MV-Flash M3+ User Guide
V2.1
This brief guide explains how to use and set up your MV-FLASH M3+ decoder board. It is
intended for Digital View/RemoteMedia staff who assemble ViewStream product for demos or for
customers, and for resellers of RemoteMedia equipment.
1 Introduction
The MV-FLASH M3+ is an MPEG decoder board designed to use with TV and Video
Monitors for playing MPEG-1/MPEG-2/MPEG-4 video and audio files.
•
•
•
•
•
•
•
•
•
MPEG-1, MPEG-2, MPEG-4* video
MPEG still picture output
JPEG picture
MP3 audio file
Video signals of PAL & NTSC standard
Composite and S-Video signal output
VGA output
Stereo audio output
RS-232 port (option)
* DivX MPEG-4 format
HOW TO PROCEED
Ensure you have all parts & that they are correct. Refer to:
•
•
•
General notes
System setup
Operating Instructions
IMPORTANT USAGE NOTE
This equipment is for use by developers and integrators; the manufacturer accepts no
liability for damage or injury caused by the use of this product. It is the responsibility of the
developer, integrators or other users of this product to:
•
•
•
Ensure that all necessary and appropriate safety measures are taken.
Obtain suitable regulatory approvals as may be required.
Check power settings to all component parts before connection.
DISCLAIMER
There is no implied or expressed warranty regarding this material.
- 1 -
Download from Www.Somanuals.com. All Manuals Search And Download.
A) Mechanical buttons
•
•
Standard MV-switchmount with 8 buttons.
Custom made switchmount for 1-8 buttons when connected to the buttons connector
CN6 via the standard switchmount cable.
•
Custom made switchmount kit for 1-8 buttons when connected to the Remote Ext.
socket (CN5) for alternative remote control buttons.
B) Touch screen segments
•
The MV-Flash M3+ when connected with a LCD interface controller can output videos
on to LCD screen. Button control can be performed via touch screen for panel sizes of
6.4”, 7.9”, 10.4”, and 15”
•
There are one types of button pattern layouts on the touch screen available: 8 buttons
for the 6.4”, 7.9”, 10.4” and 15” panels. (For any special button layout, please contact
local sales office.)
Fig.1 8-buttons for LCD screen sizes 6.4”, 7.9”, 10.4”, 15”
C) Button function settings
•
Whether the buttons are of the mechanical type (on the standard switchmount or
custom made) or the touch screen segment type, each button function can be
programmed with the DV Studio Advanced software program to perform a VCD
player mode function or specific track select function. (See DV Studio Advanced
user manual).
•
The DV Studio Advanced software program is separately provided
- 3 -
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Quick Start
CAUTION: Never connect or disconnect parts of the system when the system is powered up
as this may cause serious damage.
CONNECTION – Connection and usage are straightforward. However, care needs to be
taken with the following:
•
•
•
•
•
Ensuring parts have been correctly connected – both power & signal considerations.
Checking that all switches and jumpers are set correctly.
The input signal is compatible.
Legal & safety requirements have been met.
If you are using supplied cables & accessories, ensure they are correct for the model
of video monitor.
•
If you are making your own cables & connectors refer carefully to the video monitor
specifications and the “Connectors, Pin outs & Jumpers” section in this user guide to
ensure the correct pin-to-pin wiring.
Basic connection for MV-FLASH M3+ :
•
•
•
•
Connect the keys pad to CN5 (if required)
Set correct switch (S1) settings. (e.g. PAL/NTSC switch)
Connect the video and audio ext. cables from the MV-FLASH M3+ to the AV monitor.
Connect the power supply (DC 12V @ 1.2A minimum. - ensure correct + & -
orientation) to the controller power input (PP1).
•
Connect the on/off switch cable (p/n:4266804-01) or short Pin1-2 at S3 for “Auto
power on”
LED1
CN5
Touch screen/Keypad
1
1
LED2
1
CN6
CN11
1
CN10
BT1
S3
1
1
JA1
J6
3
Barcode reader
1
CN1
RS-232 add on
board
MV-FLASHM3+
1
1VR1
CNV1
J1
CN9
1
CN4
1
CN7
PP1
1
1
J2
J3
J4
Remote Control
Speaker
VGA Monitor
Monitor
Power supply
- 4 -
Download from Www.Somanuals.com. All Manuals Search And Download.
