HT994SJ-AHP_BCANLLK_Eng
DVD DIGITAL THEATER SYSTEM
TH-G41
Consists of XV-THG41, SP-THG51F,
SP-THG61C and SP-THG50W
TUNING
TUNING
iPod is a trademark of Apple Inc., registered in the U.S. and other countries.
iPhone is a trademark of Apple Inc.
INSTRUCTIONS
LVT2052-002A
[C]
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS IN THIS OWNER’S MANUAL. AND
THOSE MARKED ON THE PRODUCT. RETAIN THIS BOOKLET FOR FUTURE REFERENCE.
CAUTION:
This product has been designed and manufactured to assure personal safety. Improper use can result in electric shock or
fire hazard. The safeguards incorporated in this product will protect you if you observe the following procedures for
installation, use, and servicing.
This product does not contain any parts that can be repaired by the user.
DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.
1. Read these instructions. - All these safety and
operating instructions should be read before the product
is operated.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.
2. Keep these instructions. - The safety, operating and
use instructions should be retained for future reference.
11. Only use attachments/accessories specified by the
manufacturer.
3. Heed all warnings. - All warnings on the product and in
the operating instructions should be adhered to.
12. Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
apparatus. When a cart is used, use caution when
moving the cart/product combination to avoid
injury from tip-over.
4. Follow all instructions. - All operating and use
instructions should be followed.
5. Do not use this apparatus near water. - For example:
near a bath tub, wash bowl, kitchen sink, laundry tub, in
a wet basement; or near a swimming pool; and other
areas located near water.
6. Clean only with dry cloth. - Unplug this product from
the wall outlet before cleaning. Do not use liquid
cleaners.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions. - Slots
and openings in the cabinet are provided for ventilation
and to ensure reliable operation of the product and to
protect it from over- heating. The openings should never
be blocked by placing the product on a bed, sofa, rug or
other similar surface. This product should not be placed
in a built-in installation such as a bookcase or rack
unless proper ventilation is provided or the
13. Unplug this apparatus during lightning storms or
when unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the product has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the product has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
manufacturer’s instructions have been adhered to.
8. Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety.
If the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete
outlet.
G-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Introduction . . . . . . . . . . . . . . . . . . .2-5
LOCK (PARENTAL CONTROL) . . . . . . . . . .13
• Initial Setting the Area Code . . . . . . . . .13
• Rating . . . . . . . . . . . . . . . . . . . . . . . . . .13
• Password . . . . . . . . . . . . . . . . . . . . . . . .13
• Area Code . . . . . . . . . . . . . . . . . . . . . . .13
OTHERS . . . . . . . . . . . . . . . . . . . . . . . . . . .13
About the ꢀ Symbol Display . . . . . . . . . . . . . .2
Symbol Used in this Manual . . . . . . . . . . . . . . .2
Screen Saver . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Notes on Discs . . . . . . . . . . . . . . . . . . . . . . . . . .2
Handling Discs . . . . . . . . . . . . . . . . . . . . . . . .2
Storing Discs . . . . . . . . . . . . . . . . . . . . . . . . .2
Cleaning Discs . . . . . . . . . . . . . . . . . . . . . . . .2
Types of Playable Discs . . . . . . . . . . . . . . . . . .3
Regional Code . . . . . . . . . . . . . . . . . . . . . . . . . .3
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . .5
Remote Control operation . . . . . . . . . . . . . . .5
Remote Control Battery installation . . . . . . . .5
Operations . . . . . . . . . . . . . . . . .14-21
General Features . . . . . . . . . . . . . . . . . . . . . . .14
Additional Features . . . . . . . . . . . . . . . . . . . . .15
Playing an Audio CD or MP3/WMA file . . . . .16
Programmed Playback . . . . . . . . . . . . . . . . . .17
Repeat Programmed Tracks . . . . . . . . . . . .17
Erasing a Track from Program List . . . . . . .17
Erasing the Complete Program List . . . . . . .17
Viewing a JPEG file . . . . . . . . . . . . . . . . . . . . .18
Slide Show . . . . . . . . . . . . . . . . . . . . . . . . . .18
Still Picture . . . . . . . . . . . . . . . . . . . . . . . . . .18
Moving to another file . . . . . . . . . . . . . . . . . .18
Rotating the picture . . . . . . . . . . . . . . . . . . .18
Listening to music during slide show . . . . . .18
Using iPod . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
General operation . . . . . . . . . . . . . . . . . . . .19
General features . . . . . . . . . . . . . . . . . . . . .19
Presetting the Radio Stations . . . . . . . . . . . . .20
To tune in a station with a weak signal . . . .20
To clear all the stored stations . . . . . . . . . .20
Listening to the Radio . . . . . . . . . . . . . . . . . . .20
To turn off the radio . . . . . . . . . . . . . . . . . . .20
To listen to non-preset radio stations . . . . .20
To select a preset radio station directly . . . .20
Sleep Timer Setting . . . . . . . . . . . . . . . . . . . . .21
Dimmer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Muting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Setting the disc ejection lock . . . . . . . . . . . . .21
Enjoying audio form an external source . . . .21
Setting the surround mode . . . . . . . . . . . . . . .21
Installation and Setup . . . . . . . . .6-13
TV Connection . . . . . . . . . . . . . . . . . . . . . . . . . .6
Video connection . . . . . . . . . . . . . . . . . . . . . .6
Component Video connection . . . . . . . . . . . .6
Antenna Connection . . . . . . . . . . . . . . . . . . . . .6
Optional Equipment Connection . . . . . . . . . . .7
AUX IN connection (A) . . . . . . . . . . . . . . . . . .7
OPTICAL IN connection (O) . . . . . . . . . . . . . .7
AUDIO IN connection (D) . . . . . . . . . . . . . . . .7
HDMI In connection (H) . . . . . . . . . . . . . . . . .7
iPod connection (I) . . . . . . . . . . . . . . . . . . . . .7
HDMI Connection . . . . . . . . . . . . . . . . . . . . . . . .8
About HDMI . . . . . . . . . . . . . . . . . . . . . . . . . .8
Resolution setting . . . . . . . . . . . . . . . . . . . . . .8
Available resolution according to connection .8
Speaker System Connection . . . . . . . . . . . . . .9
Displaying Disc Information on-screen . . . . .10
Initial Settings . . . . . . . . . . . . . . . . . . . . . . .10-13
OSD Initial language settings . . . . . . . . . .10
General Operation . . . . . . . . . . . . . . . . . .11
Language . . . . . . . . . . . . . . . . . . . . . . . . .11
• Menu language . . . . . . . . . . . . . . . . . . .11
• Disc Audio / Subtitle / Menu . . . . . . . . .11
DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
• TV Aspect . . . . . . . . . . . . . . . . . . . . . . .11
• Display Mode . . . . . . . . . . . . . . . . . . . . .11
AUDIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
• Dynamic Range Control (DRC) . . . . . . .12
• Vocal . . . . . . . . . . . . . . . . . . . . . . . . . . .12
• HD AV Sync . . . . . . . . . . . . . . . . . . . . .12
5.1 SPEAKER SETUP . . . . . . . . . . . . . .12-13
Reference . . . . . . . . . . . . . . . . . . .22-25
Language Codes . . . . . . . . . . . . . . . . . . . . . . . .22
Area Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Troubleshooting . . . . . . . . . . . . . . . . . . . . . .23-24
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . .25
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
To ensure proper use of this product, please read this
owner’s manual carefully and retain it for future
reference.
