Download from Www.Somanuals.com. All Manuals Search And Download.
PRECAUTIONS
Before you read anything else, please observe the following:
Warning!
The manufacturer DOES NOT represent this unit to be waterproof. To reduce the risk of fire, electrical shock, or
damage to the unit, DO NOT expose this to rain or moisture.
Rechargeable Nickel-Cadmium Battery Warning
& This equipment contains a rechargeable nickel-cadmium battery.
& Cadmium is a chemical known to the State of California to cause cancer.
& The rechargeable nickel-cadmium battery contained in this equipment may explode if disposed of in a fire.
& Do not short-circuit the battery.
& Do not charge the rechargeable nickel-cadmium battery used in this equipment in any charger other than the
one designed to charge this battery as specified in the owner's manual. Using another charge may damage the
battery or cause the battery to explode.
RECHARGEABLE NICKEL-CADMIUM BATTERIES MUST BE RECYCLED OR
DISPOSED OF PROPERLY
May be covered under one or more of the following U.S. patents:
4,511,761
5,434,905
5,661,780
5,787,356
5,929,598
4,523,058
5,491,745
5,663,981
5,838,721
5,930,720
4,595,795
5,533,010
5,671,248
5,864,619
5,960,358
4,797,916
5,574,727
5,717,312
5,893,034
5987,330
5,381,460
5,650,790
5754,407
5,912,968
5,426,690
5,650,269
5,768,345
5,915,227
©2000 Memorex is a registered trademark of Memorex Telex N.V.
All rights reserved. Printed in China UCZZ01237BC
Download from Www.Somanuals.com. All Manuals Search And Download.
Color profile: Disabled
Composite Default screen
IMPORTANT SAFETY INSTRUCTIONS
When using your telephone equipment, these basic safety precautions should always be followed
to reduce the riskof fire, electrical shock, and injury to persons:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product.
3. Unplug this product from the wall outlet before cleaning. Use a dry cloth for cleaning without
liquid or aerosol cleaners.
4. Do not use this product near water; for example, near a bath tub, wash bowl, kitchen sink or
laundry tub, in a wet basement, or near a swimming pool.
5. Do not place this product on an unstable cart, stand, or table. The telephone may fall, causing
serious damage to the unit.
6. Slots and openings in the cabinet and the backor bottom are provided for ventilation. To protect
the product from overheating, these openings must not be blocked or covered. This product
should never be placed near or over a radiator or heat register. This product should not be
placed in a built-in installation unless proper ventilation is provided.
7. This product should be operated only from the type of power source indicated on the marking
label. If you are not sure of the type of power supply to your home, consult your dealer or local
power company.
8. Do not allow anything to rest on the power cord. Do not locate this product where the cord will
be damaged by persons walking on it.
9. Do not overload wall outlets and extension cords, as this can result in the riskof fire or
electrical shock.
10. Never push objects of any kind into this product through cabinet slots, as they may touch
dangerous voltage points or short out parts that could result in a riskof fire or electric shock.
Never spill liquid of any kind on the product.
11. To reduce the riskof electric shock, do not disassemble this product. Take it to qualified service
personnel when service or repair workis required. Opening or removing covers may expose you to
dangerous voltages or other risks. Incorrect reassembly can cause electric shock when the
appliance is subsequently used.
12. Unplug this product from the wall outlet and refer servicing to qualified service personnel under
the following conditions:
A.
B.
C.
When the power supply cord is damaged or frayed.
If liquid has been spilled into the product.
If the product has been exposed to rain or water.
i
F:...MPH6929ENG.VP
Thu Jun 14 15:46:54 2001
Download from Www.Somanuals.com. All Manuals Search And Download.
Color profile: Disabled
Composite Default screen
D.
If the product does not operate normally when following the operating instructions.
(Adjust only those controls that are covered by the operating instructions. Improper
adjustment of other controls may result in damage and will often require extensive repair work
by a qualified technician.)
E.
F.
If the product has been dropped or the cabinet has been damaged.
If the product exhibits a distinct change in performance.
13. Do not use the telephone to report a gas leakin the vicinity of the leak.
M Additional Battery Safety Precautions
Caution! To reduce the riskof fire or injury to persons by the battery, read and follow these
instructions:
1. Use only the appropriate type and size battery packspecified in the reference guide.
2. Do not dispose of the battery packin a fire. The cell may explode.
3. Do not open or mutilate the battery pack. Released electrolyte is corrosive and may cause
damage to the eyes or skin. It may be toxic if swallowed.
4. Exercise care in handling the battery in order not to short the battery with conducting materials
such as rings, bracelets, and keys. The battery or conductor may overheat and cause burns.
5. Charge the battery packprovided with or identified for use with this product only in accordance with the
instructions and limitations specified in the reference guide provided for this product.
6. Observe proper polarity orientation between the battery packand battery charger.
M Cordless Telephone Privacy
Note!
Cordless telephones are radio devices. Communications between the handset and
base of your cordless telephone are accomplished by means of radio waves which are broadcast
over the open airways. Because of the inherent physical properties of radio waves, your
communications can be received by radio receiving devices other than your own cordless
telephone unit. Consequently, any communications using your cordless telephone may not be
private.
ii
F:...MPH6929ENG.VP
Thu Jun 14 15:46:54 2001
Download from Www.Somanuals.com. All Manuals Search And Download.
Color profile: Disabled
Composite Default screen
WELCOME
Congratulations on your purchase of the Memorex MPH6929 cordless
telephone and answering system. This phone is designed and engineered
to exacting standards for reliability, long life, and outstanding
performance.
FEATURES
• 900 MHz Extended Range Technology
• Integrated Telephone Answering Device (ITAD)
• 10 Number Memory Dialing
• 3 Instant Dial Priority Keys
• 32 Digit Redial
• Flash and Pause
• Pulse/Tone Dialing
• Page/Find
• 7 Hour TalkTime
• Handset Earpiece and Ringer Volume Control
• Hearing Aid Compatible
The MPH6929 features include Instant Talk and Auto Disconnect. Instant Talk
allows you to answer a call by just removing the handset from the base so you
don’t have to waste time pushing buttons or flipping switches. Auto Disconnect
allows you to hang up by simply returning the handset to the base.
The Mega Clear Plus true compander circuitry virtually eliminates
background noise. This innovative technology, together with 40 different
channels, provides you with the best possible reception during all your
conversations.
