with coil cord.
5. FCC part 95, Subpart D.
6. Owner’s Manual.
Where to Locate your CB Transceiver
Your new Midland CB is designed to be installed either under the dash or vertically
on a console of your vehicle. Safety and convenience are primary considerations in
deciding exactly where to locate your radio.
Caution: Be sure the unit is located so it does not interfere with the driver,
supplemental restraint systems (air bags), or impair access to any controls.
Connecting cables must be routed and secured in such a manner as to not interfere
with the operation of the brake, accelerator or other controls. Interference from either
the unit or connecting cables may contribute to loss of control of the vehicle.
Mechanical Mounting
1. Heeding the caution above, use the mounting bracket as a template for marking the
location of screw holes under the dash. Use an awl, nail or other sharp pointed
object to mark the hole locations.
2. Drill a 1/8” hole for each screw hole in the mounting bracket. Attach the bracket to
the dash with the Phillips head sheet metal screws provided.
Extreme care should be exercised when drilling into the dash to avoid
damage to under-dash electronic ignition, cruise control, instrument and /
or accessory wiring.
3. Position the main unit between the bracket arms in line with the retention knobs. Set
the angle for optimum operating, comfort and accessibility.
4. Tighten the retention knobs.
4
midlandusa.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Power Wiring (negative ground only)
1. If you have not determined whether your vehicle has a negative or positive ground,
do so now. Then disconnect the negative lead from the battery to prevent short
circuits that can occur during wiring. Do not connect this transceiver to positive
ground electrical systems.
2. With negative ground
A. Connect the positive (RED WIRE with in-line fuse holder) to either the (a) fuse
block, (b) cigarette lighter, or (c) directly to the positive post on your battery.
Usually, the fuse block is the most convenient connecting point. It is also
possible to connect to the Accessory terminal on the fuse block or ignition switch,
so that your CB automatically turns off when the ignition turns off.
B. Tightly connect the ground (BLACK WIRE) directly to the vehicle’s metal frame. A
good direct metal-to-metal ground is essential for optimum performance.
Installations using the cigarette lighter socket for power require an extra ground
wire from the radio chassis to the vehicle if the radio is not fastened to a
grounded part of the vehicle.
Installation of Microphone Hanger
Mounting holes are provided on the microphone hanger bracket. The bracket can be
attached to the vehicle dash, the holes provided on the left side of the radio, or other
convenient location.
Antenna
You can choose from two types of mobile CB antennas: full-length whip and loaded
whip - and a variety of mounts (depending on where you locate your antenna). The
dealer who sold you your Midland CB can advise which type is best for you.
*Where you locate your antenna does make a difference.*
Some general rules for antenna location that can aid CB performance:
1. Put your mount as high on the vehicle as possible.
The higher the proportion of antenna length that is above the roof, the better.
2. If possible, mount the antenna in the center of whatever surface you choose.
3. Keep antenna cables away from noise sources, such as the ignition system, gauges,
etc.
4. Make sure you have a solid metal-to-metal ground.
5. Exercise care to prevent cable damage.
Essentially, you have five location choices: the roof, gutter, rear deck, front cowl or
rear bumper. Where you decide to locate your antenna will determine the type of
antenna you install. Consult your Midland CB dealer for advice and guidance, and
measure your needs against the attributes of the various Midland antenna models
available.
5
midlandusa.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Antenna Installation
Follow the manufacturer’s installation instructions carefully.
Warning: Never operate your CB radio without attaching an antenna or with a
broken antenna cable. This will result in damage to transmitter circuitry.
Safety notice: The antenna used for this radio must be installed to provide a
separation distance of at least 8 in. (20cm) from all persons and must not be
co-located or operating in conjunction with any other antenna or transmitter.
Tuning Your Antenna
Some antennas are factory tuned. However, performance can usually be improved by
slightly lengthening or shortening the antenna using a Standing Wave Radio (SWR)
meter. For the exact procedures to be used, refer to the antenna manufacturer’s
installation manual.
You can buy an SWR meter separately or have your antenna checked by your Midland
CB Dealer’s service department.
Range
Essentially, the things that affect range are the same influences that optimize or limit
AM and FM broadcast signals.
Terrain: Hills, valleys and buildings naturally interrupt and shorten CB signals. In short,
anything that is between you and the person you want to talk to can shorten your CB
range. You can expect to maintain maximum transmitting/receiving performance in
flat, open country.
