JobSite Systems Speaker System LSS 10 User Manual

INSTALLATION & USER GUIDE

For Powerful Bass in Home

Theater or Music Systems

LSS-10 LSS-12

10" & 12" POWERED SUBWOOFERS

DS00490ACN-0 LSS-10_12.indd

5/23/06

2:12:53 PM

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFETY INSTRUCTIONS

The lightning ﬂash with arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the

presence of uninsulated dangerous voltage within the

product’s enclosure that may be of sufﬁcient magnitude

to constitute a risk of electric shock to persons.

WARNING: To reduce the risk of ﬁre or electric shock,

do not expose this apparatus to rain or

moisture

The exclamation point within an equivalent triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in

the literature accompanying the appliance.

CAUTION

CAUTION: TO REDUCE THE

RISK OF ELECTRICAL SHOCK,

DO NOT REMOVE COVER. NO

USER SERVICEABLE PA R T S

I N S I D E . R E F E R SERVICING

QUALIFIED

SERVICE

PERSONNEL.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any ventilation openings. Install in according with the manufacturer’s

instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other

apparatus (including ampliﬁers) that produce heat.

9. Do not defeat the safety purpose of the polarized or ground plug. A polarized plug has

two blades with one wider than the other. A grounding-type plug has two blades and a

third grounding prong. The wide blade is provided for your safety. If the provided plug

does not ﬁt into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched

particularly at plug, convenience receptacles, and the point

where they exit from the apparatus.

11. Only use attachments/accessories speciﬁed by the

manufacturer.

12. Use only with a cart, stand, tripod, bracket, or table speciﬁed

by the manufacturer, or sold with the apparatus. When a cart is

used, use caution when moving the cart/apparatus combination

to avoid injury from tip-over.

13. Unplug this apparatus during lighting storms or when unused for long periods of time.

14. Refer all servicing to qualiﬁed service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power-supply cord or plug is

damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does not operate normally, or has been dropped.

15. Apparatus shall not be exposed to dripping or splashing, and no objects ﬁlled with liquids

shall be placed on the apparatus.

DS00490ACN-0 LSS-10_12.indd

5/23/06

2:12:54 PM

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION

Signal Connectors and Power Controls

The LSS-10 and LSS-12’s signal connectors and power controls are located on the unit’s rear

panel, as shown in Figure 1. They function as follows:

NOTE: See Applications starting on page 7 for detailed wiring connections for

your application.

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

Figure 1. The LSS-12’s rear panel contains the subwoofer’s signal connectors and

power controls. (LSS-12 Shown - LSS-10 similar)

1. TRIGGER: For external power triggering, use a mini (3.5 mm) mono plug to connect the IN

jack to a power on/off trigger signal from a home theater surround sound processor or

other voltage. Source power on is 3 to 30 Vdc (or Vac). Power off is 0 Vdc (or Vac). Use

the OUT jack to pass the TRIGGER signal (at the same voltage level of the trigger input)

to another LSS-10 and LSS-12 or other equipment in your system. THIS JACK SHOULD

NOT BE USED TO POWER OTHER EQUIPMENT.

NOTE: For a system not equipped with a power trigger output, consider using a 12-volt

power supply as a trigger signal that is activated via a switched AC outlet on the receiver.

DS00490ACN-0 LSS-10_12.indd

5/23/06

2:12:56 PM

Download from Www.Somanuals.com. All Manuals Search And Download.

2. (Auto) POWER Switch: Use the ALWAYS ON mode to leave the LSS-10 and LSS-12 always

on. Use the MUSIC/VOLTAGE SENSE mode to automatically power on the LSS-10 and

LSS-12 when audio signals are present or when system trigger is used. When signals are

absent, the LSS-10 and LSS-12 will enter the standby mode.

NOTE: The ALWAYS ON and MUSIC/VOLTAGE SENSE settings are only active after (Master)

POWER is set to ON (see below).

3. AUDIO IN jacks: Use these gold-plated, line-level RCA input jacks to connect line-level

stereo or LFE audio signals from a home theater surround sound processor or receiver.

The LFE (Low Frequency Effects) input is not affected by the LOW PASS Frequency

Control. The PHASE Control and LEVEL Control continue to function as normally expected.

