MC900
Operator's Manual / 96083000400 / 2009-11
532 43 21-09
Download from Www.Somanuals.com. All Manuals Search And Download.
CUSTOMER RESPONSIBILITIES
PRODUCT SPECIFICATIONS
•
•
Read and observe the safety rules.
Gasoline Capacity:
Unleaded Regular
3 Quarts (2.8L)
Follow a regular schedule in maintaining, caring for
and using your tiller.
Oil (API-SG-SL):
(Capacity: 16 oz./0.47 L)
SAE30(Above32°F)
SAE 5W-30 (Below 32°F)
•
Followinstructionsunder“Maintenance”and“Storage”
sections of this Manual.
Spark Plug :
(Gap: .030"/0.76mm)
NGK-BPR6ES
TORCH-F6RTC
IMPORTANT: THIS UNIT IS EQUIPPED WITH AN INTERNAL
COMBUSTION ENGINE AND SHOULD NOT BE USED ON
OR NEAR ANY UNIMPROVED FOREST-COVERED, BRUSH-
COVERED OR GRASS COVERED LAND UNLESS THE
ENGINE'S EXHAUST SYSTEM IS EQUIPPED WITH A SPARK
ARRESTER MEETING APPLICABLE LOCAL LAWS (IF ANY).
IFASPARKARRESTERISUSED,ITSHOULDBEMAINTAINED
IN EFFECTIVE WORKING ORDER BY THE OPERATOR.
CONGRATULATIONS on your purchase of a new tiller. It
has been designed, engineered and manufactured to give
you the best possible dependability and performance.
Should you experience any problems you cannot easily
remedy, please contact your nearest authorized service
center. We have competent, well-trained technicians and
the proper tools to service or repair this unit.
IN THE STATE OF CALIFORNIA, A SPARK ARRESTER IS
REQUIRED BY LAW (SECTION 4442 OF THE CALIFORNIA
PUBLIC RESOURCES CODE). OTHER STATES MAY HAVE
SIMILARLAWS. FEDERALLAWSAPPLYONFEDERALLANDS.
SEE YOUR AUTHORIZED SERVICE CENTER/DEPARTMENT
FOR SPARK ARRESTER.
Please read and retain this manual. The instructions will
enable you to assemble and maintain your tiller properly.
Always observe the “SAFETY RULES”.
TABLE OF CONTENTS
MAINTENANCE .....................................................10-12
SERVICE & ADJUSTMENTS .................................12-14
STORAGE.................................................................... 15
TROUBLESHOOTING................................................. 16
WARRANTY................................................BACK PAGE
SAFETY RULES ............................................................ 2
PRODUCT SPECIFICATIONS....................................... 3
CUSTOMER RESPONSIBILITIES................................. 3
ASSEMBLY.................................................................4-5
OPERATION ...............................................................6-9
MAINTENANCE SCHEDULE ...................................... 10
3
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Your new tiller has been assembled at the factory with exception of those parts left unassembled for shipping purposes.
To ensure safe and proper operation of your tiller all parts and hardware you assemble must be tightened securely. Use
the correct tools as necessary to insure proper tightness.
TOOLS REQUIRED FOR ASSEMBLY
A socket wrench set will make assembly easier. Standard
wrench sizes are listed.
FRONT
(1) Utility knife
(2) 1/2" wrenches
LEFT
RIGHT
OPERATOR’S POSITION (See Fig. 1)
When right or left hand is mentioned in this manual, it
means when you are in the operating position (standing
behind tiller handles).
OPERATOR'S POSITION
Fig. 1
CONTENTS OF HARDWARE PACK
(2) Carriage Bolts
5/16-18 UNC x 2-1/2
(2) Flange
Locknuts
5/16-18 UNC
(1) Manual
(2) Hex Bolt
5/16-18 x 1-1/4
(2) Hex Nut
5/16-18
(2) Lock
Washer
5/16
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
UNPACK CARTON & INSTALL HANDLE
(See Fig. 2)
INSTALL DEPTH STAKE ASSEMBLY
(See Fig. 3)
•
•
Loosen nut “A”.
CAUTION: Be careful of exposed
staples when handling or disposing
of cartoning material.
Insert stake support between engine bracket halves
with stake spring down.
•
•
Bolt stake support to engine brackets with bolts, lock
washers and nuts. Tighten securely. Tighten nut “A”.
Depth stake must move freely. If it does not, loosen
support bolt.
IMPORTANT:
WHEN UNPACKING AND ASSEMBLING
TILLER, BE CAREFUL NOT TO STRETCH OR KINK
CABLE(S).
•
Cut cable ties securing handle column.
•. Routecable(s)asshownandslidehandlecolumnonto
ENGINE BRACKET
HALVES
handle mount.
