WASHING MACHINE
SERVICE MANUAL
!
CAUTION
READ THIS MANUAL CAREFULLY TO DIAGNOSE
PROBLEMS CORRECTLY BEFORE SERVICING THE UNIT.
MODEL : WM2411HW/WM2011H*/WM1811CW
WM2432HW/WM2032H*/WM1832CW
WM0532HW/WD-10210BD/WD-12210(5)BD
WM2444H*M/WM2442H*/WM2042CW
WM0642H*
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
1. SPECIFICATIONS .........................................................................................................................3
2. FEATURES & TECHNICAL EXPLANATION ................................................................................ 5
3. PARTS IDENTIFICATION ............................................................................................................ 7
4. INSTALLATION............................................................................................................................. 8
5. OPERATION ................................................................................................................................11
6. WIRING DIAGRAM / PROGRAM CHART...................................................................................15
7. TROUBLESHOOTING.................................................................................................................19
7-1. BEFORE PERFORMING SERVICE ...................................................................................19
7-2. QC TEST MODE.................................................................................................................19
7-3. HOW TO CHECK THE WATER LEVEL FREQUENCY ......................................................19
7-4. ERROR DISPLAY ...............................................................................................................20
8. ERROR DIAGNOSIS AND CHECK LIST ....................................................................................22
8-1. DIAGNOSIS AND SOLUTION FOR ABNORMAL OPERATION ........................................22
8-2. FAULT DIAGNOSIS AND TROUBLESHOOTING ..............................................................25
9. DISASSEMBLY INSTRUCTIONS ...............................................................................................32
10. EXPLODED VIEW .....................................................................................................................40
10-1. CABINET & CONTROL PANEL ASSEMBLY....................................................................40
10-2. DRUM & TUB ASSEMBLY................................................................................................41
10-3. DISPENSER ASSEMBLY .................................................................................................42
2
Download from Www.Somanuals.com. All Manuals Search And Download.
1. SPECIFICATIONS
WM2411HW
WM2432HW
WM2011HS / WM2011HW
WM2032HS / WM2032HW
WM0532HW / WD-10210BD
WM1811CW
WM1832CW
ITEM
WD-12210(5)BD
POWER SUPPLY
120V ~ 60Hz
PRODUCT WEIGHT
190 lbs. (86 kg)
WASHING
DRAIN MOTOR
WASH HEATER
WASH
280W
235W
ELECTRIC
POWER
80W
CONSUMPTION
1000W
42 rpm
REVOLUTION
SPEED
SPIN
0-1200 rpm
0-1000 rpm
0-900 rpm
CYCLES
9
6
6
7
5
5
5
4
5
WASH / RINSE TEMPERATURES
SPIN SPEEDS
OPTIONS
Prewash, Stain Cycle, Quick Cycle, Extra Rinse, Rinse+Spin, Delay Wash
CUSTOM PROGRAM
WATER CIRCULATION
OPERATIONAL WATER PRESSURE
CONTROL TYPE
Incorporated
Incorporated
-
4.5 145 psi (30-1000 kPa)
Electronic
WASH CAPACITY
3.22 cu.ft (3.72 cu.ft.IEC)
1
-
3
-
4
-
DIMENSIONS
27”(W) X 29 / ”(D) X 42 / ”(H), 49 / ”(D, door open)
2
4
5
DELAY WASH
up to 19 hours
up to 12 hours
up to 9 hours
DOOR SWITCH TYPE
WATER LEVEL
PTC + Solenoid
7 steps (by sensor)
Incorporated
LAUNDRY LOAD SENSING
ERROR DIAGNOSIS
AUTO POWER OFF
CHILD LOCK
Incorporated
Incorporated
Incorporated
RLM ENABLE
3
Download from Www.Somanuals.com. All Manuals Search And Download.
