®
SYNTHESIS
SDEC-3000
SDEC-4000
DIGITAL
EQUALIZER
INSTALLER’S
MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY PRECAUTIONS!
PLEASE READ CAREFULLY ALL OF THE FOLLOWING IMPORTANT SAFEGUARDS THAT ARE
APPLICABLE TO YOUR EQUIPMENT
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus
(including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong.
The wide blade or the third prong is provided for your safety. If the provided plug does not fit into
your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles and
the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket or table specified by the manufacturer or sold with the apparatus.
When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord
or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
15. Do not use attachments not recommended by the product manufacturer, as they may cause hazards.
16. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply
to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to
the operating instructions.
17. If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection
against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to
proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors,
location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. See Figure A.
18. An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall
into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or
circuits, as contact with them might be fatal.
19. Do not overload wall outlets, extension cords, or integral convenience receptacles, as this can result in a risk of fire or electric shock.
20. Never push objects of any kind into this product through openings, as they may touch dangerous voltage points or short-out parts that could result in
a fire or electric shock. Never spill liquid of any kind on the product.
21. The apparatus shall not be exposed to dripping or splashing, and no objects filled with liquids, such as vases, shall be placed on the apparatus.
22. Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
23. When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or that have the same
characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.
24. Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in
proper operating condition.
25. The product should be mounted to a wall or ceiling
only as recommended by the manufacturer.
Figure A.
Example of Antenna Grounding as per
National Electrical Code ANSI/ NFPA 70
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s
attention to Article 820-22 of the NEC that provides
guidelines for proper grounding and, in particular, specifies
that the cable ground shall be connected to the grounding
system of the building, as close to the point of cable
entry as practical.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION AND FEATURES
INTRODUCTION
Congratulations on your purchase of this JBL Synthesis® SDEC Digital Equalizer! You have chosen a product that
®
embodies the best of what JBL has discovered about the emotional power of audio reproduction in more than sixty
years of preeminence in the field. This Digital Equalizer has been designed and crafted to provide the user with a
high level of sonic performance; special attention has been paid to minimize the number of components in the audio
signal path, resulting in extremely low distortion, excellent transient response and wide dynamic range. Synthesis
products set new benchmarks in audio technology, and, when used as part of a complete JBL Synthesis system,
will bring the ambience and acoustics of some of the world’s greatest concert halls and theaters into your home.
To obtain the best performance from this Digital Equalizer, please be sure to completely read this user’s manual
and use the SDEC Digital Equalizer only in accordance with its instructions.
From its inception, JBL Synthesis has been the answer to the questions: “How do you build a state-of-the-art
home theater system and make it sound superb in every installation? How can you be sure all the hardware is
compatible?” These were the big questions fifteen years ago; Synthesis was the answer. Once again, JBL Synthesis
moves beyond the competition and is the answer. The JBL Synthesis Digital Equalizer (SDEC) is a (up to) 12-channel-
in/20-channel-out 24-bit, 96kHz digital audio signal processor. Unlike nearly all other audio components on the
market, the SDEC has been designed to work specifically with other Synthesis System components. This narrow
application focus has allowed our engineers to design a product with far fewer compromises, resulting in
unequalled system performance. By reading the following pages, you will become familiar with the technological
features and unique capabilities incorporated within the SDEC and available nowhere else.
Until now, anything beyond the most basic equalization has been impossible without expensive acoustical instru-
mentation and the knowledge to use it. This is why, traditionally, equalizers have been general-purpose devices,
designed to be applicable to any audio system, usually of doing more harm than good! Add to this situation the fact
that equalizing a speaker system by ear is truly a futile exercise. This helps to account for the generally low
acceptance of equalizers outside of professional audio applications.
FEATURES
• Up to 120 bands of fully parametric EQ
• Built-in crossover for bi-amp outputs (SDEC-4000 only)
• Delay adjustment for each output
• Delay adjustment for driver compensation
• Four subwoofer outputs (SDEC-4000 only)
• Two pairs of side speaker outputs for large rooms with multiple rows of seating (SDEC-4000 only)
• 24-Bit DSP
• 96kHz sample rate on all inputs and outputs
• Balanced or Single-Ended (unbalanced) inputs and outputs
4
Download from Www.Somanuals.com. All Manuals Search And Download.
DETAILED DIAGRAM – FRONT PANEL
2
4
6
5
3 1
0
0 INPUT/OUTPUT CARD MONITORING
Each channel has three LED indicators showing:
CLIP
Illuminated – Indicates clipping in the analog domain for each channel of the fitted Input or Output card.
