Marshall Electronics
1910 East Maple Ave.
El Segundo, CA 90245
SDI: 525i/60hz 4x3
Tel.: 800-800-6608 • 310-333-0606
Fax: 310-333-0688
Email: sales@lcdracks.com
OSD
Use SELECT to enable the On Screen Display
for input and function status
V-R84DP-SD Users Guide
Blue Only
SELECT to adjust SMPTE or split field color bars.
1. Allow monitor to warm up for 5-10 minutes minimum.
2. Display SMPTE color bars on monitor. Turn on off Color with control.
3. Find the PLUGE (superblack, black, and gray bars) at the lower right
of the pattern.
Adjust BRIGHTNESS until there is no difference visible between the super-
black and black bars, but is still visible.
4. Adjust CONTRAST control to achieve a balanced gray scale across
top bars.
5. Turn up CHROMA (color level) control until the two outermost bars
(white and blue appear to match in brightness.
6. NTSC Only -Adjust COLOR PHASE (tint or hue) control until the third
bar from the left (cyan) and the third bar from the right (magenta) appear to
match in brightness.
Product Overview
Features
1
2
Video - Screen Formats and Frame Rates
Electrical Specifications
Mechanical Specifications
Operational Setup
3
Warranty
12
4
5
6
Marshall Electronics warranties to the first consumer, that this V-R84DP-SD 8.4-inch TFT/LCD monitor will, under normal use, be free
from defects in workmanship and materials, when received in its original container, for a period of one year from the purchase date.
This warranty is extended to the purchasing end user only and proof of purchase is necessary to honor the warranty. If there is no proof
of purchase provided with a warranty claim, Marshall Electronics reserves the right not to honor the warranty set forth above. Therefore,
labor and parts may be charged to you.
Connectors
7
This warranty does not apply to product exterior and cosmetics. Misuse, abnormal service or handling, improper alterations or modifica-
tions in design or construction, voids this warranty. No sales personnel of the seller, nor any other person is authorized to make any war-
ranties other than those described above, or to extend the duration of any warranties on behalf of Marshall Electronics, beyond the time
period described above.
An extra note about LCD displays: It is considered normal for a minimal amount of pixels, not to exceed three, to fail on the periphery of
the display active viewing area. Marshall Electronics has the option to reserve service for display pixel failure if deemed unobtrusive to
effective use of the monitor by our technicians.
Faceplate Cleaning
8
9
10
11
12
Optional Accessories
Switch Settings, Adjustments and Indicators
Menu Functions
Due to constant effort to improve products and product features, specifications may change without notice.
Warranty
8
Download from Www.Somanuals.com. All Manuals Search And Download.
5
6
Mechanical Specifications
Switch Settings, Adjustments and Indicators
10
Dimensions
10.25”w x 7” h x 2.5” d (260.4mm x 215.9mm x 38.1mm)
V-R84DP-SD Weight
4 lbs (1.8 kg)
1 lbs (0.45kg)
V-PS12-5V-1 Power Supply Weight
Operational Setup
Tally Lamps
1. Unpack the V-R84DP-SD and accompanying V-PS12-5V-1 power supply. Physically inspect for any damage that may have
occurred during shipping. Should there be any damage, immediately contact Marshall Electronics at 800-800-6608.
If you are not located within the continental United States call +1 310-333-0606.
2. After inspection, install in your desired location of a standard EIA 19-inch equipment rack.
Adequate ventilation is required when installed to prevent possible damage to the V-R84DP-SD internal components.
3. Connect required cables for signal input and output. Please note that power must be applied to the V-R84DP-SD for all outputs
to be activated. All BNC connectors should be rated for 75Ω.
4. Plug the V-PS12-5V-1 power supply into the A.C. source
5. Attach twist lock power connection from V-PS12-5V-1 power supply to the back of the unit.
6. Turn on each of the V-R84DP-SD screens by depressing the power switch located on the front of the unit for each screen.
