Intellinet Network Solutions Network Router 524582 User Manual

Wireless G

4-Port VPN

router

quick

iNstall

Guide

Model 524582

INT-524582-QIG-0309-01

Download from Www.Somanuals.com. All Manuals Search And Download.

Thank you for purchasing the INTELLINET NETWORK SOLUTIONS^™

Wireless G 4-Port VPN Router, Model 524582.

This quick install guide presents the rudimentary steps required to set up

and operate this device. For more detailed instructions and speciﬁcations,

refer to the user manual 1) on the CD enclosed with this product; 2) on

the Web site listed below; or 3) in some cases, printed and enclosed

with this product. Contact your INTELLINET NETWORK SOLUTIONS

dealer with comments or questions, or visit www.intellinet-network.com

for information on the latest software and ﬁrmware updates, related

products and additional contact information.

NOTE: Some screen images have been modiﬁed to ﬁt the format of

this quick install guide.

reGulatory statemeNts

FCC Part 15

This equipment has been tested and found to comply with the limits for

a Class B digital device, pursuant to Part 15 of FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment to an outlet on a different circuit.

4. Consult the dealer or an experienced radio technician for help.

FCC Caution

This equipment must be installed and operated in accordance with the

provided instructions, and a minimum of 20 cm spacing must be provided

between a computer-mounted antenna and a person’s body (excluding

Download from Www.Somanuals.com. All Manuals Search And Download.

extremities of hands, wrists and feet) during wireless modes of operation.

This device complies with Part 15 of FCC Rules. Operation is subject

to the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation. Any changes

or modiﬁcations not expressly approved by the party responsible for

compliance could void the authority to operate equipment.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth

for an uncontrolled environment. To avoid the possibility of exceeding

the FCC radio frequency exposure limits, human proximity to the antenna

shall not be less than 20 cm (8 inches) during normal operation. The

antenna(s) used for this transmitter must not be co-located or operating

in conjunction with any other antenna or transmitter.

R&TTE Compliance Statement

This equipment complies with all the requirements of Directive 1999/5/

EC of the European Parliament and the Council of March 9, 1999, on

radio equipment and telecommunications terminal equipment and the

mutual recognition of their conformity (R&TTE). The R&TTE Directive

repeals and replaces Directive 98/13/EEC (Telecommunications Terminal

Equipment and Satellite Earth Station Equipment) as of April 8, 2000.

Safety

This equipment is designed with the utmost care for the safety of those

who install and use it. However, special attention must be paid to the

dangers of electric shock and static electricity when working with electrical

equipment. All FCC and computer manufacturer guidelines must therefore

be followed at all times to ensure the safe use of the equipment.

EU Countries Intended for Use

The ETSI version of this device is intended for home and ofﬁce use in

Austria, Belgium, Denmark, Finland, France, Germany, Greece, Ireland,

Italy, Luxembourg, the Netherlands, Portugal, Spain, Sweden and the

U.K. The ETSI version of this device is also authorized for use in EFTA

member states Iceland, Liechtenstein, Norway and Switzerland. (EU

countries not intended for use: none.)

Download from Www.Somanuals.com. All Manuals Search And Download.

iNitial setuP

1. Set up your network as shown in the diagram. NOTE: The four LAN

connections are examples only.

2. Your LAN PC clients need to be set so that an IP address can be

obtained automatically. By default, the router’s DHCP server is enabled

so that this doesn’t require any extra steps here. NOTE: Make sure

the router’s DHCP server is the only DHCP server available on your

LAN. If there is another DHCP on your network, you’ll need to switch

one of the DHCP servers off.

3. Once your PC has obtained an

IP address from your router,

enter the default IP address —

192.168.2.1 (this is the router’s IP

address) — into your PC’s Web browser and press <Enter>.

4. When the login screen

displays, ﬁll in the “User

name” and “Password”

ﬁelds, then click “OK”

to log in. NOTE: The

default username is

“admin”; thepassword

is “1234.” For security

Download from Www.Somanuals.com. All Manuals Search And Download.

reasons, it’s recommended that you change the password as soon as

possible (see General Setup / System / Password in the user manual).

Once logged in, you can navigate through the Web-based management

user interface by selecting the

options at the top-right. To

HOME General Setup Status Tools

access the Quick Setup Wizard,

click “HOME,” then “Quick Setup” (one of the four sub-menu buttons

displayed in the left-hand menu section).

quick setuP

The Quick Setup section is designed to get you using the Wireless G

4-Port VPN Router as quickly as possible. To conﬁgure the router as

more than just an Internet access device — taking advantage of the many

features and functions — refer to the user manual on the enclosed CD.

In Quick Setup, you’re only shown how to enter the information needed

to access the Internet. Once you click “Quick Setup Wizard” on the

HOME page, you should see the Time Zone screen below.

Time Zone

Your router will base its time on the settings conﬁgured here, which will

affect functions such as log entries and ﬁrewall settings.

Download from Www.Somanuals.com. All Manuals Search And Download.

Set Time Zone — Select the time zone of the country or region you’re in.

The router will set its time based on your selection.

Time Server Address — In case the default time server isn’t working, you

can manually assign a time server address in this ﬁeld.