To protect you against misbilled calls which might result from your phone
being activated by other equipment, the MPH6929 has a digital security
system which automatically selects one of over 65,000 digital security codes
for the handset and base. Also, the MegaSecure feature electronically locks
your phone when the handset is in the base.
To get the most from your phone, please read this owner’s manual thoroughly.
Also, be sure to complete the product registration form and mail it in.
Memorex® is a registered trademarkof the Memorex Telex N.V.
1
F:...MPH6929ENG.VP
Thu Jun 14 15:46:55 2001
Download from Www.Somanuals.com. All Manuals Search And Download.
Color profile: Disabled
Composite Default screen
INCLUDED IN YOUR PACKAGE
To get the most from your
phone, please read this
owner’s manual thoroughly.
Also be sure to complete
and mail the product
registration form.
Handset
AC Adapter
Base
Rechargeable Battery
(Located inside handset)
Telephone Cord
Wall Mount Adapter
Also included:
• This Owner’s Manual
2
F:...MPH6929ENG.VP
Thu Jun 14 15:47:00 2001
Download from Www.Somanuals.com. All Manuals Search And Download.
Color profile: Disabled
Composite Default screen
IMPORTANT ELECTRICAL CONSIDERATIONS
Unplug all electrical appliances when you know an electrical storm is
approaching. Lightning can pass through your household wiring and
damage any device connected to it. This phone is no exception.
WARNING
Please do not attempt
to unplug any
The FCC Wants You To Know
appliance during an
electrical storm.
Changes or modifications to this product not expressly approved by the
manufacturer, or operation of this product in any way other than as
detailed by the reference guide, could void your authority to operate
this product. The equipment cannot be used on public coin phone
service provided by the telephone company. Connection to party line
service is subject to state tariffs. (Contact the state public utility
commission, public service commission or corporation commission
for information.)
Range
Your new phone is designed to achieve the maximum possible range by
transmitting and receiving according to the highest specifications set
forth by the FCC. We have rated this phone to operate at a maximum
distance with the qualification that the range depends upon the
environment in which the telephone is used. Many factors limit range,
and it would be impossible to include all the variables in our rating.
The Maximum Range rating of this phone is meant to be used as a
means of comparison against other range claims.
Telephone Line Problems
The FCC has granted the telephone company the right to disconnect
service in the event that your phone causes problems on the telephone
line. Also, the telephone company may make changes in facilities and
services which may affect the operation of your unit. However, your
telephone company must give adequate notice in writing prior to such
actions to allow you time for making necessary arrangements to
continue uninterrupted service.
If you are having trouble with your telephone service, you must first
disconnect your phone to determine if it is the cause of your problem.
If you determine that it is the cause, you must leave it disconnected
until the trouble has been corrected.
3
F:...MPH6929ENG.VP
Thu Jun 14 15:47:01 2001
Download from Www.Somanuals.com. All Manuals Search And Download.
Color profile: Disabled
Composite Default screen
Radio Interference
Radio interference may occasionally cause buzzing and humming in
your cordless handset, or clicking noises in the base. This interference
is caused by an external source such as a TV, refrigerator, vacuum
cleaner, fluorescent lighting, or electrical storm. Your unit is NOT
DEFECTIVE. If these noises continue and are too distracting, please
checkaround your home to see what appliances may be causing the
problem. In addition, we recommend that the base not be plugged into
a circuit that also powers a major appliance because of the potential for
interference. Be certain the antenna is kept in the vertical position.
In the unlikely event that you consistently hear other voices or
distracting transmissions on your phone, you may be receiving radio
signals from another cordless telephone or other source of interference.
If you cannot eliminate this type of interference, you need to change to
a different channel.
Finally, it should be noted that some cordless telephones operate at
frequencies that may cause interference to nearby TVs and VCRs. To
minimize or prevent such interference, the base of the cordless
telephone should not be placed near or on top of a TV or VCR. If
interference is experienced, moving the cordless telephone farther
away from the TV or VCR will often reduce or eliminate
the interference.
More Than One Cordless Telephone
If you want to use more than one cordless telephone in your home,
they must operate on different channels. Press the channel key to select
a channel that provides the clearest communication.
4
F:...MPH6929ENG.VP
Thu Jun 14 15:47:01 2001
Download from Www.Somanuals.com. All Manuals Search And Download.
Color profile: Disabled
Composite Default screen
INSTALLATION CONSIDERATIONS
Selecting a Location
Before choosing a location for your new phone, there are some
important guidelines you should consider:
• The location should be close to both a phone jackand continuous
power outlet. (A continuous power outlet is an AC outlet which
does not have a switch to interrupt its power.)
• Keep the base and handset away from
sources of electrical noise such as motors
or fluorescent lighting.
• Be sure there is sufficient space to fully
extend the base antenna.
• The base can be placed on a deskor
tabletop or mounted on a standard AT&T
or GTE wall plate.
• You should charge your new phone for 15-
20 hours before completing the installation or using the handset.
Telephone Line Outlets
There are two types of phone outlets:
M Modular Jack
Most phone equipment available now uses modular jacks. Phone cords
are fitted with a molded plastic connector which plugs into this type of
jack. If you do not have modular phone jacks, contact your local
telephone company for information about their installation.
M Hardwired Jack
Some equipment is wired directly to a phone jack, and these types of
installations require a modular jackconverter. This type of installation
is not difficult; however, you should contact your local telephone
dealer or a telephone supply store for advice about the proper adapter
or converter for your particular situation.
5
F:...MPH6929ENG.VP
Thu Jun 14 15:47:01 2001
Download from Www.Somanuals.com. All Manuals Search And Download.
Color profile: Disabled
Composite Default screen
Connecting the Telephone Cords
Consider these safety guidelines before connecting the telephone cords:
Caution!
Place the power cord so
that it does not create a
trip hazard or where it
could become chafed and
create an electrical hazard
or fire.
• Never install telephone wiring during a lightning storm.
• Never touch uninsulated telephone wires or terminals unless the
telephone line has been disconnected.
• Use caution when installing or modifying telephone lines.
Applying Power to the Base
This phone requires an AC outlet, without a switch to interrupt power,
and the included AC adapter. To relieve strain on the DC plug when the
phone is placed on a deskor table, wrap the power cord around the
strain relief notch on the bottom of the base.
ADAPTER SAFETY FEATURES
Before using your phone,
fully charge the Nickel-
Cadmium battery packfor
15-20 hours.
