5100
Regulatory models: W59
Download from Www.Somanuals.com. All Manuals Search And Download.
QR80421
WARNING: Do not look into laser beam emitted from the front of the
remote control.
CAUTION: Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation
exposure. Class 2 Laser product; maximum output 1mW; wavelength
650nm.
[Class 2 Laser Product] Wavelength 650nm; Maximum output 1mW; No
beam divergence.
IEC60825-1:2007 EN60825-1:2007
[Laser Diode] Wave length 650nm; Maximum power 7mW; Beam diver-
gence 33deg (perpendicular)/8deg (parallel).
OR
IEC60825-1:1993 +A1:1997 +A2:2001
Location of laser beam warning labels on remote
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Table of Contents
For complete details on connecting and operating the projector, refer to this
User’s Guide.
Connecting a computer
8
The website also has technical specifications (an interactive image size cal-
culator, laptop activation commands, connector pin outs, a glossary, the
product data sheet), a web store to buy accessories, and a page for online
registration.
33
Settings menu
42
Command Control
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Important Operating Considerations for Safety
•
Place the projector in a horizontal position no greater than 8 degrees off
axis.
•
Locate the projector in a well-ventilated area without any obstructions
to intake or exhaust vents. Do not place the projector on a tablecloth or
other soft covering that may block the vents.
/ 1 m
2’
3’
/ 0.6 m
•
Locate the projector at least 4' (1.2 m) away from any heating or cooling
vents.
m
5
.
8
’
/ 2
.
4
/ 1
m
’
5
•
•
Use only approved ceiling mounts.
Warning: To prevent eye injury if the projector is ceiling mounted,
wear protective eyewear before opening lamp door. A warning sticker
is included with the user documentation. Place this sticker on the lamp
door if the projector is mounted on the ceiling.
Follow these instructions to help ensure image quality and lamp life over
the life of the projector. Failure to follow these instructions may affect the
warranty. For complete details of the warranty, see the Warranty booklet.
•
•
Only genuine InFocus lamps are tested for use in this projector. InFo-
cus is not liable for the performance, safety or certification of any other
lamps. The use of other lamps violates the projector warranty and
voids all certification marks on this projector.
Use only the power cord provided. A surge-protected power strip is
recommended.
•
Refer to this manual for proper startup and shutdown procedures.
•
Hg – Lamp contains mercury. Manage in accordance with local
•
In the unlikely event of a lamp rupture, particles may exit through the
projector vents. When the projector is turned on, keep people, food,
and drinks out of the "keep out" area under and around the projector,
as indicated by the "X" areas.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Projector components and features: front
Introduction
Your new multimedia projector provides three computer, three video, and
four audio inputs, one audio output, and RS-232 and Network control. It
has WUXGA 1920 x 1200 resolution. The projector is easy to connect, easy to
use, and easy to maintain.
zoom/offset door
remote
control
receiver
Product specifications
To read the latest specifications on your multimedia projector, be sure to
visit our website. Web address information is located on the back inside
cover of this User’s Guide.
air intake
vent
heat vent
Online Registration
Register your projector on our website to receive product updates,
announcements, and registration incentives. See the inside back cover for
the web address.
elevator foot release
leveling foot
focus
Included Items
Projector components and features: back
lamp door
projector
remote
lens cap*
power cable
VGA computer cable
A/V cable
documentation
*The lens cap is tethered to the projector.
power switch
power plug
connectors
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Connector Panel
component video
remote
The projector provides three computer and three video connection options:
audio in 1,2
VGA computer
monitor
BNC
RJ-45
HDMI
USB
control
receiver
(IR)
•
•
•
one VGA computer
RS232
lock
serial control
one HDMI™ (High Definition Multimedia Interface)*
one component BNC (G/Y, B/C /P , R/C /P , H, V)
B
B
R
R
•
•
•
one component RCA video (Pr, Pb, Y)
one S-video
one composite RCA video
The projector provides computer and video connectors for audio support:
•
•
•
two composite RCA stereo audio (L, R)
one audio out
composite
audio in 3,4
power connector and switch
wired remote
s-video
video
external
speakers
(audio out)
two audio ins
speaker
The projector also provides the following connectors:
•
•
•
•
one wired remote
one monitor out
RS-232 serial connector (for serial control)
RJ-45 connector (for networked control)
The RS-232 Command Line Interface (CLI) specifications and commands
port.
* HDMI is an industry standard, uncompressed, all-digital audio/video
interface that connects between sources, such as set-top boxes, DVD play-
ers, and receivers and your projector. To take advantage of HDMI 1.3 you
must have a 1.3-compatible source. The HDMI, because it is a digital signal,
yields the highest quality image. It is common for these signals to be
encrypted with HDCP (high-bandwidth digital-content protection). Your
new projector ships standard with decryption codes so you can enjoy these
high quality, all digital images.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Positioning the projector
To determine where to position the projector, consider the size and shape of
your screen, the location of your power outlets, and the distance between
the projector and the rest of your equipment. Here are some general guide-
lines:
Projection angle in 16:10 mode (default)
10’ high image
10:0
1:1
•
Position the projector on a flat surface at a right angle to the screen. The
projector must be at least 3 feet (0.9m) from the projection screen.
lens center
•
Position the projector within 10 feet (3m) of your power source and
within 6 feet (1.8m) of your video device (unless you purchase exten-
sion cables). To ensure adequate cable access, do not place the projector
within 6 inches (.15m) of a wall or other object.
10:0
bottom of image
at lens center
•
•
•
•
If you are installing the projector on the ceiling, refer to the installation
guide that comes with the Ceiling Mount Kit for more information. To
using an authorized ceiling mount. The Ceiling Mount Kit is sold sepa-
rately; visit our website for more information.
1:1
bottom of image
50% below
lens center
Position the projector the desired distance from the screen. The dis-
tance from the lens of the projector to the screen, the zoom setting, and
the video format determine the size of the projected image. For infor-
mation about image sizes at different distances, see “Projected image
For the standard lens that comes with the projector, the image exits at a
given angle. However, the lens shift feature makes the image offset
variable. The image offset is 100% at a 10:1 ratio when the projector is in
16:10 mode (default mode). This means that if you have an image 10’
high, the bottom of the image will be at the center of the lens.
The image offset is 50% when the lens shift is at a 1:1 ratio. This means
that if you have an image 10’ high, the bottom of the image will be 5’
below the center of the lens.
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Connecting a computer
connect computer cable
Required computer connections
Connect one end of the VGA computer cable to the Computer 2 connector
on the projector. Connect the other end to the video port on your computer.
If you are using a desktop computer, you first need to disconnect the moni-
tor cable from the computer’s video port.
Connect the black power cable to the connector on the back of the projector
and to your electrical outlet.
connect power cable
NOTE: Always use the power cable that shipped with the projector.
Optional computer connections
You can also connect to your computer using optional BNC or HDMI
cables. Connect the BNC connectors on the BNC cable to the appropriate
Computer 3 connectors on the projector. Connect the other end to the video
port on your computer. If you are using a desktop computer, you first need
to disconnect the monitor cable from the computer’s video port.
