MARVEL OUTDOOR REFRIGERATED WINE CELLAR
Installation
Operation
and
Maintenance
Instructions
Outdoor
Refrigerated
Wine Cellar
6OSWCE
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING YOUR OUTDOOR WINE CELLAR
Select Location
The proper location will ensure peak performance of your
appliance. Choose a location where the unit will be out of
direct sunlight and away from heat sources. Best perfor-
mance will be maintained when installed within the follow-
ing parameters:
WARNING
•
•
Do not splash or spray water from a hose on the re-
frigerator! Doing so may cause an electrical shock,
which may result in severe injury or death.
This unit should not, under any circumstances, be
ungrounded.
Unit should be operated in a properly ventilated area with
ambient temperatures above 40 degrees and below 100
degrees Fahrenheit.
Grounding Method
This product is factory equipped with a power supply cord
that has a three-pronged, grounded plug. It must be
plugged into a mating grounding type receptacle in ac-
cordance with the National Electrical Code and applicable
local codes and ordinances (see Figure 1). If the circuit
does not have a grounding type receptacle, it is the re-
sponsibility and obligation of the customer to exchange the
existing receptacle in accordance with the National Electri-
cal Code and applicable local codes and ordinances. The
third ground prong should not, under any circumstances,
be cut or removed. All U.L. listed refrigerated products are
equipped with this type of plug.
Cabinet Clearance
Ventilation is required from the bottom front section of the
unit. Keep this area open and clear of any obstructions.
Adjacent cabinets and countertop can be installed on top,
back and sides of the unit as long as the grille and door
access remain unobstructed. An opening of 24 inches is
required between cabinets and a depth of 24 inches.
Leveling Legs
Adjustable legs at the front corners of the unit should be
set so the unit is firmly positioned on the floor and the front
is raised just enough so that the door closes easily when
opened about halfway.
A ground fault circuit interrupter electrical receptacle is
to be used to supply electrical power to the refrigerator
for outdoor applications. Contact an electrician if you
need to install one to supply electrical power to your
outdoor refrigerator.
Turn leveling legs clockwise to raise unit, counterclockwise
to lower it.
Door Hinge Reversing
Electrical Connection
You can change the door swing from right- to left-hand
very easily. Simply unscrew the top and bottom hinge pin,
lift the door off the bottom hinge, and switch the hinges to
the other side. Screw the hinge pin back in what is now
the bottom hinge, unscrew the hinge pin in what is now the
top hinge, replace door, and screw the pin back in the top
hinge.
Check the serial nameplate for the correct power supply.
Use only the electrical power supply specified on the serial
nameplate. DO NOT USE AN EXTENSION CORD.
Figure 1
2
Download from Www.Somanuals.com. All Manuals Search And Download.
SENTRY SYSTEM™ REFRIGERATION MONITOR
55
Figure 2
Start Your Appliance
Interior Light and Switch
Your appliance will start upon initial plug-in. The LED will
flash amber upon initial plug-in due to your unit being
powered-on at the factory to verify performance and then
powered-off. The Sentry System™ refrigeration monitor
senses a power outage has occurred and relays this infor-
mation to you when you initially power-up your appliance.
This is normal and pressing the “ON/OFF” button will reset
this alarm function.
The interior light makes it easy to view your wine labels
and enhances the display of your collection. The light will
always come on when the door is opened.
Warning Alarms
Your wine cellar has been fitted with a Sentry System™
refrigeration monitor. This monitor will let you know if your
cellar is not functioning properly for optimum wine storage.
If your appliance’s control has been shut-off (i.e., unit
plugged in, interior lights operate, display blank), unit must
be turned on. To turn on your appliance, push and hold
for five (5) seconds, the “ON/OFF” button located on the
display panel (see Figure 2).
Door Ajar Alarm
If the door has been left open for over five (5) minutes, the
alarm will sound and the LED will flash green. This will
stop as soon as the door is closed.
High and Low Temperature
Once loaded with wine bottles, allow at least 48 hours for
the unit to stabilize before making any adjustments to the
initial setting.
