INSTALLATION AND OPERATION MANUAL
Free-Standing
EPA Certified
Wood-Burning Stoves
Save These Instructions
For Future Reference
P/N 775,214M, Rev. C, 05/2008
Striker™ S160
Striker SA160
Wood Stoves
Model Striker™ S160
A French manual is available upon request. Order P/N 775,214CF.
Ce manuel d’installation est disponible en francais, simplement en faire la demande. Numéro de la
pièce 775,214CF.
Theseappliancesmustbeproperlyinstalledandoperatedinordertopreventthe
possibility of a house fire. Please read this entire installation and operation
manual before installing and using your wood stove. Failure to follow
these instructions could result in property damage, bodily injury or
evendeath.Contactyourlocalbuildingorfireofficialstoobtain
US
apermitandinformationonanyinstallationrequirements
Report # 050-S-03b-2
and inspection requirements in your area.
WARNINGS
• Hot! Do not touch! The glass and surfaces of this appliance will
be hot during operation and will retain heat for a while after
shutting off the appliance. Severe burns may result.
• Carefully supervise children in the same room as appliance.
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
General Safety Precautions .................................................................ꢀ
Testing Information...........................................................................4
Draft Requirements...........................................................................4
Selecting the Proper Venting System......................................................4
Negative Pressure Warning ................................................................5
Creosote........................................................................................5
Ash Disposal...................................................................................5
Fuel ............................................................................................5
Burn-In Period.................................................................................5
Paint Curing ...................................................................................5
Clearances to Combustibles ................................................................6
Floor Protection...............................................................................6
Reduced Clearances .........................................................................6
Alcove Clearances............................................................................6
Mobile Home Installations ..................................................................6
Chimney and Connector .....................................................................6
Components Required for Installation.....................................................6
Installation Clearances Diagrams..........................................................7
Leg and Heatshield Installation ............................................................8
Outside Air Kit Installation ..................................................................8
Stove Installation .............................................................................9
Pedestal Installation .........................................................................10
Post Installation Checks .....................................................................11
Brick Installation..............................................................................11
Optional Blower Installation ................................................................1ꢁ
Operating Hints ...............................................................................1ꢁ
Starting and Maintaining a Fire ............................................................14
Cleaning Glass ................................................................................15
Operating Techniques and Hints............................................................15
Getting the Most Out of Your Stove ........................................................15
Maximizing Your Stove’s Overall Efficiency ..............................................16
Achieving Clean, Long Burns ...............................................................16
Maintenance...................................................................................17
Troubleshooting...............................................................................18
Do’s and Don’ts ...............................................................................19
Replacement Parts List ......................................................................ꢀ0
Accessories....................................................................................ꢀ1
Product Reference Information .............................................................ꢀꢀ
ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
Testing Information
Selecting the Proper Venting System
This manual describes the installation and operation of the
Striker™ S160 non-catalytic wood heaters. These heaters meet
the U.S. Environmental Protection Agency’s emissions limits for
wood heaters sold on or after July 1, 1990. This heater has been
developed, tested and constructed in accordance with therequire-
ments of UL 1482, ULC S627 and HUD standards and is listed by
OMNI Test Laboratories, Beaverton, OR. It has been approved for
residential, mobile home and alcove installations.
The appliance is merely one component of a larger system. The
other equally important component is the venting system. This is
necessary for achieving the required flow of combustion air to the
firechamberandforsafelyremovingunwantedcombustionbyprod-
ucts from the appliance. If the venting system’s design does not
promote these ends, the system may not function properly. Poorly
functioningventingsystemsmaycreateperformanceproblemsas
well as be a safety hazard. A draft test should read greater than
.04’ W.C. (inches water column) and less than .08” W.C. As
per NFPA-211 standard (see paragraph below), the installer must
take into account all variables within the installation and install the
appliance in such a manner that satisfies the draft requirements
of the appliance. See Chimney Guidelines below to assist you in
selecting the proper venting system for your installation.
Draft Requirements
Yourwoodstoveisdependentuponaproperlyfunctioningchimney
for optimum performance. It is a high efficiency appliance that
loses much less heat up the chimney than older appliances and
fireplaces. For this reason it is important to match the stove to
the chimney. The chimney has two functions:
AmericanNationalStandardsInstituteANSI/NFPAꢀ11,Standard
for Chimneys, Fireplaces, Vents, and Solid Fuel-Burning Appli-
ances-SeeDraftSection: Achimneyorventshallbesodesigned
andconstructedtodevelopaflowsufficienttocompletelyremoveall
flueandventgasestotheoutsideatmosphere. Theventingsystem
shall satisfy the draft requirements of the connected appliance in
accordance with the manufacturer’s instructions.
1. It draws combustion air into the appliance (without air, no fuel
will burn) and
2. It exhausts combustion by-products. Your new Country™ Col-
lection stove is what is known as a “natural draft” appliance.
The appliance depends solely on the natural draft of the chimney
system to draw combustion air into the unit. Draft is the force that
moves air from the appliance up into the chimney. The amount of
draft in your chimney depends on the length of the chimney, local
geography, nearby obstructions and other factors. Too much draft
may cause excessive temperatures in the appliance (overfiring).
Slow or inadequate draft equals poor combustion and possible
smoking problems. The following are some conditions that may
contribute to poor chimney draft:
Chimney Guidelines:
• This appliance requires approximately 12 feet minimum of
“effective draw” provided by the venting system. As a rule of
thumb, every 90 degree total direction change in the venting
will result in a loss of approximately 5 feet of “effective draw.”
Example: If two 45 degree offsets are used, subtract 5 feet
from the actual vertical vent height to determine your “effec-
tive draw.” In this case if you had 14 feet of vertical vent, the
effective draw would only be approximately 9 feet (14 ft. - 5 ft.
= 9 ft.), therefore it may be necessary to add additional height
to the venting system.
1. A chimney too large for your appliance.
2. A chimney with not enough height to produce adequate
draft.
3. A chimney with excessive height (this may allow exhaust
to cool too much before exiting, which will stall the rate the
exhaust exits).
4. Offsets in the venting system are too restrictive (see Chimney
Guidelines).
• Do not install an offset within the first two feet above the flue
outlet on the appliance.
Inadequate draft will cause the appliance to leak smoke into the
room through the stove and the chimney connector joints.
• In well insulated and weather tight homes, it may be difficult
to establish a good draft up your chimney. The poor draft is
caused by a shortage of air in the house. In this situation an
Outside Air Kit may need to be installed (See Negative Pressure
Warning on Page 5 and Outside Combustion Air on Page 8).
Excessive draft may cause an uncontrollable burn or a glowing
red stove or chimney part.
Overfiring Damage - If the heater or chimney connector glows,
you are overfiring. Other symptoms may include: Cracking,
warping or burning out of components, plated doors may turn
color, stove glass may develop a haze, which will not come off
with cleaning.
Overfiring of a stove is a condition where excessive temperatures
are reached, beyond the design capabilities of the appliance. The
damage that occurs from overfiring is not covered under the
manufacturer’s limited warranty.
Also see Troubleshooting on Page 18.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Dry, seasoned wood is that which has been cut, split and allowed
to dry under a covered area where air is free to flow and circulate
under and around the wood (not under a tarp or plastic). Make
sure wood is not stacked directly on the ground, it may absorb
moisture from the ground. It should be allowed to dry in these
conditions for a minimum of six months, preferably one year
or more. IT MUST BE UNDERSTOOD THAT WOOD CANNOT BE
LEFT IN ANY KIND OF WET OR DAMP AREA OR IT WILL NEVER
BECOME COMPLETELY SEASONED.