If the AC adapter furnished with this phone has a polarized line plug (a
plug having one blade wider than the other), this plug will fit into the
power outlet only one way. If you are unable to insert the plug fully into
the outlet, try reversing the plug.
Do not alter the shape of the blades of the polarized plug!
NOTE: If you cannot plug the
AC adapter into the outlet,
contact someone about
replacing the outlet.
AC
ADAPTER
Plug the AC Adapter into a
standard 120 V AC wall outlet.
Do not use an outlet controlled
Wide
Blade
by a wall switch. Use only the
AC Adapter supplied with
this phone.
6
F:...MPH6929ENG.VP
Thu Jun 14 15:47:03 2001
Download from Www.Somanuals.com. All Manuals Search And Download.
Color profile: Disabled
Composite Default screen
Installing and Adjusting our Phone
Y
DESK/TABLETOP INSTALLATION
Before choosing a location
for your phone, read the
“Installation Considerations”
included in the “Precautions
and Important Safety
Instructions” brochure.
1) Plug the AC adapter cord into the 9 V DC input jackon the backof
the base.
2) Wrap the AC adapter cord around the strain relief notch.
Place the power cord so that it does not create a trip
hazard or where it could become chafed and create a fire
or electrical hazard.
3) Plug the AC adapter into a standard 120 V AC wall outlet.
Use only the supplied AC adapter supplied with this phone
and DO NOT use an outlet controlled by a wall switch.
4) Charge the battery (refer to “Charging the Battery Pack,” page 12).
5) Plug one end of the telephone cord into the TEL LINE jackon the
backof the base.
6) Plug the other end of the cord into your telephone jackon the wall.
7
F:...MPH6929ENG.VP
Thu Jun 14 15:47:05 2001
Download from Www.Somanuals.com. All Manuals Search And Download.
Color profile: Disabled
Composite Default screen
7) Set the base on a deskor tabletop, and
place the handset into the base
as shown. Then, raise the antenna
to a vertical position.
Before using your phone,
fully charge the Nickel-
Cadmium battery packfor
15-20 hours.
WALL INSTALLATION
M Standard wall plate mounting
This phone can be mounted on any standard AT&T or GTE wall plate.
1) Slide the wall mount adapter into
the notches at the top of the base.
Place the power cord so
that it does not create a
trip hazard or where it
could become chafed and
create a fire or electrical
hazard.
2) Rotate the wall mount adapter
down and snap it into place at the
bottom of the base.
3) Plug the AC adapter into the base.
4) Put the AC adapter cord inside the
molded wiring channel, then
wrap it around the strain relief
notch. Plug the AC adapter into a
standard 120 V AC wall outlet.
8
F:...MPH6929ENG.VP
Thu Jun 14 15:47:10 2001
Download from Www.Somanuals.com. All Manuals Search And Download.
Color profile: Disabled
Composite Default screen
5) Plug one end of the telephone
cord into the TEL LINE jack
on the backof the base, then
plug the other end into a
standard telephone jack.
DO NOT use an outlet
6) Line up the mounting slots on
the base with the mounting
posts on the wall, then push
in and down until
controlled by a wall switch.
the phone is firmly seated.
7) On the base unit, pull the handset
retainer out of the slot and rotate
it clockwise 180 degrees.
Before you plug the other
end of the telephone cord
into the modular jackon
the wall, charge the battery
(refer to “Charging the
Battery Pack,” page 12).
8) Flip the retainer from front to back,
then slide it backinto the slot so
that the lip of the retainer faces up
and the oval is at the bottom of the
retainer. This will hold the handset
in place.
9
F:...MPH6929ENG.VP
Thu Jun 14 15:47:14 2001
Download from Www.Somanuals.com. All Manuals Search And Download.
Color profile: Disabled
Composite Default screen
M Direct wall mounting
If you don’t have a standard wall plate, you can mount your phone
directly to the wall. Before doing this, consider the following:
• Select a location away from electrical cables, pipes, or other items
behind the mounting location. Inserting screws into areas such as
this can be hazardous.
• Try to mount your phone within 10 - 15 feet of a working phone
jackin order to avoid excessive lengths. Remember, you are not
mounting your phone to a wall plate with a built-in phone jack.
• If the selected mounting area has no wooden support beams directly
behind it, you will need the appropriate anchoring devices in order
for the wall to properly support your phone.
1) Insert two mounting screws into
the wall, with their appropriate
anchoring device if necessary,
3-15/16 inches apart. Allow about
3/16 of an inch between the wall
and screw heads for mounting
the phone.
2) Slide the wall mount into the
notches at the top of the base.
3) Rotate the wall mount adapter
down and snap it into place at
the bottom of the base.
4) Plug the AC adapter into the base.
10
F:...MPH6929ENG.VP
Thu Jun 14 15:47:16 2001
Download from Www.Somanuals.com. All Manuals Search And Download.
Color profile: Disabled
Composite Default screen
5) Put the AC adapter cord inside the
molded wiring channel, then
wrap the AC adapter cord around
the strain relief notch. Plug the
AC adapter into a standard 120 V
AC wall outlet.
6) Plug one end of the telephone cord
into the TEL LINE jackon the back
of the base, then plug the other end
into a standard telephone jack.
7) Line up the mounting slots on the
base with the mounting screws on the
wall, then push in and down until the
phone is firmly seated.
8) On the base unit, pull the handset
retainer out of the slot and rotate
it clockwise 180 degrees.
11
F:...MPH6929ENG.VP
Thu Jun 14 15:47:22 2001
Download from Www.Somanuals.com. All Manuals Search And Download.
Color profile: Disabled
Composite Default screen
9) Flip the retainer from front to back,
then slide it backinto the slot so
that the lip of the retainer faces up
and the oval is at the bottom of the
retainer. This will hold the handset
in place.
INSTALLING THE HANDSET BATTERY PACK
1) Remove the handset battery cover
2
For initial charging, the battery
1
packwill already be inside the
compartment, but will not be
plugged in.
2) Plug the battery’s cable into
3
the handset
3) Replace the battery cover.
The plastic connectors will fit together only one
way. Make sure the battery’s connector is
properly aligned. Use only the supplied battery
pack (model BT-905).
CHARGING THE BATTERY PACK
M Initial battery charging
Before plugging the phone line into your new phone for the first time,
fully charge the rechargeable battery packfor 15-20 hours
without interruption.
1) Place the handset on the base.
