Countertop
Lavatories
Instruction Guide
Caution:
Read all instructions carefully before starting
the installation.
Save this manual for future reference.
EASY-TO-FOLLOW GUIDE FOR OLD LAVATORY
REMOVAL, HOME INSTALLATION, AND MAINTENANCE.
HOW THIS GUIDE WILL HELP YOU
This guide describes everything you need to know about installing your new lavatory. It
includes drawings and descriptions of its parts. Before you begin examine all parts and the
drawings in this guide. If you read the instructions first, you will know what tools and
materials you should have ready during installation.
Please handle all parts carefully to prevent scratches and breakage.
Download from Www.Somanuals.com. All Manuals Search And Download.
SABER SAW
13. Place the four screw clips around the
lavatory so that the clips lock onto the metal
mountingframeasshowninFigure5. Tighten
the screws on the clips evenly all around.
Check the edges for additional sealant and
remove it immediately with a damp cloth.
5. A template has been provided with your
lavatory. This will help you cut an accurate
opening.Placethetemplateonthecountertop.
Normally you will want your lavatory to be
centeredbetweenthefrontedgeofthecounter
and the backsplash. If your counter is more
than 24" front to back, you may place the
lavatory 2" to 3" from the front counter edge.
The minimum distance from the lavatory to
the front of the counter should be 1-1/2". Be
sure to take the lavatory rim into account
when making your measurements.
HOLE FOR
STARTING CUTOUT
METAL MOUNTING FRAME
COUNTERTOP
Figure 3
9. It is best to mount the pop-up drain and
faucet before installing your lavatory. Be sure
to place the lavatory on a thick bed of news-
paperswhileworkingonittopreventscratches.
6. If your template is paper, fold it in half to
create a centerline. If your template is card-
board, measure the length and width of the
template to locate the center and draw a line.
Move the template to the desired position and
mark the location of the centerline. Measure
thedistancefromthecenterlinetothenearest
side wall or the end of the counter. Then
measurethesamedistancefromthesidewall
to locate the centerline at the back of the
lavatorytemplate. Nowtracetheoutlineofthe
Figure 5
SEALANT
Put in the pop-up drain first. Clean around the
drain hole with a damp cloth to remove any
dust or other particles that may interfere with
a good seal. Remove the washers, nuts, and
flange from the top of the pop-up. Coat the
underside of the flange with sealant (included
with your lavatory) and push it firmly into the
drain opening. Following the manufacturer's
instructions,tightentheflangefirmlyintoplace.
SCREW CLIP
14. Connectthedraintailpiecetothebottom
of the pop-up, then fasten the trap and drain
extension to the wall stub-out in the wall. See
Figure 6. You may use metal or plastic drain
pipe and trap, following the directions pro-
vided by the manufacturer.
The excess sealant that oozes out around the
flangeshouldbecleanedoffimmediatelywith
a damp cloth.
OVERFLOW
Figure 2
FLANGE
CONTROL
Next, attach the faucet according to the
manufacturer's instructions. Most of the fau-
cet installation is normally done with the lava-
toryupsidedown.Whenthefaucetissecurely
in place, attach the new hot and cold water
supply tubes to the faucet lines.
WASHER
DRAIN
CLEVIS
WASHER
SLIP NUT
PIVOT ROD
T DRAIN
DRAINPIPE
DRAIN TAILPIECE
SLIP NUT
RUBBER OR PLASTIC
WASHER
SLIP NUT
Figure 6
10. Put the metal mounting frame around
the lavatory. Bend the tabs in the frame to-
ward the lavatory, so that the frame is held to
the edges all the way around. See Figure 4.
11. Cleanthecountertopsurfacearoundthe
P TRAP
template accurately onto the countertop.
7. Measure across the metal mounting
frame from side to side to locate its center.
Mark this on the front of the frame. Move the
frame to the desired position and mark the
location of the centerline on the countertop.
Measure the distance from the centerline to
thenearestsidewallortheendofthecounter.
Then measure the same distance from the
side wall to locate the centerline at the back of
the counter.
15. Use a tube cutter to trim the free ends of
the hot and cold supply tubes to at least 1/4"
longer than necessary to reach into the inlets
of the shut-off valves. It is better to cut the
tubes longer than needed, then trim them
again. Remove any burrs or sharp edges with
an emery cloth.
BENT TAB
LAVATORY
TOP
Join the hot and cold water supplies to the
shut-off valves as instructed by the faucet
manufacturer.
Line up the frame with the centerline and
move it forward or back to its final location.
