MP8800
User’s Guide
Portable CD Player with
AM/FM Stereo Radio
Before operating this product,
please read these instructions completely.
Download from Www.Somanuals.com. All Manuals Search And Download.
INFORMATION:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT
EXPOSE THIS UNIT TO RAIN OR MOISTURE.
LASER SAFETY: This unit employs a laser. Only qualified service personnel
should attempt to service this device due to possible eye injury.
CAUTION: USE OF CONTROLS, ADJUSTMENTS OR PERFORMANCE
PROCEDURE HEREIN MAY RESULT IN HAZARDOUS RADIATION
EXPOSURE.
SURGE PROTECTORS:
It is recommended to use a surge protector for AC connection. Lightning and
power surges ARE NOT covered under warranty for this product.
Download from Www.Somanuals.com2. All Manuals Search And Download.
Dear Customer:
Selecting fine audio equipment such as the unit you’ve just purchased is only the start of
your musical enjoyment. Now it’s time to consider how you can maximize the fun and
excitement your equipment offers. This manufacturer and the Electronic Industries
Association’s Consumer Electronics Group want you to get the most out of your equip-
ment by playing it at a safe level. One that lets the sound come through loud and clear
without annoying blaring or distortion and, most importantly, without affecting your sensi-
tive hearing.
Sound can be deceiving. Over time your hearing “comfort level” adapts to higher volumes
of sound. So what sounds “normal” can actually be loud and harmful to your hearing. Guard
against this by setting your equipment at a safe level BEFORE your hearing adapts.
To establish a safe level:
• Start your volume control at a low setting.
• Slowly increase the sound until you can hear it comfortably and clearly, and without dis-
tortion.
Once you have established a comfortable sound level:
• Set the dial and leave it there.
Taking a minute to do this now will help to prevent hearing damage or loss in the future.
After all, we want you listening for a lifetime.
We Want You Listening For A Lifetime
Used wisely, your new sound equipment will provide a lifetime of fun and enjoyment. Since
hearing damage from loud noise is often undetectable until it is too late, this manufacturer
and the Electronic Industries Association’s Consumer Electronics Group recommend you
avoid prolonged exposure to excessive noise. This list of sound levels is included for your
protection.
Decibel
Level
30
Example
Quiet library, soft whispers
40
50
60
70
Living room, refrigerator, bedroom away from traffic
Light traffic, normal conversation, quiet office
Air conditioner at 20 feet, sewing machine
Vacuum cleaner, hair dryer, noisy restaurant
Average city traffic, garbage disposals, alarm clock at two feet
80
THE FOLLOWING NOISES CAN BE DANGEROUS UNDER CONSTANT EXPOSURE:
90
Subway, motorcycle, truck traffic, lawn mower
Garbage truck, chain saw, pneumatic drill
Rock band concert in front of speakers, thunderclap
Gunshot blast, jet engine
100
120
140
180
Rocket launching pad
EIA
Information courtesy of the Deafness Research Foundation.
EST. 1924
We
WantYou
LISTENING
ForALifetime
Download from Www.Somanuals.com3. All Manuals Search And Download.
SAFETY INSTRUCTIONS
Before using the unit, be sure to read all operating instructions carefully. Please note that these are
general precautions and may not pertain to your unit. For example, this unit may not have the capabili-
ty to be connected to an outdoor antenna.
1. READ INSTRUCTIONS
All the safety and operating instructions should be read before the product is operated.
2. RETAIN INSTRUCTIONS
The safety and operating instructions should be retained for future reference.
3. HEED WARNINGS
All warnings on the product and in the operating instructions should be adhered to.
4. FOLLOW INSTRUCTIONS
All operating and use instructions should be followed.
5. CLEANING
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
Use a dry cloth for cleaning.
6. ATTACHMENTS
Do not use attachments not recommended by the product's manufacturer as they may cause hazards.