ITEM
WM2444H*M
WM2442H*/WM0642H*
120V ~ 60Hz
WM2042CW
235W
POWER SUPPLY
PRODUCT WEIGHT
190 lbs. (86 kg)
WASHING
280W
ELECTRIC
POWER
DRAIN MOTOR
WASH HEATER
WASH
80W
CONSUMPTION
1000W
42 rpm
REVOLUTION
SPEED
SPIN
0-1200 rpm
0-1000 rpm
CYCLES
7
6
6
5
4
5
WASH / RINSE TEMPERATURES
SPIN SPEEDS
OPTIONS
Prewash, Stain Cycle, Quick Cycle, Extra Rinse, Rinse+Spin, Delay Wash
CUSTOM PROGRAM
WATER CIRCULATION
OPERATIONAL WATER PRESSURE
CONTROL TYPE
Incorporated
Incorporated
-
4.5 145 psi (30-1000 kPa)
Electronic
WASH CAPACITY
3.32 cu.ft (3.83 cu.ft.IEC)
1
-
4
-
DIMENSIONS
27”(W) X 29 / ”(D) X 44”(H), 49 / ”(D, door open)
2
5
DELAY WASH
up to 12 hours
up to 9 hours
DOOR SWITCH TYPE
WATER LEVEL
PTC + Solenoid
10 steps (by sensor)
Incorporated
LAUNDRY LOAD SENSING
ERROR DIAGNOSIS
AUTO POWER OFF
CHILD LOCK
Incorporated
Incorporated
Incorporated
RLM ENABLE
Incorporated
4
Download from Www.Somanuals.com. All Manuals Search And Download.
2. FEATURES & TECHNICAL EXPLANATION
2-1.FEATURES
Direct Drive System
The advanced Brushless DC motor directly drives the drum
without belt and pulley.
Tilted Drum and Extra Large Door Opening
The tilted drum and extra large door opening make it possible
to load and unload easily.
Water Circulation
Spray detergent solution and water onto the load repeatedly.
Clothes are soaked more quickly and thoroughly during the wash cycle.
Detergent suds are eliminated more easily by the water shower
during rinse cycle. The water circulation system uses both
water and detergent more efficiently.
RollerJ ets
The washing ball enhances wash performance and reduces
damage to clothing. The jets spray and help tumble clothes to enhance
washing performance while maintaining fabric care.
Built-in Heater
The internal heater automatically heats the water to the optimum
temperature on selected cycles.
Child Lock
The Child lock feature prevents children from pressing any buttons
to change the settings during operation.
Using the RLM (Remote Laundry Monitor)
The RLM monitors status of your washer and/or dryer. You can plug the
display unit into any power outlet in your home.
The RLM Display Unit can be purchased separately for this washer.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
2-2.FUZZY LOGIC WASHING TIME OPTIMIZATION
To get the best washing performance, optimal time is determined by the water temperature,
the selected washing temperature, and the size of the load.
water
temperature
washing time
the best
washing
performance
selected
FUZZY
LOGIC
washing
rinsing time
temperature
spin rhythm, time
load
size
SENSING
PROCESSING
DETERMINATION
EFFECT
2-3.WATER LEVEL CONTROL
This model incorporates a pressure sensor which can sense the water level in the tub.
The water supply is stopped when the water level reaches the preset level, the washing
program then proceeds.
Spinning does not proceed until the water in the tub drains to a certain level.
2-4.DOOR CONTROL
The door can be opened by pulling the door handle whenever washer is not in operation.
When the cycle is completed, the DOOR LOCKED light will turn off.
If a power failure has occurred while in operation, the door will lock for 5 minutes.
Clicking sounds can be heard when the door is locked / unlocked.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
3. PARTS IDENTIFICATION
• If the supply cord is
damaged, it must be
replaced by the
manufacturer or its
authorized service
technician in order to
avoid a hazard.
(PLC Modem)
ACCESSORIES
7
Download from Www.Somanuals.com. All Manuals Search And Download.
4. INSTALLATION
Before servicing, ask the customer what the trouble is.
Check the setup (power supply is 120V AC, remove the transit bolts....).
Check with the troubleshooting guide.
Plan your service method by referring to the disassembly instructions.
Service the unit.
After servicing, operate the appliance to see whether it functions correctly.
STANDARD INSTALLATION
The appliance should be installed as follows:
REMOVE THE TRANSIT
BOLTS
INSTALL THE APPLIANCE
ADJUST THE
LEVELING
ON A FLAT AND FIRM SURFACE
Remove the transit bolts
(4 EA: ) with the supplied wrench.
Turn the leveling feet to adjust
the appliance horizontally.
Keep the transit bolts and
spanner for future use.
Insert the 4 caps
(provided) into the hole.
The appliance goes up by
rotating the feet clockwise.
The appliance come down by
rotating the feet counterclockwise.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO CONNECT THE INLET HOSE
Verify that the rubber washer is inside of the
valve connector.