Or, connect the HDMI cable to the Computer 1 connector.
connect BNC cable
connect HDMI cable
To have sound with your presentation, connect the audio cable to your
computer and to the corresponding computer Audio In connector on the pro-
jector. You can assign a particular source to a particular audio in connector,
connect audio cable
Download from Www.Somanuals.com. All Manuals Search And Download.
8
If you are using a desktop computer and want to see the image on your
computer screen as well as on the projection screen, plug the monitor cable
to the Monitor out connector on the projector.
connect monitor cable
connect RS-232 cable
You can control the projector from an LCD control panel, touch screen, or
other control device or computer by connecting an RS-232 cable to the pro-
jector’s Serial Control connector. Specific RS-232 commands can be found in
the Service and Support section of our website and in the Appendix.
The projector can be managed by networking software through its Network
(RJ-45) connector. Detailed instructions on this feature can be found on our
website.
connect CAT-5 cable
Network
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Displaying a computer image
Remove the lens cap.
remove lens cap
Press the power switch on the back of the projector to the on (I) position.
press Power switch press Power button
2
Press the Power button on the top of the projector or the remote.
The Power light blinks green and the fans start to run. When the lamp
comes on, the startup screen is displayed and the light is steady green. It can
take a minute for the image to achieve full brightness.
1
turn on computer
Turn on your computer.
The computer’s image should appear on the projection screen. If it doesn’t,
press the Source button on the keypad or remote.
activate laptop’s external port
Make sure your laptop’s external video port is active.
Many laptops do not automatically turn on their external video port when a
projector is connected. Usually a key combination like FN + F5 is used to
turn the external display on and off. Refer to your computer’s documenta-
tion to learn your computer’s key combination.
Download from Www.Somanuals.co1m0. All Manuals Search And Download.
Adjusting the image
release
button
adjust height
release
button
Adjust the height of the projector, if necessary, by pressing the release but-
tons on each side of the projector’s front to extend the elevator feet.
elevator
foot
elevator
foot
Position the projector the desired distance from the screen at a 90 degree
angle (perpendicular) to the screen.
adjust distance
Adjust the zoom by rotating the Zoom ring inside the lens door until the
desired image size is produced.
adjust zoom and focus
Adjust the focus by rotating the Focus ring on the lens until the desired
focus is produced.
adjust lens shift
If the image is not on the screen or viewing area, adjust it by using the lens
shift dials inside the lens door.
Use the right dial to shift the lens left or right. Use the left dial to shift the
lens up or down.
contrast
brightness
adjust Contrast or Brightness
Adjust the Contrast or Brightness in the Picture menu.
Download from Www.Somanuals.co1m1. All Manuals Search And Download.
Connecting a video device
Standard video connections
connect A/V cable
Plug the audio/video (A/V) cable’s yellow connector into the video-out
connector on the video device. Plug the other yellow connector into the yel-
low Video 3 connector on the projector. Plug a white connector into the left
audio out connector on the video device and plug a red connector into the
right audio out connector on the video device. Plug the remaining white
connector into a left audio in connector on the projector, and plug the red
connector into a right audio in connector on the projector. You can assign a
connect power cable
Connect the black power cable to the connector on the back of the projector
and to your electrical outlet.
NOTE: Always use the power cable that shipped with the projector.
Optional video connections
If the video device uses a round, four-prong S-video connector, plug an
S-video cable (sold separately) into the S-video connector on the video
device and into the Video 2 connector on the projector. Use the A/V cable’s
audio connectors as described directly above (the yellow connectors on the
A/V cable are not used).
connect S-video and video cables
If the video device uses component cable connectors (sold separately), plug
the cable’s green connectors into the green component-out connector on the
video device and into the Video 1 green component connector (labeled “Y”)
on the projector. Plug the component cable’s blue connectors into the blue
component-out connector on the video device and into the blue component
connector (labeled “Cb/Pb”) on the projector. Plug the component cable’s
red connectors into the red component-out connector on the video device
and into the red component connector (labeled “Cr/Pr”) on the projector.
Use the A/V cable’s audio connectors as described above (the yellow con-
nectors on the A/V cable are not used). NOTE: The component connectors
can be used for HDTV sources (480i, 480p, 720p, 576i and 1080i formats).
connect component cables
and video cables
Download from Www.Somanuals.co1m2. All Manuals Search And Download.
Displaying a video image
Remove the lens cap.
remove lens cap
Press the power switch on the back of the projector to the on (I) position.
press Power switch
press Power button
Press the Power button on the top of the projector or the remote.
2
The Power light blinks green and the fans start to run. When the lamp
comes on, the startup screen is displayed and the light is steady green. It can
take a minute for the image to achieve full brightness.
1
Plug in and turn on the video device.
turn on video device
The video device’s image should appear on the projection screen. If it
doesn’t, press the Source button on the keypad or remote.
adjust height
release
button
release
button
Adjust the height of the projector, if necessary, by pressing the release but-
tons on each side of the projector’s front to extend the elevator feet. Rotate
the feet, if necessary, to level the projector.
elevator
foot
elevator
foot
adjust distance
Position the projector the desired distance from the screen at a 90 degree
to the screen.
Download from Www.Somanuals.co1m3. All Manuals Search And Download.
Adjust the zoom by rotating the Zoom ring, located inside the lens door,
until the desired image size is produced.
adjust Zoom and Focus
Adjust the focus by rotating the Focus ring on the lens until the desired
focus is produced.
adjust Lens Shift
If the image is not on the screen or viewing area, adjust it by using the lens
shift dials inside the lens door.
Use the right dial to shift the lens left or right. Use the left dial to shift the
lens up or down.
adjust volume
Adjust the volume in the Audio menu.
adjust Picture menu
Adjust the Contrast, Brightness, Color, or Tint in the Picture menu.
Download from Www.Somanuals.co1m4. All Manuals Search And Download.
The Status Indicator Panel on top of the projector indicates the state of the
projector and can help you troubleshoot.
Shutting down the projector
The projector automatically blanks the screen after no active source is
detected for 5 minutes. This blank screen helps preserve the life of the pro-
jector. The image returns when an active source is detected or a remote or
keypad button is pressed.
Screen Save
Table 1: Status indicator light behavior and meaning
You can make the blank screen appear after five minutes by turning on
Status Indicator Panel icons
Power, solid green
Meaning
Power Save
The power button has been pressed and
the software has initialized or the projec-
tor has been powered off.
The projector also has a Power Save feature that automatically turns the
lamp off after no signals are detected for 20 minutes. After 10 additional
minutes with no signal, the projector powers down. If an active signal is
received before the projector powers down, the image is displayed. You
must press the Power button to display an image after 30 minutes have
Power, blinking green
Thermometer
The power button has been pressed and
the software is initializing, or the projec-
tor is powering down and the fans are
running to cool the lamp.
Turning off the projector
To turn off the projector, press the power button and verify that you want to
turn the projector off by pressing the power button again within 3 seconds.
You can cancel the shutdown by not pressing the power button a second
time. The lamp turns off and the Power light blinks green for over 1 minute
while the fans continue to run to cool the lamp. When the lamp has cooled,
the Power light is solid green and the fans stop. Press the power switch on
the back of the projector and unplug the power cable to completely power
off the projector.