7. WATER AND MOISTURE
Do not use this product near water–for example: near a bathtub, washbowl, kitchen sink or laundry tub; in
a wet basement; or near a swimming pool.
8. ACCESSORIES
Do not place this product on an unstable cart, stand, tripod, bracket or table. The product may fall, causing
serious injury and serious damage to the product. Use only with a cart, stand, tripod, bracket or table rec-
ommended by the manufacturer or sold with the product. Any mounting of the product
PORTABLE CART WARNING
should follow the manufacturer’s instructions, and should use a mounting accessory rec-
(symbol provided by RETAC)
ommended by the manufacturer.
8A. An appliance and cart combination should be moved with care. Quick stops, excessive
force and uneven surfaces may cause the appliance and cart combination to overturn.
9. VENTILATION
Slots and openings in the cabinet and in the back or bottom are provided for ventilation,
to ensure reliable operation of the product and to protect it from overheating. These
openings must not be blocked or covered. The openings should never be blocked by
placing the product on a bed, sofa, rug or other similar surface. This product should never be placed near
or over a radiator or heat source. This product should not be placed in a built-in installation such as a
bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been
adhered to.
10. POWER SOURCES
This product should be operated only from the type of power source indicated on the marking label. If you
are not sure of the type of power supply to your home, consult your appliance dealer or local power com-
pany. For products intended to operate from battery power, or other sources, refer to the operating instruc-
tions.
11. GROUNDING OR POLARIZATION
This product is equipped with a polarized alternating-current line plug (a plug having one blade wider than
the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to
insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your elec-
trician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.
12. POWER-CORD PROTECTION
Power-supply cords should be routed so that they are not likely to be walked on or pinched by items
placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and
the point where they exit from the appliance.
13. LIGHTNING
To protect your product from a lightning storm, or when it is left unattended and unused for long periods of
time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage
to the product due to lightning and power-line surges.
14. POWER LINES
An outside antenna system should not be located in the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall into such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep from touching such power lines or circuits as con-
tact with them might be fatal.
Download from Www.Somanuals.com4. All Manuals Search And Download.
SAFETY INSTRUCTIONS (CONTINUED)
15. OVERLOADING
Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.
16. OBJECT AND LIQUID ENTRY
Never push objects of any kind into this product through openings as they may touch dangerous voltage points
or short out parts that could result in fire or electric shock. Never spill or spray any type of liquid on the product.
17. OUTDOOR ANTENNA GROUNDING
If an outside antenna is connect-
ed to the product, be sure the
antenna system is grounded so
ANTENNA
LEAD IN
WIRE
as to provide some protection
against voltage surges and built-
GROUND
CLAMP
up static charges. Section 810 of
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
the National Electric Code,
ANSI/NFPA 70, provides informa-
tion with respect to proper
grounding of the mast and sup-
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
porting structure, grounding of the
lead-in wire to an antenna dis-
charge product, size of grounding
conductors, location of antenna
discharge product, connection to
grounding electrodes and require-
ments for grounding electrode.
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC - NATIONAL ELECTRICAL CODE
S2898A
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
18. SERVICING
Do not attempt to service this product yourself as opening or removing covers may expose you to danger-
ous voltage or other hazards. Refer all servicing to qualified service personnel.
19. REPLACEMENT PARTS
When replacement parts are required, be sure the service technician uses replacement parts specified by
the manufacturer or those that have the same characteristics as the original part. Unauthorized substitu-
tions may result in fire, electric shock or other hazards.
20. SAFETY CHECK
Upon completion of any service or repairs to this product, ask the service technician to perform safety
checks to determine that the product is in proper operating condition.
21. WALL OR CEILING MOUNTING
The product should be mounted to a wall or ceiling only as recommended by the manufacturer.
22. DAMAGE REQUIRING SERVICE
Unplug the product from the wall outlet and refer servicing to qualified service personnel under the follow-
ing conditions:
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled or objects have fallen into the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the
operating instructions, as an adjustment of other controls may result
in damage and will often require extensive work by a qualified
technician to restore the product to its normal operation.
e. If the product has been dropped or the cabinet has been damaged.
f.
