INSTRUCTION MANUAL
Screwdriver
6827
002606
DOUBLE INSULATION
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
And are manufactured in accordance with the following
standards or standardised documents:
EN60745
The technical documentation is kept by our authorised
representative in Europe who is:
6.
7.
Do not expose power tools to rain or wet
conditions. Water entering power tool will
increase the risk of electric shock.
Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords
increase the risk of electric shock.
a
Makita International Europe Ltd,
Michigan, Drive, Tongwell,
Milton Keynes, MK15 8JD, England
8.
9.
When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
If operating a power tool in a damp location is
unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
30th January 2009
000230
Tomoyasu Kato
Director
Makita Corporation
3-11-8, Sumiyoshi-cho,
Anjo, Aichi, JAPAN
10. Use of power supply via a RCD with a rated
residual current of 30mA or less is always
recommended.
Personal safety
GEA005-3
11. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or
General Power Tool Safety
Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
medication.
A
moment of inattention while
operating power tools may result in serious
personal injury.
12. Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
13. Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools
with your finger on the switch or energising power
tools that have the switch on invites accidents.
14. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
15. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
16. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing, and gloves
away from moving parts. Loose clothes,
jewellery or long hair can be caught in moving
parts.
17. If devices are provided for the connection of
dust extraction and collection facilities,
ensure these are connected and properly used.
Use of dust collection can reduce dust-related
hazards.
Save all warnings and
instructions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Work area safety
1.
2.
Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
3.
Electrical safety
4.
Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
5.
Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of
electric shock if your body is earthed or grounded.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Power tool use and care
2.
Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
18. Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
19. Do not use the power tool if the switch does
not turn it on and off. Any power tool that cannot
be controlled with the switch is dangerous and
must be repaired.
3.
4.
5.
Hold the tool firmly.
Keep hands away from rotating parts.
Do not touch the bit or the workpiece
immediately after operation; they may be
extremely hot and could burn your skin.
20. Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this
instruction manual may cause serious personal
injury.
21. Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are
dangerous in the hands of untrained users.
22. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
23. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
24. Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the power
tool for operations different from those intended
could result in a hazardous situation.
FUNCTIONAL DESCRIPTION
CAUTION:
•
Always be sure that the tool is switched off and
unplugged before adjusting or checking function on
the tool.
Depth adjustment
1. Pointer
2. Locator
1
2
3. Front cap
4. Adjusting ring
3
4
Service
002614
25. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
When you wish to drive self drilling screws, etc., adjust
the depth as follows. Turn the locator to adjust the depth.
Initially, adjust the locator to create
a
distance of
26. Follow instruction for lubricating and
changing accessories.
27. Keep handles dry, clean and free from oil and
approximately 1 mm from the tip of the front cap (which
works in conjunction with the locator) to the base of the
screw head. One full turn of the locator equals 1 mm
change in depth.
grease.
GEB017-4
After adjusting the locator, turn the adjusting ring so that
the 6" mark is aligned with the pointer on the gear
housing. Drive a trial screw into your material or a piece
of duplicate material. If the depth is not suitable for the
screw, continue adjusting until the proper depth setting is
obtained.
SCREWDRIVER SAFETY
WARNINGS
1.
Hold power tool by insulated gripping
surfaces, when performing an operation where
the fastener may contact hidden wiring or its
own cord. Fasteners contacting a "live" wire may
make exposed metal parts of the power tool "live"
and could give the operator an electric shock.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Reversing switch action
1mm
1
1. Reversing
switch lever
A
B
004336
002635
1mm
CAUTION:
•
•
Always check the direction of rotation before
operation.
Use the reversing switch only after the tool comes
to a complete stop. Changing the direction of
rotation before the tool stops may damage the tool.
This tool has a reversing switch to change the direction
of rotation. Move the reversing switch lever to
004337
the
position (A side) for clockwise rotation or
the position (B side) for counterclockwise rotation.
Adjusting the fastening torque
1. Locator
Switch action
1. Switch trigger
2. Lock button
1
2
3
2. Adjusting ring
3. Pointer
2
1
002628
002642
CAUTION:
•
Before plugging in the tool, always check to see
that the switch trigger actuates properly and
returns to the "OFF" position when released.
When you wish to drive machine screws, wood screws,
hex bolts, etc. with the predetermined torque, adjust the
fastening torque as follows.
To start the tool, simply pull the switch trigger. Tool
speed is increased by increasing pressure on the switch
trigger. Release the switch trigger to stop.
For continuous operation, pull the switch trigger and
then push in the lock button.
The fastening torque may be adjusted by turning the
adjusting ring. Before turning the adjusting ring, turn the
locator in the direction of the arrow as far as it will go
without forcing. The torque is increased by turning the
adjusting ring in the direction of the arrow and
decreased by turning it in the opposite direction. Align
the number 1 on the adjusting ring with the pointer on
the gear housing. Drive a trial screw into your material or
a piece of duplicate material. If the fastening torque is
not suitable for the screw, continue adjusting until the
proper torque is obtained.
To stop the tool from the locked position, pull the switch
trigger fully, then release it.
NOTE:
•
Even with the switch on and motor running, the bit
will not rotate until you fit the point of the bit in the
screw head and apply forward pressure to engage
the clutch.
CAUTION:
•
The adjusting ring should be turned only within the
numbered range. It should not be forced beyond
this range.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Hook
OPERATION
1. Hook
A
1
002646
002675
Fit the screw on the point of the bit and place the point of
the screw on the surface of the workpiece to be fastened.
Apply pressure to the tool and start it. Withdraw the tool as
soon as the clutch cuts in. Then release the switch trigger.
B
CAUTION:
•
When fitting the screw onto the point of the bit, be
careful not to push in on the screw. If the screw is
pushed in, the clutch will engage and the screw will
rotate suddenly. This could damage a workpiece or
cause an injury.
002647
The hook is convenient for temporarily hanging the tool.
When using the hook, pull it out in "A" direction and then
push it in "B" direction to secure in place.
When not using the hook, return it back to its initial
position by following the above procedures in reverse.
•
Make sure that the bit is inserted straight in the
screw head, or the screw and/or bit may be
damaged.
MAINTENANCE
ASSEMBLY
CAUTION:
•
Always be sure that the tool is switched off and
unplugged before attempting to perform inspection
or maintenance.
CAUTION:
•
Always be sure that the tool is switched off and
unplugged before carrying out any work on the
tool.
To maintain product SAFETY and RELIABILITY, repairs,
carbon brush inspection and replacement, any other
maintenance or adjustment should be performed by
Makita Authorized Service Centers, always using Makita
replacement parts.
Installing or removing the bit
To remove the bit, first pull the front cap off and then pull
the bit out firmly.
ACCESSORIES
CAUTION:
•
These
accessories
or
attachments
are
recommended for use with your Makita tool
specified in this manual. The use of any other
accessories or attachments might present a risk of
injury to persons. Only use accessory or
attachment for its stated purpose.
002655
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
To install the bit, insert it into the tool as far as it will go
and then replace the front cap.
•
•
•
•
Phillips bit
Magnetic socket bit
Front cap
Plastic carrying case
6
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Makita Corporation Anjo, Aichi, Japan
884379F916
Download from Www.Somanuals.com. All Manuals Search And Download.
|