Liebherr Beverage Dispenser EWTN User Manual

41  
64  
0
Up  
Down  
On/Off  
SuperFrost  
Alarm  
On/Off  
Light  
Zone  
Up  
Down  
Installation  
Instructions  
For wine cooler with  
NoFrost freezer compartment and  
Side-By-Side Units  
with IceMaker  
Instructions  
de montage  
Armoire de mise en température des  
vins avec congélateur NoFrost et les  
appareils côte à côte  
avec IceMaker  
2
-
-
6
4
8
6
-12  
4
Instrucciones  
de instalación  
2
4
6
-
-
6
8
-12  
3
Armario de acondicionamiento de  
vinos con congelador NoFrost y  
unidades lado a lado  
2
4
6
-
-
6
8
-12  
2
con IceMaker  
2
4
6
-
-
6
8
-12  
1
WFI1051 / EWTN/ 2956  
7082 408-00  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IMPORTANT  
TO THE INSTALLER  
It is very important that the guidelines and  
instructions are followed in the manual to ensure  
proper installation and operation of the unit. The  
Installation Guidelines section contains important  
information for making sure the installation is cor-  
rect. Read and understand all the information in  
Installation Guidelines, and in this manual before  
the unit is installed.  
A delight in freshness  
WFI1051 / EWTN 2956  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
TABLE OF CONTENTS  
Contents  
Page  
Installation Guidelines................................................................................. 3  
Area Requirements............................................................................... 3  
Electrical Requirement.......................................................................... 3  
Customer’s Responsibility .................................................................... 3  
Blocking For Safety............................................................................... 3  
Unit Venting........................................................................................... 3  
Planning Information................................................................................... 4  
Cabinet Opening Dimensions............................................................... 4  
Assembling Decorative Panels................................................................... 7  
Integrating Cabinetry................................................................................... 8  
Framed Panels...................................................................................... 8  
Overlay Panels...................................................................................... 9  
Reversing Door Hinges............................................................................. 14  
Door Opening Angle........................................................................... 17  
Installation................................................................................................. 18  
Blocking For Safety................................................................................... 22  
IceMaker.................................................................................................... 23  
Water Connection ............................................................................... 23  
Connection to the Water Supply......................................................... 24  
Side-By-Side Installation........................................................................... 25  
A delight in freshness  
WFI1051 / EWTN 2956  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION GUIDELINES  
Area Requirements  
Verify the following:  
WARNING  
!
ELECTROCUTION HAZARD  
• Floors can support refrigerator’s weight plus  
approximately 1200 pounds (544 kg) of food  
weight.  
Electrical Grounding Required. This appli-  
ance is equipped with a three-prong  
(grounding) polarized plug for your protec-  
tion against possible shock hazards.  
• Finished kitchen floor height has to be level.  
Appliance must be shimmed to the floor level if  
the floor heights are not equal to make sure air  
vents are not obstructed.  
DO NOT remove the round grounding  
prong from the plug.  
DO NOT use a two-prong grounding  
adapter.  
DO NOT use an extension cord to  
connect power to the unit.  
• Remove anything attached to rear or side walls  
that can obstruct refrigerator opening.  
• Cutout dimensions are accurate.  
Customer’s Responsibility  
A 115 Volt, 60 Hz, 15 Amp (20 Amp for side-by-  
side installation) fused electrical supply is required.  
We recommend using a dedicated circuit for this  
appliance to prevent electrical overload. Follow the  
National Electrical Code and local codes and ordi-  
nances when installing the receptacle.  
• Electrical outlet is in correct location.  
Do not install this unit next to any other refrigerator  
or freezer except another Liebherr model. Liebherr  
models are designed to allow side-by-side instal-  
lation. They are equipped with a heating system  
to eliminate condensation when units are installed  
side by side. Installing this unit next to any other  
refrigerator or freezer can cause condensation or  
cause damage to the Liebherr unit.  
Blocking For Safety  
The anti-tip brackets must be installed to prevent  
the unit from tipping after it is installed. Refer to  
Blocking For Safety.  
Electrical Requirement  
Unit Venting  
If codes require a separate grounding circuit to be  
used, have a qualified electrician install the circuit.  