4. AUDIO OUT jacks: Use these gold-plated, line-level RCA output jacks to connect

line-level stereo or LFE audio signals to drive another LSS-10 or LSS-12 or loop your line

level audio signal back to your surround sound processor or receiver. (The L/R output

signals are routed through a fixed HIGH-PASS (80 Hz) filter).

5. SPEAKER IN Binding Posts: As an alternative to the AUDIO IN jacks, use the loudspeaker-

level, gold-plated, five-way binding posts to connect loudspeaker-level, stereo audio

signals from a home theater surround sound processor or receiver. For additional

connection details, see Finishing the Installation on page 5.

6. SPEAKER OUT Binding Posts: As an alternative to the AUDIO OUT jacks, use the

loudspeaker-level, gold-plated, five-way binding posts to connect loudspeaker-level,

stereo audio signals to drive your front L/R satellite loudspeakers.

7. (Master) POWER Switch: Use this control to power on/off the LSS-10 and LSS-12.

8. Detachable IEC Power Cord and built-in fuse. If needed, replace the fuse with same type,

as follows:

■ For 115/120 Vac @ 60 Hz, use a T5AL, 250V fast-blow fuse.

■ For 230/240 Vac @ 50 Hz, use a T3.15AL, 250V fast-blow fuse.

DS00490ACN-0 LSS-10_12.indd

5/23/06

2:12:58 PM

Download from Www.Somanuals.com. All Manuals Search And Download.

CONTROLS AND CONNECTORS

Operation Controls

The LSS-10 and LSS-12’s operation controls are located on the unit’s front panel, as shown in

Figure 2. They function as follows:

Figure 2. The LSS-10 and LSS-12’s front panel contains the subwoofer’s operation controls.

1. LOW PASS Frequency Control: Use this control to set the upper frequency level that the

subwoofer will reproduce. It can be between 60 to 125 Hz. Also see SETTING UP THE

LSS-10 AND LSS-12 on page 5.

2. LEVEL Control: Use this control to adjust the subwoofer output level as desired.

3. PHASE Control: Use this control to set the subwoofer’s phase response for either 0 or

180°. Also see SETTING UP THE LSS-10 AND LSS-12 on page 5.

4. MODE indicator shows current status of the LSS-10 and LSS-12: Green is ON; Red is

STANDBY.

DS00490ACN-0 LSS-10_12.indd

5/23/06

2:12:58 PM

Download from Www.Somanuals.com. All Manuals Search And Download.

FINISHINGTHE INSTALLATION

Adjusting the Feet

2. Connect the other end of the

loudspeaker wires to the home theater

receiver (or amplifier) and satellite

loudspeakers in the same way.

The LSS-10 and LSS-12 are equipped with

four adjustable spiked feet, pre-installed

with large, slip-on rubber covers. At the final

placement location, adjust the feet/spikes

as follows:

3. Using the five-way binding post of

the LSS-10 and LSS-12, connect the

loudspeaker outputs to the appropriate

satellite loudspeaker in the same way.

■ On hard floors (e.g., wood, tile, etc.),

check the LSS-10 and LSS-12’s stability

and, if needed, adjust the rubber feet one

at a time until the cabinet is level.

4. Turn on the home theater receiver and

calibrate all loudspeakers in the system

according to the receiver (processor)

manufacturer’s instructions.

■ On carpeted floors, tilt the LSS-10 and

LSS-12 up and remove each rubber

cover. Check the LSS-10 and LSS-12’s

stability and, if needed, adjust the spikes

one at a time until the cabinet is level.

Setting Up the LSS-10 and

LSS-12

After making all the connections and

calibrating the loudspeakers, set up

the LSS-10 and LSS-12 by performing

the following steps (see Controls and

Connectors on page 4 for information on

control operation):

Connecting the LSS-10 and

LSS-12

Connect the LSS-10 and LSS-12 according

to your application (see APPLICATIONS on

page 7). Use high-quality RCA cables for all

line-level connections (see CONTROLS AND

CONNECTORS on page 4). For applications

with loudspeaker-level connections,

perform the following steps:

1. On the rear panel, set the (Auto) POWER

switch to ALWAYS ON or MUSIC/

VOLTAGE SENSE. Depending on your

application.

