LG Electronics Network Card USB Drive User Manual

1
Download from Www.Somanuals.com. All Manuals Search And Download.  
Welcome to USB Drive.  
This user guide is designed to help you to use USB Drive correctly and safely.  
Please read this information carefully before using USB Drive. Please pay  
special attention to the sections that describe USB Drive operation for the  
Operating System being used by your computer.  
Before Using USB Drive TM  
Safety Instructions  
These Safety Instructions include directions and precautions for you to follow  
when using USB Drive. The instructions aim to secure your safety and to  
prevent any damage to your computer, your USB Drive and your data.  
Warning instructions indicate that failure to follow the directions could result in  
possible personal injuries.  
Caution instructions indicate that failure to follow the directions could result in  
damage to the USB Drive or data.  
Warning  
- To reduce the possibility of electrical shock, do not use the USB Drive if wet  
with any liquids such as water or chemicals.  
- To reduce the possibility of an electrical short circuit, do not plug the  
USB Drive into your computer’s USB port if it is wet. Plugging a wet USB Drive  
in causes a danger of damaging the USB Drive and/or your computer.  
- If any smoke or strange smells or noise occurs when using USB Drive, be sure  
to turn off your computer and peripheral devices immediately and disconnect  
the power cords.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Caution  
- Do not disconnect the USB Drive from the computer’s USB port while  
transferring (reading or writing) data. This will probably result in your data being  
corrupted  
- Make sure that you follow the instructions given in this guide when using or  
removing the product. Incorrect use of USB Drive may cause a malfunction of  
the product and/or loss of your data.  
- Be careful not to bend or twist the USB Drive. Do not place any heavy object  
on the product.  
- Please do not attempt to disassemble or modify the product.  
It can cause malfunction of the product. There are no user serviceable parts  
in the USB Drive.  
- Do not use your USB Drive in any place exposed to the following conditions,  
as it may cause a malfunction of the product : excessive vibration or shock;  
wetness, moisture or dust; heat and/or high temperature variation; strong  
electrical discharge; strong magnetic interference.  
- Be careful that any foreign material does not enter the insertion holes of USB  
Drive.  
LG Electronics Inc. assumes no responsibility for any corruption or loss of data  
and accompanying results due to incorrect use of the product.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
What is USB Drive TM?  
USB Drive™ is a removable, portable, flash memory based data storage device  
that works via your computer’s Universal Serial Bus (USB) interface. USB Drive  
does not require a battery or any external power because the USB Drive uses  
the power supplied by the computer or USB device it is plugged into. USB Drive  
works with your computer’s plug-and-play system,  
For most operating systems, once it is plugged into the USB port of your  
computer. It is ideal for mobile professionals, or for anyone with a need to move  
data frequently and conveniently between devices or networks, since it is very  
small and lightweight. Through SecureCell™ Utility, you can make USB Drive  
to be security-enabled, bootable disk-enabled. The Security feature is  
currently compatible with Microsoft Windows XP, 2000, ME, 98 and 98SE.  
Formatting USB Drive  
USB Drive has already been formatted and initialized with the FAT file system  
before delivery and is ready for immediate use.  
Operating System Requirements  
Operating Systems  
Driver Installation  
1. Microsoft Windows ME/2000/XP  
2. Mac OS 9.0 or higher  
3. Linux 2.4.0 or higher  
None required  
4. Microsoft Windows CE 3.0 or higher.  
1.Microsoft Windows 98/98SE  
Required  
When using Microsoft Windows ME/2000/XP, MAC 9.0 or  
higher, Linux 2.4.0 or higher, USB Drive can be installed and  
removed without powering down your computer. When using  
Microsoft Windows 98/98SE, you must install additional drivers  
before you can use the USB Drive.  
The additional Windows 98/98SE drivers can be downloaded  
from the www.lge.com homepage or loaded from your  
included CD-ROM. For Linux, it is required to mount SCSI.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installing/Using USB Drive in Windows ME/2000/XP  
1. Start Windows ME, Windows 2000 or Windows XP.  
2. Remove the cover from your USB Drive and plug it into a USB port  
on your computer.  
If it is the first time to use USB Drive, Windows will automatically recognize it  
and install all required drivers.  
3. The red Status LED will flash during the recognition and installation  
procedures. When USB Drive is ready to use, the Status LED will turn off.  
4. Click My Computer on Windows Desktop. USB Drive is displayed as a  
removable disk, as is shown in the following figure.  
(The drive name may be different depending on the system you are using).  
5. You can now read or write data using the installed USB Drive, the same as  
with any other hard drive.  
Removing USB Drive in Microsoft Windows ME/2000/XP  
1. Close all files currently opened from USB Drive.  
2. Click Safely Remove Hardware Icon on the Task Bar or the System Tray as  
shown in the following figure.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Select to remove hardware.  
4. When your computer indicates it is acceptable to remove hardware, then  
unplug the USB Drive from the USB port.  
Caution: Never remove or unplug USB Drive while the Red Status LED is  
flashing. Doing this may cause corruption of the data being transferred.  