DO NOT restrict the air flow. Air flow must be pro-  
vided for the unit to operate. The factory air vents  
provide 31 square inches (200 cm²) of air flow per  
unit. If you are replacing the factory air vents with  
an overlay, the air flow must be the same or greater  
than the factory air vents.  
WARNING  
!
Do not ground to a gas pipe. Check with  
a qualified electrician if you are not sure  
the appliance is properly grounded. Do not  
have a fuse in the neutral or grounding  
circuit.  
WARNING  
!
ELECTRICAL SHOCK HAZARD  
• Electrically ground refrigerator.  
• Do not use an extension cord.  
• Failure to follow these instructions  
could result in fire or electrical shock.  
A delight in freshness  
WFI1051 / EWTN 2956  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
PLANNING INFORMATION  
Cabinet Opening Dimensions - Figure 1  
Allow units to open a minimum of 90° to prevent  
problems removing drawers. With the door open-  
ing 90°, you may have to move drawers slightly to  
clear the door interior.  
Refer to the minimum door clearances in the Pre-  
Installation Specifications chart.  
• Allow for a minimum 3-3/4" (95 mm) filler, for  
corner installations, so the door can open to 90°.  
If you’re using raised panels, consider using a  
wider filler.  
IMPORTANT  
Refer to the full scale illustrations at the end of  
this section for specifics on door openings and  
filler size alternatives.  
3"  
"
(76mm)  
"
"
Figure 1  
A delight in freshness  
WFI1051 / EWTN 2956  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
PLANNING INFORMATION  
WFI 1051 - Figure 2  
Figure 2  
A delight in freshness  
WFI1051 / EWTN 2956  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
PLANNING INFORMATION  
Side-By-Side WFI 1051 - RBI 1400 - Figure 3  
A delight in freshness  
WFI1051 / EWTN 2956  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLING DECORATIVE PANELS  
Figure 4  
Proceed as shown in the illustration:  
(1) Door change frames  
(2) Decorative panel  
(3) Screws for door change frames  
(4) Handle, depending on model  
(5) M4 x 10 screws for handle  
(6) Filler strip  
Figure 4  
A delight in freshness  
WFI1051 / EWTN 2956  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
INTEGRATING CABINETRY  
IMPORTANT  
Framed Panels - Figure 5  
If you are replacing the factory air vents with  
an overlay, DO NOT restrict the air flow. The air  
flow must be the same or greater than the fac-  
tory air vents of 31 square inches (200 cm²).  
If the thickness of the custom panels is less than  
1/4" (6.4 mm), they must be backed up with a sheet  
of shim material to build the total thickness to 1/4"  
(6.4 mm). If the panel is thicker than 1/4" (6.4 mm),  
an edge must be routed around the panel to  
ensure a proper fit.  
The door handles must be installed before the  
screw covers are installed. If you fail to install  
the handles before the screw covers, you can  
damage the covers. The screw covers are  
taped to the unit doors during shipping. Use  
care when removing covers.  
The door panel weight must not exceed  
25 lb (11,3 kg).  
1/4"  
(6.4 mm)  
22-9/16" (573 mm)  
max. 17-1/2" (445 mm)  
1/4" (6.4 mm)  
Window cutout  
=
=
1/4"  
(6.4 mm)  
1/4" (6.4 mm)  
Figure 5  
A delight in freshness  
WFI1051 / EWTN 2956  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
INTEGRATING CABINETRY  
with three panels, the decorative overlay panel, a  
3/32" (2.5 mm) spacer panel and a 1/4" (6.4 mm)  
backer panel.  
Depending on your cabinet manufacturer, this could  
be one panel routed for different dimensions or,  
more likely, three different panels.  
