STACKED LAUNDRY
TABLE OF CONTENTS
Welcome ................................. Inside Cover
Safety Instructions................................. 1-2
Washer Controls At A Glance............... 3-4
Washer Special Features.......................... 5
Washer Operating Tips ............................. 6
Dryer Controls At A Glance .................. 7-8
Dryer Operating Tips................................. 8
Dryer Exhaust Tips.................................... 9
Care and Cleaning................................... 10
Storage..................................................... 10
Before You Call................................... 11-13
Water Use ................................................ 13
Warranty..................................... Back Page
®
KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Notice and Instructions
U
The California Safe Drinking Water and Toxic
Enforcement Act of 1986 (Proposition 65) requires the
Governor of California to publish a list of substances
known to the State of California to cause cancer or
reproductive harm, and requires businesses to warn cus-
tomers of potential exposures to such substances.
Appliances with the
symbol on the data plate have
®
L
been listed with Underwriters’ Laboratories, Inc. Those
with a CSA Monogram on the data plate have been cer-
tified by the CSA Testing Laboratories as complying
with Canadian Standards Association requirements. Gas
dryers with an AGA symbol on the data plate have been
design certified with the American Gas Association;
those with a CGA symbol on the data plate have been
approved by the Canadian Gas Association.
Nevertheless, as with any equipment using electricity
and having moving parts, there are potential hazards. To
use this appliance safely, the operator should become
familiar with the instructions for operation of the appli-
ance and always exercise care when using it.
Users of this appliance are hereby warned that the burn-
ing of gas can result in low-level exposure to some of
the listed substances, including benzene, formaldehyde
and soot, due primarily to the incomplete combustion of
natural gas or liquid petroleum (LP) fuels. Exhaust ducts
should be kept free of obstructions and properly
exhausted dryers will minimize exposure.
WARNING — Do not place into your
dryer items that have been spotted or
soaked with vegetable oil or cooking oil.
Even after being washed, these items may
contain significant amounts of these oils.
The remaining oil can ignite spontaneously.
The potential for spontaneous ignition
increases when the items containing veg-
etable oil or cooking oil are exposed to
heat. Heat sources, such as your clothes
dryer, can warm these items, allowing an
oxidation reaction in the oil to occur.
Oxidation creates heat. If this heat cannot
escape, the items can become hot enough
to catch fire. Piling, stacking or storing
these kinds of items may prevent heat from
escaping and can create a fire hazard.
WARNING — For your safety the
information in this manual must be
followed to minimize the risk of fire or
explosion or to prevent property dam-
age, personal injury or death.
– Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
– WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch;
do not use any phone in your build-
ing.
• Clear the room, building or area of
all occupants.
All washed and unwashed fabrics that con-
tain vegetable oil or cooking oil can be dan-
gerous. Washing these items in hot water
with extra detergent will reduce, but will
not eliminate, the hazard. Always use the
“cool down” cycle for these items to
reduce the items’ temperature. Never
remove these items from the clothes dryer
hot or interrupt the drying cycle until the
items have run through the “cool down”
cycle. Never pile or stack these items when
they are hot.
• Immediately call your gas supplier
from a neighbor’s phone. Follow the
gas supplier’s instructions.
• If you cannot reach your gas suppli-
er, call the fire department.
Installation and service must be per-
formed by a qualified installer, service
agency or the gas supplier.
Save These Instructions
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
WARNING — To reduce the risk of fire, explosion, electric shock, property damage or injury
to persons when using your appliance, follow basic precautions, including the following:
1. Read all instructions before using the appliance.
2. To avoid the possibility of fire or explosion:
6. Do not install or store this appliance where it will be
exposed to the weather.
7. Do not tamper with controls.
a. Do not wash or dry items that have been previously
cleaned in, washed in, soaked in, or spotted with gaso-
line, dry-cleaning solvents, other flammable or explo-
sive substances as they give off vapors that could ignite
or explode. Hand wash and line dry any items contain-
ing these substances.