Daylight Saving — For the router to account for Daylight Saving changes,

select “Enable Function” and use the drop-down menus to select the

time period you want the function to take effect.

Click “Next” to affect any changes and advance to the next screen.

Broadband Type

Select the type of connection you’ll be using to connect your router’s WAN

port to your Internet service provider. As different ISPs require different

methods of connecting to the Internet, check as to the type of connection

your ISP requires. Click “Back” to return to the previous screen.

Download from Www.Somanuals.com. All Manuals Search And Download.

Broadband Type: Cable Modem

Select if your ISP will automatically give you an IP address. Some ISPs

require that you provide additional information, such as host name and

MAC address (as shown below).

Host Name — If your ISP requires a host name, enter the host name it

provides; otherwise, leave it blank

MAC Address — Enter the PC’s MAC address originally assigned by your

ISP. As an option, you can click “Clone MAC Address” to replace the

router’s WAN MAC address with the initial MAC address of that PC.

NOTE: You have to be using that PC in order for the Clone MAC

Address feature to work.

Click “OK” to ﬁnish the Cable Modem conﬁguration; then you can start

using the router.

Fixed IP xDSL

Select if your Internet service provider has given you a speciﬁc IP address

for you to use. Your ISP should provide all the information required in

this section.

IP address assigned by your Service Provider — Enter the IP address

that your ISP has given you.

Subnet Mask — Enter the subnet mask provided by your ISP (for example,

255.255.255.0).

DNS — Enter the ISP’s DNS server IP address.

Gateway Address — Enter the ISP’s IP address gateway.

Download from Www.Somanuals.com. All Manuals Search And Download.

Enter the IP Address, Subnet Mask, Gateway IP Address and DNS IP Address

provided to you by your ISP in the appropriate ﬁelds.

Click “OK” to ﬁnish the Fixed IP xDSL conﬁguration; then you can start

using the router.

PPPoE

Select if your ISP requires the PPPoE protocol to connect you to the

Internet. Your ISP should provide all information required in this section.

User Name — Enter the username provided by your ISP for the PPPoE

connection.

Password — Enter the password provided by your ISP for the PPPoE

connection.

Service Name — This is optional. Enter the provided service name if

your ISP requires it; otherwise, leave this ﬁeld blank.

MTU — Enter the MTU value provided by your ISP for the PPPoE

connection.

Connection Type — Choose one of three drop-down menu options:

• “Continuous”: Keeps the router connected to the ISP. If the WAN

connection is disrupted and then re-linked, the router will automatically

reconnect to the ISP.

• “Connect On Demand”: Auto-connects the router to the ISP when

a user wants to use the Internet, and keeps it connected until the

WAN idle timeout. The router will close the WAN connection if the

Download from Www.Somanuals.com. All Manuals Search And Download.

Enter the Username and Password required by your ISP in the appropriate ﬁelds.

If your ISP has provided you with a Service Name, enter it in that ﬁeld; otherwise,

leave the ﬁeld blank.

time period of Internet non-use exceeds the Idle Time setting.

• “Manual”: Connects the router to the ISP only when you click

“Connect” on the Web user interface. The WAN connection will not

disconnect due to the idle timeout, and if the WAN connection is

disrupted and re-linked, the router will not auto-connect to the ISP.

Idle Time — You can specify an idle-time threshold (in minutes) for the

WAN port. If no packets have been sent (no one has been using the

Internet) throughout this speciﬁed period, the router will automatically

disconnect from your ISP.

Click “OK” to ﬁnish the PPPoE conﬁguration; then you can start using

the router.

PPTP

Select if your Internet service provider requires the PPTP protocol to

connect you to the Internet. Your ISP should provide all the information

required in this section.

Obtain an IP address automatically — When this is selected, you obtain

an IP address via the DHCP before connecting to the PPTP server.

Download from Www.Somanuals.com. All Manuals Search And Download.

Point-to-Point Tunneling Protocol is a common connection method used in

xDSL connections.

Use the following IP address — When this is selected, the ISP gives

you a static IP to be used to connect to the PPTP server.

MAC Address — Enter the PC’s MAC address originally assigned by your

ISP. As an option, you can click “Clone MAC Address” to replace the

router’s WAN MAC address with the initial MAC address of that PC.

NOTE: You have to be using that PC in order for the Clone MAC

Address feature to work.

IP Address — This is the IP address that your ISP has given you to

establish a PPTP connection.

Download from Www.Somanuals.com. All Manuals Search And Download.

Subnet Mask — Enter the subnet mask provided by your ISP (for

example, 255.255.255.0).

Default Gateway — Enter the IP address of the ISP gateway.

User ID — Enter the username provided by your ISP for the PPTP

connection.

Password — Enter the password provided by your ISP for the PPTP

connection.

PPTP Gateway — If your LAN has a PPTP gateway, enter that PPTP

gateway IP address here. If you do not have a PPTP gateway, enter

the ISP’s gateway IP address (listed above).

Connection ID — This is the ID given by the ISP. This is optional.

MTU — Enter the MTU value provided by your ISP for the PPTP

connection.

BEZEQ-ISRAEL — Select if you are using the service provided by Bezeq

in Israel.