W
Overlay Panels - single install - Figure 6  
The overlay design line allows decorative panels to  
cover the door trim for a more seamless appear-  
ance that blends with the design of the room. To  
achieve this look, the most common way is to work  
=
1 Overlay Panel  
2 Spacer Panel  
3 Backer Panel  
Approx. 3/4"  
(19.1mm)  
3/32" (2.5mm)  
1/4" (6.4mm)  
=
=
=
Window cutout  
=
W
H - Winecooler H - Freezer  
23-5/16"  
(592 mm)  
1 Overlay  
Panel  
33-5/8"  
(854 mm)  
38"  
(965 mm)  
36-1/4"  
(921 mm)  
31-1/2"  
(800 mm)  
21-3/4"  
(553 mm)  
2 Spacer  
Panel  
=
=
32-37/64"  
(828 mm)  
37-9/32"  
(947 mm)  
3 Backer 22-3/4"  
(576 mm)  
Panel  
max 25-1/2"  
(648 mm)  
max17-1/2"  
(445 mm)  
Window  
cutout  
IMPORTANT  
If you are replacing the factory air vents with an  
overlay, DO NOT restrict the air flow. The air flow  
must be the same or greater than the factory air  
vents of 31 square inches (200 cm²).  
=
=
The door handles must be installed on the  
overlay panels before the screw covers are  
installed. If you fail to install the handles on  
the overlay panels before the screw covers ,  
you can damage the covers. The screw covers  
are taped to the unit doors during shipping.  
Use care when removing covers.  
The door panel weight must not exceed  
25 lb (11,3 kg).  
=
Figure 6  
=
=
A delight in freshness  
WFI1051 / EWTN 2956  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
INTEGRATING CABINETRY  
with three panels, the decorative overlay panel, a  
3/32" (2.5 mm) spacer panel and a 1/4" (6.4 mm)  
backer panel.  
Depending on your cabinet manufacturer, this could  
be one panel routed for different dimensions or,  
more likely, three different panels.  
W
Overlay Panels - side by side install  
The overlay design line allows decorative panels to  
cover the door trim for a more seamless appear-  
ance that blends with the design of the room. To  
achieve this look, the most common way is to work  
=
1 Overlay Panel  
2 Spacer Panel  
3 Backer Panel  
Approx. 3/4"  
(19.1mm)  
3/32" (2.5mm)  
1/4" (6.4mm)  
=
=
=
Window cutout  
=
W
H - Winecooler H - Freezer  
23-5/16"  
(592 mm)  
1 Overlay  
Panel  
33-5/8"  
(854 mm)  
38"  
(965 mm)  
36-1/4"  
(921 mm)  
31-1/2"  
(800 mm)  
21-3/4"  
(553 mm)  
2 Spacer  
Panel  
=
=
32-37/64"  
(828 mm)  
37-9/32"  
(947 mm)  
3 Backer 22-3/4"  
(578 mm)  
Panel  
max 25-1/2"  
(648 mm)  
max17-1/2"  
(445 mm)  
Window  
cutout  
IMPORTANT  
If you are replacing the factory air vents with an  
overlay, DO NOT restrict the air flow. The air flow  
must be the same or greater than the factory air  
vents of 31 square inches (200 cm²).  
=
=
The door handles must be installed on the  
overlay panels before the screw covers are  
installed. If you fail to install the handles on  
the overlay panels before the screw covers ,  
you can damage the covers. The screw covers  
are taped to the unit doors during shipping.  
Use care when removing covers.  
The door panel weight must not exceed  
25 lb (11,3 kg).  
=
3/16"  
(4.7mm)  
A delight in freshness  
WFI1051 / EWTN 2956  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INTEGRATING CABINETRY  
A
Figure 7  
C
The factory setting for the door to swing open is  
130°. Use this illustration to ensure other cabi-  
nets or counters do not interfere with the door  
opening.  
Frameless cabinets: The casing trim overlaps  
the cabinets at the side and top. Cabinets may  
require filler strips to prevent interference with  
the cabinet door swing. The door opening must  
allow for filler strips.  
1"  
(25.4 mm)  
2"  
3"  
(50.8 mm )  
(76.2 mm)  
3/4"  
(19.1 mm)  
1/2"  
(12.7 mm)  
1/4"  
1-3/4"  
(44.5 mm)  
2-3/4"  
(69.9 mm)  
2-1/2"  
(63.5 mm)  
2-1/4"  
(57.2 mm)  
1-1/2"  
(38.1 mm)  
1-1/4"  
(31.8 mm)  
(6.4 mm)  
1/4"  
(6.4 mm)  
1/2"  
(12.7 mm)  
3/4"  
(19.1 mm)  
1"  
(25.4 mm)  
3/32"  
(2.4 mm)  
D
1"  
3/4"  
1/2"  
1/4"  
(25.4 mm) (19.1 mm) (12.7 mm) (6.4 mm)  
Figure 7  
A delight in freshness  
WFI1051 / EWTN 2956  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INTEGRATING CABINETRY  
Figure 8  
The optional setting for the door to swing open is  
90°. Use this illustration to ensure other cabinets or  
counters do not interfere with the door opening.  