The projector is too hot. Make sure the
off the projector and wait one minute,
then turn the projector on again. Contact
Technical Support if the problem persists.
Lamp
Turn off the projector and wait one min-
ute, then turn the projector on again. If
the lamp light turns on again, replace the
lamp and reset the lamp timer.
Troubleshooting your setup
If your image appears correctly on the screen, skip to the next section. If it
does not, troubleshoot the setup.
Wrench/Service
Turn off the projector and wait one min-
ute, then turn the projector on again. If
the service lamp turns on again, service is
required. Visit our website to contact Ser-
vice.
Download from Www.Somanuals.co1m5. All Manuals Search And Download.
Problem
Solution
Result
Plug power cable in, press power switch and
power button. Remove lens cap.
No startup screen
Correct image
3
startu
screen
p
2
1
Computer image projected
Only startup screen appears/no computer image
Press the Source button
Activate laptop’s external port
startu
screen
p
A
A
A
or restart
laptop
Download from Www.Somanuals.co1m6. All Manuals Search And Download.
Computer image projected
Adjust computer refresh rate in Control
Panel>Display>Settings>Advanced>
No computer image, just the words “Signal out of range”
Adapter (location varies by operating system)
Signal
range
out
of
A
A
A
You may also need to set a different
resolution on your computer, as shown
in the following problem, “Image fuzzy
or cropped”
Image clear and not cropped
Image fuzzy or cropped
Set your computer’s display resolution to the
native resolution of the projector
A
(Start>Settings>Control Panel>Display>Settings
tab, select1920x1200)
A
A
For a laptop,
disable laptop
monitor
or turn-on dual-
display mode
Download from Www.Somanuals.co1m7. All Manuals Search And Download.
Projector troubleshooting
Problem
Solution
Result
Square image
Image not square
Adjust keystone in the Picture menu
Correct image
Adjust the focus ring or Sharpness in the
Picture>Advanced menu
Image not sharp
A B
A B
Change aspect ratio to 16:9 in Picture>Aspect
ratio menu
Correct image
Image does not fit 16:9 screen
Download from Www.Somanuals.co1m8. All Manuals Search And Download.
Correct image
Turn on/off Ceiling in Settings>System menu
Image upside down
A
A B
A B
Image reversed left to right
Turn on/off Rear in Settings>System menu
Correct image
A
Correct image
Projected colors don’t match source
Adjust color, tint, color temperature, brightness,
contrast in the menus
COLOR
Download from Www.Somanuals.co1m9. All Manuals Search And Download.
Correct image
Move projector, adjust zoom or lens shift, adjust
height
Image not centered on screen
Adjust horizontal or vertical position in
Picture>Advanced menu
Still having problems?
This product is backed by a limited warranty. An extended warranty plan may be purchased from your dealer. When sending the projector in for repair, we
recommend shipping the unit in its original packing material, or having a professional packaging company pack the unit. Please insure your shipment for its
full value.
Download from Www.Somanuals.co2m1. All Manuals Search And Download.
LED
navigation buttons
Using the remote control
The remote uses two (2) AAA batteries (not included). They are easily
installed by sliding the cover off the remote's back, aligning the + and - ends
of the batteries, sliding them into place, and then replacing the cover.
laser
button
To operate, point the remote at the projection screen or at the projector (not
at the computer). The range of optimum operation is about 16 feet (5m). For
best results, aim the remote directly at the projector.
backlight button
source buttons
To use the laser pointer, press and hold the Laser button. The laser turns off
when the button is released, or times out after two (2) minutes of continu-
ous operation.
WARNING: Do not look into the laser beam emitted from the top of the
remote control.
The remote contains four Source buttons that allow you to assign a particu-
lar input to a specific source. Simply press the numbered Source buttons to
travel to whatever four sources you wish to have available.
Troubleshooting the remote
Press the remote's Menu button to open the projector's menu system. Use the
arrow buttons to navigate, and the Select button to select features and adjust
values in the menus.
•
Make sure the batteries are installed in the proper orientation and are
not dead. The LED at the top of the remote lights when any button is
pressed when the battery power is adequate.
•
Make sure you’re pointing the remote at the projector, not the com-
puter, and are within the remote range of 16 feet (5m).
The remote also has a power button to turn the projector on and off, volume
buttons and a mute button to control the sound, a backlight button to light
the remote's buttons in the dark, and a video and computer button to switch
between those two sources.
Two presentation-specific features are also provided. Use the blank button
to display a blank screen instead of the current slide; use the effect button to
invoke a user-definable action, such as freeze, or magnify.
The Auto Image button reacquires the computer image and the Presets but-
ton lets you customize the settings for each source. Up to three Preset set-
tings can be customized and saved.
Download from Www.Somanuals.co2m3. All Manuals Search And Download.
Using the audio
connect audio cable
To play sound from the projector, connect your source to an Audio In con-
nector on the projector.
Troubleshooting audio
If there is no sound, check the following:
•
•
•
•
Make sure the audio cable is connected.
Make sure mute isn’t active.
adjust volume
Make sure the volume is turned up enough.
Make sure you are connected to the corresponding audio in for your
source. By default, Audio 1 corresponds to Computer 2, Audio 2 corre-
sponds to Computer 3, Audio 3 corresponds to Video 2 and 3, and Audio
4 corresponds to Video 1. You can change these assignments, see
•
•
Adjust the audio source.
If playing a video, make sure the playback has not been paused.
external speakers
Connecting external speakers
The projector can be attached to external speakers that have their own
power source by plugging a speaker cable into the projector’s Audio Out
connector.
speaker
cable
Download from Www.Somanuals.co2m4. All Manuals Search And Download.
Optimizing computer images
Presentation features
After your computer is connected properly and the computer’s image is on
the screen, you can optimize the image using the onscreen menus. For gen-
Several features are provided to make giving presentation easier. The fol-
•
•
•
•
•
The Custom key, available on several optional remotes only, allows you
to assign various features to the key. The default effect is Source Info.
•
•
Adjust the Keystone, Contrast, or Brightness in the Picture menu.
Change the Aspect Ratio. Aspect Ratio is the ratio of the image width to
image height. Standard TV screens and older laptops are 4:3; HDTV
and most DVDs are 16:9; and widescreen computers are 16:10. Choose
The Freeze effect allows you to freeze the displayed image. This is use-
ful if you want to make changes on your computer without your audi-
ence seeing them.
•
•
Adjust the Color Temperature in the Advanced menu.
The Startup Logo menu option lets you change the default startup
screen to a black, white, blue, or a custom logo screen via Capture New.
Adjust the Phase, Tracking, or Horizontal or Vertical position in the
Advanced menu.
Two menu options, Power Save and Screen Save, are provided to auto-
matically shut down the projector after several minutes of inactivity or
•
Once you have optimized the image for a particular source, you can
save the settings using Presets. This allows you to quickly recall these
A Low Power menu option is also available to help lower the projec-
Download from Www.Somanuals.co2m5. All Manuals Search And Download.
Optimizing video images
Customizing the projector
After the video device is connected properly and the image is on the screen,
you can optimize the image using the onscreen menus. For general informa-
You can customize the projector for your specific setup and needs. See
•
•
For rear projection, turn Rear mode on in the Settings>System menu.
