KEYS 800 TREADMILL
OWNER’S MANUAL
Proudly made in the USA by:
KEYS Fitness Products, LP
P.O. Box 551239
Dallas, Texas 75239
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Information
NING!
1) WARNING: Before using this treadmill or starting any exercise program, consult your physician. This is
especially important for persons over the age of 35 and/or persons with pre-existing health problems. The
manufacturer or distributor assumes no responsibility for personal injury or property damage sustained by or through
the use of this product.
2) WARNING: To reduce the risk of electrical shock, burns, fire, or other possible injuries to the user, it is important
to review this manual and the following precautions before operation.
SAFETY PRECAUTIONS AND TIPS
„
It is the owner’s responsibility to ensure that all users of this treadmill have read the Owner’s Manual and are familiar
with warnings and safety precautions.
„
„
This treadmill has a user maximum capacity of 275 pounds.
The treadmill should only be used on a level surface and is intended for indoor use only. The treadmill should not
be placed in a garage, patio, or near water and should never be used while you are wet. Keys Fitness recommends
a treadmill mat be placed under the treadmill to protect floor or carpet and for easier cleaning.
„
„
Follow safety information in regards to plugging in your treadmill. Keep the power cord away from the incline wheels
and do not run the power cord underneath your treadmill. Do not operate the treadmill with a damaged or frayed
power cord.
Wear comfortable, good-quality walking or running shoes and appropriate clothing. Do not use the treadmill with
bare feet, sandals, socks or stockings.
„
„
„
„
„
„
„
„
„
„
Always straddle the belt and allow it to start moving before stepping onto the belt.
Hold on to handrails when adjusting speed, incline, or other controls.
Always examine your treadmill before using to ensure all parts are in working order.
Allow the belt to fully stop before dismounting.
Pets should be never be allowed near or on the treadmill.
Do not leave children unsupervised near or on the treadmill.
Never operate the treadmill where oxygen is being administered, or where aerosol products are being used.
Never insert any object or body parts into any opening.
For safety and to prevent damage to your treadmill, no more than one person should use the treadmill at a time.
Always unplug the treadmill before cleaning and/or servicing. Service to your treadmill should only be performed by
an authorized service representative, unless authorized and/or instructed by the manufacturer. Failure to follow
these instructions will void the treadmill warranty.
„
Never leave the treadmill unattended while it is running.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Start
Thank you for purchasing a KEYS treadmill! This quality product you have chosen was
designed to meets your needs for cardiovascular exercise.
• Before you start, please read the Owner’s Manual and become familiar with the
operation of your new treadmill.
• Remember to take the time to perform the stretching exercises
provided to avoid injury.
• Do not stand on the walking belt while pressing the Power button or Start/Stop button.
• Always adjust the speed of the treadmill in small increments as this treadmill is capable
of high speeds.
• If you are taking medication, consult your physician to see if the medication will affect
your exercise heart rate.
• If you have heart problems, you are not active, and/or are over the age of 50 years, do
not use the pre-set treadmill programs or start an exercise program without first
contacting and receiving approval from your physician.
• To avoid the risk of electrical shock, always keep the console dry. Do not spill liquids
on the console. KEYS recommends a sealed water bottle for beverages consumed
while using the treadmill.
• Please review the following drawing below to familiarize yourself with the listed
parts. This manual covers several treadmills, so the one pictured below may not
be identical to your particular model.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Warm Up Exercises
NING!
WARM UP FIRST !
Warming up prepares the body for exercise by increasing circulation, supplying more
oxygen to the muscles and raising body temperature. Begin each workout with 5 to 10
minutes of stretching and light exercise to warm up. The drawings on this page show
several forms of basic stretching you may perform before your workouts. Again, consult a
physician before starting this or any other exercise program.
15 Seconds for each
20 Seconds
20 Seconds
20 Seconds
30 Seconds
20 Seconds
20 Seconds
25 Seconds
30 Seconds
25 Seconds each leg
20 Seconds
5 Seconds X 3 times
25 Seconds each leg
5 Times
15 Seconds
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly Instructions
Assembly
KEYS treadmills are shipped in one piece to make assembly easy. After opening the box, remove
any packing materials from the treadmill. Do not throw away any packing materials until the unit
is working properly. Place the base on a clean, level surface. Make sure the electrical cord will
easily reach an electrical outlet.
1) Have a second person raise the console to the upright position and hold.
