GPS NAVIGATION SYSTEM
INSTALLATION MANUAL
KNA-G520
B54-4501-08
Warning
Failure to avoid the following potentially hazardous situations could result in serious injury or fire.
• Do not attempt to install or service the KNA-G520 by yourself. Installing or servicing the unit without training and experience in
electronic equipment and automotive accessories may be dangerous and could expose you to the risk of electric shock or other hazards.
• When extending ignition, battery, or ground wires, use automotive-grade wires or other wires with AWG 18 (0.75 mm2 gauge) or
greater to prevent wire deterioration and damage to the wire coating.
• If the unit starts to emit smoke or strange smells, turn off the power immediately and consult your Kenwood dealer.
• Keep small articles (like screws or batteries) out of the reach of children. If any such object is accidentally swallowed, consult a doctor
immediately.
Caution
Failure to avoid the following potentially hazardous situations may result in injury or property damage.
• Make sure to ground the unit to the chassis of your vehicle.
• Secure all wiring with cable clamps or electrical tape. Insulate unconnected wires; do not allow any bare wiring to remain exposed.
• Do not let unconnected wires or terminals touch metal on the vehicle or anything else that can conduct electricity.
• Do not open the top or bottom covers of the unit.
• The KNA-G520 is not waterproof.
February 2006
Part Number 190-00493-50 Rev. A
Printed in Taiwan
Download from Www.Somanuals.com. All Manuals Search And Download.
- 3 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Acquiring GPS Signals
The first time you turn on the KNA-G520, you must wait while the system acquires satellite signals for the first time. This process
could take up to several minutes. Make sure your vehicle is outdoors in an open area away from tall buildings and trees for fastest
acquisition. After the system acquires satellites for the first time, it will acquire satellites quickly each time thereafter.
Changing the Fuses
If you need to replace a fuse on the red or yellow wires, make sure the wires are not touching to prevent a short circuit. Then replace
the old fuse with a new 2 Amp fuse.
Caution
When replacing a fuse, use only a new fuse with the prescribed rating. Using a fuse with the wrong rating may cause your unit to
malfunction. Disconnect the wiring harness before replacing a fuse to prevent short circuits.
Specifications
General
Operating Temperature: -15°C to 70°C
Storage Temperature: -40°C to 85°C
Operating Voltage:
9.5 V to 25 V
Current Consumption: 0.12 A typical at 13 V (Max 1.0 A at 13 V)
ACC off Current:
Dimensions:
Weight:
70 uA typical at 13 V
30 mm H x 120 mm W x 117 mm L
184 g
Mounting Orientation: Horizontal +/- 5 degrees
Map Storage:
Connectors:
Internal non-removable memory (pre-loaded City Navigator™ map data) and optional removable SD card
System/power, GPS antenna, SD card slot, Mini-B for optional FM traffic receiver
Navigation
Receiver:
12 parallel channel GPS receiver
1,575.42 MHz
Frequency:
Acquisition Times:
Warm:
Approx. 15 seconds
Cold:
Approx. 45 seconds
AutoLocate®:
Update Rate:
GPS Accuracy:
Approx. 2 minutes
1/second, continuous
15 meters (49 feet) RMS 95% typical with GPS
DGPS (WAAS) Accuracy: < 3 meters (10 ft) 95% typical with DGPS (WAAS) corrections
Antenna: External GPS antenna
- 4 -
Download from Www.Somanuals.com. All Manuals Search And Download.
GPS NAVIGATION SYSTEM
MANUEL D’INSTALLATION
KNA-G520
Avertissement
Si vous ne prenez pas les précautions suivantes, vous risquez de subir de graves blessures ou de provoquer un incendie.
• Ne tentez pas d’installer ou de réparer vous-même le KNA-G520. Si vous installez ou réparez l’unité sans avoir d’expérience dans le
domaine des équipements électroniques et des accessoires automobiles, vous vous exposez à un risque de choc électrique et à d’autres
dangers.
• Lorsque vous rallongez les câbles de contact, de batterie ou de terre, utilisez des câbles spécifiques pour automobiles ou d’autres câbles
d’un calibre de 0,75 mm2 (AWG 18) ou plus, afin d’empêcher toute détérioration du câble ou de son revêtement.
• Si l’appareil émet de la fumée ou une odeur bizarre, mettez immédiatement l’appareil hors tension et consultez un revendeur Kenwood.
• Tenez toujours les petits objets (comme les vis ou les batteries) hors de la portée des enfants. En cas d’ingestion de ces objets,
contactez immédiatement un médecin.
Attention
Si vous ne prenez pas de précautions pour éviter les situations potentiellement dangereuses suivantes, celles-ci sont susceptibles de
causer des blessures ou des dommages.
• Assurez-vous de relier l’unité à la terre via une alimentation électrique négative 12 Vcc.
• Maintenez en place tous les câbles à l’aide de colliers ou de ruban isolant. Isolez les câbles non connectés ; ne laissez aucun câble nu
exposé.
• Ne mettez pas de câbles ou d’attaches d’extrémité non reliés en contact avec des parties métalliques du véhicule ou tout autre élément
conducteur d’électricité.
• N’ouvrez pas le couvercle supérieur ou inférieur de l’appareil.
• Le KNA-G520 n’est pas étanche.
- 5 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Eléments inclus
antenne GPS
unité principale
vis (4)
faisceau de
câbles
fermetures
autoagrippantes (2)
Installation de l’unité principale
Utilisez les vis ou les fermetures autoagrippantes (semblables à du Velcro®) incluses afin d’installer l’unité principale dans le
véhicule. Sélectionnez un emplacement permettant d’accéder au logement de cartes SD de l’unité. Assurez-vous de placer l’unité
bien horizontalement (à plat) et de bien la fixer en place afin de permettre un fonctionnement optimal.
Attention
• N’installez pas l’unité à un emplacement exposé à la lumière directe du soleil, à une chaleur ou à une humidité excessive, et maintenez-
la à l’abri de la poussière et de tout liquide. Utilisez exclusivement les vis fournies. L’utilisation de vis non adéquates risquerait
d’endommager l’unité.
• Contrôlez la présence éventuelle de câbles ou d’autres pièces sous le tapis de sol avant de le découper.
Installation de l’antenne GPS
Attention
• Ne pas peindre l’antenne pour ne pas détériorer ou empêcher la réception des signaux.
• Enlevez tout objet ou amas de neige etc. du sommet de l’antenne pour ne pas réduire la réception.
