JVC Computer Monitor DT V17L3DY User Manual

The lightning flash with arrowhead  
symbol, within an equilateral triangle is  
intended to alert the user to the presence  
of uninsulated “dangerous voltage”  
within the product’s enclosure that may  
be of sufficient magnitude to constitute a  
risk of electric shock to persons.  
CAUTION  
RISK OF ELECTRICAL SHOCK  
DO NOT OPEN  
The exclamation point within an  
equilateral triangle is intended to alert  
the user to the presence of important  
operating and maintenance (servicing)  
instructions in the literature  
To reduce the risk of electric shock. Do  
not remove cover (or back). No user  
serviceable parts inside. Refer servicing  
to qualified service personnel.  
CAUTION:  
accompanying the appliance.  
DT-V17L3DY  
INSTRUCTIONS  
Table of Contents  
MULTI FORMAT LCD MONITOR  
Safety Precautions .............................................. 2  
IMPORTANT SAFEGUARDS ........................... 2  
Installation............................................................ 4  
Daily Operations / Connections ......................... 6  
Front panel ....................................................... 6  
Rear panel........................................................ 8  
Available signals............................................... 9  
Menu Configuration—MAIN MENU .................. 10  
Menu Configuration—SET-UP MENU............... 14  
External Control................................................. 16  
About the external control .............................. 16  
Using the MAKE/TRIGGER system ............... 17  
Using the serial communication ..................... 18  
Troubleshooting................................................. 19  
Self-check program ........................................ 20  
Maintenance....................................................... 20  
Specifications .................................................... 21  
General........................................................... 21  
Input/output terminals..................................... 21  
Dimensions..................................................... 22  
LCT2500-001A-H  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FCC NOTICE  
IMPORTANT SAFETY INSTRUCTIONS  
CAUTION: Changes or modifications not approved by JVC could void the user’s authority to operate the  
equipment.  
1) Read these instructions.  
2) Keep these instructions.  
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device,  
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against  
harmful interference when the equipment is operated in a commercial environment. This equipment generates,  
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction  
manual, may cause harmful interference to radio communications. Operation of this equipment in a residential  
area is likely to cause harmful interference in which case the user will be required to correct the interference at  
his own expense.  
3) Heed all warnings.  
4) Follow all instructions.  
5) Do not use this apparatus near water.  
6) Clean only with dry cloth.  
7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.  
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including  
amplifiers) that produce heat.  
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one  
wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the  
third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for  
replacement of the obsolete outlet.  
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point  
where they exit from the apparatus.  
11) Only use attachments/accessories specified by the manufacturer.  
12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or  
sold with the apparatus. When a cart is used, use caution when moving the cart/  
apparatus combination to avoid injury from tip-over.  
13) Unplug this apparatus during lightning storms or when unused for long periods of time.  
14) Refer all servicing to qualified service personnel. Servicing is required when the  
apparatus has been damaged in any way, such as power-supply cord or plug is  
damaged, liquid has been spilled or objects have fallen into the apparatus, the  
apparatus has been exposed to rain or moisture, does not operate normally, or has  
been dropped.  
IMPORTANT RECYCLING INFORMATION  
This product has a fluorescent lamp that contains mercury. Disposal of these materials  
may be regulated in your community due to environmental considerations. For disposal  
or recycling information, please contact your local authorities or for USA, the Electronic  
WARNING: TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS  
APPARATUS TO RAIN OR MOISTURE.  
WARNING: THIS APPARATUS MUST BE CONNECTED TO A MAINS SOCKET OUTLET  
WITH A PROTECTIVE EARTHING CONNECTION.  
CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED.  
REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE.  
15) Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be  
placed on the apparatus.  
16) Batteries shall not be exposed to excessive heat such as sunshine, fire or the like.  
17) When discarding batteries, environmental problems must be considered and the local rules or laws governing the  
disposal of these batteries must be followed strictly.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
4
Installation  
• Do not rest your arm on the monitor or lean against the monitor.  
• Do not touch the LCD panel when installing the monitor.  
• Be sure to install the monitor securely to prevent the monitor from falling over, which may cause damage to the monitor  
or injury.  
CAUTION  
To detach the stand  
CAUTION  
Lay the monitor on a cloth with the LCD panel facing down to prevent the LCD panel from being damaged.  
You can place the monitor in the following two ways when using it on the supplied stand.  
Attachment screws  
You can tilt the monitor as follows.  
When the stand plate is attached to the higher  
position of the stand body (To adjust the stand  
height” on page 5), you can place the monitor as  
illustrated below.  
Screw holes for stand attachment  
Monitor  
Stand body  
1 Remove the screws on the right side of the stand  
(see the illustration below), then lift the stand up  
by about 144°.  
About  
144°  
About 12°  
0°  
About 8°  
Stand  
Screw  
(silver)  
• When the monitor is not tilted (0°), the  
guidelines align as illustrated below.  
Monitor  
Guidelines  
2 Attach the removed screws and place the monitor  
as illustrated below.  
To install the stand  
When attaching the stand to the monitor, insert the guides of the stand into the guide holes on the monitor to  
place the stand in the correct position. Then fix the stand firmly with the attachment screws.  
You can select the stand height—higher position  
or lower position (To adjust the stand height” on  
page 5).  
Guide holes  
To place the monitor as illustrated on the left again,  
remove the screws on the right side of the stand,  
return the monitor angle to 0°, then reattach the  
removed screws.  
CAUTION  
• Be careful not to pinch your fingers in the gap between  
the monitor and the stand.  
• When the stand plate is attached to the lower  
position of the stand body, you cannot tilt the monitor  
downward.  
Guides  
Screw holes  
for stand  
CAUTION  
• When lifting up the stand...  
attachment  
– lay the monitor on a cloth with the LCD panel  
facing down to prevent the LCD panel from being  
damaged.  
Monitor  
Stand plate  
– be careful not to pinch your fingers in the moving  
parts.  
• Make sure of lifting the stand up until it stops (about  
144°); otherwise the monitor may fall over.  
• Place the monitor on a mat to avoid scratching the  
table surface.  
Stand body  
• Do not lift up the stand when the stand plate is  
attached to the lower position of the stand body.  
• When the battery is attached, the stand may not be  
lifted up depending on the type of the battery.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
To adjust the stand height  
To change the stand height, detach the stand from the monitor (To detach the stand” on page 4). Then,  
change the position of the stand plate according to the stand height you want by choosing the screw holes to use.  
To prevent an accidental fall  
Fix the monitor to a wall by using strings.  
Fixing the monitor  
Attach the hook (not provided) to the VESA mounting holes on the rear panel (use the two holes on the upper  
side) using M4 x 10 mm screws (not provided). Bind the hooks on the rear panel of the monitor to a wall or a pillar  
using durable string.  
<Higher position>  
<Lower position>  
Screw holes for higher position  
Screw holes for lower position  
Stand plate  
Stand plate  
VESA mounting holes  
Stand body  
Stand body  
Hook and screw (M4 x 10 mm)  
(not provided)  
Hook (not provided)  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
6
Daily Operations / Connections  
7 Front panel  
• “NO EFFECT” is displayed when you press a button which is not available for the current input or signal format (the lamp lights even when the function does not  
actually work).  
Tally lamp  
• The items controlled by the MAKE system cannot be controlled by the buttons on the front panel (“REMOTE ON” is displayed and the lamps do not light).  
This lamp is controlled by the tally function of the  
MAKE/TRIGGER terminal.  
You can select the color of the tally lamp from  
GREEN” or “RED”.  
TALLY SELECT” in “FUNCTION SETTING” on  
page 14 and “External Control” on page 16  
5
/
/
/
buttons  
q SCREENS CHECK button/lamp  
Displays only the selected element (R, G, or B) of  
the video signal.  
y Power lamp  
When a menu screen is displayed  
Selects or adjusts menu items. (“Menu  
Operations” on page 7)  
When no menu screen is displayed  
Selects the audio channels of EMBEDDED AUDIO  
signals. (“Audio Channel Selection” on page 7)  
Unlit: The monitor is completely off (both the  
POWER switch and DC switch on the rear panel  
are turned off).  
• Each time you press this button, the screen  
changes in the following order.  
Lights in Green: The monitor is on.  
Lights in orange: The monitor is off (on standby).  
Flashes in orange: The monitor is in the P. SAVE  
(power save) mode (“NO SYNC ACTION” in  
“SYNC FUNCTION” on page 13).  
RGB (Normal screen)  
Blue screen  
Red screen  
Green screen  
Pressing  
SET-UP MENU. (  
6 MENU button  
button while holding button displays the  
“Menu Operations” on page 7)  
w ASPECT button/lamp  
Changes the aspect ratio of the picture from 4:3  
to 16:9 when the picture of 16:9 aspect ratio is  
squeezed into 4:3 format signal.  
To return to 4:3, press the button again.  
• This function does not work when displaying the  
picture in the 1:1 mode.  
u
button  
Activates/deactivates the display of the MAIN MENU.  