2) Insert the TUBE SPACER inside the upright frame and line up with the bottom hole. Hold tube
spacer while inserting the 1 1/2” Button Head Bolt and lightly tighten. Repeat for opposite side.
3) After completing opposite side, TIGHTEN ALL FOUR BOLTS SECURELY. Assembly is now
complete.
4) Be sure to use the RED SAFETY KEY before turning the power on.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Power Requirements
WARNING!
IMPROPER CONNECTION OF THE EQUIPMENT GROUNDING CONNECTOR CAN RESULT
IN A RISK OF AN ELECTRIC SHOCK. CHECK WITH A QUALIFIED ELECTRICIAN OR
SERVICE MAN IF YOU ARE IN DOUBT AS TO WHETHER THE PRODUCT IS PROPERLY
GROUNDED. DO NOT MODIFY THE PLUG PROVIDED WITH THE PRODUCT, IF IT WILL
NOT FIT THE OUTLET, HAVE A PROPER OUTLET INSTALLED BY A QUALIFIED
ELECTRICIAN.
This treadmill can be seriously damaged by sudden voltage changes in your home’s electrical power. Voltage
spikes, surges, and noise interference can result from weather conditions or from other appliances being turned on or
off. To reduce the possibility of treadmill damage, always use a surge protector (not included) with your treadmill.
Surge protectors can be purchased at most hardware stores. Keys Fitness recommends a single outlet surge
protector with a UL 1449 rating as a Transient Voltage Surge Suppressor (TVSS) with a UL suppressed voltage
rating of 400V or less and an electrical rating of 120VAC, 15 amps.
This treadmill must be grounded to reduce the risk of electrical shock. Grounding provides a path of least resistance
for electric current, should the treadmill malfunction. This treadmill comes with an electrical cord having an
equipment-grounding conductor and a grounding plug. Always plug the power cord into a surge protector, and plug
the surge protector into an appropriate outlet that is properly installed and grounded in accordance with all local
codes and ordinances.
This product is for use on a nominal 120-volt circuit, and has a grounding plug that looks like the plug illustrated in the
drawing (1) below.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Console Functions and Descriptions
There are five display windows on the control panel to provide feedback information.
TIME WINDOW
•
TIME: Indicates elapsed time after pressing start in minutes and seconds (0-99 minutes, 0-59
seconds)
•
INTERVAL TIME: Indicates countdown in seconds to the next interval starting at 5 seconds and
counting to 0 seconds
SPEED WINDOW
•
SPEED: Indicates MPH up to 10MPH (miles per hour) or KMH (kilometer per hour) in .1 increments
DISTANCE / CALORIES WINDOW
•
DISTANCE: Indicates Miles or Kilometers traveled in .01 increments up to 9.99 and .1 increments
starting at 10.0
•
CALORIES: Indicates estimated calories used based on 150 lb. person at the indicated speed,
incline, and time
INCLINE WINDOW
•
INCLINE: Indicates incline in percent of grade 0-12% in 1 increments
CENTER BRICKYARD WINDOW
•
Displays quarter mile track in Manual mode. Indicates position on track by a blink. In program
mode, shows the change in speed profile across the interval range (1-10) and shows position with a
blinking action.
•
The treadmill console will display the name of the program selected, showing on the left hand side of
the window. The LAP counter will appear in manual mode in the center of the window.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Program and Operating Instructions
QUICK START / MANUAL MODE
•
•
•
•
Plug into a standard wall outlet (110-Volt AC, 15-amp circuit).
Attach RED Safety Key to treadmill console.
Stand on the treadmill and straddle belt.
Press POWER button. There will be an eight (8) second delay after pressing the POWER
button before data can be entered. The TIME window will flash.
•
Press START/STOP button. Belt will begin to move after 4 seconds. Step on belt slowly after
the belt starts moving. Speed or incline may be adjusted by using the appropriate + (increase)
or – (decrease) buttons.
•
•
•
To end your workout, press START/STOP button. Belt will gradually slow to zero.
To pause your workout, press PAUSE.
To re-start after pausing: Press the PAUSE button. WARNING: The treadmill belt will
resume at the speed the treadmill was moving before pausing.
