Specifications
Format System .................................................................... Compact disc digital audio system
Laser
............................................................................................ Semiconductor laser
Audio
Frequency response ....................................................................... 20 Hz to 20 kHz, 3 dB
PHONE output level (32 Ω, 1kHz) ................................................................ 7 mW + 7 mW
Line output/impedance ................................................................................ 0.6 Vrms/22 kΩ
PORTABLE CD PLAYER
Power supply
External DC supply (AC-45060A) ......................................................................... DC 4.5 V
Commercially-available alkaline batteries (LR03) x 2 or 4 ...................... 1.5V x 2 (or 4)
Rechargeable batteries (NB-3A70) x 2 or 4 ............................................... 1.2V x 2 (or 4)
Battery life (Fully charge)
DPC-X347
INSTRUCTION MANUAL
CD-DA
Commercially-available alkaline
batteries
Approx. 7 Hours
X
2
Commercially-available alkaline
batteries
CAUTION: (Except for Europe)
÷ THIS UNIT IS DESIGNED ONLY FOR LR03 ALKALINE
BATTERY OPERATION AND NO RECHARGEABLE BAT-
Approx. 16 Hours
Approx. 4.5 Hours
X
4
Rechargeable batteries
X
2
TERIES AND AC ADAPTORS SHOULD BE USED.
÷ Common accessories available in general electrical stores
may cause damage and fire to your unit, in such event the
Kenwood Product Liabilities will be exempted.
Rechargeable batteries
X
2 and
Approx. 11.5 Hours
Commercially-available alkaline
batteries
X
2
÷ At 0.1mW+0.1mW output (32Ω load).
÷ Standard value during continuous use/charging in an temperature of 20.
÷Time of use may vary depending on battery maker, battery type, use environment,
and temperatute.
÷ The unit may not operate normally if manganese batteries are used.
Dimensions (W x H x D) ...................... 138 mm x 21.5 mm x 138 mm (5- 7/16" x 7/8" x 5- 7/16")
Weight (net)
..........................................................................................................185 g (6.5 oz)
Note:
KENWOOD follows a policy of continuous advancements in development. For this reason speci-
fications may be changed without notice.
Accessories
Unpacking
For Europe
: AC adaptor(1), Remote control (1), Headphones(1)
For other countries : Remote control (1), Headphones(1)
Unpack the unit carefully and make sure that all the accessories are present.
If any accessories are missing, or if the unit is damaged or fails to operate, notify your
dealer immediately. If the unit was shipped to you directly, notify your shipper
immediately. Kenwood recommends that you retain the original carton and packing
materials in case you need to move or ship the unit in the future.
Keep this manual handy for future reference.
Separately sold option part
Rechargeable Nickel Metal Hydride Battery ......................................................... NB-3A70
For your records
Record the serial number, found on the back of the
unit, in the spaces designated on the warranty card,
and in the space provided below. Refer to the model
and serial numbers whenever you call upon your
dealer for information or service on this product.
B60-5508-08 00 (E, Y)
0402
AP
Model
Serial Number
Maintenance
7Care of lens
Storage
When the lens in the pick-up gets dirty, malfunctions including the impos-
sibility of playback may occur. The lens should be cleaned using a commer-
cially available camera lens blower, etc. Do not touch the lens to prevent
damaging the mechanism. Also do not use a lens cleaner or disc cleaner
product.
When a disc is not to be played for a long period of time, remove it from the
CD player and store it in its case.
7Caution on condensation
Condensation (of dew) may occur inside the unit when there is a great
difference in temperature between this unit and the outside.
This unit may not function properly if condensation occurs. In this case,
leave the unit for a few hours and restart the operation after the conden-
sation has dried up.
Be specially cautious against condensation in the following circumstances:
When this unit is carried from one place to another across a large difference
in temperature, when the humidity in the room where this unit is installed
increases, etc.
7Care of main unit
When the unit gets dirty, clean with a soft, dry cloth. If the unit is stained
seriously, a moistened cloth can be used. Do not use thinner, benzine,
alcohol, etc. for these agents may cause discoloration.
7Cleaning the plug
Wipe the headphone plug with a soft cloth to keep it clean.
A dirty plug may cause noise or malfunction.