•
Adjust the Keystone, Contrast, Brightness, Color, or Tint in the Picture
For ceiling mounted projection, turn Ceiling mode on in the Set-
tings>System menu.
•
Change the Aspect ratio. Aspect ratio is the ratio of the image width to
image height. Standard TV screens and older laptops are 4:3; HDTV
and most DVDs are 16:9; and widescreen computers are 16:10. Choose
•
Specify which source the projector checks first for an active signal dur-
ing power-up.
•
•
•
•
•
Turn the projector’s on-screen display messages on and off.
Turn on power saving features.
•
•
Specify blank screen colors and startup logos.
Specify the menu language.
Adjust the Color Temperature. Select a listed value, or select User and
individually adjust the intensity of the red, green, and blue color. See
Download from Www.Somanuals.co2m6. All Manuals Search And Download.
Using the menus
To open the menus, press the menu button on the keypad or remote. (The
menus automatically close after 60 seconds if no buttons are pressed.) The
Main menu appears. Use the arrow buttons to move up and down to high-
light the desired submenu, then press the Select button.
Menu
button
To change a menu setting, highlight it, press Select, then use the up and
down arrow buttons to adjust the value, select an option using radio but-
tons, or turn the feature on or off using check boxes. Press Select to confirm
your changes. Use the arrows to navigate to another setting. When your
adjustments are complete, navigate to Previous, then press Select to go to
the previous menu; press the Menu button at any time to close the menus.
Keypad navigation
buttons
Main menu
Dots appear before the menu name. The number of dots indicate the menu’s
level, ranging from one (the Main menu) to five (the most nested menus).
Dots
The menus are grouped by usage:
•
•
The Picture menu provides image adjustments.
The Settings menu provides set-up type adjustments that are not
changed often.
•
The Source Info menu provides a read-only display of information
about the projector and source.
Settings
menu
Picture
menu
Certain menu items may be grayed out until a particular source is con-
nected. For example, Tint is only available for video sources and will be hid-
den when a computer source is active. Other menu items may be grayed out
when they are not available. For example, Brightness is grayed out until an
image is active.
Source Info menu
Download from Www.Somanuals.co2m7. All Manuals Search And Download.
Picture menu
To adjust the following six settings, highlight the setting, press Select, use
the up and down arrows to adjust the values, then press select to confirm
the changes.
Keystone Vertical
increasing keystone
decreasing keystone
Keystone Vertical: adjusts the image vertically and makes a squarer image by
using an adjustable scale band.
Keystone Horizontal: adjusts the image horizontally and makes a squarer
image by using an adjustable scale band.
Corner Correction: allows you to adjust the corners of the projected image.
This is particularly helpful when stacking projectors. Select the corner you
would like to adjust within the Corner Correction submenu and follow the
instructions on the screen to make desired adjustments.
Keystone Horizontal
Contrast: controls the degree of difference between the lightest and darkest
parts of the picture and changes the amount of black and white in the
image.
Brightness: changes the intensity of the image.
Color: (Computer 1 and video sources only) adjusts a video image from
black and white to fully saturated color.
Tint: (Computer 1 and NTSC video sources only) adjusts the red-green color
balance in the image.
Auto Image: resynchs the projector to the source.
Aspect Ratio: Aspect ratio is the ratio of the image width to image height.
Standard TV screens and older laptops are 4:3; HDTV and most DVDs are
16:9; and widescreen computers are 16:10. The default is 16:10, which dis-
plays the input resized up or down to fill the display area.
Corner Correction
Aspect Ratio
Download from Www.Somanuals.co2m8. All Manuals Search And Download.
Presets: Presets are provided that optimize the projector for displaying com-
puter presentations and video images in different lighting conditions and
on different backgrounds.
There are also user-definable presets. To set a preset for the current source,
adjust the image, select Save Settings in the Presets menu, then select Save
User Presets 1 (or 2 or 3). You can recall these settings in the future by select-
ing the User 1 preset. If you select User Presets then further adjust the
image, Presets Off will automatically be selected in the Preset menu to indi-
cate changes have been made.
Save Settings
To restore the factory default settings, choose Factory Reset in the Set-
tings>Service menu.
Presets
Advanced settings
Sharpness: changes the clarity of the edges of a video image. Select a sharp-
ness setting.
Color Space: This option applies to computer and component video sources
(except 480i/576i). It allows you to select a color space that has been specifi-
cally tuned for the input signal. When Auto is selected, the projector auto-
matically determines the standard. To choose a different setting, turn off
Auto, then choose RGB for computer sources, RGB Video for HDMI com-
puter sources, and either REC709 or REC601 for component video sources.
Sharpness
Advanced
Color Temperature: changes the intensity of the colors. Select a listed value,
or select User and individually adjust the intensity of the red, green, and
blue colors.
Color Space
Color Temperature
Download from Www.Somanuals.co2m9. All Manuals Search And Download.
Video Standard: when set to Auto, the projector attempts to automatically
pick the video standard based on the input signal it receives. (The video
standard options may vary depending on your region of the world.) If the
projector is unable to detect the correct standard, the colors may not look
right or the image may appear “torn.” If this happens, manually select a
video standard by selecting NTSC, PAL, or SECAM from the Video Stan-
dard menu.
On: Always display captions. Off: Never display captions. Channel: Selects
which captions to display.
.
Video Standard
Active Iris: when on, the projector monitors the image brightness and modi-
fies the light output if the image is dark, which improves black levels. In
Presentation mode, it looks at peak brightness, in Theater mode it looks at
average brightness.
Active Iris
Overscan: (Computer 1 and video sources only) removes noise around the
video image.
The following 4 options are for computer sources only:
Phase: adjusts the horizontal phase of computer 2, 3 and component (except
480i and 576i) sources.
Tracking: adjusts the horizontal scan of a computer source (except Computer
1).
Horizontal / Vertical Position: adjusts the position of a computer source
(except Computer 1) and Video 1 source (except 480i and 576i).
Resolution: When this feature is set to Auto, the projector attempts to pick
the resolution standard based on the input signal it receives. If the projector
is unable to detect the correct standard, the resolution may look odd. If this
happens, manually select the resolution from the menu which matches your
source signal.
Computer 2
Computer 3
Computer 2: allows you to turn Sync on Green on for this source.
Computer 3: allows you to turn Sync on Green on for this source.
Closed Captions: can be shown when the source is analog - component (480i
only), or S-video or composite (NTSC only). The video signal must also
include caption information. Auto: Display captions when sound is muted.
Download from Www.Somanuals.co3m0. All Manuals Search And Download.
Split Screen
Split Screen lets you show two different sources at the same time, one on the left half of the screen and the other on the right. The following source combina-
tions are supported:
Table 2: Split Screen Matrix
Computer 1
Computer 2
X
Computer 3
Video 1
Video 2
Video 3
Computer 1
Computer 2
Computer 3
Video 1
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Video 2
X
X
Video 3
Download from Www.Somanuals.co3m1. All Manuals Search And Download.
Exit or Previous: Removes the Split Screen Menu (if Split Screen is on) or goes
to the Picture menu (if Split Screen is off).