•
Countdown Time, Preset Speed and/or Incline: Time, Speed, and Incline may be preset
prior to getting started. After pressing the POWER button, the time window will blink. Use the
SPEED/TIME + or – arrows to select your workout time, then press the ENTER PROGRAM
button. The SPEED/TIME window will now be flashing. Using the same + or – arrows, select
the speed for your workout, then press ENTER PROGRAM. Now the INCLINE window will be
flashing. Use the INCLINE + or – arrows to set your workout incline, then press ENTER
PROGRAM. To start, press the START/STOP button.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Program and Operating Instructions
PROGRAM MODE
•
•
•
•
Plug into a standard wall outlet (110-Volt AC, 15-amp circuit).
Attach RED Safety Key to treadmill console.
Stand on the treadmill and straddle belt.
Press POWER button. There will be an eight (8) second delay after pressing the POWER
button before data can be entered. The TIME window will flash.
•
There are three (3) pre-set programs on the Keys 800, Fat Burn, Cardio, and Warm Up
programs (see the program profiles later in this manual). Select the program by pressing the
appropriate button.
•
•
•
Press START/STOP button. Belt will begin to move after 4 seconds. Step on belt slowly after
the belt starts moving.
Each of the pre-set programs can also be customized. Follow the instructions below for
your particular model.
Customizing programs in P1 and P2 Mode: Each pre-set program can be customized in the
P1 or P2 mode. After making the program selection, the center window will read “OP.” ”OP”
refers to “original program” and is preset. Press the same program button once more, and the
center window will read P1. The “P1” mode is now accessed. You can now program the
Time, Speed, and Incline in P1 mode, which will save your entered information for future use.
The time window will blink. Use the SPEED/TIME + or – arrows to select your workout time,
then press the ENTER PROGRAM button. The SPEED/TIME window will now be flashing.
Using the same + or – arrows, select the speed for your workout, then press ENTER
PROGRAM. Now the INCLINE window will be flashing. Use the INCLINE + or – arrows to set
your workout incline, then press ENTER PROGRAM. To start, press the START/STOP
button. To access P2 mode, press the selected program button three times (once for OP,
twice for P1, three times for P2). Follow the above procedure to customize.
•
TO CHANGE A PREVIOUSLY PROGRAMMED P1, P2, or user program: Once you have
programmed the P1 or P2 modes, you will need to use the PAUSE button to change the
program you previously entered. For instance, if P1 in Fat Burn has been programmed, to
change to a new setting, press the Fat Burn button twice to access P1. Then press the
PAUSE button to get the TIME window to flash. Follow the directions above to continue to
change the program.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Program Profiles
The FAT BURN program is designed to vary
treadmill elevation while maintaining a constant
walking speed. Set the desired maximum speed
and incline, and the treadmill will automatically
change the incline to the set amount, alternating
in segments 2-3, 5-6, and 8-9.
The CARDIO program is designed to vary
treadmill speed while maintaining a constant
incline. Set the desired maximum speed and
incline, and the treadmill will automatically
change the speed to the set amount, alternating
in each segment.
EACH PROGRAM HAS 10 SEGMENTS. THE LENGTH
OF TIME FOR EACH SEGMENT IS BASED ON THE
TIME LENGTH OF THE PROGRAM. IF YOU SET THE
PROGRAM TO 30 MINUTES, EACH SEGMENT IS 3
MINUTES LONG (TIME divided by 10 SEGMENTS).
The WARM UP program is designed to gradually increase
treadmill speed and incline (warm up) in the first segment
to the set maximum speed and incline. The program will
then plateau at the set speed and incline maximums. At
the end of the program, the treadmill will gradually
decrease speed and incline to half of the maximum set
(cool down) in segments 9-10.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Belt Adjustment and Tension
WARNING! Do not overtighten rollers! This will cause premature roller bearing failure!
Belt adjustment and tension performs two functions: adjustment for tension and centering. Your
new treadmill comes pre-adjusted from the factory for tension and centering. Please follow the
procedures below if the belt shifts left or right or if the belt slips while walking:
WALKING BELT HAS SHIFTING TO THE LEFT (Diagram 1)
First, unplug the power cord from the surge protector. Using the hex key provided, turn the left
rear roller adjustment bolt ¼ turn in the clockwise direction. Plug the power cord back into the
surge protector and run the treadmill at 2.5 mph. You should see the belt start to correct itself,
moving back towards the center. Repeat the above procedure until the walking belt is centered.
It may be necessary to set walking belt tension once you have completed this procedure if the belt
feels like it is slipping while walking. Refer to below to the “Walking Belt Slipping” instructions.