Negative Pressure Warning
This appliance is not designed to be operated in a negative pres-
sure. Very airtight homes with large kitchen exhaust fans, or
homes with furnace cold air returns located in close proximity
to the wood stove or fireplace insert may create negative pres-
sure in the same room as the heating appliance. This can create
dangerous back drafting of the stove and chimney joints, drawing
combustion by-products into the home. Be sure your home has
adequate makeup air to eliminate negative pressures caused by
the above-mentioned sources. Outside air connected to the ap-
pliance probably will not resolve such a problem as the stove or
fireplace insert is not the source of negative pressure. Lennox
Hearth Products accepts no liability for damages resulting from
negative pressures described here.
Your stove will not operate at the level that it is meant to unless
you use seasoned, dry wood. Do not burn driftwood or wood that
has been in salt water, doing so will void your warranty. Do not
burn treated wood, coal, garbage, cardboard, solvents, or colored
paper. Burning treated wood, garbage, solvents, or colored paper
may result in the release of toxic fumes. This type of burning will
also void your warranty.
Ventilation Requirements - Provide adequate air for combustion.
The fresh air requirements of this appliance must be met within
the space where it will be installed. Ventilation is essential when
using a Solid-Fuel-Burning heater. In well insulated and weather
tight homes, it may be difficult to establish a good draft up the
chimney (caused by a shortage of air in the home). The lack of air
is caused by many common household appliances which exhaust
air from the home (such as a furnace, heat pump, air conditioner,
clothes dryer, exhaust fans, fireplaces, and other fuel burning ap-
pliances).Also,thecombustionprocessofthisheaterusesoxygen
from inside the dwelling. If the available fresh air delivery in the
dwellingisinsufficienttosupportthedemandsoftheseappliances,
problems can result (i.e. excessive negative pressure can develop
in the dwelling which will affect the rate at which this appliance
can draft thus resulting in performance problems. To correct this
problemitmayhelptoopenawindow(preferablyonthewindward
side of the house) or install an optional outside air kit.
Burn-In Period
If your stove has a Gold or Nickel-Plated Door, be sure to clean
it with a household type glass cleaner and a very soft cloth to
remove any fingerprints and residues prior to the first fire and
before any fire if the gold has been handled or soiled. Do not
close the door tightly during the “Burn-In Period.” Also, open
the door frequently (every 5-10 minutes) to keep the gasket
from adhering to the curing paint. Ventilate the house well dur-
ing these first firings as the paint gives off carbon dioxide and
unpleasant odors. It is recommended that persons sensitive to
an imbalance in the indoor air quality avoid the stove during the
curing process.
Pleasebepatientwiththeheatoutputofyourstoveforthefirstfew
weeks. The steel will go through a curing process that eliminates
moisture,whichisdeepinthesteelandfirebrick.Thismoisturewill
reduce initial heat output of your stove and may make it difficult
to start. After you have broken in the paint on the stove it will be
necessary to build hot fires to thoroughly remove the moisture
from the appliance. Running the stove with the draft fully open
for 1 to 1-1/2 hours after starting and adding generous amounts
of fuel during the first week or two should complete the curing
process. We recommend the use of a thermometer attached to
the stovetop or chimney. Temperatures on the connector pipe
should run in the 250-600 degree range. (DO NOT OVERFIRE THE
STOVE DURING THIS PROCESS. IF THE STOVE OR CHIMNEY
BECOMES RED, REDUCE THE AMOUNT OF AIR ENTERING THE
STOVE IMMEDIATELY).
Creosote
CreosoteFormationandNeedforRemoval-Whenwoodisburned
slowly, it produces tar and other organic vapors, which combine
with expelled moisture to form creosote. The creosote vapors
condense in the relatively cool chimney flue of a slow-burning fire.
As a result, creosote residue accumulates on the flue lining. When
ignited, this creosote makes an extremely hot fire. The chimney
and chimney connector should be inspected at least once every
two months during the heating season to determine if a creosote
build-up has occurred. If creosote has accumulated, it should be
removed to reduce the risk of a chimney fire.
Ash Disposal
Paint Curing
Ashes should be scooped out of a cool stove with a small metal
shovel. Ashes should be placed in a metal container with a tight
fitting lid. The closed container of ashes should be placed on
a non-combustible floor or on the ground, well away from all
combustible materials, pending final disposal. If the ashes are
disposed of by burial in soil or otherwise locally dispersed, they
should be retained in the closed container until all the cinders
have thoroughly cooled. Ashes can ignite up to 72 hours after
removal from the stove.
Your new Striker™ S160 wood stove is painted with a high tem-
perature paint that cures during the first few firings. We recom-
mend that you put your stove through a regimen of three burns.
The first two should last for 20 minutes each at 250 degrees (the
stove should be allowed to cool completely between each burn).
The third should be a burn of at least 450 degrees F. for 45-60
minutes. The paint will become soft, gummy and emit non-toxic
smoke during these burns. After the stove cools down for the third
time, the paint will harden. DO NOT BUILD A LARGE ROARING
FIRE UNTIL THIS CURING EFFECT IS COMPLETE OR YOU MAY
DAMAGE THE FINISH OF YOUR STOVE. Spray can touch-ups
should be done only with a high temperature stove paint (cat. no.
70K99), available from all Lennox Hearth Products dealers.
Fuel
This unit is designed and engineered to burn, dry, well-seasoned
wood only.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Approved Chimney* - Your stove is approved for use with Class
A, UL 103 HT (U.S.) / ULC-S629 (Canada) Listed Residential Type
and Building Heating Appliance Chimney (HT chimney - 2100°
Fahrenheit) and double wall connector pipe from Security™
Chimneys.
Clearances to Combustibles
WARNING: BEABSOLUTELYSURETHEDISTANCEBETWEEN
THE HEATER AND THE SURFACE OF ANY COMBUSTIBLE
CONSTRUCTION IS NOT LESS THAN SHOWN.
Clearances to connector shall be measured from 6" flue collar.
Restrictions apply! Read instructions before installing.
Floor Protection
USA - The floor in front and under the heater must be protected
with a minimum of 3/8” (10 mm) thick noncombustible material.
The covering must extend 16” (406 mm) in front of the door
opening of the heater and 8” (203 mm) to either side of the door
opening and 5-1/2” (140 mm) to the rear or to the wall, whichever
is smaller. In all installations a 16” (406 mm) minimum hearth
extension (in front of the stove) is required as measured from the
door opening of the unit.
Chimney and Connector
Minimum 6" diameter, minimum 24 MSG black steel connector
pipe with listed factory-built chimney suitable for use with solid
fuels or masonry chimney. Horizontal connection not tested, refer
to local building codes for installation. Restrictions apply! Read
instructions before installing.
Canada - The floor in front and under the heater must be protected
with a minimum of 3/8” (10 mm) thick noncombustible material.
The covering must extend 457 mm in front of the door opening of
the heater and 200 mm to either side of the stove body and 200
mm to the rear or to the wall, whichever is smaller. In all installa-
tions a 457 mm minimum hearth extension (in front of the stove)
is required as measured from the door opening of the unit.
Clearance dimensions are to 6” (152 mm) flue collar. If a single
wall connector pipe with shield is used, a 1 inch air space is
needed between pipe and shield. Shield attaches to rear of stove
pipe and must run from stove top to ceiling. Pipe shield shall be
UL listed.
Residential chimney systems must be from the same brands as
listed for mobile homes but connector pipe may be double wall,
single wall or single wall with shield as listed above.
Reduced Clearances
Clearancestocombustiblesurfacescanbereducedwiththeuseof
listed double wall connector pipe. See the clearances with double
wall pipe on the following page.
Connector pipe and chimney must be of the same brand.
Thechimneyconnectorshallnotpassthroughanatticorroofspace,
closet or similar concealed space, or a floor, or ceiling. Where
passage through a wall, or partition of combustible construction
is desired, the installation shall conform to CAN/CSA-B365.