When the product exhibits a distinct change in performance–this
indicates a need for service.
23. HEAT
The product should be situated away from heat sources such as radiators, heat registers, stoves or other
products (including amplifiers) that produce heat.
24. NOTE TO CATV SYSTEM INSTALLER
This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be con-
nected to the grounding system of the building, as close to the point of cable entry as practical.
Download from Www.Somanuals.com5. All Manuals Search And Download.
LOCATION OF CONTROLS
1
2
3
4 5
6
7 8 9 1011
12
13
14
1516
17 1819
1. FM Antenna
2. CD Compartment
12. Left Carrying Handle
13. Display
3. CD Door Open/Close Area
4. TUNER/BAND button
5. POWER Button
6. AC Power Jack (Rear of Unit)
7. VOLUME Buttons
14. Battery Compartment (Bottom
of Unit)
15. PROG/CH SAVE Button
16. CH+/MODE Button
17. Right Carrying Handle
18. STOP (I) Button
19. Tune/Skip/Search o Button
8. PHONES (Headphones) Jack
(Side of Unit)
9. EQ Button
10. Tune/Skip/Search n Button
11. PLAY/PAUSE (®p)/CD Button
Download from Www.Somanuals.com6. All Manuals Search And Download.
POWER SOURCES
This unit is designed to operate on AC household current or DC (batteries).
AC
Use the AC polarized line cord included with the unit for operation on AC power.
Insert one end of the AC line cord into the AC power jack on the rear of the unit
and the other end (with the 2 blades) into a conve-
niently located AC outlet having 120V, 60Hz.
When the AC cord is plugged in, the batteries will
AC Outlet
be disconnected.
NOTE: The AC plug supplied with the unit is polar-
ized to help minimize the possibility of electric
shock. If the AC plug does not fit into a nonpolar-
AC Plug
ized AC outlet, do not file or cut the wide blade. It is the user’s responsibility to have
an electrician replace the obsolete outlet.
BATTERY INSTALLATION
To use this unit with battery power,
remove the battery door on the
bottom of the unit by sliding the
battery door off. Insert eight (8) ‘C’
size batteries following the diagram
in the compartment.
NOTE: The AC power cord must be
disconnected from the AC power jack
on the rear of the unit in order for the
unit to operate on battery power.
BATTERY PRECAUTIONS
Follow these precautions when using batteries in this device:
1. Use only the size and type of batteries specified.
2. Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment.
Reversed batteries may cause damage to the device.
3. Do not mix different types of batteries together (e.g. Alkaline, Rechargeable and Carbon-zinc) or old batter-
ies with fresh ones.
4. If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from
possible battery leakage.
5. Do not try to recharge batteries not intended to be recharged; they can overheat and rupture. (Follow battery
manufacturer’s directions.)
HEADPHONE JACK (SIDE OF UNIT)
For private listening, connect 3.5mm (32 ohm) stereo headphones (not included) to this
jack. The speakers are automatically disconnected when the headphone plug is inserted in
the jack.
Download from Www.Somanuals.com7. All Manuals Search And Download.
OPERATION
LISTENING TO THE RADIO
1
2
Press the TUNER/BAND button to
select radio. Repeatedly press the
TUNER/BAND button to select AM or
FM. If a stereo station is broadcast,
“ST” will appear.
Press the POWER button to turn the
unit on.
3
4
2
2
1
1
AUTOMATIC TUNING: Press and hold the
MANUAL TUNING: Repeatedly press
the Tune/Skip/Search o 1 or n 2 but-
ton to manually advance the frequen-
cy in the display up or down until the
desired frequency appears.
Tune/Skip/Search o 1 or n 2 button until
the frequency in the display starts to scan,
and then release the button; the tuner will
search and then stop on the next strong
station it finds. Repeat this step until the
desired frequency appears in the display.
