/0%2!4)/. '5)$% (Rev. 1.2.)
FS-C5100DN/C5200DN/C5300DN
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Legal and Safety Information
CAUTION NO LIABILITY IS ASSUMED FOR ANY
DAMAGE CAUSED BY IMPROPER INSTALLATION.
Notice on Software
SOFTWARE USED WITH THIS PRINTER MUST SUPPORT THE
PRINTER'S EMULATION MODE. The printer is factory-set to emulate the
PCL.
Notice
The information in this guide is subject to change without notification.
Additional pages may be inserted in future editions. The user is asked to
excuse any technical inaccuracies or typographical errors in the present
edition.
No responsibility is assumed if accidents occur while the user is following
the instructions in this guide. No responsibility is assumed for defects in
the printer's firmware (contents of its read-only memory).
This guide, any copyrightable subject matter sold or provided with or in
connection with the sale of the page printer, are protected by copyright.
All rights are reserved. Copying or other reproduction of all or part of this
guide, any copyrightable subject matter without the prior written consent
of Kyocera Mita Corporation is prohibited. Any copies made of all or part
of this guide, any copyrightable subject must contain the same copyright
notice as the material from which the copying is done.
Regarding Tradenames
PRESCRIBE is a registered trademark of Kyocera Corporation. KPDL is
trademark of Kyocera Corporation.
Hewlett-Packard, PCL, and PJL are registered trademarks of Hewlett-
Packard Company. Centronics is a trade name of Centronics Data
Computer Inc. PostScript is a registered trademark of Adobe Systems
Incorporated. Macintosh is a registered trademark of Apple Computer,
Inc. Microsoft, Windows, and Windows NT are registered trademarks of
Microsoft Corporation. PowerPC and Microdrive are trademarks of
International Business Machines Corporation. CompactFlash is a
trademark of SanDisk Corporation. ENERGY STAR is a U.S. registered
mark. All other brand and product names are registered trademarks or
trademarks of their respective companies.
This product was developed using the Tornado™ Real Time Operating
System and Tools from Wind River Systems.
This product contains UFST™ and MicroType® from Monotype Imaging
Inc.
v
Download from Www.Somanuals.com. All Manuals Search And Download.
License Agreements
Typeface Trademark Acknowledgement
All resident fonts in this printer are licensed from Monotype Imaging Inc.
Helvetica, Palatino and Times are registered trademarks of Linotype-Hell
AG. ITC Avant Garde Gothic, ITC Bookman, ITC ZapfChancery and ITC
Zapf Dingbats are registered trademarks of International Typeface
Corporation.
Monotype Imaging License Agreement
1
“Software” shall mean the digitally encoded, machine readable,
scalable outline data as encoded in a special format as well as the
UFST Software.
2
You agree to accept a non-exclusive license to use the Software to
reproduce and display weights, styles and versions of letters,
numerals, characters and symbols (“Typefaces”) solely for your own
customary business or personal purposes at the address stated on
the registration card you return to Monotype Imaging. Under the
terms of this License Agreement, you have the right to use the Fonts
on up to three printers. If you need to have access to the fonts on
more than three printers, you need to acquire a multi-user license
agreement which can be obtained from Monotype Imaging.
Monotype Imaging retains all rights, title and interest to the Software
and Typefaces and no rights are granted to you other than a License
to use the Software on the terms expressly set forth in this
Agreement.
3
To protect proprietary rights of Monotype Imaging, you agree to
maintain the Software and other proprietary information concerning
the Typefaces in strict confidence and to establish reasonable
procedures regulating access to and use of the Software and
Typefaces.
4
5
You agree not to duplicate or copy the Software or Typefaces,
except that you may make one backup copy. You agree that any
such copy shall contain the same proprietary notices as those
appearing on the original.
This License shall continue until the last use of the Software and
Typefaces, unless sooner terminated. This License may be
terminated by Monotype Imaging if you fail to comply with the terms
of this License and such failure is not remedied within thirty (30)
days after notice from Monotype Imaging. When this License expires
or is terminated, you shall either return to Monotype Imaging or
destroy all copies of the Software and Typefaces and documentation
as requested.
6
7
You agree that you will not modify, alter, disassemble, decrypt,
reverse engineer or decompile the Software.
Monotype Imaging warrants that for ninety (90) days after delivery,
the Software will perform in accordance with Monotype Imaging-
published specifications, and the diskette will be free from defects in
material and workmanship. Monotype Imaging does not warrant that
the Software is free from all bugs, errors and omissions.
8
THE PARTIES AGREE THAT ALL OTHER WARRANTIES,
EXPRESSED OR IMPLIED, INCLUDING WARRANTIES OF
FITNESS FOR A PARTICULAR PURPOSE AND
MERCHANTABILITY, ARE EXCLUDED.
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Your exclusive remedy and the sole liability of Monotype Imaging in
connection with the Software and Typefaces is repair or replacement
of defective parts, upon their return to Monotype Imaging.
10 IN NO EVENT WILL MONOTYPE IMAGING BE LIABLE FOR LOST
PROFITS, LOST DATA, OR ANY OTHER INCIDENTAL OR
CONSEQUENTIAL DAMAGES, OR ANY DAMAGES CAUSED BY
ABUSE OR MISAPPLICATION OF THE SOFTWARE AND
TYPEFACES.
11 Massachusetts U.S.A. law governs this Agreement.
12 You shall not sublicense, sell, lease, or otherwise transfer the
Software and/or Typefaces without the prior written consent of
Monotype Imaging.
13 Use, duplication or disclosure by the Government is subject to
restrictions as set forth in the Rights in Technical Data and Computer
Software clause at FAR 252-227-7013, subdivision (b)(3)(ii) or
subparagraph (c)(1)(ii), as appropriate. Further use, duplication or
disclosure is subject to restrictions applicable to restricted rights
software as set forth in FAR 52.227-19 (c)(2).
14 YOU ACKNOWLEDGE THAT YOU HAVE READ THIS
AGREEMENT, UNDERSTAND IT, AND AGREE TO BE BOUND BY
ITS TERMS AND CONDITIONS. NEITHER PARTY SHALL BE
BOUND BY ANY STATEMENT OR REPRESENTATION NOT
CONTAINED IN THIS AGREEMENT. NO CHANGE IN THIS
AGREEMENT IS EFFECTIVE UNLESS WRITTEN AND SIGNED
BY PROPERLY AUTHORIZED REPRESENTATIVES OF EACH
PARTY. BY OPENING THIS DISKETTE PACKAGE, YOU AGREE
TO ACCEPT THE TERMS AND CONDITIONS OF THIS
AGREEMENT.
GPL
Firmware of this machine is using in part the GPL applied codes
applied codes available.
Open SSLeay License
Copyright © 1998-2006 The OpenSSL Project. All rights reserved.
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions are met:
1
2
Redistributions of source code must retain the above copyright
notice, this list of conditions and the following disclaimer.
Redistributions in binary form must reproduce the above copyright
notice, this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the distribution.
3
4
5
All advertising materials mentioning features or use of this software
must display the following acknowledgment:
"This product includes software developed by the OpenSSL Project
for use in the OpenSSL Toolkit. (http://www.openssl.org/)"
The names "OpenSSL Toolkit" and "OpenSSL Project" must not be
used to endorse or promote products derived from this software
without prior written permission.
For written permission, please contact [email protected].
Products derived from this software may not be called "OpenSSL"
nor may "OpenSSL" appear in their names without prior written
permission of the OpenSSL Project.
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Redistributions of any form whatsoever must retain the following
acknowledgment: "This product includes software developed by the
OpenSSL Project for use in the OpenSSL Toolkit (http://
www.openssl.org/)"
THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT "AS IS"
AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE DISCLAIMED. IN NO EVENT SHALL THE OpenSSL PROJECT OR
ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN
IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Original SSLeay License
Copyright © 1995-1998 Eric Young ([email protected]) All rights
reserved.
This package is an SSL implementation written by Eric Young
([email protected]). The implementation was written so as to conform
with Netscapes SSL.
This library is free for commercial and non-commercial use as long as the
following conditions are aheared to. The following conditions apply to all
code found in this distribution, be it the RC4, RSA, lhash, DES, etc., code;
not just the SSL code. The SSL documentation included with this
distribution is covered by the same copyright terms except that the holder
is Tim Hudson ([email protected]).
Copyright remains Eric Young's, and as such any Copyright notices in the
code are not to be removed.
If this package is used in a product, Eric Young should be given attribution
as the author of the parts of the library used.
This can be in the form of a textual message at program startup or in
documentation (online or textual) provided with the package.
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions are met:
1
2
Redistributions of source code must retain the copyright notice, this
list of conditions and the following disclaimer.
Redistributions in binary form must reproduce the above copyright
notice, this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the distribution.
3
All advertising materials mentioning features or use of this software
must display the following acknowledgement:
"This product includes cryptographic software written by Eric Young
The word 'cryptographic' can be left out if the rouines from the library
being used are not cryptographic related :-).
viii
Download from Www.Somanuals.com. All Manuals Search And Download.
4
If you include any Windows specific code (or a derivative thereof)
from the apps directory (application code) you must include an
acknowledgement:
"This product includes software written by Tim Hudson
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG "AS IS" AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE
FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,
OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED
TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE
USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY
OF SUCH DAMAGE.
The licence and distribution terms for any publically available version or
derivative of this code cannot be changed. i.e. this code cannot simply be
copied and put under another distribution licence [including the GNU
Public Licence.]
ix
Download from Www.Somanuals.com. All Manuals Search And Download.