Notes on Discs
Handling Discs
This manual provides information on the operation
and maintenance of your DVD player. Should the unit
require service, contact an authorized service location.
Do not touch the playback side of the disc. Hold the
disc by the edges so that fingerprints do not get on
the surface. Never stick paper or tape on the disc.
ꢀ
About the
Symbol Display
“ ꢀ ” may appear on your TV display during operation
and indicates that the function explained in this
owner’s manual is not available on that specific DVD
video disc.
Storing Discs
After playing, store the disc in its case. Do not expose
the disc to direct sunlight or sources of heat and never
leave it in a parked car exposed to direct sunlight.
Symbol Used in this Manual
Note:
Indicates special notes and operating features.
Cleaning Discs
Fingerprints and dust on the disc can cause poor
picture quality and sound distortion. Before playing,
clean the disc with a clean cloth. Wipe the disc from
the center out.
Tip:
Indicates tips and hints for making the task easier.
A section whose title has one of the following symbols is
applicable only to the disc represented by the symbol.
ALL
All discs and file listed below
DVD
DVD and finalized DVD R/RW
ACD
Audio CDs
MP3
MP3 files
WMA
WMA files
Do not use strong solvents such as alcohol, benzine,
thinner, commercially available cleaners, or anti-static
spray intended for older vinyl records.
JPEG
JPEG files
Screen Saver
The screen saver activates when there is no
operation made for approximately 5 minutes since a
still picture was last displayed.
To cancel the screen saver, push any key.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Types of Playable Discs
Regional Code
DVD
This unit has a regional code printed on the rear of the
unit. This unit can play only DVD discs labelled as the
same as the rear of the unit or “ALL”.
(8 cm / 12 cm disc)
Audio CD
(8 cm / 12 cm disc)
Notes on Regional Codes
• Most DVD discs have a globe with one or more
numbers in it clearly visible on the cover. This
number must match your unit’s regional code or the
disc cannot play.
In addition, this unit plays DVD R/RW and CD-R/RW,
Dual disc that contains audio titles, MP3, WMA, and/or
JPEG files.
• If you try to play a DVD with a different regional
code from your player, the message “Check
Regional Code” appears on the TV screen.
Notes:
• Depending on the conditions of the recording
equipment or the CD-R/RW (or DVD R/RW) disc
itself, some CD-R/RW (or DVD R/RW) discs
may not be played on the unit.
Notes on Copyrights:
It is forbidden by law to copy, broadcast, show,
broadcast via cable, play in public, or rent copyrighted
material without permission. This product features the
copy protection function developed by Macrovision.
Copy protection signals are recorded on some discs.
When recording and playing the pictures of these
discs picture noise will appear. This product
incorporates copyright protection technology that is
protected by method claims of certain U.S. patents
and other intellectual property rights owned by
Macrovision Corporation and other rights owners.
The Use of this copyright protection technology must
be authorized by Macrovision Corporation, and is
intended for home and other limited viewing uses only
unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is
prohibited.
• Do not use irregularly shaped CDs (e.g., heart-
shaped or octagonal) since they may result in
malfunctions.
• This unit requires discs and recordings to meet
certain technical standards in order to achieve
optimal playback quality. Pre-recorded DVDs are
automatically set to these standards. There are
many different types of recordable disc formats
(including CD-R containing MP3 or WMA files) and
these require certain pre-existing conditions (see
above) to ensure compatible playback.
Customers should note that permission is
required in order to download MP3 / WMA files
and music from the Internet. Our company has
no right to grant such permission. Permission
should always be sought from the copyright
owner.
CONSUMERS SHOULD NOTE THAT NOT ALL HIGH
DEFINITION TELEVISION SETS ARE FULLY
COMPATIBLE WITH THIS PRODUCT AND MAY
CAUSE ARTIFACTS TO BE DISPLAYED IN THE
PICTURE. IN CASE OF 525 PROGRESSIVE SCAN
PICTURE PROBLEMS, IT IS RECOMMENDED THAT
THE USER SWITCH THE CONNECTION TO THE
‘STANDARD DEFINITION’ OUTPUT. IF THERE ARE
QUESTIONS REGARDING OUR TV SET
COMPATIBILITY WITH THIS MODEL 525p DVD
PLAYER, PLEASE CONTACT OUR CUSTOMER
SERVICE CENTER.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Front Panel
a
b
c
d e f g h i
j
a 1/' (STANDBY/ON)
g X (PAUSE)
Pause playback.
FM MODE
Switches the unit ON and OFF.
b Disc Tray
This will change the tuner from stereo to mono
and usually improve the reception.
Insert a disc here.
c AUDIO IN
h . (SKIP)
The AUDIO IN port means you can connect a
audio device to play through the surround sound
speakers.
Returns to the beginning of current chapter or
track or go to the previous chapter or track.
(SCAN)
During playback, press and hold this button
repeatedly to select the required scan speed.
- TUNING
d Z (OPEN/CLOSE)
Opens or closes the disc tray.
e x (STOP)
Tunes in the desired radio station.
Stops playback.
i > (SKIP)
f B (PLAY)
Go to the next chapter or track.
(SCAN)
During playback, press and hold this button
repeatedly to select the required scan speed.
+ TUNING
Starts playback.
SOURCE
Press and hold down this button about 3 seconds,
then press repeatedly to select other function
Tunes in the desired radio station.
j VOLUME controller
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control
0-9 numerical buttons: Selects
numbered options in a menu.
AUDIO (1/')
Switches the unit ON and OFF.
FUNCTION
SURROUND
Selects the surround mode.
Selects the function (DVD/CD, FM)
INPUT
SCAN MODE
Sets the output resolution for HDMI
and COMPONENT VIDEO OUT
jacks.
Changes the input source ( AUX,
AUX OPT, AUDIO IN, OSD IPOD,
IPOD, HDMI IN)
SLEEP
Sets the System to turn off
SUBTITLE
Selects a subtitle language (DVD).
automatically at a specified time.
PROG./MEMO.
DIMMER
Changes brightness of the display
window on the front panel during in
power-on status.
Accesses or removes Program
menu.
Enter a radio station’s frequency into
the tuner.
RETURN
Press to move back wards in the
menu.
REPEAT
Repeats chapter, track, title, all
CLEAR
TUNING
TUNING
TOP MENU
If the current DVD title has a menu,
the title menu appears on the
screen. Otherwise, the disc menu
may appear.
Removes a track number on the
Program List.
SCAN/SLOW(bb/BB)
Searches backward or forward.
Reverse/ Forward slow playback.
MENU
SKIP (./>)
STOP (x)
Accesses the menu on a DVD disc.
SET UP
Accesses or removes setup menu.
PLAY (B)
DISPLAY
Accesses On-Screen display.
FM MODE
This will change the tuner from
stereo to mono and usually improve
the reception.
b/B/v/V (left/right/up/down)
Selects an option in the menu.
ENTER
PAUSE (X)
Acknowledges the menu selection.
VOLUME (-/+)
Adjusts speaker volume.
PRESET (#/3)
Selects program of Radio.
MUTING
TUNING. (#/3)
Tunes in the desired radio station.
To mute the sound
Remote Control operation
Point the remote control at the remote sensor and
press the buttons.
Remote Control Battery installation
Detach the battery cover on the rear
of the remote control, and insert two
batteries (size AAA) with 3 and #
aligned correctly.
Cautions:
• Do not mix old and new batteries and never mix
different types of batteries such as standard,
alkaline, etc.