5
6
2
1
Adjust the VOLUME buttons 1 and
EQ button 2 as desired. Repeatedly
press the EQ button 2 to cycle
through the EQ settings as follows:
ROCK, JAZZ, POP, CLASSICAL.
To turn the radio off, press the
POWER button again.
ANTENNAS
AM–This unit has a built-in ferrite rod antenna, which provides adequate reception in most
areas. If reception is weak, turn the unit to improve reception.
FM–The FM Antenna is for FM reception only. If reception is weak, adjust the length and the
angle of the antenna.
Download from Www.Somanuals.com. All Manuals Search And Download.
8
OPERATION (CONTINUED)
SETTING AND RECALLING RADIO PRESETS
This unit can preset 12 AM and 20 FM radio stations for convenient recall.
1
2
Press the POWER button to turn the
unit on.
Press the TUNER/BAND button to
select radio. Repeatedly press the
TUNER/BAND button to select AM or
FM.
3
4
2
1
2
1
Select a station using the Tune/Skip/
Search o 1 or n 2 button. (See the
previous page for manual or auto
tuning.)
Press the PROG/CH SAVE button 1;
“PRESET” will appear and the number
will blink in the display. Press the
MODE/CH+ button 2 until the desired
memory number appears on the dis-
play.
5
6
Press the PROG/CH SAVE button again
to set the station in the selected memo-
ry. Repeat steps 3 through 5 to program
up to 20 stations for FM and 12 stations
for AM, if desired.
TO RECALL: Follow steps 1 and 2
above. Repeatedly press the
MODE/CH+ button to select a preset;
the station will automatically be tuned
in.
Download from Www.Somanuals.com9. All Manuals Search And Download.
OPERATION (CONTINUED)
TO PLAY A CD
1
2
1
2
Press the POWER button 1 to turn the
unit on. Open the CD compartment door
by pressing the OPEN/CLOSE area 2.
Place a CD on the center spindle, with
the printed label side facing up. Close
the CD compartment door.
Press the PLAY/PAUSE (®p)/CD
button to select CD; playback will
start automatically.
3
4
2
1
Adjust the VOLUME buttons 1 and EQ
Press the PLAY/PAUSE (¨/p)/CD but-
ton again to pause playback; the time
button 2 as desired. Repeatedly press the
EQ button 2 to cycle through the EQ set-
tings as follows: ROCK, JAZZ, POP,
CLASSICAL.
display
will
blink.
Press
the
PLAY/PAUSE (¨/p)/CD button once
again to continue playback; the time dis-
play will stop blinking.
5
6
2
1
2
1
To search forward or backward through
the music on a disc, press and hold the
Tune/Skip/Search o 1 or n 2 button, a
chattering noise will be heard.
To skip forward or backward through
the tracks on the disc, press the
Tune/Skip/Search o 1 or n 2 button.
CONTINUED ON THE NEXT PAGE
Download from Www.Somanuals.co1m0. All Manuals Search And Download.
OPERATION (CONTINUED)
TO PLAY A CD (CONTINUED)
7
8
When the disc is through playing, it will
stop rotating. Press the STOP (I) but-
ton to stop the disc before it is finished.
To turn the unit off, press the POWER
button again.
NOTES:
• If a disc is inserted incorrectly, dirty or damaged, it will not play.
• As each track is played, the track number is shown in the display.
• To prevent damage to the disc, never open the CD door while the disc is rotat-
ing. Wait for the disc to stop before opening the CD door. Never touch the lens
when the CD door is open.
• DO NOT use the carrying handles when playing a CD. The CD should only
be used on a steady surface.
TO REPEATEDLY PLAY BACK ONE TRACK/ALL TRACKS
1
2
1
3
2
To repeat a single track, press the
MODE/CH+ button 1 once while in
the Playback mode; “REPEAT 1” will
light in the display. Press the
Tune/Skip/Search o 2 or n 3 button
to select the specific track that you
wish to repeat. The specific track you
To repeat all of the tracks on a disc
continuously, press the MODE/CH+
button twice while in the Playback
mode; “REPEAT ALL” will light. All
tracks will be repeated continuously.
selected
will
be
repeated
continuously.