Placeapencilagainsttheoutsideoftheframe
as shown in Figure 2. Trace the outline of the
frame accurately onto the countertop. The
metal frame may have sharp edges. Handle it
carefully.
METAL MOUNTING
FRAME
16. Turnonthemainwatersupplythenopen
the shut-off valves. Check all connections for
leaks. A slight tightening of about 1/4 turn will
normally stop any leaks.
Figure 4
hole with a damp cloth. Apply a continuous
bead of sealant (included with your lavatory)
to the surface around the hole.
8. Drill a hole in the line you have drawn.
The hole should be large enough to take the
blade of a key hole or saber saw. Carefully
saw along the line. See Figure 3. Support the
piece you are cutting out to prevent splitting
when the cut is nearly complete.
12. Carefullyplacethelavatoryintothehole.
A helper may be necessary to lift it into posi-
tion. Align the lavatory in the hole, then push
downward at intervals all around the edge.
This will cause some of the sealant to ooze
out. Wipe off the excess immediately with a
damp cloth. It will be difficult to remove if
allowed to dry.
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE & CLEANING TIPS
Enameled Cast Iron
Forgeneralcleaning, useamild, nonabrasive
soap and warm water. Do not use abrasive
cleaners.Suchcleanerscontainsandorsilica
and will eventually scratch the enamel finish.
Stains, surface specks, and pot marks should
be removed without scrubbing by applying a
paste of such cleaners as BARKEEPERS
FRIEND or ZUD.
Surface roughness or "gritty feel" in a new
cast iron product can be eliminated by lightly
rubbing with a dry #600 sandpaper.
Rev. 11/98
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
JACUZZI WHIRLPOOL BATH (“Jacuzzi Whirlpool Bath”, “we”, “us”, “our”), warrants to the original consumer/
purchaser for the applicable warranty period set forth below, that the products we sell are free from defects in
material and workmanship, except as otherwise indicated below.
PRODUCTS
WARRANTY PERIOD
(commences upon date originally installed for its intended purpose)
•
All cast iron sink products with porcelain enamel
finish.
Limited lifetime vessel warranty to the original con-
sumer/purchaser only. The porcelain enamel finish is
warranted for one (1) year.
•
•
1.6 gpf/6 ltr. china toilets.
Five (5) years.
Two (2) years.
One (1) year.
Allotherchinaproductsandkitchensinkaccessories.
•
All toilet seats.
ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON
THESE PRODUCTS IS LIMITED IN DURATION TO THE WARRANTY PERIOD SPECIFIED ABOVE. SOME
STATESDONOTALLOWLIMITATIONSONHOWLONGANIMPLIEDWARRANTYLASTS, SOTHEABOVE
LIMITATIONS MAY NOT APPLY TO YOU.
This limited warranty does not cover:
(a) damage to any products based on or resulting from improper installation or repair, misuse or abuse
(including but not limited to excessive operating conditions), or alteration or adjustment other than in
conformity with our specifications or instructions, whether performed by a contractor, service company
or yourself;
(b) damages resulting from failure to reasonably clean, care for or maintain a product in accordance with
our instructions/recommendations; or,
(c) any products we sell that have been moved or removed from their original installation site.
If you believe that a product fails to meet the above limited warranty, you should notify us in writing prior to
expiration of the applicable warranty period set forth above at the following address: Jacuzzi Whirlpool Bath,
PO Box 702168, Dallas, TX 75370-2168. Notification should include a description of the product, model number
and how the product fails to meet the above warranty. Upon receipt of a written claim under this limited warranty
and evidence of the date of purchase or installation, and after inspection by an authorized Jacuzzi Whirlpool Bath
representative, at our option and in our sole discretion, we will either repair or replace the product with a Jacuzzi
WhirlpoolBathproductofthesameorsimilartypeandsize;provided,however,thatwewillnotpayanycosts(labor
or otherwise) associated with either removing a previously installed product; installing a replacement product; or
transportation or return of a product.
JACUZZI WHIRLPOOL BATH WILL NOT BE LIABLE FOR ANY OTHER LOSS OR EXPENSE(S) NOT
SPECIFICALLY DESCRIBED ABOVE, AND DISCLAIMS ANY LIABILITY FOR CONSEQUENTIAL OR
INCIDENTAL DAMAGES.
SOMESTATESDONOTALLOWTHEEXCLUSIONORLIMITATIONOFINCIDENTALORCONSEQUENTIAL
DAMAGES, SO THE ABOVE EXCLUSION MAY NOT APPLY TO YOU.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS
WHICH VARY FROM STATE TO STATE.
Download from Www.Somanuals.com. All Manuals Search And Download.
|