Most picture settings can’t be adjusted (e.g. Brightness, Contrast, Keystone,
Overscan, Presets, etc.).
Split Screen: Check the box to turn on Split Screen, or un-check it to turn off
To change these settings:
Split Screen.
Make sure the source you want to adjust is the main source (See above for a
description of the main source. If needed, go to the Split Screen Menu and
select Swap Left and Right or Main on Left/Right).
Main on Left/Right: Selects which side is the main (primary) side. Characteris-
tics of the main side:
Source buttons, as well as Aspect Ratio and Auto Image buttons, affect the
main side only (unsupported source combinations are prevented – see
above table).
Turn off Split Screen (go to the Split Screen Menu, then select Main Menu,
or un-check Split Screen then select Previous).
Change picture settings.
Only sound from the main side is audible.
Turn on Split Screen (go to the Split Screen Menu, then check Split Screen).
When Split Screen is turned off, the main side is displayed full screen.
Swap Left and Right: Switches the left and right sources.
Some RS-232 commands have no effect. See the end of the RS-232 Com-
mand Additions section later in this document.
Left/Right Settings: Adjusts aspect ratio, phase, tracking, and horizontal/ver-
tical position for the left or right side.
Left/Right Source: Selects the source to display on the left or right side (some
items will be disabled to prevent unsupported source combinations – see
above table).
Split Screen Menu
Source Info: Shows source information for the left and right sides.
Main Menu: Turns off Split Screen and goes to the Main Menu.
To program your remote’s Custom button to display the above Split Screen
Menu: Go to the Main Menu > Settings > Custom Key menu and select Split
Screen.
IMPORTANT - When Split Screen is on, some projector functions work dif-
ferently:
The Main Menu and its sub-menus are not available – pressing the Menu
button shows the Split Screen Menu instead. To turn off Split Screen and
access other menus from the Split Screen Menu: select Main Menu, or un-
check Split Screen then select Previous.
Autosource (source search), Closed Captions and Magnify are not available.
Download from Www.Somanuals.co3m2. All Manuals Search And Download.
Auto Power: When Auto Power is checked, the projector automatically
goes into the startup state after the projector is powered on. This allows
control of ceiling mounted projectors with a wall power switch.
Settings menu
Audio: allows adjustments to the volume. Also allows you to turn on and off
the Internal speakers and assign a particular source to a specific audio
input. If your HDMI source has problems with its audio stream, you can
mute it by selecting HDMI Noise Cancel.
Display Messages: displays status messages (such as “Searching”) in the
lower-left corner of the screen.
Monitor Out Default: Determines the source (either Computer 2 or Computer
3) which is output through the Monitor Out connector. Computer 2: Out-
puts Computer 2 unless current source is Computer 3 (in that case output
Computer 3 instead). Computer 3: Outputs Computer 3 unless current
source is Computer 2 (in that case output Computer 2 instead). Off: Outputs
the current source if it is Computer 2 or Computer 3. Otherwise do not out-
put any signal.
Settings
menu
Audio
Sources: allows you to assign a particular input to a specific source key
when using the remote. Also allows selection of a default Startup Source
and enables or disables Autosource.
Sources>Power-up Source: this determines which source the projector checks
first for active signal during power-up.
Sources>Autosource: When Autosource is not checked, the projector defaults
to the source selected in Powerup Source. If no source is found, a blank
screen displays. When Autosource is checked, Powerup Source determines
which source the projector defaults to at power-up. If no signal is present,
the projector checks the sources in order until a source is found or until
power down.
Powerup
Source
Sources
System>Rear: reverses the image so you can project from behind a trans-
lucent screen.
Ceiling: turns the image upside down for ceiling-mounted projection.
WARNING: To prevent eye injury if the projector is ceiling mounted,
wear protective eyewear before opening lamp door. A warning sticker is
included with the user documentation. Place this sticker on the lamp
door if the projector is mounted on the ceiling.
IR Receivers: turns individual IR receivers off or on to avoid environmen-
tal interference.
IR Receivers
System
Download from Www.Somanuals.co3m3. All Manuals Search And Download.
Low Power: toggles between on and off. Turn it on to lower the light out-
put of the lamp. This also lowers the fan speed, making the projector qui-
eter.
on Black: Horizontal lines on a black background. Grid on White: Grid
on a white background. Grid on Black: Grid on a black background.
PC Screen Saver Off: prevents your notebook computer from going into
Screen Save mode. The projector must be connected to the PC via a USB
cable for this feature to work.
Screen Save
Power Save: automatically turns the lamp off after no signals are detected
for 20 minutes. After 10 additional minutes with no signal, the projector
powers down. If an active signal is received before the projector powers
down, the image will be displayed.
Screen Save: automatically blanks the screen after no signals are detected
for five minutes. The image returns when an active source is detected or
a remote or keypad button is pressed. Screen Save is disabled when
Power Save is enabled.
Startup Logo: allows you to display a blank Black, White, or Blue screen
instead of the default screen when no source is detected at startup. It also
allows you to capture and display a custom startup screen.
Capture New
Startup Logo
To capture a custom logo, display the image you want to capture on
your computer and select the Capture New option. From the Capture
New menu, use the Capture Position X and Capture Position Y adjust-
ments to frame the logo to be captured. Press Capture Start in the Cap-
ture New menu. The projector will let you know if the capture was a
success or a failure.
Blank Screen
Ruled Lines
The next time you start the projector, the custom logo you captured dis-
plays.
Blank Screen: determines what color is displayed when you press the
Blank button on an optional remote.
Ruled Lines: This feature displays line patterns that are useful when pro-
jecting onto a writeable surface, or when installing and setting up the
projector. Lines on White: Horizontal lines on a white background. Lines
Download from Www.Somanuals.co3m4. All Manuals Search And Download.
Custom Key (for use with optional remote only): allows you to assign a dif-
ferent function to the Custom key on the optional remote to quickly and eas-
ily use the effect. Only one effect can be enabled at a time. The default is
Source Info; highlight an effect and press Select to choose a different one.
IP Address: Identifies the projector on the network.
Subnet Mask: Separates the network address part of the IP address.
Default Gateway: The IP address of the local router.
DNS Server: Shows the address of the DNS server.
Blank: shows an empty screen.
Mute: turns off all sound.
DHCP: Select this to automatically obtain an IP address, Subnet mask,
and Default gateway.
AV Mute: turns off all sound and displays a blank screen.
Aspect Ratio: sets the ratio of the image width to image height.
Source: cycles through the available sources.
Auto Image: causes all sources to be reacquired.
Freeze: pauses the projected image.
AMX DD: When enabled, allows the AMX controller to dynamically
detect the projector.
Network Restart: Disconnects the projector from the network, gets a
new IP address, and reconnects.
Network Info: Provides information on the network configuration.
Magnify: allows you to enlarge a section of the projected image.
Ruled Lines: displays line patterns that are useful when projecting onto a
writeable surface, or when installing and setting up the projector.
Network
Split Screen: enables or disables Split Screen. Before using this for the
first time, configure Split Screen sources and layouts using the Split
Screen menu.
Source Info: displays the Source Info menu.
Service Info: displays the Service Info menu.