Connect the inlet hose firmly to prevent leaks.
CONNECT THE DRAIN HOSE
Make sure that the hose is not twisted.
The end of the drain hose should be placed less than 96
CONNECT POWER PLUG
Avoid submerging the end of the hose.
”
from the floor.
Avoid connecting several electric devices, as
doing so may cause a fire.
Connect the power plug to the wall outlet.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
TEST OPERATION
Preparation for
washing.
Press the POWER button.
Press the Start/Pause
button.
Connect the power plug to
the outlet.
Connect the inlet hose.
Listen for clicking sounds to
determine if the door has
locked.
Check the water heating
function.
Check the automatic
reversing rotation of the
drum.
Check the water supply.
Press the WASH / RINSE button
and the present temperature will
be displayed.
Make sure that the drum rotates
clockwise and counterclockwise.
Verify that if water is supplied
through the detergent dispenser.
Check the drain and spin
functions.
Press the
START / PAUSE button.
Water removal
Press the POWER button twice
to restart.
Press the SPIN SPEED button.
Press the START / PAUSE button.
Check the drain and spin
functions.
Listen for clicking sounds to
determine if the door is
unlocking.
If SVC is required, remove the
remaining water in the tub, by
pulling out the drain plug.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
5. OPERATION
• Use this button to turn the power
On / Off.
• Lights whenever the door is locked.
• Choose High / Low
• The door can be unlocked by pressing
the Start / Pause button to stop the
washer.
• Rotate the Cycle selector
knob to select the cycle
designed for different
types of fabric and soil
levels.
•
Allows you to store a customized wash cycle for future use.
• To create a Custom Program :
• Select a water temperature based o
load you are washing.
1) Select a cycle.
2) Select the other desired Wash / Rinse Temp., Spin Speed, Soil Level.
3) Select the desired Options.
4) Press and hold the Custom Program button for 3 seconds (2 beep sounds).
5) Press the Start / Pause button.
• To change the spin speed, select th
Spin Speed button until the desired
displayed.
• To change the soil level, select the S
button until the desired setting is dis
The Custom Program is now stored for future use.
• To reuse the program, select Custom Program and press Start / Pause.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
/ Off.
• These lights show elapsed time of the
selected cycle.
• This display shows :
a) the estimated time remaining in the cycle when
operating.
b) an error code when an error has been detected.
• Use this button to Start /
Stop the washer.
• Use this option to prevent
unwanted use of the washer.
Press and hold Quick Cycle and
Delay Wash button for 3 seconds
to lock / unlock control.
• Prewash
: Use this option for loads that need pretreatment.
It adds 16 minutes prewash and drain.
on the type of
• Stain Cycle : Adds time to the wash and rinse cycles for
better stain removal. Automatically provides a
rinse.
e
setting is
• When Child lock is set, “ ” blinks
and all buttons are disabled but
the Power button. You can
thereby lock the washer while
it is operating.
• Quick Cycle : The Quick cycle offers a quick cycle time.
• Extra Rinse : This option provides an additional rinse cycle.
• Rinse+Spin : Use this option to rinse and then spin.
Soil Level
splayed.
• Delay Wash : Allows the start of any cycle to be delayed for
1~19(12, 9) hours.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
WM2411HW
WM2011HS / WM2011HW
WM1811CW
WM2432HW / WD-12210(5)BD
WM2032HS / WM2032HW / WM0532HW / WD-10210BD
WM1832CW
13
Download from Www.Somanuals.com. All Manuals Search And Download.
WM2444H*M/WM2442H*
WM2042CW
WM0642H*
CONFORTOR
14
Download from Www.Somanuals.com. All Manuals Search And Download.
6. WIRING DIAGRAM / PROGRAM CHART
WM2411HW / WM2011HS / WM2011HW / WM2432HW / WM2032HS / WM2032HW /
WM0532HW / WD-10210BD / WD-12210(5)BD
WM1811CW / WM1832CW
15
Download from Www.Somanuals.com. All Manuals Search And Download.
WM2444H*M
WM2442H*M/WM0642H*
16
Download from Www.Somanuals.com. All Manuals Search And Download.
WM2042CW
17
Download from Www.Somanuals.com. All Manuals Search And Download.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
7. TROUBLESHOOTING
7-1. BEFORE PERFORMING SERVICE
Be careful of electric shock when disconnecting parts for while troubleshooting.