4 General Notes
The MV-FLASH M3+ is designed for use with Video Monitors and other analogue signal
input displays. Here are some notes for correct use:
•
•
Preparation - Before you proceed, please familiarize yourself with the various
connectors, jacks, switches and function buttons of the MV-FLASH M3+ unit (see the
‘System Design’ diagram).
The unit - Handle the unit with care; any knocking may cause components to come
loose and disconnect. Operate in a cool and dry place.
•
•
Power Input: 12V DC, 1.2A (minimum) is required; this should be a regulated supply.
Digital Video - use MPEG-1/2* video encoded at Video-CD standard. (See “Content
Creation Guide” for proper encoding rate.)
* For MPEG-2 video, the encoding rate is limited to 5Mb/s (in normal CF card)
•
•
Audio & Video output - Video - displays PAL & NTSC signals with either Composite,
S-video or Component signal. The PAL/NTSC switch should be set correctly. Audio -
Stereo output. Volume is controlled by the switch mount buttons.
Remote Ext. - Using the standard switch mount (p/n: 4161013-00) - 8 momentary
buttons for OSD config and video playback control (standard functions (in simple play
mode) being : Play, Stop, Pause, Next Track, Volume decrease, Volume increase,
Mute). An optional function control device is a custom-made switch mount connected
to the switches and buttons connector (CN6) with a maximum of 8 momentary buttons
•
Remote Ext. cable - The cables (p/n: 4266318-00) to the switches and buttons
connector should be of suitable quality and length so that impedance does not affect
performance. Generally lengths up to 1 meter (3 feet) should be acceptable.
•
•
•
•
•
LED (LED1) - The power LED indicator shows power is being supplied to the MV-
FLASH M3+. The Status LED indicates the status of CF card.
RS-232 serial port (option)– A add-on board (p/n:4160113-10) and RS-232 cable
(p/n: 4268912-00) are required. The serial port only supports barcode scanner.
USB – USB Client. Connect to PC or Notebook for content update without removing
the CF card.
VGA out – A extend cable (p/n: 4268910-00) is required. The VGA resolution is
support 640x480.
Service & Warranty: Warranty is invalidated if the unit is dismantled in any way. The
unit is not user serviceable or repairable.
CAUTION: do not attempt to remove any part of the casing or internal parts.
- 5 -
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Connectors, pinouts & jumpers
1
LED1
CN5
CNV3
1
1
J5
JP2
1
CN6
BT1
CN10
CN11
J6
JA1
S3
3
1
1
1
JP1
1
1
LED2
1
CN1
MV-Flash M3+
CN2
1
VR1
1
1
CNV1
CNV2
1
CN9
1
CN4
CN7
PP1
1
1
J1
J2
J3
J4
1
The various connectors are:
Ref
Purpose
Description
CN1
CN2
CN4
CN5
CN6
CN7
CN9
CN10
CN11
CNV1
Speaker out (L/R) connector
Reserved
Alternative Video/VGA switch
Remote Ext.
Switches and buttons connector
Alternative PAL/NTSC connector
Alternative audio output
Alternative power connector
I/O Expansion connector
JST B4B-XH-A
5x2 header (0.1” pitch)
JST B3B-PH-K
MINI DIN 8-way
Hirose 1.25mm, 9-pin, D3-3-1.25DSA
JST B2B-XH-A
JST B4B-PH-K
JS-1116-04WS
13x2 header socket (0.1” pitch)
JST B5B-PH-K
Alternative S-Video/ Composite video
output
CNV2
CNV3
LED1
LED2
J1
VGA output
Reserved
Power/Status LED
Alternative power LED connector
S-Video out
JST B6B-PH-K
JST B2B-PH-K
Stacked housing LED
1x2 header (0.1” pitch)
Mini DIN 4-way
J2
J3
Composite video out
Audio Left out
RCA jack (yellow)
RCA jack (red)
J4
J5
Audio Right out
USB
RCA jack (white)
Mini USB, 5-way
J6
PP1
CF Card connector
Main power input
CF-CARD, 25x2PIN 3M CF-II SOCKET
DC power jack, 2.5mm contact pin diameter
(Center +)
S1
S2
S3
JA1
IR1
VR1
BT1
PAL/NTSC switch
VIDEO/VGA switch
Power On/Off switch connector
5V Logic Power
IR Connector
6mm stem select switch
6mm stem select switch
JST B2B-XH-A
2x2 header (2mm pitch)
JST B3B-XH-A
Ext. Variable Resistor connector
Battery for Real time clock
3x2 header (0.1” pitch)
CR1216 Type
- 6 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Details:
CN1 – Speaker out (L/R)
PIN
1
2
3
4
SYMBOL
GND
L
GND
R
DESCRIPTION
Ground
Left speaker out
Ground
Right speaker out
CN2 – Reserved
CN4 – Alternative Video/VGA switch
PIN
1
SYMBOL
+5V
DESCRIPTION
Reserved
2
3
MODE
GND
VGA (short 2-3) Video (Open 2-3)
GND
CN5 - Remote Ext.