• Do not put the batteries in the place where young
children can reach.
• Battery shall not be exposed to excessive heat
such as sunshine, fire or the like.
• When discarding batteries, environmental problems
must be considered and local rules or laws
governing the disposal of these batteries must be
followed strictly.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Setup
Video connection
TV Connection
Make one of the following connections, depending on
Connect the MONITOR OUT jack from the DVD/CD
Receiver to the VIDEO IN jack on the TV using the
video cable (V).
the capabilities of your existing equipment.
Component Video connection
Tips:
ꢀ Depending on your TV and other equipment you
wish to connect, there are various ways you could
connect the DVD/CD Receiver. Use one of the
connections described below.
Connect the COMPONENT VIDEO OUT jacks from
the DVD/CD Receiver to the corresponding jacks on
the TV using an Y PB PR cable (C).
ꢀ If your television is a high-definition or “digital
ready” television, you may take advantage of the
DVD/CD Receiver’s progressive scan output for the
highest video resolution.
ꢀ If your TV does not accept your resolution setting,
abnormal picture appears on the screen. Please
read owner’s manual for TV then set the resolution
that your TV can accept.
ꢀ Please refer to the manuals of your TV, VCR,
Stereo System or other devices as necessary to
make the best connections.
Caution:
ꢀ
Make sure the DVD/CD Receiver is connected
directly to the TV. Select the correct AV input on
your TV.
ꢀ Do not connect your DVD/CD Receiver to TV via
your VCR. The DVD image could be distorted by
the copy protection system.
Antenna Connection
Connect the supplied FM antenna for listening to the
radio.
Rear of TV
ꢀ Connect the FM Wire antenna to the FM antenna
connector.
VIDEO
INPUT
COMPONENT VIDEO /
PROGRESSIVE SCAN INPUT
FM Wire Antenna
(supplied)
C
V
(supplied)
(not supplied)
Notes:
ꢀ
ꢀ
Be sure to fully extend the FM wire antenna.
After connecting the FM Wire antenna, keep it as
horizontal as possible.
Rear of DVD/CD Receiver
6
Download from Www.Somanuals.com. All Manuals Search And Download.
iPod connection (I)
Optional Equipment Connection
Connect the iPod and the unit with iPod docking
station.(I).
Rear of DVD/CD Receiver
iPod
(not supplied)
A
(supplied)
I
(not
suppl
ied)
O
H
(not
OUT
IN
VIDEO
supplied)
AUDIO (L)
AUDIO (R)
OPTICAL
OUT
Rear of DVD/CD Receiver
Auxiliary device
DVD Player
(or Digital
Notes:
• The connector plug is protected with a cover when
it is first purchased. Please remove the cover
before operationg the unit.
• When the iPod is not connected, insert the terminal
cover. This prevents dust from entering and
possibly damaging the unit.
Device, etc)
AUX IN connection (A)
Connect a Output of auxiliary device to the AUX
AUDIO Input (L/R) Connector.
OPTICAL IN connection (O)
• Depending on the type of iPod, you may need to
insert one of the dock adapters into the dock slot
before you station your iPod.
• Adjust the volume to a moderate level before you
connect your iPod and this unit.
Connect an optical output of DVD Player (or Digital
Device etc) to the OPTICAL IN connector.
HDMI In connection (H)
Connect the HDMI INPUT jack on the unit to the
HDMI output jack on your DVD Player (or Digital
Device etc.) using an HDMI cable. Set the external
source to HDMI IN by pressing INPUT. In HDMI IN
mode, you can’t change the resolution. Change the
resolution on your DVD Player (or Digital Device etc.)
by connectiong the unit.
• The jack for the iPod cable of docking station are
keyed so that the cable connectors only connect in
one way. Connect the end on the cable with the
marked “v” facing down wards to rear on the unit.
Note:
Image of HDMI input can not output from component
and composite output.
AUDIO IN connection (D)
Connect a output of portable device (MP3 or PMP
etc) to the AUDIO input connector.
To AUDIO IN
D
(not supplied)
To AUDIO OUT
Portable device
7
Download from Www.Somanuals.com. All Manuals Search And Download.
HDMI Connection
About HDMI
HDMI compatible TV
HDMI
HDMI (High Definition Multimedia Interface) supports
both video and audio on a single digital connection for an
easy all- digital output to an HDMI or DI-equipped TV.
(not supplied)
H
Connection to an HDMI TV requires an HDMI cable
while connection to a DVI-equipped TV requires a DVI
adapter besides a HDMI cable.
HDMI has the capability to support standard,
enhanced, or high-definition video plus standard to
multi-channel surround-sound audio, HDMI features
include uncompressed digital video, a bandwidth of up
to 5 gigabytes per second, one connector (instead of
several cables and connector), and communication
between the AV source and AV devices such as DTVs.
Rear of DVD/CD Receiver
Resolution setting
You can change the resolution for component video
and HDMI output.
Press SCAN MODE repeatedly to select the desired
resolution - 480i, 480p, 720p, 1080i, 1080p
The resolution may not be selected depending on the
connection or TV.
HDMI, the HDMI logo and High-Definition Multimedia
Interface are trademarks or registered trademarks of
HDMI licensing LLC.
If you have a HDMI TV or monitor, you can connect
it to this DVD/CD Receiver using a HDMI cable.
Note:
Depending on your TV, some of the resolution settings
may result in the picture disappearing or an abnormal
picture appearing. In this case, press SCAN MODE
1. Connect the HDMI OUT jack on the DVD/CD
Receiver to the HDMI jack on a HDMI compatible
TV or monitor (H).
repeatedly until the picture re-appears.
You can set 1080p video resolution to enjoy Full HD picture
quality. (Full HD up-scaling)
2. Set the TV’s source to HDMI (refer to owner’s
manual for TV).
Available resolution according to connection
Notes on HDMI Out connection
• If your TV does not accept your resolution setting,
abnormal picture appears on the screen.(“TV do not
support” will appears in screen)
HDMI OUT - 1080p, 1080i, 720p 480p and 480i
COMPONENT VIDEO OUT - 480p and 480i
VIDEO OUT - 480i
Please read owner’s manual for TV, and then set
the resolution that your TV can accept.
• Changing the resolution when the unit is connected
with HDMI connector may result in malfunctions. To
solve the problem, turn off the unit and then turn it
on again.
Note:
If your TV does not accept your resolution setting,
abnormal picture appears on the screen.
Please read owner’s manual for TV, and then set the
resolution that your TV can accept.
• When you connect a HDMI or DVI compatible
device make sure of the following :
- Try switching off the HDMI/ DVI device and this
unit. Next, switch on the HDMI/ DVI device and
leave it for around 30 seconds, then switch on this
unit.
- The connected device’s video input is set correctly
for this unit.
- The connected device is compatible with
720X576i(480i), 720X576p(480p), 1280X720p,
1920X1080i or 1920X1080p video input.
- The 1080p, 720p and 576p(480p) resolutions are
the progressive scan applied resolution.
• Not all HDCP-compatible DVI devices will work with
this unit.
- The picture will not be displayed properly with non-
HDCP device.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Speaker System Connection
Connect the speakers using the supplied speaker
cables.
To obtain the best possible surround sound, adjust the
speaker parameters (volume, distance, etc.).
Center speaker
Front speaker
(Left)
Front speaker
(Right)
Notes:
• Be sure to match the speaker cable to the
appropriate terminal on the components: + to + and
– to –. If the cables are reversed, the sound will be
distorted and will lack base.