•
•
Remove all packing from carton.
Secure handle column using two (2) carriage bolts and
two (2) flange locknuts. Tighten securely.
NUT “A”
DEPTH
STAKE
DEPTH STAKE
SUPPORT
•
•
Cut away carton.
Route tine control cable(s) through plastic cable clip
on handle mount.
NOTE: Cables must not touch the muffler.
•
Cut cable ties securing tiller to skid. Remove tiller from
skid by pulling backwards.
•
Remove screws securing depth stake to skid and
discard the screws.
SUPPORT
BOLT
STAKE
SPRING
HANDLE
PANEL
BOLTS
HEX BOLTS,
LOCK WASHERS,
AND HEX NUTS
Fig. 3
CABLE(S)
HANDLE HEIGHT
•
Handle height may be adjusted to better suit operator.
(See “HANDLE HEIGHT” in the Service and Adjust-
ments section of this manual).
TILLER
HANDLES
TILLING WIDTH
•
Tilling width may be adjusted to better handle your
tilling conditions (See “TINE ARRANGEMENT” in the
Service and Adjustments section of this manual).
TINE OPERATION
•
Check tine operation before first use. (See “TINE OP-
ERATION CHECK” in the Service and Adjustments
section of this manual).
Fig. 2
5
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
KNOW YOUR TILLER
READ THIS MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TILLER.
Compare the illustrations with your tiller to familiarize yourself with the location of various controls and adjustments. Save
this manual for future reference.
These symbols may appear on your Tiller or in literature supplied with the product. Learn and understand their mean-
ing.
Forward Tine
Control
Fuel Fill Port
Throttle Control
Fuel Valve
Choke Control
Depth
Stake
On/Off Switch
Recoil Starter
Handle
Tines
Fig. 4
MEETS ANSI SAFETY REQUIREMENTS
Our tillers conform to the safety standards of the American National Standards Institute.
CHOKE CONTROL - Used when starting a cold engine.
DEPTH STAKE - Controls forward speed and the depth
at which tiller will dig.
ENGINE ON/OFF SWITCH - The engine switch enables
and disables the ignition system.
FUEL VALVE - The fuel valve opens and closes the pas-
sage between the fuel tank and the carburetor.
RECOIL STARTER HANDLE - Used to start the engine.
THROTTLE CONTROL - Used to control engine speed.
FORWARD TINE CONTROL - Engages tines in forward
direction.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
The operation of any tiller can result in foreign objects thrown into the eyes, which can result
in severe eye damage. Always wear safety glasses or eye shields before starting your tiller
and while tilling. We recommend a wide vision safety mask for over spectacles or standard
safety glasses.
TILLING
HOW TO USE YOUR TILLER
Know how to operate all controls before adding fuel and oil
or attempting to start engine.
The speed and depth of tilling is regulated by the position
of the depth stake and wheel height.
The depth stake should always be below the wheels for
digging. It serves as a brake to slow the tiller’s forward
motion to enable the tines to penetrate the ground. Also,
the more the depth stake is lowered into the ground the
deeper the tines will dig.
STOPPING (See Fig. 5)
TINES
1. Release tine control to stop movement.
ENGINE
DEPTH STAKE (See Fig. 6)
2. Move throttle control to “SLOW” position and allow the
engine to run slowly for cool down.
Adjust depth stake by removing the hairpin clip and clevis
pin. Change depth stake to desired position. Replace the
clevis pin and hairpin clip.
3. Turn the engine switch to the "OFF" Position.
4. Turn the fuel valve lever to the "OFF" Position.
NOTE: NEVER USE CHOKE TO STOP ENGINE.
•
For normal tilling, set depth stake at the second or third
hole from the top.
IMPORTANT: TO STOP ENGINE IN AN EMERGENCY, TURN
THE ENGINE SWITCH TO THE OFF POSITION.
WHEELS (See Fig. 6)
Adjust wheels by removing the hairpin clip and clevis pin.
Change wheel position. Replace the hairpin clip and clevis
pin.
Tine Control
“Off” (UP) Position
•
For normal tilling, set wheels at the second or third
hole from the top.
HAIRPIN CLIP
AND CLEVIS PIN
Tine Control
“On” (DOWN) Position
Fuel Valve
Throttle
Control
Engine
Switch
1
DEPTH
STAKE
Throttle
Control
STAKE
SPRING
WHEEL
Fig. 6
Fuel
Valve
Engine
Switch
Fig. 5
TINE OPERATION (See Fig. 6)
FORWARD
•
Squeeze forward tine control to handle.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
TO TRANSPORT
CAUTION: Fill to within 1/2 inch of top
offueltanktopreventspillsandtoallow
for fuel expansion. If gasoline is ac-
cidentally spilled, move machine away
from area of spill. Avoid creating any
sourceofignitionuntilgasolinevapors
have disappeared.