• Ne tirez pas le câble pendant la dépose de l’antenne ou le réglage de sa position pour ne pas provoquer un court-circuit ou à casser le
câble.
L’antenne GPS peut être installée à l’intérieur ou à l’extérieur du véhicule. Elle doit être installée horizontalement pour optimiser
la réception GPS. L’antenne GPS doit avoir un accès dégagé au ciel. Si vous installez l’antenne à l’intérieur du véhicule, placez-la
près d’une fenêtre ; les signaux GPS traversent le verre mais pas le métal. Reportez-vous à l’illustration sur la page suivante pour
avoir un aperçu des emplacements recommandés pour l’installation de l’antenne. Placez l’antenne GPS sur une surface métallique,
comme le toit de votre véhicule, pour obtenir une réception optimale.
Installation des accessoires optionnels
Pour plus d’informations sur l’installation du récepteur FM d’informations sur le trafic (comme le GTM 10), reportez-vous au guide
d’installation du récepteur concerné.
Configuration de la fonction Paramétrage Estime
La fonction Paramétrage Estime permet au système de navigation de continuer à fournir des indications de navigation même
lorsqu’il ne reçoit plus de signal GPS. Après avoir connecté le câble rose et avoir démarré le système de navigation, vous devez
configurer la fonction Paramétrage Estime pour qu’elle fonctionne correctement. Dans la page Menu du système de navigation,
touchez Réglage > Navigation > Paramétrage Estime > Réglage.
Type d’onde Odomètre — sélectionnez Onde carrée ou Onde sinusoïdale. Déterminez le paramètre adapté en contactant le
fabricant du véhicule ou en utilisant un oscilloscope. Les ondes carrées sont les plus répandues.
Polarité du feu de recul — sélectionnez Haute ou Bas. Contactez le fabricant du véhicule pour connaître le type de polarité ou
effectuez la vérification au moyen d’un voltmètre. Choisissez Haute (cas le plus fréquent) si une tension positive élevée est détectée
lors de l’allumage des feux de marche arrière. Choisissez Bas si aucune tension ou une tension basse est détectée lors de l’allumage
des feux de marche arrière.
- 6 -
Download from Www.Somanuals.com. All Manuals Search And Download.
- 7 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Acquisition de signaux GPS
Lorsque vous allumez le KNA-G520 pour la première fois, vous devez attendre que le système acquière des signaux satellites.
Cette opération peut prendre plusieurs minutes. Assurez-vous que votre véhicule se trouve en extérieur dans une zone dégagée
dépourvue de bâtiments élevés ou d’arbres afin de faciliter l’acquisition. Une fois que le système a acquis les signaux satellites pour
la première fois, cette acquisition se fait plus rapidement à chaque utilisation ultérieure.
Changement des fusibles
Si vous devez remplacer un fusible au niveau des câbles rouge ou jaune, assurez-vous que ceux-ci n’entrent pas en contact, afin
d’éviter un court-circuit. Remplacez ensuite le fusible usagé par un nouveau fusible de 2 ampères.
Attention
Lors du remplacement d’un fusible, utilisez uniquement un nouveau fusible présentant les caractéristiques recommandées. L’utilisation
d’un fusible présentant des caractéristiques différentes risque d’entraîner un dysfonctionnement de votre unité. Déconnectez le faisceau
de câbles avant de remplacer un fusible, afin d’éviter tout court-circuit.
Spécifications
Généralités
Température de fonctionnement : de -15°C à 70°C
Température de stockage :
Tension de fonctionnement :
Consommation courante :
Courant alternatif hors courant :
Dimensions :
de -40°C à 85°C
de 9,5 V à 25 V
en général de 0,12 A sous 13 V (max. 1 A sous 13 V)
en général 70 µA sous 13 V
30 mm H x 120 mm l x 117 mm L
184 g
Poids :
Orientation de montage :
Stockage des cartes :
horizontale +/- 5 degrés
mémoire interne non amovible (données cartographiques City Navigator™ préchargées) et carte SD
amovible facultative.
Connecteurs :
système/alimentation, antenne GPS, logement de carte SD, Mini-B pour récepteur FM
d’informations sur le trafic optionnel.
Navigation
Récepteur :
récepteur GPS 12 canaux parallèles
1 575,42 MHz
Fréquence :
Durées d’acquisition :
Chaud :
environ 15 secondes
Froid :
environ 45 secondes
AutoLocate®:
environ 2 minutes
Fréquence de mise à jour :
Précision GPS :
Précision DGPS (WAAS) :
Antenne :
1/seconde en continu
15 mètres (49 pieds), RMS 95% typique pour GPS
< 3 mètres (10 pieds), 95% typique pour corrections DGPS (WAAS)
antenne GPS externe
- 8 -
Download from Www.Somanuals.com. All Manuals Search And Download.
GPS NAVIGATION SYSTEM
MANUALE DI INSTALLAZIONE
KNA-G520
Avviso
La mancata osservanza dei suggerimenti forniti di seguito potrebbe causare ferite gravi o incendi.
• Non cercare di installare o riparare il modello KNA-G520. L’installazione e la riparazione dell’unità senza un’adeguata formazione ed
esperienza in apparecchiature elettroniche e accessori automobilistici possono essere pericolosi ed esporre l’utente a scosse elettriche o
altri pericoli.
• Quando si prolungano i cavi di terra, batteria e quadro, utilizzare cavi adatti per i veicoli o altri cavi con calibro pari o superiore a 0,75
mm2 (AWG 18) per evitare deterioramento e danni al rivestimento del conduttore.
• Se l’unità comincia ad emettere fumo od odori strani, spegnerlo immediatamente e rivolgersi ad un Centro di Assistenza
Autorizzato Kenwood.
• Tenere piccoli oggetti quali viti o batterie lontani dalla portata dei bambini. In caso di ingestione di questi oggetti, rivolgersi
immediatamente ad un medico.
Attenzione
La mancata osservanza dei suggerimenti forniti di seguito potrebbe causare danni a cose e persone.
• Accertarsi di mettere a terra l’unità collegandola a una fonte di alimentazione negativa a 12 VCC.
• Fissare tutti i conduttori con i morsetti dei cavi o con nastro isolante. Isolare i cavi scollegati e accertarsi che nessun filo nudo resti
scoperto.
• Accertarsi che nessun terminale o cavo scollegato entri a contatto con superfici metalliche del veicolo o qualsiasi altro conduttore
elettrico.
