WARNING
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT USE THIS PLUG WITH AN EXTENSION CORD,
RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PRE-
VENT BLADE EXPOSURE. TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
audio
JCR-332
AM/FM Stereo CD Dual Alarm Clock Radio
INSTRUCTION MANUAL
The Caution Marking is located at the bottom enclosure of the apparatus.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Cleaning-Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol
cleaners. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product
may fall, causing serious injury to a child or adult, and serious damage to the product. Use
only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold
with the product. Any mounting of the product should follow the manufacturer’s instructions,
and should use a mounting accessory recommended by the manufacturer.A product and cart combination
should be moved with care-quick stops, excessive force and uneven surfaces may cause the product and
cart combination to overturn.
9. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that product heat.
10.Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide
blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
11. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and
the point where they exit from the apparatus.
12.Only use attachments/accessories specified by the manufacturer.
13.Unplug this apparatus during lightening storms or when unused for a long periods of time.
14.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been dam-
aged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or
has been dropped.
15.This appliance shall not be exposed to dripping or splashing water and that no object filled with liquids such
as vases shall be placed on the apparatus.
16.Do not overload wall outlet. Use only power source as indicated.
17.Use replacement part as specified by the manufacturer.
18.The product may be mounted to a wall only if recommended by the manufacturer.
19.Upon completion of any service or repairs to this product, ask the service technician to perform safety checks.
1
PLEASE READ THIS OPERATING MANUAL COMPLETELY
BEFORE OPERATING THIS UNIT AND RETAIN THIS
BOOKLET FOR FUTURE REFERENCE.
CRD- 732X IB J ENS 001 REV0 GB. p65
1
2008-5-6, 11:50
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER SUPPLY
LISTENING TO THE RADIO
1. Set the FUNCTION Selector (30) to the RADIO position.
2. Set the BAND Selector (26) to either AM or FM. If the FM band is selected, you are able
to choose either Mono or Stereo with the FM Mode Selector (28).
3. Press the ON / OFF Button (1) to turn on the radio and the POWER LED Indicator (14)
will turn on.
This CD clock radio operates on 120V ~ 60Hz household current. This unit also features a
9V DC battery back-up system for the clock settings (9V (006P) battery not included).
1. Insert the AC power cord (15) into a convenient standard AC wall outlet.
2. Follow the directions in the following section (Battery Back-up System) for steps on
installing the battery for the clock back-up.
4. Adjust the Volume (29) to the desired level.
5. Select your desired radio station using the TUNING Knob (27).
6. Reception: For FM, fully extend the antenna wire (32) and position the wire for best
reception. To receive a weak or noisy FM station, set the FM MODE Selector (28) to the
MONO position. The reception then may improve, but the sound is now monaural (MONO).
For AM, rotate the unit for best reception.
7. To turn the radio off, press the ON / OFF Button (1) and the POWER LED Indicator (14)
will go off.
BATTERY BACK-UP SYSTEM
The Battery Back-Up System ensures the clock and alarm settings will be retained during
AC power interruption.
NOTE: In order to preserve the battery life the display will not light during power disruption.
All clock settings will be kept in memory, however, the clock time may require adjustment
for exact accuracy. If no back-up battery is installed, the display will blink “
that you have to reset the time and alarm settings.
” to indicate
LISTENING TO THE CD PLAYER
BACKUP BATTERY INSTALLATION
1. Press the OPEN Button (3) to open the CD door. Insert your CD (label up) into the
compartment (4).
2. Switch the FUNCTION Selector (30) to the CD position.
3. Press the ON / OFF Button (1) once, the POWER LED Indicator (14) will turn on. The
Display (17) will briefly show the total number of tracks on the disc and return to the clock
time after few seconds.
4. To view which track is playing, press the DISPLAY Button (13) once. The Display will
briefly show the track no. of the current track and then return to clock time.
(5) to start playback from the first track. The Display (17) will show ‘ ’ then
return to the clock time.
Button is also used to pause playing of a track. Press once to pause, press
once again to continue to play.
1. Open the Battery Compartment Door and following the polarity diagram shown in the
Battery Compartment, connect one 9V DC battery (not included) onto the battery clip
inside the compartment. The battery only fits one way onto the connector, so ensure the
correct polarity prior to attaching.