Weather: You can expect that CB range will be reduced – perhaps drastically – in times
of atmospheric disturbance, such as in a thunderstorm or heavy snow. Sunspots are
also known to adversely affect CB performance.
Noise
A common source of excessive noise is the ignition system. In many vehicles today the
electric fuel pump is another possible source of noise. If you suspect this is true, turn
off the ignition. With the CB in receive mode, if the noise is no longer present then
this is the source of the noise. In some cases the noise can be reduced or eliminated
by making sure the CB radio chassis is grounded. In addition to the power cord. In
extreme cases, additional grounding of components may be necessary.
6
midlandusa.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Controls
Normal /
CH9
Switch
CB/PA
Switch
S/RF
Display
TX LED Channel Display
Locking
Mic
Connector
On/Off
Volume
Channel
Selector
Squelch / RF
Knob
Microphone Connector: Plug in the supplied microphone to this connector.
Received signals will not be heard without the microphone.
ON/OFF Channel Buttons: This easy-to-operate control allows changing of CB
channels, either up or down.
Squelch Control: Adjust this control just until background noise disappears. If the
control is adjusted too far clockwise it may cause muting of weaker signals.
Channel Indicator: The LED displays the channel number.
TX LED: Indicator shows the unit is transmitting.
PA/CB Switch: When in PA mode, it causes your voice to operate the optional external
PA speaker. In CB mode, the microphone operates the transmitter.
Channel 9/Normal Switch: Allows you listen to emergency channel 9.
7
midlandusa.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Back Panel
Antenna
PA
EXT
Speaker
Jack
Connector Jack
13.8VDC
Power
Cord
Antenna Connector: Connect a standard 50-ohm CB antenna to this connector.
External Speaker Jack: When a speaker is connected to this jack, the internal
speaker is by-passed. All received signals will be heard through the external
speaker. The speaker connected to the “EXT” jack should be rated at 8 ohms and 5
watts.
PA Jack: An optional PA speaker may be attached to your transceiver through the PA
output jack on the back panel. This allows you to communicate with pedestrians or
other vehicles through your CB microphone. The speaker connected to the “PA” jack
should be rated at 8 ohms and 5 watts.
DC 13.8V Power Cord: Connects to power cord with in line 2 amp fuse.
Transceiver Operation
You should become familiar with the controls and complete the preceding installation
instructions before attempting to operate your CB.
1. Rotate the on/off volume control clockwise to turn the unit on.
2. Adjust the squelch control fully counter-clockwise so noise is heard.
3. Adjust the volume for a normal listening level.
4. Rotate the squelch control just until the noise disappears.
5. Select the desired channel.
6. To transmit, press the PTT bar on the side of the microphone. Hold the microphone
2 to 3 inches from your mouth and speak in a normal voice.
7. To receive, simply release the PTT bar.
Warning: Do not attempt to make any internal adjustments. Internal adjustments
and/or modifications can lead to illegal operation as defined by the FCC rules
and regulations, Part 95. They must be made only by qualified technical
personnel. Illegal operation can lead to serious consequences.
8
midlandusa.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Specifications
General
Frequency Range................................................................................ 26.965-27.405 MHz
Channels ......................................................................................................................... 40
Modulation Type.............................................................................................................AM
Antenna Impedance.....................................................................................................50 Ω
Loudspeaker ..................................................................................................................8 Ω
Microphone................................................................................................. 1000 Ω Electret
Power Supply...........................................................................13.8 VDC negative ground
Size .............................................................................. 4-3/8” (W) x 6-5/8” (D) x 1-7/8” (H)
Unit Weight..........................................................................................................1 lb. 10 oz
Receiver
(CB, 26.965-27.405 MHz,)
Sensitivity at 10dB S/N..............................................................................................0.7 µV
Selectivity .................................................................................................... 45dB + 10 kHz
Squelch Range...........................................................................................0.5 µV - 500 µV
Audio Output Power.............................................................2.0 W @ 8 Ω (10% distortion)
Distortion at 1000 µV......................................................................................................3%
Audio Frequency Response............................................................................400-2400 Hz
Intermediate Frequency ......................................................1st: 10.695 MHz 2nd: 455 kHz
Spurious Response..................................................................................................> 40dB
Transmitter
RF Output Power .......................................................................................................4.0 W
Frequency Tolerance...............................................................................................0.005%
Harmonic Suppression............................................................................................> 60 dB
Modulation..................................................................................................AM 90% (± 5%)
9
midlandusa.com
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAIN ENGLISH RULES
§ 95.404 (CB Rule 4) Do I need a license?