2) Make sure that the status LED lights. If the LED doesn’t light, checkto
see that the AC adapter is plugged in and that the handset makes good
contact with the base charging contacts.
12
F:...MPH6929ENG.VP
Thu Jun 14 15:47:23 2001
Download from Www.Somanuals.com. All Manuals Search And Download.
Color profile: Disabled
Composite Default screen
M Low battery indicator
When the battery packis very low and
needs to be charged, the phone is pro-
grammed to eliminate functions in
order to save power. If the phone
is not in use, the talk/batt LED
flashes every three seconds.
If the phone is in use, the talk/batt
LED flashes every three seconds
and the handset beeps. Complete your
conversation as quickly as possible and
return the handset to the base for charging.
Use only the supplied
battery (BT-905) supplied
with your phone.
CLEANING THE BATTERY CONTACTS
To maintain a good charge, clean all charging contacts on the handset
and base about once a month with a pencil eraser or other contact
cleaner. DO NOT use liquids or solvents; you may damage your phone.
PAGE
To locate the handset (while it’s
off the base), press page on the
base. The handset beeps for 60
seconds.
Paging is cancelled.
When the handset is returned to
the base, paging is cancelled.
13
F:...MPH6929ENG.VP
Thu Jun 14 15:47:25 2001
Download from Www.Somanuals.com. All Manuals Search And Download.
Color profile: Disabled
Composite Default screen
SETTING THE PULSE/TONE SWITCH
Be sure the PULSE/TONE switch is in
the TONE position unless your local
phone system uses pulse dialing.
Most phone systems use
tone dialing. Checkwith
your local phone company
if you’re not sure whether
your system is tone or pulse.
ADJUSTING THE RINGER CONTROLS
M Handset ringer tone and ringer volume
When the phone is in standby mode, pressing the volume key on the
handset selects the handset ringer volume and tone. There are two
ringer tones each with two volume levels; high
and low.
M Handset earpiece volume
The handset earpiece volume settings (Normal, High and Loud) can only
be adjusted during a call. Press volume to select Normal, High, or Loud.
When you hang up, the phone keeps the last volume setting selected.
M Base unit ringer on-off
To turn the base ringer on, select the
RINGER ON position. To turn the
base ringer off, select the
RINGER OFF position.
14
F:...MPH6929ENG.VP
Thu Jun 14 15:47:28 2001
Download from Www.Somanuals.com. All Manuals Search And Download.
Color profile: Disabled
Composite Default screen
AUTOMATIC DIGITAL CODE SECURITY
To prevent other parties from making unauthorized calls on your
phone line, a digital code was added to the MPH6929. Your phone’s
handset and base share this code, which is randomly set each time you
place the handset in the charging cradle.
M To reestablish communication between the handset and the
base in the event of a power failure
1) Restore power to the base.
2) Place the handset on the base. The status LED blinks to indicate that
the digital security code is reset.
15
F:...MPH6929ENG.VP
Thu Jun 14 15:47:28 2001
Download from Www.Somanuals.com. All Manuals Search And Download.
Color profile: Disabled
Composite Default screen
Using Your New Phone
MAKING AND RECEIVING CALLS
Handset
On Base
Handset
Off Base
Pickup the handset, or
press speaker on the base. handset or press speaker
Press any button on the
To answer
a call
on the base.
1) Pickup the handset.
2) Press talk.
3) Listen for the dial
tone.
1) Press talk.
2) Listen for the dial
tone.
To make
a call
3) Dial the number.
4) Dial the number.
Press talk, or return the Press talk, or return the
handset to the base (Auto handset to the base (Auto
To hang up
Disconnect), or press
Disconnect), or press
speaker.
speaker on the base.
1) Pickup the handset.
1) Press talk.
2) Press talk.
To redial 3) Listen for the dial
tone.
2) Listen for the dial tone.
3) Press redial.
4) Press redial.
FLASH AND CALL WAITING
If you have “call waiting” service
and a call waiting tone sounds
while you are on a call, press
flash to accept the waiting call.
There is a short pause, then you
will hear the new caller. To
return to the original caller,
press flash again.
16
F:...MPH6929ENG.VP
Thu Jun 14 15:47:32 2001
Download from Www.Somanuals.com. All Manuals Search And Download.
Color profile: Disabled
Composite Default screen
STORING A PHONE NUMBER IN MEMORY
Your MPH6929 phone has 10 memory locations for storing important
telephone numbers.
1) Remove the handset from the base.
The pause button counts
as one digit. Pressing
2) Press mem.
The talk/batt LED blinks.
pause more than once
increases the length of
pause between numbers.
3) Enter the phone number, up
to 16 digits. If a pause is
needed during dialing to access
a long distance or other
service, press pause to
insert a pause.
4) Press mem again.
5) Enter the memory location
(0-9) on the keypad. A tone
indicates that the number
is stored.
You cannot store numbers in M1 M2 or M3.
,
Refer to “One-Touch Dialing.”
DIALING A STORED NUMBER
M Using the memory location features
1) Press talk.
2) Press mem.
3) Enter the memory location (0-9, or M1-M3) on the keypad. The stored
number automatically dials.
If you select a memory location that does not
have a stored number, the handset will beep
rapidly and the phone will not dial.
17
F:...MPH6929ENG.VP
Thu Jun 14 15:47:34 2001
Download from Www.Somanuals.com. All Manuals Search And Download.
Color profile: Disabled
Composite Default screen
M One-touch priority dialing
Your phone is equipped with three “One-Touch Priority” keys for
instant dialing. You cannot store phone numbers directly into M1
M2 or M3. They are only used to dial phone numbers stored into
memory locations 1, 2 and 3. (See “Storing a Phone Number in
Memory,” page 17.)
,
To instantly dial phone
numbers stored in memory
locations 1, 2 or 3, simply press
M1 M2 or M3. (There is no
,
need to press talk; the phone
will automatically dial.)
An error sounds and the
erase procedure will be
canceled if more than 20
seconds elapse between
each keystroke.
If you press M1, M2 or M3, and no phone number was stored in
memory locations 1, 2, or 3, the phone will beep rapidly but will not
dial.
CHAIN DIALING
On certain occasions after dialing a number, you may be requested to
enter an access code, such as your account number. You can enter this
number into a memory location for later use by doing the following.
1) Store the access code into one of the memory locations (0-9) or
memory keys M1, M2, or M3 following the steps above.
2) Dial the party or service main number.