8. Do not repair or replace any part of the appliance or
attempt any servicing unless specifically recommended
in published user-repair instructions that you understand
and have the skills to carry out.
9. The agitator should not be removed. If the agitator is
removed, it must be replaced by pushing down complete-
ly and the locking screw tightened before the washer is
operated.
Any material on which you have used a cleaning sol-
vent, or which is saturated with flammable liquids or
solids, should not be placed in the appliance until all
traces of these liquids or solids and their fumes have
been removed.
10. Do not use fabric softeners or products to eliminate stat-
ic unless recommended by the manufacturer of the fabric
softener or product.
These items include acetone, denatured alcohol, gaso-
line, kerosene, some liquid household cleaners, some
spot removers, turpentine, waxes and wax removers.
11. Clean the dryer lint screen before or after each load.
12. Keep the area around the exhaust opening and surround-
ing areas free from lint accumulation, dust and dirt.
b. Do not add gasoline, dry-cleaning solvents, or other
flammable or explosive substances to the wash water.
These substances give off vapors that could ignite or
explode.
13. The interior of the dryer and exhaust duct should be
cleaned periodically by qualified service personnel.
14. This appliance must be properly grounded. Never plug
the appliance cord into a receptacle which is not ground-
ed adequately and in accordance with local and national
codes. See Installation Instructions for grounding this
appliance.
c. Under certain conditions, hydrogen gas may be pro-
duced in a hot water system that has not been used for
2 weeks or more. HYDROGEN GAS IS EXPLO-
SIVE. If the hot water system has not been used for
such a period, before using a washing machine or
combination washer-dryer, turn on all hot water
faucets and let the water flow from each for several
minutes. This will release any accumulated hydrogen
gas. As the gas is flammable, do not smoke or use an
open flame during this time.
15. Unplug power supply cord before attempting to service
your appliance.
16. Store laundry aids and other material in a cool, dry place
where children cannot reach them.
17. Do not use chlorine bleach and ammonia or acids (such
as vinegar or rust remover) in the same wash. Hazardous
fumes can form.
d. Items containing foam rubber (may be labeled latex
foam) or similarly textured rubber-like materials must
not be dried on a heat setting. Foam rubber materials
when heated, can under certain circumstances produce
fire by spontaneous combustion.
18. Do not machine wash fiberglass materials. Small parti-
cles can stick to fabrics washed in following loads and
cause skin irritation.
e. Do not wash or dry items that are soiled with veg-
etable or cooking oil. These items may contain some
oil after laundering. Due to the remaining oil, the fab-
ric may smoke or catch fire by itself.
19. Before the appliance is removed from service or discard-
ed, remove the door to the clothes dryer compartment.
20. Install and level washer on a floor that can support the
weight.
3. Do not allow children to play on or in the appliance.
Close supervision of children is necessary when the
appliance is used near children.
21. As with any equipment using electricity and having mov-
ing parts, there are potential hazards. To use this appli-
ance safely, the operator should become familiar with the
instructions for operation of the appliance and always
exercise care when using it.
4. Before the appliance is removed from service or discard-
ed, remove the door to the clothes washer compartment.
5. Do not reach into the appliance if the tub, agitator, or
drum is moving.
Save These Instructions
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Washer Controls At A Glance
Step
Select Cycle
1
Press the control knob in and turn clockwise to the desired
cycle. Pull the control knob out to start the washer.
PERMANENT PRESS is designed to mini-
mize wrinkles with a cool-down spray rinse
following the wash. Times available are:
14 minutes – Use for heavily soiled or stained
clothes.
10 minutes – Use for normally soiled clothes.
6 minutes – Use for lightly soiled clothes.
REGULAR FABRICS is used for normal,
sturdy fabrics. Times available are:
18 minutes – Use for very heavily soiled or
stained clothes
14 minutes – Use for heavily soiled or
stained clothes.
10 minutes – Use for normally soiled clothes.
6 minutes – Use for lightly soiled clothes.