WALKING BELT HAS SHIFTING TO THE RIGHT (Diagram
2)
First, unplug the power cord from the surge protector. Using
the hex key provided, turn the right rear roller adjustment bolt
¼ turn in the clockwise direction. Plug the power cord back
into the surge protector and run the treadmill at 2.5 mph. You
should see the belt start to correct itself, moving back towards
the center. Repeat the above procedure until the walking belt
is centered. It may be necessary to set walking belt tension
once you have completed this procedure if the belt feels like it
is slipping while walking. Refer to below to the “Walking Belt
Slipping” instructions.
WALKING BELT IS SLIPPING DURING USE (Diagram 3)
First, unplug the power cord from the surge protector. Using
the hex key provided, turn both left and right rear roller
adjustment bolts the same distance, usually a ¼ turn in the
clockwise direction. Plug the power cord back into the surge
protector and run the treadmill at 2.5 mph. You should now
walk on the belt to determine if the belt is still slipping. Repeat
the above procedure until the walking belt is not slipping. The
tension should be just tight enough not to slip.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Change Miles per hour to Kilometers per hour
Your treadmill will operate in British Units (miles per hour) or International Units (kilometers per
hour). All treadmills are calibrated at the factory for British Units (miles per hour). To change the
display to read in kilometers, follow the steps described here:
1)Power is turned OFF on the console. Attach the magnet safety key to the console.
2) Activate the calibration mode switch by inserting the eraser end of a pencil into the opening in
the backside of the console (see diagram below).
3) Depressing the calibration mode switch TWICE and CL21 should appear in the TIME window.
(On the Keys 800, ‘mph or kph’ will be flashing in the SPEED window)
4) Pressing the the SPEED +/- button will activate choice, then press “ENTER PROGRAM.”
5) To accept the setting, press the POWER button.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance Instructions
WARNING! Before performing any maintenance to your treadmill, always unplug
the power cord from the surge protector.
CLEANING
Routine cleaning of your Keys Fitness treadmill will extend the life of your treadmill. WARNING! To prevent electrical
shock, be sure the power to the treadmill is OFF and the unit unplugged from the wall electrical outlet before
attempting any cleaning or maintenance.
AFTER EACH WORKOUT: Wipe off the console and other treadmill surfaces with a clean, water dampened soft
cloth to remove excess perspiration. USE NO CHEMICALS.
WEEKLY: Use of a treadmill mat is recommended for ease of cleaning. Dirt from your shoes contacts the belt and
eventually makes it to underneath the treadmill. Vacuum underneath treadmill once a week.
DECK LUBRICATION
The treadmill deck and belt have been pre-lubricated at the factory. However, it is recommended that the walking
board be checked periodically for lubrication to ensure optimal treadmill performance.
Every 30 days or 30 hours of operation, lift the sides of the walking belt and feel the top surface of the walking board
as far under as you can reach. If you feel signs of silicone, no further lubrication is required. If it feels dry to the
touch, follow the instructions below.
Please use Lube ‘N Walk or silicone spray such as Napa 8300. (Ask your treadmill dealer or call us)
TO APPLY LUBRICANT TO THE WALKING BOARD
1) Position the walking belt so that the seam is located on top and in the center of the center of the walking board.
2) Insert the spray nozzle into the spray head of the lubricant can.
3) While lifting the side of the walking belt, position the spray nozzle between the walking belt and the board
approximately 6” from the front of the treadmill. Apply the silicone spray to the walking board, moving from the front
of the treadmill to the rear. Repeat this on the other side of the belt. Spray approximately 4 seconds on each side.
4) Allow the silicone to ‘set’ for one minute before using the treadmill.
WARNING: Do not overlubricate the walking board. Excess lubricant should be wiped off with a clean towel.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Guide
Treadmill will not start.
1) Is the RED Safety Key Attached to the Console?
2) Make sure the power cord is plugged into a surge protector, the surge protector is plugged into a
properly grounded outlet, and the surge protector is turned on. (Refer to “Power Requirements”)
3) Check the circuit breaker located on the front of the treadmill. If the switch protrudes, it has tripped.
Wait five minutes and then press the switch back in.
4) Check the house electrical breaker box and the circuit breaker for the room the treadmill is located in.
If it has tripped, reset or have an electrician replace the breaker in home.
5) Have an electrician check for inadequate voltage at the outlet.
Treadmill looses power during use.
1) Check the circuit breaker located on the front of the treadmill. If the switch protrudes, it has tripped.