Frameless cabinets: The casing trim overlaps the  
cabinets at the side and top. Cabinets may require  
filler strips to prevent interference with the cabinet  
door swing. The door opening must allow for filler  
strips.  
A delight in freshness  
WFI1051 / EWTN 2956  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INTEGRATING CABINETRY  
A
C
1"  
3"  
2"  
(50.8 mm )  
1-3/4"  
(44.5 mm)  
1-1/2"  
(38.1 mm)  
1-1/4"  
(31.8 mm)  
(25.4 mm)  
3/4"  
(76.2 mm)  
(19.1 mm)  
2-3/4"  
(69.9 mm)  
2-1/2"  
(63.5 mm)  
2-1/4"  
1/2"  
(12.7 mm)  
1/4"  
(6.4 mm)  
(57.2 mm)  
1/4"  
(6.4 mm)  
1/2"  
(12.7 mm)  
3/4"  
(19.1 mm)  
1"  
24”  
(609.6 mm)  
(25.4 mm)  
3/32”  
(2.4 mm)  
1-1/4"  
(31.8 mm)  
1-1/2"  
48”  
(1219.2 mm)  
(38.1 mm)  
D
1/4"  
(6.4 mm)  
1/2"  
(12.7 mm)  
3/4"  
(19.1 mm)  
1"  
(25.4 mm)  
Figure 8  
A delight in freshness  
WFI1051 / EWTN 2956  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REVERSING DOOR HINGES  
The door hinges can be changed from one side to  
the other if required.  
1. Figure 10: Top: Unscrew the hinge pin (2) and  
remove the screw (5) with the eccentric.  
2. Swivel out the door at the top, ensuring that  
you do not lose the stop (7) and bushing (8); lift  
off the door and place it on the floor.  
8
3. Center: Pull out the hinge pin (9) with its washer.  
4. Swivel out the lower door, lift it out and place it  
on the floor. Take care not to lose the stop (7)  
and washers (8).  
8
5. Unscrew all the door fittings (14, 15, 16, 17).  
6. Figure 11: Unscrew all the door change frames  
and exchange them with one another (6 with 8,  
4 with 7 and handle - remove cover 1). Secure  
them in position using the same screws.  
7. Ensure that the door change frames are cor-  
rectly positioned and mitered.  
Figure 10  
WARNING  
!
Make sure the corners of the door change  
frames are positioned correctly. Sharp  
edges will be exposed if they are not  
mitered or positioned correctly.  
Figure 11  
A delight in freshness  
WFI1051 / EWTN 2956  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REVERSING DOOR HINGES  
8. Figure 12: Unscrew the lower hinge (13).  
10. Unscrew the center hinge (10) and cover (11),  
pull them off to the side and after turning  
them 180°, slide them on again on the opposite  
side and secure them.  
- Remove the stop and bushings (7, 8).  
- Transfer hinge pin (2) to the opposite side.  
- Turn the stop (7) 180° and position bush-  
ings (8) as shown in the detailed drawing.  
- Screw on hinge (13) on the new hinge side.  
11. Place the lower door on the hinge pin (2) at the  
bottom.  
9. On the lower door: Reinstall the door fittings  
(14, 15). Pay special attention to the part (14)  
with the stop.  
- Swivel in the door.  
- Pay special attention to the bushing (12) in the  
center hinge (10).  
- Insert hinge pin (9) and add the washer.  
Figure 12  
A delight in freshness  
WFI1051 / EWTN 2956  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REVERSING DOOR HINGES  
12. Figure 13: Lift up cover (3) on handle side,  
push outward; lift up cover (1) on hinge side  
and pull off.  
13. Unscrew mounting plate (21): first mounting  
screw (20), then inner retaining screw (25).  
