SB-GM-ESC(ESV)/10W1v2 INSTR_SKU# 011303
INSTALLATION
D I F F I C U LT Y :
If you choose to perform the installation yourself, it is absolutely vital that
the Stealthbox® be properly mounted to the vehicle according to these
instructions. Failure to mount the enclosure properly presents two problems:
OUT
OF
I N S T A L L A T I O N G U I D E
for the
1) The sub-bass performance will suffer due to the movement of the enclosure
caused by the force exerted by the woofer(s).
25
SB-GM-ESCESV/10W1v2
2) A loose enclosure presents a serious safety hazard in the event of a collision
or sudden deceleration.
ESTImATED TImE:
2 HOUrS
SB-GM-ESC/10W1v2
SKU#94476-94479 & 94483-94486
2007+
S T E P
1
These instructions are for both the short and long
wheelbase versions of this popular SUV.
OR
Empty out the back of the vehicle so that you have a clean
area to work in.
Remove the pocket in the rear quarter interior trim panel on
the drivers side of the vehicle by pulling it up and out. The
wire to power the Stealthbox® needs to come from this open
area, now would be a good time to run that wire. Leave
enough extra to make it easy to make the connection to the
Stealthbox® before it is permanently mounted.
Thank you for choosing a JL Audio Stealthbox® for your automotive sound system. With proper
installation, your new vehicle-specific enclosed subwoofer system will deliver years of listening pleasure.
S T E P
2
Looking down through the hole where the pocket had been,
notice the three studs installed at the factory. These studs
will be used to hold down the enclosure.
We strongly recommend that you have your new Stealthbox® installed by your authorized JL Audio
dealer. The installation professionals employed by your dealer have the necessary tools and experience
to disassemble and reassemble your vehicle properly. Also, keep in mind that your warranty coverage
extends to 2 years if your system is installed or approved by your authorized JL Audio dealer. If you
prefer to perform your own installation, please read this installation guide completely
before beginning the process.
S T E P
3
The Triangular Plate will be positioned as shown with center
the hole closest to the stud pointing towards the center of
the vehicle..
Continued on Next Page
Download from Www.Somanuals.com. All Manuals Search And Download.
SB-GM-ESC(ESV)/10W1v2 INSTR_SKU# 011303
I N C L U D E D H A r D W A r E
S T E P 1 2
1) Triangular Plate
4) 1/4” Flat Washer
2) 1/4-20 x 1” Hex Head Bolt
2) 3/8-16 x 1 3/4” Hex Head Bolt
2) 1/4-20 Speed Nut
1) Custom Bracket
With the bottom of the Custom Bracket bolted in and
aligned as described in Step 11 drill a hole through the
pillar corresponding with the upper hole in the Custom
Bracket as shown.
3) 3/8” Split Lock Washer
2) 1/4” Split Lock Washer
2) 3/8-16 Hex Nut
2) 1/4-20 x 1” Hex Head Bolt
2) 3/8 x 2” Fender Washer
2) 3/8 x 1-1/4” Fender Washer
****CAUTION****
Before drilling, always make sure that you are not
going to be drilling into any gas lines, brake lines,
tires, transmission lines, electrical wiring, exhaust
systems or anything else that might cause a
reduction in your weekly pay. Always wear eye
protection when drilling!
S P E C I F I C A T I O N S
Enclosure Type: Acoustic Suspension (sealed)
Driver Type: (2) 10W1v2-4
Nominal Impedance: 4Ohms per woofer, 2Ohm final load
Continuous Power Handling: 600 Watts
S T E P 1 3
P O W E r r E C O m m E N D A T I O N
From inside the rear pillar, feed the 1/4-20 x 1” Hex Head Bolt
and 1/4” Flat Washer through the hole drilled in STEP 12 as
shown.
JL Audio recommends high quality amplifiers such as the JL Audio HD900/5, 500/1v2, XD600/1 or J2 500.1. The
diagram below shows the recommended crossover, infrasonic filter and equalizer settings for the 500/1v2. If
another amplifier is being used, please reference this illustration and use similar settings on that amplifier.
A suggestion on how to get the hardware through the hole
and held in place is shown below.