• Non aprire il coperchio superiore o il coperchio inferiore dell’unità.
• Il modello KNA-G520 non è resistente all’acqua.
- 9 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Cosa contiene la confezione
antenna GPS
unità principale
viti (4)
fascio di conduttori
nastri di fissaggio
hook and loop (2)
Installazione dell’unità principale
Utilizzare le viti o i nastri di fissaggio hook and loop (simili a Velcro®) forniti per montare l’unità principale nel veicolo. Scegliere
una posizione che consenta di accedere all’alloggiamento della scheda SD dell’unità. Accertarsi che l’unità sia in posizione
orizzontale (piana) e fissarla bene per ottenere prestazioni ottimali.
Attenzione
• Non installare l’unità in posizioni esposte alla luce diretta del sole, a caldo o umidità eccessivi, polvere, acqua o altri liquidi. Utilizzare
solo le viti fornite in dotazione. Se si utilizzano viti non adatte, è possibile che l’unità venga danneggiata.
• Verificare che sotto il tappetino da tagliare non ci siano cavi o altri elementi.
Installazione dell’antenna GPS
Attenzione
• Non dipingere l’antenna per non ostacolare o escludere la ricezione del segnale.
• Togliere oggetti, cumuli di neve ecc. dalla cima dell’antenna, che riducono la potenza di ricezione.
• Non tirare il cavo durante la rimozione dell’antenna o mentre se ne regola la posizione, perché si rischia di provocare un cortocircuito o
di spezzare i fili.
L’antenna GPS può essere installata all’interno o all’esterno del veicolo e deve essere fissata in posizione orizzontale per una
ricezione ottimale del segnale GPS. Installare l’antenna GPS a vista cielo. Se l’antenna viene installata all’interno del veicolo,
posizionarla vicino a un finestrino poiché i segnali GPS possono attraversare il vetro ma non il metallo. Per le posizioni consigliate
per l’antenna, fare riferimento all’immagine nella pagina seguente. Posizionare l’antenna GPS su una superficie metallica, ad
esempio il tetto del veicolo, per una ricezione ottimale.
Installazione degli accessori opzionali
Per informazioni sull’installazione del ricevitore TMC, fare riferimento alla guida di installazione fornita con il ricevitore.
Impostazione della funzionalità Posizione Stimata
La funzionalità Posizione Stimata (DR) consente al sistema di navigazione di fungere da guida anche in assenza del segnale GPS.
Dopo aver collegato il cavo rosa e avviato il sistema di navigazione, è necessario impostare la funzionalità Dead Reckoning perché
il sistema funzioni correttamente. Nella pagina Menu del sistema di navigazione, toccare Impost. > Navigazione > Impost.
Posizione Stimata > Impost..
Tipo di Onda del ContaKM - Selezionare Onda quadra o Onda sinusoidale. Stabilire l’impostazione appropriata rivolgendosi al
produttore del veicolo oppure utilizzando un oscilloscopio. Il tipo Onda quadrata è il più comune.
Polarità Luce di retromarcia - Selezionare Alta o Bassa. Per informazioni sulla polarità, rivolgersi al produttore del veicolo
oppure utilizzare un voltmetro. Scegliere Alta se viene rilevato un voltaggio positivo elevato quando si accendono le luci di
retromarcia. Scegliere Bassa se viene rilevato un voltaggio basso o assente quando si accendono le luci di retromarcia.
- 10 -
Download from Www.Somanuals.com. All Manuals Search And Download.
- 11 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Acquisizione dei segnali GPS
La prima volta che si accende KNA-G520, è necessario attendere che il sistema acquisisca i segnali satellitari. Questo processo
potrebbe richiedere alcuni minuti. Accertarsi che il veicolo sia all’aperto e lontano da edifici alti o alberi per far sì che l’acquisizione
dei segnali sia più rapida. Una volta acquisiti i segnali satellitari per la prima volta, le acquisizioni successive saranno più rapide.
Sostituzione dei fusibili
Se è necessario sostituire un fusibile sui cavi rossi o gialli, accertarsi che questi non tocchino alcuna superficie per evitare corto
circuiti. Sostituire il fusibile con uno da 2 Amp.
Attenzione
Quando si sostituisce un fusibile, utilizzare solo un fusibile con la potenza indicata. Se si utilizza un fusibile con una potenza
differente, l’unità potrebbe non funzionare correttamente. Scollegare i conduttori prima di sostituire un fusibile per evitare corto
circuiti.
Specifiche
Generale
Temperatura di funzionamento:
Temperatura di immagazzinaggio:
Voltaggio di funzionamento:
Consumo di corrente:
da -15 a 70°C
da -40 a 85°C
da 9,5 a 25 V
0,12 A (tipico) a 13 V (Max 1 A a 13 V)
70 uA (tipico) a 13 V
30 mm (A) x 120 mm (P) x 117 mm (L)
184 g
Corrente con ACC disattivato:
Dimensioni:
Peso:
Orientamento di montaggio:
Memorizzazione delle mappe:
orizzontale a +/- 5 gradi
scheda di memoria interna non rimovibile (dati delle mappe City Navigator™ precaricate)
e slot per scheda SD opzionale rimovibile
Connettori:
Sistema/alimentazione, antenna GPS, alloggiamento per scheda SD,
Mini-B per ricevitori di segnalazioni sul traffico in FM opzionali
Navigazione
Ricevitore:
ricevitore GPS a 12 canali paralleli
1.575,42 MHz
Frequenza:
Tempi di acquisizione:
A caldo:
circa 15 secondi
A freddo:
Circa 45 secondi
AutoLocate®:
circa 2 minuti
Velocità di aggiornamento:
Precisione GPS:
Precisione DGPS (WAAS):
Antenna:
1/secondo, continuo
15 metri (49 piedi) RMS 95% tipica con GPS
< 3 metri (10 piedi) 95% tipica con correzioni DGPS (WAAS)
Antenna GPS esterna
- 12 -
Download from Www.Somanuals.com. All Manuals Search And Download.
GPS NAVIGATION SYSTEM
MANUALE DI INSTALLAZIONE
KNA-G520
Warnung
Beachten Sie unbedingt die folgenden Sicherheitshinweise, um schwerwiegende Verletzungen oder die Entstehung von Feuer zu
vermeiden.