• If you use front speakers with low maximum input
rating, adjust the volume carefully to avoid
excessive output on the speakers.
Rear speaker
(Left surround)
Rear speaker
(Right surround)
Caution:
• The left and right speakers can be installed on a
wall.
Subwoofer
• When installing the speakers on a wall, be sure to
have the speakers installed by qualified personnel.
• DO NOT install the speakers on the wall by yourself
to avoid unexpected damage from them falling off
the wall due to incorrect installation or weakness in
wall structure.
• Care must be taken in selecting a location for
speaker installation on a wall. Injury to personnel or
damage to devices may result if the installed
speakers interfere with daily activities.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Displaying Disc Information
on-screen
You can display various information about the disc
loaded on-screen.
Initial Settings
By using the Setup menu, you can make various
adjustments to items such as picture and sound.
You can also set a language for the subtitles and the
Setup menu, among other things. For details on each
Setup menu item, see pages 10 to 13.
1. Press DISPLAY to show various playback
information.
OSD Initial language settings:
When the POWER is turned on for the first time, the
unit need to set the menu language. Follow the
descriptions below after the display connections. After
OSD Initial language setting, to set Area code (see
page 13)
The displayed items differ depending on the disc
type or playing status.
1. Press POWER to turn the unit on. The language
setup menu will appear on the screen.
2. Use b / B / v / V to select a language then press
ENTER. The confirm menu will appear.
3. Use b / B to select the [Enter] then press ENTER
to finish the language setup.
To display and exit the Menu:
Press SETUP to display the menu. A second press of
SETUP will take you back to initial screen.
To go to the next level:
2. You can select an item by pressing v / V and
change or select the setting by pressing b / B.
Press B on the remote control.
ꢀ Title – Current title number/ total number of
titles.
ꢀ Chapter – Current chapter number/total number
of chapters.
To go back to the previous level:
Press b on the remote control.
About help menu
ꢀ Time – Elapsed playing time.
ꢀ Audio – Selected audio language or channel.
ꢀ Subtitle – Selected subtitle.
ꢀ Angle – Selected angle/total number of angles.
ꢀ Sound – Selected sound mode.
Menu
Buttons
Operation
v / V Move
v / V
Moving to another
menu
b Prev.
b
B
Moving to previous
level
B Select
Moving to next level or
selecting menu
Note:
If any button is not pressed for a few seconds, the on-
screen display disappears.
RETURN 5.1 Speaker Setup
menu
ENTER
To confirm menu
10
Download from Www.Somanuals.com. All Manuals Search And Download.
DISPLAY
General Operation
1. Press SETUP.
The Setup menu appears.
TV Aspect
4:3 – Select when a standard 4:3 TV is connected.
16:9 – Select when a 16:9 wide TV is connected.
2. Use v / V to select the desired option then press
B to move to the second level. The screen shows
the current setting for the selected item, as well as
alternate setting(s).
Display Mode
The Display Mode setting works only when the TV
Aspect mode is set to 4:3.
3. Use v / V to select the second desired option and
then press B to move to the third level.
Letterbox – Displays a wide picture with bands on
the upper and lower portions of the screen.
4. Use v / V to select the desired setting then press
ENTER to confirm your selection.
Panscan – Automatically displays the wide picture
on the entire screen and cuts off the portions that
do not fit. (If the disc/file is not compatible with
Pan Scan, the picture is displayed at Letterbox
ratio.)
Some items require additional steps.
5. Press SETUP or PLAY (N) to exit the Setup
menu.
LANGUAGE
Menu Language
Select a language for the Setup menu and then on-
screen display.
Disc Audio / Subtitle / Menu
Select the language you prefer for the audio track
(disc audio), subtitles, and the disc menu.
Original – Refers to the original language in which
the disc was recorded.
Other – To select another language, press
numeric buttons and then ENTER to enter the
corresponding 4-digit number according to the
language code list on the page 22. If you enter the
wrong language code, press CLEAR.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
AUDIO
5.1 Speaker Setup
Make the following settings for the built-in 5.1 channel
surround decoder.
Each DVD disc has a variety of audio output options.
Set the player’s AUDIO options according to the type
of audio system you use.
1. Press ENTER, and the 5.1 Speaker Setup menu
appears.
Dynamic Range Control (DRC)
2. Use b / B to select the desired speaker.
3. Adjust options using v / V / b / B buttons.
With the DVD*1 format, you can hear a program’s
soundtrack in the most accurate and realistic
presentation, thanks to digital audio technology.
However, you may wish to compress the dynamic
range of the audio output (the difference between the
loudest sounds and the quietest ones). Then, you may
listen to a movie at a lower volume without losing
clarity of sound. Set DRC to On for this effect.
*1:Dolby Digital only
4. Press ENTER to confirm your selection. Returns to
the previous menu.
Speaker selection
Select a speaker that you want to adjust. [Front
speaker (Front L), Front speaker (Front R), Center
Speaker (Center), Subwoofer (SubWoofer), Rear
speaker (Rear L), Rear speaker (Rear R)]
Vocal
Note:
Set Vocal to On only when a multi-channel karaoke
DVD is playing. The karaoke channels on the disc will
mix into normal stereo sound.
Certain speaker settings are prohibited by the Dolby
Digital licensing agreement.
Size
HD AV Sync
Since the speaker settings are fixed, you cannot
change the settings.
When using Digital TV.
Sometimes AV signal could not be transmitted
simultaneously because of later transmission of video
signal compared to audio signal.
Because it takes some time to convert analogue video
signal to digital one in the Digital TV.
And It means that you may not enjoy picture on the
screen and sound from speaker at the same time
even though it is one scene.
Volume
Press b / B to adjust the output level of the selected
speaker. (-5dB ~ 5dB)
Distance
After you connected speakers to your DVD Receiver,
set the Distance between the speakers and your
listening point if the distance of Center or Rear
speakers is bigger than the distance of Front
speakers. This allows the sound from each speaker to
reach the listener at the same time.
Press b / B to adjust the Distance of the selected
speaker. This distance is equivalent to a difference of
the distance between Center or Rear speaker and
Front speakers.
In the HD AV Sync menu, you could adjust delay time
to audio signal for simultaneous AV signal
transmission
ꢀ Delay time could be set up with 10msec unit.
(0 ~ 300ms)
ꢀ Delay time is different according to each TV Brand.
So you need to adjust optimal delay time complying
with your TV.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Rating
5.1 Speaker Setup
Blocks playback of rated DVDs based on their
contents. Not all discs are rated.
1. Select “Rating” on the LOCK menu then press B.
2. Input a password and press ENTER.
3. Select a rating from 1 to 8 using the v / V buttons.
Rating 1-8: Rating one (1) has the most restrictions
and rating eight (8) is the least restrictive.
Unlock: If you select unlock, parental control is
not active and the disc plays in full.
Test
Press b / B to test the signals of each speaker. Adjust
the volume to match the volume of test signals
memorized in the system.
Front Left (Front L) → Center→ Front Right (Front R)
→ Rear Right (Rear R) → Rear Left (Rear L) →
SubWoofer
LOCK (Parental Control)
4. Press ENTER to confirm your rating selection, then
press SETUP to exit the menu.
Password
You can enter or change password.
1. Select Password on the LOCK menu and then
press B.