Wait five minutes and then press the switch back in.
2) Check the house electrical breaker box and the circuit breaker for the room the treadmill is located in.
If it has tripped, reset or have an electrician replace the breaker in home.
3) If treadmill still will not operate, please call Keys Technical Service at (888) 340-0482.
Treadmill walking belt slows during use.
1) Check to make sure the treadmill is securely plugged into an UL-listed surge protector, rated at 15
amps, with a 14-guage cord of five feet or less and the surge protector is securely plugged into the
outlet.
2) If treadmill still will not operate, please call Keys Technical Service at (888) 340-0482.
Treadmill walking belt slips or is not centered on rear roller.
1) Refer to “Belt Adjustment and Tension” section.
2) Need help? Call Keys Technical Service at (888) 340-0482.
Treadmill Error Messages.
2)Your treadmill is equipped with a software package that enables error messages to be displayed when
there is a problem. To avoid possible damage to the treadmill and the possibility of injury, do not
operate the treadmill until the problem is corrected. Call Keys Technical Service at (888) 340-
0482.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List - KEYS 800 Treadmill
KEY #
1
PART #
DESCRIPTION
UPRIGHT ASSEMBLY D. GRY
DECK ASSEMBLY D GRY
FRONT ELEVATION ASSEMBLY
MOTOR MOUNTING BRACKET
MOTOR COVER BRACKET
BELT GUIDE
QTY
1
KEY #
53
58
67
68
69
70
PART #
08-0004
14-0069
02-0004
02-0005
02-0006
02-0007
02-0008
02-0009
02-0013
02-0014
02-0016
02-0020
02-0021
02-0022
02-0024
02-0028
DESCRIPTION
CIRCUIT BREAKER 15 AMP
END CAP DECAL
QTY
1
23-0064
23-0063
23-0050
19-0014
19-0015
19-0019
06-0089
05-0007
06-0080
06-0005
06-0105
06-0008
10-0002
10-0003
08-0077
12-0022
1
2
2
1
SCREW, 8X 5/8 PHIL PH
SCREW, 8X 5/8 PHIL PH HILO
BOLT, 5/16 X 5 - 1/2 SHOULDER BOLT
5/16-18 NYLOCK NUT
29
12
1
3
1
7
7
8
2
3
10
13
16
22
25
26
27
34
35
36
37
BASE PAN MOTOR
1
71
72
76
77
79
83
84
85
87
SCREW, 5/16-18 X 3/4 HEX
NUT, 5/16-18 WHIZLOC
3
SIDE BOARD EXTRUSION
FAN 5" 8mm bore
2
3
1
LOCK WASHER, 1/4
8
DOME PLUG
4
SCREW, 1/4-20 X 2 - 1/2 HEX
SCREW, 3/8-16 X 2 - 1/2 HEX
SCREW, 1/4-20 X 2-1/2 SOCKET HEAD
WASHER, 9/32 X 5/8 X 1/8
NUT, 10-24 NYLOCK
10
1
MOTOR COVER
1
END CAP
1
2
BOARD ISOLATOR
8
3
FOAM GRIP
2
4
FERRITE CORE
1
CARRIAGE BOLT 5/16 X 1
2
ACTUATOR (ELEVATION MOTOR)
1
MAGNETIC KILL SWITCH SAFETY KEY
RED
1
DRIVE MOTOR
1
1
1
1
1
1
1
1
1
1
1
1
94
99
SCREW, 3/8-16 X 1 3/4 HEX
1
2
38
39
40
41
42
42
43
44
45
48
49
50
12-0023
03-0003
04-0008
04-0004
06-0003
09-0012
09-0013
13-0011
13-0003
13-0016
13-0007
24-0111
02-0031
02-0036
02-0038
06-0024
WALKING BOARD
SCREW, GREEN HEAD 8 X 5/8 PPH
HEX WRENCH 3/16 NOT SHOWN
WALKING BELT 18" X 105"
POLY V BELT
101
1
HEX WRENCH PLASTIC CLIP (not shown)
1
PULLEY vx0086 8 GR
FRONT ROLLER (with 06-0003 pulley)
REAR ROLLER
1
104
105
107
108
109
EMERGENCY STOP DECAL
BUSHING, STRAIN RELIEF
WIRE TIES NOT SHOWN
1
14-0027
06-0014
06-0016
06-0021
06-0022
1
POWER CORD
10
5
ENCODER HARNESS
CONTROL PANEL HARNESS
BREAKER WIRE 6" NOT SHOWN
WIRE CLAMP NOT SHOWN
RESET GUIDE TUBE NOT SHOWN
1
CONSOLE ASSEMBLY 5 WIN LCD (not
shown)
MOTOR CONTROLLER
1
1
51
52
08-0014
08-0047
OPTICAL ENCODER
16
Download from Www.Somanuals.com. All Manuals Search And Download.