The voltage of each terminal is 120V AC and DC when the unit is plugged in.
7-2. QC TEST MODE.
The washer must be empty and the controls must be in the off state.
¤
Press the SPIN SPEED and SOIL LEVEL buttons simultaneously.
¤Ł
¤Ø
Press the Power button, while the above condition. Then buzzer sound twice.
In order to advance to the next step of test mode, press the START / PAUSE button once.
Number of times the
Start/Pause button is pressed
Check Point
Display Status
None
Turns on all lamps and locks the door.
Tumble clockwise.
1 time
2 times
3 times
4 times
5 times
6 times
7 times
8 times
9 times
10 times
11 times
12 times
13 times
rpm (40~50)
Low speed Spin.
rpm
High speed Spin.
rpm
Inlet valve for prewash turns on.
Inlet valve for main wash turns on.
Inlet valve for hot water turns on.
Inlet valve for softener turns on.
Inlet valve for bleach turns on.
Tumble counterclockwise.
Heater turns on for 3 sec.
Circulation pump turns on.
Drain pump turns on.
Water level frequency (25~65)
Water level frequency (25~65)
Water level frequency (25~65)
Water level frequency (25~65)
Water level frequency (25~65)
rpm (40~50)
Water temperature
Water level frequency (25~65)
Water level frequency (25~65)
Turn off all lamps.
Power off and unlock the door.
WM2411HW
WM2011HS / WM2011HW
WM1811CW
WM1832CW
WM2432HW
WD-12210(5)BD
WM2032HS / WM2032HW
WM0532HW / WD-10210BD
7-3. HOW TO CHECK THE WATER LEVEL FREQUENCY
Press the SPIN SPEED and SOIL LEVEL button simultaneously.
The digits indicate the water level frequency ( x.1 kHz ).
So, for example a display indicating 241 : a Water level frequency of 241 x.1 kHz
= 24.1 kHz
19
Download from Www.Somanuals.com. All Manuals Search And Download.
7-4. ERROR DISPLAY
If you press the START/PAUSE button when an error is displayed, any error excep
disappear and the machine will go into the pause status.
will
In case o
if the error is not resolved within 4 min., power will be turned off automatically and the error code will
blink. But in the case of , power will not be turned off.
if the error is not resolved within 20 sec., or the in case of other errors,
ERROR
SYMPTOM
CAUSE
• Correct water level (2 level) is not reached within 8 minutes
after water is supplied or it does not reach the preset water
level within 25 minutes.
WATER INLET
1
ERROR
• The load is too small.
• The appliance is tilted.
• Laundry is gathered to one side.
• Non distributable things are put into the drum.
IMBALANCE
2
ERROR
DRAIN
3
• Not fully drained within 10 minutes.
ERROR
• Water is overflowing (over 8 level).
OVER FLOW
4
¡ If
is displayed, the drain pump will operate to
ERROR
the drain water automatically.
PRESSURE
5
• The SENSOR SWITCH ASSEMBLY is out of order.
SENSOR
ERROR
• Door not all the way closed.
• Loose electrical connections at Door switch and
PWB Assembly.
• The DOOR SWITCH ASSEMBLY is out of order.
DOOR OPEN
6
ERROR
HEATING
7
• The THERMISTOR is out order.
ERROR
20
Download from Www.Somanuals.com. All Manuals Search And Download.
ERROR
SYMPTOM
CAUSE
OVER
CURRENT
ERROR
•
•
MAIN PWB ASSEMBLY is out of order.
8
Winding in the STATOR ASSEMBLY is short-circuited.
• The connector (3-pin, male, white) in the MOTOR
HARNESS is not connected to the connector
(3-pin, female, white) of STATOR ASSEMBLY.
• The electric contact between the connectors
(3-pin, male, white) in the MOTOR HARNESS
and 4-pin, female, white connector in the MAIN PWB
ASSEMBLY
LOCKED
MOTOR
ERROR
9
is bad or unstable.
• The MOTOR HARNESS between the STATOR
ASSEMBLY and MAIN PWB ASSEMBLY is cut (open
circuited).
• The hall sensor is out of order/defective.
• Loose Ball Sensor Connector.
• Ball Sensor is out of order.