If your unit reaches temperatures outside normal operating
temperatures for your set point for more than one (1) hour,
an alarm will sound and the LED will flash red. This will
warn you that your wines have seen temperatures that may
not be conducive for long-term storage.
Set Your Temperature Mode
This product can display either Fahrenheit or Celsius. To
do so, press the “°F/C” button on the display panel.
Power Failure
If your unit experiences a power failure, the LED will flash
amber until the alarm is reset.
Set the Controls
The available temperature range of the unit is from 40 to
65 degrees F. The temperature set point is initially set in
the factory at 55 degrees F. The temperature set point can
be lowered or raised by first pushing the “SET” button on
the display pad. A “SET” icon will be displayed. Pushing
either the “WARMER” or “COLDER” buttons located on the
display pad will raise or lower the set temperature by one
(1) degree F or C (depending on your setting). As with any
refrigeration product, there is a slight temperature variance
at different locations within the cabinet.
Reset Alarms
Press the “ON/OFF” button for approximately one (1) sec-
ond. This will reset all audible and display alarms.
Sabbath Mode
Your wine cellar is equipped with a Sabbath Mode feature.
By activating this mode, you will be disabling all displays,
audible alarms and lights.
To activate the Sabbath Mode, press and hold the “SET”
button while pressing the “°F/C” button four (4) times within
seven (7) seconds. To deactivate Sabbath Mode, repeat the
process. Sabbath Mode will automatically deactivate after
72 hours.
Adjustable Temperature Control
The temperature control is fully adjustable from the low
forties to the mid-sixties. The range allows flexibility of
temperature preferences.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
6OSWCE WINE CELLAR FEATURES
Insert Wine Bottles
Front Bottles (Necks Facing Rear)
Rear Bottles (Necks Facing Front)
The six (6) roll-out shelves each hold eight (8) bottles. See
Figure 3 for typical wine bottle spacing. Tall bottles should
not be loaded on the bottom rack because they may pre-
vent the door from closing.
Loading Tips and Suggestions
Position white wines on the middle or lower racks and red
wines on the upper racks (see Figure 4).
Keep wines that you plan to use for everyday drinking and
entertaining on the front half of the racks where labels are
completely visible. Place wines for aging or longer term
storing in the rear.
Figure 3
Roll-out Racks
The six (6) roll-out wine racks may be pulled out ap-
proximately 14 inches to facilitate adding or removing
bottles. Do NOT lean on or press down heavily on the
wine shelves. Doing so may damage the shelves and the
wine bottles stored on them. Pull the wine racks out gently
and carefully to minimize unsettling your wine collection.
AVOID pulling out more than one rack at any time to
maintain stability.
Single Bottle Racks
Since bottles are not stacked on top of each other, you can
easily view and access your inventory without disturbing
other bottles (see Figure 5).
Figure 4
Figure 5
4
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND CLEANING OF YOUR OUTDOOR WINE CELLAR
Using a small flat-blade screwdriver, gently lever the front
Condenser
section of the light tube down to allow it to be pulled clear
of the light housing.
The condenser tubing inside the cabinet does not require
frequent cleaning; however, satisfactory cooling depends
on adequate ventilation over the coils. Be sure that noth-
ing obstructs the required air flow openings in front of the
cabinet. At least once or twice a year, brush or vacuum lint
and dirt from the condenser for efficient performance by
unscrewing the grille on the bottom front of the cabinet.
Disconnect the two insulated electrical connectors from the
cabinet’s electrical cable and discard the old light tube.
Reconnect the electrical connector of the new light tube to
the cabinet’s electrical cable connectors. Make sure it is
secure and fully installed.
Cabinet
Carefully realign the light tube’s electrical terminal back
into the rear of the light enclosure channel making sure not
to crimp them. Gently insert the light tube along the length
of the light enclosure channel. Press the light tube gently
into the light enclosure channel. Only a small part of the
light tube should project below the ceiling of the wine cel-
lar. DO NOT USE A HAMMER TO FIT THE LIGHT TUBE.