(“Menu Operations” on page 7)  
Turns on and off (on standby) the monitor.  
• The power switches (the POWER switch and DC  
switch) are equipped on the rear panel of the  
monitor (p, w on page 8).  
To turn off the monitor completely, turn off the  
POWER switch and DC switch.  
7 COLOR OFF button/lamp  
Displays only the luminance signal.  
• This function does not work for RGB input signals.  
1 Speakers (stereo)  
The speakers emit the same audio signal emitted  
from the AUDIO (MONITOR OUT) terminals.  
(5 AUDIO (MONITOR OUT) terminals” on  
page 8)  
e WAVE FORM button/lamp  
8 1:1 button/lamp  
Displays/hides the indication of the wave form  
monitor.  
• Adjust the settings of the wave form monitor in  
“WAVE FORM SETTING” of the MAIN MENU  
(page 13).  
i DC lamp  
When the DC 12 V power voltage is being lowered  
Displays the picture in the original resolution of the  
input signal.  
• The aspect ratio of the picture may change  
depending on the input signal.  
due to the battery consumption, the lamp changes  
to orange from green. When the voltage becomes  
lower than a certain level, the monitor automatically  
turns off and the lamp turns to red.  
• Make sure to turn off the POWER switch and  
DC switch on the rear panel before replacing the  
battery.  
• The length of time that the lamp lights in orange  
differs depending on the type of battery or the  
battery condition. It is recommended to replace  
the battery when the lamp turns to orange.  
2 VOLUME adjustment knob  
Adjusts the volume.  
9 AREA MARKER button/lamp  
Displays/hides the area marker.  
3 Picture adjustment knob  
• The closed caption (page 13) disappears when  
the wave form monitor is displayed.  
PHASE: Adjusts the picture hue.  
• Select the style of the area marker in “MARKER”  
of the MAIN MENU (page 11).  
• This function works only when displaying the  
picture in 16:9 aspect ratio.  
• This function does not work when “AREA  
MARKER” or “R-AREA MARKER” is set to “OFF”  
in “MARKER.”  
CHROMA: Adjusts the picture color density.  
BRIGHT: Adjusts the picture brightness.  
CONTRAST: Adjusts the picture contrast.  
r T.C. (time code) button/lamp  
Activates/deactivates the display of the time data  
(time code) contained in the SDI signal.  
(“On the Information Display” on page 7)  
4 MUTING button  
Turns off the sound when no menu screen is  
displayed.  
t INPUT SELECT buttons/lamps  
Selects an input.  
To cancel the function, press the button again or  
turn the VOLUME adjustment knob.  
• Muting function is also canceled when  
“BALANCE” of “AUDIO SETTING” in the MAIN  
MENU is changed (page 12).  
SDI 1: E. AUDIO HD/SD SDI (IN 1) terminal  
SDI 2: E. AUDIO HD/SD SDI (IN 2) terminal  
DVI: DVI-D (HDCP) terminal  
COMPO.: COMPO. terminal  
VIDEO: VIDEO terminal  
p SAFETY MARKER button/lamp  
Displays/hides the safety marker.  
• Adjust the area of the safety marker in “MARKER”  
of the MAIN MENU (page 11).  
• This function does not work when displaying the  
picture in the 1:1 mode.  
• The lamp for the selected input lights.  
• This function does not work when “SAFETY  
MARKER” or “R-SAFETY MARKER” is set to  
“OFF” in “MARKER.”  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu Operations  
Audio Channel Selection  
On the Information Display  
On the Status Display  
Select audio channels emitted from the speakers  
(L/R) and the AUDIO (MONITOR OUT) (OUT1(L)/  
OUT2(R)) terminals, when EMBEDDED AUDIO  
signals come in to the E. AUDIO HD/SD SDI  
terminal (IN1 or IN2) and SDI input (1 or 2) is  
selected.  
You have to choose a group of selectable audio  
channels before the channel selection (☞  
“E.AUDIO GROUP” in “AUDIO SETTING” on  
page 12).  
The monitor displays the information below.  
• Make the setting to display/hide each  
information using the MENU with the exception  
of 5, controlled with T.C. button (r on page  
6).  
• Select the position of the information display  
(“POSITION” in “INFORMATION” on page  
15).  
If you press the INPUT SELECT button (t on  
page 6) currently lit, the status of the input signal  
and setting of muting are displayed for about 3  
seconds.  
• Make the setting to display/hide the status in  
“STATUS DISPLAY” of the “INFORMATION” (☞  
page 15).  
• When “STATUS DISPLAY” is set to “AUTO” or  
“ON,the status below is also displayed in the  
following cases:  
1 Display the menu.  
To display the MAIN MENU  
\
Press MENU button.  
To display the SET-UP MENU  
\
Press button while holding button.  
MAIN MENU  
Selected item  
• The setting is memorized for each input (SDI 1  
and SDI 2).  
– When you change the input  
– When the signal condition of the current input  
changes  
Operation guide  
SET-UP MENU  
1 Press or button when a menu  
– When you turn on the monitor  
1 Audio level meter  
• When “STATUS DISPLAY” is set to “ON,the  
signal format will remain displayed 3 seconds  
after the status is displayed.  
is not displayed.  
• Not displayed when “LEVEL METER ch” is  
set to “OFF.” (“AUDIO SETTING” on page  
12)  
The screen for audio channel selection is  
displayed.  
• The screen for audio channel selection  
automatically disappears in about 30  
seconds after the previous operation.  
Selected item  
2 Signal format  
• Displayed when “STATUS DISPLAY” is set to  
“ON.(“INFORMATION” on page 15)  
• For the contents displayed, see “On the  
signal format” below and “Available signals”  
on page 9.  
Audio channel selection screen  
Operation guide  
1 Signal format  
Selected item  
• For the contents displayed, see “On the  
signal format” below and “Available signals”  
on page 9.  
2 Press  
buttons to select an item,  
then press button.  
3 Source name assigned in “CHARACTER  
SET.”  
• For some items, adjustments will be made by  
pressing  
• Displayed when “SOURCE ID” is set to “ON.”  
• Displayed in large letters when “STATUS  
DISPLAY” is set to “OFF” or “AUTO.”  
“INFORMATION” on page 15  
4 CRC error indication  
2 Signal format of DVI input  
“DVI INPUT SEL.on page 10  
3 Setting of “MUTING”  
.
2 Press  
buttons to select the left  
buttons to select an  
(L ch) or right (R ch).  
• Displayed only when muting is activated.  
4 MUTING button” on page 6  
3 Press  
• Displayed when “CRC ERROR” is set to  
“ON.(“INFORMATION” on page 15)  
• A red square is displayed when an error  
occurs.  
audio channel.  
• Each time you press the button, the audio  
channel changes according to the settings of  
“E.AUDIO GROUP” (“NOTE” on page 12).  
On the signal format  
The following messages appear depending on the  
type of input signals and their conditions.  
Ex.: When “MARKER” in the MAIN  
MENU is selected  
5 Time code  
• When the input signal includes no time code,  
“TC – –:– –:– –:– –” is displayed.  
r T.C. (time code) button/lamp” on page 6  
4 Press MENU button.  
The screen for audio channel selection  
disappears.  
When a DVI-D signal protected with HDCP is input  
3 Press  
then press  
adjustments.  
buttons to select an item,  
\
*” (at the end of the indication)  
When no video signal comes in  
“NO SYNC”  
When a noncompliant video signal comes in  
“Out of range”  
buttons to make  
• When any information of 1, 2, 3, or 4  
above is displayed while signals come in from  
equipment other than a computer, the picture is  
displayed without overlapping the information  
display area.  
However, the information display will overlap  
with the picture when...  
– displaying the picture with higher resolution  
than the resolution of the panel in 1:1 mode.  
– “SD4:3 LARGE” setting is “ON.”  
\
4 Press MENU button to finish the  
Using the audio level meter  
\
menu operation.  
You can check the conditions of the current  
EMBEDDED AUDIO signals in the audio level meter.  
(“On the Information Display” on the right, “LEVEL  
METER SETTING” in “AUDIO SETTING” on page  
12).  
When “COLOR SYSTEM” (“FUNCTION  
• Pressing MENU button repeatedly  
deactivates the display of the menu.  
SETTING” on page 14) is set to “AUTO” and the  
noncompliant composite video signals come in  
\
“OTHERS”  
(“FUNCTION SETTING” on page 14).  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
8
Daily Operations / Connections (cont.)  
7 E. AUDIO HD/SD SDI (SWITCHED OUT) terminal  
(BNC)  
w POWER switch  
7 Rear panel  
Turns AC power on or off.  
You need to press button (u on page 6)  
to use the monitor after turning on the POWER  
switch.  
CAUTION  
Do not connect the  
Carry handle  
Use this handle when carrying the monitor.  
Output terminal for the HD/SD SDI signals.  