Alcove Clearances
Single Wall Pipe - Minimum 48" (1219 mm) width, maximum 48"
(1219 mm) depth. Minimum ceiling height is 84” (2134 m).
There must be an effective vapor barrier at the location where
the chimney or other component penetrates to the exterior of the
structure. Follow the vent manufacturer's detailed instructions.
DoubleWallPipe-Minimum44"(1117mm)width, maximum48"
(1219 mm) depth. Minimum ceiling height is 72” (1829 mm).
IMPORTANT NOTE: See Draft Requirements and Selecting a
Proper Venting System on Page 4 to assist you in choosing the
proper venting system for your installation.
Mobile Home Installations
This appliance is approved for installation into a mobile home
in the USA ONLY!
Components Required For Installation
Installation should be in accordance with the Mobile Home
Construction and Safety Standard, Title ꢀ4 CFR, Part ꢁꢀ80 (in
Canada CAN/CSA Zꢀ40 MH), or, when such a standard is not
applicable, the Standard for Mobile Home Installations, ANSI
Aꢀꢀ5.1.
Legs AND Bottom Heat Shield or Pedestal Base.
WARNING: In the event that you remove the blower for any
reason, make sure a cover plate (available from Lennox Hearth
Products) is installed before using the heater. Excessive rear
wall temperatures will result if the stove is burned without the
cover plate. Note: The cover plate is not necessary if a blower
has never been installed because a knock-out will be in place
to act as the cover.
All mobile home installations require an outside air kit (cat. no.
71111 or 71112). The stove must be bolted to the floor and
grounded to the chassis of the mobile home.
WARNING: DO NOT INSTALL IN SLEEPING ROOM OF A
MOBILE HOME.
* Other approved chimney brands are Projet, Jakes Evans/GSW,
Dura-vent, Metal Fab, Ameri-Tec, Metalbestos and Industrial
Chimney (ICC).
CAUTION: THE STRUCTURAL INTEGRITY OF THE MO-
BILE HOME FLOOR, WALL AND CEILING/ROOF MUST BE
MAINTAINED.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Clearances - Refer to Diagrams A, B and C
PIPE
INSTALLATION
A
B (1)
14”
C
D (1)
1ꢀ-1/ꢀ”
E†
8”
F (1,4)
9-ꢁ/4”
G (4)
6” Single
Wall
Residential or
Alcove
USA-16”
USA-ꢀ1”
USA-18”
CAN-48ꢁmm ꢁ56mm CAN-610mm ꢁ18mm ꢀ00mm ꢀ48mm CAN-5ꢁꢁmm
6” Single w/ Residential or
USA-10”
CAN-ꢁꢁ0mm ꢀ00mm CAN-5ꢁꢁmm ꢀ41mm ꢀ00mm 140mm
USA-10” 8” USA-18” 9-1/ꢀ” 8” 5-1/ꢀ”
8”
USA-18”
9-1/ꢀ”
8”
5-1/ꢀ”
USA-1ꢁ-1/ꢀ”
CAN-419mm
Pipe Shield
Alcove
6” Double
Wall
Residential or
USA-1ꢁ-1/ꢀ”
CAN-419mm
Alcove or Mobile CAN-ꢁꢁ0mm ꢀ00mm CAN-5ꢁꢁmm ꢀ41mm ꢀ00mm 140mm
Home*
PIPE
INSTALLATION
H (ꢀ) I (6)
USA-ꢁꢁ-ꢁ/4” USA-47-ꢁ/4”
J (ꢀ)
USA-ꢁꢁ-1/ꢀ”
K
L (5)
USA 0"
M
Single Wall Residential or
Alcove
USA-16”
84”
ꢀ1ꢁ4mm
CAN-ꢀ00mm
CAN-1111mm CAN-1ꢁ40mm CAN-100ꢁmm CAN-450mm
USA-ꢁꢁ-ꢁ/4” USA-41-ꢁ/4” USA-ꢁꢁ-1/ꢀ” USA-16”
CAN-1111mm CAN-1188mm CAN-100ꢁmm CAN-450mm
USA-ꢁꢁ-ꢁ/4” USA-41-ꢁ/4” USA-ꢁꢁ-1/ꢀ” USA-16”
CAN-1111mm CAN-1188mm CAN-100ꢁmm CAN-450mm
Single w/
Pipe Shield Alcove
Residential or
USA 0"
CAN-ꢀ00mm
84”
ꢀ1ꢁ4mm
Double Wall Residential or
Air-Cooled Alcove or Mo-
bile Home*
USA 0"
CAN-ꢀ00mm
7ꢀ”
18ꢀ9mm
PIPE
INSTALLATION
Nu
Pu
T (6)
† USA=8" (ꢀ00mm) from door opening,
Canada=8" (ꢀ00mm) from sides and back
of unit
Single Wall Residential or
Alcove
ꢁ0"
76ꢀmm
ꢁ6"
914mm
USA-58-1/ꢀ”
CAN-1645mm
USA-5ꢀ”
Single w/
Residential or
ꢁ0"
ꢁ6"
u
Dimensions to Stove Body
Pipe Shield Alcove
76ꢀmm
914mm
CAN-1486mm
USA-5ꢀ”
CAN-1486mm
Double Wall Residential or
Air-Cooled Alcove or Mo-
bile Home*
ꢁ0"
76ꢀmm
ꢁ6"
914mm
* Mobile Home - USA only
Diagram A: Top View-Parallel Installation
Diagram B: Side View-Alcove & Parallel Installation
48”
Maximum
Depth
A
B
E
L
C
D
N
P
72" Min.
I
6” Ø
Flue Collar
H
M
†
E
*L
Floor Protection
†
E
K
J
Floor Protection
I
Footnotes:
F
F
G
G
1- These dimensions to the stove body are for reference only. Actual
distances should be measured from the stove’s flue collar.
2- Minimum noncombustible hearth pad dimensions.
3- Shield shall be attached to the rear of the stove pipe with a 1” air
space and must run from the top of the stove to the ceiling.
4- Not applicable to alcove installations.
T
5- In corner applications, when installed at minimum back wall clear-
ances, the required floor protection is dimensioned off the back
plane of the stove, therefore the floor protection required off the
back corners (at a 45 degree angle) only needs to extend to the
wall. This situation will only occur in CANADA installations.
6- Reference dimension only, to assist in planning the installation.
H
Diagram C: Top View -
Corner Clearance,
Stove and Flue to Wal
l
Floor Protection
K
Clearances to connector pipe shall be measured from the flue
collar of the stove.
J
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Leg and Heatshield Installation
Note: The threaded rods used to bolt the legs to the stove are
packaged with the heatshield, as a heatshield is required when
a stove is installed on legs.
Residential and Mobile Homes
(Bolting down and grounding of stove are required only in
mobile homes).
Heat Shield
Mounting Holes
Open all cartons, if any and remove the contents upon receipt
and check for any damaged or missing parts. If there is hidden
damage, notify your freight company or Lennox Hearth Products
dealer immediately.
CAUTION: Wear gloves during installation in case of
sharp edges on the stove.
Front
Figure 2
Air Channel
Leg Installation
Outside Air Kit Installation
1. Carefully place stove on its back. Be careful not to scratch
the stove, use a piece of cardboard or carpet to protect
the back of the stove.
To install the “Outside Air Kit,” position the clip so that the nut is
directly above the hole punched in the back of the heatshield (See
Figure 3). Install the outside air adapter box on the stove by slid-
ing it into the air channel located between the bottom heatshield
and the stove bottom until the oblong ring is approximately 1/4”
from the rear edge of the lower heatshield. Make sure the ring is
facing down. Thread the 1/4” bolt up through the nut in the clip
until snug against the adapter box.