CAUTION: Beforeliftingortransporting,
allow tiller engine and muffler to cool.
Disconnect spark plug wire. Drain
gasoline from fuel tank.
AROUND THE YARD
Wipe off any spilled oil or fuel. Do not
store, spill or use gasoline near an
open flame.
•
Tip depth stake forward until it is held by the stake
spring.
•
•
Push tiller handles down, raising tines off the ground.
Push or pull tiller to desired location.
IMPORTANT: WHEN OPERATING IN TEMPERATURES
BELOW32°F(0°C), USE FRESH, CLEAN WINTER GRADE
GASOLINE TO HELP INSURE GOOD COLD WEATHER
STARTING.
AROUND TOWN
•
•
•
Disconnect spark plug wire.
Drain fuel tank.
Transport in upright position to prevent oil leakage.
CAUTION: Alcohol blended fuels (called
gasohol or using ethanol or methanol) can at-
tract moisture which leads to separation and
formation of acids during storage. Acidic gas
can damage the fuel system of an engine while
in storage. To avoid engine problems, the fuel
system should be emptied before storage of
30 days or longer. Drain the gas tank, start
the engine and let it run until the fuel lines
and carburetor are empty. Use fresh fuel next
season. SeeStorageInstructionsforadditional
information. Never use engine or carburetor
cleaner products in the fuel tank or permanent
damage may occur.
BEFORE STARTING ENGINE
IMPORTANT: BE VERY CAREFUL NOT TO ALLOW DIRT
TO ENTER THE ENGINE WHEN CHECKING OR ADDING
OIL OR FUEL. USE CLEAN OIL AND FUEL AND STORE IN
APPROVED, CLEAN, COVERED CONTAINERS. USE CLEAN
FILL FUNNELS.
FILL ENGINE WITH OIL (See Fig. 7)
•
•
With engine level, remove engine oil filler plug.
Fill engine with oil to point of overflowing. For approx-
imatecapacitysee“PRODUCTSPECIFICATIONS”on
page 3 of this manual.
Tilt tiller back on its wheels and then re-level.
With engine level, refill to point of overflowing if nec-
essary. Replace oil filler plug.
TO START ENGINE (See Fig. 8)
•
•
CAUTION: KEEP TINE CONTROL IN “OFF”
POSITION WHEN STARTING ENGINE.
•
•
For cold weather operation you should change oil for
easier starting (See “OIL VISCOSITY CHART” in the
Maintenance section of this manual).
To change engine oil, see the Maintenance section of
this manual.
When starting engine for the first time or if engine has run
out of fuel, it will take extra pulls of the recoil starter to
move fuel from the tank to the engine.
1. Make sure spark plug wire is properly connected.
2. Place the fuel valve to the "ON" position.
3. To start a cold engine, move the choke lever to the
Oil Filler
Plug
Oil Level
"ON" position.
4. Movethethrottleleverawayfromthe"SLOW"position,
about 1/3 of the way toward the "FAST" position.
5. Turn the engine switch to the "ON" position. Pull rope
out slowly until engine reaches start of compression
cycle (rope will pull slightly harder at this point).
4
_
rt
_a
ne
i
ng
e
Max Upper Level
Min Lower Level
6. Pull recoil starter handle quickly. Do not let starter
handle snap back against starter. Repeat if neces-
sary.
NOTE: IF ENGINE FIRES BUT DOES NOT START, MOVE
CHOKECONTROLTOHALFCHOKEPOSITION.PULLRECOIL
STARTER HANDLE UNTIL ENGINE STARTS.
7. If the choke lever has been moved to the "ON" position
to start the engine, gradually move it to the opposite
position as the engine warms up.
NOTE: A WARM ENGINE REQUIRES LESS CHOKING TO
START.
Fig. 7
ADD GASOLINE
•
Fill fuel tank to bottom of filler neck. Do not overfill.
Use fresh, clean, regular unleaded gasoline with a
minimum of 87 octane. (Use of leaded gasoline will
increase carbon and lead oxide deposits and reduce
valve life). Do not mix oil with gasoline. Purchase fuel
in quantities that can be used within 30 days to assure
fuel freshness.
8. Move throttle control to desired running position.
9. Allow engine to warm up for a few minutes before
engaging tines.
NOTE: IFENGINEDOESNOTSTART,SEE TROUBLESHOOTING
POINTS.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
Fuel Valve
•
Soilconditionsareimportantforpropertilling.Tineswill
notreadilypenetratedry,hardsoilwhichmaycontribute
to excessive bounce and difficult handling of your tiller.
Hard soil should be moistened before tilling; however,
extremely wet soil will “ball-up” or clump during tilling.
