CONGRATULATIONS!
Your purchase of an M&S Systems music and communications system is an investment that will provide years of enjoyment and service
for your customer.
M&S audio products are backed with more than 40 years of experience in the design and manufacture of precision acoustical equipment
for the home. To ensure that your customer receives the high-quality music and voice reproduction that the system is designed to deliver,
it is important that each step of the installation be done carefully. If you follow the step-by-step illustrated instructions below, the result will
be a successful professional quality installation. In the event you need troubleshooting assistance, please call our technical staff at 1-800-366-
9422.
INSTALLATION INSTRUCTIONS
FINISH-OUT MC111M/DM SYSTEM
Toolsrequired:Phillipsscrewdriver#2,Standardflatscrewdriver#1,
wire stripper/cutter.
REMOTE DOOR RELEASE STATIONS
N15D/N35D SERIES
The finish-out installation should be made after the application of wall
covering material.
At each door release control
station
location,
strip
approximately 4 inches of
jacket (MS4XSC) from wires
&
DOs
DONT's
and
separate
colored
conductorsfromoneanother.
Strip 1/2 inch of insulation
fromeachconductorincluding
theVM127X.Cutoffthedrain
wire from the Black/White
pair. Connect the Red wire
from the volume control
switch to the Red wire on the
VM127X. Connect the White
wire from the volume control
to the White wire on the VM127X.
ꢀ USE ONLY M&S SYSTEMS BRAND CABLE as
called out in these instructions. The cable is designed and
constructed with electrical specifications necessary for proper
audio performance. IMPORTANT: THE USE OF NON M&S
SYSTEMS’ BRAND CABLE OR CABLE SUBSTITUTION WILL
VOID PRODUCT WARRANTY. Note: All M&S Systems’ cable
has M&S Systems and the part number printed on it!
ꢀ DO NOT power up master until all remote stations and
Figure 4
speakers are connected.
ꢀ DO ensure that all rough-in instructions (literature number
115741) have been followed before power is applied to
system.
SATELLITE VOLUME CONTROL
MVC1 SERIES
ꢀ DO NOT SPLICE CABLES. Splices are unreliable and
defeat the signal isolation properties of the cable.
ꢀ DO NOT COIL OR BUNDLE the MS4X cable. This will
At each satellite control station
location, strip approximately 4
inches of jacket (MS4XSC and
MS2SXSC) from wires and
separate colored conductors from
one another. Strip 1/2 inch of
insulation from each conductor.
Connect drain wires together
frombothcablesusingawirenut
(MS4XSC only). Wire nut each
colored conductor to its
cause electronic feedback.
ꢀ If extra cables have been run for possible future speaker
additions, care must be taken that these cables do not get
connected to the master unit. Unterminated cables (no
station) connected to the master unit may cause electronic
feedback that will damage the master unit.
ꢀ DO NOT overtighten the screws for the remote stations or
the master as the plastic face panels may crack or strip out.
Figure 5
REMOTE STATIONS N14/N35 SERIES
respective wire as shown in figure 5. Connect Blue and Violet wires
to the corresponding terminals of the satellite speaker(s). Mount
the volume control to the single gang box using the two screws
provided with the volume control.
At each remote station location,
strip approximately 4 inches of jacket
(MS4XSC) from wire and separate
the colored conductors from one
another. Strip 1/2 inch of insulation
PATIO STATIONS NW14/NW35 SERIES
from
each
as
Figure 1
conductor
At each remote station
l o c a t i o n , s t r i p
approximately 4 inches
ofjacket(MS4XSC)from
wire and separate
colored conductors from
one another. Strip 1/2
inch of insulation from
each conductor. Cut
eachshielddrainwireat
theshieldfoiltoprevent
shown in figure
1. Cut each
shield drain wire
at the shield foil
to prevent them
from
each
touching
other
(MS4XSC only).
Connect each
c o l o r e d
conductor to its
Figure 2
Figure 3
themfromtouchingeach
other (MS4XSC only).
Connect each colored conductor together using wire nuts as shown
in figure 6. Mount the patio station to housing using the two screws
provided with the station.
respective screw terminal as shown in figure 2. Mount each remote
station to it’s mounting ring using the two screws provided with each
station as shown in figure 3.
Figure 6
Download from Www.Somanuals.com. All Manuals Search And Download.
|