The stainless steel cabinet can be washed with either
a stainless steel cleaner or a mild soap and water and
thoroughly rinsed with clear water. NEVER use abrasive
scouring cleaners.
Interior
Wash interior compartment with mild soap and water. Do
NOT use an abrasive cleaner, solvent, polish cleaner or
undiluted detergent.
Place the light tube terminal cover plate back in the original
position on the light enclosure’s flange. Reuse the original
two screws to secure it in place. Plug the wine cellar into
the electrical socket. Check to see if the light tube operates
properly. Your light tube’s replacement is complete.
Roll-out Racks
Tha racks may be cleaned with mild soap and water and a
soft cloth. Do NOT use any abrasive cleaners.
The light tubes are not covered by your warranty. Replace-
ment tubes can be obtained from your dealer or from
Marvel Industries.
Door Gasket
The vinyl gasket may be cleaned with mild soap and water,
a baking soda solution or a mild scouring powder.
In the Event of a Power Failure
Light Bulb Replacement
If a power failure occurs, try to correct it as soon as pos-
sible. Minimize the number of door openings while the
power is off so as not to adversely affect the unit’s tem-
perature.
WARNING! DISCONNECT THE POWER CORD BEFORE
ATTEMPTING LIGHT BULB REPLACEMENT. Failure to do so
may result in an electrical shock that could severely injure
you.
This product uses two, 6 watt light tubes to illuminate the
interior of the wine cellar. The light tube is a very reliable
electrical component, but should it not function properly,
please call the dealer you purchased your wine cellar from
for a replacement light tube. Use only an original equip-
ment light tube from your dealer or Marvel Industries.
Do NOT under any circumstance use a light tube that
exceeds 10 watts!
To replace a light tube, use a hex-head driver, remove the
two hex-head screws that hold a cover plate over the back
section of the light tube. Set the screws and cover plate
aside for reassembly later.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING YOUR OUTDOOR WINE CELLAR
Before Calling for Service
Before calling for service, check the troubleshooting table on this page. This
table lists possible problems that you can remedy without difficulty to avoid an
unnecessary service call.
PROBLEM
Odor in cabinet
POSSIBLE CAUSES/SOLUTIONS
1. Interior needs cleaning
1. Cabinet not level
Noisy operation
2. Weak floor
1. Cabinet not level
Cabinet vibrates
2. Weak floor
1. Tube burned out
Cabinet light not working
2. No power at outlet
1. “ON/OFF” button pressed
2. Power cord not plugged in
3. No power at electrical outlet
4. House fuse blown
Help Prevent Tragedies
Each year children die because they
climb inside a discarded refrigera-
tion product, get trapped inside and
suffocate. Take precautions to prevent
such tragedies by removing the door
or by taping or chaining it shut before
discarding.
Appliance will not run
Appliance runs too long
Moisture collects inside
1. Prolonged door openings
2. Control set too cold
3. Condenser needs cleaning
1. Too many door openings
2. Prolonged door openings
3. Hot, humid weather increases condensation
4. Control improperly set
1. Hot, humid weather increases condensation
(as humidity decreases, moisture will disappear)
Moisture collects on out-
side surface
2. Control improperly set
Interior too hot/too cold
1. Control improperly set
1. See “Warning Alarms” on page 3
2. See “Sentry System™ Control Quick
Reference”
3. Temperature alarm may occur after user
selected temperature set point changes in
excess of 10 degrees F, or during heavy usage
conditions. This is normal and not a fault of the
appliance. The Sentry System™ is monitoring
the duration of large swings in temperature to
protect your contents, and may alert you to this
event. See “Reset Alarms” on page 4.
Sentry System™
refrigeration monitor
activated
6
Download from Www.Somanuals.com. All Manuals Search And Download.
OBTAINING SERVICE FOR YOUR OUTDOOR WINE CELLAR
If You Do Need Service
How to Obtain Service
If you do need service, contact your dealer or Marvel Indus-
tries. In any correspondence, refer to the model number
and serial number of your unit which is located on the
upper left hand side of the wall liner. Retain your proof of
purchase. You may want to record these numbers in the
space below.