PIN
1
2
3
4
5
6
7
8
SYMBOL
SW1
SW2
SW3
SW4
SW5
SW6
SW7
SW8
DESCRIPTION
Button 1
Button 2
Button 3
Button 4
Button 5
Button 6
Button 7
Button 8
CN6 – Switches and buttons connector
PIN
1
2
3
4
5
6
7
8
SYMBOL
SW1
SW2
SW3
SW4
SW5
SW6
SW7
SW8
GND
DESCRIPTION
Button 1
Button 2
Button 3
Button 4
Button 5
Button 6
Button 7
Button 8
Ground
9
CN7 – Alternative PAL/NTSC connector
PIN
1
SYMBOL
SYSTEM
DESCRIPTION
PAL/NTSC select
1-2 short: NTSC
1-2 open: PAL
Ground
2
GND
- 7 -
Download from Www.Somanuals.com. All Manuals Search And Download.
CN9 - Alternative audio output
PIN
1
SYMBOL
GND
DESCRIPTION
Ground
2
3
AUDIO_L
GND
Audio left channel output
Ground
4
AUDIO_R
Audio right channel output
CN10 - Alternative power
PIN
1
SYMBOL
VCC
DESCRIPTION
+5V out
2
GND
Ground
3
GND
Ground
4
+12V
+12V out
CN11 – I/O Expansion
PIN
1
2
3
4
5
6
7
8
SYMBOL
LD08
LD09
LD10
LD11
LD12
LD13
LD14
LD15
/LCS
DESCRIPTION
Port Data 8
Port Data 9
Port Data 10
Port Data 11
Port Data 12
Port Data 13
Port Data 14
Port Data 15
CHIP SELECT
OUTPUT ENABLE
Port High Byte Write Enable
Port Address 20
Port Address 21
Auxiliary Port 6
Auxiliary Port 7
Aux3 Data I/O
General Input 0
General Input 1
General Input 2
General Input 3
General Input 4
General Input 5
Ground
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
/LOE
/LWRHL
/LA20
/LA21
AUX6
AUX7
EAUX32
GPI0
GPI1
GPI2
GPI3
GPI4
GPI5
GND
VCC
VCC3
GND
+5V
+3.3V
Ground
CNV1 - Alternative S-Video/Composite video output
PIN
1
2
SYMBOL
CHROMA
LUMA
DESCRIPTION
S-Video : Chroma out
S-Video : Luma out
Ground
3
GND
4
GND
Ground
5
CVBS
Composite video out
- 8 -
Download from Www.Somanuals.com. All Manuals Search And Download.
CNV2 - VGA output
PIN
1
SYMBOL
GND
DESCRIPTION
Ground
2
3
4
5
H_SYNC
V_SYNC
B
G
R
Horizontal Sync Output
Vertical Sync Output
Analog Blue
Analog Green
Analog Red
6
CNV3 - Reserved
LED2 – Alternative power LED connector
PIN
1
2
SYMBOL
LED2
GND
DESCRIPTION
Connect to Anode of LED
Connect to Cathode of LED
J1 - S-Video Out
PIN
1
SYMBOL
GND
DESCRIPTION
Ground
2
GND
Ground
3
4
LUMA_OUT
CHROMA_OUT
Luma Out
Chroma Out
J2 - Composite video Out
PIN
1
2
SYMBOL
CENTER
GND
DESCRIPTION
Center pin, composite out, 0.7Vp-p
Ground
J3 - Audio left out
PIN
1
2
SYMBOL
LEFT_AUDIO
GND
DESCRIPTION
Center pin, Audio Left output
Ground
J4 - Audio right out
PIN
1
2
SYMBOL
RIGHT_AUDIO
GND
DESCRIPTION
Center pin, Audio Right output
Ground
J5 - USB
PIN
1
2
3
4
SYMBOL
UVCC
D-
D+
GND
DESCRIPTION
USB - VCC
-VE USB Data
+VE USB Data
Ground
- 9 -
Download from Www.Somanuals.com. All Manuals Search And Download.