CITIZENS BAND RADIO SERVICES
You do not need an individual license to operate a CB station. You
Prepared by the Federal Communications Commission, Washington, DCare authorized by this rule to operate your CB station in accordance
FEDERAL COMMUNICATIONS COMMISSIONS
(1) Want to report an interference complaint; or
(2) Want to know if the FCC has type accepted a transmitter for
R/C.
(b) Write to the FCC, Wireless Telecommunications Bureau, Private
Wireless Division, Washington, DC 20554, if you have questions
about the R/C Rules.
with the rules in this subpart.
§ 95.405 (CB Rule 5) Where may I operate my CB station?
You are authorized to operate your CB station from:
(a) Within or over any area of the world where radio services are
regulated by the FCC. Those areas are within the territorial limits of:
(1) The fifty United States.
[48 FR 24890, June 3, 1983, as amended at
48 FR 41416, Sept. 15, 1983; 60 FR 50123, Sept. 28,1995]
Subpart D—Citizens Band (CB)
(2) The District of Columbia.
Caribbean Insular areas
(3) Common wealth of Puerto Rico.
Radio Service
(4) Navassa Island.
SOURCE: 48 FR 24894, June 3, 1983, unless otherwise noted.
(5) United States Virgin Islands (50 islets and cays).
Pacific Insular areas
GENERAL PROVISIONS
(6) American Samoa (seven islands).
(7) Baker Island.
§ 95.401 (CB Rule 1) What are the Citizens Band Radio
Services?
(8) Commonwealth of Northern Marian Islands.
(9) Guam Island.
The Citizens Band Radio Services are:
(10) Howland Island.
(a) The Citizens Band (CB) Radio Service—a private, two-way,
shortdistance voice communications service for personal or
business activities of the general public. The CB Radio Service may
also be used for voice paging.
(b) The Family Radio Service (FRS)—a private, two-way, very
short-distance voice communications service for facilitating family
and group activities. The rules for this service are contained in
subpart B of this part.
(c) The Low Power Radio Service (LPRS)—a private, short-distance
communication service providing auditory assistance to persons
with disabilities, persons who require language translation, and
persons in educational settings, health care assistance to the ill, law
enforcement tracking services in cooperation with law enforcement,
and point-to-point network control communications for Automated
Marine Telecommunications System (AMTS) coast stations licensed
under part 80 of this chapter. The rules for this service are listed
under subpart G of this part. Two-way voice communications are
prohibited. [61 FR 28769, June 6, 1996, as amended at 61 FR
46566, Sept. 4, 1996]
(11) Jarvis Island.
(12) Johnston Island (Islets East, Johnston, North and Sand).
(13) Kingman Reef.
(14) Midway Island (Islets Eastern and Sand).
(15) Palmyra Island (more than 50 islets).
(16) Wake Island (Islets Peale, Wake and Wilkes).
(b) Any other area of the world, except within the territorial limits of
areas where radio services are regulated by—
(1) An agency of the United States other than the FCC. (You are
subject to its rules.)
(2) Any foreign government. (You are subject to its rules.)
(c) An aircraft or ship, with the permission of the captain, within or
over any area of the world where radio services are regulated by
the FCC or upon or over international waters. You must operate
your CB station according to any applicable treaty to which the
United States is a party.
§ 95.406 (CB Rule 6) Are there any special restrictions on the
location of my CB station?
(a) If your CB station is located on premises controlled by the
Department of Defense you may be required to comply with
additional regulations imposed by the commanding officer of the
installation.
(b) If your C/B station will be constructed on an environmentally
sensitive site, or will be operated in such a manner as to raise
environmental problems, under § 1.1307 of this chapter, you must
provide an environmental assessment, as set forth in § 1.1311 of
this chapter, and undergo the environmental review, § 1.1312 of this
chapter, before commencement of construction.
§ 95.402 (CB Rule 2) How do I use these rules?