7Caution on disc used
Usable discs:
This unit is capable of playing back the Audio CD discs, CD-R/CD-RW (CD-DA)
discs and discs carrying the
marking. Other discs cannot be played.
8 cm single CDs can be played as they are; do not use a commercially-
available single CD adapter.
÷ Certain CD-R/CD-RW (CD-DA) discs may not be played due to
recording conditions of the discs.
Handling:
Hold compact discs so that you do not touch the playing surface.
Do not attach paper or tape to either the playing side or the label side of
compact discs.
Never play a cracked or warped disc:
During playback, the disc rotates at high speed in the player. Therefore, to
avoid danger, never use a cracked or deformed disc or a disc repaired with
tape or adhesive agent.
Cleaning
If fingerprints or foreign matter become attached
to the disc, lightly wipe the disc with a soft cotton
cloth (or similar) from the center of the disc
outwards in a radial manner.
Download from Www.Somanuals.com. All Manuals Search And Download.
Part names
Power sources
Using the AC adaptor (For Europe)
CAUTION
Unit
1
Å
Use the enclosed AC adaptor (AC-45060A) for this product.
ı
Ç
Ó
To the DC IN 4.5V
(External power) jack
Î
Ì
Ï
AC power
outlet
DC IN 4.5V
‰
¬
Å
PHONE(Phones/Remote)jacks
Ï OPEN switch
AC power
adaptor
ı LINE OUT jack
Ç VOL (Volume) knob
Î DBBS switch
‰ 7 (Stop/Off) key
38(Play/Pause) key
Slide to open top cover
Ì HOLD switch
Ó DC IN 4.5V (External power) jack
¬ Batteries case
Rechargeable battery operation (For Europe)
2
Note:
Rechargeable batteries are not provided with this unit. Always use the
separately sold rechargeable batteries NB-3A70. Rechargeable bat-
tery models other than the NB-3A70 may be unable to be recharged.
Remote control
The keys on the remote control unit with the same names as on the main unit
have the same function as the keys on the main unit.
7Loading the batteries
1 Open the battery cover.
2 Insert 2 or 4 rechargeable batteries and close the cover.
Å
ı
Ç
MODE PROG
VOL
Ì
Ï
‰
Î
÷ Make sure the positive (+) and negative (-) poles are properly aligned.
÷ When using two batteries, these can be loaded in either battery case.
÷ During battery charging or use of the unit, the battery may become warm.
This is normal and does not indicate a malfunction.
7Charging the rechargeable batteries
Å HOLD switch
ı 38(Play/Pause) key
4,¢keys
Î VOL (Volume) knob
‰ Display
Ï MODE key/ PROG key
Ì Clip
1 Plug in the AC adaptor.
2 Press and hold the 7 key more than 1 seconds. (Main unit only)
3 After the batteries have been charged, remove the AC adaptor.
7 (Stop/Off) key
Ç Headphones jack
÷ When using a rechargeable battery which is new or which has not been
used for more than 2 months, the operating period may be shorter than
normal. This is due to the properties of the battery and not a malfunction.
After recharging, use the battery on the unit until it is exhausted. The
original performance of the battery can be recovered by repeating this
cycle a few times.
÷ Makesuretoclosethetopcoveroftheunitbeforeproceedingtorecharging.
÷ Make sure that no alkaline batteries are loaded in the battery cases before
charging the rechargeable batteries.
Display (Remote control)
Å
ı
Ç
Î
‰
÷
Recharging completes in about 10 hours. Do not attempt to recharge the
batteries after this period.
1ALL HOLDASP
DBBS
PROG
INTRO
RAND
÷ Rechargeable batteries can be recharged. When the playable time per
recharge reduces, please newly purchase the optional (NB-3A70) recharge-
able batteries.
Ó
Ì
Ï
Å DBBS indicator
ı Repeat mode indicator
Ç HOLD indicator
Ï Playing time indicator
Ì Track number indicator
Ó PROGindicator,INTROindicator,
RAND indicator,
Î ASP indicator
‰ Battery duration indicator
Download from Www.Somanuals.com. All Manuals Search And Download.
When operating the unit with alkaline batteries 3
Note:
Playback from the first track
5
Alkaline batteries are not provided with this unit.
