STEREO SIMUL-CLASS 2:90
Operating Manual
1
Download from Www.Somanuals.com. All Manuals Search And Download.
FRONT PANEL
One look at the 2:90's front panel probably told you "easy to use" ... right? We think so... but
after a closer look, you notice three small LED's labeled - "Deep, 1/2 Drive, and Modern."
Since the rest of the Front Panel is virtually self explanatory... let us first explain these three
mystery lights. Following the law of "less is more", we decided that what you can't see can't
confuse you. Spin the 2:90 around. See the box in the lower left corner labeled “Voicing
Switch”? These three jacks are connected to the three mystery lights on the Front Panel.
They each activate one Voicing Feature - and a light! All you have to do is connect any "tip to
ground" switching jack to these and you can audition each of these features individually or
combine them for the most radical tone shaping experience you ever heard come from a
power amp. These Voicings are best suited for distortion sounds, but please... experiment...
clean sounds can become great solo sounds simply by triggering one or more of these
features. Before we go into what each of the voicings are and how to use them, a quick word
on Pre-amps - namely the Pre-amp the 290 was designed to power and enhance. TriAxis.
TriAxis, MESA/Boogie's long awaited all tube Midi Programmable Pre-amp, was designed to
control the voicing features of all MESA "SwitchTrack Stereo amplifiers" and the Simul 2:90
Stereo power amplifier. As well as 8 programmable modes and a programmable effects loop,
TriAxis incorporates a switching Matrix of 4 "collector to ground" type switches that appear on
the TriAxis rear panel as four 1/4" mono jacks labeled “Switch 1-2-3-4”. These jacks can be
activated at the Loop/SW key on the TriAxis Front Panel individually or all at once and then
stored under a preset number. Connect switches 1, 2 & 3 to the 290's voicing features and
you're ready to go. Pressing the key toggles TriAxis' FX Loop and Function Switches through
every possible combination of Loop and Switch. When the LED for the desired function
switch lights up in the lower right corner, you may audition the voicing feature on the power
amp you have chosen with the preset you are currently using on TriAxis. The possibilities are
endless. Any type of cable is fine for this switching operation. It need not be shielded signal
cable.
If all this hidden versatility is a bother to you, guess what... YOU don't have to use the voicing
features and you'll still get the best Tone you've probably ever heard out of your rig. But just
in case you ever get brave or you just want to have some fun exploring... read on.
DEEP
This LED indicates that the Deep function has been activated. To trigger this function - simply
connect one of the TriAxis Switch jacks to the 1/4" jack labeled "Deep" on the jack panel at
the left rear side of the 2:90. Program the TriAxis corresponding switch to be on
under the desired preset. You should now hear the Deep function. The low end fundamental
will get lower and "breathier" and the high end will sound warmer and more three
dimensional. The Deep feature enhances both clean and distorted sounds equally, so
experiment to your liking. NOTE: If you are using the 290 with another Pre-Amp and not a
TriAxis, you may use a standard tip to ground switch to trigger the Deep or any of the three
voicing features.
NOTE: MESA/BOOGIE STUDIO PRE-AMP OWNERS: The Channel Switching jack labeled
"Footswitch” on both front and back panels of your Pre-Amp are wired in parallel. Since you
probably need only one footswitch, the other unused jack could be connected to any of the
three voicing features. The logic may not work to your preference ... but there may be
situations where only one feature is necessary and this trick could be applied.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
1/2 DRIVE
Like Deep, this LED indicates the 1/2 Drive mode has been selected. Again - connect the
TriAxis switch jack to the 1/2 Drive jack on the rear left of the 290. Program it to be activated
under the desired preset. When 1/2 drive is activated the 2:90's overall output is reduced by
roughly half and you will hear the volume drop correspondingly. Notice that the top end gets
a little brighter in a higher frequency and just starts to break up. When listening to 1/2 Drive
pushing a clean sound these break-up brights may seem excessive. Switching to a high gain
sound however, tells the real story right away! The top end gets softer and the harmonies line
up and start to dance. The whole amp gets spongier and feels easier to play. When using 1/2
Drive for giant crunch chords it provides the haze that's hard to beat, especially when used in
conjunction with the Deep feature. Half Drive was originally conceived as a way to get more
gain from the power section to combine with high gain sounds in the preamp. This works
beautifully. There is, however, another great way to put this feature to work that is easily
overlooked. Dial up a clean sound from the pre-amp, then increase the front end gain as high
as possible without pushing it into full blown distortion ... you know, just to the threshold of
distortion. Trigger the 112 Drive to unleash a truly cool and bluesy medium gain lead sound.
Darken or brighten to taste either at the tone controls or with the 2:90 presence controls. With
an "analog" (non-programmable) pre-amp this becomes a useful "extra mode". With TriAxis
many such possibilities await. As we mentioned earlier, engaging the 1/2 Drive causes a
volume decrease. This is a possible problem only to non-TriAxis owners. Since the 2:90 was,
from its inception, the TriAxis counterpart in a "system" to other pre-amp owners, we now
apologize for any inconvenience and hope you make a B-line to your nearest MESA/Boogie
Pro Center straight away to hear the TriAxis. To all you TriAxis owners, you will soon find this
"could be fault" a truly great feature! You've now doubled all your great programs at lower
volumes, great for choruses where the vocal needs to stand out but you want more gain or
"intensity". Or you might program the TriAxis Master higher and whip the 2:90 in 1/2 Drive
harder for that extra grind when moshing. Whatever your individual application, 1/2 Drive will
enhance the 2:90's already toneful nature greatly.