(a) You must comply with these rules (See CB Rule 21 § 95.421, for
the penalties for violations) when you operate a station in the CB
Service from:
(1) Within or over the territorial limits of places where radio services
are regulated by the FCC (see CB Rule 5, § 95.405);
(2) A board any vessel or aircraft registered in the United States; or
(3) Aboard any unregistered vessel or aircraft owned or operated by
a United States citizen or company.
(b) Your CB station must comply with technical rules found in
subpart E of part 95.
(c) Where the rules use the word ‘‘you’’, ‘‘you’’ means a person
operating a CB station.
[48 FR 24894, June 3, 1983, as amended at 55 FR 20398, May 16,
1990]
(d) Where the rules use the word ‘‘person,’’ the rules are concerned
with an individual, a corporation, a partnership, an association, a
joint stock company, a trust, a state, territorial or local government
unit, or other legal entity.
(e) Where the rules use the term ‘‘FCC’’, that means the Federal
Communications Commission.
HOW TO OPERATE A CB STATION
§ 95.407 (CB Rule 7) On what channels may I operate?
(a) Your CB station may transmit only on the following channels
(frequencies):
(f) Where the rules use the term ‘‘CB station’’, that means a radio
station transmitting in the CB Radio Service.
§ 95.403 (CB Rule 3) Am I eligible to operate a CB station?
You are authorized to operate a CB station unless:
(a) You are a foreign government, are representative of a foreign
government, or a federal government agency; or
(b) The FCC has issued a cease and desist order to you, and the
order is still in effect.
Download from Www.Somanuals.com. All Manuals Search And Download.
antenna. Consult part 17 of the FCC’s Rules for more information.
WARNING:———————————————————
Installation and removal of CB station antennas near power lines
is dangerous. For your safety, follow the installation directions
included with your antenna.
Frequency
Channel
(megahertz - MHz)
1
26.965
2
26.975
3
26.985
4
27.005
5
27.015
————————————————————————
6
27.025
7
27.035
[48 FR 24894, June 3, 1983, as amended at 48 FR 41416, Sept.
15, 1983]
8
27.055
1
9
27.065
10
27.075
27.085
27.105
27.115
27.125
27.135
27.155
27.165
27.175
27.185
27.205
27.215
27.225
27.255
27.235
27.245
27.265
27.275
27.285
27.295
27.305
27.315
27.325
27.335
27.345
27.355
27.365
27.375
27.385
27.395
27.405
11
§ 95.409 (CB Rule 9) What equipment may I use at my CB
station?
12
13
14
(a) You must use an FCC type-accepted CB transmitter at your CB
station. You can identify an FCC type-accepted transmitter by the
type-acceptance label placed on it by the manufacturer. You may
examine a list of type-accepted equipment at any FCC Field Office
or at FCC Headquarters. Use of a transmitter which is not FCC
type-accepted voids your authority to operate the station.
(b) You must not make, or have made, any internal modification to
a typeaccepted CB transmitter. (See CB Rule 25, §95.425). Any
internal modification to a type-accepted CB transmitter cancels the
type-acceptance, and use of such a transmitter voids your authority
to operate the station.
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
§ 95.410 (CB Rule 10) How much power may I use?
(a) Your CB station transmitter power output must not exceed the
following values under any conditions: AM (A3)—4 watts (carrier
power) SSB—12 watts (peak envelope power)
(b) If you need more information about the power rule, see the
technical rules in subpart E of part 95.
31
32
33
34
35
36
37
38
(c) Use of a transmitter which has carrier or peak envelope power in
excess of that authorized voids your authority to operate the station.
39
40
1
See paragraph (b) of this section
§ 95.411 (CB Rule 11) May I use power amplifiers?
(a) You may not attach the following items (power amplifiers) to your
typeaccepted CB transmitter in any way:
(1) External radio frequency (RF) power amplifiers (sometimes
called linears or linear amplifiers); or
(2) Any other devices which, when used with a radio transmitter as
a signal source, are capable of amplifying the signal.
(b) There are no exceptions to this rule and use of a power amplifier
voids your authority to operate the station.
(c) The FCC will presume you have used a linear or other external
RF power amplifier if—
(1) It is in your possession or on your premises; and
(2) There is other evidence that you have operated your CB station
with more power than allowed by CB Rule 10, § 95.410.
(d) Paragraph (c) of this section does not apply if you hold a license
in another radio service which allows you to operate an external RF
power amplifier.
(b) Channel 9 may be used only for emergency communications or for
traveler assistance.