KEYS 800 Treadmill KEYS FITNESS PRODUCTS, LP – LIMITED WARRANTY
PLEASE CONSULT YOUR PHYSICIAN BEFORE USING THIS PRODUCT.
This Limited Warranty applies in the United States, Canada, and Mexico to products manufactured or distributed by Keys Fitness Products, LP (“Keys”)
under the KEYS brand name. The warranty period to the original purchaser is (lifetime) on the frame, (3) years on the motor, (2) years on parts, and (1) year labor.
Keys warrants that the Product you have purchased for non-commercial, personal, family, or household use from Keys or from an authorized Keys reseller
is free from defects in materials or workmanship under normal use during the warranty period. Your sales receipt, showing the date of purchase of the Product, is your
proof of the date of purchase. This warranty only extends to you, the original purchaser. It is not transferable to anyone who subsequently purchases the Product from
you. It excludes expendable parts. This Limited Warranty becomes VALID ONLY if the treadmill is assembled/installed by a Keys Fitness authorized dealer/technician
unless otherwise authorized by Keys Fitness in writing (if anyone other than a Keys Fitness authorized dealer/technician assembles a Keys Fitness treadmill the
warranty will be void unless accompanied by written authorization by Keys Fitness).
During the warranty period Keys will at no additional charge, repair or replace (at Keys’ option) the product if it becomes defective, malfunctions, or
otherwise fails to conform with this Limited Warranty under normal non-commercial, personal, family or household use. In repairing the Product, Keys may replace
defective parts, or at the option of Keys, serviceable used parts that are equivalent to new parts in performance. All exchanged parts and Products replaced under this
warranty will become the property of Keys. Keys reserves the right to change manufacturers of any part to cover any existing warranty.
To obtain warranty service, you must contact a Keys authorized service technician or Keys Fitness at our phone numbers located in this manual. Any parts
determined to be defective must be returned to Keys to obtain warranty service. You must prepay any shipping charges, export taxes, custom duties and taxes, or any
other charges associated with transportation of the parts or Product. In addition, you are responsible for insuring any parts or Product shipped or returned. You
assume the risk of loss during shipment. You must present Keys with proof-of-purchase documents (including the date of purchase). Any evidence of alteration,
erasing or forgery of proof-of-purchase documents will be cause to void this Limited Warranty.
This warranty does not extend to any product not purchased from Keys or from an authorized Keys reseller. This Limited Warranty does not extend to any
Product that has been damaged or rendered defective; (a) as a result of accident, misuse, or abuse; (b) by the use of parts not manufactured or sold by Keys; (c) by
modification of the Product or normal wear and tear; (d) operation on incorrect power supplies; or (e) as a result of service by anyone other than Keys, or an authorized
Keys warranty service provider. Product on which the serial number has been defaced or removed is not eligible for warranty service. Should any Product be
submitted for warranty service be found ineligible therefore, an estimate of repair cost will furnished and the repair will be made if requested by you upon Keys’ receipt
of payment or acceptable arrangements for payment.
EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, KEYS MAKES NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. KEYS EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS
LIMITED WARRANTY. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS LIMITED WARRANTY. NEITHER KEYS
NOR ANY OF ITS AFFILIATES SHALL BE RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW
LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR
EXCLUSION MAY NOT APPLY TO YOU. This Limited Warranty gives you specific legal rights and you may also have other rights that may vary from state to state. This
is the only express warranty applicable to Keys-branded products. Keys neither assumes nor authorizes anyone to assume for it any other express warranty.
PLEASE SEND IN THE ATTACHED WARRANTY CARD WITHIN TEN (10) DAYS OF PURCHASE TO REGISTER YOUR
TREADMILL WITH KEYS FITNESS PRODUCTS, LP. MADE IN THE USA.
Thank you for your business! PLEASE MAIL WARRANTY CARD TO:
KEYS FITNESS PRODUCTS, PO BOX 551239, DALLAS, TX 75355.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
|