2. Follow the step 2 as shown above (Rating).
To change the password, press ENTER when the
“Change” option is highlighted. Input a password
and press ENTER. Enter it again and press
ENTER to verify.
3. Press SETUP to exit the menu.
Initial Setting the Area Code:
If you forget your password
See the Area Codes on page 22.
If you forget your password, you can clear it using the
following steps:
1. Press SETUP to display the Setup menu.
2. Select the LOCK menu.
3. Input the 6-digit number “210499” and press
ENTER. The password is cleared.
Area Code
Enter the code of the area whose standards were
used to rate the DVD video disc, based on the list on
page 22.
1. Select “Area Code” on the LOCK menu then
press B.
1. Select the LOCK menu and then press B.
2. Follow the step 2 as shown previous paragraph
(Rating).
3. Select the first character using v / V buttons.
4. Press ENTER and select the second character
using v / V buttons.
2. To access the LOCK options, you must input the
password you have created. Input a password and
press ENTER. Enter it again and press ENTER to
verify. If you make a mistake before pressing
ENTER, press CLEAR.
3. Select the first character using v / V buttons.
4. Press B and select the second character using
v / V buttons.
5. Press ENTER to confirm your Area code selection.
OTHERS
5. Press ENTER to confirm your Area code selection.
This option has no selection on this set.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
General features
Buttons
Operations
Discs
ALL
Z (OPEN / CLOSE)
X (PAUSE)
Opens or closes the disc tray.
During playback, press X to pause playback.
Press X repeatedly to play Frame-by-Frame.
ALL
DVD
. / >
m / M
During playback, press . or > to go to the next
chapter/track or to return to the beginning of the current
chapter/track.
ALL
Press . twice briefly to step back to the previous
chapter/track.
During playback, press m or M repeatedly to select the
required scan speed.
DVD : bb, bbb, bbbb, bbbbb or
BB, BBB, BBBB, BBBBB
DVD
ACD
MP3
WMA
WMA/MP3, Audio CD : m (X2, X4, X8) or M (X2, X4, X8)
REPEAT
During playback, press REPEAT repeatedly to select a
desired repeat mode.
ALL
DVD Video discs: Chapter/Title/Off
Audio CD, MP3/WMA discs: Track/All/Off
TOP MENU
If the current DVD title has a menu, the title menu appears
on the screen. Otherwise, the disc menu may appears.
DVD
MENU
The disc menu appears on the screen.
DVD
DVD
(SUBTITLE)
During playback, press SUBTITLE repeatedly to select a
desired subtitle language.
DVD
In the pause mode, press SLOW (m or M) to select the
required speed.
SLOW
DVD : t (1/2, 1/4, 1/8, 1/16) or T (1/2, 1/4, 1/8, 1/16)
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional features
Time Search DVD
To start playing at any chosen time on the disc:
1. Press DISPLAY during playback.
2. Press v / V to select the time clock icon and
“--:--:--” appears.
3. Input the required start time in hours, minutes, and
seconds from left to right. If you enter the wrong
numbers, press CLEAR to remove the numbers
you entered. Then input the correct numbers.
4. Press ENTER to confirm. Playback starts from the
selected time.
1.5 times speed playback
DVD
You can play at 1.5 times speed.
The 1.5 speed allows you to watch the pictures and
listen to the sound quicker than playing at a normal
speed on the disc.
1. During playback, press PLAY(B) to play at 1.5
times speed. “BX1.5” appears on the screen.
2. Press PLAY(B) again to exit.
Screen Saver
The screen saver appears when you leave the unit in
Stop mode for about five minutes. To cancel the
Screen Saver, press any button and then operate the
unit.
Last Scene Memory DVD
This receiver memorizes the last scene from the last
disc that is viewed. The last scene remains in the
memory even if you remove the disc from the receiver
or switch off the receiver. If you load a disc that has
the scene memorized, the scene is automatically
recalled.
Note:
This receiver does not memorize the scene of a disc if you
switch off the receiver before commencing to play the disc.
Mixed disc – MP3/WMA and JPEG
When playing a disc contained with MP3/WMA and
JPEG files together, you can select which menu of files
you would like to play by pressing MENU.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
ID3 TAG
Playing an Audio CD or
MP3/WMA file
When playing a file containing information such as
track titles, you can see the information by pressing
DISPLAY. (Song, Artist, Album, Genre, Comment)
This unit can play Audio CDs or MP3/WMA files.
MP3/ WMA/ Audio CD
Once you insert an MP3/WMA files recording media or
Audio CD a menu appears on the TV screen.
Press v / V to select a track/file and then press PLAY
or ENTER, and playback starts. You can use variable
playback functions. Refer to the page 14.
MP3 / WMA disc compatibility with this player is
limited as follows:
• Sampling frequency: within 32 - 48 kHz (MP3),
within 32 - 48kHz (WMA)
• Bit rate: within 32 - 320kbps (MP3), 40 - 192kbps
(WMA)
• The DVD/CD Receiver cannot read an MP3/WMA file
that has a file extension other than “.mp3” / “.wma”.
• CD-R physical format should be ISO 9660
• If you record MP3 / WMA files using software that
cannot create a file system (eg. Direct-CD) it is
impossible to playback MP3 / WMA files.We recommend
that you use Easy-CD Creator, which creates an ISO
9660 file system.
• File names should have a maximum of 8 letters and
must incorporate an .mp3 or .wma extension.
• They should not contain special letters such as / ? * : “
< > l etc.
• The total number of files on the disc should be less than
999.
This DVD/CD Receiver requires discs and recordings to
meet certain technical standards in order to achieve
optimal playback quality. Pre-recorded DVDs are
automatically set to these standards. There are many
different types of recordable disc formats (including CD-R
containing MP3 or WMA files) and these require certain
pre-existing conditions (see above) to ensure compatible
playback.
Customers should note that permission is required in
order to download MP3 / WMA files and music from
the Internet. Our company has no right to grant such
permission. Permission should always be sought from
the copyright owner.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Repeat Programmed Tracks
Programmed Playback
The program function enables you to store your
Favourite tracks from any disc in the receiver memory.
A program can contain 30 tracks.
1. Press REPEAT when playing a disc. The repeat
icon appears.
2. Press REPEAT to select a desired repeat mode.
• Track: repeats the current track
• All: repeats all the tracks on programmed list.
• Off (No display): does not play repeatedly.
1. Insert a disc.
Audio CD and MP3/WMA Discs:
2. To add a music(s) on the program list, press
Erasing a Track from “Program” List
E
PROG/MEMO to enter the program edit mode (
mark appears on the menu).
1. Use v V to select the track that you wish to erase
from the Program list.
3. Select a desired music on the [List] by using the v
/ V then press ENTER to add the music to the
program list.
2. Press CLEAR in program edit mode.
Erasing the Complete Program List
Use v / V to select [Clear All] then press ENTER in
program edit mode.
4. Select music from the program list then press
ENTER to start programmed playback.
Note:
The programs are also cleared when the disc is removed,
the unit is switched to power off or the function is switched to
others.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Still Picture
Viewing a JPEG file
This unit can play discs with JPEG files.
Before playing JPEG recordings, read the notes on
JPEG Recordings on the right.
1. Press PAUSE (X) during the slide show.
The DVD/CD Receiver will now go into the PAUSE
(X) mode.
2. To return to the slide show, press PLAY or press
PAUSE (X) again.
1. Insert a disc and close the tray.
The PHOTO menu appears on the TV screen.
Moving to another File
Press SKIP (. or >) once during viewing a
picture to advance to the next or previous file.