(c) You must, at all times and on all channels, give priority to
emergency communication messages concerning the immediate
safety of life or the immediate protection of property.
(d) You may use any channel for emergency communications or for
traveler assistance.
(e) You must share each channel with other users.
(f) The FCC will not assign any channel for the private or exclusive
use of any particular CB station or group of stations.
(g) The FCC will not assign any channel for the private or exclusive
use of CB stations transmitting single side-band or AM.
§ 95.408 (CB Rule 8) How high may I put my antenna?
(a) Antenna means the radiating system (for transmitting, receiving
or both) and the structure holding it up (tower, pole or mast). It also
means everything else attached to the radiating system and the
structure.
(b) If your antenna is mounted on a handheld portable unit, none of
the following limitations apply.
(c) If your antenna is installed at a fixed location, it (whether
receiving, transmitting or both) must comply with either one of the
following:
(1) The highest point must not be more than 6.10 meters (20 feet)
higher than the highest point of the building or tree on which it is
mounted; or
(2) The highest point must not be more than 18.3 meters (60 feet)
above the ground.
(d) If your CB station is located near an airport, and if you antenna
structure is more than 6.1 meters (20 feet) high, you may have to
obey additional restrictions. The highest point of your antenna must
not exceed one meter above the airport elevation for every hundred
meters of distance from the nearest point of the nearest airport
runway. Differences in ground elevation between your antenna and
the airport runway may complicate this formula. If your CB station is
near an airport, you may contact the nearest FCC field office for a
worksheet to help you figure the maximum allowable height of your
§ 95.412 (CB Rule 12) What communications may be
transmitted?
(a) You may use your CB station to transmit two-way plain language
communications. Two-way plain language communications are
communications without codes or coded messages. Operating
signals such as ‘‘ten codes’’ are not considered codes or
coded messages. You may transmit two-way plain language
communications only to other CB stations, to units of your own CB
station or to authorized government stations on CB frequencies
about—
(1) Your personal or business activities or those of members of your
immediate family living in your household;
(2) Emergencies (see CB Rule 18, § 95.418)
(3) Traveler assistance (see CB Rule 18, § 95.418); or
(4) Civil defense activities in connection with official tests or drills
conducted by, or actual emergencies announced by, the civil
defense agency with authority over the area in which your station is
located.
(b) You may use your CB station to transmit a tone signal only when
Download from Www.Somanuals.com. All Manuals Search And Download.
the signal is used to make contact or to continue communications.
(Examples of circuits using these signals are tone operated squelch
and selective calling circuits.) If the signal is an audible tone, it
must last no longer than 15 seconds at one time. If the signal is a
subaudible tone, it may be transmitted continuously only as long as
you are talking.
of the following means:
(1) Previously assigned CB call sign;
(2) K prefix followed by operator initials and residence zip code;
(3) Name; or
(4) Organizational description including name and any applicable
operator unit number.]
(c) You may use your CB station to transmit one-way
communications (messages which are not intended to establish
communications between two or more particular CB stations) only
for emergency communications, traveler assistance, brief tests
(radio checks) or voice paging.
(c) [You are encouraged to use your ‘‘handle’’ only in conjunction
with the methods of identification listed in paragraph (b) of this
section.]
§ 95.418 (CB Rule 18) How do I use my CB station in an
emergency or to assist a traveler?
§ 95.413 (CB Rule 13) What communications are prohibited?
(a) You must not use a CB station—
(a) You must at all times and on all channels, give priority to
emergency communications.
(1) In connection with any activity which is against federal, state or
local law;
(2) To transmit obscene, indecent or profane words, language or
meaning;
(b) When you are directly participating in emergency
communications, you do not have to comply with the rule about
length of transmissions (CB Rule 16, § 95.416). You must obey all
other rules.
(3) To interfere intentionally with the communications of another CB
station;
(4) To transmit one-way communications, except for emergency
communications, traveler assistance, brief tests (radio checks), or
voice paging;
(5) To advertise or solicit the sale of any goods or services;
(6) To transmit music, whistling, sound effects or any material to
amuse or entertain;
(c) You may use your CB station for communications necessary
to assist a traveler to reach a destination or to receive necessary
services. When you are using your CB station to assist a traveler,
you do not have to obey the rule about length of transmissions (CB
Rule 16, § 95.416). You must obey all other rules.