To stop and cancel Repeat playback, press the STOP (I) button.
Download from Www.Somanuals.com. All Manuals Search And Download.
11
OPERATION (CONTINUED)
TO PROGRAM THE MEMORY (UP TO 20 TRACKS)
1
2
2
1
With the power on and the unit in the
Stop mode, press the PROG/CH
SAVE button; “PROG”, “P01”
(Program Number) and “00” (Track
Number) will appear in the display.
Use the Tune/Skip/Search o 1 or n 2
button to select the first track to be
programmed.
3
4
2
1
Press the PROG/CH SAVE button
again; the selected track has now
been programmed and counted as
program 1.
Repeat steps 2 and 3 to program the
other desired tracks in sequence.
5
Press the PLAY/PAUSE (¨/p)/CD
button to begin playback; “PROG” will
light and the tracks will play in the
order programmed.
SEE NEXT PAGES FOR NOTES ON PROGRAMMED PLAY
Download from Www.Somanuals.co1m2. All Manuals Search And Download.
OPERATION (CONTINUED)
NOTES ON PROGRAMMED PLAY:
•
Programming is the ability to preselect the order in which a series of tracks
will be played.
•
•
Each track may be stored in the program memory as many times as desired.
As each track is played, its track number will be displayed. You can move for-
ward or backward through the programmed tracks with the Tune/Skip/
Search o or n button.
•
•
•
The CD player will stop after all programmed tracks have been played or the
STOP (I) button is pressed.
To stop Program playback, press the STOP (I) button. To play back the pro-
gram again, press the PLAY/PAUSE (¨/p)/CD button.
To clear the program memories, while in the Stop mode, press the STOP (I)
button; the PROG indicator will disappear from the display.
PROGRAMMED REPEAT
1
2
It is also possible to use the Program and
Repeat functions together to repeat a
specific program indefinitely. First,
program the tracks you wish to hear in the
order you wish to hear them, as described
on page 12. Press the PLAY/PAUSE
(¨/p)/CD button to begin programmed
playback.
Then, press the MODE/CH+ button twice.
Both the “PROG” and “REPEAT”
indicators will light. The player will
repeatedly play back the tracks you
selected in the order in which you
programmed them. When the last
track in the program has been played,
the entire program will begin again.
NOTE:
Program Repeat operation will continue indefinitely until you press the STOP (I)
button.
Download from Www.Somanuals.co1m3. All Manuals Search And Download.
OPERATION (CONTINUED)
TO RANDOMLY PLAY A CD
1
2
1
2
The unit will randomly play the tracks
on the CD and then stop. Press the
STOP (I) button to stop Random
playback before it is finished.
Press the MODE/CH+ button 1 once
while in the Stop mode; “RANDOM”
will light. Press the PLAY/PAUSE
(¨/p)/CD button 2 to begin playback.
INTRO PLAYBACK
1
2
1
2
The unit will play the first 10 seconds
of each track on the CD and then stop.
Press the STOP (I) button to stop
Intro playback before it is finished.
Press the MODE/CH+ button 1 twice
while in the Stop mode; “INTRO” will
light. Press the PLAY/PAUSE
(¨/p)/CD button 2 to begin playback.
Download from Www.Somanuals.co1m4. All Manuals Search And Download.
CARE AND MAINTENANCE
Caring for Compact Discs
• Treat the compact disc carefully. Handle the com-
pact disc only by its edges. Never allow your
fingers to come in contact with the shiny, unprint-
ed side of the compact disc.
• Do not attach adhesive tape, stickers, etc. to
the disc label.