• The SDI signals of the current input (SDI 1 or SDI  
2) are re-clocked, then emitted.  
• When an input other than SDI 1 and SDI 2 is  
selected, the SDI signal of the input selected last  
time is emitted from this terminal.  
• The signals are emitted from this terminal only  
when the monitor is on or in “P.SAVE” (power  
save) mode.  
power cord until all  
other connections are  
completed.  
e Screw holes for external battery attachment  
Attach external battery for DC 12 V power supply  
by using 2 screw holes. Choose the appropriate  
screw holes from 1, 2, 3 or 4, according to the type  
of external battery.  
• Use the Anton Bauer Dionic 90 (mount: QR DXC-  
M3A) external battery.  
8 DVI-D (HDCP) terminal  
Input terminal for the DVI-D signal compatible with  
HDCP.  
• When the picture is not displayed correctly,  
change the setting of “DVI INPUT SEL.”  
(page 10).  
CAUTION  
Do not use the external battery for DC 24 V  
power supply.  
• Use only the battery specified above. If a heavy  
battery is used, it may fall off depending on the  
way the monitor is used.  
• When an external battery is attached, attach the  
ferrite core (provided) to the power cord from the  
mount as illustrated below.  
9 DC IN 12V terminal  
DC 12 V (maximum  
DC 17 V) power input  
connector.  
1 REMOTE terminal  
Terminal for controlling the monitor by an external  
control. (“External Control” on page 16)  
2 VIDEO terminals (BNC)  
When using DC 12 V power (maximum DC 17 V),  
check the DC IN 12V terminal pin signal, and use  
the correct polarity. If the polarity is reversed, this  
could cause a fire or personal injury.  
Ex.: When the Anton Bauer mount (QR DXC-M3A) is used  
Input (IN) and output (OUT) terminals for the  
composite video signals.  
e
r
3 COMPO. (Y, PB/B-Y, PR/R-Y) terminals (BNC)  
Input (IN) and output (OUT) terminals for the analog  
component video (color difference) signals.  
• While using both the AC and DC 12 V power  
supply, AC power supply is preferentially used. If  
the AC power supply is cut off (for example, when  
turning off the POWER switch), the power supply  
automatically switches to the DC 12 V power  
supply.  
4 AUDIO (IN) terminals (pin jack)  
Input terminals for the analog audio signals.  
• Use this terminal for the analog audio connection  
of the SDI.  
Ferrite core  
5 AUDIO (MONITOR OUT) terminals (pin jack)  
Output terminals for the analog audio signal.  
• The terminals emit the audio signals through  
the AUDIO (IN) terminal or EMBEDDED AUDIO  
signals through the E. AUDIO HD/SD SDI (IN 1 or  
IN 2) input terminal.  
p DC switch  
r Security slot  
Turns the DC 12 V power on or off.  
Attach a security wire to this slot.  
You need to press  
button (u on page  
6) on the front panel to turn on the monitor after  
turning on the DC switch.  
Note for connections  
• The monitor consumes the battery even while the  
monitor is on standby. To save battery life, turn off  
the DC switch.  
• The signal is output from this terminal only  
when the monitor is on or in “P.SAVE” (power  
save) mode. (“NO SYNC ACTION” in “SYNC  
FUNCTION” on page 13)  
• Before making any connections, turn off all the  
equipment.  
• Use a cord whose plugs correctly match the  
terminals on this monitor and the equipment.  
• Plugs should be firmly inserted; poor connections  
could cause noise.  
• When unplugging a cord, be sure to grasp its plug  
and pull it out.  
• DO NOT connect the power cord until all connections  
are complete.  
q AC IN terminal  
• The EMBEDDED AUDIO signal...  
AC power input connector.  
Connect the provided AC power cord to an AC  
outlet.  
• Attach the provided power cord holder to prevent  
accidental disconnection of the AC power cord (☞  
“Attaching the power cord holder” on page 9).  
– is decoded into an analog signal, then emitted.  
– is emitted only when “SDI 1” or “SDI 2” is  
selected, and when EMBEDDED AUDIO  
signals come in to the E. AUDIO HD/SD SDI  
(IN 1 or IN 2) terminal.  
• Refer also to the user manual of each piece of  
equipment.  
6 E. AUDIO HD/SD SDI (IN 1, IN 2) terminals (BNC)  
Input terminals for the HD/SD SDI signals.  
• The terminals accept also EMBEDDED AUDIO  
signals including up to 12 audio channels with a  
sampling frequency of 48 kHz.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Computer signals (preset)  
DVI-D (HDCP) terminals  
7 Available signals  
The following signals are available for this monitor.  
Resolution  
Horizontal  
Frequency  
: Acceptable  
—: Not acceptable  
No.  
Signal name  
VGA60  
Scan system  
Vertical  
480  
Horizontal (kHz)  
Vertical (Hz)  
59.9  
Video signals  
1
2
3
4
5
6
7
8
9
640  
852  
31.5  
31.5  
37.9  
48.4  
47.8  
55.9  
64.0  
65.2  
75.0  
74.0  
45.0  
67.5  
37.5  
56.25  
Non-interlace  
Non-interlace  
Non-interlace  
Non-interlace  
Non-interlace  
Non-interlace  
Non-interlace  
Non-interlace  
Non-interlace  
Non-interlace  
Non-interlace  
Non-interlace  
Non-interlace  
Non-interlace  
Input terminal  
E. AUDIO HD/  
Signal format  
shown in the  
status display  
WVGA60  
480  
59.9  
COMPO.  
(Analog  
DVI-D (HDCP)  
(Digital component/  
digital RGB)  
No.  
Signal name  
SVGA60  
800  
600  
60.3  
VIDEO  
SD SDI  
component)*1  
(IN 1, IN 2)*2  
XGA60  
1024  
1280  
1440  
1280  
1680  
1600  
1920  
1280  
1920  
1280  
1920  
768  
60.0  
(page 7)  
1
2
3
4
5
6
7
8
9
NTSC  
NTSC  
WXGA (1280)  
WXGA+60  
SXGA60*4  
WSXGA+60*4  
UXGA60*4  
768  
60.0  
PAL  
PAL  
900  
60.0  
B/W50  
B/W50  
1024  
1050  
1200  
1200  
720  
60.0  
B/W60  
B/W60  
60.0  
480/60i  
480/59.94i  
576/50i  
480/60p  
480/59.94p  
480/60i  
60.0  
10 WUXGA60*4  
60.0  
480/59.94i  
576/50i  
11 720/60p  
12 1080/60p*4  
13 720/50p  
60.0  
480/60p  
480/59.94p  
576/50p  
640*480/60p  
1080  
720  
60.0  
50.0  
14 1080/50p*4  
1080  
50.0  
10 576/50p  
11 640*480/60p  
*4 When No. 7–10, 12 and 14 signals come in, thin lines will become obscured because their signal resolution is higher  
than the screen resolution.  
12 640*480/59.94p 640*480/59.94p  
13 720/60p  
720/60p  
• Non-preset signals may not be displayed normally even if their frequency is within the acceptable range (☞  
“Horizontal/vertical frequency (computer signal)” on page 21).  
• When a preset signal comes in, the signal format is shown on the status display. For other signals, the  
resolution is shown.  
14 720/59.94p  
15 720/50p  
720/59.94p  
720/50p  
16 720/30p  
720/30p  
17 720/29.97p  
18 720/25p  
720/29.97p  
720/25p  
Specification of the DVI-D (HDCP) terminal  
19 720/24p  
720/24p  
Connect it to the DVI-D output terminal on a personal computer.  
20 720/23.98p  
21 1080/60i  
720/23.98p  
1080/60i  
Pin No.  
Input signal  
T.M.D.S Data 2–  
T.M.D.S Data 2+  
T.M.D.S Data 2 shield  
NC  
Pin No.  
9
Input signal  
T.M.D.S Data 1–  
T.M.D.S Data 1+  
T.M.D.S Data 1 shield  
NC  
Pin No.  
17  
Input signal  
T.M.D.S Data 0–  
T.M.D.S Data 0+  
T.M.D.S Data 0 shield  
NC  
1
2
3
4
5
6
7
8
22 1080/59.94i  
23 1035/60i  
1080/59.94i  
1035/60i  
10  
18  
*3  
*3  
*3  
*3  
11  
19  
24 1035/59.94i  
25 1080/50i  
1035/59.94i  
1080/50i  
12  
20  
NC  
13  
NC  
21  
NC  
26 1080/60p  
27 1080/59.94p  
28 1080/50p  
29 1080/30p  
30 1080/29.97p  
31 1080/25p  
32 1080/24p  
33 1080/23.98p  
34 1080/30psF  
35 1080/29.97psF  
36 1080/24psF  
37 1080/23.98psF  
1080/60p  
1080/59.94p  
1080/50p  
1080/30p  
1080/29.97p  
1080/25p  
1080/24p  
1080/23.98p  
1080/60i  
DDC Clock  
DDC Data  
14  
+5 V Power  
GND  
22  
T.M.D.S Clock shield  
T.M.D.S Clock+  
T.M.D.S Clock–  
15  
23  
NC  
16  
Hot Plug Detect  
24  
CAUTION  
• Use only the provided screws.  