Wait until the soil is less wet in order to achieve the
best results. When tilling in the fall, remove vines and
long grass to prevent them from wrapping around the
tine shaft and slowing your tilling operation.
Spark Plug
Throttle Control
Choke
Control
•
•
You will find tilling much easier if you leave a row un-
tilled between passes. Then go back between tilled
rows. (See Fig. 9) There are two reasons for doing
this. First, wide turns are much easier to negotiate than
about-faces. Second, the tiller won’t be pulling itself,
and you, toward the row next to it.
Set depth stake and wheel height for shallow tilling
when working extremely hard soil or sod. Then work
across the first cuts at normal depth.
Recoil Starter
Engine
Switch
Fuel Valve
Spark Plug
Throttle Control
Choke
Control
Recoil Starter
Engine
Switch
4
3
2
1
Fig. 8
5
6
7
BREAKING IN YOUR TILLER
Break-in your belt(s), pulleys and tine control before you
actually begin tilling.
•
•
Start engine, tip tines off ground by pressing handles
down and engage tine control to start tine rotation.
Allow tines to rotate for five minutes.
Checktineoperationandadjustifnecessary. See“TINE
OPERATION CHECK” in the Service and Adjustments
section of this manual.
Fig. 9
CULTIVATING
Cultivating is destroying the weeds between rows to pre-
vent them from robbing nourishment and moisture from the
plants. At the same time, breaking up the upper layer of
soil crust will help retain moisture in the soil. Best digging
depth is 1"-3".
TILLING HINTS
•
Youwillprobablynotneedtousethedepthstake.Begin
by tipping the depth stake forward until it is held by the
stake spring.
CAUTION: Until you are accustomed
to handling your tiller, start actual field
use with throttle in slow position.
•
Cultivate up and down the rows at a speed which will
allow tines to uproot weeds and leave the ground in
rough condition, promoting no further growth of weeds
and grass (See Fig. 10).
To help tiller move forward, lift up the handles slightly (thus
lifting depth stake out of ground). To slow down the tiller,
press down on handles.
If you are straining or tiller is shaking, the wheels and depth
stakearenot setproperlyinthesoilbeingtilled. Theproper
setting of the wheels and depth stake is through trial and
error and depends upon the soil condition. (The harder or
wetter the ground, the slower the engine and tine speed
needed. Under these poor conditions, at fast speed the
tiller will run and jump over the ground).
A properly adjusted tiller will dig with little effort from the
operator.
•
Tilling is digging into, turning over, and breaking up
packedsoilbeforeplanting. Loose,unpackedsoilhelps
root growth. Best tilling depth is 4"-6". A tiller will also
clearthesoilofunwantedvegetation.Thedecomposition
of this vegetable matter enriches the soil. Depending
on the climate (rainfall and wind), it may be advisable
to till the soil at the end of the growing season to further
condition the soil.
Fig. 10
9
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
MAINTENANCE
SCHEDULE
FILL IN DATES
AS YOU COMPLETE
REGULAR SERVICE
SERVICE DATES
BEFORE EEAVCEHRUYS5EHEOVEURYS 25EHVOEURRYS50 HOURS
Check Engine Oil Level
Change Engine Oil
Oil Pivot Points
Inspect Spark Arrester / Muffler
Inspect Air Screen
Clean or Replace Air Cleaner Cartridge
Clean Engine Cylinder Fins
Replace Spark Plug
2
1 - Change more often when operating under a heavy load or in high ambient temperatures.
2 - Service more often when operating in dirty or dusty conditions.
LUBRICATION CHART
GENERAL RECOMMENDATIONS
c TINE CONTROL
The warranty on this tiller does not cover items that have
beensubjectedtooperatorabuseornegligence. Toreceive
fullvaluefromthewarranty,theoperatormustmaintaintiller
as instructed in this manual.
Some adjustments will need to be made periodically to
properly maintain your tiller.
d ENGINE
At least once a season, check to see if you should make
any of the adjustments described in the Service and Ad-
justments section of this manual.
•
Once a year you should replace the spark plug, clean
or replace air filter, and check tines and belts for wear.
A new spark plug and clean air filter assure proper
air-fuel mixture and help your engine run better and
last longer.
BEFORE EACH USE
•
•
•
Check engine oil level.
Check tine operation.
Check for loose fasteners.
c IDLER
ARM
LUBRICATION
Keep unit well lubricated (See “LUBRICATION CHART”).
cSAE 30 OR 10W-30 MOTOR OIL
dREFER TO MAINTENANCE “ENGINE” SECTION
10
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Disconnect spark plug wire before performing any maintenance (except carburetor adjustment) to
prevent accidental starting of engine.