(d) You may use your CB station to transmit one-way
communications concerning highway conditions to assist travelers.
(7) To transmit any sound effect solely to attract attention;
(8) To transmit the word ‘‘MAYDAY’’ or any other international
distress signal, except when your station is located in a ship, aircraft
or other vehicle which is threatened by grave and imminent danger
and your are requesting immediate assistance;
(9) To communicate with, or attempt to communicate with, any CB
station more than 250 kilometers (155.3 miles) away;
(10) To advertise a political candidate or political campaign; (you
may use your CB radio for the business or organizational aspects of
a campaign, if you follow all other applicable rules);
(11) To communicate with stations in other countries, except
General Radio Service stations in Canada; or
(12) To transmit a false or deceptive communication.
(b) You must not use a CB station to transmit communications
for live or delayed rebroadcast on a radio or television broadcast
station. You may use your CB station to gather news items or to
prepare programs.
[48 FR 24894, June 3, 1983, as amended at 57 FR 22442, May 28,
1992]
§ 95.419 (CB Rule 19) May I operate my CB station transmitter
by remote control?
(a) You may not operate a CB station transmitter by radio remote
control.
(b) You may operate a CB transmitter by wire line remote control if
you obtain specific approval in writing from the FCC. To obtain FCC
approval, you must show why you need to operate your station by
wire line remote control. Send your request and justification to FCC,
1270 Fairfield Road, Gettysburg, PA 17325–7245. If you receive
FCC approval, you must keep the approval as part of your station
records.(See CB Rule 27, §95.427.)
(c) Remote control means operation of a CB transmitter from
any place other than the location of the CB transmitter. Direct
mechanical control or direct electrical control by wire from some
point on the same premises, craft or vehicle as the CB transmitter is
not considered remote control.
§95.414 (CB Rule 14) May I be paid to use my CB station?
(a) You may not accept direct or in-direct payment for transmitting
with a CB station.
(b) You may use a CB station to help you provide a service, and be
paid for that service, as long as you are paid only for the service
and not for the actual use of the CB station.
[48 FR 24894, June 3, 1983, as amended at 57 FR 40343, Sept. 3,
1992]
§ 95.420 (CB Rule 20) May I connect my CB station transmitter
to a telephone?
§ 95.415 (CB Rule 15) Who is responsible for communications
I make?
(a) You may connect your CB station transmitter to a telephone if
you comply with all of the following:
You are responsible for all communications which are made by you
from a CB station.
(1) You or someone else must be present at your CB station and
must—
(i) Manually make the connection (the connection must not be made
by remote control);
(ii) Supervise the operation of the transmitter during the connection;
(iii) Listen to each communication during the connection; and
(iv) Stop all communications if there are operations in violation of
these rules.
(2) Each communication during the telephone connection must
comply with all of these rules.
(3) You must obey any restriction that the telephone company
places on the connection of a CB transmitter to a telephone.
(b) The CB transmitter you connect to a telephone must not be
shared with any other CB station.
§ 95.416 (CB Rule 16) Do I have to limit the length of my
communications?
(a) You must limit your CB communications to the minimum
practical time.
(b) If you are communicating with another CB station or stations,
you, and the stations communicating with you, must limit each of
your conversations to no more than five continuous minutes.
(c) At the end of your conversation, you, and the stations
communicating with you, must not transmit again for at least one
minute.
§ 95.417 (CB Rule 17) Do I identify my CB communications?
(a) You need not identify your CB communications.
(c) If you connect your CB transmitter to a telephone, you must use
a phone patch device with has been registered with the
(b) [You are encouraged to identify your CB communications by any
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC. OTHER THINGS YOU NEED TO KNOW
qualified to perform transmitter maintenance and repair duties in the
private land mobile services and fixed services by an organization
or committee representative of users in those services.
(c) Except as provided in paragraph (d) of this section, each
internal repair and each internal adjustment of a CB transmitter in
which signals are transmitted must be made using a non-radiating
(‘‘dummy’’) antenna.
(d) Brief test signals (signals not longer than one minute during any
five minute period) using a radiating antenna may be transmitted in
order to:
(1) Adjust an antenna to a transmitter;
(2) Detect or measure radiation of energy other than the intended
signal; or
(3) Tune a receiver to your CB transmitter. (Secs. 4(i) and 303(r),
Communications Act of 1934, as amended, 47 U.S.C. 154(i) and
303(r), and sec. 553 of the Administrative Procedures Act, 5 U.S.C.