3) When you need to enter the special number, press mem followed by
the memory location (0-9) or memory keys M1, M2, or M3.
ERASING A STORED NUMBER FROM MEMORY
1) Remove the handset from the base unit.
2) Press the MEM button twice.
3) Press the memory location (0-9). A tone indicates that the stored number
is erased from memory.
18
F:...MPH6929ENG.VP
Thu Jun 14 15:47:35 2001
Download from Www.Somanuals.com. All Manuals Search And Download.
Color profile: Disabled
Composite Default screen
REDIAL
The redial key redials the last number dialed. The redialed number
can be up to 32 digits long.
TONE
The tone feature only
applies when the base unit
is set to pulse.
If you are dialing in the pulse mode
and need to enter tone digits, press
tone to enter the digits. Once the call
has ended, the tone mode is canceled
and pulse dialing resumes.
TRAVELING OUT-OF-RANGE
During a call, as you begin to move your handset too far from your
base unit, noise increases. If you pass the range limits of the base unit,
your call will terminate within 20 seconds.
CHANNEL
To help eliminate background noise, press chan to change channels.
USING THE SPEAKERPHONE
To use the speakerphone to answer a call, press speaker on the base.
Direct your voice to the microphone on the bottom of the base. To
hang up, press speaker again.
Adjust the speakerphone
volume by pressing M for
louder or M for softer.
To use the speakerphone while making a call, first dial the number
using the handset. Then press speaker on the base unit. You can press
talk to disconnect the handset and continue the call with the
speakerphone. Press speaker to hang up.
THREE-WAY CALL
First, dial the number using the handset. Then, press speaker to set up
a three-way call between the base, handset, and the person on the line.
19
F:...MPH6929ENG.VP
Thu Jun 14 15:47:36 2001
Download from Www.Somanuals.com. All Manuals Search And Download.
Color profile: Disabled
Composite Default screen
Setting Up the Integrated Answering Device
THE INTEGRATED ANSWERING DEVICE
The MPH6929 has a built-in answering system that answers and records
incoming calls. You can also use your answering system to record a
conversation, leave a memo message for others who use the phone, or to
announce a special message to callers when you’re away from your phone.
FEATURES
• Digital Tapeless Recording
• 15 minutes of Recording Time
• Call Screening
• Selectable Outgoing Messages
• Time and Day Stamp
• Remote Message Retrieval and Room Monitor
• Toll Saver
• Conversation Recording
Digital Tapeless Recording allows you to quickly review, save, or delete
the messages you choose. You’ll never have to worry about a tape
wearing out, jamming, or resetting improperly.
The Integrated Answering System is easy and convenient to use, but
please read through all of the instructions carefully before attempting
to use it.
20
F:...MPH6929ENG.VP
Thu Jun 14 15:47:36 2001
Download from Www.Somanuals.com. All Manuals Search And Download.
Color profile: Disabled
Composite Default screen
TURNING THE ANSWERING SYSTEM ON/OFF
1) To turn the answering system on,
press answer on/off. A beep
tone will sound and the current
outgoing message will play on the
base speaker. A beep tone will
sound after the outgoing message
plays. The message counter LED
lights to indicate that the unit is
ready to answer calls.
Adjust the volume of the
system’s announcements
by pressing M for louder
or M for softer on the
base speaker.
2) To turn the answering system off, press answer on/off again. A beep
tone will sound followed by the announcement “Answer off” and the
message counter LED will go out.
SETTING THE CLOCK
The clockon the MPH6929 Answering System starts when power is
applied to the base. Follow these steps to set the clockto the
correct time:
Press skip or repeat
multiple times to scroll
through days, hours,
minutes, etc.
1) Press and hold clock until a beep
tone sounds.
If you make no entries
within two minutes, the
system returns to standby.
2) Next, press the skip or repeat
key until the correct day is
announced. (Numbers zero
through six display on the base as
each day is announced.)
3) Press clock again to select the day.
21
F:...MPH6929ENG.VP
Thu Jun 14 15:47:40 2001
Download from Www.Somanuals.com. All Manuals Search And Download.
Color profile: Disabled
Composite Default screen
4) Press skip or repeat until you hear the current hour setting. Numbers
1 through 12 display on the base as each hour is announced.
5) Press clock again to select the correct hour.
6) Press skip or repeat until you hear the current minute setting. The
numbers 0 through 59 display on the base as each minute
is announced.
7) Press clock again to select the correct minute. The AM/PM setting
is announced.
8) The LED displays an A or P. Press skip or repeat until you hear the
correct AM/PM setting.
9) Press clock again to end the time/day setting. The MPH6929
announces the time that you have set.
SETTING YOUR OUTGOING MESSAGE (GREETING)
When you receive a call, the answering system automatically plays
either a preset message or your own personal outgoing message.
You can record up to a 30-
second outgoing message.
M Preset message
The following message is prerecorded:
“Hello, no one is available to take your call. Please leave a message
after the tone.”
To record your own greeting, follow the steps below.
M Recording your personal outgoing message
1) Press and hold OGM until you
hear a long tone. Start recording
your message immediately after
you hear the long tone end. The
message counter LED will blink,
indicating record mode.
Stand within 12 inches in
front of the microphone
and speakclearly when
recording your outgoing
message.
22
F:...MPH6929ENG.VP
Thu Jun 14 15:47:42 2001
Download from Www.Somanuals.com. All Manuals Search And Download.
Color profile: Disabled
Composite Default screen
2) When you are finished recording your message, press OGM again.
A tone sounds and your message plays backon the base speaker.
To choose between the prerecorded outgoing
message and your personal outgoing message,
press OGM during outgoing message playback.
This switches between the two options.
M Announce only feature
The Announce Only feature plays a prerecorded outgoing message or
your own personal outgoing message, but it will not allow the caller to
leave a message.
Move the REC TIME switch
to the ANN position. The
message counter LED displays
A when the system is on standby.
SELECTING THE MESSAGE RECORD TIME
You can set your answering system to record messages up to one or
four minutes long.
One minute option: move the
REC TIME switch to 1.
Four minute option: move the REC TIME switch to 4.
23
F:...MPH6929ENG.VP
Thu Jun 14 15:47:45 2001
Download from Www.Somanuals.com. All Manuals Search And Download.
Color profile: Disabled
Composite Default screen
SELECTING A PIN CODE
To play your messages from a remote location, you will need to enter a
two-digit Personal Identification Number (PIN) code (00-99). To select
a PIN, perform the following steps:
1) On the base, press and hold the pin
button. A beep sounds, and the LED
displays 00.