Prevent fires! Keep the engine free of grass, leaves, spilled oil, or fuel. Remove fuel from tank
before tipping unit for maintenance. Clean muffler area of all grass, dirt, and debris.
Do not touch hot muffler or cylinder fins as contact may cause burns.
ENGINE
LUBRICATION
Use only high quality detergent oil rated with API service
classification SG-SL. Select the oil’s SAE viscosity grade
according to your expected temperature.
OIL
DRAIN
PLUG
ªªªªªªªªªªªªªªªªªªªªªªªªªªªªªªªªªªªª3!%ª6)3#/3)49ª'2!$%3
OIL LEVEL
OIL FILLER
PLUG
Fig. 12
AIR CLEANER (See Fig. 13)
Service aircleanercartridgeeverytwenty-fivehours, more
often if engine is used in very dusty conditions.
4%-0%2!452%ª2!.'%ª!.4)#)0!4%$ª"%&/2%ª.%84ª/),ª#(!.'%
•
Loosen air cleaner screws, one on each side of
cover.
Fig. 11
•
•
Remove air cleaner cover.
NOTE: Althoughmulti-viscosityoils(5W-30, 10W-30, etc.)
improve starting in cold weather, these multi viscosity oils
will result in increased oil consumption when used above
32°F (0°C). Check your engine oil level more frequently to
avoid possible engine damage from running low on oil.
Change the oil after every 25 hours of operation or at least
once a year if the tiller is not used for 25 hours in one year.
Check the crankcase oil level before starting the engine
and after each five (5) hours of continuous use. Add SAE
30 motor oil or equivalent. Tighten oil filler plug securely
each time you check the oil level.
Carefully remove air cleaner cartridge. Be careful. Do
not allow dirt or debris to fall into carburetor.
Clean by tapping gently on a flat surface.
If very dirty or damaged, replace cartridge.
Clean and replace cover. Tighten screws securely.
•
•
•
IMPORTANT: PETROLEUMSOLVENTS,SUCHASKEROSENE,
ARE NOT TO BE USED TO CLEAN THE CARTRIDGE. THEY
MAY CAUSE DETERIORATION OF THE CARTRIDGE. DO
NOT OIL CARTRIDGE. DO NOT USE PRESSURIZED AIR TO
CLEAN OR DRY CARTRIDGE.
Air Cleaner
Cartridge
TO CHANGE ENGINE OIL (See Figs. 11 and 12)
Determine temperature range expected before oil change.
All oil must meet API service classification SG-SL.
Pre-Cleaner
Cover
•
•
•
•
•
•
Be sure tiller is on level surface.
Oil will drain more freely when warm.
Catch oil in a suitable container.
Remove drain plug.
Tip tiller forward to drain oil.
After oil has drained completely, replace oil drain plug
and tighten securely.
•
•
Remove oil filler plug. Be careful not to allow dirt to
enter the engine.
Refillenginewithoil. See“CHECKENGINEOILLEVEL”
in the Operation section of this manual.
Air Cleaner
Screws
Fig. 13
11
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
COOLING SYSTEM (See Fig. 14)
MUFFLER
Your engine is air cooled. For proper engine performance
and long life keep your engine clean.
Do not operate tiller without muffler. Do not tamper with
exhaustsystem.Damagedmufflersorsparkarresterscould
create a fire hazard. Inspect periodically and replace if
necessary. If your engine is equipped with a spark arrester
screen assembly, remove every 50 hours for cleaning and
inspection. Replace if damaged.
•
•
•
Clean air screen frequently using a stiff-bristled brush.
Remove blower housing and clean as necessary.
Keep cylinder fins free of dirt and chaff.
SPARK PLUG
Replace spark plugs at the beginning of each tilling sea-
son or after every 50 hours of use, whichever comes first.
Spark plug type and gap setting are shown in “PRODUCT
SPECIFICATIONS” on page 3 of this manual.
Muffler
TRANSMISSION
Your transmission is sealed and will not require lubrication
unless serviced.
Cylinder Fins
CLEANING
Do not clean your tiller when the engine and transmission
are hot. We do not recommend using pressurized water
(garden hose, etc.) to clean your unit unless the gasket
area around the transmission and the engine muffler, air
filter and carburetor are covered to keep water out. Water
in engine will shorten the useful life of your tiller.
Blower
Air Screen
•
•
•
Clean engine, wheels, finish, etc. of all foreign mat-
Housing
ter.
Fig. 14
Keep finished surfaces and wheels free of all gasoline,
oil, etc.
Protect painted surfaces with automotive type wax.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE AND ADJUSTMENTS
CAUTION: Disconnect spark plug wire from spark plug and place wire where it cannot come into
contact with plug.