Rotating the picture
Press v / V during showing a picture to rotate the
picture clockwise or counter-clockwise.
Listening to music during slide show
You can listen to music during slide show, if the disc
contain music and photo files together. Use v /V /b
/B to highlight (
) icon then press ENTER to start
slide show. This function is available only in disc.
About help menu
2. Press v / V to select a folder, and then press
ENTER. A list of files in the folder appears.
If you are in a file list and want to return to the
previous Folder list, use the v / V buttons on the
Menu
Buttons
Operation
v
/ V
v / V
Rotating the picture
b Prev./ B Next b / B
Moving to another file
remote to highlight
and press ENTER.
RETURN Closes the slide show
ENTER To hide the help menu
3. If you want to view a particular file, press v / V to
highlight a file and press ENTER or PLAY. While
viewing a file, you can press STOP to move to the
previous menu (JPEG menu).
Tips:
JPEG disc compatibility with this player is
limited as follows:
There are three Slide Speed options
Use v /V /b /B to highlight the Speed. Then, use b / B to
: 3s, 5s, 8s
select the option you want to use and then press ENTER.
• Depending upon the size and the number of
JPEG files, it could take a long time for the
DVD/CD Receiver to read the disc’s contents. If
you don’t see an on-screen display after several
minutes, some of the files may be too large —
reduce the resolution of the JPEG files to less
than 2M pixels as 2760 x 2048 pixels and burn
another disc.
Note:
Depending on the size and resolution of JPEG files, it may
take longer for slide show to be set.
Slide Show
1. Highlight the file (not folder) which you like
beginning to slide show.
2. Select the slide speed. (Refer to the tips this page)
• The total number of files and folders on the disc
should be less than 999.
3. Use v /V /b /B to highlight the
(Slide Show)
then press ENTER.
• Some discs may not operate due to a different
recording format or the condition of disc.
Note:
• The sequence of slide show is from top to down, cannot
be reverse.
• Ensure that all the selected files have the “.jpg”
extensions when copying into the CD layout.
• Slide show cannot repeat automatically, you could start the
slide show again manually.
• If the files have “.jpe” or “.jpeg” extensions, please
rename them as “.jpg” file.
• During slide show, a help menu appears in the lower part
of the screen. To hide this help menu, press ENTER or
DISPLAY. Then press this button again, a help menu
appears again.
• File names without “.jpg” extension will not be
able to be read by this DVD/CD Receiver. Even
though the files are shown as JPEG image files in
Windows Explorer.
• To close JPEG slide show, press RETURN or STOP (x).
18
Download from Www.Somanuals.com. All Manuals Search And Download.
“If you connect to the [VIDEO OUT] terminal on
this unit and switch TV input mode, you can enjoy
video playback.” - When you connect the unit and TV
to COMPONENT VIDEO OUT or HDMI OUT, connect
the unit and TV to VIDEO OUT (MONITOR).
Using iPod
For detial refer to iPod guide.
iPod mode: You can operate your iPod by using the
supplied remote control and directly control on your
iPod.
Compatible iPod
OSD iPod mode: You can operate your iPod by
controlling OSD menu on the TV screen with supplied
remote control. The controls on your iPod are not
operational in the OSD iPod mode.
• When the unit is connected with dock connector
may result in malfunctions
• Compatibility with your iPod may vary depending on
the type of your iPod.
• Depending on your iPod’s software version, it may
not be possible to control your iPod from the unit.
We recommend installing the latest software
version.
General operation
1. Connect the iPod and the unit with iPod docking
station. Refer to the page 7.
2. Turn the unit on.
Notes:
Your iPod is automatically turned on.
•
Interference may happen depending on iPod devices.
3. Press INPUT on the remote control to enter the
iPod mode.
• The video files are outputted only when you connect
the unit to VIDEO OUT (MONITOR).
• Connect the end on the cable with the marked “V“
facing downwards to rear on the unit.
• Be careful not to put iPod dock strongly into the unit
when connecting or disconnecting it. But the cable
may be damaged.
The iPod menu appears on the TV screen.
The initial screen of iPod menu is the OSD iPod
mode.
4. Use v / V and ENTER on the Remote Control to
display the list of menu.
5. Press ENTER to play.
• JVC is not responsible for any loss of data on an
iPod when used with this system.
• This system can receive analog sound from the
following iPod models and iPhone models
- iPod touch
General features
Pausing playback
Press PAUSE (X) or PLAY (B) to pause playback.
Press PAUSE (X) or PLAY (B) to continue playback.
- iPod classic
- iPod 5th generation
- iPod 4th generation
Skipping to the next/previous file
- iPod nano (1st/2nd/3nd generation)
- iPod mini (1st/2nd generation)
- iPhone 3G
Press SKIP (>) to move to the next file.
Press SKIP (.) to return to the beginning of the
current file.
Press SKIP (.) twice briefly to step back to the
previous file.
• This product support music and video only.
• If content on the iPod is not played back correctly,
update your iPod software to the latest version. For
details about updating the iPod, check the Apple
web site <http://www.apple.com>.
• Adjust the volume to a moderate level before you
connect your iPod and this unit.
Fast forward or fast reverse
During playback, press and hold SCAN (m or M)
and then release at a point you want.
Playing repeatedly
Press REPEAT repeatedly to select an item to be
repeated. The current file will be played back
repeatedly. To return to normal playback, press
REPEAT repeatedly. (On video files, this function is
not available.)
• “Made for iPod” means that an electronic accessory
has been designed to connect specifically to iPod
and has been certified by the developer to meet
Apple performance standards.
• “Works with iPhone” means that an electronic
accessory has been designed to connect
iPod message
“Please, check your iPod” - If the power of your
iPod is insufficient or the iPod is misconnected or
unknown device. Reset the iPod if the iPod is not
operating normally (Refer to
specifically to iPhone and has been certified by the
developer to meet Apple performance standards.
• Apple is not responsible for the operation of this
device or its compliance with safety and regulatory
standards.
http://www.apple.com/support/)
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Presetting the Radio Stations
Listening to the Radio
You can preset 50 stations for FM. Before tuning,
make sure that you have turned down the volume.
Preset radio stations in the DVD/CD Receiver’s
memory first (see “Presetting radio stations” on the
left).
1. Press FUNCTION on the remote control until FM
appears in the display window.
1. Press FUNCTION until FM appears in the display
window.
2. Press and hold TUNING.(-/+) for about two
seconds until the frequency indication starts to
The last received station is tuned in.
change, then release.
2. Press PRESET (-/+) repeatedly on the remote
Scanning stops when the DVD/CD Receiver tunes in a
station.
control to select the preset station you want.
Each time you press the button, the DVD/CD Receiver
tunes in one preset station at a time.
3. Press PROG./MEMO. on the remote control.
A preset number will flash in the display window.
3. Adjust the volume by rotating VOLUME on the
front panel or by pressing VOLUME + or - on the
remote control repeatedly.
4. Press PRESET (-/+) on the remote control to
select the preset number you want.
To turn off the radio
Press POWER to turn the DVD/CD Receiver off or
select another function mode.
5. Press PROG./MEMO. on the remote control again.
The station is stored.
6. Repeat steps 3 to 6 to store other stations.
To listen to non-preset radio stations
ꢀ Use manual or automatic tuning in the step 2.
To tune in a station with a weak signal
Press TUNING.(-/+) repeatedly in step 2 to tune in the
station manually.