• Make sure the plug will not be pulled out  
after the cover is attached to the case.  
Attaching the power cord holder  
The provided power cord holder prevents accidental  
disconnection of the AC power cord from the AC IN terminal.  
• The power cord holder consists of two parts, a case and a  
cover.  
*3  
*3  
*3  
*3  
To detach the cover  
1080/59.94i  
1080/24psf  
1080/23.98psf  
1
2
3
AC IN  
Cover  
terminal  
Case  
*1 Analog component signals are compatible with Y on sync signals.  
*2 Compatible with EMBEDDED AUDIO signals  
*3 The signal is recognized as 1080/60i, 1080/59.94i.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
10  
Menu Configuration—MAIN MENU  
For the operation procedure, see page 7.  
PICTURE FUNCTION  
Setting for the picture quality  
Item  
To do  
Setting value  
APERTURE  
Select the frequency of the luminance signal compensated in  
“APERTURE LEVEL.”  
OFF, LOW, HIGH  
FREQ.*1  
APERTURE  
Compensate the frequency response of the luminance signal of the  
video signal.  
01 – 10  
LEVEL*1  
CTI  
LTI  
I/P MODE  
Adjust the clearness of the outlines of the chrominance signal.  
Adjust the clearness of the outlines of the luminance signal.  
Selects a proper mode corresponding to the input picture.  
OFF, NORMAL, HARD  
OFF, NORMAL, HARD  
NORMAL, CINEMA,  
FIELD  
sub menu  
Display the sub menu which enables you to adjust the items of “PICTURE FUNCTION” while  
viewing the actual picture.  
reset  
Restore the default settings for all the items in “PICTURE FUNCTION.”  
*1 Memorized for each input.  
Operation guide  
Shows the buttons for each operation.  
Setting value: –20 – +20  
BACK LIGHT  
Adjusts the brightness of the display.  
Setting value: AUTO, MODE1, MODE2, MODE3  
DVI INPUT SEL.  
When “AUTO” is selected, the format of signals come in to the DVI-D (HDCP) terminal is automatically  
recognized. (Normally, select “AUTO.”)  
• Select “MODE1”, “MODE2” or “MODE3” when the picture is not displayed correctly with “AUTO.”  
• DVI-D input of the monitor is compatible with HDCP.  
• The menu automatically disappears in about 30 seconds after the previous operation.  
• Some items may not appear on the menu depending on the input or the input signal.  
• The items controlled by the MAKE system do not appear on the menu.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MARKER*1*2  
Settings for marker functions  
1/2  
Item  
To do  
Setting value  
“NOTE”  
AREA MARKER*3  
Activate/deactivate the area marker and select the  
style of it.  
Select the aspect ratio of the area marker.  
MARKER ASPECT*3  
4:3, 14:9, 13:9, 2.35:1, 1.85:1,  
1.66:1  
SAFETY MARKER  
Activate/deactivate the safety marker and select the  
style of it.  
“NOTE”  
SAFETY AREA  
FRAME  
Adjust the area of the safety marker.  
Displays/hides the frame indicating the area of the  
specified aspect ratio.  
80% – 100%  
OFF, ON  
Operation guide  
Shows the buttons for each operation.  
CENTER MARKER  
LINE BRIGHTNESS  
Displays/hides the marker indicating the center  
position of the picture.  
Adjust the brightness of the marker.  
OFF, ON  
HIGH, LOW  
2/2  
Item  
• The menu automatically disappears in about 30 seconds after the previous operation.  
• Some items may not appear on the menu depending on the input or the input signal.  
• The items controlled by the MAKE system do not appear on the menu.  
To do  
Setting value  
R-AREA MARKER*3  
Activate/deactivate the area marker and select the  
style of it.  
Select the aspect ratio of the area marker.  
“NOTE”  
R-MARKER ASPECT*3  
R-SAFETY MARKER  
R-SAFETY AREA  
4:3, 14:9, 13:9, 2.35:1, 1.85:1,  
1.66:1  
“NOTE”  
Activate/deactivate the safety marker and select the  
style of it.  
Adjust the area of the safety marker.  
80% – 100%  
• The area marker or the safety marker is displayed by using AREA MARKER or SAFETY MARKER button, or  
external control.  
• Select either non-“R-” items or “R-” items to activate by using external control (“External Control” on page  
16).  
• When a picture is displayed in 4:3 aspect ratio, the safety marker for the 4:3 area is displayed.  
To display the safety marker for the area of a picture displayed in 16:9 aspect ratio, hide the area marker.  
(“NOTE”)  
*1 Memorized for each input.  
*2 Not displayed when picture is displayed in the 1:1 mode.  
*3 Displayed only when picture is displayed in 16:9 aspect ratio.  
NOTE  
Setting of “AREA MARKER”, “SAFETY MARKER”, “R-AREA MARKER”,  
“R-SAFETY MARKER”  
The setting values and features are as follows.  
OFF:  
Deactivate the marker.  
LINE:  
HALF:  
Displays the area with an outline.  
The area outside the specified aspect ratio of the screen is displayed at 50% transparency.  
HALF+L: The area of the specified aspect ratio of the screen is indicated by an outline, and the area  
outside of that is displayed at 50% transparency.  
BLK.:  
The area outside the specified aspect ratio of the screen is black. Only the portion of the picture  
within the designated area is displayed.  
BLK. +L: The area of the specified aspect ratio of the screen is indicated by an outline, and the area  
outside of that becomes black so that only the area inside the line is displayed.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12  
Menu Configuration—MAIN MENU (cont.)  
AUDIO SETTING  
Settings for the audio output balance, EMBEDDED AUDIO signals and level meter  
Item  
To do  
Setting value  
BALANCE  
Adjust the balance between the right and left  
speakers.  
Select the audio channel group of the  
EMBEDDED AUDIO signals.  
Adjust the level meter display for the  
EMBEDDED AUDIO signals.  
L5 – L1, 0, R1 – R5  
E.AUDIO GROUP*1  
“NOTE”  
“NOTE”  
LEVEL METER  
SETTING*1  
LEVEL METER ch Select how the audio channels are displayed on OFF, LINE (Displays the channels 1 – 6  
the level meter.  
at the left of the screen and 7 – 12 at the  
right.), DIVIDE (Displays the odd channels at  
the left of the screen and the even channels  
at the right.)  
Adjustment bar  
Displayed when selecting  
“BALANCE.”  
BAR TYPE  
Select the color of the level meter display.  
3COLORS (3 colors to indicate variations in  
input levels), W.100 (white)  
Operation guide  
Shows the buttons for each  
operation.  
REFERENCE  
LEVEL  
Select the standard input level indicated on the  
level meter.  
–20dB, –18dB  
OVER LEVEL  
Select the input level’s lower limit indicated in  
red for the “3COLORS” display.  
–10dB, –8dB, –6dB, –4dB, –2dB  
LOW, HIGH  
• The menu automatically disappears in about 30 seconds after the previous operation.  
• Some items may not appear on the menu depending on the input or the input signal.  
• The items controlled by the MAKE system do not appear on the menu.  
BAR BRIGHTNESS Select the brightness of the level meter.  
*1 Memorized for each input.  
NOTE  
Settings of “E.AUDIO GROUP”  
The setting values and selectable audio channels of EMBEDDED AUDIO signals are as follows.  
1G:  
channel(s) 1/2/3/4/1+2/3+4/1 – 4 (1G)  
2G:  
channel(s) 5/6/7/8/5+6/7+8/5 – 8 (2G)  
1-2G:  
3G:  
channel(s) 1/2/3/4/5/6/7/8/1+2/3+4/5+6/7+8/1 – 4 (1G)/5 – 8 (2G)/1 – 8 (1G+2G)  
channel(s) 9/10/11/12/9+10/11+12/9 – 12 (3G)  
1-3G:  
channel(s) 1/2/3/4/5/6/7/8/9/10/11/12/1+2/3+4/5+6/7+8/9+10/11+12/1 – 4 (1G)/5 – 8 (2G)/  
9 – 12 (3G)/1 – 8 (1G+2G)/1 – 12 (1-3G)  
Example of the level meter display—Level meter position and audio channels  
Ex.: When “LEVEL METER ch” is set to “LINE” and “BAR TYPE” is set to “3COLORS”  
OVER LEVEL  
REFERENCE LEVEL  
Red  
Yellow  
Green  
• When “BAR TYPE” is set to “W.100,the standard input level set in “REFERENCE LEVELis displayed with  
the line indication. The input level set in “OVER LEVELis not displayed.  
• The level meter with no audio signal input is displayed in white for “3COLORS,and in gray for “W.100.”  