MID-WIDTH TILLING - 24" PATH (See Fig. 17)
TILLER
•
Assemble holes “A” in tine hubs to holes “C” in tine
shaft.
TO ADJUST HANDLE HEIGHT (See Fig. 15)
Factoryassemblyhasprovidedlowesthandleheight. Select
handle height best suited for your tilling conditions. Handle
height will be different when tiller digs into soil.
A
C
A
C
•
If a higher handle height is desired, loosen the four
nuts securing handle panel to engine brackets.
•
•
Slide handle panel to desired location.
Tighten the four nuts securely.
tine_5
Fig. 17
ENGINE BRACKETS
NARROW TILLING/CULTIVATING - 12-3/4" PATH
(See Fig. 18)
HANDLE
PANEL
•
Remove outer tines.
NUTS (ALSO 2
ON LEFT SIDE
OF TILLER)
tine_6
Fig. 15
INNER TINES ONLY
TINE ARRANGEMENT
Youroutertinescanbeassembledinseveraldifferentways
Fig. 18
to suit your tilling or cultivating needs.
NOTE: When reassembling outer tines, be sure right tine
assembly (marked “R”) and left tine assembly (marked “L”)
are mounted to correct side of tine shaft.
CAUTION: Tines are sharp. Wear
gloves or other protection when han-
dling tines.
TINE OPERATION CHECK (See Fig. 19)
NORMAL TILLING - 26" PATH (See Fig. 16)
WARNING: Disconnectsparkplugwire
fromsparkplugtopreventstartingwhile
checking tine operation.
•
Assemble holes “A” in tine hubs to holes “B” in tine
shaft.
OUTER
TINE
CLEVIS
PIN
Forpropertineoperation, forwardtinecontrollevermustbe
againstcontrolbodyandallslackremovedfrominnerwireof
control cable when control is in the “OFF” (up) position.
Ifleverandcableareloose,loosencableclipatlowerendof
cable. Pull up on cable to remove slack, without extending
spring on end of cable, and retighten cable clip.
A
A
B
B
FINAL CHECK “OFF” POSITION
tine_4
•
•
•
With tine control “OFF” (up), push down on handle to
HAIRPIN CLIP
INNER TINE
raise tines off the ground.
Slowly pull recoil starter handle while observing tines.
Tines should not rotate.
If tines rotate, inner wire of control cable is too tight
which is extending lower spring and engaging tines.
Loosencableclipandpushdownoncableonlyenough
to relieve spring tension. Tighten cable clip.
Recheck in “OFF” position and adjust if necessary.
Fig. 16
•
13
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE AND ADJUSTMENTS
FINAL CHECK “ON” POSITION
TO REPLACE V-BELT (See Fig. 21)
•
•
•
Withtinecontrol“ON”(helddowntohandle)pushdown
Replace V-belt if it has stretched considerably or if it has cracks
or frayed edges.
on handle to raise tines off the ground.
Slowly pull recoil starter handle while observing tines.
Tines should rotate forward.
If tines do not rotate, inner wire of control cable is too
loose. Loosen cable clip and pull cable up to remove
slack and retighten clip.
•
Belt guard must be removed to service belt. See “TO
REMOVE BELT GUARD” in this section of manual.
LT REMOVAL
•
Remove V-belt from transmission pulley first and then
from engine pulley.
•
Recheck in “ON” position and adjust if necessary.
NOTE: If“ON”positioncheckrequiredadjustment,recheck
“OFF”positionadjustmenttoinsuretinesdonotrotatewhen
control is “OFF” (up).
BELT REPLACEMENT
•
InstallnewV-belttoenginepulleyfirstthentotransmis-
sion pulley. Be sure belt is positioned on inside groove
of both pulleys, inside all belt guides and rests on idler
pulley.CHECK TINE OPERATION
FORWARD TINE
CONTROL IN “OFF”
(UP) POSITION
•
•
See “TINE OPERATION CHECK” in this section of
manual.
Replace belt guard.
TINE CONTROL
“ON” POSITION
BODY
BELT GUIDE
ENGINE PULLEY
TINE CONTROL CABLE
CABLE CLIP
V-BELT
BELT GUIDE
TRANSMISSION
PULLEY
IDLER PULLEY
Fig. 21
ENGINE
TO ADJUST CARBURETOR
Fig. 19
Thecarburetorhasbeenpresetatthefactoryandadjustment
should not be necessary. However, engine performance
can be affected by differences in fuel, temperature, altitude
or load. If the carburetor does need adjustment, contact
your nearest authorized service center/department
IMPORTANT: NEVERTAMPERWITHTHEENGINEGOVERNOR,
WHICH IS FACTORY SET FOR PROPER ENGINE SPEED.