¡ Displayed only when the START / PAUSE button is first
pressed in the QC Test Mode.
BALL SENSOR
ERROR
10
11
12
• EEPROM is out of order.
¡ Displayed only when the START / PAUSE button is first
pressed in the QC Test Mode.
EEPROM
ERROR
POWER
•
The washer experienced a power failure.
FAILURE
21
Download from Www.Somanuals.com. All Manuals Search And Download.
8. ERROR DIAGNOSIS AND CHECK LIST
8-1.DIAGNOSIS AND SOLUTION FOR ABNORMAL OPERATION
SYMPTOM
No power
GUIDE FOR SERVICE CALL
Is the power plug connected firmly to
120V AC outlet?
Power failure? or Breaker opened?
Is the outlet controlled by a switch?
Visit to service.
Water inlet trouble
Is
displayed?
Is the tap opened?
Is the tap frozen?
Is the water supply shut-off?
Clean the filter of
inlet valve
Is filter in the inlet valve clogged with
foreign material?
Visit to service.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMPTOM
Door error
GUIDE FOR SERVICE CALL
Was the load too large?
Visit to service.
Drain trouble
Visit to service.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMPTOM
GUIDE FOR SERVICE CALL
Suds overflow from the
appliance.
Is a low-sudsing detergent used?
(In this condition, wash and
spin do not operate normally)
LOW-SUDSING
Is the proper amount of detergent used
as recommended?
Recommend to reduce the amount
of detergent.
This appliance has an automatic suds sensing function which
prevents overflow.
When excessive suds are sensed, the suds removing
implementations such as drain, water input, pause will operate,
without rotating the drum.
No softening effect
Is softener put in the correct compartment of
the dispenser?
Is the softener cap clogged?
Explain proper use of softener.
Clean the softener compartment
Visit to service.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
8-2.FAULT DIAGNOSIS AND TROUBLESHOOTING
CAUTION
1. Be careful of electric shock if disconnecting parts while troubleshooting.
2. First of all, check the connection of each electrical terminal with the wiring diagram.
3. If you replace the MAIN PWB ASSEMBLY, reinsert the connectors correctly.
NO POWER
Check the fuse or reset
the circuit breaker.
Is the supplied voltage 120V AC?
Replace the FILTER
ASSEMBLY (CIRC).
Is the voltage between the 2 FILTER ASSEMBLY
connectors 120V AC?
Replace MAIN PWB
ASSEMBLY.
Is the LED(1) on?
Are the connectors(2) on the PWB loose?
Reconnect.
Replace the MAIN PWB
ASSEMBLY.
Is wire of the DISPLAY PWB ASSEMBLY
broken?
Replace DISPLAY PWB ASSEMBLY
or repair wire.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
NO WATER SUPPLY
Is water supply shut-off?
NO
Is the tap opened?
Open the tap.
NO
YES
When you press both SPIN SPEED button and
SOIL LEVEL button simultaneously, is the water
level frequency below 246?
Check the AIR CHAMBER
and the tube (clogged).
YES
NO
Is the inlet valve filter clogged?
NO
Clean the filter.
YES
NO
Is resistance between each terminal of INLET
VALVE ASSEMBLY 0.8-1.2kΩ
Replace the INLET VALVE
ASSEMBLY.
?
YES
Verify the voltage of the inlet valve connector is
120V AC.
Check electrical connection.
Replace the MAIN PWB
ASSEMBLY.
NO
(Refer to 7-2 QC TEST MODE)
DETERGENT DOES NOT FLOW IN
Refer to
NO
NO
Is water supplied?
NO WATER SUPPLY
YES
Are receptacles correctly connected to the
terminals of the INLET VALVE ASSEMBLY?
Check the wiring.
YES
Put the detergent in the
correct place.
Has detergent been put in the correct compartment
of the dispenser?
NO
YES
YES
Is the detergent caked or hardened?
Clean the dispenser.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
SOFTENER / BLEACH DOES NOT FLOW IN
Refer to
Is water supplied?
NO WATER SUPPLY
Check the wiring on the
dispenser.
Are the plugs correctly connected to the terminals of
the INLET VALVE ASSEMBLY?
Put it in the correct
compartment.
Is softener / bleach put in the correct compartment of
the drawer?
Clean the Cap and
Container.
Is the softener / bleach cap clogged?
ABNORMAL SOUND
Is the motor bolt loosened?