553)
§ 95.421 (CB Rule 21) What are the penalties for violating these
rules?
(a) If the FCC finds that you have willfully or repeatedly violated the
Communications Act or the FCC Rules, you may have to pay as
much as $10,000 for each violation, up to a total of $75,000. (See
section 503(b) of the Communications Act.)
(b) If the FCC finds that you have violated any section of the
Communications Act or the FCC Rules, you may be ordered to stop
whatever action caused the violation. (See section 312(b) of the
Communications Act.)
(c) If a Federal court finds that you have willfully and knowingly
violated any FCC Rule, you may be fined up to $500 for each
day you committed the violation. (See section 502 of the
Communications Act.)
(d) If a Federal court finds that you have willfully and knowingly
violated any provision of the Communications Act, you may be fined
up to $10,000 or you may be imprisoned for one year, or both. (See
section 501 of the Communications Act.)
[48 FR 24894, June 3, 1983, as amended at 49 FR 20673, May 16,
1984]
[48 FR 24894, June 3, 1983, as amended at 57 FR 40343, Sept. 3,
1992]
§ 95.425 (CB Rule 25) May I make any changes to my CB
station transmitter?
(a) You must not make or have anyone else make any internal
modification to your CB transmitter.
(b) Internal modification does not include:
§ 95.422 (CB Rule 22) How do I answer correspondence from
the FCC?
(a) If it appears to the FCC that you have violated the
Communications Actor these rules, the FCC may send you a
discrepancy notice.
(b) Within the time period stated in the notice, you must answer
with:
(1) A complete written statement about the apparent discrepancy;
(2) A complete written statement about any action you have taken
to correct the apparent violation and to prevent it from happening
again; and
(1) Repair or servicing of a CB station transmitter (see CB Rule 24,
§ 95.424); or
(2) Changing plug-in modules which were type accepted as part of
your CB transmitter.
(c) You must not operate a CB transmitter which has been modified
by anyone in any way, including modification to operate on
unauthorized frequencies or with illegal power. (See CB Rules 9
and 11, §§ 95.409 and 95.411.)
(3) The name of the person operating at the time of the apparent
violation.
§ 95.426 (CB Rule 26) Do I have to make my CB station
available for inspection?
(c) If the FCC sends you a letter asking you questions about your
CB radio station or its operation, you must answer each of the
questions with a complete written statement within the time period
stated in the letter.
(a) If an authorized FCC representative requests to inspect your CB
station, you must make your CB station and records available for
inspection.
(b) A CB station includes all of the radio equipment you use.
(d) You must not shorten your answer by references to other
communications or notices.
(e) You must send your answer to the FCC office which sent you
the notice.
(f) You must keep a copy of your answer in your station records.
(See CB Rule 27, § 95.427.)
§ 95.427 (CB Rule 27) What are my station records?
Your station records include the following documents, as applicable.
(a) A copy of each response to an FCC violation notice or an FCC
letter. (See CB Rule 22, § 95.422.)
(b) Each written permission received from the FCC. (See CB Rule
19,
§ 95.423 (CB Rule 23) What must I do if the FCC tells me that
my CB station is causing interference?
§ 95.419.)
(a) If the FCC tells you that your CB station is causing interference
for technical reasons you must follow all instructions in the official
FCC notice. (This notice may require you to have technical
adjustments made to your equipment.)
(b) You must comply with any restricted hours of CB station
operation which may be included in the official notice.
§ 95.428 (CB Rule 28) How do I contact the FCC?
(a) Write to your nearest FCC Field Office if you:
(1) Want to report an interference complaint; or
(2) Want to know if the FCC has typeaccepted a transmitter for CB.
(b) Write to the FCC, Wireless Telecommunications Bureau, Private
Wireless Division, Washington, DC 20554, if you have questions
about the RC Rules.
§ 95.424 (CB Rule 24) How do I have my CB station transmitter
serviced?
[48 FR 24894, June 3, 1983, as amended at 48 FR 41416, Sept.
15, 1983; 60 FR 50123,
(a) You may adjust an antenna to your CB transmitter and you may
make radio checks. (A radio check means a one way transmission
for a short time in order to test the transmitter.)