2. On the front panel, set the following

controls (and switches) to their initial

positions:

1. At each LSS-10 and LSS-12 loudspeaker-

level connection, separate the

■ LEVEL control = 5

loudspeaker wire so that at least 2

inches of each conductor are free. Strip

away 1/4 inch of insulation from each

loudspeaker wire. Using correct polarity,

connect the appropriate conductor

to each five-way, speaker level, input

binding post.

■ LOW PASS FREQUENCY control

= 120 Hz

■ PHASE control = 0°

3. While playing a favorite music track,

adjust your system’s volume control to a

comfortable level and listen to the bass

level at your favorite listening position

(e.g., couch).

NOTE: Observe correct polarity: Positive (+)

goes to the RED post and negative (–) goes

to the BLACK post.

DS00490ACN-0 LSS-10_12.indd

5/23/06

2:12:59 PM

Download from Www.Somanuals.com. All Manuals Search And Download.

4. Continue listening to your favorite

music and movie sources. If you want

a more solid-sounding bass (with less

overtones), try moving the LOW PASS

FREQUENCY control toward the lower

frequencies. Experiment with different

frequency settings until you find one

that sounds best. If needed, readjust the

LEVEL control (see step 3).

A pair of out-of-phase loudspeakers works

against each other, and the sound of the

two playing together will be lacking in bass

and sound “phasey.” If you suspect the

sound is not right, and you cannot see any

markings on the wire, try this simple test:

1. Stand halfway between the satellite

loudspeakers.

2. Play some music with the amplifier or

receiver set to Mono.

5. Continue listening to your favorite

music and movie sources using the

appropriate setting for LEVEL SETUP.

Try experimenting with the PHASE

control until you find its optimum setting.

Depending on the LSS-10 and LSS-12

placement, the bass should sound more

pronounced when the phase has been

optimized.

3. Listen to the richness of the bass and the

loudness of the sound.

4. Turn off the amplifier and reverse the

connections on the LSS-10 and LSS-12

SPEAKER OUT binding post.

5. Repeat the listening test with the same

volume control setting. When the sound

has a richer bass and is slightly louder,

the satellite loudspeakers are working

together or “in-phase.”

Checking Phase on the

Satellite Loudspeakers

Loudspeaker wire has two conductors. On

applications with satellite loudspeakers,

one conductor is attached to a component’s

negative (–) terminal, while the other is

attached to a component’s positive (+)

terminal. Usually, the wire is marked for your

convenience, but the marking can be done

in the following different ways:

Installing and Removing the

Grille

■ To install the grille, start with the top two

grille posts and gently press the grille

frame in at each of the five recessed

holes. When properly installed, the grille

will be approximately 2 to 3 mm away

■ Stripe on one wire

from the cabinet along the sides.

■ Ribbed area you can feel on one

conductor

■ To remove the grille, start with the bottom

grille posts and gently pull the grille frame

away from the LSS-10 and LSS-12’s edge

at each of the five recessed holes. Store

the grille in a safe place for future use.

■ Different colors of metal wire on each

conductor

■ Fabric strand or string wound into one of

the conductors

Cleaning

Use a dampened soft cloth or paper towel

to clean the cabinet and grille.

Of course, there are some wires that appear

completely identical. If wired incorrectly,

one satellite loudspeaker will be playing

“out-of-phase” with the other loudspeaker.

DS00490ACN-0 LSS-10_12.indd

5/23/06

2:12:59 PM

Download from Www.Somanuals.com. All Manuals Search And Download.

APPLICATIONS

The JobSite LSS-10 and LSS-12 Subwoofers are very flexible and can be configured for use

in various applications with associated external audio components, as shown in Figure 3

through 5. For other LSS-10 and LSS-12 applications, consult your local JobSite dealer for

help in configuring your home theater system.

LSS-12 Back

LFE Input

LFE

Output

Home Theater

Receiver

DO not use these when using the AUDIO IN ports

Speaker level

Figure 3. Line level connections

DS00490ACN-0 LSS-10_12.indd

5/23/06

2:13:02 PM

Download from Www.Somanuals.com. All Manuals Search And Download.

Two LSS-10 and LSS-12’s with Satellite Loudspeaker System

NOTE: ADJUST SETTING ON BOTH LSS-10 AND LSS-12 SUBWOOFER TO BE THE SAME

Speaker left out

Speaker Right out

JobSite M64

Receiver

Subwoofer line input

Trigger output

LSS-12 Back

Optionally, you may wire

in a similar fashion, using

the speaker level inputs

and outputs.