If you make no entries
within two minutes, the
system returns to standby.
2) To set the first number, press
skip or repeat to scroll from 0
to 9. When the desired number
appears in the display, press pin.
This selects the first number.
Press skip or repeat
multiple times to scroll
through numbers on
the display.
3) To set the second number, press skip or repeat to scroll from 0 to 9.
When the desired number appears in the display, press pin. This
selects the second number and the entered PIN is announced.
24
F:...MPH6929ENG.VP
Thu Jun 14 15:47:48 2001
Download from Www.Somanuals.com. All Manuals Search And Download.
Color profile: Disabled
Composite Default screen
SETTING THE TOLL SAVER SWITCH
The ring time/toll saver switch allows you
to set the number of rings the
caller hears before your
answering system plays your
outgoing message. You can set
the switch to answer after two
rings or after four rings. In the
TS (Toll Saver) position, the
answering system picks up after
two rings if you have new messages, and after four rings if there are
none. This way, if you call long distance to checkyour messages, you
can hang up after the second ring to avoid billing charges.
USING THE RESET BUTTON
The RESET button is used to
initialize the base computer.
The RESET button can be used if an AC power line disturbance
causes the answering system to malfunction and become
inoperative. Pressing RESET does NOT erase any data stored in
your system memory.
25
F:...MPH6929ENG.VP
Thu Jun 14 15:47:50 2001
Download from Www.Somanuals.com. All Manuals Search And Download.
Color profile: Disabled
Composite Default screen
Using the Integrated Answering Device
PLAYING YOUR MESSAGES
The base LED shows the number of total messages on the display. If the
display is blinking, then there are new messages waiting for you. The
MPH6929 is designed to play your new messages first. After you play
your new messages, you can then play your old messages.
To stop playing your
messages at any time,
press play/stop again.
1) Press play/stop. The system
announces the number of new and
old messages. The time and day each
message was received is announced
after the message is played, and the
message counter LED displays the
number of the current message.
2) When all new messages have played, a long tone is heard. The message
counter LED stops flashing to indicate that all of the new messages have
been reviewed.
3) After you have reviewed your new messages, you can play your old
messages again. Press play/stop and follow the instructions above.
REPEATING A MESSAGE
1) Press play/stop to review your
messages. The number of stored
messages is announced.
26
F:...MPH6929ENG.VP
Thu Jun 14 15:47:53 2001
Download from Www.Somanuals.com. All Manuals Search And Download.
Color profile: Disabled
Composite Default screen
2) After a message has played for a few
seconds, press repeat to replay
the message.
Pressing repeat before
two half seconds of the
message has played causes
the system to scan back
one message.
3) Press play/stop at any time to stop reviewing your messages and
return to standby. The message counter LED shows the total number of
message-s still on the system.
SKIPPING A MESSAGE
If you have several
messages, press repeat
until you return to the
message you want to
replay.
1) Press play/stop to review your
messages. The number of messages
is announced.
Each time skip is
2) Press skip at anytime to skip to the
pressed, the system scans
forward one message. If
you have several messages,
press skip to find the
message you want to play.
next message.
3) Press play/stop at any time to stop reviewing your messages and
return to standby. The message counter LED shows the total number of
messages still on the system.
27
F:...MPH6929ENG.VP
Thu Jun 14 15:47:58 2001
Download from Www.Somanuals.com. All Manuals Search And Download.
Color profile: Disabled
Composite Default screen
DELETING A MESSAGE
1. Press play/stop to review
your messages.
When you press delete,
you are permanently
deleting the message.
Once deleted, the message
cannot be replayed.
2. If you decide to delete a message,
press delete anytime during the
message. The system beeps and
immediately goes to the next
message.
3. After you have played all of your messages, a long tone sounds on the
base speaker.
The system automatically
returns to standby when
all messages have played.
To delete all messages, press and hold delete after reviewing
your messages. A tone sounds when all message are cleared.
MEMO
The Memo function allows the user to record a message on the base.
1) Press and hold memo. A beep tone
sounds and the message counter
LED begins to blink.
The voice memo function
is completely independent
of the outgoing message.
It’s handy for leaving
others a quickmessage.
28
F:...MPH6929ENG.VP
Thu Jun 14 15:48:03 2001
Download from Www.Somanuals.com. All Manuals Search And Download.
Color profile: Disabled
Composite Default screen
2) Release memo and speakinto the microphone.
3) When you have finished, press memo or play/stop to stop
recording. The system returns to standby.
A voice memo message is
treated as a typical
recorded message and will
be added to the stored
messages.
RECORDING A CONVERSATION
You can record up to a 10 minute conversation while you are using
your phone.
1) During a conversation from the
handset, press and hold memo.
The unit begins recording and two
dashes show in the display. A beep
that can be heard by both parties
sounds every 15 seconds.
A recorded conversation is
treated as a typical
message and will be added
to the stored messages.
2) To stop recording, press memo or play/stop again.
REMOTE ACCESS AWAY FROM HOME
You can operate your answering system from a remote location using
any touch-tone telephone. Use this function to checkfor recorded
messages, to play or delete messages, even to record a new
outgoing message, and to monitor sounds in the room.
For Remote Answering
System On, wait ten rings
until the machine answers.
1) Call your telephone number.
2) During the outgoing message playback, press # followed by your PIN
code. Refer to page 24 for instructions on how to select a PIN code.
3) The answering system announces the time and day stamp followed by
the number of messages stored in memory. Message playback
automatically begins.
29
F:...MPH6929ENG.VP
Thu Jun 14 15:48:05 2001
Download from Www.Somanuals.com. All Manuals Search And Download.
Color profile: Disabled
Composite Default screen
4) You may continue to listen to your messages, or you may select a
command from the following chart:
FUNCTION
PRESS
Repeat a Message
#
#
#
#
#
#
#
#
#
#
then
then
then
then
then
then
then
then
then
then
1
2
3
4
5
6
7
8
9
You must enter a command
within 15 seconds of
Playing your Messages
Skipping a Message
Deleting a Message
Stop Message Playback
Answering System On
Memo Record/Stop
OGM Record/Stop
entering command waiting
mode or the answering
system automatically hangs
up and returns to standby.