ꢀ For manual tuning, press TUNING.(-/+) repeatedly.
ꢀ
For automatic tuning, press and hold TUNING.(-/+)
for about two seconds on the front panel.
To clear all the stored stations
Press and hold PROG./MEMO. for about two seconds
and “ERASE ALL” is appeared in the display window
and then press PROG./MEMO. again, the stations are
cleared.
To select a preset radio station directly
You can use the number buttons on the remote
control to select a preset radio station directly.
For example, to listen to the preset station 4, press 4
on the remote control. To listen to the preset station
19, press 1 and then 9 (within 3 seconds).
ꢀ If you have accidentally entered into the "ERASE
ALL" mode and you do not wish to clear the
memory, do not press any key. After a few seconds,
"ERASE ALL" will go off by itself and change to
normal mode.
For your reference
ꢀ If an FM program is noisy
Pour afficher « STEREO », appuyez sur FM
MODE. Appuyez à nouveau sur ce bouton pour
afficher « MONO ». L’effet stéréo est supprimé,
mais la réception est meilleure. Appuyez à
nouveau sur le bouton pour rétablir l’effet stéréo.
Note:
If all stations have already been entered, the FULL
message will appear in the display window for a
moment and then a preset number will flash.
To change the preset number, follow the steps 4-5 as
above.
ꢀ To improve reception
Reorient the supplied antennas.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Sleep Timer Setting
Press SLEEP/DIMMER one or more times to select
delay time between 10 and 180 minutes, after the
player will turn off.
To check the remaining time, press SLEEP/DIMMER
To cancel the sleep function, press SLEEP/DIMMER
repeatedly until “SLEEP 10” appears, and then press
SLEEP/DIMMER once again while “SLEEP 10” is
displayed.
Enjoying audio form an external
source
You can enjoy audio form an external source through
your unit.
Press INPUT repeatedly to select the desired input
source. - AUX, AUX OPT, AUDIO IN, HDMI IN, OSD
IPOD, IPOD
Setting the surround mode
This system has a number of pre-set surround sound
fields. You can select a desired sound mode by using
SOURROUND. You can change the SOURROUND
using b /B arrow key while the SOURROUND
information is displayed on.
Note:
You can check the remaining time before the DVD/CD
Receiver turns off.
Press SLEEP/DIMMER. The remaining time appears
in the display window.
The displayed items for the Equalizer may be different
depending on sound sources and effects.
Dimmer
[[PLII MOVIE/ PLII MUSIC/ PLII MTRX(matrix)] Dolby
Pro Logic II enables you to play stereo source on 5.1-
channel.
[Bypass] You can enjoy the sound without equalizer
effect.
Press SLEEP/DIMMER once. The LED (Light-emitting
diode) of front panel is turned off and the display
window will be darken by half. To cancel it, press
SLEEP/DIMMER repeatedly until dim off.
Muting
Press MUTING to mute your unit.
Notes:
•
In some of surround modes, some speakers maybe
no sound or low sound, it depends on the mode of
surround and the source of audio, it is not defective.
You can mute your unit in order, for example, to
answer the telephone, the “MUTING” indicator flickers
in the display window.
• You may need resetting the surround mode, after
switch the input, sometimes even after the sound
track changed.
Note:
This muting doesn’t affect the audio output to HDMI; it
only mutes the output of speakers connected to the
unit.
Setting the disc ejection lock
You can lock the disc tray to prevent the disc form
being ejected.
When the main unit is turned off, hold down the STOP
key at the front panel for 5 seconds
If you attempt to open the disc tray by pressing
OPEN/CLOSE key, the disc tray does not open and
“LOCKED” appears in the display window.
To cancel the disc ejection lock, hold down the STOP
key at the front panel for 5 seconds again when the
main unit is turned off.
“UNLOCKED” is displayed in the display window.
Note:
Before the main unit is turned off, DVD/CD function
should be selected.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Language Codes
Use this list to input your desired language for the following initial settings:
Disc Audio, Disc Subtitle, Disc Menu.
Language
Abkhazian
Afar
Afrikaans
Albanian
Ameharic
Arabic
Armenian
Assamese
Aymara
Azerbaijani
Bashkir
Basque
Bengali; Bangla
Bhutani
Bihari
Breton
Bulgarian
Burmese
Byelorussian
Cambodian
Catalan
Chinese
Corsican
Croatian
Czech
Code
6566
6565
6570
8381
6577
6582
7289
6583
6588
6590
6665
6985
6678
6890
6672
6682
6671
7789
6669
7577
6765
9072
6779
7282
6783
6865
7876
6978
6979
6984
7079
Language
Fiji
Finnish
French
Frisian
Galician
Georgian
German
Greek
Greenlandic
Guarani
Gujarati
Hausa
Code
7074
7073
7082
7089
7176
7565
6869
6976
7576
7178
7185
7265
7387
7273
7285
7383
7378
7365
7165
7384
7465
7487
7578
7583
7575
7589
7579
7585
7679
7665
7686
Language
Lingala
Lithuanian
Macedonian
Malagasy
Malay
Malayalam
Maltese
Maori
Code
7678
7684
7775
7771
7783
7776
7784
7773
7782
7779
7778
7865
7869
7879
7982
8065
8083
7065
8076
8084
8185
Language
Singhalese
Slovak
Slovenian
Somali
Spanish
Sudanese
Swahili
Swedish
Tagalog
Tajik
Code
8373
8375
8376
8379
6983
8385
8387
8386
8476
8471
8465
8484
8469
8472
6679
8473
8479
8482
8475
8487
8575
8582
8590
8673
8679
6789
8779
8872
7473
8979
9085
Marathi
Moldavian
Mongolian
Nauru
Nepali
Norwegian
Oriya
Panjabi
Pashto, Pushto
Persian
Polish
Portuguese
Quechua
Rhaeto-Romance 8277
Rumanian
Russian
Samoan
Sanskrit
Scots Gaelic
Serbian
Serbo-Croatian
Shona
Tamil
Tatar
Hebrew
Hindi
Telugu
Thai
Tibetan
Tigrinya
Tonga
Turkish
Turkmen
Twi
Ukrainian
Urdu
Hungarian
Icelandic
Indonesian
Interlingua
Irish
Italian
Japanese
Javanese
Kannada
Kashmiri
Kazakh
Kirghiz
8279
8285
8377
8365
7168
8382
8372
8378
8368
Uzbek
Vietnamese
Volapük
Welsh
Wolof
Xhosa
Yiddish
Yoruba
Zulu
Danish
Dutch
English
Esperanto
Estonian
Faroese
Korean
Kurdish
Laothian
Latin
Latvian, Lettish
Sindhi
Area Codes
Choose a area code from this list.