Figure 4. Stereo/dual subwoofer application

DS00490ACN-0 LSS-10_12.indd

5/23/06

2:13:13 PM

Download from Www.Somanuals.com. All Manuals Search And Download.

LSS-10 and LSS-12 and Speaker-Level Connection to Satellite

Loudspeakers

LSS-12 Back - LSS-10 similar

DO not use these ports when using

the SPEAKER ports

Speaker level inputs

JobSite A45-X2

Left satellite

speaker

Right satellite

speaker

Figure 5. Speaker level connections

DS00490ACN-0 LSS-10_12.indd

5/23/06

2:13:26 PM

Download from Www.Somanuals.com. All Manuals Search And Download.

SPECIFICATIONS:

can radiate radio frequency energy and

if not installed and used in accordance

with the instructions, may cause harmful

interference to radio communications.

However, there is no guarantee that

interference will not occur in a particular

installation.

Driver Complement

LSS-10: One 10" Long-Throw Front-Firing

Injection Molded Polypropylene Woofer

LSS-12: One 12" Long-Throw Front-Firing

Injection Molded Polypropylene Woofer

Amplifier Power

LSS-10: 90 Watts (rms), 125 Watts (peak)

If this equipment does cause harmful

interference to radio or television

reception, which can be determined by

turning the equipment off and on, the

user is encouraged to try to correct the

interference by one or more of the following

measures:

LSS-12: 190 Watts (rms), 260 Watts (peak)

Frequency Response

LSS-10: 30 to 160 Hz, +/- 3 dB

LSS-12: 27 to 160 Hz, +/- 3 dB

Power Requirements

LSS-10 and LSS-12:120 Vac; 230-240 Vac,

50/60Hz

■ Reorient or relocate the receiving

antenna.

■ Increase the separation between the

Overall Dimensions (with grille)

LSS-10: 14.25" W x 15.25" H x 17.25" D

equipment and receiver.

LSS-12: 14.25" W x 19" H x 19" D

■ Connect the equipment into an outlet on

a circuit different from that to which the

receiver is connected.

Weight

LSS-10: 47 lbs, (21.3 kg) shipping weight

■ Consult the dealer or an experienced

LSS-12: 57 lbs, (26 kg) shipping weight

audio/video installer for help.

Certification

• Meets FCC Part 15 and ICES-003, Class B

for USA and Canada

This equipment has been verified to comply

with the limits for a class B computing

device, pursuant to FCC Rules. In order to

maintain compliance with FCC regulations,

shielded cables must be used with this

equipment. Operation with non-approved

equipment or unshielded cables is likely

to result in interference to radio and TV

reception. The user is cautioned that

changes and modifications made to

the equipment without the approval of

manufacturer could void the user’s authority

to operate this equipment.

• CSA Listed and tested under UL/EN60065

standard

• CE compliant for the EU

• C-Tick compliant for Australia and New

Zealand

FCC INSTRUCTIONSTOTHE

USER

This equipment has been tested and found

to comply with the limits for a class B digital

device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide

reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses and

DS00490ACN-0 LSS-10_12.indd

5/23/06

2:13:34 PM

Download from Www.Somanuals.com. All Manuals Search And Download.

To obtain warranty service, you must write

to JOBSITE: Include your name, address,

telephone number, model number and serial

number of your unit, and a brief description of

the problem.

LIMITED WARRANTY

JobSite Systems (“JOBSITE”), a Niles Audio

Corporation company, warrants its passive

products (those not requiring AC or battery

power) to the original purchaser to be free

of manufacturing defects in material and

workmanship for a period of ten years from date

of purchase.

A factory Return Authorization Number

will be sent to you. DO NOT RETURN

ANY UNIT WITHOUT FIRST RECEIVING

WRITTEN AUTHORIZATION AND SHIPPING

INSTRUCTIONS FROM JOBSITE.

JOBSITE warrants its passive loudspeaker

products (those not requiring AC or battery

power) to the original purchaser to be free

of manufacturing defects in material and

workmanship for a period of five years from date

of purchase.