- Unscrew hinge (4): first remove the mount-  
ing screw (20), then retaining screws (25). Fit  
hinge (4) to opposite side: for easy assem-  
bly, fit hinge from above and first tighten  
with the upper retaining screw (25) M5, then  
14. Remove the eccentric (5) with the retaining  
screw in the hinge (4).  
15. On the upper door: Reinstall the door fittings  
(16, 17). Pay special attention to the fitting (17)  
with the stop.  
16. Place the upper door on the center hinge, fit the  
bushing (8), stop (7) and washer on the door,  
swivel in the door at the top and insert and  
secure the hinge pin (2) from above through the  
hinge and stop.  
screw (25) and finally mounting screw M4 (20). 17. Re-insert the eccentric (5) with the retaining  
- Turn mounting plate (21) 180° and screw tight  
again on the new handle side: first retaining  
screw (25), then mounting screw (20).  
screw as shown in the detailed drawing.  
Check for proper alignment of all doors. Adjust  
them if necessary using the slots on the hinge.  
21  
4
20 25  
20  
25  
21  
4
12  
14  
15  
17  
16  
15  
Figure 13  
A delight in freshness  
WFI1051 / EWTN 2956  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REVERSING DOOR HINGES  
Door Opening Angle - Figures 14, 15  
The appliance is delivered with a door opening  
angle of 130°.  
If the angle is to be decreased to 90°, proceed as  
follows:  
Insert attached screw (6) in the upper hinge as  
shown in Figure 14.  
Insert attached screw (6) in the lower hinge as  
shown in Figure 15.  
Figure 14  
Figure 15  
A delight in freshness  
WFI1051 / EWTN 2956  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION  
Only install the winecooler/freezer in a stable kitch-  
en cabinet that has been properly aligned.  
- Mount and fix the handles, depending on your  
model and choice.  
Unpacking  
Unpack the installation kit and check with the pro-  
vided parts list if all parts are included.  
The part numbers given in the parts list are identical  
to the numbers in the respective figures.  
For installation you will need the following tools:  
Included:  
- Star Key Torx® 15  
- Star Key Torx® 20  
- Star Key Torx® 25  
- Socket Wrench 8 mm  
- Open-end Wrench 10 mm  
Not in package:  
- Phillips (star) screwdriver  
- Level  
- Ruler  
Figure 16: Installation with Ventilation Grille Set:  
1. Screw the installation frame at the top (1) onto  
the appliance with screws (2).  
2. Place the ventilation grille (3) on this, align it in  
the center and secure at the front from under-  
neath.  
3. Slide brackets (4) onto the side installation  
frames (5) from above and below.  
4. Using the frame (5), screw the brackets onto  
the side wall*.  
5. Slide the side installation frames (5) upwards  
until they are in contact with the underside of  
the ventilation grille.  
6. Secure the side frames with the adhesive sec-  
tion (7) to prevent them from sliding down.  
Remove the protective film and affix the adhe-  
sive sections over the upper brackets on the  
handle and hinge sides.  
Figure 16  
* Depending on model and options  
A delight in freshness  
18  
WFI1051 / EWTN 2956  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION  
- Figure 17: Connect the appliance to the  
main power supply.  
- If the appliance is equipped with an  
IceMaker, establish the connection for  
the water supply. See “IceMaker, Water  
Connection”.  
1. Carefully slide the appliance into the cabinet  
until the ventilation grille touches the surround-  
ing kitchen cabinet.  
2. Align the appliance until it is parallel with the  
surrounding kitchen cabinet. Use the open-  
end wrench 10 mm (3) to adjust the feet at the  
front. Turn clockwise for up and counterclock-  
wise for down. For the rear use the adjusting  
1
2
1
2
3
2
3
8 spanner  
2
3
10 spanner  
Figure 17  
bolt (2). Turn clockwise for down and counter-  
clockwise for up.  
Maximum adjustment: 19/64" (15 mm).  
3. Figure 18: Align the appliance at the side with the  
cabinet side panel and attach it with screws (1).  
- Cover the screws with cover caps (2).  
4. Fit the ventilation grille at the bottom [(3) if the  
door is hinged on the left, (4) if it is on the right]:  
Secure the ventilation grille so that it touches  
the floor and then adjust it using the slots.  