Secure the bolt.
Replace the STATOR
ASSEMBLY or ROTOR
ASSEMBLY.
Is there friction noise coming from the motor?
27
Download from Www.Somanuals.com. All Manuals Search And Download.
HEATING WITHOUT WATER
When pressing SPIN SPEED and SOIL LEVEL at the
same time after draining, is the water level frequency
255?
When pressing SPIN SPEED and SOIL LEVEL buttons
at the same time while wash, is the water level
frequency between 230 - 243 ?
Replace the
SENSOR SWITCH
ASSEMBLY.
Replace the MAIN PWB
ASSEMBLY.
Check the voltage between two pins while pressing
the POWER button. Is the voltage 120V AC?
DRAIN MALFUNCTIONING
Repair the DRAIN HOSE
ASSEMBLY.
Is the drain hose twisted or frozen?
Is the impeller of the drain pump clogged?
Remove foreign material.
Reconnect or repair the
connector
Is the connector disconnected, disassembled?
Replace the DRAIN
PUMP ASSEMBLY.
Is the coil of the drain pump too high or low?
(resistance of coil is 10-20Ω)
When checking voltage between connectors during
spin, is the voltage 120V AC as in the figure?
Replace the MAIN PWB
ASSEMBLY.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
WASH HEATER TROUBLE
HEATING CONTINUOUSLY ABOVE
THE SETTING WATER TEMPERATURE
Push the THERMISTOR
tightly to the rubber.
When checking the THERMISTOR on the tub,
is the THERMISTOR loose?
29
Download from Www.Somanuals.com. All Manuals Search And Download.
WILL NOT CIRCULATE WATER
Is the impeller of the drain pump clogged?
Remove foreign material.
Remove foreign material.
Are the Hose Connector and/or Hose clogged?
Is the connector disconnected, disassembled?
Reconnect or repair
the connector.
Is the coil of the right side of drain pump open
or short circuited? (Coil R is 18-30Ω)
Replace PUMP MOTOR
ASSEMBLY.
When checking voltage between the
connectors during spin, is the voltage 120V AC,
as the figure?
Replace the MAIN PWB
ASSEMBLY.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
SPIN TROUBLE
Check the SENSOR SWITCH
ASSEMBLY or HOSE (Pressure).
If the problem is on the SENSOR
SWITCH ASSEMBLY or the
HOSE, replace the SENSOR
SWITCH ASSEMBLY or the
HOSE.
Check during spin if the frequency of the water
level is 248 or more.
Press the START/PAUSE button 2 times in QC
Test mode, is the drum spinning at low speed?
Normal
Is it disconnected, or disassembled?
[Red:3pin (1), NA:4pin (2)]
Correct the connection.
Check the motor connector, Is the resistance of
the terminal the same as the figure?
MOTOR TERMINAL
Replace the STATOR
ASSEMBLY
¥N ¥M ¥L
Resistance of terminal:
¥L-¥M/ ¥M-¥N/ ¥N-¥L About 5Ω 15Ω
Replace the MAIN PWB ASSEMBLY
Replace Door Assembly.
Does the spring of Latch Hook actuate?
Check the DOOR SWITCH
ASSEMBLY Connector and
MAIN PWB ASSEMBLY
(Red 4 pin and white 4 pin
connector (1)).
Is there clicking sound once or twice when the
START/PAUSE button is pressed to start the cycle?
Replace the DOOR
SWITCH ASSEMBLY.
Is DOOR SWITCH ASSEMBLY broken?
31
Download from Www.Somanuals.com. All Manuals Search And Download.
9. DISASSEMBLY INSTRUCTIONS
ƒRDisassemble and repair the unit only after pulling out power plug from the outlet.
1.
2.
Unscrew 7 screws on the Rear Frame.
Disassemble the Rear Frame.
3.
4.
5.
6.
Pull the Control panel forward.
Disconnect connectors.
Unscrew 5 screws.
Disassemble the controller assembly.
1.
2.
3.
4.
Open the Lid.
Unscrew 4 screws.
LID
Disassemble the Lid Assembly.
Pull down the Dispenser by pushing hooks.
5.
6.
Put a hand into the dispenser hole
and hold the top plate.
Push backward using an opener
and lift the top plate.
¡
Do first left side ( ).
¥L
32
Download from Www.Somanuals.com. All Manuals Search And Download.