Installing/Using USB Drive in Microsoft Windows 98/98SE  
For Microsoft Windows 98/98SE, you need to install new drivers for the  
USB Drive to operate. If you do not have the driver installation CD-ROM,  
you can download it from www.lge.com.  
Installing USB Driver  
1. Start Windows 98 or Windows 98SE.  
2. Insert the provided CD into CD-ROM Drive.  
3. Click [SecureCell Utility] in the CD.  
(Not insert USB Drive to USB port of your PC, Include Windows 98/98SE Device  
Driver)  
4.The Install Shield Wizard of Windows98 Device Driver or SecureCell Utility appears ,  
as shown in the following figure.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. You must restart your computer.  
6. After taking off the cap of the USB Drive and insert it to USB port of your PC, then it  
is recognized by the PC as a Removable Disk automatically.  
7. Click Uninstall button when you want to delete the Windows98 Device Driver.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Caution : When Window98 Device Driver is removed, Securecell Utility  
will be also removed.  
Removing USB Drive in Microsoft Windows 98/98SE  
1. Close all files currently opened from USB Drive.  
2. Unplug USB Drive from the USB port.  
Caution: Never remove or unplug USB Drive while the Red status  
LED is flashing.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installing/Using USB Drive in MacOS ( MacOS 9.0 or higher )  
1. Start MacOS.  
2. Remove the cover from your USB Drive and plug it into an USB port of your  
MAC.  
If it is the first time to use USB Drive, MAC will automatically recognize it.  
3. USB Drive is recognized as an [untitled] folder in MAC.  
4. You can read or write data using USB  
Drive, just the same as with any other  
hard disk drive.  
5. If your O.S version is the MacOS 8.6,  
please download a driver from  
http://www.apple.com and install the  
driver to your computer.  
Removing USB Drive  
1. Close all files currently opened from USB Drive.  
2. Drag and drop the [untitled] folder to the Recycle Bin.  
3. Unplug USB Drive from the USB port.  
Caution: Never remove or unplug USB Drive while the Red Status  
LED is flashing. Doing this may cause corruption of the data  
being transferred.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the SecureCell Utility  
Through SecureCell Utility, you can make USB Drive security-enabled,  
bootable disk-enabled. Security feature is currently compatible with only  
Windows XP/ 2000/ME/98SE/98.  
1. Plug USB Drive directly into your computer’s USB port.  
2. After your USB Drive is recognized, insert the CD-ROM included with your  
purchase.  
3. Once the CD-ROM is initialized, a pop-up menu will be displayed.  
4. Click on the menu item named [SecureCell Utility Setup].  
5. Once SecureCell Utility has launched, you will see the following application  
screen (Figure 1).  
6. [Disk Format]  
Click the Disk Format on Type of Format.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Figure 1  
Figure 2  
Figure 3  
- Click “O.K” button to start formatting. After finishing the procedure, click  
“OK” button again. (Figure 2, Figure 3)  
There are three kinds of formatting, Standard, Security, and Standard and  
Security. Those are used for under single or two partitions environment.  
To use the password function, please make sure your disk to have  
dual-partition.  
Please pay attention to select target drive when you want to format a drive  
since you use two partitions.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7. [Change Device Name]  
-
If you want to change Device Name, click the “Change Device Name”  
button and follow the instructions as following figures.  
Figure 4  
Figure 5  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Figure 6  
8. [Set Password]  
- The password mode is enabled after making dual partition, click the Set  
Password on Password Mode. (Figure 7)  
Figure 7  
Figure 8  
-
Input your Password New and Confirm. Confirm Password must be the  
same as New Password. (Figure 8)  
-
-
Click OK, your New Password is now in effect.  
When you remove and re-plug the device into computer, a window will be  
displayed and request you to enter your password. Enter your password  
and click the “OK” button. (Figure 9)  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Figure 9  
NOTE: You can’t access USB Drive if you lost your password. Because you  
can’t recover the saved data, please keep attention for your password.  
8. [To change Password]  
To change password, click the right button on icon in the System Tray and  
select the “Utility” menu.  
Than you can show a window as Figure 10.  
Enter previous password and new password, which you want to use and click  
the “OK” button. (Figure 11)  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Figure 10  
Figure 11  
9. [To divide partition]  
You can divide a USB Drive to two partition for your convenience purpose.  
Follow the instructions as following figures.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Figure 12  
Figure 13  
Figure 14  
Figure 15  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Figure 16  
9. [OPTIONS]  
-
-
[Show tray icon while device plugged]  
: Sets flag for displaying icon, which shows existence of USB Drive.  
[Check Password auto pop up]  
: Sets flag for displaying an window which requests you to enter  
password.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
USB Drive™ FAQ  
ell  
Q. I do not have any driver CD-ROM. What can I do?  
A. Go to the www.lge.com website and download and install the driver installation  
program.  
Q. What operating systems does USB Drive work with?  
A. USB Drive works with Microsoft Windows 98/98SE/ME/2000/XP, Mac, Linux and  
WinCE.  
Q. My computer does not recognize USB Drive.  
A. Click Start Settings Control Panel System and select Device Manager tab.  
Then check whether your computer has a USB controller.  