The controls for the stacked washer
and dryer are convenient and easy to
use. The washer and dryer can oper-
ate at the same time or independently
of each other.
KNITS/DELICATES is designed for items
requiring delicate wash action. It provides
alternating periods of wash and soak for
approximately 10 minutes.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Step
Select Load Size
2
Turn the LOAD SIZE knob
to the SMALL, MEDIUM,
or LARGE setting.
WATER LEVEL SETTING
LOAD SIZE
Large
Medium
Small
3/4 – Full
1/2 – 3/4 Full
1/3 Full
For best washing results,
clothes must circulate
freely. If too little water is
used, poor cleaning, linting,
and excessive wear may
result.
REMEMBER: Items must circulate
freely for best results.
NOTE: When laundering permanent press items, delicates,
washable woolen or loosely knit items, never use less than the
MEDIUM setting. This will minimize shrinkage, wrinkling,
and pulling of seams.
Step
Select Water Temperature
3
WASH/RINSE TEMPS
LOAD TYPE
Turn the TEMPERATURE
knob to the desired water temper-
atures. Follow the garment care
label for best results. Use the
chart to the right as a guide.
White and heavily
soiled, color-fast
items
Hot/Cold
Moderately soiled,
colored items; most
permanent press
items
Warm/Cold
Cold/Cold
REMEMBER: In wash
water temperatures below 65º
F, detergents do not dissolve
well or clean well. Care
labels define cold water as up
to 85º F.
Brightly colored,
lightly soiled items;
washable woolens
Step
Start Washer
4
• Add detergent.
• Add laundry load and close lid.
• Pull out control knob to start.
NOTE: The washer is automatically programmed
to assure proper agitation and spinning for each
load type. REGULAR FABRICS will provide a
fast wash/spin speed. PERMANENT PRESS will
have a fast wash/spin speed along with a cool-
down spray rinse. KNITS/DELICATES will have
alternating periods of wash and soak and fast
final spin speed.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Washer Special Features
Lift the Lid
The washer lid lifts up and down to open and close.
Internal springs will hold the lid in the open position
until pulled down to close.
This washer is designed so that it will not fill, agitate or
spin when the lid is open. Should the lid be opened dur-
ing a cycle, the washer will stop; when the lid is closed
and the control knob is pulled out, the washer will
resume its cycle at the point it was interrupted.
Bleach Dispenser
Fabric Softener Dispenser
The dispenser automatically dilutes liquid chlorine
bleach before it reaches your wash load. To use, follow
these steps:
This dispenser automatically releases liquid fabric soft-
ener at the proper time during the cycle. To use, follow
these steps:
1. Measure liquid chlorine bleach carefully, following
the instructions on the bottle.
1. Pour liquid fabric softener into the dispenser using
the amount recommended on the package.
2. Add the bleach to the dispenser before adding the
load. Avoid splashing or over-filling the dispenser.
2. Add warm water to the dispenser until it reaches the
FILL LINE.
NOTE:
NOTE:
• Never pour undiluted liquid chlorine bleach directly
onto the load or into the wash tub. It is a powerful
chemical and can cause fabric damage, such as tear-
ing or color loss, if not used properly.
• Do not stop the washer during the first spin. This will
cause the dispenser to empty too soon.
• Never pour fabric softener directly on the load. It will
leave spots and stains.
• If you prefer to use color-safe, non-chlorine bleach,
pour it into the wash tub with your detergent. Do not
pour non-chlorine bleaches into the bleach dispenser.
• Use the dispenser for liquid fabric softeners only.
Clean the area in and around the dispenser frequently
with hot water, detergent and a soft brush.
Pour liquid fabric softener into cup and
dilute with warm water.
Pour liquid chlorine bleach into
the bleach dispenser.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Washer Operating Tips
For detailed information on sorting, pretreating stains,
etc., see the enclosed Laundering Tips pamphlet.
Loading
• Put dry, unfolded clothes loosely in the tub, up to the
top row of holes for a maximum load.
Detergent
• Do not wrap large items like sheets around the agita-
tor.