OVERSPEEDING THE ENGINE ABOVE THE FACTORY HIGH
SPEED SETTING CAN BE DANGEROUS. IF YOU THINK THE
ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING,
CONTACTYOURNEARESTAUTHORIZEDSERVICECENTER/
DEPARTMENT, WHICH HAS THE PROPER EQUIPMENT AND
EXPERIENCE TO MAKE ANY NECESSARY ADJUSTMENTS.
TO REMOVE BELT GUARD (See Fig. 19)
•
•
•
Remove screws from side of belt guard.
Pull belt guard out and away from unit.
Replace belt guard by reversing above procedure. Be
sure slot in bottom of belt guard is under head of tine
shield bolt and all nuts are tightened securely.
BELT GUARD
SCREW
SCREW
SCREW
Fig. 20
14
Download from Www.Somanuals.com. All Manuals Search And Download.
STORAGE
Immediately prepare your tiller for storage at the end of the
ENGINE OIL
Drainoil(withenginewarm)andreplacewithcleanoil. (See
“ENGINE” in the Maintenance section of this manual).
season or if the unit will not be used for 30 days or more.
WARNING: Never store the tiller with
gasoline in the tank inside a building
where fumes may reach an open flame
orspark. Allowtheenginetocoolbefore
storing in any enclosure.
CYLINDER(S)
•
•
Remove spark plug.
Pour 1 ounce (29 ml) of oil through spark plug hole into
cylinder.
TILLER
•
•
Pull starter handle slowly several times to distribute
oil.
Replace with new spark plug.
•
Cleanentiretiller(See“CLEANING”intheMaintenance
section of this manual).
•
Inspect and replace belts, if necessary (See belt re-
placement instructions in the Service and Adjustments
section of this manual).
•
•
Lubricate as shown in the Maintenance section of this
OTHER
manual.
•
•
Do not store gasoline from one season to another.
Be sure that all nuts, bolts and screws are securely
fastened. Inspect moving parts for damage, breakage
and wear. Replace if necessary.
Touch up all rusted or chipped paint surfaces; sand
lightly before painting.
Replace your gasoline can if your can starts to rust.
Rust and/or dirt in your gasoline will cause problems.
•
•
If possible, store your unit indoors and cover it to give
protection from dust and dirt.
Cover your unit with a suitable protective cover that
does not retain moisture. Do not use plastic. Plastic
cannot breathe which allows condensation to form and
will cause your unit to rust.
•
ENGINE
IMPORTANT: NEVER COVER TILLER WHILE ENGINE AND
EXHAUST AREAS ARE STILL WARM.
FUEL SYSTEM
IMPORTANT:ITISIMPORTANTTOPREVENTGUMDEPOSITS
FROMFORMINGINESSENTIALFUELSYSTEMPARTSSUCH
AS THE CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK
DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT
ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING
ETHANOLORMETHANOL)CANATTRACTMOISTUREWHICH
LEADSTOSEPARATIONANDFORMATIONOFACIDSDURING
STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM
OF AN ENGINE WHILE IN STORAGE.
•
•
•
Empty the fuel tank by starting the engine and let it run
until the fuel lines and carburetor are empty.
Never use engine or carburetor cleaner products in the
fuel tank or permanent.
Use fresh fuel next season.
NOTE: Fuel stablizer is an acceptable alternative in
minimizing the formation of fuel gum deposits during
storage. Add stabilizer to gasoline in fuel tank or storage
container. Always follow the mix ratio found on stablizer
container. Run engine at least 10 minutes after adding
stablizer to allow the stabilizer to reach the carburetor.
Do not empty the gas tank and carburetor if using fuel
stabilizer.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING POINTS
PROBLEM
CAUSE
CORRECTION
Will not start
1. Out of fuel.
1. Fill fuel tank.
2. Engine not “CHOKED” properly.
3. Engine flooded.
4. Dirty air cleaner.
5. Water in fuel.
2. See “TO START ENGINE” in the Operation section.
3. Wait several minutes before attempting to start.
4. Clean or replace air cleaner cartridge.
5. Empty fuel tank and carburetor, and refill tank with
fresh gasoline.
6. Clogged fuel tank.
7. Loose spark plug wire.
6. Remove fuel tank and clean.
7. Make sure spark plug wire is seated properly on
plug.
8. Bad spark plug or improper gap.
9. Carburetor out of adjustment.
8. Replace spark plug or adjust gap.
9. Make necessary adjustments.
Hard to start
1. Throttle control not set properly.
2. Dirty air cleaner.
3. Bad spark plug or improper gap.
4. Stale or dirty fuel.
1. Place throttle control in “FAST” position.
2. Clean or replace air cleaner cartridge.
3. Replace spark plug or adjust gap.
4. Empty fuel tank and refill with fresh gasoline.
5. Make sure spark plug wire is seated properly on
plug.