You can select the position of the level meter display—top or bottom of the screen (“POSITION” in  
“INFORMATION” on page 15).  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WAVE FORM SETTING*1  
Settings for the wave form monitor  
Item  
To do  
Setting value  
POSITION  
Select the position of the wave form monitor.  
1 (lower right), 2 (lower left), 3 (upper left),  
4 (upper right)  
FILTER  
Activates/deactivates the low-pass filter for the  
incoming wave form data.  
FLAT (no filter), LOWPASS  
GAIN  
Adjust the gain level for the incoming wave form  
data.  
–10 – +10  
OVER LEVEL  
MARKING  
Select the over level for the incoming luminance  
signals.  
Activates/deactivates the function to change the  
color of a wave form when the signal exceeds the  
limit specified on “LEVEL(below).  
“NOTE”  
OFF, ON  
Operation guide  
Shows the buttons for each  
operation.  
LEVEL  
AUTO OFF  
Adjust the lower limit for the luminance signal  
070 –109  
ON, OFF  
Activates/deactivates the function to make the  
wave form monitor indication go off automatically  
15 minutes after displaying it.  
*1 This function does not work for the signals as follows:  
RGB input signals (digital), DVI signals (digital/inputted from personal computer), 1080/60p (analog/digital), 1080/50p  
(analog/digital), 640 *480/60p (analog/digital).  
SYNC FUNCTION  
Settings for the synchronization with signals  
Item  
To do  
Setting value  
NO SYNC ACTION  
Select the screen status when no signal is  
coming in.  
OFF,  
P.SAVE (power save mode),  
GRAY B. (gray screen)  
DELAY TIME  
Select the period until the screen status  
changes as selected in “NO SYNC ACTION”  
after signals stop coming in.  
30sec., 5min., 15min.  
LOW LATENCY  
Activates/deactivates the function to shorten  
the time taken to display the picture (low latency  
function).  
ON, OFF  
• If the picture is not displayed steadily while  
“ON” is selected, select “OFF.”  
• While “ON” is selected, the displayed picture  
may become unstable when an operation  
using buttons on the front panel or the menu  
is performed, or when the signal format  
changes.  
NOTE  
Example of the wave form monitor  
Ex.: When “MARKING” is set to “ON” and “LEVELis set to “080”  
• When setting “NO SYNC ACTION” to “GRAY B.,” the screen color changes to gray and the power consumption  
of the back light is saved by half.  
Selecting “P.SAVE” (power save mode) saves more power consumption by turning off the back light.  
White  
Red  
• The wave which goes over the value set on “LEVEL”  
is indicated in Red.  
CLOSED CAPTION*2 Setting value: OFF, CC1, CC2  
Selects the type of closed caption for analog composite signals (NTSC and B/W60 only).  
• Regardless of the setting, the closed caption is not displayed when the wave form monitor is displayed.  
*2 Memorized for each input (VIDEO1 and VIDEO2).  
Video signal  
Start  
End  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
14  
Menu Configuration—SET-UP MENU  
FUNCTION SETTING  
For the operation procedure, see page 7.  
Setting for the sub menu display, color system, color of the tally lamp and the picture size.  
Item  
To do  
Setting value  
“NOTE”  
sub menu POSI. Select the contents and displaying position of “sub menu.”  
COLOR  
SYSTEM  
Select the color system.  
• If the picture is unstable with “AUTO,select “PALor “NTSC.”  
AUTO, NTSC, PAL  
TALLY SELECT Select the color of the tally lamp.  
GREEN, RED  
SD4:3 LARGE  
Change the picture size of 4:3 format signal.  
“NOTE”  
PICTURE SUB ADJ.  
Adjusts the standard level for the picture adjustment and selects the set-up level for the input video signal.  
Item  
To do  
Setting value  
CONTRAST*1 Adjust the standard level for the contrast adjusted –20 – +20  
with CONTRAST knob on the front panel.  
Adjust the standard level for the brightness  
adjusted with BRIGHT knob on the front panel.  
Adjust the standard level for the chroma adjusted –20 – +20  
with CHROMA knob on the front panel.  
Adjust the standard level for the phase adjusted  
with PHASE knob on the front panel.  
BRIGHT*1  
CHROMA*1  
PHASE*1  
–20 – +20  
Operation guide  
Shows the buttons for each  
operation.  
–20 – +20  
NTSC SETUP Select the set-up level of the input NTSC signal. 00 (compliant with 0% set-up signal), 7.5 (compliant  
with 7.5% set-up signal)  
COMPO.  
LEVEL  
Select the level of the analog component signal  
(480i and 576i only).  
B75 (compliant with BetacamVTR 7.5% set-up  
signal), B00 (compliant with BetacamVTR 0% set-  
up signal), SMPTE (compliant with M2VTR signals)  
• The menu automatically  
disappears in about 30  
seconds after the previous  
operation.  
• Some items may not appear  
on the menu depending on  
the input or the input signal.  
• The items controlled by  
the MAKE system do not  
appear on the menu.  
sub menu  
reset  
*1 Memorized for each input.  
Display the sub menu which enables you to adjust the items in “PICTURE SUB ADJ.while viewing the  
actual picture.  
Restore the default settings for all the items in “PICTURE SUB ADJ.”  
SIZE/POSI. ADJ.  
Adjusts the size and position of the picture.  
Item  
H SIZE*2  
To do  
Setting value  
Adjust the horizontal picture size.  
H POSITION*2 Adjust the horizontal picture position.  
Setting value varies depending on  
the signals.  
NOTE  
V SIZE*2  
V POSITION*2 Adjust the vertical picture position.  
Adjust the vertical picture size.  
Settings of “sub menu POSI.”  
The setting values and features are as follows.  
LOWER1: Displays the current setting and adjustment bar at the  
lower part of the screen.  
UPPER1: Displays the current setting and adjustment bar at the  
upper part of the screen.  
sub menu  
Display the sub menu which enables you to adjust the items of “SIZE/POSI. ADJ.while viewing the  
actual picture.  
Restore the default settings for all the items in “SIZE/POSI. ADJ.”  
reset  
*2 Memorized for each signal format.  
WHITE BALANCE SET.  
LOWER2: Displays the current setting at the lower part of the  
screen.  
Selects the color temperature and adjusts the drive level and cutoff point of each color (R/G/B).  
Item  
To do  
Setting value  
UPPER2: Displays the current setting at the upper part of the  
screen.  
COLOR TEMP.  
Select the color temperature.  
9300K, 6500K, USER  
MIN – 000 – MAX (in 256 grades)  
R DRIVE, G DRIVE, Adjust the drive level of each color (red, green, and blue).  
B DRIVE*3  
• The adjustment bar is not displayed for some items.  
R CUT OFF, G CUT  
OFF, B CUT OFF*3  
sub menu  
Adjust the cutoff point of each color (red, green, and blue).  
MIN – 000 – MAX (in 256 grades)  
Settings of “SD4:3 LARGE”  
The setting values and features are as follows.  
Display the sub menu which enables you to adjust the items in “WHITE BALANCE SET.” while  
viewing the actual picture.  
Restore the default settings for the drive levels and cutoff points of the selected color  
temperature.  
OFF:  
Fit the vertical picture size into the pixel numbers of  
the monitor display.  
reset  
ON:  
Fit the vertical picture size into that of the monitor  
display.  
*3 Memorized for each color temperature.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
(“External Control” on pages 16 to 18)  
REMOTE SETTING  
Settings for the external control  
Item  
To do  
Setting value  
SERIAL TYPE  
Select the input terminal used for external control by  
serial communication.  
RS232C, RS485  
PARALLEL TYPE  
Select the external control method for the MAKE/  
TRIGGER terminal.  
MAKE, TRIGGER, SET  
PIN1, PIN2, PIN3,  
PIN4, PIN5  
Assign the control functions to the pins of the MAKE/  
TRIGGER terminal.  
• Assign a function to each pin terminal by selecting  
“SET” in “PARALLEL TYPE” mentioned above. (The  
functions are assigned for “PIN6” – “PIN8” and you  
cannot change the assignment of these functions.)  
“Functions controlled by the MAKE/  
TRIGGER system” on page 17  
Operation guide  
Shows the buttons for each  
operation.  
INFORMATION  
Settings for the information display of the monitor  
Item  
To do  
Setting value  
POSITION  
UPPER, LOWER  
Select the position to show the information display (“On the  
Information Display” on page 7).  
SOURCE ID  
Select if the name assigned in “CHARACTER SET.” is displayed on  
the screen (“On the Information Display” on page 7).  
OFF, ON  
CHARACTER SET.*1 Assign a name to each video source as you like (10 characters at  
“NOTE”  
maximum).You can also enter a name using the RS-232C system.  
STATUS DISPLAY  
CRC ERROR  
Select if the status of the current input and the setting of muting are  
displayed on the screen (“On the Status Display” on page 7).  
Select if the CRC error indication for the input HD SDI signal is displayed ON, OFF  
on the screen (“On the Information Display” on page 7).  