J6 – Compact Flash card connector
PIN
1
2
SYMBOL
GND
D3
DESCRIPTION
Ground
Data bit 3
3
D4
Data bit 4
4
D5
Data bit 5
5
D6
Data bit 6
6
D7
Data bit 7
7
8
9
/CE1
GND
GND
GND
GND
GND
VCC
GND
GND
GND
GND
A2
A1
A0
D0
D1
D2
NC
/CD1
/CD2
NC
Card enable 1
Ground
Ground
Ground
Ground
Ground
+5V
Ground
Ground
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Ground
Ground
Address bit 2
Address bit 1
Address bit 0
Data bit B3
Data bit B4
Data bit B5
No connection
Card detect pin 1
Card detect pin 2
No connection
No connection
No connection
No connection
No connection
Card enable 2
No connection
Memory read strobe
Memory write strobe
No connection
Interrupt request
+5V
NC
NC
NC
NC
/CE2
NC
/RD
/WR
NC
IRQ
VCC
GND
NC
RESET
NC
NC
NC
Pin45
Pin46
NC
Ground
No connection
System reset
No connection
No connection
No connection
BVD2
BVD1
No connection
No connection
No connection
Ground
NC
NC
GND
PP1 - Main power input
PIN
1
2
SYMBOL
+12_CENTER
GND
DESCRIPTION
+12V DC in center pin
Ground
- 10 -
Download from Www.Somanuals.com. All Manuals Search And Download.
S1 - PAL/NTSC switch
PIN
1-2
2-3
SYMBOL
PAL
NTSC
DESCRIPTION
PAL
NTSC
S2 - Video/VGA switch
PIN
1-2
2-3
SYMBOL
COMP_SVIDEO
VGA
DESCRIPTION
Composite / S-Video Output
VGA Output
S3 – Power On/Off switch connect
PIN
1
SYMBOL
12V_IN
DESCRIPTION
+12V input
2
12V_OUT
+12V output
IR1 – Infra-red
PIN
1
2
SYMBOL
GND
VCC
DESCRIPTION
Ground
+5V
3
IR
IR Data
Jumper JA1: 1-2, 3-4 closed (Factory default)
Jumper JP1: 1-2 closed (Factory default)
Jumper JP2: Reserved
Jumper VR1: 1-3, 2-4 closed (Factory default)
- 11 -
Download from Www.Somanuals.com. All Manuals Search And Download.
6 System Setup
A) SELECT SWITCHES
Before powering on the MV-FLASH M3+:
•
•
Make sure the corresponding signal cables have been connected from the Composite
or S-Video output jacks.
Set the 'PAL/NTSC' switch (S1) to the chosen output format.
B) POWER UP
Config mode
In config mode, you may need either external buttons or 8-segmented touch screen to
operate.
•
Holding button 8 and power on. The OSD menu screen will be shown as follow:
VOLUME
Y M
14
VER 5.00
D
H
M
S
2004 .10 .12
15 : 48 : 44
ID NO: 0712
DATA LOGGING: ON
OSD: ON
SAVE AND EXIT
•
•
Press button 8 to select or press button 7/6 for up/dn.
Press button 7or 6 for save and exit.
Auto-Play start up mode*
•
•
Plug in the external power supply
Insert CompactFlash Card containing DV Studio Advanced exported “.pll / .prj” and
other digital files. (e.g. .mpg, .mp3, .jpg) All filename should be in 8+3 format (i.e.
xxxxxxxx.xxx) and avoid using any illegal characters like “~”, “_”, “-“, etc
Switch the power 'on/off' switch to 'on'.
•
•
The first track of the collection of MPEG files will be auto-played.
Sleep mode*
•
•
Plug in the external power supply
Insert CompactFlash Card containing DV Studio Advanced exported “.pll / .prj” and
other digital files. (e.g. .mpg, .mp3, .jpg) All filename should be in 8+3 format (i.e.
xxxxxxxx.xxx) and avoid using any illegal characters like “~”, “_”, “-“, etc
Switch the power 'on/off' switch to 'on'.
•
- 12 -
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
Press the 'play' button'.
The first track of the collection of MPEG files will be played.
Note: special specific track playback activated by assigned button can also be performed in
sleep mode - contact local sales office.