Connectors
7
* SDI Inputs comply to SMPTE-259M,SDI-270Mbs
* Component Inputs comply to SMPTE274M, 294M, 295M, 296M
* Composite Video Inputs comply to SMPTE-170M
* Tally lamps active when connected to ground
Active Outputs require
power to be applied
All input signals appear as
output signal
Analog output signals are
buffered and amplified
* Battery and External Power can not be used simultaneously
V-Mount Battery Adapter
See Optional Accessory
section for a selection of
batteries
Tally IN
DB-15 Female
Pin1-Yel
Pin9-
Pin2-Red
Pin3-Grn
Pin4-
Pin5-Gnd
Pin6-
Pin10-
Pin11-
Pin12-
Pin13-
Pin14-
Pin15-Gnd
12 VDC from
V-PS12-5V-1 power supply
Pin 1 - Neg
Dry Erase
Pin7-
Pin 2 - Pos
S-Video Out
4 Pin Din (Female)
Pin1 - GND
Pin2 - GND
Pin3 - Yout
Pin4 - Cout
Screen aspect ratio switch 4:3 or 16:9 selector and indicators
Image Adjustment Controls
Note: Tint only functions when NTSC
Video or S-Video are selected
S-Video In
4 Pin Din (Female)
Pin1 - GND
Pin2 - GND
Pin3 - Yin
Pin4 - Cin
DVI-Connector
Pin#
Pin#
Signal
Signal
1
2
3
T.M.D.S DATA 2-
T.M.D.S DATA 2+
T.M.D.S DATA 2/4
SHIELD
16
17
18
HOT PLUG DETECT
T.M.D.S DATA 0-
T.M.D.S DATA 0+
4
T.M.D.S DATA 4-
19
T.M.D.S DATA 0/5
SHIELD
T.M.D.S DATA 5-
T.M.D.S DATA 5+
T.M.D.S CLOCK
SHIELD
4:3 Aspect
16:9 Aspect
5
6
7
T.M.D.S DATA 4+
DDC CLOCK
DDC DATA
20
21
22
VGA/XGA Connector
PIN#
SIGNAL
RED
PIN#
9
SIGNAL
NC
NC
NC
NC
HSYNC
VSYNC
NC
1
2
3
4
5
6
7
8
8
9
10
11
ANALOG VERT. SYNC
T.M.D.S DATA 1-
T.M.D.S DATA 1+
T.M.D.S DATA 1/3
SHIELD
T.M.D.S DATA 3-
T.M.D.S DATA 3+
+5V POWER
23
24
T.M.D.S CLOCK+
T.M.D.S CLOCK-
GREEN
BLUE
NC
GND
RED SHIELD
GREEN SHIELD
BLUE SHIELD
10
11
12
13
14
15
C1
ANALOG RED
12
13
14
15
C2
C3
C4
C5
ANALOG GREEN
ANALOG BLUE
ANALOG HORZ SYNC
ANALOG GROUND
GND
MarshallElectronics
V-R84DP-SD Users Guide
3
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 2 / Video Signals Displayed via DVI and YPrPb connections
(x=not available) (HDMI requires adapter to DVI)
Table 3 / Video Signals Displayed via SDI
SDI
9
Optional Accessories
Y Pr Pb
DVI
Input Signal Type
and aspect
Input Signal Type and aspect
4x3
16x9
4x3
16x9
4:3
Y
16:9
Y
Sun Hood
V-H900
Use for viewing in bright lighting or outdoors
Use with Anton Bauer D-type connection
720 x 486 60i
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
x
x
x
x
NTSC (720x486i 60Hz)
PAL (720 x 576i 50Hz)
720 x 576 50i
Y
Y
Power Adapter Cable
Power Adapter Cable
V-PAC-D
1280 x 720 60P
1280 x 720 50P
1280 x 720 30P
1280 x720 29.97P
1280 x720 25P
1280 x 720 24P
1280 x 720 23.98P
1920 x 1080 60i
1920x1080 59.94i
1920 x 1080 50i
1920 x 1080 30P
1920x1080 29.97P
1920 x 1080 25P
1920 x 1080 24P
1920 x 1080 24Psf
Y
Y
x
Y
Y
x
Table 1 / Computer Signals Displayed via DVI and VGA connector
x
x
V-PAC-XLR
V-DV-PWR1
Use with 4 Pin XLR connections
DVI-D
VGA
16x9
x
x
Input Signal Type
and aspect
4x3
16x9
4x3
x
x
Uses 2 Sony DVCam/HDV FP-Type batteries.
When used with monitor power supply, can
charge batteries plus operate monitor
640 x 480 60Hz
640 x 480 75Hz
640 x 480 85Hz
800 x 600 60Hz
800 x 600 75Hz
800 x 600 85Hz
1024 x 768 60Hz
1024 x 768 75Hz
1024 x 768 85Hz
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
x
x
Battery Adapter
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Use to power Marshall Electronics monitors
that have V-Mount plate with Anton Bauer Gold
Mount battery.
V-mount to Anton Bauer
adapter
V-ABA-01
2-channel sequential charger with a built-in 60W
power supply. Charges 2 ENDURA E series bat-
teries in fewer than 5 hours. One 10’ XLR cable
included. Weighs only 2 lbs
Sequential 2 channel
charger
IDX-VL-2Plus
IDX-VL-4
Economically charges 4 ENDURA E series bat-
teries in under 6 hours using Full Power Charge
(FPC) method
8
Sequential 4 channel
charger
Faceplate Cleaning
Faceplate Cleaning
When cleaning the faceplate it is very important to use non-abrasive and ammonia free cleaning agents and a clean micro fiber cloth. Do not use paper
towels. Paper towel fibers are coarse and may scratch the surface of the Polycarbonate faceplate. Paper towels may also leave streaks on the surface.