AUTO, OFF, ON  
SUB HOUR METER Display the hours of use (unit: hour).You can reset this item.  
MODEL  
VERSION  
HOUR METER  
Display the model name of the monitor.  
Display the version of the monitor.  
Display the total hours of use (unit: hour). This item is used for maintenance of the monitor.You  
cannot reset this item.  
• The menu automatically disappears in about 30 seconds after the previous operation.  
• Some items may not appear on the menu depending on the input or the input signal.  
• The items controlled by the MAKE system do not appear on the menu.  
*1 Memorized for each input.  
CONTROL LOCK  
Setting value: OFF, ON  
Turns on (or off) the control lock function to disable the buttons on the front panel.  
• The following operations are available even when this function is activated.  
Turning on/off (on standby) the monitor  
– Displaying the SET-UP MENU (by pressing button while holding button) and turning “CONTROL LOCK”  
to “OFF”  
– Operating the monitor by an external control  
NOTE  
If you try other operations, “ Control lock on!” appears on the screen.  
Setting of “CHARACTER SET.”  
Assign a name for each video source.  
all reset  
1 Change the input to one that you want to assign a video source name for.  
2 Select “CHARACTER SET.”  
Restores all the settings and adjustments of the monitor to the default.  
• “HOUR METER” and the settings done by using the adjustment knobs on the front panel will not be reset.  
• When you operate the monitor with the AC power supply, the monitor is turned off (on standby) then turned  
on automatically. When you operate the monitor with the DC 12 V power supply, the monitor is turned off (on  
standby).  
3 Press  
buttons to select the first character.  
• Each time you press button, the character changes as follows. Press button to reverse the order.  
Space  
4 Press button to move the arrow to the next space.  
• The characters entered before moving the arrow are memorized.  
5 Repeat steps 3 and 4 (10 characters at maximum).  
6 Press MENU button to store the name.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
16  
External Control  
Control priority is as follows.  
MAKE > TRIGGER = serial communication = buttons and menu on the monitor  
7 About the external control  
This monitor has three external control terminals.  
You can use the external control even when “CONTROL LOCK” is set to “ON” (page 15).  
MAKE/TRIGGER terminal (RJ-45): The following external control systems are available.  
(1) MAKE (make contact) system: Controls the monitor by short-circuiting the corresponding pin terminal to  
the GND pin terminal, or disconnecting (opening) it.  
• When the monitor is off (on standby), external control is not available. But certain external controls (starting/  
terminating communication, turning on the monitor) are available through the serial communication (page 18).  
(2) TRIGGER (trigger) system: Controls the monitor by sending the pulse signal instantaneously to the  
corresponding pin terminal.  
<MAKE/TRIGGER system>  
You can control the monitor by a personal computer or dedicated controller*2.  
• For the details, see page 17.  
“Using the MAKE/TRIGGER system” on page 17  
*2 The controller is not commercially available. Consult your dealer if you need it.  
RS-485 terminals (RJ-45): Controls the monitor with the RS-485 system. (“Using the serial communication”  
on page 18)  
<Serial communication>  
RS-232C terminal (D-sub 9-pin): Controls the monitor with the RS-232C system. (“Using the serial  
communication” on page 18)  
Set the following items of “REMOTE SETTING” in SET-UP MENU according to the external control terminal and  
control system (“SERIAL TYPE”, “PARALLEL TYPE” on page 15).  
PC, etc.  
The settings of this unit  
Control terminal  
Control system  
“SERIAL TYPE” setting  
PARALLELTYPE” setting  
RS-485 RS-485  
OUT IN  
RS-485  
OUT  
RS-485  
IN  
RS-485  
OUT  
RS-485 IN  
or  
RS-232C  
MAKE/TRIGGER  
terminal  
MAKE  
MAKE  
TRIGGER  
TRIGGER  
RS-485 terminal  
RS-232C terminal  
Serial  
communication  
RS-485  
RS-232C  
RS485*1  
RS232C*1  
• For the details, see page 18.  
*1 For a monitor connected to a personal computer etc, select the terminal the equipment is actually connected to. For  
other monitors, select “RS485.”  
Download from Www.Somanuals.com. All Manuals Search And Download.  
<Functions controlled by the MAKE/TRIGGER system>  
7 Using the MAKE/TRIGGER system  
Display  
TALLY SEL  
Functions to be controlled  
Selects the color of the tally lamp.  
Changes the input to “SDI 1.”  
Changes the input to “SDI 2.”  
Changes the input to “DVI.”  
Changes the input to “COMPO.”  
Changes the input to “VIDEO.”  
The area marker indication  
The safety marker indication  
Indication of the area of the specified aspect ratio  
The center marker indication  
Selects the items of “MARKER”*3  
Changes the aspect ratio.  
Displays in 1:1 mode.  
Opening  
Green  
Invalid  
Invalid  
Invalid  
Invalid  
Invalid  
Off  
Short-circuiting  
The MAKE/TRIGGER terminal is configured as follows.You can assign a function to each pin terminal in  
“REMOTE SETTING” (“PIN1, PIN2, PIN3, PIN4, PIN5” in “PARALLEL TYPE” on page 15).  
You cannot change the functions assigned to the pin terminals from 6th to 8th.  
Red  
Valid  
Valid  
Valid  
Valid  
Valid  
On  
SDI 1  
SDI 2  
DVI  
Pin No.  
Pin name  
COMPONENT  
VIDEO  
1
2
3
4
5
6
7
8
PIN1  
PIN2  
PIN3  
PIN4  
PIN5  
PIN6 (TALLY)*1  
PIN7 (ENABLE)*2  
PIN8 (GND)  
A.MARKER  
S.MARKER  
FRAME  
Off  
On  
Off  
On  
This is a female terminal.  
C.MARKER  
MARK.SEL  
ASPECT  
1:1  
Off  
On  
Non-“R-” items  
4:3  
“R-” items  
16:9  
On  
Off  
STATUS  
Status display*4  
“On the Status Display” on page 7  
5
L.METER  
TIME CODE  
SOURCE ID  
WAVE FORM  
C.C.  
Audio level meter display  
Time code display  
*
*1 The 6th pin terminal controls turning on or off the tally lamp (available to control even when the 7th pin terminal is  
invalid).  
*2 The 7th pin terminal makes the external control valid/invalid. Make sure to control the terminal by the MAKE system.  
Off  
Off  
Off  
On  
On  
On*6  
“SOURCE ID” in “INFORMATION” on page 15  
Wave form monitor display  
Closed caption display  
7
*
COLOR OFF  
SCR CHECK  
I/P MODE  
MUTING  
– – –  
Color off  
Color  
Monochrome  
To assign the functions to the pin terminals  
8
9
Screens check  
*
*
For the operation procedure, see page 7.  
Change a mode according to a input picture.  
Muting on/off  
1 Select “REMOTE SETTING” on the SET-UP MENU.  
Off  
On  
2 Set “PARALLEL TYPE” to “SET.”  
3 Select a pin name (“PIN1” – “PIN5”) for which you want to assign a function, then select the function you want  
to assign.  
No function  
*3 Selects which functions in “MARKER” are activated, non-“R-” items or “R-” items (“MARKER” on page 11).  
*4 Displays the information shown when INPUT SELECT button of the current input is pressed (“On the Status Display”  
on page 7). While controlling with the MAKE system, the information is displayed only at the moment of short-circuiting.  
*5 While controlling with the MAKE system, the level meter is switched between displayed (short-circuiting) and hidden  
(opening). When “LEVEL METER ch” is set to “OFF,” the level meter is not displayed (“NO EFFECT” appears). While  
controlling with the TRIGGER system, the pattern of the audio channel display is switched.  
*6 While controlling with the MAKE system, the wave form monitor will not disappear until opening the terminal  
(regardless of the “AUTO OFF” setting on page 13).  
• For selectable functions, see the tables on the right.  
Operation of the external control  
1 Set “PARALLEL TYPE” of “REMOTE SETTING” to “MAKE” or “TRIGGER” in the SET-UP MENU.  
2 Short-circuit the 7th pin terminal (ENABLE) to the 8th pin terminal (GND) so that the monitor can be controlled  
by the external control.  
3 When the “MAKE” system is selected: Operate each function by short-circuiting the corresponding pin terminal  
*7 For analog composite signals (NTSC and B/W60 only). While controlling with the MAKE system, the closed caption  
is switched between displayed (short-circuiting) and hidden (opening). When “CLOSED CAPTION” is set to “OFF,” the  
closed caption is not displayed (“NO EFFECT” appears). While controlling with the TRIGGER system, the type of the  
closed caption can be selected.  
to the 8th pin terminal (GND) or opening it.  
When the “TRIGGER” system is selected: Operate each function by pulse control, that is short-circuiting the  
corresponding pin terminal to the 8th pin terminal (GND) for about 1 second and opening it.  
*8 While controlling with the MAKE system, the screen is switched between normal screen (opening) and blue screen  
(short-circuiting). While controlling with the TRIGGER system, the screen changes as same as when pressing  
SCREENS CHECK button (q on page 6).  