Compliance and Conformity
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
• The use of a non-shielded interface cable with the referenced device
is prohibited.
CAUTION — The changes or modifications not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
This device complies with Part 15 of FCC Rules and RSS-Gen of IC
Rules.
Operation is subject to the following two conditions; (1) this device may
not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
* The above warning is valid only in the United States of America.
Interface connectors
IMPORTANT Be sure to power off the printer before connecting or
disconnecting an interface cable. For protection against static
electricity discharge to the printer's internal electronics through the
interface connector(s), cover any interface connector that is not in use
with the protective cap supplied.
Note Use shielded interface cables.
x
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Information
Laser Safety
This printer is certified as a Class 1 laser product under the U.S.
Department of Health and Human Services (DHHS) Radiation
Performance Standard according to Radiation Control for Health and
Safety Act of 1968. This means that the printer does not produce
hazardous laser radiation. Since radiation emitted inside the printer is
completely confined within protective housings and external covers, the
laser beam cannot escape from the printer during any phase of user
operation.
Laser Notice
This printer is certified in the U.S. to conform to the requirements of DHHS
21 CFR Subchapter for Class I (1) laser products, and elsewhere is
certified as a Class I laser product conforming to the requirements of IEC
825.
DANGER CLASS 3B INVISIBLE LASER RADIATION
WHEN OPEN. AVOID DIRECT EXPOSURE TO BEAM.
CAUTION Use of controls or adjustments or performance
of procedures other than those specified herein may result
in hazardous radiation exposure.
Radio Frequency Transmitter
This machine contains a transmitter module. We, the manufacturer
(Kyocera Mita Corporation) hereby declare that this equipment (page
printer), model FS-C5100DN, FS-C5200DN and FS-C5300DN are in
compliance with the essential requirements and other relevant provisions
of Directive 1999/5/EC.
Radio Tag Technology
In some countries, the radio tag technology used in this equipment to
identify the toner container may be subject to authorization, and the use
of this equipment may consequently be restricted.
xi
Download from Www.Somanuals.com. All Manuals Search And Download.
Cautionary Labels
The printer bears any of the following labels.
High temperature inside. Do
not touch parts in this area,
because there is a danger of
getting burned.
Label inside the printer (Laser radiation warning)
For Europe, Asia, and other countries
For U.S.A. and Canada
xii
Download from Www.Somanuals.com. All Manuals Search And Download.
CDRH Regulations
The Center for Devices and Radiological Health (CDRH) of the U.S. Food
and Drug Administration implemented regulations for laser products on
August 2, 1976. These regulations apply to laser products manufactured
after August 1, 1976. Compliance is mandatory for products marketed in
the United States. A label indicating compliance with the CDRH
regulations must be attached to laser products marketed in the United
States.
Ozone concentration
The printers generate ozone gas (O3) which may concentrate in the place
of installation and cause an unpleasant smell. To minimize the
concentration of ozone gas to less than 0.1 ppm, we recommend you not
to install the printer in a confined area where ventilation is blocked.
Safety Instructions Regarding the Disconnection of Power
Caution: The power plug is the main isolation device! Other switches on
the equipment are only functional switches and are not suitable for
isolating the equipment from the power source.
VORSICHT: Der Netzstecker ist die Hauptisoliervorrichtung! Die anderen
Schalter auf dem Gerät sind nur Funktionsschalter und können nicht
verwendet werden, um den Stromfluß im Gerät zu unterbrechen.
DECLARATION OF CONFORMITY
TO
2004/108/EC, 2006/95/EEC, 93/68/EEC and 1999/5/EC
We declare under our sole responsibility that the product to which this
declaration relates is in conformity with the following specifications.
EN55024
EN55022 Class B
EN61000-3-2
EN61000-3-3
EN60950-1
EN60825-1
EN300 330-1
EN300 330-2
xiii
Download from Www.Somanuals.com. All Manuals Search And Download.
Canadian Department of Communications Compliance
Statement
This Class B digital apparatus complies with Canadian ICES-003.
Avis de conformité aux normes du ministère des
Communications du Canada
Cet appareil numérique de la classe B est conforme à la norme NMB-003
du Canada.
EN ISO 7779
Maschinenlärminformations-Verordnung 3. GPSGV, 06.01.2004: Der
höchste Schalldruckpegel beträgt 70 dB (A) oder weniger gemäß EN ISO
7779.
Disclaimer
Kyocera Mita will not be liable to customers or any other person or entity
for any loss or damage caused or alleged to be caused directly or
indirectly by equipment sold or furnished by us, including but not limited
to, any interruption of service, loss of business or anticipatory profits, or
consequential damages resulting from the use or operation of the
equipment or software.
xiv
Download from Www.Somanuals.com. All Manuals Search And Download.
Energy Saving Control Function
The device comes equipped with a Sleep Mode where printer functions
remain in a waiting state but power consumption is still reduced to a
minimum when there is no activity with the device within a set amount of
time.
Sleep
The device automatically enters Sleep when 30 minutes have passed
since the device was last used. The amount of time of no activity that must
pass before Sleep is activated may be lengthened. For more information,
refer to Sleep Timer (Sleep timer timeout setting) section of the Advanced
Operation Guide.
Automatic 2-Sided Print Function
This device includes 2-sided printing as a standard function. For example,
by printing two 1-sided originals onto a single sheet of paper as a 2-sided
print, it is possible to lower the amount of paper used. For more
information, refer to Duplex (Duplex Printing) section of the Advanced
Operation Guide.
Paper Recycling
This device supports the recycled paper which reduces the load on the
environment. Your sales or service representative can provide
information about recommended paper types.
Energy Star (ENERGY STAR®) Program
We have determined as a participating company in the International
Energy Star Program that this product is compliant with the standards laid
out in the International Energy Star Program.
xv
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Precautions
Environment
CAUTION Avoid placing the printer on or in locations which
are unstable or not level. Such locations may cause the
printer to fall. This type of situation presents a danger of
personal injury or damage to the printer.
Avoid locations with humidity or dust and dirt. If dust or dirt
becomes attached to the power plug, clean the plug to avoid
the danger of fire or electrical shock.
Avoid locations near radiators, heaters, or other heat
sources, or locations near flammable items, to avoid the
danger of fire.
To keep the printer cool and facilitate changing of parts and
maintenance, allow access space as shown below. Leave
adequate space, especially around the side cover, to allow
air to be properly ventilated from the printer.
Top: 400 mm
(16 inches)
Left: 400 mm
(16 inches)
Right: 250 mm
(10 inches)
Rear: 200 mm
(7-7/8 inches)
Front: 600 mm
(23-5/8 inches)
Other Precautions
Adverse environmental conditions may affect the safe operation and
performance of the printer. Install in an air-conditioned room
(recommended room temperature: around 23 °C, humidity: around 60 %
RH) and avoid the following locations when selecting a site for the printer.
-
-
-
-
-
Avoid locations near a window or with exposure to direct sunlight.
Avoid locations with vibrations.
Avoid locations with drastic temperature fluctuations.
Avoid locations with direct exposure to hot or cold air.
Avoid poorly ventilated locations.
If the flooring is of a soft material, it may be damaged by the casters when
this product is moved after installation.
xvi
Download from Www.Somanuals.com. All Manuals Search And Download.
Power Supply/Grounding the Printer
WARNING Do not use a power supply with a voltage other
than that specified. Avoid multiple connections in the same
outlet. These types of situations present a danger of fire or
electrical shock.
Plug the power cord securely into the outlet. If metallic objects
come in contact with the prongs on the plug, it may cause a fire
or electric shock.
Always connect the printer to an outlet with a ground
connection to avoid the danger of fire or electrical shock in
case of an electric short. If an earth connection is not possible,
contact your service representative.
Other Precautions
Connect the power plug to the closest outlet possible to the printer.
Handling of Plastic Bags
WARNING Keep the plastic bags that are used with the
printer away from children. The plastic may cling to their
nose and mouth causing suffocation.
xvii
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions for Use
Cautions when Using the Printer
• Do not place metallic objects or containers with water (flower vases,
flower pots, cups, etc.) on or near the printer. This type of situation
presents a danger of fire or electrical shock should they fall inside.
• Do not remove any of the covers from the printer as there is a danger
of electrical shock from high voltage parts inside the printer.
• Do not damage, break or attempt to repair the power cord. Do not
place heavy objects on the cord, pull it, bend it unnecessarily or cause
any other type of damage.These types of situations present a danger
of fire or electrical shock.
• Never attempt to repair or disassemble the printer or its parts as there
is a danger of fire, electrical shock or damage to the laser. If the laser
beam escapes, there is a danger of it causing blindness.
• If the printer becomes excessively hot, smoke appears from the
printer, there is an odd smell, or any other abnormal situation occurs,
there is a danger of fire or electrical shock. Turn the power switch
OFF ({) immediately, remove the power plug from the outlet and
contact your service representative.
• If anything harmful (paper clips, water, other fluids, etc.) falls into the
printer, turn the power switch OFF ({) immediately. Next, remove the
power plug from the outlet to avoid the danger of fire or electrical
shock. Then contact your service representative.
• Do not remove or connect the power plug with wet hands, as there is
a danger of electrical shock.
• Always contact your service representative for maintenance or repair
of internal parts.
• Do not pull the power cord when removing it from the outlet. If the
power cord is pulled, the wires may become broken and there is a
danger of fire or electrical shock. (Always grasp the power plug when
removing the power cord from the outlet.)