Sept. 28,1995]
(b) You are responsible for the proper operation of the station at
all times and are expected to provide for observations, servicing
and maintenance as often as may be necessary to ensure proper
operation. You must have all internal repairs or internal adjustments
to your CB transmitter made in accordance with the Technical
Regulations (see subpart E). The internal repairs or internal
adjustments should be performed by or under the immediate
supervision and responsibility of a person certified as technically
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
If you have a problem which you believe requires service, please first check the FAQ
section of the website, check your Owner’s Manual, or call and speak with a service
technician. Many problems can be remedied without returning the unit for service. If
necessary, return as follows:
Pack the unit in its original box and packing. Then pack the original box in a suitable
shipping carton. Caution: Improper packing may result in damage during shipment.
Include the following:
a. Full description of any problems
b. Daytime telephone number, name & address
For warranty service include a photocopy of the bill of sale from an authorized dealer or
other proof of purchase showing the date of sale.
You do not need to return accessory items (AC/DC Adapter, Batteries, and Owners
Guide) unless they might be directly related to the problem.
Repairs not covered by warranty or units that are over THREE year old are subject to a
repair fee. Please call for a quote on repair service cost at 816-241-8500. Send only
cashier’s check, money order, Master Card or Visa card number.
Midland Radio Corporation
Hereby certifies that this unit has
been designed, manufactured,
FCC type accepted and certified
in accordance with Part 95 and
Part 15, Subpart C of the current
FCC rules and regulations as of
the date of manufacture.
MIDLAND RADIO CORPORATION
5900 Parretta Drive
Kansas City, MO 64120
Phone 816-241-8500
E-mail: [email protected]
Printed in China
14
midlandusa.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Limited Warranty
Subject to the exclusions set forth below, Midland Radio Corporation will repair or replace, at
its option without charge, any Midland CB Radio which fails due to a defect in material or
workmanship within Three Years following the initial consumer purchase.
This warranty does not apply to water damage, battery leak, abuse or misuse of unauthorized
accessories, unauthorized service or modification or altered products. Accessories have a
90 day warranty from date of purchase, including any chargers, mounts, and cables.
This warranty does not include the cost of labor for removal or re-installation of the product in
a vehicle or other mounting.
ANY IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
SHALL BE LIMITED AS SET FORTH HEREIN AND TO THE DURATION OF THE
LIMITED WARRANTY, OTHERWISE THE REPAIR OR REPLACEMENT AS PROVIDED
UNDER THIS EXPRESS LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF THE
CONSUMER AND IS PROVIDED IN LIEU OF ALL OTHER WARRANTIES, EXPRESS
OR IMPLIED. IN NO EVENT SHALL MIDLAND BE LIABLE, WHETHER IN CONTRACT
OR TORT (INCLUDING BUT NOT LIMITED TO NEGLIGENCE, GROSS NEGLIGENCE,
BODILY INJURY, PROPERTY DAMAGE AND DEATH) FOR DAMAGES IN EXCESS OF
THE PURCHASE PRICE OF THE PRODUCT OR ACCESSORY, OR FOR ANY INDIRECT,
INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY KIND, OR LOSS OF
REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS OF INFORMATION OR DATA OR
OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE ABILITY
OR INABILITY TO USE THE PRODUCTS OR ACCESSORIES TO THE FULL EXTENT
THESE DAMAGES MAY BE DISCLAIMED BY LAW.
For Product Purchased in the USA:
Performance of any obligation under this warranty may be obtained by returning the
warranted product, prepaid freight, along with proof of purchase to:
Midland Radio Corporation
Warranty Service Department
5900 Parretta Drive
Kansas City, MO 64120
This warranty gives you specific legal rights, and you may also have other rights, which vary
from state to state.
Note: The above warranty applies only to merchandise purchased in the United States of
America or any of the territories or possessions thereof, or from a U.S. Military exchange.
For Product Purchased in Canada:
Performance of any obligation under this warranty may be obtained by returning the
warranted product, along with proof of purchase, to your place of purchase in Canada.
This warranty gives you specified legal rights. Additional warranty rights may be provided by
law in some within Canada.
Download from Www.Somanuals.com. All Manuals Search And Download.
HD Wearable Video Cameras
2-Way Radios
Weather Radios
Bluetooth Headsets
Marine Radios
Emergency Crank Radios
CB Radios
Check out these and other great products at
midlandusa.com
Download from Www.Somanuals.com. All Manuals Search And Download.
|