• Use either liquid or granular laundry detergent. For
best results, be sure detergent is added to the
washer BEFORE the load and be sure wash water
is above 65º F.
• Mix large and small items for best circulation. Wash
bulky items like blankets separately.
• When laundering permanent press items or items of
delicate construction, washable woolens or loosely
knit items, never use less than the MEDIUM water
level setting. This will minimize shrinkage, wrinkling
and pulling of seams.
• Use the correct amount of detergent for the load size,
soil level and water conditions. Use more detergent if
you have hard water and very soiled loads.
If you have soft water or a lightly soiled load, use less
detergent. (See manufacturer’s instructions.)
• For best results, add the detergent to the washtub
before adding the load.
• Wipe up any detergent spills on the washer.
Additional Tips
• This washer is designed so that it will not fill, agitate
or spin when the lid is open.
• If the washer stops during the spin, it may be due to
an unevenly distributed load. If this happens, push in
the control knob, open the lid, redistribute the load,
close the lid and pull out the control knob. The spin
will resume at the point it was interrupted.
• If you open the lid during a cycle, the washer will
stop. When the lid is closed and the control knob
pulled out, the washer will continue the cycle at the
point it was interrupted.
• The washer will pause briefly throughout each cycle.
These pauses are normal.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Dryer Controls At A Glance
IntelliDry REGULAR FABRICS automati-
Step
Select Cycle
1
cally senses the moisture in the load and
shuts off when the selected dryness level is
reached. This cycle is designed for loads
such as towels, underwear, t-shirts, jeans,
etc. Set the control to the desired dryness
level (more dry – less dry) and press the
START button. The middle ▲ is the initial
preferred setting for the majority of loads.
WRINKLE RELEASE will release wrinkles
from items that are clean and dry but slight-
ly wrinkled. This cycle is for clothes from a
crowded closet or suitcase or from sitting in
the dryer too long after the end of the cycle.
It provides 10 minutes of heated tumbling
and 5 minutes of cool-down tumbling with-
out heat. Press the START button for the
cycle to begin.
DAMP DRY is designed to “partially” dry
items. It provides approximately 20 minutes
of heated tumbling and 5 minutes of cool-
down tumbling without heat. Press the
START button to begin tumbling.
TIME DRY may be selected for any load if
the IntelliDry sensor system is not desired.
Set the control to the desired number of
minutes and choose the appropriate drying
temperature for the load. Then press the
START button.
IntelliDry PERM’T PRESS with Press Care
automatically senses the moisture in the
load and shuts off when the selected dryness
level is reached. Permanent Press minimizes
wrinkles of man-made fabrics such as
acrylic, nylon, polyester, or blends with an
extended cool-down by tumbling the load in
unheated air at the end of the cycle. Simply
set the control to the desired dryness level
(more dry – less dry) and press the START
button. The middle ▲ is the initial preferred
setting for the majority of loads.
AIR FLUFF provides tumbling without heat
for sensitive loads or items needing freshen-
ing. Examples are: certain sweaters, shower
curtains, camping gear, pillows, etc. Set the
control to the desired number of minutes, up
to 20 minutes, and press the START button.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Step
Select Temperature
Step
Press Start
2
3
Turn the TEMPERATURE selection knob to the
appropriate drying temperature. The choices
are:
Push this button to start the dryer. The dryer door
must be shut for the dryer to operate. If the door is
opened during the cycle, the start button must be
pushed again to resume the cycle once the door is
closed.
REGULAR – for sturdy cottons or those labeled
“Tumble Dry”.
When the cycle is complete, a signal will sound
momentarily.
DELICATE – for heat sensitive items labeled
“Tumble Dry Low” or “Tumble Dry Warm”.
Dryer Operating Tips
Load the Dryer Properly...
Clean the
Lint Filter...
• by placing only one washload in the dryer at
a time.
• after each load.
• by avoiding very small loads or mixed loads.
• to shorten drying time.
• to operate more energy efficient.