PHONE(Phones/ Remote) jacks
1 Open the battery cover.
2 Insert 2 or 4 alkaline batteries and close the cover.
VOL
DBBS
7/ 38
HOLD
OPEN
÷ Make sure the positive (+) and negative (-) poles are properly aligned.
÷ When using two batteries, these can be loaded in either battery case.
÷ Use commercially available LR03 batteries. The unit may not operate
normally if manganese batteries are used.
HOLD
÷ Replace 2 or 4 batteries at the same time.
MODE PROG
VOL
When operating the unit with 2 rechargeable batteries and 2
alkaline batteries
4
38/7/4/¢
VOL +/
-
1 Slide the OPEN switch in the direction of the arrow to open the top cover.
2 Insert disc and close the top cover.
CAUTION
Do not load one rechargeable and one alkaline batteries together in
the same battery case. Otherwise, battery burst or fluid leak may
cause a fire, injury or damage to the battery case and its surroundings.
÷ Insert with labeled side up.
÷ Secure the disc by pushing a position near the center hole unit it
clicks.
÷ Close securely by pushing the front center position of the top
cover unit it clicks.
This unit can be operated with 2 rechargeable batteries and 2 alkaline batteries.
3 Set the HOLD switch to off.
÷ When 4 batteries are used, make sure they are arranged so that batteries of the
same type are in line horizontally (see illustration).
÷ Always use the separately sold rechargeable battery NB-3A70.
÷ Exchange the same type of batteries at the same time.
÷ For the Hold function, read "Hold function".
÷ Before any operation, be sure to set the HOLD switch to off.
4 Press the 38key.
÷ The power comes on and playback begins.
÷ Certain CD-R/CD-RW (CD-DA) discs may not be played due to
recording conditions of the discs.
÷ The ASP function is activated permanently.
ASP display
ASP
Rechargeable batteries (NB-3A70)
Alkaline batteries
Track number
Elapsed time of track
being played
ASP (Anti Skip Protection) :
The audio signals of a certain period is stored in memory so that, even when
the signal from the optical pickup is interrupted by an external shock, this
unit can continue music without interruption.
Battery duration indicator
The duration at which the battery indicator starts to blink is variable
depending on the type of battery used.
5 Use the VOL knob to adjust the volume.
¶Rechargeable batteries
When the batteries is nearly exhausted:
]In a while, the power will be turned off automatically. Then
recharge the batteries.
7To pause playback temporarily
Press the 38key during playback states.
÷ Pressing the key again resumes playback.
¶ Alkaline batteries
When the batteries are half exhausted
7To stop playback
:
Press the 7key during playback states.
÷ The total number of tracks and the total playing time of them will
be displayed.
]Playback is possible while the indicator is blinking.
Battery duration indicator
7To turn power off
After stopping playback, press the 7key again.
Auto power-off function
If no operation key has been pressed for 30 seconds while the unit is in the
stop mode, the power is turned off automatically to prevent battery power
consumption.
7Skipping tracks
Press the 4or ¢ key.
÷ When the ¢ key is pressed, playback will skip to the start of the
subsequent track.
÷ Each time the key is pressed, playback will skip to the next track.
÷ When the 4key is pressed, playback will skip to the start of the
track being played back.
÷ Each time the key is pressed, playback will skip to the previous track.
Download from Www.Somanuals.com. All Manuals Search And Download.
7Fast forward, fast reverse
Program playback 7
Favorite tracks (max. 20 tracks) can be programmed.
38/7
Hold the 4 key or ¢key pressed during playback.
÷ Fast forward is engaged by pressing and holding down key ¢
while playback is in progress.
÷ Fast reverse is engaged by pressing and holding down key 4
while playback is in progress.
÷ Playback will resume when either key is released.
MODE PROG
VOL
Hold function
PROG
Slide the HOLD switch in the direction of the arrow to switch the HOLD
function on.
1 Press the PROG key during stop status.
÷ When the HOLD switch on the unit is switched on, the unit's keys cannot be
operated.
÷ Stop status is engaged when the 7 key is pressed while playback
is in progress.
÷ When the HOLD switch on the remote control is switched on, the remote
control's keys cannot be operated.
2 Use the 4 or ¢key to select the track, and press the PROG key.
ASP
Changing the tone
PROG
The low frequencies sound, which is felt in headphone, can be boosted.