• When changing the input with MAKE system, only one pin terminal must be short-circuited. (Other pin terminals  
must be opened.)  
• When selecting the “TRIGGER” system, you can operate only one function at a time. Operate the functions one  
by one.  
*9 Must be controlled with the TRIGGER system. The mode changes in the order of “NORMAL”  
(This function cannot be controlled with the MAKE system.)  
\
“CINEMA”  
\
“FIELD”.  
You cannot assign the same function to different pin terminals.  
• The TRIGGER system switches each function by short-circuiting the pin terminal for about 1 second and  
opening it.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
18  
External Control (cont.)  
Example of communication procedures  
1Starting the communication:  
7 Using the serial communication  
You can control the monitor from a personal computer etc. via the RS-485 or RS-232C terminal.  
• Consult your dealer for the details of the external control specification.  
connection command (!00BCN1Cr)  
Monitor  
2Monitor’s status (@00BOKCr)  
<Communication specifications>  
Terminal  
Input terminal  
Cable  
Communication specifications  
3Selecting “SDI 1” input (!00BINACr)  
4Monitor’s status (@00BOKCr)  
specification  
RS-485  
A straight LAN cable  
PC, etc.  
Baud Rate: 4800 bps  
Data Bits: 8 bits  
Parity: No parity  
Stop Bits: 1 bit  
Flow Control: No control  
Communication Code: ASCII Code  
RS-232C  
A straight cable with a D-sub 9-pin  
connector (male for the monitor,  
female for the personal computer  
etc.)  
5Terminating the communication: termination command  
(!00BCN0Cr)  
See below  
6Monitor’s status (@00BOKCr)  
<Basic command list>  
No.  
Commands  
Functions  
Starts communication (connection)  
Data  
No data  
<Specifications of the RS-485 terminal>  
<Specifications of the RS-232C terminal>  
1
!
*
**1  
B
C
N
1
Cr  
Terminates communication  
(termination)  
x*2 Cr Assigns the control ID  
2
!
*
**1  
B
C
N
0
Cr  
No data  
This is a female terminal.  
This is a female terminal.  
3
4
!
!
*
*
**1  
**1  
B
B
I
I
D
D
S
R
E
E
T
T
x
Cr  
01 – 99  
No data  
Initializes the control ID  
00: Hide  
01: Display  
00: Hide  
01: Display  
5
6
7
!
!
!
*
*
*
**1  
**1  
**1  
B
B
B
I
I
D
D
E
D
C
N
S
H
U
P
K
x
x
x*2 Cr Displays/hides the ID  
Pin No.  
IN terminal signal OUT terminal signal  
Pin No.  
Signal  
NC  
1
2
3
4
5
6
7
8
TXD +  
TXD –  
RXD +  
NC  
TXD +  
TXD –  
RXD +  
NC  
1
2
3
4
5
6
7
8
9
Flashes/hides the selected ID No. of  
the monitor  
x*2 Cr  
RXD  
TXD  
NC  
Displays the MAIN MENU/Quits the  
menu operation  
M
Cr  
No data  
8
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
**1  
**1  
**1  
**1  
**1  
**1  
**1  
**1  
**1  
**1  
**1  
**1  
**1  
**1  
**1  
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
U
D
A
A
S
P
P
I
I
I
I
I
P
O
D
D
E
W
W
N
N
N
N
N
I
Cr  
W
J
J
T
No data  
No data  
No data  
No data  
No data  
No data  
No data  
No data  
No data  
No data  
No data  
No data  
No data  
Moves the cursor upward (  
)
NC  
NC  
GND  
NC  
9
N
R
L
Cr  
Cr  
Cr  
P
Moves the cursor downward (  
)
RXD –  
NC  
RXD –  
NC  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
Makes setting/adjustment (  
Makes setting/adjustment (  
Displays the SET-UP MENU  
Turns on the monitor  
Turns off the monitor (on standby)  
Selects “SDI 1” input  
Selects “SDI 2” input  
Selects “DVI” input  
Selects “COMPO.input  
Selects “VIDEO” input  
Displays the status*3  
)
)
RTS  
CTS  
NC  
GND  
GND  
U
Cr  
1
0
Cr  
Cr  
Cr  
Cr  
Cr  
Cr  
Cr  
P
• The 7th terminal and the 8th terminal are connected.  
A
B
C
D
E
S
U
P
<Command outline>  
All commands consist of the following segments.  
Header  
Monitor ID  
Command ID  
Function  
Data  
Cr (0DH)  
D
A
A
Cr  
E
x*2 Cr  
On Header  
M
S
T
x
x
x*2 Cr Turns muting on/off  
00: Off, 01: On  
00: 4:3, 01: 16:9  
“!”: Operation commands from the personal computer, etc. For details, see <Basic command list> on the right.  
“?”: Reference commands from the personal computer, etc.  
Changes the aspect ratio  
“@”: Status returns from the monitor  
• “Cr” is 0Dh.  
To start communication, send the connection command from the personal computer etc.  
To terminate the communication, send the termination command from the personal computer etc.  
• The commands for starting communication (connection) (No. 1), terminating communication (termination)  
(No. 2), and turning on the monitor (No. 13) can be used while the monitor is off (on standby).  
*1 Enter the monitor’s ID for “ **.” The initial setting of the monitor’s ID is “00.When connecting several monitors, “00” is a  
command for controlling all monitors at once.  
*2 Enter the appropriate data to “xx.”  
*3 Displays the information shown when the INPUT SELECT button currently lit is pressed (“On the Status Display” on  
page 7).  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
Solutions to common problems related to the monitor are described here. If none of the solutions presented here  
solve the problem, unplug the monitor and consult an authorized dealer or service center.  
Symptom  
Probable cause and corrective action  
Page  
Symptom  
Probable cause and corrective action  
Page  
6
8
8
8
• Adjust the picture contrast or brightness by using the adjustment  
knobs on the front panel. Or, adjust “CONTRAST” or “BRIGHT” of  
“PICTURE SUB ADJ.in the SET-UP MENU.  
6, 14  
• Press the  
button.  
The picture becomes  
blurred.  
Turn on the POWER switch or DC switch on the rear panel.  
• Firmly insert the AC power plug or DC 12 V power plug.  
• When using a DC 12 V power supply, charge the battery or replace it  
with a charged one.  
No power supply  
• Check whether the setting of 1:1 or ASPECT buttons is appropriate.  
• Check whether the input signal format is acceptable on the monitor.  
6
9
Wrong picture position, • Adjust the picture size (H SIZE/V SIZE) or position (H POSITION/V  
14  
• Select the correct input using the INPUT SELECT buttons.  
• Connect the signal cable firmly.  
Turn on the power of the connected component and set the output  
correctly.  
6
8
wrong picture size.  
POSITION) of “SIZE/POSI. ADJ.in the SET-UP MENU.  
• For some signals, the picture cannot be displayed fully in the effective  
screen area. There is no sure method to solve this problem.  
No picture with the  
power on  
• Check whether the input signal format is acceptable on the monitor.  
9
• The items which are not available for the current input or the current  
input signal are not displayed on the menu. Change the input or the  
input signal.  
• The items controlled by the MAKE system do not appear on the  
menu.  
• Adjust the volume level.  
6
6
8
Some items do not  
appear on the menu.  
• Deactivate the muting function.  
• Connect the signal cable firmly.  
Turn on the power of the connected component and set the output  
correctly.  
17  
No sound  
• Set “CONTROL LOCK” in the SET-UP MENU to “OFF.”  
You cannot use the buttons for the items controlled by the MAKE  
system. Disable the external control.  
15  
16,17  
Buttons on the monitor  
do not work.  
“OTHERS” or “Out of  
range” appears.  
• Check whether the input signal format is acceptable on the monitor.  
7, 9  
• Select the correct input using the INPUT SELECT buttons.  
• Connect the signal cable firmly.  
6
8
Turn on the power of the connected component and output video  
signals. Or, check whether the video output of the component (video  
output setting of the VCR or graphic board of the computer) is set  
correctly.  
“NO SYNC” appears.  
• Adjust each picture adjustment knob on the front panel or adjust the  
items of “PICTURE SUB ADJ.in the SET-UP MENU. Or, perform  
“reset” in “PICTURE SUB ADJ.”  
6, 14  
• Check whether the setting of COLOR OFF or SCREENS CHECK  
buttons are appropriate.  
6
Wrong color, no color  
• Select the proper color system (“COLOR SYSTEM”) in “FUNCTION  
SETTING” of the SET-UP MENU.  
• Adjust the items of “WHITE BALANCE SET.” in the SET-UP MENU.  
Or, perform “reset” in “WHITE BALANCE SET.”  
14  
14  
The following are not malfunctions.  