MODERN
Again, this LED indicates the Modern voicing feature has been selected. Derived from the
presence shift switches found on our Mark IV amplifier, and the "Red" or Modern Channel of
our Dual Rectifier Solo Head, this sound pushes at the boundaries of today's high gain
crunch. To the tame and timid, Modern is a scary sound. It is the opposite of soft... it's hard...
hard core aggression. If you love to get way agro with super gained out crunch, Modern will
re-focus your attack and clean up the slop. Often times when trying to dial the amount of gain
necessary to get the scream and grind... you quickly find the low notes falling apart or
becoming too washy. Modern is the cure for "anemic chunk”. It places emphasis on the
percussive mids and highs and tightens those flubby lows where they tighten up right at the
power section. Modern also provides a little more headroom resulting in a volume increase.
When Modern is used in conjunction with Half Drive there is virtually no volume change and
the benefits of both are incorporated to achieve more gain, more aggression, more
harmonics, more scoop, more attack etc. Then try the ultimate enhancement Deep, Half Drive
and Modern! We'll spare the adjectives ... just try it out and you'll see why we think this is the
most advanced and easiest to use two spaces of Tone Power on the planet.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
LEVEL A/B
These two pots control the volume level of each side or channel of the 2:90. Since there's
only one Standby Switch on this unit they may also be useful as channel muting controls.
NOTE: If only one speaker is to be used on one channel and no speaker load on the other,
always turn the unused channel’s Level Control to zero. To prevent oscillation (motorboating)
turn the Presence Control of that channel all the way up.
PRESENCE A/B
These controls "open up" the 2:90 producing brightness and sparkle for clean sounds at
higher settings or sizzle and edge when set high for distortion sounds. At lower Presence
settings you can darken and compress lead sounds making them warmer and fatter. Turning
the presence controls to zero "chokes the brights" completely, making the 2:90 great for jazz
clean sounds or round vocal lead work.
POWER/STANDBY
These two toggles located next to the Presence controls deliver A.C. Mains voltage and D.C.
filament voltage. When powering up cold - always turn the power on first - wait 30 seconds -
then turn the Standby on. This procedure reduces shock on cold tubes and prolongs tube life.
Remembering to use the Standby on set breaks also prolongs tube life. NOTE: Power tube
life varies depending on many factors i.e. how much you play, how long you play, how you
treat your equipment etc. We've found that most discerning pro's who use their gear five to
seven nights a week start noticing some tone loss somewhere around 8 months to a year.
Some people, however, use the same set of power tubes for years with no complaints. We
recommend changing your power tubes once a year if you play a lot. This way you're
ensured of smooth operation and optimum tone. Always use MESA power tubes of matching
color codes whenever possible. These are matched correctly and hammer tested, and
actually cost less than the so called matched competitors in most cases. Also, it keeps your
2:90's warranty intact.
MAIN FUSE
The recessed grey fuse cap located above the Pilot light holds the 290's main fuse. Should
this fuse blow, replace it with SLO-BLO type of an appropriate rating. Domestic and Canada
use 6 1/4 amp SLO-BLO. Disregard the 4 amp labeling - this is for units not wired for 117v
operation.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
BACK PANEL
Now that we've mastered the Front Panel and found its simple layout easily digested let's
move aft for some jacks and tubes. Let's take the connections first and start with the jack
panel.
INPUTS B/A:
Here in the upper left corner of the jack panel you'll find two 1/4” insulated jacks. These are
the inputs for pre-amps and/or effects, depending on how you wire your system. You may
drive the 2:90 with your pre-amp directly or choose to come from the last effect in a chain and
drive the power amp this way. Either way is fine and up to your preference.
We have also provided an input sensitivity switch that toggles you between instrument level
and the less sensitive line level position. If you have too much signal in your system by the
time you get to the 2:90, use Line Level. This tends to be the more common position. If your
Pre-amp doesn't have enough send level or you want to plug a guitar straight into the 2:90
use Instrument Level. Yes... you did hear right, you can plug right into the 2:90 with a good
guitar and get a sweet clean rhythm sound. Crank the level all the way up and check out a
vintage solo sound. Use the voicing features in this setup and you just may find yourself
wondering what you need a pre-amp for! Seriously though, the 2:90 all by itself could and
has been used as a stand alone guitar amp. Try that with your standard solid state power
amp!
VOICING SWITCHES
As mentioned in the Front Panel section; these are the 1/4” jacks that trigger the 2:90's three
voicing features. They are described earlier under Deep, Half-Drive and Modern. Again, they
are activated with a "tip to ground" or "collector to ground" type switch. TriAxis owners find
these jacks especially useful, as they can trigger any or all of these features with the on board
function switches and store these settings under a program number. If you don't own a
TriAxis... order one... now, or use any "tip to ground" on/off switch. Shielded cable need not
be used.
SPEAKERS
These six jacks deliver the 2:90's incredible tone to your favorite speaker cabinets. One eight
ohm and two four ohm jacks per channel are provided. Use one eight ohm cabinet in the
eight ohm jack. Use two eight ohm cabinets into the two four ohm jacks. Use one four ohm
cabinet into one four ohm jack. Use one sixteen ohm cabinet into the eight ohm jack. Two
sixteen ohm cabinets into a "y" cable works even better in the eight ohm jack. This should
cover most all the popular speaker configurations. Don't forget: Duplicate the proper load for
both channels: Turn it’s Level control to zero and its Presence control all the way up. It's also
best not to send signal to the unused channel input.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
|