Answer System Off
Remote Room Monitor
The system will only play
backmessages for four
5) After all of your messages have played, you will hear intermittent beeps
indicating that the system is in the command waiting mode. You may
enter another command at this time from the chart above.
minutes and then it returns
to command waiting mode.
To continue playing your
messages, press
#
then
2
6) When you are finished, hang up to exit the system. The answering
system automatically returns to standby.
again within 15 seconds.
30
F:...MPH6929ENG.VP
Thu Jun 14 15:48:05 2001
Download from Www.Somanuals.com. All Manuals Search And Download.
Color profile: Disabled
Composite Default screen
REMOTE ROOM MONITOR
You can call your answering system from any touch-tone phone and
monitor sounds in the room where your base is installed.
1) Call your telephone number.
2) During the outgoing message playback, press
#
followed by your
PIN code.
3) The answering system begins announcing the time and day stamp.
4) Press then while the system announces the time and day stamp.
#
You hear sounds in the room where your phone is installed. After 15
seconds, the answering system returns to the command waiting mode.
You cannot use
while the new messages are
playing. Press then 5 to
stop Message playbackfirst
and go to step 4.
#
and
#
5) Press
#
then to monitor the room for another 15 seconds. Or, select
another remote function. Or, hang up to exit the system. The
answering system automatically returns to standby.
31
F:...MPH6929ENG.VP
Thu Jun 14 15:48:06 2001
Download from Www.Somanuals.com. All Manuals Search And Download.
Color profile: Disabled
Composite Default screen
QUICK REFERENCE CHART
If your phone is not performing to your expectations, please try these
simple steps first.
PROBLEM
SUGGESTION
The charge light won’t come
on when the handset is
placed in the base.
• Make sure the AC adapter is
plugged into the base and wall
outlet.
• Make sure the handset is properly
seated in base.
• Make sure the charging contacts on
the handset and base are clean.
The audio sounds weak
and/or scratchy.
• Make sure that the base antenna is
in a vertical position.
• Move the handset and/or base to a
different location away from metal
objects or appliances and try again.
• Press chan to help eliminate
background noise.
• Make sure that you are not too far
from the base.
Can’t make or receive calls.
• Checkboth ends of the base
telephone line cord.
• Make sure the AC adapter is
plugged into the base and
wall outlet.
• Disconnect the AC adapter for a few
minutes, then reconnect it.
• Place the handset backon the
charging cradle for a few seconds.
The status LED will blink
indicating that the phone has
been reset.
• Make sure that you are not too far
from the base.
32
F:...MPH6929ENG.VP
Thu Jun 14 15:48:06 2001
Download from Www.Somanuals.com. All Manuals Search And Download.
Color profile: Disabled
Composite Default screen
PROBLEM
SUGGESTION
The handset doesn’t ring or
receive a page.
• The Nickel-Cadmium battery pack
may be weak. Charge the battery
on the base unit for 15-20 hours.
• The handset may be too far away
from the base unit.
• Place the base unit away from
appliances or metal objects.
• Place the handset backon the
charging cradle for a few seconds.
The status LED will blink
indicating that the phone has
been reset.
The answering system does
not work.
• Make sure the base unit is plugged in.
• Make sure the answering system is
turned on.
• Press RESET after an AC line spike.
The answering system does
not answer calls.
• Set the REC TIME switch to either
the one minute or four
minute option.
• The memory may be full. Delete
some or all of the saved messages.
Messages are incomplete.
• The incoming messages may be too
long. Remind callers to leave a
brief message.
• The memory may be full. Delete
some or all of the saved messages.
After a power failure, the
outgoing message is deleted.
• Record your personal outgoing
message again. The default
messages should remain.
No sound on the base unit
speaker during call
monitoring or
• Adjust the speaker volume on the
base unit.
message playback.
33
F:...MPH6929ENG.VP
Thu Jun 14 15:48:06 2001
Download from Www.Somanuals.com. All Manuals Search And Download.
Color profile: Disabled
Composite Default screen
PROBLEM
SUGGESTION
Cannot access remote call-in
features from another touch-
tone phone.
• Make sure you’re using the correct
PIN number.
• Make sure that the touch-tone
phone you’re using can transmit
the tone for at least two seconds. If
it cannot, you may have to use
another phone to access
your messages.
34
F:...MPH6929ENG.VP
Thu Jun 14 15:48:06 2001
Download from Www.Somanuals.com. All Manuals Search And Download.
Color profile: Disabled
Composite Default screen
Specifications
GENER AL
The MPH6929 complies with FCC Parts 15 and 68.
Frequency control: PLL
Modulation: Frequency Shift Keying
Operating temperature: 0º to 50º C (+32º F to +122º F)
BASE
Transmit Frequency: 925.997 to 927.947 MHz
Receive Frequency: 902.102 to 904.102 (40 channels)
Power requirements: 9V 350 mA (from AC adapter)
Size: 7-3/8 in.(W) x 2 in. (D) x 8-3/4 in. (H)
Weight: Approx. 21.1 oz. (including optional battery)
HANDSET
Transmit Frequency: 902.102 to 904.102 MHz
Receive Frequency: 925.997 to 927.947 (40 channels)
Power requirements: Rechargeable Nickel-Cadmium battery pack
Size (without antenna): 2.28 in. (W) x 1.73 in. (D) x 7.09 in. (H)
Weight: Approx. 8.9 oz. (including battery)
Battery: BT-905
Capacity
Talkmode
600 mAH, 3.6V
7 hours
Standby mode
14 days
Specifications, features, and availability of optional accessories are
all subject to change without prior notice.
35
F:...MPH6929ENG.VP
Thu Jun 14 15:48:06 2001
Download from Www.Somanuals.com. All Manuals Search And Download.
Color profile: Disabled
Composite Default screen
MEMOREX LIMITED WARRANTY TELEPHONES
We at MEMOREX believe you will be pleased with your new Product. Please read this Warranty carefully.
Memorex warrants this product to be free from manufacturing defects including original parts and workmanship
for a period of one (1) year from the date of original purchase in, and if used in, the United States.
Should you find your unit is not operation properly during the terms of full coverage of this warranty, one
(1) year, you should contract your original purchase for an exchange with a valid receipt. If necessary,
Memorex will provide one of the following options (at Memorex's discretion), providing the manufacturing
defect is verified along with the date of purchase.
•Repair service for one (1) year from date of original purchase at no charge for labor and parts at their authorized
warranty service facility, providing the manufacturing defect is verified along with the date of purchase.