Figure 18  
A delight in freshness  
WFI1051 / EWTN 2956  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION  
At least 31 square inches (200cm2)  
The following ventilation cross-section  
and distances must be observed:  
- There must be a ventilation space of  
at least 31 square inches (200 cm²)  
per appliance in the cabinet plinth  
and under the cabinet top panel.  
- The depth of the ventilation duct at  
the rear of the cabinet must be at  
least 1-1/2" (38 mm).  
1
Alternatively:  
1. For built-in appliances without ven-  
tilation grilles and only with an instal-  
lation frame, ventilation must take place  
through the ventilation duct at the rear  
of the cabinet.  
2
1
Built-in appliances with an installation  
frame:  
Figure 19:  
- Screw the complete installation  
frame (2) to the appliance.  
Figure 19  
2. Built-in appliances with a wooden  
ventilation grille:  
Figure 20: Cut out the wooden trim  
for use as a ventilation grille using the  
enclosed template.  
- The required ventilation cross-sec-  
tion must be at least 31 square  
inches (200 cm²) when a single  
appliance is installed, which cor-  
responds to template “small” (If you  
install two appliances side-by-side,  
the cross-section must be at least  
62 square inches, (400 cm²), which  
corresponds to template “double-  
size;” for more information see “Side-  
by-Side Installation”).  
Remove the attachment bracket (2)  
from the installation frame and screw it  
to the appliance (1) from underneath.  
Place the wooden ventilation grille (5)  
on the appliance, align it in the center  
and secure it from the rear using the  
attachment bracket (2).  
2
1/2"  
5
(13 mm)  
1
24"  
(609,6 mm)  
3-11/16"  
(93,7 mm)  
Figure 20  
A delight in freshness  
WFI1051 / EWTN 2956  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTES  
A delight in freshness  
WFI1051 / EWTN 2956  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BLOCKING FOR SAFETY  
Figure 21: Secure the appliance in place so it does  
IMPORTANT  
not tip forward when the fully stocked door is  
opened.  
The anti-tip brackets can be installed in either  
direction or closer together. Always position  
the anti-tip brackets as wide apart as pos-  
sible, but make sure they are anchored to two  
studs.  
2. Measure the distance from the floor to the  
upper edge of the unit.  
3. Locate and mark two wall studs (1) against the  
wall where the refrigerator will be located. The  
space between the unit top and the bottom of  
the brackets must not be more than  
1/4" (6.4 mm).  
6. Using the adjustable roller base, raise the unit  
until it makes contact with the brackets. Make  
sure the front levelers are firmly on the floor to  
prevent appliance from tipping forward.  
4. Make sure the screws (2) extend a minimum of  
IMPORTANT  
1" (25.4 mm) into each of the wall studs.  
If your unit is positioned in between the  
wall studs, a board can be secured to the  
wall. Make sure the board is secured to the  
studs with screws that will penetrate into the  
studs a minimum of 1" (25.4 mm). The board  
should be a minimum of 1" x 6" (25.4 mm x  
152.4 mm) and long enough to secure both  
ends to the wall studs.  
5. Make sure the anti-tip brackets (3) extend  
at least 3" (76.2 mm) over the unit and are  
securely in place.  
3
1
2
min 3"  
Figure 21  
A delight in freshness  
WFI1051 / EWTN 2956  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ICEMAKER  
Water Connection - Figure 22  
Please read the first three points of the safety  
instructions and warnings before connecting the  
appliance to the main water supply.  
• The water pressure must be between 21.8-  
87.0 psi (1.5-6 bar).  
• Use a 1/4" OD copper line to connect the water  
supply to the solenoid valve. This is not sup-  
plied with the appliance (Figure 22).  
• A shut-off valve, such as the saddle valve illus-  
tration here, must be installed between the hose  
line and the main water supply so the water sup-  
ply can be stopped if necessary.  
Figure 22  
Do not install the shut-off valve behind the  
appliance.  
• If you have hard water, we recommend you install  
a water softener. Also, a filter must be installed if  
the water contains solids such as sand.  
• All equipment and devices used to supply the  
water to the appliance must comply with the cur-  
rent regulations for your geographical area.  