*The Autoplay and Sleep playback mode are selected when writing the MPEG files on to the
CompactFlash Card by using DV Studio Advanced software.
C) AUTO-LOOP PLAYBACK
After Track 1 is set to play, it will play to the end, then Track 2 will start playing from
beginning to end, then Track 3 etc. When the MV-FLASH M3+ plays to the end of the last
track, it will automatically jump back to the beginning of Track 1, repeating tracks 1,2 then 3
etc. The MV-FLASH M3+ will play in auto-loop play mode, so long as none of the function
buttons are pressed. (NOTE: Loop playback is the standard playback setting of the MV-
FLASH M3+ but the track playback sequence can be changed as required: contact local
sales office.)
- 13 -
Download from Www.Somanuals.com. All Manuals Search And Download.
7 Operating Instructions
OPERATING MODES
There are two operating modes in MV-Flash M3+ – “playlist mode” and “simple play mode”
.
1. Playlist mode
When operating in playlist mode, both project file (*.prj) and playlist file (*.pll) must be
present on the Compact Flash card. These are used to control the sequence for all video
tracks.
The project and playlist file are created using DV Studio Advanced software. Using this
software, you can set simple sequences or complex sequences including “jump track“ or
“next track” actions. DV Studio can also program buttons with different function like “play”,
“stop”, “pause”, “mute”, “previous”, “next” and “volume”.
2. Simple play mode
In simple play mode, the user just copies all video files (.mpg) or JPEG files (.jpg) onto the
Compact Flash card. The MV-Flash M3+ will play these files in alphabetical sequence.
For MPEG still pictures or JPEG files, the play time can be set by the last digit of the
filename. (For example: APPLE5.mpg, where “5” means the track will be displayed for 5
seconds.) Note: Do not use the same filename on both MPEG and JPEG.
Note: Make sure all capital letters in filename defined in playlist are consistence with the
filename on CompactFlash card. All filename should be in 8+3 format (i.e. xxxxxxxx.xxx) and
avoid using any illegal characters like “~”, “_”, “-“, etc
OPERATING FUNCTIONS
The following key buttons are default in “Simple Play mode”
PLAY (Button 1)
•
•
•
Resumes playback of videos from track 1 after STOP has been pressed.
Resumes playback of the track from the point that it has been set to PAUSE.
Playback is reset back to the beginning of the specific track which is being played at
the time the PLAY button is pressed.
STOP (Button 2)
•
When STOP is pressed the video stops playing and a blank screen is displayed.
PAUSE (Button 3)
•
•
When PAUSE is pressed the video image instantly freezes.
Press Pause again or PLAY to resume normal playback from the position where it was
paused.
- 14 -
Download from Www.Somanuals.com. All Manuals Search And Download.
REPEAT (Button 4)
•
•
When REPEAT is pressed the current track loop back on itself continuously.
To disable the repeat mode press REPEAT, PLAY, PREVIOUS TRACK or NEXT
TRACK . When the track plays to the end it will playback the next track (and etc.) as
normal.
NEXT TRACK (Button 5)
The NEXT TRACK function can be activated only when a track is already playing.
•
When NEXT TRACK is pressed the current video stops playing and jumps directly to
the start of the next track.
VOLUME DECREASE (Button 6)
Decreases audio output volume setting.
•
VOLUME INCREASE (Button 7)
Increases audio output volume setting.
•
MUTE (Button 8)
•
•
When MUTE is pressed, all the tracks will have no sound.
Press MUTE again to resume the normal sound in all tracks.
Note : All above buttons can be re-defined by DV Studio Advanced software if operating in playlist mode.
- 15 -
Download from Www.Somanuals.com. All Manuals Search And Download.
8 Dimensions
146.77
5.07
91.
46
81.31
136.62
18
Unit in mm
The maximum thickness of the controller is 20.6mm with or without video add-on board (measured from bottom of
PCB to top of components, including any underside components & leads). We recommend clearances of:
•
5mm from bottom of PCB - if mounting on a metal plate we also recommend a layer of suitable insulation
material is added to the mounting plate surface.
10mm above the components
•
•
3~5mm around the edges
Any of the holes shown above can be used for mounting the PCB, they are 3.2mm in diameter.
CAUTION: Ensure adequate insulation is provided for all areas of the PCB with special attention to high
voltage parts such as the inverter.
- 16 -
Download from Www.Somanuals.com. All Manuals Search And Download.