• Always remove the power plug from the outlet when moving the
printer. If the power cord is damaged, there is a danger of fire or
electrical shock.
• If the printer will not be used for a short period of time (overnight, etc.),
turn the power switch OFF ({). If it will not be used for an extended
period of time (vacations, etc.), remove the power plug from the outlet
for safety purposes during the time the printer is not in use.
• For safety purposes, always remove the power plug from the outlet
when performing cleaning operations.
• If dust accumulates within the printer, there is a danger of fire or other
trouble. It is therefore recommended that you consult with your
service representative in regard to cleaning of internal parts. This is
particularly effective if accomplished prior to seasons of high humidity.
Consult with your service representative in regard to the cost of
cleaning the internal parts of the printer.
xviii
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Precautions
• Do not place heavy objects on the printer or cause other damage to
the printer.
• Do not open the top/left/rear cover, turn off the main switch, or pull out
the power plug during printing.
• During printing, some ozone is released, but the amount does not
cause any ill effect to one's health. If, however, the printer is used over
a long period of time in a poorly ventilated room or when printing an
extremely large number of copies, the smell may become unpleasant.
To maintain the appropriate environment for print work, it is suggested
that the room be properly ventilated.
• Do not touch electrical parts, such as connectors or printed circuit
boards. They could be damaged by static electricity.
• Do not attempt to perform any operations not explained in this
handbook.
• If the printer will not be used for an extended period of time, remove
the paper from the cassette, return it to its original package and reseal
it.
CAUTION Use of controls or adjustments or performance
of procedures other than those specified herein may result
in hazardous radiation exposure.
Cautions for Toner Handling
• Do not incinerate toner and toner containers. Dangerous sparks may
cause burn.
• Never open the toner container.
• Do not inhale the toner.
• If you get toner on your hands, do not rub your eyes or touch your
mouth. Wash the toner from your hands.
• For the disposal of the old toner container, consult your service
technician or dispose of the toner or toner containers in accordance
with Federal, State and Local rules and regulations.
xix
Download from Www.Somanuals.com. All Manuals Search And Download.
About the Operation Guide
This Operation Guide has the following chapters:
This chapter explains the names of parts.
This chapter explains how to print from your workstation.
This chapter explains how to replace the toner container and how to care
for your printer.
This chapter explains how to handle printer problems that may occur,
such as paper jams.
This chapter lists the printer’s specifications.
Conventions
This manual uses the following conventions.
Convention
Description
Example
Used to emphasize a key word,
phrase or reference to additional
information.
To replace the toner container, refer to Toner
Container Replacement on page 3-2.
Italic Typeface
Used to denote buttons on the
software.
To start printing, click OK.
Bold
Used to denote operation panel
keys.
Press [GO] to resume printing.
Braket Bold
Note
Used to provide additional or useful
information about a function or
feature.
Note Check with your network
administrator for the network address
settings.
Used to provide important
information.
Important
Caution
IMPORTANT Ensure paper is not folded,
curled, or damaged.
Cautions are statements that
suggest mechanical damage as a
result of an action.
CAUTION Do not pull the cassette out
when holding the front of the machine.
Used to alert users to the possibility
of personal injury.
Warning
WARNING High voltage is present in the
charger section.
xx
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Machine Parts
This chapter provides explanations and illustrations for you to
determine the parts and their functions. Try to be familiar with
the names and functions of these parts for correct use and
optimal performance.
This chapter contains explanations on the following topics:
Machine Parts
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Components at the Front of the Printer
1
2
3
4
5
6
7
1
2
3
4
5
6
7
Operation Panel
Front Cover
Paper Stopper
Top Cover (Top Tray)
MP (Multi-Purpose) Tray
Paper Cassette
Power Switch
Components at the Left of the Printer
11 12 13 14
8
10
9
8
9
Left Cover
Waste Toner Box
10 Main Charger Units on the Drum Units
11 Magenta Toner Container (M)
12 Cyan Toner Container (C)
13 Yellow Toner Container (Y)
14 Black Toner Container (K)
1-2
MachineParts
Download from Www.Somanuals.com. All Manuals Search And Download.
Internal Components
15
16
17
18
15 Paper Transfer Unit
16 Paper Ramp
17 Duplex Unit
18 Envelope Switch
Components at the Rear of the Printer
19
25
20
21
22 23
24
19 USB Memory Slot
20 Power Cord Connector
21 Option Interface Slot
22 Network Indicators
23 Network Interface Connector
24 USB Interface Connector
25 Rear Cover
Machine Parts
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Network Interface Parameters
This printer supports TCP/IP, TCP/IP (IPv6), NetWare, AppleTalk, IPP,
SSL Server, IPSec protocols and Security Level. (For details refer to
Advanced Operation Guide.)
Note After all network related settings have been done, turn
the machine OFF and ON again. This is mandatory to make
the settings effective!
TCP/IP, TCP/IP (IPv6) settings
1 Press [MENU].
2 Press U or V repeatedly until Network >appears.
Network
>
>
3 Press Z. Each time you press U or V, the selection changes. Refer
to the explanations below when specifying the settings.
Set this item to Onwhen you connect to a network using TCP/IP.
Submenu has items including DHCP, IP Address, Subnet Mask,
Gatewayand Bonjour.
>TCP/IP
Off
Set this item to Onwhen you connect to a network using TCP/IP
(IPv6). Submenu has items including RA(Stateless)and
DHCPv6.
>TCP/IP (IPv6) >
Off
2-2
PrintingOperation
Download from Www.Somanuals.com. All Manuals Search And Download.
TCP/IP
This section describes how to enable the TCP/IP protocol.
1 If TCP/IPis set to Off, use U or V to select Onand press [OK].
>TCP/IP
On
>
2 Press Z. Each time you press U or V, the selection changes.
>>DHCP
Off
>>IP Address
000.000.000.000
>>Subnet Mask
000.000.000.000
>>Gateway
000.000.000.000
>>Bonjour
Off
3 Display the item you want to set and press [OK]. A blinking question
mark (?) appears while you are setting DHCPand Bonjour. A
blinking cursor (_) appears while you are setting IP Address,
Subnet Maskand Gateway.
>>Subnet Mask
000.000.000.000
4 Press U or V to select Onor Offas the setting for DHCPand
Bonjour.
For the IP Address, Subnet Maskand Gatewaysettings, press
U or V to move the blinking cursor to the number you want to change
(000to 255). Use Y and Z to move the cursor right and left.
Note Check with your network administrator for the network
address settings.
5 Press [OK].
6 Press [MENU]. The display returns to Ready.
Printing Operation
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
TCP/IP (IPv6)
This section describes how to enable the TCP/IP (IPv6) protocol.
1 If TCP/IP (IPv6)is set to Off, use U or V to selecto Onand press
>TCP/IP (IPv6) >
On
[OK].
2 Press Z. Each time you press U or V, the selection changes.
>>RA(Stateless)
Off
>>DHCPv6
Off
3 Display the item you want to set and press [OK]. A blinking question
mark (?) appears while you are setting RA(Stateless)and
DHCPv6.
>>RA(Stateless)
?Off
>>DHCPv6
?Off
4 Press U or V to select Onor Offas the setting for RA(Stateless)
and DHCPv6.
Note Check with your network administrator for the network
address settings.
5 Press [OK].
6 Press [MENU]. The display returns to Ready.
NetWare, AppleTalk, IPP, SSL Server, IPSec and Security
Level settings
1 Press [MENU].
2 Press U or V repeatedly until Security >appears.
Security
>
2-4
PrintingOperation
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Press Z. Each time you press U or V, the selection changes. Refer
to the explanations below when specifying the settings.
If you are using NetWare, AppleTalk, IPP, SSL Serveror IPSec
to connect to a network, you must enter an administrator ID. By
default, the administrator ID is the numeric part of your printer's model
name. If you use FS-C5300DN, enter "5300".
ID
_
If you are using NetWare, AppleTalk, IPP, SSL Serveror IPSec
to connect to a network, you must enter an administrator password.
By default, the administrator password is the numeric part of your
printer's model name. If you use FS-C5300DN, enter "5300".
Password
_
Set this item to Onwhen you connect to a network using NetWare. In
submenu, frame mode can be selected from Auto, 802.3,
Ethernet-II, SNAPand 802.2.
>NetWare
On
>
AppleTalkmust be activated (On) for networking with Macintosh
computers.
>AppleTalk
On
Set this item to Onwhen you connect to a network using IPP.
>IPP
Off
Set this item to Onwhen you connect to a network using SSL
Server. Submenu has items including DES, 3DES, AES, IPP over
SSLand HTTPS.
>SSL Server >
Off
Set this item to Onwhen you connect to a network using IPSec.
>IPSec
Off
Continued on next page.
Printing Operation
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Set the Security Levelto High.
>Security Level
High
NetWare
This section explains the procedure for enabling NetWare.
1 Enter the administrator ID and password. Then, if NetWareis set to
>NetWare
On
>
Off, use U or V to select Onand press [OK].
2 Press Z.
>>Frame Type
Auto
3 Press [OK]. A blinking question mark (?) appears. Each time you
>>Frame Type
?Auto
press U or V, the selection changes.
>>Frame Type
?802.3
>>Frame Type
?Ethernet-II
>>Frame Type
?SNAP
>>Frame Type
?802.2
4 Display the item you want to set and press [OK].
5 Press [MENU]. The display returns to Ready.
2-6
PrintingOperation
Download from Www.Somanuals.com. All Manuals Search And Download.