A delight in freshness  
23  
WFI1051 / EWTN 2956  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ICEMAKER  
3. Open the shut-off valve for the water supply  
and check the entire water system for leaks.  
Before the appliance is used for the first time a  
licensed plumber should bleed air from the sys-  
tem.  
Connection to the Water Supply  
1. Install the shut-off valve, water filter and auto-  
matic shut-off device as required.  
Note  
The solenoid valve is located at the rear of  
your unit.  
4. Insert the electrical plug for the combined appli-  
ance into the electrical outlet (Figure 23).  
2. Place a 1/4" OD copper tubing between the  
shut-off valve and solenoid valve. Make sure  
there is approximately 30" (70 cm) of excess  
tubing behind the unit for easy connection.  
5. Move the appliance into final position in the  
room.  
IMPORTANT  
The solenoid valve has a Metric R3/4 male  
connection.  
A R3/4(metric) to a 1/4" OD adapter and  
cable clip are supplied with the icemaker.  
Figure 24: Remove the cover cap (4) from  
the solenoid valve (1). Install the connection  
bracket (2) with sealing ring (6) on the solenoid  
valve (1). Attach the copper tube to the connec-  
tion bracket (2). Secure the copper tube (3) to  
the appliance using the cable clip (5).  
Figure 23  
A delight in freshness  
24  
WFI1051 / EWTN 2956  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SIDE-BY-SIDE INSTALLATION  
1
4
1
6
2
3
5
5
Figure 24  
A delight in freshness  
WFI1051 / EWTN 2956  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SIDE-BY-SIDE INSTALLATION  
Unpacking  
Figure 25: To install the WFI 1051 appliances side-  
by-side, proceed as follows:  
Unpack the side by side installation kit and check  
with the provided parts list if all parts are included.  
The part numbers given in the parts list are identical  
to the numbers in the respective figures.  
- Always place the WF/WFI 1051 with the hinges  
on the left-hand side (looking from the front).  
Installation with SBS Ventilation Grille Set:  
For installation you will need the following tools:  
1. Affix the spacer (1) on the side wall of the appli-  
ance – remove the protective film.  
Included:  
- Star Key Torx® 15  
- Star Key Torx® 20  
- Star Key Torx® 25  
- Socket Wrench 8 mm  
- Open-end Wrench 10 mm  
2. Push the appliances together,  
- align them parallel to each other.  
3. Use a level on the top to align them to the  
same height:  
4. Use the open-end wrench 10 mm (3) to adjust  
the feet at the front of the roller base. Turn  
clockwise for up and counterclockwise for down.  
For the rear, turn the adjusting bolt (2) clock-  
wise down and counterclockwise up.  
Not in package:  
- Phillips (star) screwdriver  
- Level  
- Ruler  
4
Figure 25  
A delight in freshness  
WFI1051 / EWTN 2956  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SIDE-BY-SIDE INSTALLATION  
5. Figure 26: Secure the installation frame (3)  
5
2
3
at the top to the appliances with screws (2).  
- Align the appliance at the front bottom.  
- Use the predrilled holes to align the  
installation frame (2).  
- First mount the installation (3) frame with  
4 screws (2) to one appliance, then align  
the other appliance with the predrilled  
holes to the installation frame (3) and  
secure it with the screws (2).  
6. Figure 26: Position the attachment brack-  
ets (6) at the rear of the appliances at the  
top and bottom. Slide the upper attachment  
bracket upwards as far as possible. Secure it  
at the side using the screws provided (5). Do  
not overtighten!  
6
6
5
6
5
6
81-/4"  
c.a(210)  
Figure 26  
A delight in freshness  
27  
WFI1051 / EWTN 2956  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SIDE-BY-SIDE INSTALLATION  
7. Figure 27: Push the long carriage bolt  
M5x260 (7) through the leveling wheels as shown.  
Fit in a washer (8). Screw on the wing nut (9) and  
tighten it manually. Do not overtighten.  
8. Turn the adjustable roller base up. Otherwise  
you will damage the floor when you push in the  
appliances.  
9. Secure the ventilation grille (10) to the appli-  
ance with screws (11). Push in the sealing  
strip (4) as shown.  