9 Specifications
Playable formats:
MPEG-1 video (Video CD)
MPEG-2 video* (DVD)
MPEG-4 video (DivX format)
MPEG still picture
MP3 audio
JPEG still picture
VGA (640x480)
Video Storage
medium:
CompactFlash Memory Cards: Type 1 & Type 2
Output Display
Systems:
TV and Video Monitors
VGA monitors
Video Output:
Signal type: Composite and S-Video
Output format: PAL and NTSC
Low resolution : 352 x 288 pixels (PAL)
: 352 x 240 pixels (NTSC)
Output Resolution:
High resolution : 720 x 576 pixels (PAL)
: 720 x 480 pixels (NTSC)
Still picture
: 704 x 576 pixels (PAL)
: 704 x 480 pixels (NTSC)
: 800 x 600 pixels
JPEG picture
Audio Outputs:
Stereo output, connector – RCA jack, 3.2 V p-p max. 5K ohm
Signal-to-Noise:
Select Switches:
96 dB
Power ON/OFF select
PAL/NTSC select
Video/VGA select
Indicators:
Power On/Off LED
Status LED
Start-up Modes:
Power Input:
Autoplay (at power-on); Sleep mode (after power-on)
12V DC, 500mA typical
Power Consumption:
Environment:
Relative Humidity
Dimensions:
6 W
0 °C to 50 °C, free air circulation
5% - 95% relative humidity, non-condensing
146.8mm x 91.5 mm x 18mm (W x D x H)
135g
Net Weight:
External ports:
RS-232 port (option) – for barcode application.
Remote Ext.
– External buttons connection (8-buttons)
Video Storage
Accessories:
CompactFlash Card – various memory capacities available
64MB, 128MB, 256MB, 512MB, 1G, 2G, 4G
* For MPEG-2 video, the encoding rate is limited to 5Mb/s
- 17 -
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
The products are warranted against defects in workmanship and material for a period of one (1) year from the date
of purchase provided no modifications are made to it and it is operated under normal conditions and in compliance
with the instruction manual.
The warranty does not apply to:
•
Product that has been installed incorrectly, this specifically includes but is not limited to cases where electrical
short circuit is caused.
•
Product that has been altered or repaired except by the manufacturer (or with the manufacturer’s
consent).
•
Product that has subjected to misuse, accidents, abuse, negligence or unusual stress whether physical or
electrical.
Ordinary wear and tear.
•
Except for the above express warranties, the manufacturer disclaims all warranties on products furnished
hereunder, including all implied warranties of merchantability and fitness for a particular application or purpose. The
stated express warranties are in lieu of all obligations or liabilities on the part of the manufacturer for damages,
including but not limited to special, indirect consequential damages arising out of or in connection with the use of or
performance of the products.
CAUTION
Whilst care has been taken to provide as much detail as possible for use of this product it cannot be relied upon as
an exhaustive source of information. This product is for use by suitably qualified persons who understand the nature
of the work they are doing and are able to take suitable precautions and design and produce a product that is safe
and meets regulatory requirements.
DISCLAIMER: There is no implied or expressed warranty regarding this material.
LIMITATION OF LIABILITY
The manufacturer’s liability for damages to customer or others resulting from the use of any product supplied
hereunder shall in no event exceed the purchase price of said product.
TRADEMARKS
The following are trademarks of Digital View Ltd:
•
•
•
DigitalView
ThinSurfer
RemoteMedia
CompactFlash is a registered trademark of SanDisk Corporation.
Other brands and products are trademarks of their respective holder/s.
- 18 -
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTACT DETAILS
ASIA:
Digital View Ltd
19th Floor, Tai Tung Building
8 Fleming Road
Wanchai
Hong Kong
Tel: (852) 2861 3615
Fax: (852) 2520 2987
Technical Support: support@digitalview.com
EUROPE:
Digital View Ltd
36-38 Mortimer Street,
London
W1W 7RJ
UK
Tel: (44) (0) 20-7631 2150
Fax: (44) (0) 20-7631 2156
Sales: [email protected]
USA:
Digital View Inc.
18440 Technology Drive
Building 130
Morgan Hill, CA 95037
Tel: (1) 408-782 7773
Fax: (1) 408-782 7883
Specifications subject to change without notice
Document No. 9168900-10 (October 2005)
2005
© Digital View Ltd
- 19 -
Download from Www.Somanuals.com. All Manuals Search And Download.
|