AppleTalk
This section explains the procedure for enabling AppleTalk.
1 Enter the administrator ID and password. Then, if AppleTalkis set
>AppleTalk
On
to Off, use U or V to select On.
2 Press [OK]. A blinking question mark (?) appears.
>AppleTalk
?On
3 Press [OK] again.
4 Press [MENU]. The display returns to Ready.
IPP
This section explains the procedure for enabling IPP.
1 Enter the administrator ID and password. Then, if IPPis set to Off,
>IPP
On
use U or V to select On.
2 Press [OK]. A blinking question mark (?) appears.
>IPP
?On
3 Press [OK] again.
4 Press [MENU]. The display returns to Ready.
Printing Operation
2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
SSL Server
This section explains the procedure for enabling SSL Server.
1 Enter the administrator ID and password. Then, if SSL Serveris set
>SSL Server >
On
to Off, use U or V to select Onand press [OK].
2 Press Z. Each time you press U or V, the selection changes.
>>DES
Off
>>3DES
Off
>>AES
Off
>>IPP over SSL
Off
>>HTTPS
Off
3 Display the item you want to set and press [OK]. A blinking question
>>DES
?Off
mark (?) appears.
4 Select Onor Offusing U or V.
5 Press [OK].
6 Press [MENU]. The display returns to Ready.
IPSec
This section explains the procedure for enabling IPSec.
1 Enter the administrator ID and password. Then, if IPSecis set to
>IPSec
On
Off, use U or V to select On.
2 Press [OK]. A blinking question mark (?) appears.
>IPSec
?On
3 Press [OK] again.
4 Press [Menu]. The display returns to Ready.
2-8
PrintingOperation
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Level
Security Levelis primarily a menu used by service personnel for
maintenance work. There is no need for customers to use this menu.
>Security Level
High
Printing Operation
2-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing a Network Interface Status Page
You can print out a status page for the network interface. The network
status page shows the network addresses, and other information under
various network protocols about the network interface.
Adjust/Maintenance
Adjust/Maintenance is used to adjust the print quality and to carry out
printer maintenance.
The options available in Adjust/Maintenance are as follows:
• Color Calibration
• Registration Normal
• Registration Details
• Restart Printer
• Service
IMPORTANT Serviceis primarily a menu used by service
personnel for maintenance work. There is no need for customers to
use this menu.
1 Press [MENU].
2 Press U or V repeatedly until Adjust/Maintenance >appears.
Adjust/
>
Maintenance
3 Press Z while Adjust/Maintenance >is displayed.
4 Press U or V repeatedly until >Service >appears.
5 Press Z.
6 Press U or V repeatedly until >>Print Network Status Page
appears.
7 Press [OK]. A question mark (?) appears.
>>Print Network
Status Page ?
8 Press [OK]. Processingappears and a status page is printed out.
9 When printing ends, the display returns to Ready.
2-10
PrintingOperation
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Printer Driver
Ensure the printer is plugged in and connected to the PC before installing
the printer driver from the CD-ROM.
Installing the Software in Windows
If you are connecting this printer to a Windows PC, follow the next steps
to install the printer driver. The example shows you how to connect your
printer to a Windows Vista PC.
Note In Windows Vista, Windows XP and Windows 2000, you
must be logged on with administrator privileges.
You can use either Express Mode or Custom Mode to install the software.
Express Mode automatically detects connected printers and installs the
required software. Use Custom Mode if you want to specify the printer
port and select the software to be installed.
1 Turn on the computer and start up Windows.
If the Welcome to the Found New Hardware Wizard dialog box
displays, select Cancel.
2 Insert the CD-ROM supplied with the printer into the optical drive of
the PC. In Windows Vista, the user account management window
appears. Click Allow.
The installation program launches.
Note If the software install wizard does not launch
automatically, open the CD-ROM window in Windows
Explorer and double-click Setup.exe.
3 Click View License Agreement and read the License Agreement.
Click Accept.
4 Click Install software.
The software install wizard starts up. Click Next.
From this point, the procedure differs depending on your version of
Windows and your connection method. Proceed to the correct
procedure for your connection type.
• Express Mode
• Custom Mode
Printing Operation
2-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Express Mode
In Express Mode, the installer automatically detects the printer when it is
turned on. Use Express Mode for standard connection methods.
1 In the installation method selection window, select Express Mode.
The print system detection window appears and the installer detects
the connected printers. If the installer does not detect a print system,
check that the print system is connected via USB or a network and
that it is turned on. Then return to the print system detection window.
Note While the information shown in Windows Vista and
Windows XP installation dialog boxes differs slightly, the
installation procedure is the same.
2 Select the print system to be installed and click Next.
Note If the Found New Hardware Wizard appears, click
Cancel. If a hardware installation warning message appear,
click Continue.
3 You can customize the print system name in the installation settings
window. This will be the name displayed in the Printer window and in
the printer lists displayed in applications. Specify whether to share the
print system name or set the print system as an existing printer and
then click Next.
IMPORTANT Step 3 only appears if the print system is connected
via a network. It does not appear if the print system is connected
via a USB.
4 A window appears in which you can check the settings. Check the
settings carefully and then click Install.
Note If the Windows security window appears, click Install
this driver software.
5 A message appears saying that the printer has been installed
successfully. Click Exit to exit the printer installation wizard and
return the CD-ROM main menu.
If the device setup dialog box appears after you click Exit, you can
specify the settings for items such as optional features installed in the
print system. You can also specify the device settings after you exit
the installation. For details, refer to Device Settings in the printer
driver operation manual on the CD-ROM.
This completes the printer driver installation procedure. Follow the
on-screen instructions to restart the system, if required.
2-12
PrintingOperation
Download from Www.Somanuals.com. All Manuals Search And Download.
Custom Mode
Use Custom Mode if you want to specify the printer port and select the
software to be installed.
For example, if you do not want fonts installed on your computer to be
replaced, select Custom Mode and deselect the Fonts checkbox in the
installation window.
1 Select Custom Mode.
2 Following the instructions in the install wizard window, select the
software packages to be installed and the specify the port, etc.
For details, refer to Custom Installation in the printer driver operation
manual on the CD-ROM.
Installation on a Macintosh
1 Turn on the printer and the Macintosh.
2 Insert the included CD-ROM (Product Library) into the CD-ROM
drive.
3 Double-click the CD-ROM icon.
4 Double-click either OS X 10.2 and 10.3 Only or OS X 10.4 or higher
depending on your Mac OS version.
5 Double-click Kyocera OS X x.x.
Printing Operation
2-13
Download from Www.Somanuals.com. All Manuals Search And Download.
6 The printer driver installation program starts up.
7 Choose Select Destination, Installation Type and then install the
printer driver as directed by the instructions in the installation
software.
Note In addition to Easy Install, the Installation Type
options include Custom Install, which allows you to specify
the components to be installed.
IMPORTANT In the Authenticate screen, enter the name and
password used to log in to the operating system.
This completes the printer driver installation. Next, specify the print
settings.
If an IP or AppleTalk connection is used, the settings below are
required. If a USB connection is used, the printer is automatically
recognized and connected.
8 Open System Preferences and click Print & Fax.
9 Click the plus symbol (+) to add the installed printer driver.
2-14
PrintingOperation
Download from Www.Somanuals.com. All Manuals Search And Download.
10Click the IP icon for an IP connection or the AppleTalk icon for an
AppleTalk connection and then enter the IP address and printer
name.
11Select the installed printer driver and click Add.
12Select the options available for the printer and click Continue.
Printing Operation
2-15
Download from Www.Somanuals.com. All Manuals Search And Download.
13The selected printer is added. This completes the printer setup
procedure.
2-16
PrintingOperation
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing from Application Software
The steps required to print a document created with an application are
explained below. You can select the printing Paper Size and Output
Destination.
1 Load the paper required into the paper cassette.
2 From the application File menu, select Print. The Print dialog box
displays.
3 Click the drop down list of printer names. All the printers installed in
Windows are listed. Click the name of the machine.
4 Use Number of copies to enter the number of prints required. Up to
999 copies can be entered.
For Microsoft Word, we recommend that you click Options and
specify Use printer settings for the Default tray.
3
4
5 To start printing, click OK.
Note For information on how to use the printer driver software,
refer to KX Printer Driver User Guide.
Printing Operation
2-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Status Monitor
The Status Monitor monitors the printer status and provides an ongoing
reporting function. It also allows you to specify and modify settings for
printers not included in the KX driver.
The Status Monitor is installed automatically during KX driver installation.
Accessing the Status Monitor
Use either of the methods listed below to launch the Status Monitor.
• Launch when printing starts:
When you specify a printer and start a print job, one Status Monitor is
launched for each printer name. If Status Monitor startup is requested
from multiple printers, Status Monitors are launched for each printer
that issues the request.
• Launch from the KX driver properties:
Click the About button in the KX driver Properties dialog box. Then
click Status Monitor in the About dialog box to launch the Status
Monitor.
Exiting the Status Monitor
Use either of the methods listed below to exit the Status Monitor.
• Exit manually:
Right-click the Status Monitor icon in the taskbar and select Exit in the
menu to exit the Status Monitor.
• Exit automatically:
The Status Monitor automatically shuts down after 5 minutes if it is not
being used.
Screen Overview
The screen overview of the Status Monitor is as follows.
Pop-up window
3D View
Status Monitor icon
Pop-up window
If an information notification event occurs, a pop-up window appears. This
window only appears when the 3D View is open on the desktop.
