JPS-10: 10" PROSHOP 1-3/4HP 30"- CW
The JET ProShop 10" Table Saw (#708482K) is the
result of combining key cabinet saw features with the
semi open leg structure of the venerable contractor-
style table saw. While developing a unique set of
technologies to give the JET ProShop 10" Table Saw
wide-ranging capabilities was the goal, accuracy,
durability and ease of use remained at the top of the
priority list throughout the design process.
The new JET JPS-10 ProShop saw
represents new thinking that
makes your shop time more
This new design also allowed simplifying the assembly
process considerably. With the motor installed within
the cabinet at the factory, the process of hanging the
motor on an external bracket and aligning it with the
accurate and productive.
arbor, common on contractor-style saws is eliminated completely. The extended
cabinet of the JET ProShop 10" Table Saw also replaces the open leg assembly
common contractor saws with four channel-shaped legs that are extremely rigid and
very easy to install. Four bolts secure each leg to the cabinet and need only to have
the leveling feet attached to get the JET ProShop 10" Table Saw upright and ready
for final assembly.
At the heart of the JET ProShop 10" Table Saw is the all-new operating mechanism
that locates the motor inside of the cabinet. This massive cast iron mechanism is
extraordinarily rigid and substantially increases the vibration dampening mass
directly below the
table. The result is
super smooth, super
quiet operation with
an overall stability of
the blade system
previously found
only in machines
that are far more
expensive.
The all-new ProShop mechanism (left) not only moves the motor inside of
the cabinet but also uses a heavy-duty swing arm (right) to locate the
arbor. This system drastically reduces vibration and makes blade height
A dual drive belt
system transfers
changes smooth and precise.
motor power to the
5/8”-diameter arbor that is located in a short, super rigid cast iron arm. Blade height
adjustments are remarkably smooth in part because the blade arm is isolated from
the weight of the motor and undercarriage. The 5/8”-diameter arbor was designed
with sufficient length to handle most stacked 6” or 8”-diameter dado sets at a full
13/16” width.
The blade height and tilt mechanism provides maximum cut depths of 3 1/8” at 0-
degrees and 2 1/8” at 45-degrees. The mechanism tilts the blade to the left, away
from the fence so the operator is controlling the major piece and the scrap falls onto
the table, away from the blade.
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the fence for
exact cut widths is
easy thanks to a
magnifying cursor
that is built into the
T-square base. The
cursor is adjustable
side-to-side to
insure maximum
precision after the
fence is installed and
aligned.
The new ProShop T-square style fence (left) is rigid and very accurate. A
large scale and adjustable, magnified cursor (right) make setting precise
cuts simple.
The fence system is
supported front and
back on heavy steel rails and guide tube. An adjustable height pad at the rear of the
fence allows it to glide across the table smoothly. The pure strength of this mounting
system creates a stable, permanent base that insures accuracy and easy of use for
decades.
The 20” by 27” cast iron table surface is precision ground to insure it is perfectly flat.
The useable surface expands to 44” by 27” with the extension wings. The JET
ProShop 10" Table
Saw is available with
heavy-duty steel or
precision-ground
cast iron extension
wings. A pair of T-
style miter slots are
precision milled into
the table surface.
The ¾”-wide by
3/8”-deep miter
slots accept all
common table saw
accessories.
The ProShop Saw comes with a quality, angle-adjustable miter gauge (left)
and features an adjustable-width guide bar (right) to insure a perfect fit to
the slot for maximum accuracy.
A fully adjustable miter gauge comes with the JET ProShop 10" Table Saw. The guide
bar features a removable T-slot follower and width adjusters to eliminate side play
for super-stable cuts. The head can be set to any angle from 0 to 60-degrees left or
right with adjustable stops at 0 and 45-degrees, also on both sides of zero.
Download from Www.Somanuals.com. All Manuals Search And Download.
Also new to the JET ProShop 10" Table Saw is a heavy-
duty On/Off switch. We added a large paddle-style
lever that activates the OFF switch. The size and
location of the paddle makes it easy to turn the JET
ProShop 10" Table Saw off with your hand or a bump
of the leg.
Design Your Own!
The JET ProShop 10" Table Saw is available in several
versions designed to fit a wide range of shop size and
project needs. The JET ProShop 10" Table Saw can be
equipped with the 30” or 50” fence system, steel or
cast iron extension wings and with or without the
XACTA-Lift router plate in the extension wing.
Whatever your current or future shop needs, we have
a JET ProShop 10" Table Saw that will work for you
today and decades down the road.
The large paddle-style OFF switch
makes it easy to shut the
ProShop saw off by hand or with
a bump of your leg.
Download from Www.Somanuals.com. All Manuals Search And Download.
|