2. Mount all four legs as shown in Figure 1.
3. First, screw the threaded rods into the holes at the four
corners on the bottom of the stove. Screw the threaded
rods into the firebox three full rotations or 3/16 to 1/4”
(if the rear rods are screwed in too far they will lift the
bricks off the bottom of the stove). Use a washer and nut
to secure the leg. Be sure the legs are mounted squarely
on the firebox bottom. Tighten nuts securely.
Expanded View of Clip
4. Usethetwoboltsandwashersprovidedwiththeheatshield
kit to mount the heatshield as shown in Figure 2.
5. Do not over tighten the heatshield mounting bolts as it
may bend the heatshield.
Line up the hole in the clip with the hole in the
rear center of the bottom heatshield
Threaded
Rod
Washer
Nut
Clip
1/4” Bolt
Figure 3
To locate the hole in the hearth for outside air, mark a 4” circle on
the hearth. The circle’s center should be 2-3/4” directly back from
the center of the flue outlet and 5/8” to the left side.
Figure 1
8
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Download from Www.Somanuals.com. All Manuals Search And Download.
11. For residential installations, install the first section of stove
pipe with the crimped end going down inside the flue collar
on the heater. Continue with your stove pipe, installing each
section-crimped end down. Make the final connection to your
chimney. Your dealer carries the necessary pipe and fittings
to connect to the various listed factory-built chimneys. YOUR
CHIMNEY INSTALLATION MUST COMPLY WITH LOCAL
BUILDING AND FIRE CODES.
12. Be sure to fasten each stove pipe connection with at least 3
sheet metal screws.
13. Install chimney as per manufacturer’s instructions. Some
brands of pipe may require removal of the spacer ring in the
flue collar.
14. All horizontal runs of pipe should be as short as possible and
are required by NFPA No. 211 to have an upward pitch or rise
in the same direction the smoke travels of no less than 1/4”
to the linear foot. The connector pipe must meet minimum
clearances in any direction to walls or other combustible
materials. It must attach to a listed double wall metal chimney
at least 6” in diameter or to a masonry chimney with a flue
passage of at least 48 square
Stove Installation
1. If not previously installed, install floor protection and move
the heater into the desired location.
2. Position the stove on your floor protection in the exact location
where it is to be located, making sure all minimum clearances
are met.
3. If you are installing outside air on your stove, mark a 4” circle
on the floor protection just below the oblong ring. When
cut out, this hole will accommodate the flexible outside air
tube.
4. If the stove is to be fastened to the floor, locate the hold down
brackets inside the leg box and mark the floor protection
below the holes in the brackets.
5. If you are installing outside air on your stove, remove the
stove and cut the floor protection and the floor where the
4” air tube circle had been previously drawn. If the stove is
to be fastened to the floor, drill 1/2” holes through the floor
protection only, at the marks that were for fastening the
stove to the floor if so desired. Slip the flexible outside air
tube through the hole in the floor, leaving 1” of tube above
the floor protector surface, using tape to hold it in place.
6. Place the stove on the floor protection so that the previously
cut or drilled holes line up. Attach the stove to the floor with
the lag bolts if so desired.
inches.
15. It is required that a chimney
connector pipe not extend
further than the inner wall of
the flue when it is connected
to a masonry chimney and
that it either be cemented to
the masonry or be installed
without cement in a thimble
connected to the masonry
wall. When the connector is
inserted into a thimble, the
7. If you are installing outside air on your stove place the hose
clamp over the flexible air tube and slide the tube up over the
4” ring on the outside air adaptor box and tighten the hose
clamp. Push the outside air adaptor forward 1/4” until full
contact is made with the lower heatshield. Tighten the 1/4”
bolt until the adaptor box is held firmly in place. Use silicone
sealant to create a seal between the flexible air tube and your
floor protection.
joint must be tight enough so
that it will not be dislodged in
normal use.
Installconnectoratnolessthan
8. If it is necessary to level, secure or ground your stove, use
the holes in the bottom of the leg for those applications. To
level the stove on Olympic cast legs, locate the front leg that
is not touching the hearth pad. Insert the allen head screw
through the slotted washer (supplied with the legs) and into
the threaded hole in the bottom of the leg. See the drawing to
the right. Push the slotted washer down until it touches the
hearth pad and then tighten the screw into the leg. Should any
other leg not be resting on the hearth pad, install a washer
and screw in that leg as well.
Insert the allen
head screw
through the
slotted washer
the minimum clearances from
the ceiling when using a 90-
degree elbow to pass through
combustible constructions.
16. Chimney connector pipes
Figure 4
should never pass through a
floor, ceiling, fire wall, partition, or combustible construction
of any type unless certain precautions are taken. The best
method is to use a listed thimble and a listed chimney in
accordance with the manufactures directions. NFPA No. 211
gives approved methods for passing a flue pipe through
combustible constructions.
9. Install bricks and baffle as per instructions on Page 11. It is
highly recommended that the baffle be assembled before the
chimney is installed so that the insulating fiber blankets can
be adjusted into place through the flue collar.
10. If installed into a mobile home, the stove shall be grounded
to the mobile home chassis with a #8 AGW copper wire or
equivalent.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
5. If required, install the Outside Air Kit (cat. no. 71112) as
per the following instructions. To locate the hole in the
hearth for outside air mark and cut a 4” (102 mm) hole in
thehearth. Thehole’scentershouldbe3”(76mm)directly
forward from the center of the flue outlet or locate as per
the instructions below.
Pedestal Installation
(For ash drawer pedestal see instructions included with pedestal)
Residential and Mobile Homes
(Bolting down and grounding are required only in mobile homes)
6. Position the stove on your floor protection in the exact
locationwhereitistobelocated,makingsureallminimum
clearances are met. Mark the floor protection where the
pedestal will be located, then remove the stove.
CAUTION: Wear gloves during installation in case of
sharp edges on the stove.
1. Remove the heater from the carton, if packaged, upon
receipt and check for any damaged or missing parts.
7. Make four 1-1/2” (38 mm) cuts in one end of the corru-
gated tube and fold the flaps back. Cut a 4” (102 mm) hole
through the floor protection and the floor and insert the
corrugated tube into the hole. Cover it with the supplied
screen and fasten it to the floor protector.
2. Carefully put the stove on pedestal with the open end of
the pedestal facing the rear. DO NOT LEAVE THE STOVE
UNATTENDED UNTIL IT IS BOLTED SECURELY TO THE
PEDESTAL.
8. Locate the 11-1/2” x 14” (292 mm x 356 mm) metal plate
and paint to match the stove if necessary. Position this
piece so that the 14” (356 mm) dimension evenly overlaps
the lips on the back of the pedestal (see drawing below).
Attach this plate to the back of the pedestal with the self-
tapping screws supplied.
3. Line up the holes in the brackets on the pedestal with the
threaded holes in the bottom of the stove. Use the two
1/2”longboltsand3/8”standardwasherstoboltthestove
to the pedestal. Be sure to see that the stove is mounted
squarely on the pedestal before tightening the two bolts
securely.
9. If the stove is to be fastened to the floor, attach the stove
with the supplied lag bolts, through the pedestal base
on opposite sides, attaching them into the floor beneath
the floor protection. Seal any irregularities with silicone
sealer.
4. When installing a pedestal on this stove you MUST plug
the four leg mounting bolt holes, located on the bottom
of the stove in the four corners, with the bolts that were
usedtomounttheshippinglegs.Thetworearboltsshould
not be installed more than two full rotations to prevent
lifting the bricks off the bottom of the stove. FAILURE TO
INSTALL THESE FOUR BOLTS PROPERLY WILL RESULT
IN REDUCED CONTROL OF THE STOVE’S COMBUSTION
SYSTEM!