• Führen Sie die Installation des KNA-G520 oder Reparaturarbeiten nicht selbst durch. Installieren oder reparieren Sie das Gerät
nicht ohne entsprechende Ausbildung und Kenntnisse und Kenntnisse in den Bereichen Elektronik und Kfz-Zubehör. Es besteht
Verletzungsgefahr durch elektrischen Schlag und andere Risiken.
• Wenn Sie die Zündungs-, Batterie- oder Erdungskabel verlängern müssen, verwenden Sie speziell für Kfz-Zubehör geeignete Kabel
oder andere Kabel mit einem Querschnitt von mindestens 0,75 mm2 (AWG 18), um Kabelverschleiß oder Schäden am Kabelmantel zu
vermeiden.
• Schalten Sie das Gerät bei Geruch- oder Rauchentwicklung sofort aus und suchen Sie einen KENWOOD-Fachhändler auf.
• Halten Sie bitte die Einbauteile (wie Batterien und Schrauben) von Kleinkindern fern!
Achtung
Beachten Sie unbedingt die folgenden Sicherheitshinweise, um Verletzungen oder Schäden an Gegenständen zu vermeiden.
• Erden Sie das Gerät über ein negatives 12 V-Netzteil (Gleichstrom).
• Befestigen Sie alle Kabel mit Kabelklemmen oder Isolierband. Isolieren Sie lose Kabelenden; es darf kein unisolierter Draht frei
liegen.
• Stellen Sie sicher, dass keine losen Kabelenden oder Anschlüsse das Fahrzeugblech oder andere Strom leitende Teile berühren.
• Entfernen Sie nicht die oberen oder unteren Gehäuseabdeckungen.
• Das KNA-G520 ist nicht wasserdicht.
- 13 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Inhalt
GPS-Antenne
Haupteinheit
Schrauben (4)
Kabelbaum
Klettverschlüsse
(2)
Installieren der Haupteinheit
Bringen Sie die Haupteinheit mit den Schrauben oder dem Klettverschlussim Fahrzeug an. Achten Sie dabei darauf, dass der
SD-Kartensteckplatz am Gerät nicht blockiert wird. Um eine optimale Leistung zu gewährleisten, bringen Sie das Gerät horizontal
(flach) an, und stellen Sie sicher, dass es gut befestigt ist.
Achtung
• Bringen Sie das Gerät nicht an einer Stelle an, an der es direktem Sonnenlicht, extremer Hitze oder Feuchtigkeit, Staub oder
ausgelaufenen Flüssigkeiten ausgesetzt werden kann. Verwenden Sie nur die mitgelieferten Schrauben. Mit falschen Schrauben
könnten Sie das Gerät beschädigen.
• Stellen Sie vor dem Aufschneiden der Fußmatte sicher, dass sich an dieser Stelle keine Kabel oder andere Teile befinden.
Installieren der GPS-Antenne
Achtung
• Die GPS-Antenne darf nicht lackiert werden, da sonst der Empfang beeinträchtigt wird.
• Entfernen Sie Dinge wie Laub oder Schnee von der Antenne, um einen bestmöglichen Empfang zu gewährleisten.
• Ziehen Sie beim Ein- oder Ausbauen bzw. Ausrichten der Antenne nicht am Anschlusskabel, da es sonst abreißen oder einen
Kurzschluss verursachen könnte.
Die GPS-Antenne kann entweder im Fahrzeuginnenraum oder außen am Fahrzeug angebracht werden. Richten Sie sie horizontal
aus, um einen optimalen GPS-Empfang zu gewährleisten. Achten Sie darauf, dass sich keine Gegenstände oberhalb der GPS-
Antenne befinden. Wenn Sie die Antenne im Fahrzeuginnenraum montieren, bringen Sie sie in Fensternähe an; GPS-Signale
können Glas, nicht aber metallische Gegenstände durchdringen. Auf der nächsten Seite finden Sie eine Darstellung von
geeigneten Montageorten für die Antenne. Platzieren Sie die GPS-Antenne auf einer metallischen Oberfläche, beispielsweise dem
Fahrzeugdach, um einen optimalen Empfang zu gewährleisten.
Installieren von optionalem Zubehör
Informationen zum Installieren des optional erhältlichen FM-Verkehrsfunkempfängers (z. B des GTM 10) finden Sie im
Installationshandbuch des Verkehrsfunkempfängers.
Einrichten von Einstellung Koppelnavigation
Durch Einstellung Koppelnavigation (DR) ist das System in der Lage, auch bei einem Ausfall des GPS-Empfangs
Navigationshinweise zu geben. Nach dem Anschließen des rosa Kabels und dem Starten des Navigationssystems müssen Sie
Dead Reckoning zunächst einrichten, damit es ordnungsgemäß funktioniert. Gehen Sie im Hauptmenü des Navigationssystems zu
Einstell. > Navigation > Einstellung Koppelnavigation > Einstell..
Tachosignaltyp – wählen Sie Rechteck oder Sinus. Fragen Sie den Fahrzeughersteller nach der richtigen Einstellung, oder
verwenden Sie ein Oszilloskop. Rechteck ist der am meisten verbreitete Typ.
Reverse Light Polarity (Rückfahrscheinwerfer-Polung) – wählen Sie Hoch oder Niedrig aus. Erkundigen Sie sich beim
Fahrzeughersteller nach der Polarität, oder überprüfen Sie sie mit einem Voltmeter. Wählen Sie Hoch (am meisten verbreitet), wenn
bei leuchtenden Rückfahrscheinwerfern eine positive, hohe Spannung angezeigt wird. Wählen Sie Niedrig, wenn bei leuchtenden
Rückfahrscheinwerfern keine oder eine niedrige Spannung angezeigt wird.
- 14 -
Download from Www.Somanuals.com. All Manuals Search And Download.
- 15 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Empfangen von GPS-Signalen
Wenn Sie das KNA-G520 zum ersten Mal einschalten, müssen Sie warten, bis das System erstmals Satellitensignale empfängt.
Dieser Vorgang kann einige Minuten dauern. Stellen Sie sicher, dass sich Ihr Fahrzeug auf freiem Gelände und nicht in der Nähe
von hohen Gebäuden oder Bäumen befindet, damit schnellstmöglich ein Signal empfangen werden kann. Nachdem das System
erstmals Satellitensignale empfangen hat, wird dieser Vorgang die darauf folgenden Male sehr schnell ausgeführt.