Antistatic and fingerprint resistant cleaning agents are recommended.
Wash protective cover with a solution of mild soap or detergent and lukewarm water. Use a clean soft cloth, applying only light pressure. Rinse with clean
water and dry by blotting with a damp cloth or chamois. Grease, oil or tar may be removed with a good grade of hexane, aliphatic naphtha, or kerosene.
These solvents may be obtained at a paint or hardware store and should be used in accordance with manufacturer’s recommendations.
DO NOT USE: window cleaning sprays, kitchen scouring compounds or solvents such as acetone, gasoline, benzene, alcohol, carbon tetrachloride, or
lacquer thinner. These can scratch the sheet’s surface and/or weaken the sheet causing small surface cracks called “crazing.”
Faceplate Dusting
Dust with a soft, damp cloth or chamois. Dry or gritty cloths may cause surface scratches and create a static electric charge on the surface. Neutralizing
static electricity effects by using recommended cleaning and polishing practice.
Faceplate Polishing
Protect and maintain surface gloss by occasional polishing with a good plastic cleaner and polish. Apply a thin, even coat with a soft clean cloth and pol-
ish lightly with cotton flannel. Then wipe with a damp cloth to help eliminate electrostatic charges that can attract dust particles
Marking on the Faceplate
Charges 4 ENDURA E series batteries in 2.5
hours or less
Simultaneous 4 channel
charger
IDX-VL-4S
55 W Lithium Battery
IDX-E7S
IDX-E7
V-Mount battery pack with 3 LED power Indicator
V-Mount Battery Pack with PowerLink includes
accurate Power Status Display and supports
Digi-View
55 W Lithium Battery
with Power Link
Use SHARPEE or equivalent marker. Clean as per instructions with an ammonia free cleaning agent.
Recommended Anti-Static Cleaners and Polishes
210 Plastic Cleaner & Polish and 210 Plus Cleaner
Sumner Laboratories
Plexus Plastic Cleaner
Plexus
638 Lindero Canyon Rd. #371
Agoura, CA 91301
800-405-6495
82 W Lithium Battery
IDX-E10S
IDX-E10
V-Mount battery pack with 3 LED power Indicator
Exair Corporation
1250 Century Circle North
Cincinnati, OH 45246-3309
513-671-3322
Fax : 513-671-3363
186 Lincoln Street
Boston, MA 02111
617-542-8656 / Fax: 617-482-9001
V-Mount Battery Pack with PowerLink includes
accurate Power Status Display and supports
Digi-View
82 W Lithium Battery
with Power Link
Fax: 818-879-0697
Crystalclean
NOVUS #1 Plastic Clean and Shine
NOVUS, Inc.
12800 Highway 13 South, Suite 500
Savage, MN 55378
800-548-6872 ext.451
Fax: 952-946-0435
The Simco Industrial Static Control
An Illinois Tool Works Co.
2257 North Penn Road
Hatfield, PA 19440-1998
800-203-3419
Discovery Plastics
3700 Western Way, NE
Millersburg, OR 97231
541-926-2900 / Fax: 541-967-8441
Digital to Analog
Converter
BC-0301-10
Converts SDI to analog Composite
215-822-2171
Fax: 215-822-3795
Attaches to any side for mount to ¼-20 threaded
component
Mounting Plate
Cleaning Wipes
VP-LCD70-TMB-02
Scotch-Brite High Performance Cloth
3M Stationery & Office Supplies Div.
3M Center
St. Paul, MN 55144-1000
877-362-5684
Fax: 651-733-0382
20/20 Plastic-Cleaner
Craftics, Inc.
PO Box 91930
Albuquerque, NM 87199
(505) 338-0005
Package of 10 non-toxic, antistatic, alcohol and
ammonia free cleaning wipes.
V-HWP-K
Marshall Electronics
V-R84DP-SD Users Guide
5
4
Download from Www.Somanuals.com. All Manuals Search And Download.
|
La Crosse Technology Clock 616 146A User Manual
LevelOne Network Router WBR 5400 User Manual
LG Electronics Washer 2P~32P User Manual
Life Fitness Home Gym G5 001 User Manual
Logitech Headphones BH940 User Manual
Lucent Technologies Network Card Lucent Network Gateway User Manual
Makita Power Hammer HR4013C User Manual
Marantz Stereo Receiver SR3001 User Manual
Melissa Toaster 243022 User Manual
Meridian America Portable Speaker DSP33C User Manual