Slide the DBBS switch to select the desired setting :
DBBS on position:
Low frequencies are boosted.
DBBS off position:
Track number
Programmed order
÷ Repeat step 2 to select other tracks in the order you want to program them.
÷ Up to 20 tracks can be programmed in this unit.
3 Press the 38key.
Normal tone reproduction.
÷ As a result, the audio may be distorted if the volume level is too high in a
section dominated by bass sound. In this case, set DBBS to off or decrease
the volume.
7To clear the programmed contents
Press the 7 key.
÷ The "PROG" indicator is turned off when the program is cleared. How-
ever, the programmed contents are stored.
÷ Program mode can be canceled when the 7 key is pressed or the top
cover is open while stop status is engaged. The programmed contents
are cleared.
Selecting Play Mode
6
38
MODE PROG
VOL
MODE
Press the MODE key for the following selections. (Press the playback status
or stop status.)
1 One-track repeat ("
" lights up)
1
The track being played or the selected track will be played repeatedly.
÷ To play the next track repeatedly, press the 4 or ¢ key.
2 All-track repeat ("
ALL" lights up)
All tracks on the disc will be played repeatedly.
3 Intro Scan ("INTRO" lights up)
The first 10 seconds of all tracks on the disc will be played in the recorded
order.
4 Random playback ("RAND" lights up)
All tracks on the disc will be played in a random order.
5 Normal playback
÷ If Intro Scan or Random Playback is selected while playback is in
progress, Intro Scan or Random Play operation will commence
when the track being played back is over.
÷ If Intro Scan or Random Play is selected during stop, Intro Scan or
Random play will start when the 38 key is pressed.
÷ The program of tracks is also valid in Repeat or Intro Scan playback.
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections 8
In case of difficulty
Ensure that the power of all components is off before connecting the cords.
What seems to be a serious trouble may sometimes be due to a simple
mistake. Before calling for service, check the items shown in the following
table again. (If you request servicing due to the reasons shown in the table, the
service may be charged in some cases.)
Speakers with
built-in amplifier
Amplifer
Pressing a key cannot initiate an operation or turn the unit on.
¶ The HOLD switch of the main unit or remote control is set to ON.
]Set the switch to off.
¶ The batteries are exhausted.
]Replace the 2 or 4 alkaline batteries, or recharge the rechargeable
batteries.
¶ The disc is placed upside down.
]Place the disc with the labeled side up.
¶ Condensation has occurred inside the unit.
]Leave the unit for about 1 hour before re-use.
¶ The AC adaptor is disconnected.
]Connect it properly.
No sound is heard from the headphones.
¶ The headphones are connected incompletely.
]Insert the plug securely into the PHONE jack.
¶ The headphones are connected to LINE OUT jack
]Insert the plug securely into the PHONE jack.
¶ The volume is set to the minimum position on the unit.
]Adjust the volume on the unit.
To LINE OUT jack
LINE OUT
Sound skips, or is interrupted.
¶ A strong vibration that exceeds the capacity of the ASP has occurred.
]Place the unit in a place not subject to vibration.
¶ The disc is dirty.
Note:
]Clean it.
÷ Adjust the listening volume on the connected audio component.
÷ The DBBS function should be set to off. (The tone should be adjusted only
on the connected audio component.)
¶ The headphone plug is dirty.
]Clean it.
Noise interferes
¶ The headphone plug is dirty.
]Clean it.
¶ The batteries are low.
]Replace or recharge the batteries.
¶ The headphones are connected incompletely.
]Insert the plug securely into the PHONE jack.
¶ A source of strong magnetism or radio wave, such as a TV set or cellular
phone, is present near the unit.
]Install the unit away from a TV set, cellular phone, etc.
Rechargeable batteries cannot be recharged.
¶ Commercially available rechargeable batteries are used.
]Use the exclusive rechargeable batteries (NB-3A70).
Note:
1. This system uses a microcomputer so it may malfunction due to external
noise or interference. In such a case, unplug the power cord and remove the
batteries, then re-connect the power cord and insert the batteries again.
2. Erroneous operation may occur when the headphone plug is plugged or
unplugged; but this is not a malfunction.
Download from Www.Somanuals.com. All Manuals Search And Download.
|