Austauschen von Sicherungen
Wenn Sie Sicherungen an den roten oder gelben Kabeln austauschen müssen, stellen Sie sicher, dass sich die Kabel nicht berühren;
ansonsten besteht die Gefahr eines Kurzschlusses. Ersetzen Sie anschließend die alte Sicherung durch eine neue (2 Ampere).
Achtung
Verwenden Sie beim Austauschen von Sicherungen ausschließlich neue Sicherungen mit den vorgeschriebenen Werten. Eine Sicherung
mit falschen Werten kann Funktionsstörungen des Geräts verursachen. Klemmen Sie vor dem Austauschen einer Sicherung den
Kabelbaum ab, um Kurzschlüsse zu vermeiden.
Spezifikationen
Allgemein
Betriebstemperatur:
-15 °C bis 70 °C
Lagertemperatur:
-40 °C bis 85 °C
Betriebsspannung:
Energieverbrauch:
ACC-Abschaltstrom:
9,5 V bis 25 V
0,12 A typisch bei 13 V (max. 1,0 A bei 13 V)
70 uA typisch bei 13 V
Abmessungen (H x B x L): 30 mm x 120 mm x 117 mm
Gewicht:
184 g
Montageausrichtung:
Kartenspeicher:
horizontal +/- 5 Grad
interner, fester Speicher (vorinstallierte City Navigator™-Kartendaten) und optional erhältliche, auswechselbare
SD-Karte
Anschlüsse:
System/Ein/Aus, GPS-Antenne, SD-Kartensteckplatz, Mini-B für optional erhältlichen FM-
Verkehrsfunkempfänger
Navigation
Empfänger:
12-Kanal Parallel-GPS-Empfänger
1.575,42 MHz
Frequenz:
Startzeiten:
Warmstart:
ca. 15 Sekunden
Kaltstart:
ca. 45 Sekunden
AutoLocate®:
Positionsberechnung:
GPS-Genauigkeit:
ca. 2 Minuten
kontinuierlich 1 Mal/Sekunde
15 Meter RMS 95 % typisch mit GPS
DGPS (WAAS)-
Genauigkeit:
< 3 Meter 95 % typisch mit DGPS (WAAS)-Korrekturen
externe GPS-Antenne
Antenne:
- 16 -
Download from Www.Somanuals.com. All Manuals Search And Download.
GPS NAVIGATION SYSTEM
MANUAL DE INSTALACIÓN
KNA-G520
Advertencia
No evitar las siguientes situaciones de riesgo potencial puede provocar lesiones graves o incendios.
• No intente instalar o reparar la unidad KNA-G520 por su cuenta. La instalación o reparación de la unidad sin formación ni experiencia
en equipos electrónicos y accesorios de automoción puede resultar peligrosa y exponerle a descargas eléctricas u otros riesgos.
• Si extiende los cables de encendido, de la batería o de tierra, utilice cables de automoción con un grosor de 0,75 mm2 (AWG 18 ) o
superior para evitar que se deterioren y se dañe el revestimiento de los mismos.
• Si nota que la unidad emite humos u olores extraños, desconecte inmediatamente la alimentación y consulte con su distribuidor
Kenwood.
• Mantenga los artículos pequeños (como tornillos o baterías) fuera del alcance de los niños. Si los injirieran accidentalmente, consulte
inmediatamente a un médico.
Precaución
No evitar las siguientes situaciones de riesgo potencial puede provocar lesiones o daños materiales.
• Asegúrese de conectar a tierra la unidad en una fuente de alimentación negativa CC de 12 V.
• Asegure todos los cables con abrazaderas para cables o cinta eléctrica. Aísle los cables no conectados. No deje ningún cable desnudo al
descubierto.
• No permita que los cables o los terminales sin conectar entren en contacto con partes metálicas del vehículo o cualquier otro elemento
que sea conductor de electricidad.
• No abra las cubiertas superior o inferior de la unidad.
• El dispositivo KNA-G520 no es resistente al agua.
- 17 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Elementos incluidos
antena GPS
unidad principal
tornillos (4)
arnés de
cableado
cierres de enganche
y giro (2)
Instalación de la unidad principal
Utilice los tornillos o los cierres de enganche y giro (similares al Velcro®) proporcionados para montar la unidad principal en el
vehículo. Seleccione una ubicación que le permita acceder a la ranura de la tarjeta SD de la unidad. Cerciórese de colocar la unidad
en horizontal (sobre una superficie plana) y de asegurarla completamente para conseguir un rendimiento óptimo.
Precaución
• No instale la unidad en lugares en los que esté expuesta a la luz directa del sol, a un calor o humedad excesivos, al polvo, a caídas o a
líquidos. Utilice únicamente los tornillos que se proporcionan. Si no lo hace, puede dañar la unidad.
• Compruebe los cables u otros elementos que se encuentren debajo de la alfombrilla antes de cortarla.
Instalación de la antena GPS
Precaución
• No pinte la antena. Se podría limitar o desactivar la recepción de la señal.
• Elimine la nieve o todo objeto que se encuentre encima de la antena ya que podrían reducir el nivel de recepción.
• Cuando quite la antena o esté ajustando la posición de la misma, no tire el cable. Podría provocar un cortocircuito o la rotura de los
cables.
La antena GPS se puede instalar en el interior o el exterior del vehículo. Para conseguir una recepción óptima con el GPS, se debe
colocar en horizontal. La antena GPS debe tener una buena panorámica del cielo. Si instala la antena dentro del vehículo, colóquela
cerca de una ventana; las señales GPS pueden traspasar el cristal, pero no el metal. Consulte la imagen de la página siguiente para
saber los lugares en que se recomienda instalar la antena. Coloque la antena GPS en una superficie metálica, como el techo del
vehículo, para conseguir una recepción óptima.
Instalación de accesorios opcionales
Para ver información sobre la instalación del receptor FM Traffic opcional (como el modelo GTM 10), consulte la guía de
instalación que se incluye con el mismo.
Configuración de Navegación por estima
Dead Reckoning (DR, Navegación por estima) permite que el sistema de navegación siga guiando los desplazamientos aunque
pierda la recepción GPS. Tras conectar el cable rosa e iniciar el sistema de navegación, debe configurar Dead Reckoning
(Reconocimiento continuo) para que todo funcione correctamente. En la página de menús del sistema de navegación, toque Config.
> Navegación > Configuración de la navegación por estima > Config..