1.
2.
Disassemble the 5 hose clamps.
Release the 5 hoses.
3.
Unscrew the nut at the lower
part of the dispenser.
4.
5.
Unscrew the 4 screws on the holder.
Disassemble the 5 connectors from the valves.
¡
¥L
¥N
¥P
¥M
¥O
Wire color :
WH-BK
WH-BK
BL-BK
OR-BK
GY-BK
1.
2.
Unscrew the screw from the top plate.
Unplug the 2 connectors.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
1.
2.
Unscrew the 2 screws from upper side of the
cabinet cover.
Unscrew the screw from filter cover.
3.
Put a flat (–) screwdriver into the both sides of
the filter cover, and pull it out.
4.
Unscrew the 2 screws from the lower side of the
cabinet cover.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
5.
6.
Open the door.
Disassemble the clamp assembly using
a flat (–) screwdriver.
7.
Separate the clamp assembly from cabinet
cover.
Clamp Assembly
8.
9.
Tilt the cabinet cover.
Disconnect the door switch connector.
10.
Lift and separate the cabinet cover.
11.
Disassemble the clamp assembly using
a flat (–) screwdriver.
12.
Disasemble the Gasket.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
1.
2.
Open the door.
Unscrew the 7 screws from the hinge cover.
3.
Put a flat (–) screwdriver into the opening of the
hinge, and pull out the hinge cover.
4.
5.
Unscrew the screws from the door.
Disassemble the door upward / downward.
¡
Be careful ! The door is heavy.
1.
2.
3.
Open the door.
Disassemble the clamp assembly.
Unscrew the 2 screws from cabinet cover.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
1.
2.
Disassemble the cabinet cover.
Separate the pump hose, the bellows
and the circulation hose assembly from the
pump assembly.
3.
Disassemble the pump assembly in arrow
direction.
1.
2.
3.
Disassemble the cabinet cover.
Separate 2 connectors from the heater.
Loose the nut and pull out the heater.
CAUTION
• When assembling the heater, insert the heater
into heater clip on the bottom of the tub.
• Tighten the fastening nut so the heater
is secure.
1.
2.
3.
Disassemble the cabinet cover.
Unplug the white connector from the thermistor.
Pull it out by holding the bracket of thermistor.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
1.
2.
3.
Disassemble the cabinet cover.
Separate the heater from the tub.
Remove any foreign objects (wire, coin, etc.) by
inserting a long bar in the opening.
1.
Unscrew the 4 screws from the back cover.
2.
Unscrew the single screw from the lower-right
side of the cabinet.
3.
Disconnect the connector from PWB Harness.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
1.
2.
3.
Disassemble the back cover.
Loosen the bolt.
Pull out the Rotor.
4.
5.
6.
Unscrew the 2 screws from the tub bracket.
Loosen the 6 bolts on the stator.
Unplug the 2 connectors from the stator.
1.
2.
Disassemble the damper hinges from the tub
and base.
Separate the dampers.
NOTE
• Once removed, replace the damper pin
with new one.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
10. EXPLODED VIEW
10-1. CABINET & CONTROL PANEL ASSEMBLY
A125
A105
A160
F215
A490
A495
A154
A136
A303
40
Download from Www.Somanuals.com. All Manuals Search And Download.
10-2. DRUM & TUB ASSEMBLY
K123
K115
K111
F463
K122
F464
K125
K121
K101
F315
F463
K343
K340
K344
K345
F141
K105
41
Download from Www.Somanuals.com. All Manuals Search And Download.
10-3. DISPENSER ASSEMBLY
F301
F302
F170
F160
F300
F325
F324
F323
F322
F321
HOT (BLUE)
A275
COLD (RED)
A276
F436
F431
F441
F120
F430
F435
F440
F432
42
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Life Fitness Treadmill TR 4500HR User Manual
LifeWise Air Cleaner 63 1510 User Manual
Lincoln Electric Welding System IM725 User Manual
Linear Satellite Radio MCT 11 User Manual
Magnasonic Flat Panel Television 26604MHD User Manual
Marley Engineered Products Electric Heater 402A User Manual
Melissa Vacuum Cleaner 740 114 User Manual
Memorex Portable CD Player MP8806 User Manual
Metabo Air Compressor Classic 350 User Manual
Meyer Sound Speaker MTS 4A User Manual