10. If installed in a mobile home, the heater shall be grounded
to the chassis with a #8 AGW copper wire or equivalent.
11. Install bricks as per instructions on Pages 11 and 12. It is
highly recommended that the baffle be assembled before
the chimney is installed so that the ceramic fiber blankets
can be adjusted into place from the flue outlet.
12. Install chimney as per manufacturer’s instructions.
Block Off Plate is
Required When
Installing Outside
Air Into Unit (Plate
is Included With
Kit # OAK-P)
Figure 5
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Post Installation Checks
Brick Installation
CAUTION: Wear gloves during brick installation in
case of sharp edges inside the stove.
1. Check that all chimney pipe joints are securely fastened.
2. Check that the heater is securely fastened to the floor (if
applicable).
Note: Installation of the baffle bricks and insulating blanket is
easier when you can still access the flue outlet, (before connecting
the flue pipe). Be sure the insulating blanket is placed flat on
the bricks so as not to block the flue. Use a ruler or a piece of
kindling to reach over the blanket to be sure it is completely flat
on top of the baffle bricks.
3. Make sure the intake vent has clear access to outside air
(if applicable).
4. Make sure the outside air vent has been sealed properly
to keep rodents out (if applicable).
Measure bricks before installing, as per list of dimensions on
next page, to be sure the correct bricks are installed in the cor-
rect location.
5. Be sure all roof flashings are watertight.
6. Be sure the stove is properly grounded (if applicable).
1. Install bricks #1-18 in the numbered sequence shown in
Figure 6 on Page 12.
FOR YOUR OWN PROTECTION AND INSURANCE
PURPOSES,HAVEYOURCHIMNEYANDCONNECTOR
PIPE INSTALLATION INSPECTED BY YOUR LOCAL
BUILDING CODE AUTHORITY OR FIRE MARSHAL
BEFORE STARTING A FIRE IN YOUR STOVE. NOTIFY
YOUR INSURANCE COMPANY.
2. Next, install bricks #19 and 20 into the rear stainless steel
baffle support (see Figures 7 and 8 on Page 12).
11
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Next, install baffle bricks #21-24 by sliding the back of
each brick over the center tube and support until the front
of the brick clears the front tube and support. Then lift
the front of the brick above the front support and tube
and slide it forward as far as it can go (very important),
it will hit the front of the stainless support when it is fully
forward. The rear of the bricks sit on top of bricks #19-20
(Figures 7 and 8).
4. Carefully slip the ceramic blanket up over the front of
the front stainless support and bricks #21-24. Grasp the
edge of the blanket and slide it back until the front of the
blanket is flush to the front of bricks #21-24 (Figure 7).
Shake the blanket gently from side to side to get it to lay
flat. Be sure the ceramic blanket is directly on top of the
baffle bricks and that it does not hang out past the front
of the baffle as shown in Figure 7, also see note on Page
11.
17D
18B
Brick Sizes
8
A
9
F
10
F
7
F
4
F
1
F
A = 4-1/4” x 9”
B = ꢀ-1/4” x 8-7/8”
C = ꢁ-1/ꢀ” x 9”
D = ꢀ-1/4” x 9”
5
F
2
F
6
3
E = 1-1/ꢀ” x 8-7/8”
F = Full Brick (4-1/ꢀ” x 9”)
G = 1-1/ꢀ” x 9”
D
D
11F
13F
14F
12A
H = ꢁ-1/ꢀ” x 8-7/8”
15G
16E
Figure 6
Ceramic Fiber
Blanket
Baffle Bricks Top View
19 C
ꢀ0 H
Stainless
Steel Baffle
Supports
ꢀꢁ F
ꢀ1 F
ꢀꢀ A
ꢀ4 F
Figure 8
Figure 7
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
1ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Plug in the fan speed control into the nearest outlet, then
plug the blower cord into the speed control. Do not route
the fan power cord under the stove or allow it to come in
contact with any surface of the stove. Read the section
Starting and Maintaining a Fire for proper fan operating
instructions on Page 15.
Optional Blower Installation
A blower, catalog number 71000, can be installed on the stove
to improve hot air distribution throughout the room.
To install the blower:
1. Remove all the contents from the blower box. Included
with the blower should be a blower speed control.
2. Remove the screws in the round knock-out plate on the
back of the stove. Bend the knock-out plate back and forth
until it can be removed.
3. Mount the blower as shown below. Make sure the cord is
at the bottom when mounted and that it does not touch the
stove anywhere. Remove the four screws from the back of
the stove. Use one of the four screws with a washer on it
and attach the blower through one of the four mounting
legs on the blower housing. Check to make sure that the
fan blade does not touch the large hole in the rear heat-
shield. (Spin it to check all directions). Finish attaching
the blower with the other three screws. Tighten the screws
moderately tight but do not over tighten as you may strip
the holes out.
WARNING:Intheeventthatyouremovetheblowerfor
any reason, make sure a cover plate (available from
Lennox Hearth Products) is installed before using the
heater. Excessive rear wall temperatures will result
if the stove is burned without the cover plate. Note:
The cover plate is not necessary if a blower has never
been installed because a knock-out will be in place
to act as the cover.
Operating Hints
1. Burn only dry, well-seasoned wood for maximum heat
output. In some states it is illegal to burn wet wood or
anything other than clean, dry wood products.
2. Your stove is designed to operate with the door closed!
Operate only with the door shut tightly at all times except
when loading wood.
3. DO NOT hit or move the baffle brick while loading wood.
Occasionally check the baffle. Make sure the insulating
blanket is always flush with the front of the baffle brick.
Loading oversized logs may dislodge the baffle bricks.
4. CAUTION: THE DRAFT CONTROL MUST BE FULLY OPEN
BEFOREOPENINGTHEDOORTOAVOIDPOSSIBLECOM-
BUSTION FLASH!! (Ignition of hot volatile gases as the
door is opened).
5. Feeding excessive amounts of fuel to the stove should be
avoided. Itisimportanttosupplyitwithsufficientdraftand
fuel to maintain a moderately hot fire. If, during overnight
burns, heavy creosote deposits develop inside your stove
and on the door, the draft is set too low - review your
burning habits!
Figure 9
WARNINGS
The blower must be plugged directly into a properly
groundedthree-prongreceptacle,1ꢀ0VAC,60Hz,single
phase. Do not cut or remove the grounding prong from
this plug. Do not route power cord under or in front of
appliance.
CAUTION
Be careful not to abuse door assembly by striking or
slamming it. If the door assembly or glass is broken or
damaged, they must be replaced with factory original
parts before heater can be safely operated. Use only
components provided by the manufacturer as replace-
ment parts.
Installation must be in accordance with National Elec-
trical Code, ANSI/NFPA 70 - latest edition. In Canada,
the current CSA Cꢀꢀ-1 Canadian Electrical Code - latest
edition.
DANGER: Disconnect power before servicing blower.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
1ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Light the paper and allow sufficient time for the kindling to
become fully engulfed in flames. Close the door. Your door may
or may not need to be left slightly open during this process,
depending on your stove model and chimney draft. Once
the kindling is burning well, larger pieces of wood may be
added, then the door should be closed.
Do not operate the stove with the doors open or ajar, as
this will produce extreme temperatures within the stove.
Damage caused from over-firing is not covered under the
manufacturers limited warranty.
5. For best results, use smaller pieces of wood to get the
stove temperature very high before loading larger wood
for sustained burns. If necessary, crack the door to allow
ignition of the fuel charge. Now you can add larger pieces
of wood and after several minutes of high burn, set the left
control for the desired heat output. Check the exhaust in
about 15 to 20 minutes. Large amounts of smoke indicate
animproperburnsetting(eithertoohighortoolow).Adjust
and recheck in 5 to 10 minutes.