Tipo onda cuentakilómetros: seleccione Onda cuadrada o Onda senoidal. Para saber cuál es la configuración adecuada, póngase
en contacto con el fabricante del vehículo o utilice un osciloscopio. El tipo más común es la onda cuadrada.
Polaridad luz marcha atrás: seleccione Alto o Bajo. Póngase en contacto con el fabricante del vehículo para conocer la polaridad
o compruébela con un voltímetro. Establezca el valor más común Alto si se detecta un alto voltaje positivo cuando se encienden las
luces de marcha atrás. Establezca Bajo si no se detecta voltaje o se detecta un bajo voltaje cuando se encienden las luces de marcha
atrás.
- 18 -
Download from Www.Somanuals.com. All Manuals Search And Download.
- 19 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Obtención de señales GPS
Al realizar el primer encendido del dispositivo KNA-G520, debe esperar hasta que el sistema obtenga señales del satélite por
primera vez. Este proceso puede llevar varios minutos. Asegúrese de que el vehículo está situado en el exterior, en una zona abierta
y alejada de edificios y árboles de gran altura, para que la adquisición resulte más rápida. Una vez que el sistema ha adquirido los
satélites por primera vez, lo hará más rápido en las ocasiones sucesivas.
Cambio de los fusibles
Si debe reemplazar un fusible de los cables rojo o amarillo, asegúrese de que los cables no se tocan, pues podría provocar un
cortocircuito. A continuación, reemplace el fusible antiguo por uno nuevo de 2 amperios.
Precaución
Al reemplazar un fusible, utilice únicamente fusibles nuevos del tipo especificado. Si utiliza un fusible equivocado, puede provocar un
funcionamiento erróneo de la unidad. Desconecte el arnés de cableado antes de reemplazar un fusible para evitar cortocircuitos.
Especificaciones
Generales
Temperatura de funcionamiento: De -15°C a 70°C
Temperatura de almacenamiento: De -40°C a 85°C
Voltaje de funcionamiento:
Consumo eléctrico:
ACC sin corriente:
Dimensiones:
De 9,5 V a 25 V
0,12 A (típico) a 13 V (Máximo de 1,0 A a 13 V)
70 uA (típica) a 13 V
30 mm (Al.) x 120 mm (An.) x 117 mm (L)
184 g
Peso:
Orientación de montaje:
Almacenamiento de mapas:
Horizontal +/- 5 grados
Memoria interna no extraíble (datos de mapas de City Navigator™ precargados) y tarjeta SD extraíble
opcional
Conectores:
Sistema/alimentación, antena GPS, ranura de tarjeta SD, Mini-B para receptores FM Traffic opcionales
Navegación
Receptor:
Receptor GPS de 12 canales paralelos
1.575,42 MHz
Frecuencia:
Tiempos de adquisición:
En caliente:
Aproximadamente 15 segundos
En frío:
Aproximadamente 45 segundos
AutoLocate®:
Aproximadamente 2 minutos
Frecuencia de actualización:
Precisión GPS:
Precisión DGPS (WAAS):
Antena:
1 vez por segundo, continuada
15 metros, valor efizcaz del 95% típico con GPS
< 3 metros, 95% típica con correcciones DGPS (WAAS)
Antena GPS externa
- 20 -
Download from Www.Somanuals.com. All Manuals Search And Download.
GPS NAVIGATION SYSTEM
MANUAL DE INSTALAÇÃO
KNA-G520
AVISO
A não prevenção das situações potencialmente perigosas enumeradas a seguir poderá provocar ferimentos graves ou incêndios.
• Não tente instalar ou reparar o KNA-G520 sozinho. A instalação e reparação da unidade sem formação e experiência no manejo de
equipamento eléctrico e acessórios para automóvel podem ser perigosas e expô-lo ao risco de choques eléctricos e outros acidentes.
• Quando aumentar o comprimento dos cabos de terra, bateria ou ignição, utilize cabos adequados para a utilização em automóveis ou
outros cabos de calibre 0,75 mm2 (AWG 18) ou superior, de modo a evitar a deterioração dos cabos e os danos ao seu revestimento.
• Se a unidade começar a deitar fumo ou odores estranhos, desligue imediatamente a alimentação e consulte o seu
distribuidor.
• Mantenha os pequenos objectos (tais como parafusos ou pilhas) longe do alcance de crianças. Se algum destes objectos for
acidentalmente engolido, consulte um médico de imediato.
Atenção
A não prevenção das situações potencialmente perigosas enumeradas a seguir poderá provocar ferimentos ou danos à
propriedade.
• Certifique-se de que liga a unidade a uma fonte de alimentação de 12 V CC.
• Fixe todos os cabos com grampo ou fita eléctrica. Isole os cabos não ligados; não permita que cabos descobertos permaneçam
expostos.
• Não permita que cabos ou terminais não ligados toquem em metal no veículo ou em qualquer outro objecto condutor de electricidade.
• Não retire a tampa superior ou inferior da unidade.
• O KNA-G520 não é impermeável.
- 21 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Peças Incluídas
antena GPS
unidade
principal
parafusos (4)
cablagem
fechos de
abertura fácil (2)
Instalação da unidade principal
Utilize os parafusos ou fechos de abertura fácil (semelhantes ao Velcro®) fornecidos para montagem da unidade no veículo.
Seleccione um local que lhe permita aceder à ranhura de cartão SD da unidade. Certifique-se de que coloca a unidade na posição
horizontal e fixe-a bem para obter o melhor desempenho.
Atenção
• Não instale a unidade num local onde esteja exposta os raios directos do sol, a calor ou humidade excessivos, ao pó, derrames ou
líquidos. Apenas utilize os parafusos fornecidos. Se utilizar os parafusos incorrectos, poderá danificar a unidade.
• Verifique a existência de cabos ou outras peças debaixo do revestimento do solo antes de cortá-lo.
Instalação da antena GPS
Atenção
• Não pinte a antena. Isso pode dificultar ou impedir a recepção dos sinais.
• Retire qualquer objecto próximo, neve acumulada, etc., do topo da antena. A intensidade do sinal recebido será reduzida.
• Não puxe pelo cabo ao retirar a antena ou quando ajusta a sua posição. Isto poderá causar um curto-circuito nos fios ou o seu
rompimento.
