CLUB SERIES 45 DEGREE
BACK EXTENSION
ASSEMBLY INSTRUCTIONS
Part # 7199901
RevA.
1
Revision:10/19/01
Download from Www.Somanuals.com. All Manuals Search And Download.
7 3/8 X 3” BOLT
11
3/8” LOW
HEIGHT LOCK
NUT
10 3/8 X 3-3/4” BOLT
12
3/8” SAE
WASHER
6 3/8 X 2-3/4” BUTTON HEAD BOLT
8 5/16 X 1/2” SHOULDER HEAD BOLT
14
3/8” BLACK SAE
WASHER
13
RH
9
LOCK
WASHER
WASHER
15
RH CAP
(WHITE/PLATINUM)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 1
1
11
13
12
3
3/8 X 3-3/4” 10
15
STEP 1:
• SECURELY assemble the two SUPPORTS (3) to the FRAME (1) using eight RH CAPS (15), four 3/8 X 3-3/4” BOLTS (10),
eight 3/8” SAE WASHERS (12), eight 3/8” RH WASHERS (13) and four 3/8” LOW HEIGHT LOCK NUTS (11) as shown in
FIGURE 1.
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
4
4
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 2
2
SPRING PIN
1
6 3/8 X 2-3/4” BUTTON HEAD
14 BLACK
4
13
12
11
15
STEP 2:
• Pull back the SPRING PIN on the FRAME (1) and insert the HIP PAD ADJUST (2) as shown in FIGURE 2.
• SECURELY assemble the FORMED ANGLE (4) to the FRAME (1) using two 3/8 X 2-3/4” BUTTON HEAD BOLTS (6), two 3/8”
BLACK SAE WASHERS (14), two 3/8” RH WASHERS (13), two 3/8” SAE WASHERS (12), two 3/8” LOW HEIGHT LOCK
NUTS (11) and two RH CAPS (15) as shown in FIGURE 2.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 3
2
9
8 5/16 X 1/2”
SHOULDER
BOLT
STEP 3:
• SECURELY assemble one 5/16 X 1/2” SHOULDER BOLT (8) and one 1/4” LOCK WASHER (9) to the HIP PAD ADJUST (2) as
shown in FIGURE 3.
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
6
4
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 4
3”
5
15
13
3/8 X 3” 7
2
STEP 4:
• SECURELY assemble the two HIP PADS (5) to the HIP PAD ADJUST (2) using two RH CAPS (15), two 3/8 X 3” BOLTS (7) and
two 3/8” RH WASHERS (13) as shown in FIGURE 4. (Note the the direction of the hole pattern on pad.)
7
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION-PLEASE READ
There is a risk assumed by individuals who use this type of equipment. To minimize risk, please
follow these rules:
1. Inspect equipment daily. Tighten all loose connections and replace worn parts immediately.
Failure to do so may result in serious injury.
2. Do not allow minors or children to play on or around this equipment.
3. Exercise with care to avoid injury.
4. Consult your physician before beginning any exercise program.
WARRANTY INFORMATION
10YEARS
3 YEARS
1 YEAR
STRUCTURUAL FRAME
PILLOW BLOCKS, PULLEYS, WEIGHT PLATESAND GUIDE RODS
CABLES
90 DAYS
UPHOLSTERY
PREVENTATIVE MAINTENANCE TIPS
Action
DAILY WEEKLY QUARTERLY BI-ANNUALLY AS NEEDED
CLEAN
Upholstery
Guide Rods
Hand Grips
X
X
X
INSPECT
Visual Overall
Cables
Hardware
Frame
X
X
X
X
X
Hand Grips
LUBRICATE
Guide Rods
X
Clean:
• Upholstery with mild soap and water.
• Guide rods with a cotton cloth.
• Hand grips with mild soap and water.
• Frame damage can be repaired with touch-up paint can be purchased from your LifeFitness customer service representative at
(800)351-3737.
Inspect:
• Cables for wear or damage and proper tension (should not exceed 3/4” deflection.) Pay close attention at bends and attachment
points.
• Hardware should be checked for looseness. Tighten as required.
• Frames should be inspected for wear or damage.
• Hand Grips should be checked for wear or damage
Lubricate:
• Lube the Guide Rods. Apply the lubricant to a cotton cloth, then run the cotton cloth up and down the guide rods as needed. Do not
spray lubricant directly on the Guide Rods.
Thank you for purchasing the LifeFitness CLUB SERIES 45 DEGREE BACK EXTENSION. If unsure of
proper use of equipment, call your local LifeFitness distributor or call the LifeFitness customer service
department at (800) 351-3737.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
|