•Replacement of defective unit with either a new, refurbished, or equivalent model at no charge for
one (1) year from date of original purchase.
This warranty is void if the product is:
A) Damaged through negligence, abuse, misuse, accident, or acts of God.
B) Used in commercial application or rentals.
C) Modified or repaired by anyone other than Memorex or their expressly authorized representative.
D) Damage resulting from the improper connection to equipment of other manufactures.
This warranty does not cover:
A) Cost incurred in the shipping of the product to and from the Memorex authorized repair facility listed.
B) Damage or improper operation caused by the failure to follow the operating instructions provided with the product.
C) Routine adjustments to the product, which can be performed by the customer as outlined in the owner's manual.
D) Signal reception problems caused by external factors.
E) Products not purchased in the United States
F) Damage to the products used outside the United States.
G) Damage to audiocassette tapes.
H) Damage to Compact Discs.
In the event that service is required under this warranty, please contact CUSTOMER SERVICE at 1-800-919-
THIS WARRATY IS NON-TRANSFERABLE AND APPLIES SOLELY TO THE ORIGINAL PURCHASER
AND DOES NOT EXTEND TO SUBSEQUENT OWNERS OF THE PRODUCT. ANY APPLICABLE
IMPLIED WARRANTIES, INCULDING THE WARRANTY OF MERCHANTABILBITY, ARE LIMITED IN
DURATION TO A PERIOD OF THE EXPRESSED WARRANTY AS PROVIDED HEREIN BEGINNING
WITH THE DATE OF THE ORIGINAL PURCHASE AT RETAIL AND NO WARRANTIES, WHETHER
EXPRESSED OR IMPLIED SHALL APLLY TO THE PRODUCT THEREAFTER. MEMOREX MAKES NO
WARRANTY AS TO THE FINESS OF THE PRODUCT FOR ANY PARTICULAR PURPOSE OR USE.
THE EXTENT OF MEMOREX'S LIABILITY UNDER THIS LIMITED WARRANTY IS THE REPAIR OR
REPLACEMENT PROVIDED ABOVE AT THE SOLE DISCRETION OF MEMOREX. IN NO EVENT
SHALL MEMOREX'S LIABILITY EXCEED THE PURCHASE PRICE PAID BY THE PURCHASER.
UNDER NO CIRCUMSTANCES SHALL MEMCORP BE LIABLE FOR ANY LOSS, DIRECT, INDIRECT,
INCIDENTAL, FORESEEN, UNFORESEEN, SPECIAL, OR CONSEQUENTIAL DAMAGE ARISING OUT
OF OR IN CONNECTION WITH THE USE OF THIS PRODUCT.
THIS WARRANTY IS VALID ONLY IN THE UNITED STATES. THIS WARRANTY GIVES YOU
SPECIFIC LEGAL RIGHTS, HOWEVER, YOU MAY HAVE OTHER RIGHTS WHICH MAY VARY FROM
STATE TO STATE. SOME STATES DO NOT ALLOW LIMITATION ON IMPLIED WARRANTIES OR
EXCLUSION OF CONSEQUENTIAL DAMAGE, THEREFORE THESE RESTRICTIONS MAY NOT APPLY
TO YOU.
©1999, Memorex is a registered trademarkof Memorex Telex N.V.
36
F:...MPH6929ENG.VP
Thu Jun 14 15:48:07 2001
Download from Www.Somanuals.com. All Manuals Search And Download.
1
1
1
1
1
1
1
0
.
F
M
l
o
a
s
h
2
2
2
2
2
2
2
2
3
3
3
3
3
2
.
.
.
.
.
.
.
.
.
D
S
e
l
p
e
3
3
3
3
3
4
4
t
e
5
.
P
l
a
y
/
e
S
t
o
p
1
2
.
.
R
B
e
s
e
t
1
.
.
.
.
.
.
e
m
o
r
y
3
R
A
e
e
a
6
t
.
V
o
i
i
c
p
M
e
m
o
a
s
e
R
i
n
g
e
r
2
N
u
m
e
r
i
c
4
5
K
e
y
p
n
a
s
d
w
e
7
8
9
0
1
r
.
.
.
.
.
O
S
O
n
k
/
O
f
f
O
f
f
-
O
n
3
4
T
n
e
M
S
i
c
r
o
p
I
h
o
n
u
e
t
g
o
i
n
g
m
e
n
s
a
3
4
5
6
7
8
9
.
P
u
l
s
e
/
T
o
n
e
R
e
d
i
a
l
6
e
t
P
N
B
a
e
s
c
e
A
n
t
e
i
n
.
D
T
C
I
n
9
V
J
a
c
k
5
6
P
H
a
u
s
e
7
8
e
t
C
l
o
c
R
k
o
r
d
T
m
e
.
e
l
L
i
n
e
J
a
c
k
a
n
d
s
e
t
R
i
n
P
B
S
S
g
a
a
p
p
p
e
g
s
r
e
R
i
n
g
T
i
m
e
.
H
a
n
d
s
e
t
A
n
t
e
n
n
a
a
V
n
o
d
l
u
T
m
o
n
e
e
9
0
s
e
l
e
c
e
t
S
p
e
a
k
e
r
.
.
.
H
a
n
d
s
e
1
1
1
2
2
t
E
a
r
p
i
e
c
e
7
.
C
h
n
a
e
n
-
n
e
l
e
e
a
a
a
k
e
r
B
u
t
t
o
n
T
T
a
a
l
l
k
k
/
B
a
t
t
L
o
w
L
E
D
1
2
3
4
5
8
9
0
1
.
.
.
.
O
H
T
o
u
c
1
2
h
.
P
r
i
o
r
k
i
e
y
r
K
L
e
E
y
D
l
s
a
n
d
s
e
t
M
.
i
e
c
S
r
o
e
p
h
k
o
e
n
r
e
V
o
u
m
e
H
a
n
d
s
e
t
3
R
.
t
S
a
t
i
a
n
t
e
u
r
s
C
L
l
E
i
D
p
C
h
a
r
g
i
n
g
4
.
C
o
M
n
e
t
s
a
s
c
a
t
g
s
e
C
o
u
n
t
e
r
6
7
29
30
20
39
8
9
31
10
11
32
33
34
35
36
37
38
40
41
12
13
14
15
16
17
18
19
23 24 25
27
28
22
26
21
Download from Www.Somanuals.com. All Manuals Search And Download.
|