2. Replace the Battery Compartment Door.
IMPORTANT: Be sure that the battery is installed correctly. Wrong polarity may damage
the unit.
3. For best performance and longer operating time, we recommend the use of an alkaline-
type battery.
4. If the unit is not to be used for an extended period of time, remove the battery. Old or
leaking battery can cause damage to the unit and will also void the warranty.
5. Do not dispose of battery in fire. Battery may leak or explode.
NOTE: An alkaline type battery is highly recommended for optimum performance and should
be replaced every 6 months for maximum back-up protection in the case of a power failure.
5. Press
NOTE : The
6. Rotate the Volume (29) to adjust to desired level.
7. Press STOP / CLOCK (6) to stop playback of the disc.
Important : After you finish using the CD player, make sure you turn off the power by
pressing the ON / OFF Button (1). The POWER LED Indicator (14) will go off.
NOTE : CD-Rs or CD-RWs playback capability in this player may vary depending on quality
of media, CD-Burner, speed of burning and application software.
SETTING THE TIME
This clock displays the time in two formats, 12 hour (12H) or 24 hour (24H) and by default is
set to 12H format.
1. Connect the AC plug into the convenient standard AC outlet, the LED Display blinks.
OTHER CD PLAYER FUNCTIONS
2. Press MIN
or HOUR
Buttons (11) to adjust the hours and minutes respectively.
3. Press STOP / CLOCK Button (6) again to set the clock time and the LED Display will
stop blinking.
SKIP / FAST SEARCH (
/
) (11): Press
to skip forward to the next track or
repeatedly to skip tracks. Press
to return to the beginning of the track, or press repeat-
NOTE
edly to skip backward several tracks. Press and hold
track.
or
to search quickly within a
There is a PM Indicator located in the top left-hand corner of the clock display. Be sure
to observe the PM Indicator when setting the time to make sure the time is set correctly for
AM or PM. If the PM Indicator is ‘On’, the time displayed is “PM”. If the PM Indicator is ‘Off’,
the time displayed is “AM”.
4. Press and hold the STOP / CLOCK Button (6) for 2 seconds to change the clock format
to “24H” if preferred. The LED Display will show “24H” for one second, then the clock
time will be shown in 24 hour format.
PLAY MODE(7):
- Press once to go into repeat one mode, your selected track will play
repeatedly. REPEAT Indicator (24) blinks.
- Press twice to go into repeat all mode, the disc plays continuously. The
REPEAT Indicator (24) lights.
- Press three times to go into random play mode, press
random play. The disc will play randomly. The REPEAT Indicator (24) will
go off and the RANDOM Indicator (23) will light.
- Press again to switch off this function, RANDOM Indicator (23) goes off.
once to start
4
5
CRD- 732X IB J ENS 001 REV0 GB. p65
3
2008-5-6, 11:50
Download from Www.Somanuals.com. All Manuals Search And Download.
PROGRAM (8):To set your own musical program.
1. Insert the disc. The total number of tracks is displayed in the LED Display
WAKE TO ALARM BUZZER
1. Set the FUNCTION Selector (30) to the Buzzer position.
(17).
2. The Alarm Indicator (21/ 22) will blink and the buzzer will sound when the alarm time is
reached. The buzzer will play for about one hour and then shut off automatically.
3. To stop the radio, press the ON/OFF Button (1). The Buzzer will stop but the alarm
remains set and will turn the unit on again at the same time on the following day.
4. If you do not want the alarm to turn the unit on the following day, press the AL1 or AL2
buttons once. The AL1 or AL2 Indicator (21/22) will go off.
2. Press Button (8) once, the display shows ‘
’ for 2 seconds, and then
“
” blinks along with the PROGRAM Indicator (25). Make sure your
player is in STOP mode.
3. Select your desired track with
or
(11), then press button (8) to store
your program in memory. Repeat this operation as many times as
necessary. Up to 20 tracks can be stored in the memory.
WAKE TO RADIO
4. Press
5. Press
(5) to start playing.
(6) to stop the disc.
1. Follow procedures 1 to 7 in “LISTENING TO THE RADIO” to set your radio wake up mode.
2. The alarm indicator (21 / 22) will blink and the Radio will turn on when the alarm time is
reached. The Radio will play for about one hour and then shut off automatically.
3. To stop the Radio, press the ON/OFF Button (1) once. The Radio will stop, but the alarm
remains set and will turn the unit on again at the same time on the following day.