2-18
PrintingOperation
Download from Www.Somanuals.com. All Manuals Search And Download.
3D View
This shows the status of the monitored printer as a 3D image. You can
choose whether to show or hide the 3D view from the menu displayed
when you right-click the Status Monitor icon.
If an information notification event occurs, the 3D view and an alert sound
are used to notify you. For information on the sound notification settings,
Status Monitor icon
While the Status Monitor is running, its icon is displayed in the taskbar
notification area. When you position the cursor over the icon, the printer
name appears. Right-clicking the Status Monitor icon allows you to set
the options below.
Show the status monitor
Displays or hides the Status Monitor icon.
Configure...
If the printer is connected to a TCP/IP network and has its own IP
address, use a web browser to access the COMMAND CENTER to
modify or confirm the network settings. For more information, refer to the
COMMAND CENTER Operation Guide.
Preferences...
Specify the Sound Notification and Appearance settings for the Status
Kyocera Online
Accesses the Kyocera Mita website.
Exit
Exits the Status Monitor.
Printing Operation
2-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Status Monitor Settings
Use the Preference option to set up the Status Monitor. The Status
Monitor has two tabs to configure its settings.
Sound Notification Tab
The Sound Notification tab contains the following items.
IMPORTANT To confirm the settings on Sound Notification tab, the
computer requirs the sound capabilities such as sound card and
speaker.
Enable Event Notification
Select to enable or disable monitoring the events in Available events.
Sound file
A sound file can be selected if you require an audible notification. Click
Browse to search for the sound file.
Use Text to speech
Select this check box to enter text you would like to hear played for
events. Although a sound file is unnecessary, this function is applicable
for Windows XP or later.
To use this function, follow these steps.
1 Select Enable Event Notification.
2 Select an event to use with the text to speech function in Available
events.
3 Click Browse to notify the event by sound file.
Note The available file format is WAV.
Select Use Text to speech to speech the text entered in Text to
speech box when an event occurred.
4 Click Play
to confirm the sound or text is played correctly.
2-20
PrintingOperation
Download from Www.Somanuals.com. All Manuals Search And Download.
Appearance Tab
The Appearance tab is contains the following items.
Enlarge window
Doubles the size of the Status Monitor window.
Always on top
Positions the Status Monitor in front of other active windows.
Transparency
Displays the Status Monitor as a transparent window.
Printing Operation
2-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Uninstalling Software (Windows PC)
The software can be uninstalled (removed) using the CD-ROM (Product
Library) supplied with the printer.
IMPORTANT On Macintosh computers, because the printer settings
are specified using a PPD (PostScript Printer Description) file, the
software cannot be uninstalled using the CD-ROM (Product Library).
1 Exit all active software applications.
2 Insert the enclosed CD-ROM (Product Library) into the CD-ROM
drive.
3 Following the procedure used to install the printer driver, click
Remove Software. The Kyocera Uninstaller wizard appears.
4 Select the software package to remove.
5 Click Uninstall.
Note In Windows Vista, the Remove Driver and Package
screen appears. Select Remove driver and driver package,
and click OK.
The uninstaller starts.
6 When Uninstall complete screen appears, click Next.
7 Select whether you restart your computer or not, click Finish.
2-22
PrintingOperation
Download from Www.Somanuals.com. All Manuals Search And Download.
General Information
This chapter describes basic maintenance tasks you can perform on the
printer. You can replace the following component according to the
printer’s display:
• Toner Kits
• Waste Toner Box
Also, the following parts need periodic cleaning:
• Paper Transfer Unit
Note Information Collection on Memory Chips - The memory
chip attached to the toner container is designed to improve
convenience for the end user; to support the recycling operation
of empty toner containers; and to gather information to support
new product planning and development. The information
gathered is anonymous - it cannot be associated to any specific
individual and the data is intended to be used anonymously.
Toner Container Replacement
The toner container in the printer should be replaced as soon as the
message display shows Toner lowor soon after. If you continue to use
the printer, eventually the toner supply will be exhausted at which point
the printer will stop printing and the Replace toner C,M,Y,Kmessage
will be shown instructing you to install a new toner kit.
Frequency of Toner Container Replacement
The life of the toner containers depends on the amount of toner required
to accomplish your printing jobs. According to ISO/IEC 19798 and
EcoPrint switched off the toner container can print as follows (A4/Letter
paper is assumed):
FS-C5100DN
Toner Color
Life of the Toner Container (Printable pages)
Black
5,000 images
4,000 images
4,000 images
4,000 images
Cyan
Magenta
Yellow
FS-C5200DN
Toner Color
Life of the Toner Container (Printable pages)
Black
7,000 images
6,000 images
6,000 images
6,000 images
Cyan
Magenta
Yellow
3-2
Maintenance
Download from Www.Somanuals.com. All Manuals Search And Download.
FS-C5300DN
Toner Color
Life of the Toner Container (Printable pages)
Black
12,000 images
10,000 images
10,000 images
10,000 images
Cyan
Magenta
Yellow
Note The toner container packed with the new printer has to fill
up the system when operating the first time. Therefore only 50%
of the first toner kits can be used for printing. (For example: FS-
C5200DN can print 3,500 monochrome images using the black
starter toner container).
Toner Kits
For best results, we recommend that you only use genuine Kyocera Parts
and Supplies.
The toner kits are supplied in 4 different colors: cyan, magenta, yellow
and black.
A new toner kit for each color contains the following items:
• Toner Container
• Plastic waste bags for old toner container and old waste toner box
• Waste Toner Box
• Installation Guide
Note Do not remove the toner container from the carton until you
are ready to install it in the printer.
Understanding Messages Requesting Toner Container
Replacement
The printer displays messages for individual colors at two stages of toner
usage. This message is automatically alternated with the other printer
message (such as Ready):
• When the printer becomes low on toner, for example in the cyan
container, the printer displays the message Toner low Cas the first
caution. Note the replacement is not always necessary at this stage.
• If you ignore the above message and continue printing, the printer
displays the message Replace toner— just before the toner is
used up. The toner container must be replaced immediately. Clean
the separate charger wires, etc. After the cleaning is finished,
however, the message does not automatically change to Ready. To
restart printing, you must press [GO] and make the printer ready.
Maintenance
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the Toner Container
This section explains how to replace the toner containers. When
replacing the toner container of any color, always replace the waste toner
box at the same time. If this box is full, the printer may be damaged or
contaminated by the waste toner that may spill over the box.
CAUTION Do not attempt to incinerate the Toner
Container. Dangerous sparks may cause burns.
IMPORTANT During toner container replacement, temporarily move
storage media and computer supplies (such as floppy disks) away
from the toner container. This is to avoid damaging media by the
magnetism of toner.
IMPORTANT Kyocera Mita Corporation is not liable against any
damages or problems arising from the use of toner containers other
than those designated as original Kyocera toner containers. For
optimum performance, it is also recommended to use only the
Kyocera toner containers which are specifically intended for use in
your country or region. If the toner container for another destinations
is installed, the printer will stop printing.
Note You do not have to turn printer power off before starting the
replacement. Any data that may be processing in the printer will
be deleted if you turn the printer power off.
To replace the toner container, first make sure of the color of the toner
container requiring replacement. In this example, it is assumed that you
are replacing the yellow toner container.
1 Open the top cover (top tray).
Top Cover
(Top Tray)
Magenta (M)
Cyan (C)
Yellow (Y)
Black (K)
2 Carefully remove the old toner container from the printer.
3-4
Maintenance
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Put the old toner container in the plastic bag (contained in the toner
kit) and discard it later according to the local code or regulations for
waste disposal.
Plastic Bag
4 Take the new toner container out of the toner kit.
5 Shake the new toner container 5 or 6 times as shown in the figure in
order to distribute the toner evenly inside the container.
Do not press too firmly on the center of the toner container or touch
the toner feed slot.
Toner Feed Slot
6 Set the new toner container in the printer as shown in the figure
below.
7 Push down on the top of the toner container to install it firmly in place.
Use the same procedure to replace the other color toner containers.
8
Close the top cover (top tray).
Note If the top cover (top tray) does not close, check that the
new toner container is installed correctly (in step 7).
After use, always dispose of the toner container and the
waste toner box in accordance with Federal, State and Local
rules and regulations.
Proceed to the next section.
Maintenance
3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the Waste Toner Box
Replace the waste toner box when the Check waste toner box
message is displayed. A new waste toner box is included with the toner
kit. The waste toner box needs to be replaced before the printer will
operate.
1 Open the left cover.
Left Cover
2 While holding the waste toner box, press the lock lever and then
gently remove the waste toner box.
Note Remove the waste toner box as gently as possible so
as not to scatter the toner inside. Do not let the opening of the
waste toner box face downward.
Lock Lever
3 Close the cap to the old waste toner box after removing the box from
the printer.
Cap
Old Waste
Toner Box
4 To prevent toner from spilling, put the old waste toner box in the
plastic bag (contained in the toner kit) and discard it later according
to the local code or regulations for waste disposal.
Plastic Bag
3-6
Maintenance
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Open the cap of the new waste toner box.
Cap
New Waste Toner Box
6 Insert the new waste toner box as shown in the figure. When the box
is set correctly, it will snap into place.
New Waste
Toner Box
7 Make sure that the waste toner box is correctly inserted and close the
left cover.
After replacing the toner containers and the waste toner box, clean the
paper transfer unit. For instructions, refer to Cleaning the Printer on page
3-8.
Maintenance
3-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning the Printer
The paper transfer unit should be cleaned each time the toner container
and waste toner box are replaced.