Network Info
Network: The projector has an RJ45 Ethernet connector that supports net-
work connections and TCP/IP protocols. This will allow for the control and
management of the projector over a corporate network. Visit our website for
complete details on using the networking functionality. The following fields
are accessible when DHCP is not checked and available for manual entry of
data.
For network control, you can access the projector through Port 23 (Telnet).
We use the same control codes on serial as we do over the network. InFocus
network control uses the Telnet packet structure.
Download from Www.Somanuals.co3m5. All Manuals Search And Download.
Language: allows you to select a language for the onscreen display of menus
and messages.
Language
Service: to use these features, highlight them and press Select.
Factory Reset: restores all settings (except Lamp and Filter Hours and Net-
work settings) to their default after displaying a confirmation dialog box.
Reset Lamp Hours: resets the lamp hours counter in the Service Info menu to
zero. Do this only after changing the lamp. It displays a confirmation dialog
box.
Reset Filter Hours: resets the filter counter in the Service Info menu to zero.
Do this only after cleaning the filter. It displays a confirmation dialog box.
Service Info: provides information for service.
Service Code: only used by authorized service personnel.
Service menu
Service Info
Download from Www.Somanuals.co3m6. All Manuals Search And Download.
Maintenance
clean the lens
with a soft dry cloth
and non-abrasive
cleaner
Cleaning the lens
1 Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
Avoid using an excessive amount of cleaner, and don’t apply the
cleaner directly to the lens. Abrasive cleaners, solvents or other harsh
chemicals might scratch the lens.
2 Lightly wipe the cleaning cloth over the lens in a circular motion. If you
don’t intend to use the projector immediately, replace the lens cap.
Download from Www.Somanuals.co3m7. All Manuals Search And Download.
hands after lamp replacement.
Hg – Lamp contains mercury. Manage in accordance with local
Replacing the projection lamp
The lamp hour timer in the Service Info menu counts the number of hours
the lamp has been in use. Twenty hours before the specified end of the
lamp’s life, the message “Change lamp” briefly appears on the projected
screen.
Service Info menu
areas), your retailer or your dealer. Only genuine InFocus lamps are tested
for use in this projector. InFocus is not liable for the performance, safety or
certification of any other lamps. The use of other lamps violates the projec-
tor warranty and voids all certification marks on this projector.
1 Turn off the projector and unplug the power cable.
turn off and unplug
the projector
2 Wait 45 minutes to allow the projector to cool thoroughly.
3 Loosen the lamp cover screw on the right side of the projector (marked
by the arrow) then slide and lift the lamp cover off.
wait 45 minutes
WARNINGS:
•
•
•
To avoid burns, allow the projector to cool for at least 45 minutes before
you replace the lamp.
Only genuine InFocus lamps are tested with this projector. Use of other
lamps may cause electrical shock and fire.
To prevent eye injury if the projector is ceiling mounted, wear protec-
tive eyewear before opening lamp door. A warning sticker is included
with the user documentation. Place this sticker on the lamp door if the
projector is mounted on the ceiling.
•
•
Do not drop the lamp module. The glass may shatter and cause injury.
Do not touch the glass lamp screen. Fingerprints can obscure projection
sharpness.
lamp cover screw
Be extremely careful when removing the lamp housing. In the unlikely
event that the bulb ruptures, small glass fragments may be generated.
The lamp housing is designed to contain these fragments, but use cau-
tion when removing the lamp housing. Before replacing the lamp,
clean the lamp compartment and dispose oDfocwlnelaonadinfgrommaWtwerwia.Slso.mWanausahls.co3m8. All Manuals Search And Download.
4 Loosen the three captive screws (marked by the arrows) on the lamp
module. When replacing the lamp, never touch any screws without the
arrow mark.
loosen the captive screws on lamp module
5 Carefully remove the lamp module by grasping and lifting the handle.
lamp module handle
Dispose of the lamp in an environmentally proper manner.
6 Install the new lamp module, making sure that it is properly seated, and
tighten the three captive screws.
7 Replace the cover over the lamp module by sliding it back into place and
tightening the screw.
8 Plug in the power cable, press the power switch then press the Power
button to turn the projector back on. Reset the lamp hour timer by navi-
gating to the Settings>Service menu and selecting Reset Lamp Hours.
reset lamp hours in Service menu
Download from Www.Somanuals.co3m9. All Manuals Search And Download.
Cleaning the dust filter
1 Turn off the projector and unplug the power cable.
2 Wait 45 minutes to allow the projector to cool thoroughly.
WARNING: To avoid burns, allow the projector to cool for at least 45
minutes before you clean or replace the dust filter.
wait 45 minutes
3 Remove the dust filter cover on the side of the projector by pressing up
on the two tabs at the cover’s bottom.
4 Pull the tab on the center of the black dust filter bracket and lift it off.
5 Clean the filter, cover, and vent using a vacuum set on low power.
Replace the filter if it is damaged or too dirty to clean.
6 Replace the dust filter and the bracket on the cover, then replace the
dust filter cover.
7 Reset the filter hour timer by navigating to the Settings>Service menu
and selecting Reset Filter Hours.
dust filter cover
tabs
reset filter hours in Service menu
Using the security lock
The projector has a security lock for use with a cable lock system. See the
Accessories catalog that came with the projector, or visit our website, for
ordering information. Refer to the information that came with the lock for
instructions on how to use it.
security lock
Download from Www.Somanuals.co4m0. All Manuals Search And Download.
Appendix
Projected image size
NOTE: Visit the Service section of our website for interactive image size cal-
culators for the standard lense.
Table 3: Projection sizes: Standard lens (1.5 - 2.9:1 throw ratio)
Minimum Image
Maximum Image
Diagonal
Image
Image
Width
Diagonal
Image
Image Width
(feet/m)
Distance (feet/m)
(feet/m)
(feet/m)
(feet/m)
Min Distance
3/0.9
not
supported
not
supported
2.5/0.8
2.1/0.7
5/1.5
not
not
4.1/1.3
3.5/1.1
supported
supported
6/1.9
10/3.0
15/4.6
20/6.1
25/7.6
2.5/0.8
4.0/1.2
6.0/1.8
8.0/2.4
10.0/3.1
12.0/3.7
2.1/0.6
3.4/1.0
5.1/1.6
6.8/2.1
8.5/2.6
10.2/3.1
5.0/1.5
8.1/2.5
4.2/1.3
6.8/2.1
12.0/3.7
16.0/4.9
19.9/6.1
23.9/7.3
10.2/3.1
13.5/4.1
16.9/5.2
20.3/6.2
30/9.1
37/11.2
14.7/4.5
29.2/8.9
12.4/3.8
24.7/7.5
29.2/8.9
24.7/7.5
Max Distance
73/22.3
not
supported
not
supported
The image offset range for the standard lens is 10:0 (100%) to 1:1 (50%).
Download from Www.Somanuals.co4m1. All Manuals Search And Download.
(starts the command
Command Control
AAA denotes the command
Serial Communication Configuration
Visit our website for additional RS-232 settings and information.
? denotes the read request
To control this projector via RS-232, connect a null modem cable and set the
control system serial port settings to match the following communication
configuration:
) ends the command
A read command returns the range and the current setting, for example:
RS-232 Port Settings
Read Command Examples
Setting
Value
19,200
8
Function
Command
(BRT?)