4. If you do not want the alarm to turn the unit on the following day, press the AL1 or AL2
buttons once. The AL1 or AL2 Indicator (21/22) will go off.
6. To cancel this function, open the CD door.
LISTENNING TO THE EXTERNAL DEVICE (AUX)
THIS UNIT FEATURES AN AUX LINE-IN JACK FOR CONNECTING YOUR i-Pod, MP3
PLAYER OR OTHER DIGITAL MUSIC PLAYER.
1. Connect the headphone jack of your external device to the AUX LINE-IN jack (16) located
on the back of the JCR-332 (cable not included).
2. Turn on the JCR-332 and it will enter the AUX function mode once an external device is
plugged into the AUX LINE-IN jack.
3. Start playing your i-Pod, MP3 player or other external audio device.
4. Slowly adjust both volume controls on the JCR-332 and the external device.
5. Turn off your i-Pod, MP3 player etc. when finish listening. Turn the JCR-332 off and
unplug the AUX LINE-IN jack.
Remark: Once an AUX LINE-IN jack is plugged during POWER ON mode, it will automati-
cally enter the AUX mode no matter what position the FUNCTION Selector (30) is in. Re-
member to disconnect the cable from the JCR-332 after use in order to be able to listen to
the radio or CD player again.
WAKE TO CD
1. Follow the procedure 1 to 6 in “LISTENING TO THE CD PLAYER”
2. Press the ON / OFF Button (1) to turn off the unit. The POWER Indicator (14) goes off.
3. The Alarm Indicator (21/ 22) will blink and the CD will play when the alarm time is reached.
Note: The “REPEAT ALL” function will be active automatically when in Wake To CD mode,
and it will play for 60 minutes continuously unless the alarm is stopped.
The unit will automatically change to buzzer alarm if a damaged CD or the CD is incorrectly
inserted.
Remark: If an external device is plugged into AUX LINE-IN jack during ALARM ON mode,
it will change to Buzzer mode automatically no matter what position the FUNCTION Selec-
tor (30) is in.
If you want to be woken by a CD or Radio, make sure that the AUX LINE-IN jack is not
plugged.
OPERATING THE ALARM AND WAKE UP MODE
The JCR-332 allows you to set two different wake up times which you can choose to use
independently, as ALARM 1 or as ALARM 2 or simultaneously together.
1st Alarm (AL 1)
1. Press the AL 1 Button (9) once, the display blinks for a few seconds and the AL 1
Indicator (21) will light up.
2. When the Display blinks, press MIN and HOUR Button (11) to adjust the alarm time.
3. Press the AL 1 Button (9) again to memorize the alarm time. The Display (17) will resume
to clock time.
STOPPING THE ALARM
The alarm is programmed to run for 60 minutes.
1. Press the SNOOZE Button (2) to stop the alarm temporarily. The alarm will stop and
sound again automatically after 6 minutes.
2. Press the ON / OFF Button (1) once, the alarm will stop, and will sound again 24 hours
later.
3. To turn the alarm off permanently, press the AL1 / AL2 Button (9 / 10) repeatedly until the
Alarm LED Indicators (21 / 22) go off.
2nd Alarm (AL 2)
SLEEP TO MUSIC
1. Press the AL 2 Button (10) once, the display will blink for a few seconds and the AL 2
Indicator (22) will light up.
1. Select CD or Radio mode for sleep by setting the FUNCTION Selector (30) to the CD or
RADIO position.
2. When the Display blinks, press MIN and HOUR Button (11) to adjust the alarm time.
3. Press the AL 2 Button (10) again to memorize the alarm time. The Display (17) will
resume to clock time.
2. Press the SLEEP Button (12). The display shows “
” and the unit will go to the sleep mode.
3. Press the SLEEP Button (12) repeatedly to select the desired sleep time among 90, 60,
30 or 15 minutes.
NOTE
There is a PM INDICATOR located in the top left-hand corner of the clock display. Be sure
to observe the PM Indicator when setting the alarm to make sure the alarm time is set
correctly for AM or PM. If the PM Indicator is ‘On’, the alarm time will be “PM”. If the PM
Indicator is ‘off’, the alarm time will be “AM”.