To maintain optimum print quality, it is also recommended that the inside
of the printer be cleaned once a month as well as when the toner
container is replaced.
It should also be cleaned if streaking or lines appear on printed copies, or
if printouts appear faint or blurred.
Cleaning the Paper Transfer Unit
Print problems such as soiling of the reverse side of printed pages may
occur if the paper transfer unit becomes dirty. To clean the paper transfer
unit, you must use the dry cloth.
1 Press the lever to release the lock.
2 Pull out the front cover.
3-8
Maintenance
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Wipe away the paper dust on the registration roller and the paper
ramp using the cleaning cloth.
Paper Transfer Unit
Duplex Unit
Cleaning Cloth
Paper Ramp
Transfer Belt
(Black)
Registration
Roller (Metal)
Transfer Roller
(Black)
Note Be careful not to touch the black transfer roller and
black transfer belt during cleaning as this may adversely
affect print quality.
4 Push the front cover back in completely.
Note Take care not to get your hands caught in the front
cover when you close it.
Maintenance
3-9
Download from Www.Somanuals.com. All Manuals Search And Download.
3-10
Maintenance
Download from Www.Somanuals.com. All Manuals Search And Download.
General Guidelines
The table below provides basic solutions for problems you may encounter
with the printer. We suggest you consult this table to troubleshoot the
problems before calling for service.
Symptom
Check Items
Corrective Action
Print quality is not good.
Paper is jammed.
Nothing lights on the operation panel
Check that the power cord is properly Turn off the printer’s power, plug in the
even when power is turned on and the plugged into the power outlet.
fan makes no noise.
power cord securely, and try turning on
the printer’s power again.
Check that the power switch is in the
On (|) position.
Set the power switch to the On
position.
The printer prints a status page, but
Check the printer cable or the interface Connect both ends of the printer cable
does not print jobs from the computer. cable.
securely. Try replacing the printer cable
or the interface cable.
Check program files and application
software.
Try printing another file or using
another print command. If the problem
occurs only with a specific file or
application, check the printer driver
settings for that application.
The printer is emitting steam in the
area around the top tray.
Check the room temperature to see if it Depending on the printing environment
is low, or if damp paper was used.
and the paper's condition, the heat
generated during printing will cause the
moisture in the paper to evaporate, and
the steam emitted may look like
smoke. This is not a problem, and you
can continue printing.
If the steam concerns you, raise the
room temperature, or replace the
paper with a newer, dryer paper.
Tips
Printer problems may be solved easily by following the tips below. When
you have encountered a problem that following the above guidelines will
not solve, try the following:
• Turn the printer power off and wait for several seconds. Then, turn on
the printer.
• Reboot the computer which sends the print jobs to the printer.
• Obtain and use the latest version of the printer driver. The latest
versions of printer drivers and utilities are available at:
• Make sure that the procedures for printing are correctly followed in the
application software. Consult the documentation supplied with the
application software.
4-2
Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
Print Quality Problems
The tables and diagrams in the following sections define print quality
problems and the corrective action you can conduct to solve the
problems. Some solutions may require cleaning or replacing parts of the
printer.
If the suggested corrective action will not solve the problem, call for
service.
Printed Results
Corrective Action
Skewed-color printout
Conduct color registration using the printer operation panel.
For details, refer to Registration Normal (Color registration [standard])
section or Registration Details (Color registration [detailed]) section of the
Advanced Operation Guide.
Completely blank printout
Full single-color printout
Dropouts or stray dots
Check the toner containers.
Open the printer top cover (top tray) and check that the toner containers
are correctly installed in the printer. For more information on installing the
Check that the application software is correctly operated.
Check the main charger unit.
Open the left cover and check that the main charger unit is correctly
installed.
Clean the main charger units.
For details, refer to LSU/Charger (LSU/Main charger cleaning mode
setting) section of the Advanced Operation Guide.
Troubleshooting
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Printed Results
Corrective Action
Black or white vertical streaks
Check the operation panel for toner.
If the Toner low C,M,Y,Kmessage is displayed with color description,
install a new toner kit for the color. To replace the toner container, refer to
Clean the main charger units.
For details, refer to LSU/Charger (LSU/Main charger cleaning mode
setting) section of the Advanced Operation Guide.
Direction
of Paper
Feed
Refresh drum.
Perform the following procedures on the operation panel and try cleaning
the drum surface using the printer's built-in cleaning system.
1
2
3
4
5
6
Press [MENU].
Press U or V repeatedly until Adjust/Maintenance>appears.
Press Z. Press U or V repeatedly until >Service >appears.
Press Z. Press U or V repeatedly until >>Drumappears.
Press [OK] twice.
The message display shows Please wait. After approx. 3 minutes,
the display returns to Ready.
Faint or blurred printing
Clean the main charger units.
For details, refer to LSU/Charger (LSU/Main charger cleaning mode
setting) section of the Advanced Operation Guide.
Make sure the paper type setting is correct the paper being used.
For details, refer to Paper Settings section of the Advanced Operation
Guide.
Conduct color calibration either by switching the printer off then on or using
the printer operation panel.
For details, refer to Color Calibration section of the Advanced Operation
Guide.
Try adjusting the color control settings using the printer driver.
Check the operation panel. If the Toner low C,M,Y,Kmessage is
displayed with color description, install a new toner kit for the color. To
Refresh drum.
Perform the following procedures on the operation panel and try cleaning
the drum surface using the printer's built-in cleaning system.
1
2
3
4
5
6
Press [MENU].
Press U or V repeatedly until Adjust/Maintenance>appears.
Press Z. Press U or V repeatedly until >Service >appears.
Press Z. Press U or V repeatedly until >>Drumappears.
Press [OK] twice.
The message display shows Please wait. After approx. 3 minutes,
the display returns to Ready.
4-4
Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
Printed Results
Corrective Action
Grey background
Clean the main charger units.
For details, refer to LSU/Charger (LSU/Main charger cleaning mode
setting) section of the Advanced Operation Guide.
Conduct color calibration either by switching the printer off then on or using
the printer operation panel.
For details, refer to Adjust/Maintenance (Adjust/Maintenance selection/
setting) section of the Advanced Operation Guide.
Dirt on the top edge or back of the paper Check the paper chute and the ramp.
Pull out the paper transfer unit and check for toner on the paper ramp.
Clean the paper ramp using a soft, dry, lint-free cloth. For details, refer to
Clean the main charger units.
For details, refer to LSU/Charger (LSU/Main charger cleaning mode
setting) section of the Advanced Operation Guide.
Troubleshooting
4-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Error Messages
The following table lists errors and maintenance messages that you can
be dealt with by yourself. If Call serviceappears, turn off the printer,
disconnect the power cord, and contact your service technician.
If Call serviceor Error.Power off.is displayed, turn off the printer
then turn it back on to see if the printer has recovered. If the printer has
not recovered, turn off the printer, disconnect the power cord, and contact
your service representative or authorized service center.
Some errors cause the alarm to sound. To stop the alarm, press [Cancel].
Message
Corrective Action
This message is displayed when the Job Accounting function is enabled and an attempt to
specify job accounting settings or to register or delete an account fails. To return the printer to
the print-ready status, press [GO].
Account error ##
Press GO
The paper has run out in the paper source displayed. Supply paper according to the paper
source displayed (paper cassettes, MP tray, or optional paper feeders).This message is
displayed alternately with messages indicating the printer status, such as, Ready, Please
wait, and Processing.
Add paper MPTray
F###represents a controller error (#=0, 1, 2, ...). Call for service. The printer does not
operate when this message is displayed.
Call service
F000F###:
####represents a mechanical error (#=0, 1, 2, ...). Call for service. The printer does not
operate when this message is displayed. The total number of pages printed is also indicated,
e.g. 0123456.
Call service
####:0123456
Displayed when data is being canceled.
Canceling data
The corresponding paper cassette is not installed. Install the cassette. The cassette number
can be 1 (topmost) to 4 (bottom).
Cassette #
not loaded
Displayed when the paper type does not match the envelope switch setting.
Change envelope
switch position
This message is displayed when a paper lift error has occurred in the paper source's
cassette. Pull out the cassette for the paper source displayed (either the paper cassettes or
optional paper feeders) and check if the paper is loaded correctly.
Check
cassette #
The message Call serviceis displayed when this error occurs repeatedly.
This message warns following two cases. Install the new waste toner box.
The waste toner box is not installed.
The waste toner box is full.
Check waste
toner box
This message will be displayed when replacing the toner container after the message
Replace toner Clean printeris displayed. After cleaning the inside of the printer,
press [GO] and the printer will be ready for printing.
Clean printer
Press GO
The front cover of the printer is open. Close the front cover.
Close
front cover
The left cover of the printer is open. Close the left cover.
Close
left cover
4-6
Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
Message
Corrective Action
The top cover of the printer is open. Close the printer top cover.
Close
top cover
This message is displayed when Remove Devicewas selected while a USB memory was
being used.
The previous screen is displayed again 1 or 2 seconds.
Device busy
You attempted to print with a paper size and paper type that cannot be used for duplex
printing. Press [GO] to print onto one-side of the paper only.
Duplex disabled
Press GO
An account code must be entered. This message is displayed if you try to print from the
operation panel (e.g. printing a status page or using the Job Retention function) when the Job
Accounting function is enabled. For more information, refer to Job Accounting (Job
Accounting selection/setting) section of the Advanced Operation Guide.
Enter Account
Displayed when the envelope switch is set to envelope mode.