• Clean the compact disc periodically with a soft, lint-free, dry cloth. Never use deter-
gents or abrasive cleaners to clean the compact disc. If necessary, use a CD clean-
ing kit.
• If a disc skips or gets stuck on a sec-
tion of the compact disc, it is probably
dirty or damaged (scratched).
• When cleaning the compact disc,
wipe in straight lines from the center
Z
of the compact disc to the outer edge
of the compact disc. Never wipe in
circular motions.
• This unit is designed to play only compact discs bearing the identifica-
tion logo as shown here. Other discs may not conform to the CD stan-
dard and may not play properly.
• Compact discs should be stored in their cases after each use to avoid damage.
• Do not expose compact discs to direct sunlight, high humidity, high temperatures or
dust, etc. Prolonged exposure or extreme temperatures can warp the compact disc.
• Do not stick or write anything on either side of the compact disc. Sharp writing
instruments, or the ink, may damage the surface.
Cleaning the Unit
• To prevent fire or shock hazard, disconnect your unit from the AC power source
when cleaning.
• The finish on your unit may be cleaned with a dust cloth and cared for as other fur-
niture. Use caution when cleaning and wiping the plastic parts.
• Mild soap and a damp cloth may be used on the front panel.
Download from Www.Somanuals.co1m5. All Manuals Search And Download.
TROUBLESHOOTING GUIDE
If you experience a problem with this unit, check the chart below before calling for
service.
SYMPTOM
Unit will not
CAUSE
AC cord not
connected.
SOLUTION
Check AC cord
connection.
turn on.
Disc will not play.
CD compartment
door not closed.
Disc inserted
incorrectly.
Close CD compartment
door.
Reinsert disc correctly.
Dirty or defective CD. Try another disc.
Moisture
Wipe disc with soft cloth.
condensation on disc.
VOLUME buttons
set to minimum.
Defective disc.
Dirty or defective
disc.
No sound.
Increase volume.
Try another disc.
Erratic playback.
Clean or replace disc.
AM or FM, no sound. Power is not on.
VOLUME is set
Press the POWER button.
Increase volume.
to minimum.
AM/FM, poor sound. Station is not tuned
properly.
Retune the AM or FM
broadcast station.
Reorient FM telescopic
antenna.
FM: Telescopic ant-
antenna is not
properly adjusted
AM: Unit is not pos-
itioned correctly.
Rotate unit until best
reception is obtained.
Download from Www.Somanuals.co1m6. All Manuals Search And Download.
SPECIFICATIONS
GENERAL:
Power Source ..............................................................................120V, 60Hz AC
Battery.........................................................12V DC (8 x 1.5V ‘C’ size batteries)
Alkaline is recommended for longer life
Speaker.....................................................................................................2 x 3W
Output Power .........................................................................................2 x 1.8W
RADIO SECTION:
Frequency Range (FM) ...............................................................87.5 - 108 MHz
Frequency Range (AM) ...............................................................520 -1710 KHz
CD SECTION:
Disc Diameter ...............................................................................4.72" (120mm)
3.15" (80mm) Single
CD
Optical Source....................................................................Semiconductor Laser
Specifications are subject to change without notice.
FOR ADDITIONAL SET-UP OR OPERATING ASSISTANCE, PLEASE VISIT
OUR WEBSITE AT WWW.MEMOREXELECTRONICS.COM OR CONTACT
CUSTOMER SERVICE AT
1-800-919-3647.
PLEASE KEEP ALL PACKAGING MATERIAL FOR AT LEAST 90 DAYS IN
CASE YOU NEED TO RETURN THIS PRODUCT TO YOUR PLACE OF PUR-
CHASE OR MEMOREX.
FOR PARTS AND ACCESSORIES, CONTACT FOX INTERNATIONAL AT
1-800-321-6993.
Download from Www.Somanuals.com. All Manuals Search And Download.
17
Memcorp, Inc.
Weston, FL
Printed in Hong Kong
Download from Www.Somanuals.com. All Manuals Search And Download.
|