+12VDC Ground Remote
Preamp Output Section
Output Mode Filter Slope
Infrasonic Filter
“Q”
1.6
Center Freq.
40
Boost (dB)
+10
+13
Amp LP Filter
Amplifier Input Section
Subwoofer Output
|
Mode
Mode Slope
Input Voltage Input Sens. Signal Sensing
1.1
0.7
0.5
2.7 30
60 +4
75
80
25
|
|
|
|
|
|
|
|
Full Range Amp Filter Out Filter
12dB 24dB
Off On
4.3 20
0
+15 Off 12dB 24dB
Low High
Off On
65
30
65
Filter Mode
Bass EQ
55
45
40
Filter Freq. (Hz)
80
100
200
22
18
15
Infrasonic Freq. (Hz)
45
55
60
55
45
40
Filter Freq. (Hz)
80
100
200
Advanced
Bass
Control
500/1v2
MONO OUTPUT ONLY
Monoblock Subwoofer Amplifier
|
|
LP HP
Off On
Left Output Right Output
Remote Bass Port
Left Ch.
Right Ch.
All JL Audio amplifiers are very versatile audio components. Please consult the owner’s manual for even more
detailed information about installing and tuning your amplifier.
D E T A I L
One way to get the Hex Head Bolt and Flat Washer installed
from the inside of the rear pillar out is to tape them to a
wrench and then guide them through the recently drilled
hole. Once this hardware is in place, tighten all of the
hardware that secures the Custom Bracket in location. With
the Custom Bracket securely installed, replace the upper rear
quarter window trim molding that was removed in STEP 7.
C O N N E C T I O N S
Using quality power, signal and speaker wire is essential in ensuring the performance of your Stealthbox®.
JL Audio recommends using a 4 AWG power kit such as the XC-PCS4-1B for your Stealthbox® amplifier, other
kits are available should you be using more than one amplifier. Signal wire such as the JL Audio Premium
Audio Interconnect Cables should be used that will provide signal for both channels of the amplifier. JL Audio
reccommends using 12AWG speaker wire for subwoofers such as our XC-BCS12-25.
Connect the speaker cables from the amplifier and set the
Stealthbox® in place.
m I D / H I G H F r E q U E N C Y D r I V E r F I T m E N T
A variety of JL Audio coaxial and component systems will fit in the factory speaker locations of you vehicle.
S T E P 1 5
Front Speaker Size / Location: 6-1/2”- Front Doors
Install the mounting 3/8-16 x 1 3/4” Hex Head Bolt, Split Lock
Washer and Flat Washer through the enclosure wall into the
Speed Nut shown in STEP 11. Also install the Hex Nut, Split
Lock Washer and, Flat Washer on the stud that protrudes
into the bottom of the Stealthbox® from the Triangular
Plate installed in STEP 5. Re-install the woofers into the
Stealthbox®.
Fits JL Audio Models: TR650-CXi, C2-650x, C3-650, C5-650, C5-650x & ZR650-CSi
Rear Speaker Size / Location: 6-1/2”- Rear Door
Fits JL Audio Models: TR650-CXi, C2-650x, C3-650, C5-650, C5-650x & ZR650-CSi
C O N G r A T U L A T I O N S !
You have completed the installation for this model!
Enjoy your new Stealthbox®! Please refer to the Power
Recommendation section for an amplifier recommendation
and basic set-up help.
(954) 443-1100
All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered
trademarks of JL Audio, Inc. “Ahead of the Curve”and its respective logo is a trademark of JL Audio, Inc.
JLA-SKU# 011303 02.15.2010
•
Printed in USA
•
©2010 JL Audio, Inc.
•
U.S. PATENTS: #5,734,734 #5,949,898 #6,118,884 #6,229,902 #6,243,479
#6,294,959 #6,501,844 #6,496,590 #6,441,685 #5,687,247 #6,219,431 #6,625,292 #D472,891 #D480,709 Other U.S. & Foreign patents pending.
1
0
3
6
9
N
O
R
T
H
C
O
M
M
E
R
C
E
P
A
R
K
W
A
Y
•
M
I
R
A
M
A
R
,
F
L
O
R
I
D
A
•
3
3
0
2
5
•
U
S
A
Page 3 • JL Audio, Inc 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
|