Area
Code
AF
AR
AU
AT
Area
Ethiopia
Fiji
Finland
France
Germany
Great Britain
Greece
Greenland
Code
ET
FJ
Area
Code
MY
MV
MX
MC
MN
MA
NP
Area
Saudi Arabia
Senegal
Singapore
Slovak Republic
Slovenia
South Africa
South Korea
Spain
Sri Lanka
Sweden
Switzerland
Taiwan
Thailand
Turkey
Code
SA
SN
SG
SK
SI
Afghanistan
Argentina
Australia
Austria
Belgium
Bhutan
Bolivia
Brazil
Cambodia
Canada
Chile
China
Colombia
Congo
Costa Rica
Croatia
Czech Republic
Denmark
Ecuador
Egypt
Malaysia
Maldives
Mexico
Monaco
Mongolia
Morocco
Nepal
Netherlands
Netherlands Antilles AN
New Zealand
Nigeria
Norway
FI
FR
DE
GB
GR
GL
BE
BT
ZA
BO
BR
KH
CA
CL
CN
CO
CG
CR
HR
CZ
DK
EC
EG
SV
KR
ES
LK
NL
Heard and McDonald Islands HM
Hong Kong
Hungary
India
Indonesia
Israel
Italy
Jamaica
Japan
Kenya
Kuwait
Libya
Luxembourg
HK
HU
IN
ID
IL
NZ
NG
NO
OM
PK
PA
PY
PH
PL
SE
CH
TW
TH
TR
UG
UA
US
UY
UZ
VN
ZW
Oman
Pakistan
Panama
Paraguay
Philippines
Poland
Portugal
Romania
Russian Federation RU
IT
Uganda
Ukraine
United States
Uruguay
Uzbekistan
Vietnam
JM
JP
KE
KW
LY
LU
PT
RO
El Salvador
Zimbabwe
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Check the following guide for the possible cause of a problem before contacting service.
Correction
Cause
Symptom
No power.
• Plug the power cord securely into the
wall outlet.
• The power cord is disconnected.
• Insert a disc. (Check that the DVD or,
audio CD indicator in the DVD display
is lit.)
• No disc is inserted.
The power is on, but
the DVD/CD Receiver
does not work.
• Select the appropriate video input
mode on the TV so the picture from
the DVD/CD Receiver appears on the
TV screen.
• The TV is not set to receive DVD signal
output.
No picture.
• Connect the video cable into the
jacks securely.
• The video cable is not connected
securely.
• Turn on the TV.
• The connected TV power is turned off.
There is no sound or
only a very low-level
sound is heard.
• Select the correct input mode of the
audio receiver so you can hear the
sound from the DVD/CD Receiver.
• The equipment connected with the
audio cable is not set to receive DVD
signal output.
• Connect the audio cable into the
jacks securely.
• The audio cables are not connected
securely.
• Turn on the equipment connected
with the audio cable.
• The power of the equipment connected
with the audio cable is turned off.
• Replace it with new one.
• Clean the disc.
• The audio connecting cable is damaged.
• The disc is dirty.
The playback picture is
poor.
• Insert a disc. (Check that the DVD, or
audio CD indicator in the DVD display
is lit.)
The DVD/CD Receiver • No disc is inserted.
does not start playback.
• Insert a playable disc. (Check the
disc type, colour system and Regional
code.)
• An unplayable disc is inserted.
• Place the disc with the playback side
down.
• The disc is placed upside down.
• Place the disc on the disc tray
correctly inside the guide.
• The disc is not placed within the guide.
• Clean the disc.
• The disc is dirty.
• Press the SETUP button to turn off
the menu screen.
• A menu is on the TV screen.
• Cancel the Rating function or change
the rating level.
• The Rating level is set.
• Clean the disc.
Loud hum or noise is
heard.
• The disc is dirty.
• Connect the speakers and
components securely.
• The speakers and components are
connected poorly.
• Move your TV away from the audio
components.
• The DVD/CD Receiver is located too
close to the TV.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Cause
Correction
Symptom
• The antenna is positioned or connected
poorly.
• Connect the antenna securely.
Radio stations cannot
be tuned in.
• Adjust the antennas and connect an
external antenna if necessary.
• The signal strength of the stations is too
weak (when tuning in with automatic
tuning).
• Tune in the station manually.
• No stations have been preset or preset
stations have been cleared (when
tuning by scanning preset stations).
• Preset the stations (page 20).
• The remote control is not pointed at the • Point the remote control at the remote
The remote control
does not work
properly.
remote sensor of the DVD/CD Receiver.
sensor of the DVD/CD Receiver.
• The remote control is too far from the
DVD/CD Receiver.
• Use the remote control within about 23
ft (7 m).
• There is an obstacle in the path of the
remote control and the DVD/CD
Receiver.
• Remove the obstacle.
• The batteries in the remote control are
flat.
• Replace the batteries with new ones.
• Press DIMMER on the remote control.
• Nothing is displayed on the front panel
display.
The front panel
display is too dim.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Power supply
Power consumption
120 V ~ 60 Hz
130 W
Net Weight
3.6 kg
430 x 76 x 317 mm
Temperature: 5°C to 35°C, Operation status: Horizontal
5% to 85%
External dimensions (W x H x D)
Operating conditions
Operating humidity
Laser
Video system
Semiconductor laser, wavelength 650 nm
NTSC
Frequency response (audio)
Signal-to-noise ratio (audio)
Dynamic range (audio)
Harmonic distortion (audio)
Video output
140 Hz to 20 kHz ꢁ
More than 75 dB (1 kHz, 20 kHz LPF/A-Filter) ꢁ
More than 75 dB ꢁ
0.5 % (1 kHz, at 1W position) (20 kHz LPF) ꢁ
1.0 V (p-p), 75 Ω, negative sync., RCA jack x 1
(Y) 1.0 V (p-p), 75 ohms, negative sync, RCA jack x 1
(PB)/(PR) 0.7 V (p-p), 75 ohms, RCA jack x 1
480i/480p/720p/1080i/1080p
COMPONENT VIDEO OUT
HDMI OUT
Tuning Range
87.5 - 108.0 MHz
Intermediate Frequency
Signal-to Noise Ratio
Frequency Response
Stereo mode
10.7 MHz
60 dB (Mono) ꢁ
140 - 10,000 Hz ꢁ
155 W + 155 W (4Ω at 1 kHz, THD 10 %)
Front: 155 W + 155 W (THD 10 %)
center*: 155 W
Surround*: 155 W + 155 W (4Ω at 1 kHz, THD 10 %)
Subwoofer*: 225 W (3Ω at 70 Hz, THD 10 %)
AUDIO IN, OPTICAL IN, AUX IN, iPod, HDMI IN
MONITOR OUT, HDMI OUT,
Surround mode
(* Depending on the sound mode
settings and the source, there
may be no sound output.)
Inputs
Outputs
COMPONENT VIDEO OUT
Front/Rear Speaker
1 Way 1 Speaker
4 Ω
Center speaker
1 Way 1 Speaker 1 Way 1 Speaker
Passive Subwoofer
Type
Impedance
4 Ω
3 Ω
Frequency Response
Sound Pressure Level
Rated Input Power
120 - 18000 Hz
83 dB/W (1m)
155 W
120 -18000 Hz
83 dB/W (1m)
155 W
40 - 1500 Hz
82 dB/W (1m)
225 W
Max. Input Power
Net Dimensions (W x H x D)
Net Weight
310 W
113 x 209 x 83 mm
0.78 kg
310 W
450 W
301 x 118 x 83 mm 236 x 435 x 391 mm
0.9 kg 5.7 kg
Items with ꢁ are measured at Front Speaker Terminals in STEREO mode
Supplied Accessories
FM Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . .x1
Speaker cable . . . . . . . . . . . . . . . . . . . . . . . . . . .x6
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . .x1
Video RCA cable . . . . . . . . . . . . . . . . . . . . . . . . .x1
iPod Docking station . . . . . . . . . . . . . . . . . . . . . .x1
Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .x2
❋ Designs and specifications are subject to change without notice.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
2009 Victor Company of Japan, Limited
0409SKMLGEEGL
Download from Www.Somanuals.com. All Manuals Search And Download.
|