6. After your stove has been thoroughly preheated, your
blower can be switched on. When refueling your stove,
turn the blower off for the first 30 minutes. On low and
medium-lowburnsrunthebloweronlow.Theseburnrates
wouldbeachievedbyoperatingthestovewiththedraftrod
fully pushed in to up to 3/4” open (out). To do this, turn
on the blower at the speed control and rotate the control
all the way to the right. On medium-high and high burns
you may run the blower on high. These burn rates would
be achieved by opening the draft rod further than stated
previously. To do this, turn on the blower with the speed
control and do not rotate the switch after it clicks on.
Figure 10
Starting and Maintaining a Fire
BesuretocleantheNickelorGoldPlateddoorwithahousehold
type cleaner and a very soft cloth to remove any fingerprints
and residues prior to the first fire.
1. NEVER USE FLAMMABLE LIQUIDS TO START OR RE-
KINDLE A SOLID FUEL FIRE!!
2. Fully open the primary draft control by pulling the 1”
plastic knob out on the left side (lower front corner) until
it stops (away from the stove). This control determines
the amount of air entering the stove. Pushing it toward
the stove reduces the burn rate in the firebox. For your
convenience, the rod on this control is marked with
four grooves to assist you in obtaining repeatable burn
rates.
3. Place a small amount of crumpled paper in front of the
firebox and cover it with a few pieces of kindling.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning Glass
CAUTION
SEE MAINTENANCE ON PAGE 17 FOR GLASS CLEANING TIPS
Cleaning Glass: Ensure appliance is cold prior
to cleaning glass. A commercial glass cleaner
designed for stoves is recommended. Do not use
abrasivecleaners.Donotcleanwithanymaterials,
which may scratch or otherwise damage the glass.
Scratches on the glass can develop into cracks or
break. Inspect the glass regularly. If you detect a
crack, extinguish the fire and contact your dealer
for a replacement.
Theoperatorplaysanimportantpartinkeepingtheglasscleanand
free of build-ups. The first and most important part the operator
plays is making sure to burn only well-seasoned firewood. Wet
wood = Dirty glass. Keeping your glass door clean is partly ac-
complishedbytheairwashsystemofthestove,whichsendsclean,
fresh air for combustion, over the window before it enters the fire.
The high temperatures inside the firebox also keep the glass clean.
No stove door stays perfectly clean. The following are methods
for keeping build-up on your glass to a minimum. When properly
installed and operated by a knowledgeable operator, your glass
door should require very little maintenance. Do not expect to get
extremely long burn times and keep the window perfectly clean.
Cool temperatures cause condensation of unburned volatiles on
the glass. If your glass gets very dirty during overnight burning,
try preheating the stove a little longer before damping it down for
an overnight burn. Also, don’t damper your stove down as low
because you’ll get more heat for your money by burning a little
hotter for a slightly shorter time.
Operating Techniques and Hints
Recent developments in wood-burning technology have made
wood-burning a cleaner and more convenient way to heat your
home.Overallefficiencyinawood-burningapplianceisacombina-
tionofcombustionefficiencyandheattransferefficiency. Whether
heatingyourentirehome,orjustaroomortwo,yourunderstanding
of how to best operate your stove or insert will enhance its overall
efficiency and performance. What this can mean to you is longer,
cleaner burns, less wood use and more heat.
The air wash system will perform at its best at medium burn rates.
Some stove models will self clean by burning very hot fires but
be sure not to over-fire the stove. If it glows red it is over-fired.
Over-firing a stove also causes the window to soot up. Extremely
hot fires with fresh wood may cause the flow rate to exceed one
foot per second, which is as fast as a flame can burn. This is why
a candle goes out when you blow on it. Blow on it gently and it
burns brightly. Blow on it hard and it goes out. This will cause
excessive exhaust emissions and your window to soot up, as the
stove is unable to burn the gases emitted from the wood. Try
slowing the stove down a little by closing the damper somewhat
as it warms up.
Getting the Most Out of Your Stove
The following sections will outline techniques you can use to “get
the most out of your stove.” Please read them carefully.
Keeping freshly loaded wood away from the window will also help.
Load fresh logs in the rear of the firebox. Build-up tends to occur
first on the right side of the window. This is caused by the swirl-
ing motion of the exhaust gases similar to water running down a
drain. Keep fresh logs further back on the right side of the firebox
to help prevent this problem.
Understanding how your Country™ Collection stove works should
help you keep your glass door very clean, but as stated: no glass
door stays perfectly clean. We hope this information is helpful in
keeping your glass door clean so that you may enjoy many hours
viewing your high efficiency stove. For more information, contact
your Lennox Hearth Products dealer.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Thoroughly preheat your stove before slowing the burn
rate by closing the draft control.
Maximizing Your Stove’s Overall Efficiency
2. Measure the stove temperature at the hottest point on
the stove top or face. Use this information to repeat burn
rates.
3. Once preheated, add wood (if needed) and partially close
the draft control (lower left).
It is important to know that for high, combustion efficient, clean
burns, you will need to have sufficient temperatures inside the
fireboxforthoroughcombustion.Thebestmethodfordetermining
if you have sufficient temperatures is to watch the brick lining in
your firebox. When you first light your stove, the bricks will turn a
dark brown or black. After 20 to 30 minutes of a hot fire, most of
the bricks should return to near their original light brown or yellow
color. Thismeansthebrickshavereachedahighenoughtempera-
ture for your stove to achieve high combustion efficiency.
4. Operate your stove as much as possible in the low to
medium burn ranges.
5. Do not lower the draft setting so low as to completely ex-
tinguish the flames in the firebox. Check for at least some
small flames 20 minutes after setting the draft control.
6. Do not continually operate your stove in the high (wide
open) setting. This wastes wood by carrying a great deal
of heat up the chimney and can damage your stove and
chimney.
7. Go outside and check your chimney. More than a very
small amount of smoke indicates wasted heat, creosote
build-up and pollution.
Second and just as important, is achieving a high level of heat
transfer efficiency. Slowing the rate of flow through the stove or
insert enhances heat transfer, thus allowing more time for heat to
be transferred into your home. To do this, be sure to thoroughly
preheat your stove and then reduce the amount of primary air
by closing the draft control (lower left) to about 1/2 to 3/4 open.
This will decrease the excess oxygen in your flue, which carries
heat up your chimney, but should still be enough air to allow the
stovetoproduceitsmaximumheatoutput. (Moreairmayproduce
a lightly greater amount of heat, but will greatly increase wood
consumption). When the area being heated reaches a comfortable
temperature, slow the burn rate by closing the control to further
improve heat transfer.
Achieving Clean, Long Burns
To achieve long burn times, after having thoroughly preheated
the stove, let the stove top cool down to ꢀ75to 400 degrees (on
Elites, locate thermometer on the face of the insert just above
the door). Now load the firebox and set the draft control. At this
point, you may need to burn the stove with the draft open for a few
minutes to ignite the wood. All Country Collection stoves are EPA
tested for emissions at low burn with the air control completely
closed. Whether or not you should burn your stove with the air
control completely closed will depend on the following factors.
To get the most out of your Country™ Collection stove, you will
need to combine good combustion efficiency with good heat
transfer practices. The following are some tips on how to operate
your stove to achieve the highest overall efficiency.
* How you load your wood
* Your chimney type, height and draft
* Your wood type and its moisture content
* The temperature of the stove
* Which model stove or insert you have
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Experiment with different loading configurations to achieve
longer burns. Try loading the wood from side to side and nesting
itintheashestopreventairflowunderandaroundthewood. Fresh
wood should be loaded to the back of the firebox or to the sides.
Hotcoalsorhalfburnedwoodshouldbebroughttowardsthefront
of the firebox. The way you load your wood can seriously affect
burn times. If the new load does not ignite within a few minutes,
try crisscrossing the load to allow more airflow around the fire,
or try a slightly hotter stove temperature.