• by adding one or more similar items to the dryer
when only one or two articles need drying. This
improves the tumbling action and drying efficiency.
NOTE: Do not operate the dryer without the lint
filter in place.
Add A Fabric Softener Sheet...
(If So Desired)
• after loading the dryer.
• to control static cling.
• before the load becomes warm. This helps prevent
greasy–looking softener stains.
• and remove any used softener sheets from the dryer
to prevent greasy–looking softener stains.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Dryer Exhaust Tips
WARNING — Plastic or nonmetal flexible duct presents a potential fire hazard.
Do
Don’t
Read the installation instructions and
the user’s guide.
Let a poor exhaust system cause
slow drying.
Do
Don’t
Let your
dryer exhaust
the air easily.
Restrict your dryer
with a poor
exhaust system.
Don’t
Do
Use plastic, thin
foil, or non-
metal flexible
duct.
Use 4 inch diameter
rigid metal duct. Tape all joints.
Never use lint-trapping screws.
Don’t
Do
Use longer than
necessary duct
runs with many
elbows.
Keep duct runs
as straight as
possible.
Don’t
Do
Allow crushed
or clogged
ducts and vent.
Clean all old ducts
before installing your new
dryer. Be sure vent flap
opens and closes freely.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and Cleaning
Control Panel Care
Dryer Care
Clean the control panel with a soft damp cloth. Do not
use any abrasive powders or cleaning pads.
Tumbler
If the tumbler becomes stained by a crayon, ink pen or
other item inadvertently left in a garment, clean the tum-
bler with an all purpose cleaner such as: Fantastik, Soft
Scrub or Formula 409®.* Then tumble old towels or
rags to remove any excess stain or cleaning substance.
Cabinet Care
Simply wipe off any marks with soap and water, fol-
lowed with an appliance wax if desired.
Exhaust System Cleaning
While the lint filter will catch most of the lint from the
load, some will get through and may buildup in the
ductwork. It is important to completely inspect and
clean all lint accumulation from the interior of the duct-
work once a year to maintain drying performance. The
exhaust hood at the outside of the home should be
cleaned more frequently to ensure the damper opens and
closes freely.
Washer Care
Lint Filter
The SELF-CLEAN LINT FILTER in the washer is
located under the agitator and cleans itself. During the
wash and rinse portion of the cycle, lint is collected on
the filter. The filter is then flushed automatically during
the spin and drain.
Refer to the Installation Instructions for more details on
proper exhausting.
Interior
*Brand names are trademarks of the respective
manufacturers.
Hard water deposits may be removed, if needed, using a
recommended cleaner labeled washer safe.
Storing the Washer and Dryer
Washers can be damaged if water is not removed from
hoses and internal components before storage. Prepare
the washer and dryer for storage as follows:
• Advance the cycle control knob to the final spin of
the Regular Fabrics cycle and lower drain hose to
drain any water that may be in the drain hose.
• Disconnect the washer and dryer from the electri-
cal supply and leave the washer lid open to let air
circulate inside the tub.
• Select the Regular Fabrics cycle and add one cup
of bleach or white vinegar to a full load of warm or
hot water without clothes. Run the washer through
a complete cycle.
• Clean the dryer tumbler with an all purpose clean-
er such as Fantastik or Formula 409®* and dis-
connect from the power supply.
• Turn the water faucets off and disconnect the inlet
hoses.
NOTE: For extended periods of storage or storage during extreme cold temperatures, call
Maytag Customer Service in the U.S. at 1-800-688-9900 or in Canada at 1-800-688-2002.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Call
For problem laundry solutions (i.e. fabric damage, residue, tangling) and special laundry care proce-
dures, see the enclosed Laundering Tips pamphlet.
Check these points if your clothes washer...
• Plug cord into live electrical outlet.
• Check fuse or reset circuit breaker.
• Close lid and pull control knob out to start the washer. For your safety,
washer will not fill unless the lid is closed.
• Turn both faucets on fully.
Won’t Fill
• Straighten inlet hoses.