Response
Bits per second
Data bits
Parity
Brightness
Volume
(96-160,128)
(0-32,16)
(VOL?)
(LMP?)
None
1
Lamp Hours
(0-32766, 42)
Stop bits
A write request example:
(AAA####) where
Flow control
Emulation
None
VT100
(starts the command
AAA denotes the command
#### denotes the value to be written
(leading zeros not necessary)
) ends the command
Network Communication Configuration
For network control, you can access the projector through Port 23 (Telnet).
We use the same control codes on serial as we do over the network. InFocus
network control uses the Telnet packet structure.
Command Format
Some commands have ranges, while others are absolute. If a number
greater than the maximum range is received, it is automatically set to the
maximum number for that function. If a command is received that is not
understood, a "?" is returned. With absolute settings, "0" is off, 1-9999 is on.
The one exception is the Power command, where 0 is off and 1 is on.
All commands consist of 3 alpha characters followed by a request, all
enclosed in parentheses. The request can be a read request (indicated by a
"?") or a write request (indicated by 1 to 4 ASCII digits).
A read request example:
To assure the projector can process a command, wait 3 seconds before enter-
ing the next command.
(AAA?) where
Download from Www.Somanuals.co4m2. All Manuals Search And Download.
Com
mand
Write Command Examples
Function
RW Min
Max
2
Default
1
Step
1
Function
Brightness
Power
Command
(BRT100)
(PWR0)
Response
Active Iris*
0: Off
1: Presentation
2: Film
IRI
RW
0
Sets the brightness to 100
Turns power off
Power
(PWR1)
Turns power on
AMX Device Discov-
ery Enable
0: Disable; 1: Enable
AMX
ARZ
RW
RW
0
0
1
6
0
0
1
1
Error Conditions
Not all commands are supported for all projectors. If an unsupported com-
mand is issued, the command will be ignored. If a command is received that
is not understood, a ‘?’ character will be returned indicating the command
was not understood.
Aspect Ratio
0: Auto
1: Native
2: 4:3
Limitations
3: 16:9
6: 16:10
The projector cannot respond to commands coming in at a high-rate. There-
fore, a delay must occur between commands to ensure that the command
gets properly executed.
Aspect Ratio (Split
Screen left)
0: Auto
ARL
ARR
RW
RW
0
0
6
6
0
0
1
1
1: Native
2: 4:3
3: 16:9
The Step column refers to increasing or decreasing the menu bar position
since the On-screen Display is not an exact match of values. For example,
Step 2 changes the data by 2 through the CLI (Command Line Interface).
The menu bar is up (or down) by 1.
6: 16:10
Aspect Ratio (Split
Screen right)
0: Auto
1: Native
2: 4:3
3: 16:9
6: 16:10
Download from Www.Somanuals.co4m3. All Manuals Search And Download.
Auto Image
1: enable
AIM
APO
ASC
BLK
BSC
W
n/a
0
1
1
1
1
2
n/a
0
1
1
1
1
1
Color*
CLR
CSM
RW 96
160
4
128
0
1
1
Color Space*
0: Auto
1: RGB
2: REC709
3: REC601
4: RGB Video
RW
0
Auto Power*
0: disable; 1: enable
RW
RW
RW
RW
Auto Source*
0: disable; 1: enable
0
1
Blank
0: disable; 1: enable
0
0
Color Temp*
0: 9300K
1: 6500K
2: 7200K
3: User
TMP
RW
0
3
1
2 (computer2,
3)
0 (computer1,
video)
Blank Screen*
0: black
1: blue
0
1
2: white
Contrast*
CON RW 96
160
1
128
0
1
1
Brightness*
BRT
CEL
RW 96
160
1
128
0
1
1
Corner Correction
Enable*
0: Disable; 1: Enable
CNE
RW
0
Ceiling*
0: disable; 1: enable
RW
0
Corner Correction-
Top left corner -H*
CN1
CN2
CN3
CN4
CN5
RW
RW
RW
RW
RW
0
0
0
0
0
959
599
959
599
959
0
0
0
0
0
1
1
1
1
1
Closed Captions*
0: Off
1: On
CCD
RW
0
2
0
1
Corner Correction-
Top left corner -V*
2: Auto
Closed Captions
Channel*
0: CC1
1: CC2
2: CC3
CCC
RW
0
7
0
1
Corner Correction-
Top right corner -H*
Corner Correction-
Top right corner -V*
3: CC4
Corner Correction-
Bottom left corner -
H*
4: Text1
5: Text2
6: Text3
7: Text4
Download from Www.Somanuals.co4m4. All Manuals Search And Download.
Corner Correction-
Bottom left corner -
V*
CN6
CN7
CN8
CNR
RW
RW
RW
RW
0
0
0
0
599
959
599
1
0
1
1
1
1
Custom Key (Effect)*
0: Blank
1: Mute
2: Aspect ratio
3: Source
4: Auto image
5: Freeze
EFK
RW
0
18
7
1
Corner Correction-
Bottom right corner -
H*
0
6: Magnify
Corner Correction-
Bottom right corner -
V*
0
7: Source Info
8: Service Info
15: AV Mute
17: Split Screen
18: Ruled Lines
n/a
Corner Correction all
corners Reset*
0: n/a
1: enable
Display Messages*
0: disable; 1: enable
DMG RW
0
1
1
1
1
1
Source
SRC
RW
0
5
0
1
Factory Reset*
1: reset
RST
W
n/a
n/a
0: computer1
1: computer2
2: computer 3
3: video 1
4: video 2
5: video 3
Filter Hours
RFT
FRZ
R
0
0
32766
1
0
0
Freeze
0: disable; 1: enable
RW
1
1
HDMI Noise Cancel*
0: Not Reset
1: Reset
HNC RW
0
1
1
Horizontal Keystone*
Horizontal Position
DKH
HPS
RW 88
168
128
1
1
RW Def.
-128
Def.
+128
auto
Horizontal Position
(Split Screen left)
HPL
RW Def.
-128
Def.
+128
auto
1
Download from Www.Somanuals.co4m5. All Manuals Search And Download.
Horizontal Position
(Split Screen right)
HPR
INT
RW Def.
-128
Def.
+128
auto
1
1
1
Language*
0 = English
1 = French
2 = German
3 = Italian
LAN
RW
0
17
0
1
Internal Sound
Enable*
0: disable; 1: enable
RW
0
1
5 = Korean
6 = Norwegian
7 = Portuguese
8 = Russian
9 = Simp. Chinese
10 = Spanish
11 = Trad. Chinese
12 = Swedish
13 = Dutch
IP Address Byte 1
IP Address Byte 2
IP Address Byte 3
IP Address Byte 4
IP1
IP2
IP3
IP4
IRF
R
0
0
0
0
0
1
1
1
1
1
192
168
1
R
R
R
254
1
IR Receiver front*
0: disable; 1: enable
RW
1
1
1
14 = Polish
15 = Turkish
16 = Danish
17 = Finnish
IR Receiver rear*
0: disable; 1: enable
IRR
IRT
RW
RW
0
0
1
1
1
0
Lamp Hours Used: All
Bulbs
LMT
R
0
21474
83646
0
IR Receiver top*
0: disable; 1: enable
Lamp Hours
LMP
LB1
LB2
LB3
LML
R
R
R
R
R
0
0
0
0
0
32766
32766
32766
32766
1
0
Lamp 1 Lasted (Hrs)
Lamp 2 Lasted (Hrs)
Lamp 3 Lasted (Hrs)
0
0
0
Lamp Lit
n/a
0: not lit; 1: lit
Lamp Resets (Total)
LMR
LPE
R
0
0
32766
1
0
0
Low Power*
RW
1
0: disable; 1: enable
Download from Www.Somanuals.co4m6. All Manuals Search And Download.