Envelope mode
Turn the power switch off and then back on again. If this message still remains, turn the
power switch off, and contact your service representative or authorized service center.
Error.Power off.
F###
The printer controller and operation panel cannot exchange data. Turn the printer off and
unplug it from the mains power supply. Then contact your service representative or
authorized service center. See the back page of this manual for the relevant phone numbers.
Error.Power off.
F000
This message is displayed when the Job Accounting function is enabled and an attempt has
been made to exceed the print limit set for each account. To return the printer to the print-
ready status, press [GO].
Exceeded Max.out
Press GO
For more information, refer to Job Accounting (Job Accounting selection/setting) section of
the Advanced Operation Guide.
The specified file was not found on the hard disk, RAM disk or memory card. For more
information on the hard disk, RAM disk and memory cards, refer to Device Common
(Selecting/Setting the common device) section of the Advanced Operation Guide.
File not found
Press GO
The hard disk installed in the printer is not formatted, and therefore cannot be read or written.
Format error
Hard disk
The memory card inserted in the printer is not formatted, and therefore cannot be read or
written. To format a memory card, follow the procedure in Memory Card (Using the memory
card) section of the Advanced Operation Guide.
Format error
Memory card
A hard disk error has occurred. Look at the error code given in place of ##and refer to
Hard disk err ##
Press GO
The user ID entered for a private job is not correct. Check the user ID that you specified on
the printer driver. For more information, refer to Job Box section of the Advanced Operation
Guide.
ID error
This message is displayed when the Job Accounting function is enabled and no account is
set for a transmitted print job or the specified account is not registered (the incorrect account
is set). To return the printer to the print-ready status, press [GO].
Illegal Account
Press GO
For more information, refer to Job Accounting (Job Accounting selection/setting) section of
the Advanced Operation Guide.
Replace Maintenance Kit which is displayed on the message display. Replacement of the
maintenance kit is necessary at every 200,000 images of printing and requires professional
servicing. Contact your service technician.
Install MK
Troubleshooting
4-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Message
Corrective Action
Printing using the Job Box function failed because there was insufficient space available on
the hard disk or RAM disk, or because the RAM disk was disabled when demounting the hard
disk. To print an error report and return the printer to the print-ready status, press [GO].
Job not stored
Press GO
This message is displayed when printing was attempted, despite the Job Account function
being on with Restriction applied as the job limit for each job account.
To return the printer to the print-ready status, press [GO].
Job restricted
Press GO
For more information, refer to Job Accounting (Job Accounting selection/setting) section of
the Advanced Operation Guide.
Current print processing cannot continue because of occurrence of KPDL error which is
categorized by ##. To print out an error report, display >>Error Reportfrom the menu
system, and select On. Press [GO] to resume printing. You can abandon printing by pressing
[Cancel].
KPDL error ##
Press GO
If Auto Error Clear is set to On, printing will be automatically resumed after a preset period of
time.
The paper cassette matching the paper size and paper type of the print job is empty. Load
paper into the paper cassette as displayed in place of #. Press [GO] to resume printing.
If you want to print from a different paper source, press U or V to display Use
alternative? and you can change the source for paper feeding. After selecting a paper
source and pressing [MENU], Paper Settings >appears. By pressing the U, the paper
type settings menu appears. After setting the correct paper type, press [OK] and printing
starts.
Load Cassette #
(A4)/(PLAIN)
There is no paper cassette installed in the printer that matches the paper size and paper type
of the print job. Set paper in the MP tray. Press [GO] to resume printing. (Note that feeding
the paper having a paper size which does not match the current paper size from the MP tray
can cause paper jam.)
Load MP Tray
(A4)/(PLAIN)
If you want to print from a different paper source, press U or V to display Use
alternative? and you can change the source for paper feeding. After selecting a paper
source and pressing [MENU], Paper Settings >appears. By pressing the U, the paper
type settings menu appears. After setting the correct paper type, press [OK] and printing
starts.
This message is displayed when Lowwas selected in Security Level.
Low security
Memory overflow
Press GO
The total amount of data received by the printer exceeds the printer’s internal memory.
Try adding more memory. Press [GO] to resume printing. You can abandon printing by
pressing [Cancel].
If Auto Error Clear is set to On, printing will be automatically resumed after a preset period of
time.
A memory card error has occurred. Look at the error code given in place of ##and refer to
status, press [GO].
MemoryCard err##
Press GO
Multi copies cannot be printed because RAM disk is disabled or the hard disk is not installed.
Try adding more memory or installing hard disk, and configuring the RAM disk settings.
No multi copies
Press GO
This message is displayed when the optional paper feeder PF-510 is not connected to a
power source and COATED(coated paper) is selected as the paper type setting. Connect it to
a power source via the printer.
No power supply
Cassette
Displayed when the installed toner is the original Kyocera product.
Original toner
installed
4-8
Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
Message
Corrective Action
A paper jam has occurred. The location of the paper jam is indicated in place of the #’s. For
Paper jam
###############
The selected cassette is being prepared.
Paper loading
There is no paper cassette in the feeder, or the cassette is not inserted properly. After
reinserting the paper cassette, you should be able to print. When two or more optional
feeders are installed and the lowest one is selected, the same message will appear if any of
the upper paper feeder and the printer cassette is improperly installed.
Paper path error
The data transferred to the printer was too complex to print on a page. Press [GO] to resume
printing.
Print overrun
Press GO
A RAM disk error has occurred. Look at the error code given in place of ##and refer to
RAM disk error##
Press GO
Two message items are displayed alternately. Toner has run out in the toner container(s).
Replace the toner container using a new toner kit for the particular color. The printer does not
operate when this message is displayed.
Replace toner
C,M,Y,K
For example, if Replace toner C,Kis displayed, replace the cyan and the black toner
containers.
Replace toner
Clean printer
Replace the toner container using a new toner kit. Color of the toner container that needs to
be replaced is represented by C(Cyan), M(Magenta), Y(Yellow), and K(Black).
Toner low
C,M,Y,K
The top tray has become full (approx. 250 pages). You must remove all printed pages from
the top tray. When the printer detects that the top tray is empty again, the printer will
continues printing into the top tray.
Top tray
paper full
Displayed when the installed toner is not the original Kyocera product. Install original Kyocera
toner.
Unknown toner
installed
This message is displayed if the installed toner container's regional specification does not
match the printer's.
Install the specified toner container.
Unknown toner PC
C,M,Y,K
An error has occurred in the USB memory device. To return the printer to the print-ready
status, press [GO].
USB memory err##
Press GO
When the cassette does not contain any paper that matches the print data (paper size and
type), this message allows you to specify an alternative cassette to use instead. A paper
source number is only displayed when an optional paper feeder is installed. To print from a
different paper source, refer to Paper Feed Mode (Setting the paper feed source) section of
the Advanced Operation Guide.
Use alternative?
Cassette 1
Displayed when an attempt is made to register an account in the Job Accounting menu by
entering an account code that already exists.
Wrong Account
For more information, refer to Job Accounting (Job Accounting selection/setting) section of
the Advanced Operation Guide.
Troubleshooting
4-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Message
Corrective Action
• The ID or Password entered for the Job Accounting function is not correct. Check the ID or
Password.
Wrong ID
For more information, refer to Job Accounting (Job Accounting selection/setting) section of
the Advanced Operation Guide.
• The user ID entered for a private job, or a stored job is not correct. Check the user ID that
you specified on the printer driver.
The password does not match the password set. Enter the correct password. For more
information, refer to Job Accounting (Job Accounting selection/setting) section of the
Advanced Operation Guide.
Wrong Password
Storage Error Codes
Hard Disk Errors
Code
Meaning
01
Hard disk format error. If this error recurs even if the power has been turned
off and then on, reformat the hard disk.
02
04
The disk system is not installed. Recheck the requirements for using the
system and the devices.
There is no available hard disk space. Delete unnecessary files, etc., in order
to free up space.
05
06
The specified file does not exist in the hard disk.
There is no memory available to the hard disk system. Increase the available
memory.
10
97
Formatting is not possible because host data is being spooled on the hard
disk. Wait until the hard disk is ready, and then format.
The number of permanent code jobs that can be stored reached the limit
value, and no more can be saved. Either delete some unnecessary jobs, etc.,
or increase the limit.
98
99
An unreadable page was found in a job (The job is damaged.).
A print job for the specified ID does not exist in the hard disk.
4-10
Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
Memory Card and USB Memory Errors
Meaning
Code
01
The printer does not support the memory card inserted, or the memory card
is broken. Insert the correct memory card.
For more information, refer to Memory Card (Using the memory card) section
of the Advanced Operation Guide.
02
The memory card is not installed. Recheck the requirements for using the
system and the memory card.
03
04
The memory card is write protected. Check the memory card's status.
There is not enough space in the memory card. Delete unnecessary files or
use a new memory card.
05
06
The specified file is not on the memory card or the USB memory.
There is not enough printer memory to support the memory card system.
Increase printer memory.
50
The memory card is write protected, or invalid. Check the memory card's
status.
RAM Disk Errors
Meaning
Code
01
02
04
05
06
Format error. Try turning the power off and on again.
RAM disk mode is Off. Turn RAM disk mode Onfrom the operation panel.
No disk space. Purge unnecessary files.
Specified file is not on disk.
Insufficient printer memory to support the RAM disk system. Expand printer
memory.
Troubleshooting
4-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Clearing Paper Jams
If the paper jammed in the paper transport system, or no paper sheets
were fed at all, the Paper jammessage appears and the location of the
paper jam (the component where the paper jam has occurred) is also
indicated. The printer automatically goes off-line when this message is
displayed. Remove jammed paper. After removing jammed paper, the
printer will re-start printing.