• Disconnect hoses and clean screens. Hose filter screens may be plugged.
• Check fuse or reset circuit breaker.
• Turn the control knob to proper cycle and pull knob out to start the washer.
• Close lid and pull control knob out to start the washer. For your safety,
washer will not agitate or spin unless the lid is closed.
Won’t Agitate
• Unevenly distributed load. Redistribute the load, close the lid and pull knob
out. Check for leveling. Be sure water level is acceptable for load size.
• Check fuse or reset circuit breaker.
• Straighten drain hoses. Eliminate kinked hoses. If there is a drain restriction,
call for service.
• Close lid and pull control knob out to start the washer. For your safety, wash-
er will not agitate or spin unless the lid is closed.
Won’t Spin
or Drain
• Suds lock – caused by too much suds. Rewash without detergent. Use cor-
rect amount of a low-sudsing detergent.
(Continued on next page.)
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Call (continued)
Check these points if your clothes washer...
• Unevenly distributed load. Redistribute the load, close the lid and pull knob
out. Check for leveling. Be sure water level is acceptable for load size.
• Plug cord into live electrical outlet.
• Check fuse or reset circuit breaker.
• Turn the control knob to proper cycle and pull knob out to start the washer.
If equipped with buttons, be sure they are fully depressed.
• Close lid and pull control knob out to start the washer. For your safety, wash-
er will not fill, agitate or spin unless lid is closed.
Stops
• This may be a pause or soak period in the cycle. Wait briefly and it may start.
• Make sure hose connections are tight.
• Make sure end of drain hose is correctly inserted and secured to drain
facility.
Leaks Water
• Avoid extended soaking – soak for 30 minutes or less.
• Avoid overloading.
• Be sure washer is leveled properly as outlined in installation manual.
• Weak floors can cause vibration and walking.
Is Noisy
• Be sure rubber feet are installed on leveling legs.
• Turn both faucets on fully.
• If equipped with a temperature selector knob, be sure it is set directly on a
temperature setting and not between settings.
• Make sure temperature selection is correct.
• Make sure hoses are connected to correct faucets and inlet connections.
Flush water line before filling washer.
• Check the water heater. It should be set to deliver a minimum 120°F (49°C)
hot water at the tap. Also check water heater capacity and recovery rate.
• Disconnect hoses and clean screens. Hose filter screens may be plugged.
Fills with
the Wrong
Temperature
Water
For further assistance contact Maytag Appliances Sales Company, Maytag Customer Assistance:
U.S. 1-800-688-9900 or Canada 1-800-688-2002
U.S. customers using TTY for deaf, hearing impaired or speech impaired, call 1-800-688-2080.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Call (continued)
Check these points if your clothes dryer...
• Be sure the door is latched shut.
• Be sure the power cord is plugged into a live electrical outlet.
Doesn’t Run
Doesn’t Heat
• Check the home’s circuit breaker and fuses.
• Press the START button again if the door is opened during the cycle.
• Check the home’s circuit breaker and fuses.
• Select a heat setting, not air-fluff.
• On a gas dryer, check that the gas supply is on.
• Clean the lint filter and exhaust duct.
• Check all of the above, plus...
• Be sure the exhaust hood at the outside of the home can open and close freely.
• Use 4” rigid metal exhaust duct.
Doesn’t Dry
• Do not overload. 1 Wash load = 1 Dryer load.
• Sort heavy items from lightweight items.
• Check that the washer is draining properly to extract adequate water from
the load.
• Check the load for objects such as coins, loose buttons, nails, etc.
Remove promptly.
Is Noisy
• Be sure the dryer is leveled properly as outlined in the installation manual.
• Be sure the rubber feet are installed on the leveling legs.
• This is normal operation for an IntelliDry cycle, especially at the beginning of
cycle. Once the load begins to dry, the control knob will start to advance. The
rate of advancement will be slow at the beginning of the cycle because there is
more moisture in the load. As the load becomes more dry, the control knob will
advance more quickly.