10  
9
4
11  
9
8
7
7
7
8
8 spanner  
2
4
3
10 spanner  
Figure 27  
A delight in freshness  
WFI1051 / EWTN 2956  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SIDE-BY-SIDE INSTALLATION  
10. Figures 28, 29: Slide the side installation  
10  
frames (15) upward until they are in con-  
tact with the underside of the ventilation  
grille, Figure 28.  
11. Secure the side frames with the adhe-  
sive section (17) to prevent them from  
sliding down. Remove the protective film  
and place the adhesive sections over the  
upper brackets.  
17  
11  
12. Install anti-tip brackets for each appliance.  
Refer to “Blocking For Safety.”  
17  
15  
15  
11  
17  
Figure 28  
min 3"  
Figure 29  
A delight in freshness  
WFI1051 / EWTN 2956  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SIDE-BY-SIDE INSTALLATION  
13. Figure 30, 31: Connect the appliances:  
- to the main power supply and  
- to the water supply if the appliance is equipped  
with an IceMaker. See “IceMaker, Water  
Connection,Figure 30.  
14. Carefully slide the connected appliances into the  
recess until the ventilation grille touches the top,  
Figure 31.  
15. Align the appliances by using only the outer lev-  
13  
eling wheels at the front (3) and rear (2).  
Figure 30  
8 spanner  
14  
2
3
10 spanner  
15  
Figure 31  
A delight in freshness  
WFI1051 / EWTN 2956  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SIDE-BY-SIDE INSTALLATION  
16. Figure 32: Attach the aligned combination  
to the surrounding kitchen cabinet. Secure it  
through the side frames using the screws (20)  
provided.  
-
Cover the screws with cover caps (21).  
17. Now adjust the center adjustable roller  
bases (22) so that they make slight contact  
with the floor.  
18. Install the lower ventilation grille (23): Secure  
the ventilation grille so that it touches the floor  
and adjust it using the slots. Do not overtighten!  
20  
21  
16  
8 spanner  
2
3
10 spanner  
17  
22  
18  
24  
24  
24  
23  
24  
Figure 32  
A delight in freshness  
WFI1051 / EWTN 2956  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SIDE-BY-SIDE INSTALLATION  
1. For built-in appliances without ventilation  
grilles and only with installation frame (2), ven-  
tilation must take place through the ventilation  
duct at the rear of the cabinet. Ensure that the  
ventilation cross-section is at least 31 square  
inches (200 cm²) per appliance.  
At least 62 square inches (400 cm²) for side-by-  
side installation of two appliances. Built-in appli-  
ances with an installation frame:  
- Figure 33: Screw the installation frame (2) to  
the appliance through the attachment brack-  
ets.  
At least 31 square inches (200cm2)per unit  
1
2
Figure 33  
A delight in freshness  
WFI1051 / EWTN 2956  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SIDE-BY-SIDE INSTALLATION  
Built-in appliances with a wooden ventilation  
- Remove the attachment brackets from the  
installation frame (2) and screw them to the  
appliance from underneath.  
- Place the wooden ventilation grille (5) on the  
appliance, align it in the center and secure it  
from the rear using the attachment brackets.  
grille:  
2. Figure 34: Cut out the wooden trim for use as  
a ventilation grille using the attached template.  
- The required ventilation cross-section must  
be at least 62 square inches (400 cm²) for  
side-by-side installation of two appliances,  
which corresponds to the attached template  
“double-size.”  
2
1/2"  
(13 mm)  
5
48"  
(1219,2 mm)  
3-11/16"  
(93,7 mm)  
X
Figure 34  
A delight in freshness  
WFI1051 / EWTN 2956  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Lanzar Car Audio Car Amplifier VCT 1500D User Manual
LG Electronics Washer DLEX3370 User Manual
Linksys Network Card BEFN2PS4 User Manual
Magnavox Flat Panel Television 26MD255V User Manual
Makita Sander 9045B User Manual
Marantz Flat Panel Television PD5010D User Manual
Marvel Industries Refrigerator 5CAF fmar User Manual
McCulloch Blower MB3200 User Manual
McCulloch Lawn Mower 250 B User Manual
Micro Innovations Network Card USB740R User Manual