Possible Paper Jam Locations
The figure below explains the printer’s paper paths including the options.
The locations where paper jams might occur are also shown here, with
each location explained in the table below. Paper jams can occur in more
than one component on the paper paths.
MP Tray
Paper Cassette
Paper Feeder
PF-500, PF-510
(Only2stackedpaperfeederscan
be used with the FS-C5100DN)
Paper Jam Message
Description
Reference Page
Paper is jammed inside the printer,
paper cassette or MP tray.
Paper jam
Printer
Paper is jammed at the optional paper
feeder’s cassette.
Paper jam
Cassette 2 (to 4)
4-12
Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
General Considerations for Clearing Jams
Bear in mind the following considerations when attempting jam removal:
CAUTION When pulling the paper, pull it gently so as not to
tear it. Torn pieces of paper are difficult to remove and may
be easily overlooked, deterring the jam recovery.
• If paper jams occur frequently, try using a different type of paper,
replace the paper with paper from another ream, flip the paper stack
over, or rotate the paper stack 180 degrees. The printer may have
problems if paper jams recur after the paper was replaced.
• Whether or not the jammed pages are reproduced normally after
printing is resumed depends on the location of the paper jam.
Utilizing Online Help Messages
Online help messages are available in the printer’s message display to
provide simple instructions for clearing jams. Press ( ) when the paper
jam message has appeared. Then a help message will appear to facilitate
jam clearing in the location.
Paper jam at Cassette
Paper is jammed at paper cassette.
1 First, open the printer's front cover and check for paper jams in the
paper transfer unit.
2 Pull out the paper cassette and remove the jammed paper.
Paper Jam at MP Tray
Paper is jammed at the MP tray. Remove the jammed paper using the
procedure given below.
1 First, open the printer's front cover and check for paper jams in the
paper transfer unit.
2 Remove the jammed paper.
Troubleshooting
4-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Paper Jam in Printer
Paper is jammed at the paper cassette or inside the printer. Remove the
jammed paper using the procedure given below.
CAUTION Components inside the fuser cover are hot. Do not touch
it with your hands as it may result in burn injury.
1 Press the lever to release the lock.
2 Pull the front cover towards you.
3 If the paper has jammed near the registration roller, as shown in A,
A
remove the paper by pulling it up from the center.
Registration
Roller
If the paper has jammed inside the fuser unit, as shown in B, open
the fuser cover and remove the paper by pulling its edge.
B
Fuser
Cover
4-14
Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
If the paper has jammed inside the duplex unit, as shown in C, lift the
duplex unit and remove the paper by holding it in the middle.
C
Duplex Unit
4 Close the front cover.
Paper Jam at Cassette 2 (to 4)
Paper is jammed at the paper cassette. Remove the jammed paper using
the procedure given below.
Pull out the paper feeder and remove the jammed paper.
Troubleshooting
4-15
Download from Www.Somanuals.com. All Manuals Search And Download.
4-16
Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Specifications
Note Specifications are subject to change without notice.
Description
FS-C5100DN
Item
FS-C5200DN
FS-C5300DN
Printing
Method
Electrophotographic four color (CMYK) printing using tandem (4) drum system
Printing
Speeds
Cassette
MP Tray
A4: 21 ppm, B5, A5, A6: 23 ppm*1, Letter: 23 ppm,
Legal: 17 ppm
A4: 26 ppm, B5, A5,
A6: 28 ppm*1, Letter: 28 ppm,
Legal: 22 ppm
A4: 19 ppm, B5, A5, A6: 20 ppm*1, Letter: 20 ppm,
Legal: 17 ppm
A4: 23 ppm, B5, A5,
A6: 24 ppm*1, Letter: 24 ppm,
Legal: 20 ppm
Duplex Printing Speed
A4: 11 ppm, B5, A5: 11 ppm*2, Letter: 11 ppm,
Legal: 8 ppm
A4: 26 ppm, B5, A5: 28
ppm*1, Letter: 28 ppm, Legal:
11 ppm
Resolution
600 dpi
First Print Out Time
B/W : 10.5 seconds or less
Color : 12 seconds or less
(Sleep: 35 seconds or less)
B/W : 9 seconds or less
Color : 10.5 seconds or less
(Sleep: 35 seconds or less)
Warm-upTime Power On
(23°C,
44 seconds or less
25 seconds or less
36 seconds or less
30 seconds or less
60%RH)
Sleep
(within 3 hours)
Controller
Memory
PowerPC440-533 MHz
256 MB
PowerPC440-667 MHz
Standard
Maximum
1280 MB
Operating Systems
Microsoft Windows 2000/XP/Vista, Windows Server 2003
Apple Macintosh OS X
Interface
Standard
USB: Hi-Speed USB
Network: 10 BASE-T/100 BASE-TX
KUIO-LV slot
Option
-
Hard Disk
Memory Card Slot
Monthly Duty Average
Maximum
1 (Compact Flash, 4 GB or less)
1,500 pages
2,000 pages
3,000 pages
50,000 pages
65,000 pages
100,000 pages
*1 : After 16 pages the printing speed becomes 14 ppm.
*2 : After 16 pages the printing speed becomes 7 ppm.
Specifications
5-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Description
FS-C5100DN
Item
FS-C5200DN
FS-C5300DN
Paper Sizes
Cassette
A4, B5, A5, Folio, 8 1/2 × 14"(Legal), 8 1/2 × 11"(Letter), Oficio II, Statement, Executive,
ISO B5, A6, Envelope C5, 16K, and Custom
Cassette
(Optional
Paper Feeder
PF-500/
Envelope Monarch, Envelope #10, Envelope #9, Envelope #6, Envelope DL, Envelope
C5, A5, B5, ISO B5, A4, Executive, Letter, Legal, OufukuHagaki, Oficio II, Statement,
Folio, Youkei 2, Youkei 4, 16K, and Custom
PF-510)
MP Tray
A4, B5, A5, Folio, 8 1/2 × 14"(Legal), 8 1/2 × 11"(Letter), Oficio II, Statement, Executive,
A6, B6, ISO B5, Env. Monarch, Envelope #10, Envelope #9, Envelope #6, Envelope DL,
Envelope C5, 16K, Hagaki, OufukuHagaki, Youkei 2, Youkei 4, and Custom
Paper Types† Cassette
(Optional
Plain, preprinted, bond, recycled, rough, letterhead, color, prepunched, high quality, and
custom
Paper Feeder
PF-500)
Cassette
Plain, preprinted, labels, bond, recycled, rough, letterhead, color, prepunched, envelope,
cardstock, coated, thick, high quality, and custom
(Optional
Paper Feeder
PF-510)
MP Tray
Plain, transparency, preprinted, labels, bond, recycled, vellum, rough, letterhead, color,
prepunched, envelope, cardstock, coated, thick, high quality, and custom
Paper Feed
Source
Capacity
Cassette
MP Tray
250 sheets (80 g/m2)
500 sheets (80 g/m2)
150 sheets (80 g/m2)
150 sheets (80 g/m2)
Margin
4 mm (left, right, top and bottom)
250 sheets (80 g/m2)
Output Tray
Capacity
Top Tray
Operation
Temperature 10 to 32.5 °C (50 to 90.5 °F)
Environment
Relative
Humidity
15 to 80 %
Altitude
2,500 m (8,202 feet) maximum
Illumination 1,500 lux maximum
120 V, 60 Hz, max. 9.2 A (U.S.A./Canada) 220-240 V, 50 Hz/60 Hz, max. 4.7 A (European
Power Source
countries) Max. allowable voltage fluctuation: ±10 % Max. allowable frequency fluctuation:
±2 %
Power
Consumption
Maximum
1,231 W or less
405 W
1,221 W or less
420 W
1,233 W or less
477 W
During
Printing
During
Standby
69 W
7 W
70 W
7 W
79 W
7 W
During
Sleep Mode
Power Off
0 W
0 W
0 W
5-2
Specifications
Download from Www.Somanuals.com. All Manuals Search And Download.
Description
Item
FS-C5100DN
FS-C5200DN
FS-C5300DN
Operating
Noise††
During
Printing
LpA = 53 dB (A)
During
LpA = 36 dB (A)
Standby
During
immeasurably low
Sleep Mode
Dimensions (W x D x H)
345 × 518 × 455 mm
345 × 518 × 480 mm
13-5/8 × 18-1/2 × 17-9/10"
13-5/8 × 20-2/5 × 18-9/10"
Weight
Approx. 28 kg (61 lbs)
Approx. 29 kg (64 lbs)
Approx. 29.5 kg (65 lbs)
†. When using CUSTOM 1(to 8), use the MP tray for paper sizes smaller than 105 × 148 mm (4 1/8 × 5 13/16
inches). The MP tray can be used with paper sizes over 70 × 138 mm (2 3/4 × 5 7/16 inches).
††. Sound pressure level at bystander position [front] in accordance with EN ISO 7779.
Specifications
5-3
Download from Www.Somanuals.com. All Manuals Search And Download.
5-4
Specifications
Download from Www.Somanuals.com. All Manuals Search And Download.
We recommend the use of our own brand supplies.
We will not be liable for any damage caused by the use of third party supplies in this machine.
A1
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
2008
is a trademark of Kyocera Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Rev. 1.2 2009.8
Download from Www.Somanuals.com. All Manuals Search And Download.
Printed in China 302HN56012
|