When your computer has a USB controller:  
If USB Drive is configured as an unknown device, remove it by clicking [Remove] and  
install the driver again.  
If USB Drive is not configured as an unknown device, re-install the driver using the New  
Hardware Installation applet.  
Q. I plugged USB Drive into the USB port of my computer. But I still can not find  
the “removable disk” icon from my computer or Windows Explorer?  
A. Please unplug USB Drive and plug again. If your operating system is Microsoft  
Windows 98/98SE, ensure that you have correctly installed the driver.  
Q. I have deleted data from USB Drive by chance. What can I do?  
A. USB Drive operates the same way as a hard disk drive. You can not recover the  
data once it has been deleted.  
Q. USB Drive is soaked in water. What can I do?  
A. Please dry USB Drive completely prior to plugging it again. If you use USB Drive  
while it is wet, the internal circuitry of USB Drive may malfunction, and thus not operate  
correctly.  
Q. Bad sectors have been found in USB Drive. How can I fix them?  
A. The manufactures of flash memory used in USB Drive only deliver the flash memory  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
that has less than 2% bad sector. Sometimes, bad sectors can be generated during  
using USB Drive. To remove bad sectors, download SecureCell Utility from  
www.lge.com website and format your USB Drive using it.  
Q. I want to use USB Drive in other computers but I do not have the driver  
installation CD.  
A. The best advantage of USB Drive is that it supports 'hot-plug' for Microsoft Windows  
ME/2000/XP, MAC 9.0 or higher, Linux 2.4.0 or higher. It means that you need not to  
install any driver if the operating system is one of those. Just plug your  
USB Drive to the USB port of the desired computer. If you are using Microsoft Windows  
98/98SE, you need to install the driver. For the driver, please download the installation  
program from www.lge.com  
Q. Can I print files directly from USB Drive?  
A. Yes. Open the file from USB Drive using an application program, like Microsoft Word,  
prior to printing it, and then use the printing mechanism of that application.  
Q. My computer locks once USB Drive is plugged into the USB port.  
A. Please remove USB Drive and restart your computer. After the booting is finished  
completely, plug USB Drive again into the USB port.  
Q. Does USB Drive work for Windows NT?  
A. No. Windows NT does not support mass storage devices that use USB interface.  
Q. Can USB Drive be infected by computer virus?  
A. Since USB Drive is a mass storage device. It can be infected by a computer virus.  
Once your USB Drive has been infected by a computer virus, you can cure it using the  
corresponding vaccine program.  
Q. I want to change the name of "Removable Disk" given to USB Drive.  
A. You can change the name any time during using your USB Drive if it has been  
properly installed. Once USB Drive has been renamed, the new name will always  
appear, until you rename it again.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Q. Can I set a password for the files to be saved in USB Drive?  
A. Every word processing program supports a password function for the file to prevent  
any unauthorized access to the documents. Once you set a password, other people  
cannot open the file.  
Q. I formatted USB Drive for the NTFS file system. Can it be used in other  
operating system?  
A. Microsoft Windows 98, 98SE and ME does not recognize the NTFS file system. If you  
want your USB Drive compatible for all operating systems, format it for FAT because all  
listed operating systems support it.  
Q. How long can I use USB Drive?  
A. The lifetime of USB Drive is related with the expected lifespan of flash memory. Like  
all semiconductor technology, flash memory has no moving parts and is expected to last  
for many years.  
Q. Does USB Drive need the driver to be installed?  
A. You need to install the driver only for Microsoft Windows 98/98SE, because it does  
not support mass storage device completely. You need not to install any driver for other  
Windows systems, Mac, and Linux.  
Q. Can I use USB Drive in version 1.1?  
A. Yes.  
Q. How many USB Drive can be connected at the same time?  
A. Theoretically, you can connect up to 127 USB Drive to a computer at the same time.  
If your computer is lack of available USB ports, you can expand the number of available  
ports by using a USB hub.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
The appearance and specifications can change for enhancements of the product without  
prior notice.  
Model  
USB DriveTM  
Storage capacity  
Interface  
32MB/64MB/128MB/256MB/512MB  
USB Spec 2.0  
Maximum data rate  
Power  
480Mbps/  
USB bus-powered (4.5V~5.5V)  
0°C ~ 45°C / 5% ~ 95%  
Operating Temperature  
Storage Humidity  
Dimensions (including cabinet)  
Weight (including cabinet)  
70mm x 22mm x 10mm  
9g  
Package includes:  
USB Drive, CD-ROM with User’s manual and Drivers, USB extension, Neck Strap  
cable and Warranty Card.  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Learning Resources Games LER 1576 User Manual
Lenovo Computer Drive 40Y8699 User Manual
Lenovo Computer Hardware 6137 User Manual
Lenovo Personal Computer TC A51 8122 User Manual
Lincoln Electric Welder 11079 User Manual
Lopi Indoor Fireplace Yankee Bay Pellet Insert User Manual
Mackie Car Speaker SWA 1801z User Manual
Manhattan Computer Products Satellite TV System XT F User Manual
Mellerware Hot Beverage Maker 22550 User Manual
MicroBoards Technology DVD Recorder LightScribe Series User Manual