• When a still image is displayed for a long time, it may remain indistinctly on the screen after the picture has  
changed. Though the remaining picture will disappear after a while, there may be a case that it remains  
for a long period depending on the length of time the still image was displayed for. This is due to the  
characteristics of the LCD display and is not a malfunction.  
• Red spots, blue spots and green spots on the panel surface are a normal characteristic of LCD displays,  
and not a problem. The LCD display is built with very high precision technology; however, be aware that a  
few pixels may be missing or constantly lit.  
• The following symptoms are problems only when pictures or sounds are not played back normally.  
– A slight electric shock occurs when you touch the monitor.  
– The top and/or rear panel of the monitor becomes hot.  
– The monitor emits a cracking noise.  
– The monitor emits a mechanical noise.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
20  
Troubleshooting (cont.)  
Maintenance  
Unplug this product from the wall outlet before cleaning.  
7 Self-check program  
This monitor has a self-check function, which allows it to detect malfunctions and alert you. This makes  
troubleshooting easier. Whenever a problem occurs, one or some of the INPUT SELECT lamps will flash. If this  
happens, follow the steps below and contact your dealer to resolve the problem.  
Screen  
To avoid irreparable change in appearance of the screen such as uneven color, discoloration, scratches, be  
careful about the following:  
• Do not paste or stick anything using any glues or adhesive tapes.  
• Do not write anything on the screen.  
• Do not strike the screen with a hard object.  
• Avoid condensation on the screen.  
• Do not wipe the screen with solvent such as alcohol, thinner, or benzine.  
• Do not wipe the screen forcefully.  
Wipe stains off the screen with a soft cloth. If the screen gets heavily stained, wipe it with a soft cloth soaked in  
water-diluted neutral detergent and wrung well, then wipe with a soft dry cloth.  
Cabinet  
To avoid the deterioration or damages of the cabinet such as its paint’s peeling away, be careful about the  
following:  
• Do not wipe the cabinet using solvent such as alcohol, thinner, or benzine.  
• Do not expose the cabinet to any volatile substance such as insecticides.  
• Do not allow any rubber or plastic in contact for a long time.  
• Do not wipe the cabinet forcefully.  
Wipe stains off the cabinet with a soft cloth. If the cabinet gets heavily stained, wipe it with a soft cloth soaked in  
water-diluted neutral detergent and wrung well, then wipe with a soft dry cloth.  
When the screen goes blank, and one or some of the INPUT SELECT lamps (DVI, COMPO., VIDEO) on the  
front control panel start flashing...  
Ventilation openings  
Use a vacuum cleaner to get rid of the dust around the intakes (all the openings). If a vacuum cleaner is not  
available, use a cloth and wipe it off. Leaving the dust around the intakes may prevent proper temperature control  
and cause damage to the product.  
1 Check which lamps are flashing.  
2 Press  
button to turn off (on standby) the monitor.  
3 Turn off the POWER switch and DC switch on the rear panel.  
4
When the AC power supply is used: Disconnect the AC power cord from the AC outlet.  
When a DC 12 V power supply is used: Detach the battery or disconnect the plug  
from the DC IN 12V terminal.  
5 Contact your dealer with the information about which lamps were flashing.  
• If you turn on the monitor soon after turning it off (or after a short-term power failure), the INPUT SELECT  
lamps may flash and no image may be displayed.  
When this happens, turn off power and wait at least 10 seconds before turning on the monitor again.  
If the INPUT SELECT lamps do not flash, you can use the monitor as normal.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
7 General  
7 Input/output terminals  
Model name  
Type  
DT-V17L3DY  
VIDEO  
Input/output of composite signal:  
1 line, BNC connector x 2, 1 V(p-p), 75 Ω  
Multi format LCD monitor  
Type 17 wide format  
16:10  
* The input (IN) and output (OUT) terminals are bridge-connected (auto  
termination).  
Screen size  
Aspect ratio  
LCD panel  
DVI-D (HDCP)  
DVI-D signal input (compatible with HDCP):  
DVI-D connector x 1 (compatible with DDC2B)  
17˝ wide, active matrix TFT  
Effective screen size  
Width: 367.2 mm (14 7/16˝)  
Height: 229.5 mm (9˝)  
COMPO. (Y, PB/B-Y, PR/R-Y) Input/output of analog component signal:  
1 line, BNC connector x 6  
Number of pixels displayed  
Number of colors displayed  
Viewing angle (TYP.)  
1 440 x 900  
Y:  
1 V(p-p), 75 Ω  
0.7 V(p-p), 75 Ω  
PB/B-Y, PR/R-Y:  
16.77 million  
* The input (IN) and output (OUT) terminals are bridge-connected (auto  
termination).  
160° (Horizontally), 140° (Vertically)  
400 cd/m2  
Panel brightness (TYP.)  
Contrast ratio (TYP.)  
E. AUDIO HD/SD SDI (IN 1)  
E. AUDIO HD/SD SDI (IN 2)  
Digital signal input (compatible with EMBEDDED AUDIO signals):  
auto detection, 1 line, BNC connector x 1  
600:1  
Horizontal/vertical frequency  
(computer signal)  
H: 31.469 kHz – 75.000 kHz  
V: 48 Hz – 65 Hz  
E. AUDIO HD/SD SDI  
(SWITCHED OUT)  
Digital signal output (compatible with EMBEDDED AUDIO signals):  
1 line switched out, BNC connector x 1  
* Some signals within this frequency range may not be displayed (“Out of  
range” is displayed).  
AUDIO (IN)  
Analog audio signal input:  
1 line, RCA connector x 2,  
500 mV (rms), high impedance  
Compliant video signal format  
Format  
“Available signals” on page 9  
AUDIO (MONITOR OUT)  
Analog audio signal output: 1 line, RCA connector x 2,  
500 mV (rms)  
HD SDI: BTA S-004B, SMPTE292M  
SD SDI: ITU-R BT.656: 525/625  
SMPTE259M: 525  
REMOTE (MAKE/TRIGGER)  
REMOTE (RS-485)  
“Using the MAKE/TRIGGER system” on page 17  
EMBEDDED AUDIO: SMPTE299M, SMPTE272M  
“Using the serial communication” on page 18  
Audio output  
Internal speaker: 1.0 W + 1.0 W  
REMOTE (RS-232C)  
Operating conditions  
Operating temperature: 5°C – 35°C (41°F – 95°F)  
Operating humidity: 20% – 80% (non-condensing)  
(Slightly variable depending on ambient conditions for installation.)  
Power requirements  
Rated current  
AC 120 V, 50 Hz/60 Hz  
DC 12 – 17 V  
0.56 A (AC 120 V)  
3.0 A (DC 12 – 17 V)  
External dimensions  
(excluding protruding parts)  
Width:  
Height: 344.8 mm (13 5/8˝) (with the stand), 304 mm (12˝) (without the stand)  
Depth: 199 mm (7 7/8˝) (with the stand), 86 mm (3 1/2˝) (without the stand)  
395 mm (15 5/8˝) (with the stand), 395 mm (15 5/8˝) (without the stand)  
Weight  
7 kg (15.5 lbs) (with the stand)  
5.3 kg (11.7 lbs) (without the stand)  
Accessories  
AC power cord, Power cord holder x 1, Screw x 2 (for power cord holder),  
Ferrite core x 1 (for external battery)  
Use the Anton Bauer Dionic 90 (mount: QR DXC-M3A) external battery.  
• For easy understanding, pictures and illustrations are shown by being emphasized, omitted or composed,  
and may be slightly different from actual products.  
• Design and specifications are subject to change without notice.  
CAUTION  
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.  
• All company names and product names mentioned herein are used for identification purposes only, and  
may be the trademarks or registered trademarks of their respective companies.  
Notice on transportation  
This monitor is precision equipment and needs dedicated packing material for transportation.  
Never use any packing material supplied from sources other than JVC or JVC-authorized dealers.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
22  
Specifications (cont.)  
Unit: mm (inch)  
7 Dimensions  
<Front view>  
<Side view>  
<Rear view>  
86 (3 1/2 )  
40 (1 5/8)  
1.5 (1/16)  
VESA mounting holes  
(Size: 4-M4, depth: 10 mm)  
395 (15 5/8)  
100  
34 (1 3/8)  
240 (9 1/2)  
199 (7 7/8)  
* at the higher position  
** at the lower position  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DT-V17L3DY MULTI FORMAT LCD MONITOR  
© 2008 Victor Company of Japan, Limited  
1010TKH-MW-VP  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Insignia DVD Recorder NS 1DRVCR User Manual
Intellinet Network Solutions Network Router 524582 User Manual
Jenn Air Cooktop JED8430 User Manual
John Lewis Dishwasher JLDWW 1203 User Manual
JVC Computer Accessories AAT100BT User Manual
JVC Home Security System VN C10 User Manual
Karcher Vacuum Cleaner KMR 1550 D User Manual
Kenwood Car Video System DDX5034M User Manual
KiSS Networked Entertainment Car Video System DP 470 User Manual
KitchenAid Range W10154991A User Manual