Your outdoor wine cellar requires little service because the
best and most up to date materials, equipment and qual-
ity methods are employed throughout the manufacturing
process.
If trouble occurs during normal operation, first check the
troubleshooting chart on the previous page to see if any
of these simple steps may correct the problem. If service
becomes necessary:
For Your Records
Date of Purchase
Dealer’s Name
1. If the product is within the first year warranty period,
please call Marvel Customer Service at 800.428.6644
for directions on how to obtain warranty coverage in
your area.
Dealer’s Address
Dealer’s City
Dealer’s State
2. If the product is outside of the first year warranty
period, Marvel Customer Service can provide recom-
mendations of service centers in your area. A listing
of authorized service centers is also available at www.
lifeluxurymarvel.com under the service and support
section.
3. In all correspondence regarding service, be sure to
give the model number, serial number, and proof of
purchase.
Dealer’s Zip
Appliance Serial Number
Model Number
Date Warranty Card Sent
(Must be within 10 Days of
Purchase)
4. Try to have information or description of the nature of
the problem, how long the unit has been running, the
room temperature, and any additional information that
may be helpful in quickly solving the problem.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
HOUSEHOLD PRODUCT WARRANTY
Entire Product
Parts or Service
Limited One Year Parts and Labor Warranty
Marvel warrants that it will supply all necessary parts and
labor to repair or replace in the end user’s home or office,
any component which proves to be defective in material
or workmanship, subject to the condition and exclusions
stated below, for a period of one year from the date of
purchase by the end user.
Not Supplied or Designated by Marvel
The above warranties also do not apply if:
•
•
•
The original bill of sale, deliver date, or serial number
cannot be verified.
Defective parts are not returned for inspection if so
requested by Marvel.
The refrigeration equipment is not in the possession of
the original end use purchaser.
Additional Second Through Fifth Year
Limited Parts Only Warrranty
During the four years following expiration of the one year
limited warranty, Marvel will supply replacement parts for
the hermetically sealed refrigeration system which consists
of the compressor, condenser, drier, accumulator, bypass
valve, connecting tubing and the evaporator that are
proven to be defective due to workmanship or materials
subject to the conditions and exclusions below.
The warranties set forth herein are the only warranties
extended by Marvel Industries. Any implied warranties, in-
cluding the implied warranty of merchantability, are limited
to the duration of these express warranties. In no event
shall Marvel Industries be liable for any consequential or
incidental damages or expenses resulting from breach of
these or any other warranties, whether express or implied.
The above warranties do not cover:
Some states do not allow the exclusion or limitation of con-
sequential damages or a limitation on how long an implied
warranty lasts, so the above exclusion or limitation may not
apply to you. This warranty gives you specific legal rights
and you may have other rights that may vary from state to
state.
•
•
Shipping costs of replacement parts or returned defec-
tive parts.
Customer education or instructions on how to use the
appliance.
•
•
Any content loss due to product failure.
Removal or installation.
No person, firm, or corporation is authorized to make any
other warranty or assume any other obligation for Marvel
Industries. These warranties apply only to products used in
any of the fifty states of the United States and the District of
Columbia.
Nor do the above warranties cover failure of this product or
its components due to:
•
•
Transportation or subsequent damages.
Commercial use or use other than normal household
or small office.
To obtain performance of this warranty, report any defects
to:
•
Improper installation, misuse, abuse, accident or
alteration, use on wiring not conforming to electrical
codes, low or high voltages, failure to provide neces-
sary maintenance, or other unreasonable use.
Marvel Industries
P.O. Box 997
Richmond, Indiana 47375-0997
Phone: 800.428.6644
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Marvel Industries
P.O. Box 997
Richmond, IN
47375-0997
800.428.6644
An AGA Company
41010819 Rev. B
03.03.08
All specifications and product designs subject to change without notice. Such revisions do not entitle
the buyer to corresponding changes, improvements, additions, replacements or compensation for
previously purchased products.
Download from Www.Somanuals.com. All Manuals Search And Download.
|