Magnify*
MAG RW
0
0
48
1
0
0
1
1
Phase (Split Screen
left)
MSL
RW
RW
RW
0
0
0
31
31
1
0
0
0
1
1
1
Magnify Enable*
0: disable; 1: enable
MGE
RW
RW
RW
Phase (Split Screen
right)
MSR
PWR
Magnify Position Hori- MPH
zontal*
0
0
0
0
64
64
1
32
32
0
1
1
1
1
Power
0: Turn Off; 1: Turn
On
Magnify Position Ver-
tical*
MPV
Power Save*
0: disable; 1: enable
PSV
RW
RW
0
0
1
5
0
0
1
1
Menu
0: clear; 1: display
MNU RW
Power-up Source*
0: computer 1
1: computer 2
2: computer 3
3: video 1
DSC
Menu Navigation
0: up key
1: down key
4: select key
NAV
W
4
n/a
4: video 2
5: video 3
Monitor Out Default* MO
RW
1
5
1
1
1: Computer 2
2: Computer 3
5: Off
D
Presets*
0: user 1
PST
RW
0
11
1
5 (computer
2, 3)
1: user 2
2: user 3
3: Presets Off
5: presentation
7: video
7 (computer1,
video)
Mute
0: disable; 1: enable
MTE
NTR
OVS
RW
W
0
1
0
1
1
1
1
1
Network Restart*
1: restart
n/a
0
1
n/a
0
10: bright
11: whiteboard
Overscan*
0: disable; 1: enable
RW
1
Rear*
0: disable; 1: enable
REA
FRT
RW
W
0
1
1
0
1
1
PC Screen Saver Off*
0: disable; 1: enable
NND RW
0
1
1
Reset Filter Hours
1: reset
n/a
n/a
Phase
MSS
RW
0
31
0
Download from Www.Somanuals.co4m7. All Manuals Search And Download.
Reset Lamp Hours
1: reset
LRT
RLL
W
n/a
0
1
3
n/a
0
1
1
Source 0 Audio*
0: audio 1
1: audio 2
2: audio 3
3: audio 4
SA0
SAn
RW
RW
0
0
5
5
4
1
1
Ruled Lines*
RW
0: Lines on White
1: Lines on Black
2: Grid on White
3: Grid on Black
4: HDMI Internal
5: mute
Source 1-5 Audio*
0: audio 1
1: audio 2
2: audio 3
3: audio 4
Source 1=
0
Source 2=
1
Source 3 =
3
Source 4 =
Ruled Lines Enable
0: disable; 1: enable
RLE
USn
RW
W
0
1
1
0
1
1
Save User Presets 1-
3*
1: save
n/a
n/a
5: mute
2
Screen Save*
0: 5 minutes
1: 10 minutes
2: 15 minutes
3: 20 minutes
4: 25 minutes
5: 30 minutes
SSV
RW
0
5
5
0
1
Source 5 =
2
Source 1*
SR1
SR2
RW
RW
0
0
5
5
0
1
1
1
0: computer 1
1: computer 2
2: computer 3
3: video 1
4: video 2
5: video 3
Sharpness*
5 = Sharpest
6 = Sharper
7 = Standard
8 = Softer
SHP
RW
9
1
7 (computer
and video 1)
6 (video 2
and 3)
Source 2*
0: computer 1
1: computer 2
2: computer 3
3: video 1
9 = Softest
4: video 2
5: video 3
Download from Www.Somanuals.co4m8. All Manuals Search And Download.
Source 3*
SR3
SR4
RW
RW
0
0
5
5
3
4
1
1
Split Screen Right
Source
0: Computer 1
1: Computer 2
2: Computer 3
3: Video 1
SSR
RW
0
5
2
1
0: computer 1
1: computer 2
2: computer 3
3: video 1
4: video 2
5: video 3
4: Video 2
5: Video 3
Source 4*
0: computer 1
1: computer 2
2: computer 3
3: video 1
4: video 2
5: video 3
Split Screen Swap Left
and Right
1: Execute Swap
SSS
W
n/a
0
1
2
n/a
1
1
1
Startup Logo*
0: blank screen
1: default
DSU
RW
Source Info
1: enable
ABT
SSC
SSM
SSL
W
n/a
0
1
1
1
5
n/a
0
1
1
1
1
2: captured
Sync on Green*
0: Disable; 1: Enable
SOG
RW
0
1
1
1
Split Screen
0: Disable; 1: Enable
RW
RW
RW
Tint*
TNT
MTS
RW 96
160
128
1
1
Split Screen Main Side
0: Left; 1: Right
0
0
Tracking
RW def.
-384
def.
+384
auto
Split Screen Left
Source
0: Computer 1
1: Computer 2
2: Computer 3
3: Video 1
0
1
Tracking (Split Screen
left)
MTL
MTR
ONL
DKC
RW def.
-384
def.
+384
auto
auto
0
1
1
Tracking (Split Screen
right)
RW def.
-384
def.
+384
4: Video 2
5: Video 3
Unit Total Time On
R
0
21474
83646
Vertical Keystone*
RW 48
208
128
1
Download from Www.Somanuals.co4m9. All Manuals Search And Download.
Vertical Position
VPS
VPL
VPR
RW if
def<1
def+
128
auto
auto
auto
0
1
1
1
1
28 : 0
else:
def-
128
Vertical Position (Split
Screen left)
RW if
def+
128
def<1
28 : 0
else:
def-
128
Vertical Position (Split
Screen right)
RW if
def+
128
def<1
28 : 0
else:
def-
128
Video Standard*
0: Auto
1: NTSC
2: PAL
3: SECAM
VSU
VOL
RW
RW
0
3
Volume
0
32
16
1
1
Red Gain*
Green Gain*
Blue Gain*
RCG
GCG
BCG
RW 64
192
128
* These RS-232 commands have no effect when Split Screen is on.
Download from Www.Somanuals.co5m0. All Manuals Search And Download.
INDEX
displaying
Numerics
A
E
Aspect Ratio 28
F
B
focus 11, 14
H
C
I
computer connections
image
L
computer image
D
Language 36
laptop
Display Messages 33
Download from Www.Somanuals.co5m1. All Manuals Search And Download.
Low Power 34
M
RS-232
S
screen saver, turning off 34
N
Settings menu 33
Network Info 35
O
P
T
PC Screen Saver Off 34
projector
V
video image
video images
W
X
R
Z
zoom 11, 14
Download from Www.Somanuals.co5m2. All Manuals Search And Download.
|