A antena GPS pode ser instalada no interior ou exterior do veículo. Deverá ser colocada na horizontal para garantir a melhor
recepção de dados GPS. O campo de visão (do céu) da antena GPS deverá estar desimpedido. Se a instalar no interior do veículo,
coloque-a junto à janela; os sinais GPS atravessam o vidro, mas não o metal. Consulte a imagem na página seguinte, referente
aos locais recomendados para instalação da antena. Coloque a antena GPS numa superfície metálica, tal como o tejadilho do seu
veículo, para melhor recepção.
Instalação dos acessórios opcionais
Para obter informação acerca da instalação do receptor FM de informação de trânsito (tal como o GTM 10), consulte o Manual de
Instalação fornecido com o receptor de informação de trânsito.
Configuração do Dead Reckoning
A função de Dead Reckoning (DR) permite ao sistema de navegação continuar a fornecer indicações de navegação, mesmo quando
perde o sinal GPS. Depois de ligar o cabo cor-de-rosa e iniciar o sistema de navegação, terá de configurar o Reconhecimento sem
Sinal para que este funcione correctamente. A partir da página de Menu do sistema de navegação, toque em Definir> Navegação >
Configuração em Dead Reckoning > Definir.
Tipo de onda do odómetro—seleccione Onda Quadrada ou Onda sinuzoidal. Averigúe a definição adequada contactando o
fabricante do veículo ou recorrendo a um osciloscópio. A Onda Quadrada é o tipo mais comum.
Polaridade da luz marcha atras—seleccione Alta ou Baixa. Contacte o fabricante do veículo ou utilize um voltímetro para
determinar a polaridade. Defina para Alta (a mais comum) se for detectada uma tensão alta positiva quando os faróis traseiros estão
iluminados. Defina para Baixa, se for detectada pouca ou nenhuma tensão quando os faróis traseiros estão iluminados.
- 22 -
Download from Www.Somanuals.com. All Manuals Search And Download.
- 23 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Obtenção de Sinais GPS
Quando ligar o KNA-G520 pela primeira vez, deverá aguardar enquanto o sistema obtém sinais de satélite pela primeira vez. Este
processo poderá demorar vários minutos. Certifique-se de que o seu veículo se encontra no exterior, numa área aberta, longe de
edifícios altos e árvores de modo a acelerar o processo. A partir da obtenção de sinais pela primeira vez, tal processo será muito
mais rápido.
Mudança dos Fusíveis
Se precisar de mudar um fusível nos cabos vermelho ou verde, certifique-se de que os cabos não se tocam; deste modo, evita os
curto-circuitos. Em seguida, substitua o fusível por um fusível novo de 2 Amp.
Atenção
Quando mudar um fusível, utilize apenas um fusível com a potência indicada. A utilização de um fusível com a potência inadequada
poderá provocar o mal funcionamento da unidade. Desligue os cabos antes de mudar um fusível para evitar curto-circuitos.
Especificações
Gerais
Temperatura de funcionamento: -15°C a 70°C
Temperatura de armazenamento: -40°C a 85°C
Tensão de funcionamento:
Consumo de corrente:
9,5 V to 25 V
0,12 A (valor típico) a 13 V (Max. de 1,0 A a 13 V)
Intensidade da corrente com
circuito desligado:
70 uA (valor típico) a 13 V
30 mm (A) x 120 mm (L) x 117 mm (C)
184 g
Dimensões:
Peso:
Orientação da Montagem:
Armazenamento dos Mapas:
Horizontal +/- 5 graus
Memória interna não amovível (dados de mapa City Navigator™ pré-carregados) e cartão SD removível
opcional
Conectores:
Sistema/alimentação, antena GPS, ranhura de cartão SD, mini B para receptores FM de informação de
trânsito (opcionais)
Navegação
Receptor:
Receptor GPS de 12 canais paralelos
1.575,42 MHz
Frequência:
Tempos de obtenção:
A quente:
Aprox. 15 segundos
A frio:
Aprox. 45 segundos
AutoLocate®:
Aprox. 2 minutos
Taxa de actualização:
Precisão do GPS:
Precisão do DGPS (WAAS):
Antena:
1/segundo, contínua
15 metros RMS 95% (valor típico) com GPS
< 3 metros 95% (valor típico) com correcções DGPS (WAAS)
Antena GPS externa
- 24 -
Download from Www.Somanuals.com. All Manuals Search And Download.
GPS NAVIGATION SYSTEM
INSTALLATIE HANDLEIDING
KNA-G520
Waarschuwing
Vermijd de volgende situaties omdat deze brandgevaar kunnen opleveren of kunnen leiden tot ernstig letsel.
• Installeer of repareer de KNA-G520 niet zelf. Het installeren en repareren van het onderdeel zonder kennis van en ervaring met
elektronische apparatuur en autoaccessoires kan gevaarlijk zijn en u loopt risico op een elektrische schok of ander gevaar.
• Wanneer u de ontstekings-, accu- of aardekabels verlengt, dient u kabels te gebruiken voor voertuigen, of andere kabels met een
diameter van 0,75 mm2 (AWG 18) of dikker om slijtage en beschadiging van de coating te voorkomen.
• Schakel de spanning direkt uit en raadpleeg uw Kenwood dealer indien er rook of een vreemde geur uit het toestel komt.
• Houd kleine voorwerpen (zoals bijvoorbeeld schroefjes of batterijen) buiten bereik van kinderen. Als zulke voorwerpen per ongeluk
ingeslikt worden, raadpleeg dan onmiddellijk een arts.
Let op
Vermijd de volgende mogelijk gevaarlijke situaties omdat deze kunnen leiden tot letsel of beschadiging van uw eigendom.
• Zorg ervoor dat het onderdeel aardt op een negatieve voedingsbron van 12 V gelijkstroom.
• Maak alle kabels vast met kabelklemmen of isolatietape. Isoleer losse bedrading; laat geen bedrading blootliggen.
• Laat losliggende kabels of aansluitingen niet in contact komen met het metaal van het voertuig of iets anders dat elektriciteit geleidt.
• Open nooit de boven- of onderpanelen van het toestel.
• De KNA-G520 is niet waterdicht.
- 25 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Bijgeleverde onderdelen
GPS-antenne
hoofdeenheid
schroeven (4x)
kabelgeleider
klittenband (2x)
De hoofdeenheid installeren
Gebruik de bijgeleverde schroeven of de klittenband bevestiging om de hoofdeenheid in het voertuig te bevestigen. Kies een locatie
waarvandaan u de SD-kaartsleuf van het onderdeel kunt bereiken. Zorg ervoor dat u het onderdeel horizontaal (liggend) bevestigt
en zet het voor een optimale werking stevig vast.