Maintenance
DOOR HINGES: If door hinges need lubricating, use an anti-seize
compound (never use oil) available from your Lennox Hearth
Products dealer.
DOORLATCH: Ifyourdoorlatchfailstolatchtightlyandthegasket
is in good condition, place a length of pipe (cheater bar) over the
insideportionofthedoorhandleandbendslightlytowardthedoor
untiltheproperadjustmentisobtained. Ifthedoorhandledoesnot
close easily, apply high temperature anti-seize to the striker.
Determining the lowest setting for efficient low burns. This
will require some experimentation on your part. Try closing the
air control all the way with the stove temperature at 325 to 350
degrees. If the flames are completely extinguished, open the air
control halfway and then slowly close it until there is only a small
amount of flame. It is important to check the stove about 20
minutes after setting the draft control as it takes this long for the
stove temperature to stabilize. There should still be some small
flames on or above the wood load.
DOOR GASKET: Periodically check gasket to make sure it is not
over-compressed. If compressed, replace with a special woven
Door Rope. (Don’t try substituting rope, only use special Lennox
Hearth Products Door Rope).
GOLD OR NICKEL PLATED DOOR: Clean only with household
type glass cleaner and a very soft cotton cloth. Other products
may damage brass, paint and gaskets.
Use ꢁꢀ5 degrees as a starting point. You can try starting tem-
peratures 25 degrees higher or lower to achieve desired burn
times, start 25 degrees lower if the stove burns the wood too
quickly or 25 degrees higher if there are no flames in the firebox
for more than a few minutes after loading the wood. You may or
may not need to burn the stove with the air control open for a few
minutes prior to setting the draft for a low burn, this will depend
on the factors mentioned above. Be sure not to smolder a fire
overnight. Check your chimney for large amounts of smoke as
this indicates very poor combustion.
INSULATING BLANKETS: Your insulating blanket should be in-
spectedduringeverychimneycleaning.Iftheblanketiscompressed
or heavily stained, it should be replaced. Heavy creosote stains or
matting is an indication of improper use and your burning habits
should be reviewed.
GLASS CLEANING: Only clean glass with products specifically
madetouseonwoodstoves.Otherproductscoulddamagegaskets
and paint. Never scrape glass with a razor blade. This can pit the
glass and make it impossible to clean in the future.
It is important to realize that stove technology has changed.
Stoves have changed a great deal in the last few years. This has
led to substantial changes in the methods of operation in new
stoves as compared to older stoves. In old stoves without full
brick linings and ceramic insulation, the rule was “get the stove
as hot as possible before setting the draft on low for overnight
burns.” On newer, high technology Country™ Collection stoves,
thisisnotnecessary. Althoughitisstillimportanttohavethestove
hot enough to burn efficiently, it will require less preheating. Once
you have determined your optimum operating temperatures for
variousburnrates, webelieveyouwillfindyourstoveanextremely
convenient way to achieve your heating needs.
WINDOW GASKET: The window gasket can be checked by run-
ning the flame of a match near the gasket and around the door.
If the flame is drawn in around the window, the gasket should
be replaced.
DOOR HANDLE: Door handle may become tight as you use the
stove. Free the handle up by using dry graphite supplied with the
stove. The directions are included with the graphite.
WARNING
Inspectandcleanchimneyandconnectorfrequently.
Under certain conditions of use, creosote buildup
may occur rapidly.
Do not reload the stove for long burns when the stainless
secondary tubes or baffle supports are glowing red, or when
the stove is uncomfortably hot to load. This indicates the stove
is too hot to load for a long burn. Also, do not load wood for a
long burn on a deep bed of hot coals. Try stirring the coals a few
minutes before loading the stove for a low burn to allow some of
the unburned coals time to burn.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem
Solution
POOR DRAFT:
Extend chimney in length or have the chimney realigned to the proper size flue. Oversized chimneys nor-
mally have poor drafts. Remember, the stoves’ draft depend solely on the natural draft of the chimney (See
drafting section on Page 4). If your stove is not drafting properly, your chimney is the problem. All stoves
are thoroughly tested to ensure proper draft with the correct size chimney flue.
EXCESSIVE DRAFT:
DIRTY GLASS:
With better chimneys being more common, excessive draft can be an issue. Alleviate excessive draft by
slowing the burn rate of the stove once it has reached proper operating temperature (See Maximizing Your
Stoves Overall Efficiency on Page 16).
1) Burn smaller, hotter fires and check to make sure you are not setting the draft down too far with the draft
control.
2) Make sure your wood is well-seasoned and dry (not open to rain - see Creosote and Fuel sections on
Page 3).
3) See Poor Draft section (above) and Cleaning Glass on Page 15 .
SMOKES WHEN
DOOR IS OPEN:
1) If smoke is entering the room, check to make sure your baffle bricks are properly installed
and that the insulating blanket is pushed back flush with the front of the baffle brick.
2) Check the chimney for blockage due to creosote (see Chimney and Creosote sections on Pages 3 and 4).
3) Check draft (See POOR DRAFT section above).
WOOD BURNS
TOO FAST:
1) The draft control must be closed further.
2) Add fuel at lower firebox temperatures.
3) Load wood side to side and reduce the flow of air under wood.
4) The door seal may need replacing, check for leakage.
5) See “Excessive Draft.”
POOR HEAT
OUTPUT:
1) Check your wood. Wet, moist, unseasoned wood will not produce heat.
2) Your stove needs to be seasoned (moisture removed from the steel and brick). Continue to burn a fire.
It normally takes from one to three weeks of burning to season your stove (See Burn-In Procedures on
Page 5).
3) See Excessive Draft section above.
PAINT GIVES OFF
ODOR (smoke):
Paint is tempering-in. Burn only moderately hot for the first few days until paint is fully cured.
Then burn a very hot fire to cure any paint that may not easily cure. Open windows or door to ventilate (See
Burn-In Procedures on Page 5).
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Do’s and Don’ts
DO NOT: Install or operate this stove before reading this manual.
DO NOT: Close the draft beyond the point at which the flames are completely extinguished.
DO NOT: Open the stove door without fully opening the draft first.
DO NOT: Burn driftwood or wood that has been in salt water. This includes some mill ends and scrap lumber that has been floated in
salt water on the way to the mill. (This will void your warranty).
DO NOT: Handle the Nickel or Gold faceplate unnecessarily. Use the door handle only.
DO NOT: Force oversized logs into the firebox as this may dislodge the baffle assembly.
DO NOT: Close the door tightly during Burn-In Period.
DO:
Be sure to clean any fingerprints from the Gold or Nickel faceplate before burning the stove. Clean the Gold or Nickel door
only with a household type glass cleaner and a very soft cloth.
DO:
DO:
Consult local building department if other than recommended clearances are desired.
Read instructions for the brick baffles occasionally to ensure you have not bumped or moved them out of place when loading
wood.
DO:
DO:
DO:
DO:
DO:
Check the chimney and baffle a minimum of every 3 months to make sure they are clean.
Burn seasoned, dry wood only! (RAIN = WET WOOD)
Complete and return your warranty card.
Open the door frequently during Burn-In Period to keep gasket from adhering to the curing paint.
Enjoy the warm feeling of your new Country™ Collection stove.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
GLASS / ARCH
Description
Replacement Parts - Model S160
Cat. No.
7107ꢀ
7107ꢁ
71069
71070
71071
Contact an Authorized Lennox Hearth Products dealer to obtain
any of these parts. Never use substitute materials. Use of
non-approved parts can result in poor performance and safety
hazards.
Arch / Plain
Arch / Sailboat
Arch / Cattail
Arch / Evergreen
Arch / Floral
BLOWER PARTS
Cat. No.