If the above conditions are met, the purchaser’s

sole remedy shall be to return the product to

JOBSITE, in which case JOBSITE will repair or

replace, at its sole option, the defective product

without charge for parts or labor. JOBSITE

will return the unit repaired or replaced under

warranty by shipping it by its usual shipping

method from the factory (only) at its expense

within the United States of America. THERE

ARE NO OTHER WARRANTIES, INCLUDING,

WITHOUT LIMITATION, EITHER EXPRESS OR

IMPLIED WARRANTIES OF MERCHANTABILITY

OR FITNESS FOR A PARTICULAR PURPOSE,

WITH RESPECT TO THE PRODUCT.

JOBSITE warrants its indoor/outdoor

loudspeaker products to the original purchaser

to be free of manufacturing defects in material

and workmanship for a period of two years from

date of purchase.

JOBSITE warrants its all weather rock

loudspeaker products to the original purchaser

to be free of manufacturing defects in material

and workmanship for a period of five years from

date of purchase.

REPAIR OR REPLACEMENT AS PROVIDED

UNDER THIS WARRANTY IS THE EXCLUSIVE

REMEDY OF THE CONSUMER/PURCHASER.

JOBSITE SHALL NOT BE RESPONSIBLE

FOR ANY INCIDENTAL OR CONSEQUENTIAL

DAMAGES EXCEPT TO THE EXTENT PROVIDED

(OR PROHIBITED) BY APPLICABLE LAW.

JOBSITE warrants its active products (those

requiring AC or battery power) to the original

purchaser to be free of manufacturing defects

in material and workmanship for a period of two

years from date of purchase.

Some states do not allow the exclusion or

limitation of incidental or consequential

damages, so the above limitation may not apply

to you. This warranty gives you specific legal

rights, and you may also have other rights,

which vary from state to state.

This Warranty is subject to the following

additional conditions and limitations. The

Warranty is void and inapplicable if JOBSITE

deems that the product has been used or

handled other than in accordance with the

instructions provided by the manufacturer,

including, but not limited to, damage caused

by accident, mishandling, improper installation,

abuse, negligence, or normal wear and tear, or

any defect caused by repair to the product other

than by JOBSITE or an authorized JOBSITE

wholesale distributor.

For the name of the nearest authorized JOBSITE

wholesale distributor, contact:

JobSite Systems

12331 S.W. 130 Street, Miami, Florida 33186

WWW.JOBSITESYSTEMS.COM

DS00490ACN-0 LSS-10_12.indd

5/23/06

2:13:34 PM

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTES:

DS00490ACN-0 LSS-10_12.indd

5/23/06

2:13:34 PM

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTES:

DS00490ACN-0 LSS-10_12.indd

5/23/06

2:13:35 PM

Download from Www.Somanuals.com. All Manuals Search And Download.

JOBSITE SYSTEMS

12331 S.W. 130 STREET, MIAMI, FLORIDA 33186

P 866.4JB.SITE (866.452.7483) – F 305.238.0185

WWW.JOBSITESYSTEMS.COM

JobSite Logo is a trademark of Niles Audio Corporation. All other trademarks are the property of their respective owners. Some JobSite prod-

ucts (or components thereof) are manufactured under one or more U.S. Patents, foreign equivalents and/or pending patents (see product for

details). Because we constantly strive to improve our products, JobSite reserves the right to change product specifications, descriptions, and

prices without notice. The technical and other specifications of information contained herein are not intended to set forth all technical and

other specifications of JobSite products. Additional information can be obtained at WWW.JOBSITESYSTEMS.COM or by calling JobSite at

866.452.7483. DS00490ACN

DS00490ACN-0 LSS-10_12.indd

5/23/06

2:13:35 PM

Download from Www.Somanuals.com. All Manuals Search And Download.

InFocus Home Theater System QR80421 User Manual
Intel Security Camera NSC2U User Manual
Ironman Fitness Treadmill IRONMAN 120e User Manual
Jasco Speaker 98903 User Manual
Jenn Air Dishwasher JDB8910 User Manual
Jensen Car Stereo System JRV210 User Manual
Jet Tools Sander 22 44 Pro 3 User Manual
Kawasaki Motorized Toy Car C7478 User Manual
Kenmore Sewing Machine 38511703 User Manual
Kidde Smoke Alarm 820 1356 User Manual