5. Loose spark plug wire.
6. Carburetor out of adjustment.
6. Make necessary adjustments.
Loss of power
1. Engine is overloaded.
2. Dirty air cleaner.
3. Low oil level/dirty oil.
4. Faulty spark plug.
5. Oil in fuel.
1. Set depth stake and wheels for shallower tilling.
2. Clean or replace air cleaner cartridge.
3. Check oil level/change oil.
4. Clean and regap or change spark plug.
5. Empty and clean fuel tank and refill, and clean
carburetor.
6. Stale or dirty fuel.
7. Water in fuel.
6. Empty fuel tank and refill with fresh gasoline.
7. Empty fuel tank and carburetor, and refill tank with
fresh gasoline.
8. Clogged fuel tank.
8. Remove fuel tank and clean.
9. Connect and tighten spark plug wire.
10. Clean engine air screen.
11. Clean/replace muffler.
12. Make necessary adjustments.
13. Contact an authorized service center/department.
9. Spark plug wire loose.
10. Dirty engine air screen.
11. Dirty/clogged muffler.
12. Carburetor out of adjustment.
13. Poor compression.
Engine overheats
1. Low oil level/dirty oil.
2. Dirty engine air screen.
3. Dirty engine.
4. Partially plugged muffler.
5. Improper carburetor adjustment.
1. Check oil level/change oil.
2. Clean engine air screen.
3. Clean cylinder fins, air screen, muffler area.
4. Remove and clean muffler.
5. Adjust carburetor to richer position.
Excessive bounce/
difficult handling
1. Ground too dry and hard.
1. Moisten ground or wait for more favorable soil
conditions.
2. Adjust wheels and depth stake.
2. Wheels and depth stake incorrectly adjusted.
Soil balls up or clumps
1. Ground too wet.
1. Wait for more favorable soil conditions.
Engine runs but tiller
won’t move
1. Tine control is not engaged.
2. V-belt not correctly adjusted.
3. V-belt is off pulley(s).
1. Engage tine control.
2. Inspect/adjust V-belt.
3. Inspect V-belt.
Engine runs but labors
when tilling
1. Tilling too deep.
2. Throttle control not properly adjusted.
3. Carburetor out of adjustment.
1. Set depth stake for shallower tilling.
2. Check throttle control setting.
3. Make necessary adjustments.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE NOTES
17
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE NOTES
18
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE NOTES
19
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from de-
fects in materials and workmanship. For a period of one (1) years from date of purchase by the original consumer
purchaser, we will repair or replace, at our option, without charge for parts or labor incurred in replacing parts, any
part which we find to be defective due to materials or workmanship. This Warranty is subject to the following limita-
tions and exclusions.
1. This warranty does not apply to the engine or components parts thereof. Please refer to the applicable manu-
facturer's warranty on these items.
2. Transportation charges for the movement of any power equipment unit or attachment are the responsibility of
the purchaser. Transportation charges for any parts submitted for replacement under this warranty must be paid
by the purchaser unless such return is requested by the manufacturer.
3. The Warranty period for any products used for rental or commercial purposes is limited to 90 days from the date
of original purchase.
4. This Warranty applies only to products which have been properly assembled, adjusted, operated, and maintained
in accordance with the instructions furnished. This Warranty does not apply to any product which has been
subjected to alteration, misuse, abuse, improper assembly or installation, delivery damage, or to normal wear
of the product.
5. Exclusions: Excluded from this Warranty are belts, tines, tine adapters, normal wear, normal adjustments, stan-
dard hardware and normal maintenance.
6. In the event you have a claim under this Warranty, you must return the product to an authorized service deal-
er.
Should you have any unanswered questions concerning this Warranty, please contact:
In Canada contact:
McCulloch
McCulloch
Customer Service Dept.
1030 Stevens Creek Road
Augusta, GA 30907 USA
7075 Ordan Drive
Mississauga, Ontario
L5T 1K6
giving the model number, serial number and date of purchase of your product and the name and address of the
authorized dealer from whom it was purchased.
THIS WARRANTY DOES NOT APPLY TO INCIDENTAL OR CONSEQUENTIAL DAMAGES AND ANY IMPLIED
WARRANTIES ARE LIMITED TO THE SAME TIME PERIODS STATED HEREIN FOR OUR EXPRESSED WAR-
RANTIES. Some areas do not allow the limitation of consequential damages or limitations of how long an implied
Warranty may last, so the above limitations or exclusions may not apply to you. This Warranty gives you specific legal
rights, and you may have other rights which vary from locale to locale.
This is a limited Warranty within the meaning of that term as defined in the Magnuson-Moss Act of 1975.
11.16.09 TH
Printed in U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
|