H5658
H5657
H5660
H5656
Description
LEG PARTS
Fan Blade (FSB700)
Fan Cage (FSB700)
7000ꢁ
70000
70001
H56ꢀ1
70007
70008
H5649
Single Black Cascade Steel Legs (4 per pkg.)
Single Black Olympic Cast Legs (4 per pkg.)
Single Gold Olympic Cast Legs (4 per pkg.)
Single Nickel Olympic Cast Legs (4 per pkg.)
Single Brushed Gold Olympic Cast Legs (4 per pkg.)
Single Brushed Nickel Olympic Cast Legs (4 per pkg.)
Heat Shield / Leg Hardware Bolt Kit
Blower Power Cord (FSB700)
Speed Control (FSB700)
BRICKS, BLANKET AND GASKETS
H564ꢀ
H5576
Hꢁ095
H5614
H5607
H5597
H561ꢀ
H5604
H5598
H5610
H5609
Firebrick (replacement - specify size)
Firebrick Letter A - 4-1/4” x 9” (ꢁ per stove)
Firebrick Letter B - ꢀ-1/4” x 8-7/8” (1 per stove)
Firebrick Letter C - ꢁ-1/ꢀ” x 9” (1 per stove)
Firebrick Letter D - 1-ꢁ/4” x 9” (4 per stove)
Firebrick Letter E - 1-1/ꢀ” x 8-7/8” (1 per stove)
Firebrick Letter F - 4-1/ꢀ” x 9” (9 per stove)
Firebrick Letter G - 1-1/ꢀ” x 9” (1 per stove)
Firebrick Letter H - ꢁ-1/ꢀ” x 8-7/8” (1 per stove)
Complete Baffle Brick Set
METAL COMPONENTS
H5579
H5578
H56ꢀ9
H56ꢀ8
H56ꢀ6
H5577
Hꢁ10ꢁ
Door Back and Handle (for Trad door) (door gasket included)
Door Back and Handle (for Arch door) (door gasket included)
Upper Hinge Pin
Lower Hinge Pin
Upper Hinge Pin E-Clip
Set of 6 screws and 6 washers for door assembly
Complete Cut Brick Set
Complete Stainless Secondary Burn Setup
(includes tubes and all mounting hardware)
(Only need 4-1/ꢀ” x 9” bricks to finish)
H5608
H5641
H5640
H56ꢁ9
Complete Brick Set
Hꢁ104
Hꢁ105
H56ꢀ7
Front Stainless Secondary Burn Tube with Support Baffle
Middle & Rear Stainless Secondary Burn Tube with Support
Removable Inner Flue Collar Ring
NAMEPLATES
Ceramic Blanket (ꢀ0” x 11” x 1/ꢀ”)
Glass Gasket 5 feet needed (per foot)
Door Rope 7/8” 5 feet needed (per foot)
FACEPLATES / TRADITIONAL
Traditional / Black
H557ꢁ
H557ꢀ
H564ꢁ
Gold w/ Rivets
71057
71058
71059
71148
71145
Nickel w/ Rivets
Traditional / Gold
Rivets for Nameplates (ꢀ per)
Traditional / Nickel
OUTSIDE AIR KIT REPLACEMENT PARTS - LEG
Traditional / Brushed Gold
Traditional / Brushed Nickel
FACEPLATES
0-0ꢁ00-0ꢁꢁ0-0015 , 15” of 4’ Aluminum Flex Tubing (per
foot - 1.ꢀ5’ needed)”
H566ꢀ
Leg Kit Plenum Box
OUTSIDE AIR KIT REPLACEMENT PARTS - PEDESTAL
15” of 4’ Aluminum Flex Tubing (per foot - 1.ꢀ5’ needed)
6” x 6-1/ꢀ” Rodent Screen
71060
71061
7106ꢀ
71147
71144
Arch / Black
H5516
H5565
H5514
Arch / Gold
Arch / Nickel
Rear Block Off Plate w/ Hole
PEDESTAL PARTS
Arch / Brushed Gold
Arch / Brushed Nickel
GLASS / TRADITIONAL
Traditional / Plain
H5557
H5661
H5564
H558ꢀ
Ash Drawer for Pedestal Small
Cast Iron Ash Plug
71067
71068
7106ꢁ
71065
71066
Ash Plug Remover and Rake
1/ꢀ Cut Brick for Ash Removal
MISC. PARTS
Traditional / Sailboat
Traditional / Cattail
Traditional / Evergreen
Traditional / Floral
H5650
7105ꢀ
H56ꢁꢁ
Draft Rod Knob
Dry Graphite (Apply to door handle and door hinges)
Anti-Seize ꢀ gram pouch
HANDLES
H5654
H565ꢁ
Spring Handle / Nickel
Spring Handle / Gold
ꢀ0
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories
Model S160
PEDESTALS (REQUIRED)
Description
Cat. No.
71108
Pedestal
71109
Ash Drawer Pedestal
or LEGS (Required)
70000
70001
7000ꢀ
70007
70008
7000ꢁ
Olympic Sculptured Black
Olympic Sculptured Gold
Olympic Sculptured Nickel
Olympic Sculptured Brushed Gold
Olympic Sculptured Brushed Nickel
Cascade Steel Black
HEAT SHIELD (REQUIRED WITH LEGS)
Heat Shield
71110
FACEPLATE KITS (INCLUDES FACEPLATE, HANDLE AND NAMEPLATE)
71151
71150
Traditional / Brushed Nickel
Arch / Brushed Nickel
BLOWER
71000
Blower (FSB700)
OUTSIDE AIR KITS
Outside Air Kit / Leg
Outside Air Kit / Pedestal
DECO TRIM
71111
7111ꢀ
7105ꢁ
71054
Paint Gold (1/ꢀ pint)
Paint Nickel (1/ꢀ pint)
MISC.
H5ꢁ08
70K99
Leg Fastening L-Brackets (4 included) (Tie down kit to
be used in mobile or modular homes)
Touch-Up Paint, Metallic Black
ꢀ1
Download from Www.Somanuals.com. All Manuals Search And Download.
Normally, all parts should be ordered through your Lennox distributor or
dealer. Parts will be shipped at prevailing prices at time of order.
WARRANTY
Your wood appliance is covered by a limited warranty (provided with the
appliance). Please read the warranty to be familiar with its coverage.
When ordering repair parts, always give the following information:
1. The model number of the appliance.
ꢀ. The serial number of the appliance.
ꢁ. The catalog number.
Retain this manual. File it with your other documents for future refer-
ence.
4. The description of the part.
5. The quantity required.
PRODUCT REFERENCE INFORMATION
6. The installation date of the appliance.
We recommend that you record the following important information
aboutyourappliance. PleasecontactyourLennoxHearthProductsdealer
for any questions or concerns. For the number of your nearest Lennox
Hearth Products dealer, please call 1-800-9-LENNOX.
If you encounter any problems or have any questions concerning the
installation or application of this system, please contact your dealer.
LENNOX HEARTH PRODUCTS
1110 West Taft Avenue
Orange, CA 9ꢀ865
REPLACEMENT PARTS
See Page 20 for a complete replacement parts list. Use only parts sup-
plied from the manufacturer.
Your Appliance’s Model Number _______________________________________
Your Appliance’s Serial Number________________________________________
The Date On Which Your Appliance Was Installed __________________________
Your Dealer's Name _________________________________________________
Lennox Hearth Products reserves the right to make changes at any time, without notice, in
design, materials, specifications, prices and also to discontinue colors, styles and products.
Consult your local distributor for fireplace code information.
Printed in U.S.A. © 2007 by Lennox Hearth Products
P/N 775,ꢀ14M REV. C 05/ꢀ008
1110 West Taft Avenue • Orange, CA 9ꢀ865
ꢀꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
|