Control Knob
Advances Slowly
Water Use
REGULAR OR DELICATE CYCLE
PERMANENT PRESS CYCLE
Approx. 36 gallons
(30 Imperial gallons; 136 liters)
Approx. 41 gallons
(34 Imperial gallons; 155 liters)
Large
Medium
Small
Large
Approx. 28 gallons
(23 Imperial gallons; 106 liters)
Approx. 33 gallons
(27 Imperial gallons; 125 liters)
Medium
Small
Approx. 22 gallons
(18 Imperial gallons; 83 liters)
Approx. 26 gallons
(22 Imperial gallons; 98 liters)
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Full-size Stacked Washer & Dryer Warranty
Full One Year Warranty
For one (1) year from the date of original retail purchase, any part which fails in normal home use will be
repaired or replaced free of charge.
Limited Parts Warranty
After the first year from the date of original retail purchase through the time periods listed below, the parts des-
ignated below which fail in normal home use will be repaired or replaced free of charge for the part itself, with
the owner paying all other costs, including labor, mileage and transportation.
Second Year – All parts.
Third through Fifth Year – The washer drive motor. All parts of the solid state controls (if so equipped).
Third through Tenth Year – All parts of the washer transmission assembly.
Additional Limited Warranty Against Rust
Should any of the parts listed below rust during the one year period starting from the date of retail purchase,
repair of replacement will be made free of charge. After the first and through the fifth year, repair or replace-
ment will be made free of charge for the part itself, with the owner paying all other costs, including labor,
mileage and transportation.
Automatic Washer: Exterior cabinet, top, lid and baseframe.
Dryer: Exterior cabinet, top, door, clothes tumbler, tumbler front, tumbler back and stand.
This full warranty and the limited warranties apply when the appliance is located in the United States or Canada.
Appliances located elsewhere are covered by the limited warranties only, which include parts which fail during
the first year.
To Receive Warranty Service
To locate an authorized service company in your area contact the Maytag dealer from whom your appliance was purchased; or call Maytag
Appliances Sales Company, Maytag Customer Assistance at the number listed below. Should you not receive satisfactory warranty service,
please call or write:
Maytag Appliances Sales Company
Attn: CAIRSM Center
P.O. Box 2370
Cleveland, TN 37320-2370
U.S. 1-800-688-9900
Canada 1-800-688-2002
U.S. customers using TTY for deaf, hearing impaired or speech impaired, call 1-800-688-2080.
When contacting Maytag Appliances Sales Company, Maytag Customer Assistance about a service problem, please include the following:
(a) Your name, address and telephone number;
(b) Model number and serial number (found on lower right corner of dryer door opening) of your appliance;
(c) Name and address of your dealer and the date the appliance was purchased;
(d) A clear description of the problem you are having.
(e) Proof of purchase.
What is not covered by these warranties:
1. Conditions and damages resulting from any of the following:
a. Improper installation, delivery, or maintenance.
b. Any repair, modification, alteration or adjustment not autho-
rized by the manufacturer or an authorized servicer.
c. Misuse, abuse, accidents, or unreasonable use.
d. Incorrect electric current, voltage or supply.
4. Products purchased for commercial or industrial use.
5. The cost of service or service call to:
a. Correct installation errors.
b. Instruct the user on proper use of the product.
c. Transport the appliance to the servicer.
6. Consequential or incidental damages sustained by any person as
a result of any breach of these warranties.
e. Improper setting of any control.
2. Warranties are void if the original serial numbers have been
removed, altered, or cannot be readily determined.
Some states do not allow the exclusion or limitation of consequen-
tial or incidental damages, so the above exclusion may not apply.
3. Light bulb
User’s Guides, service manuals and parts catalogs are available from
Maytag Appliances Sales Company, Maytag Customer Assistance.
MAYTAG • One Dependability Square • Newton, Iowa 50208
Form No. 529CMB
Part No. 6 3160890
Download from Www.Somanuals.com. All Manuals Search And Download.
JN
Litho U.S.A.
|