4. The radio will automatically turn off when the sleep time has elapsed.
5. If “Sleep To CD” is selected, press the PLAY/PAUSE
playback will stop after the selected time is reached.
Button (5) to start playing and
6. If you want to turn off the unit before the preset sleep time has elapsed simply press the
ON / OFF Button (1).
6
7
CRD- 732X IB J ENS 001 REV0 GB. p65
4
2008-5-6, 11:50
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE : If the playing time of the CD is shorter than your selected sleep time, the music will
stop at the end of the disc.
TROUBLE SHOOTING GUIDE
If you experience difficulties in the use of this music system,please check the followings or
call 1- 800 - 777 - 5331 for Customer Service.
MORE INFORMATION
- Do not use your set immediately after moving from a cold place to a warm place.
Condensation may build up and cause functional problems in the unit.
- Make sure that you keep your set away from water and high temperatures.
- Clean the player with a soft damp (never wet) cloth. Never use solvents.
Symptom
Possible Cause
Solution
Noise or sound
distorted on AM or FM
broadcast.
Station not tuned properly forAM
or FM.
FM: Wire antenna is not
extended.
AM: The bar antenna is not
positioned correctly.
Retune the AM or FM broadcast
station.
Extend the FM wire antenna.
Reposition the unit until the best
reception is obtained.
NOTES ON COMPACT DISCS
- If there is a scratch, dirt or fingerprints on the CD, it may cause skipping or tracking errors.
Before playing, clean the CD with a cleaning cloth. Wipe the CD from the center out. Don’t
store discs in places with high temperatures or high humidity. They can become warped.
After playing, store the CD in its case.
FM STEREO Indicator
does not light.
Select another FM station.
Select FM STEREO mode.
You have tuned to a mono
station or the station is too weak.
MONO mode is chosen.
TECHNICAL SPECIFICATIONS
POWER SUPPLY : AC 120V ~ 60 Hz
Battery back-up - 9V 006P SIZE (not included)
FM / Frequency Modulation - 88 / 108 MHz
AM / Amplitude Modulation - 535 / 1705 kHz
Slide the Function selector to AM
or FM position.
Increase Volume.
Unit not set to AM or FM band.
Volume at minimum.
RADIO :
AM or FM no sound.
Select CD function mode.
Insert CD with label side up.
Use better quality blank media and
retest.
Unit not in CD function mode.
CARE AND MAINTENANCE
CD player will not play. CD is installed incorrectly.
If the CD is self-compiled, the
media used may not be
1. Clean your unit with a damp (never wet) cloth. Solvent or detergent should never be used.
2. Avoid leaving your unit in direct sunlight or in hot, humid or dusty places.
3. Keep your unit away from heating appliances and sources of electrical noise such as
fluorescent lamps or motors.
4. If drop-outs or interruptions occur in the music during CD play, or if
the CD fails to play at all, its bottom surface may require cleaning.
Before playing, wipe the disc from the center outwards with a good
soft cleaning cloth.
compatible with the player.
CD skips while playing.
Wipe CD with clean cloth or use
another disc.
Disc is dirty or scratched.
CD Intermittent sound. Dirty or defective disc.
Dirty Pick Up lens.
Clean or replace the defective disc.
Use a CD-lens cleaning disc to
clean the lens.
Relocate the player away from
shock or vibration.
Player is subject to excessive
shock or vibration.
5. Always clean the outside of the cabinet thoroughly if it becomes wet with moisture or
water splashes. This will help to prevent the internal parts of the unit from entry of water
and possible moisture damage.
SERVICE
COMPLIANCE WITH FCC REGULATIONS
Please refer to the instructions on the enclosed warranty card for returning your unit for
service. When returning the unit, please remove batteries to prevent damage to the unit in
transit and/or from possible battery leakage. We are not responsible for batteries returned
with the product or for the cost of replacement.
This equipment has been tested and found to comply with the limits for a Class B Digital
Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reason-
able protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Distributed by:
Spectra Merchandising International, Inc.
Chicago Industry Tech Park
4230 North Normandy Avenue
Chicago, IL 60634, U.S.A.
Please have model number ready, for Customer Service, call 1-800-777-5331
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio technician for help.
Printed in China
WARNING:
Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
8
9
CRD- 732X IB J ENS 001 REV0 GB. p65
5
2008-5-6, 11:50
Download from Www.Somanuals.com. All Manuals Search And Download.
|