Let op
• Installeer de eenheid niet op een plaats waar deze wordt blootgesteld aan direct zonlicht, zeer veel hitte of vocht, stof, kruimels of
vloeistof. Gebruik uitsluitend de meegeleverde schroeven. Als u de verkeerde schroeven gebruikt, kan de eenheid beschadigd raken.
• Controleer of er geen kabels en andere onderdelen onder de automat liggen voordat u deze insnijdt.
De GPS-antenne installeren
Let op
• Verf de antenne niet. Hierdoor wordt de ontvangst van het signaal beïnvloed of onmogelijk gemaakt.
• Verwijder ieder mogelijk voorwerp of opeengehoopte sneeuw van de top van de antenne. Hierdoor neemt namelijk het
ontvangstvermogen af.
• Trek niet aan het snoer als u de antenne verwijdert of zijn positie afstelt. Hierdoor kan kortsluiting veroorzaakt worden of kunnen de
snoeren doorbreken.
De GPS-antenne kan aan de binnen- of buitenkant van het voertuig worden geïnstalleerd. U dient deze horizontaal te plaatsen voor
een optimale GPS-ontvangst. Er mag geen blokkade zijn tussen de GPS-antenne en de lucht. Plaats de antenne dicht bij een ruit
als u de antenne in het voertuig installeert, omdat de GPS-signalen door glas gaan, maar niet door metaal. Raadpleeg de afbeelding
op de volgende pagina voor plaatsen die worden aanbevolen om de antenne te installeren. Plaats de GPS-antenne voor de beste
ontvangst op een metalen oppervlak, zoals het dak van uw voertuig.
Optionele accessoires installeren
Raadpleeg de Installatiehandleiding voor informatie over het installeren van de optionele FM-ontvanger voor verkeersinformatie
(zoals de GTM 10) die wordt geleverd bij de verkeersinformatieontvanger.
Gegist-bestekfunctie instellen
Met de gegist-bestekfunctie (DR of dead reckoning) kan het navigatiesysteem navigatiebegeleiding blijven geven, zelfs als er geen
GPS-ontvangst is. Als u de roze kabel hebt aangesloten en het navigatiesysteem hebt gestart, dient u de gegist-bestekfunctie in te
schakelen om het systeem correct te laten werken. In de menupagina van het navigatiesysteem drukt u op Instell. > Navigatie >
Instellen gisbestek > Instell..
Kilometerteller golfvorm - selecteer de Blokgolf of Sinusoïdegolf. Bepaal de juiste instelling door dit na te gaan bij de fabrikant
van het voertuig, of met een oscilloscoop. Blokgolf is het meest voorkomende soort.
Achteruitrijlicht polariteit - selecteer Hoog of Laag. Neem contact op met de fabrikant van het voertuig of gebruik een voltmeter
om te weten te komen wat de polariteit is. Stel dit in op Hoog (meest voorkomend) als u een positieve, hoge spanning meet wanneer
de achteruitrijverlichting brandt. Stel dit in op Laag als u geen of een lage spanning meet wanneer de achteruitrijverlichting brandt.
- 26 -
Download from Www.Somanuals.com. All Manuals Search And Download.
- 27 -
Download from Www.Somanuals.com. All Manuals Search And Download.
GPS-signalen zoeken
Als u de KNA-G520 voor het eerst inschakelt, dient u even te wachten terwijl het systeem voor het eerst satellietsignalen zoekt. Dit
proces kan enkele minuten duren. Om het zoeken snel te laten verlopen, kunt u uw voertuig het beste buiten op een open locatie
parkeren, en niet in de buurt van hoge gebouwen en bomen. Nadat het systeem voor het eerst satellieten heeft gezocht, zal het in het
vervolg sneller satellieten vinden.
De zekeringen vervangen
Als er een zekering moet worden vervangen voor de rode of gele kabels, mogen de kabels elkaar niet raken omdat dit kortsluiting
kan veroorzaken. Vervang de oude zekering door een nieuwe van 2 ampère.
Let op
Gebruik een nieuwe zekering met de voorgeschreven weerstand als u een zekering vervangt. Als u een zekering met een
onjuiste weerstand gebruikt, werkt de eenheid mogelijk niet goed. Koppel om kortsluiting te voorkomen de kabelgeleider
los voordat u een zekering vervangt.
Specificaties
Algemeen
Bedrijfstemperatuur:
Opslagtemperatuur:
Bedrijfsspanning:
Stroomverbruik:
Stroom ACC/OFF:
Afmetingen:
-15 °C tot 70 °C
-40 °C tot 85 °C
9,5 V tot 25 V
0,12 A bij 13 V (max. 1 A bij 13 V)
70 uA bij 13 V
HxBxL = 30 x 120 x 117 mm
184 g
Gewicht:
Bevestigingshoek:
Kaartopslag:
horizontaal +/- 5 graden
intern niet-verwijderbaar geheugen (voorgeladen kaartgegevens voor City Navigator™) en optionele
verwijderbare SD-kaart
Connectors:
systeem/voeding, GPS-antenne, SD-kaartsleuf, mini-B voor optionele FM-ontvangers voor
verkeersinformatie
Navigatie
Ontvanger:
GPS-ontvanger voor 12 parallelle kanalen
1575,42 MHz
Frequentie:
Zoektijden:
Bij warm weer:
Bij koud weer:
AutoLocate®:
ca. 15 seconden
ca. 45 seconden
ca. 2 minuten
Ontvangstfrequentie:
Nauwkeurigheid GPS:
1 x per seconde, continu
15 meter (49 ft), RMS 95% met GPS
Nauwkeurigheid DGPS (WAAS): < 3 meter (10 ft), 95% met DGPS (WAAS)-correcties
Antenne: externe GPS-antenne
- 28 -
Download from Www.Somanuals.com. All Manuals Search And Download.
|
InSinkErator Water Dispenser GN1100 User Manual
Intel Computer Accessories OPEN 660 120 140 150 II User Manual
Intel Computer Hardware GME965 User Manual
Invacare Home Care Product Folding Commode User Manual
JVC Computer Monitor DT V100CG User Manual
JVC Computer Monitor TM 2703U User Manual
Kenmore Freezer 25344133800 User Manual
Kenwood Stereo System KRF V6200D User Manual
KitchenAid Refrigerator KBLO36FMX01 User Manual
Kompernass Sander PEBS 900 User Manual