The LED will light at +18.5dB.
SIGNAL
Illuminated – The Signal LED will light for each channel of a fitted Input or Output card when the signal
reaches or exceeds the signal threshold of –20dB.
PHANTOM
This feature is currently not supported by JBL Synthesis (lights to indicate +48V phantom power has
been activated for the relevant channel of a fitted input card).
1 USB
This is currently for future use and is not supported.
2 DATA ACTIVITY
The Data Activity LED will flash to indicate that the device is communicating with another control device, either
on the network or via the USB, serial or control ports.
3 NETWORK LINK
The Network Link indicates the presence of Cat. 5 Ethernet cables. If no cables are connected, the LED is unlit;
the LED flashes if either a control or CobraNet® cable is fitted, and remains illuminated if both cables are connected.
The network link is used for configuring and calibrating the Synthesis System when using the DACS calibration,
and for system status when using the SDEC-4000.
4 LCD (LIQUID CRYSTAL DISPLAY)
Indicates the name/ID and IP address of the unit.
5 CONTRAST (HOLD)
Pressing and holding the Locate switch will cycle the LCD through its contrast range.
6 LOCATE
Pressing the Locate switch on the front of the unit will illuminate the Locate switch on the rear and identify the
device within the DACS software.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
DETAILED DIAGRAM – REAR PANEL
SDEC-3000
8
C
D
7
9A
E
B
SDEC-4000P and
SDEC-4000X
SDEC-3000 has no CobraNet or Word Clock connections, but is otherwise identical to the SDEC-4000P and SDEC-4000X.
7 AC MAINS
AC Mains input to the universal switched-mode power supply, operates over a wide range of AC input voltages
from 85V to 270V, 50/60Hz.
8 LOCATE
Pressing the Locate switch on the rear of the unit will illuminate the Locate switch on the front and identify the
device within the DACS software.
9 COBRANET CONNECTORS
Primary/Secondary: The SDEC-4000P and SDEC-4000X use CobraNet to send and receive audio data. During normal
operation, the Primary port only receives audio data from and transmits audio data to the network. Should the
Primary port or connection fail, the CobraNet module automatically switches to receive from and transmit with the
Secondary port. This is an optional connection.
Please Note: When using the SDEC-4000, you must connect the two units through the CobraNet connection, using
a Cat. 5e crossover cable.
A RS-232
Serial port for connection of external calibration and configuration equipment not used at this time.
B ETHERNET
The main connection for the proprietary system control network, and for third-party Ethernet control. The SDEC-4000
must be connected to an Ethernet hub during the calibration process. The SDEC-3000 can be connected directly to
a PC using a crossover Cat. 5 Ethernet cable.
C BUDDYLINK/48K
This connection is not supported at this time.
D CONTROL INPUTS
The SDEC-4000 can be configured for full-range or bi-amp operation by using these control inputs. The SDEC-3000
does not need or use this connection.
E I/O CARD POSITIONS A, B, C AND D
These connectors provide the balanced and unbalanced connections for the I/O card fitted in the four card
slots in a JBL Synthesis SDEC device. A green LED next to the slot assignment letter A, B, C or D indicates that an
Input card is fitted and an amber LED when an output card is fitted. The analog connections are balanced/unbal-
anced, on Phoenix/Combicon connectors. Depending on which model and configuration you have purchased will
determine which I/O card has been installed at the factory. Please make sure to order the correct wiring kit, either
S3000IC or S4000IC, with your system.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
INPUT/OUTPUT ASSIGNMENTS
SDEC-3000
The SDEC-3000 supports up to 7.1 input with up to 7.1 output. The input and output assignments are as described
in the below chart. You must make the correct connections from the surround processor output to the amplifier input
for the system to work correctly. Please refer to the connection diagram for more information.
The correct Synthesis Interconnect kit includes all the necessary connections for using the SDEC in the Synthesis
system. Please be sure to order the S3000IC for use with SDEC-3000 and S4000IC for use with SDEC-4000. Retrofit kits
are also available. Please contact JBL Synthesis Technical Support for more information at (888) 691-4171 (USA only).
CONNECTION NOTES
• Please follow the wiring diagram and the Input/Output Assignments chart for correct connections.
• You will need to use the Ethernet network port on the rear panel of the unit for the final calibration process.
You can use a crossover network cable if you plan to connect directly to the SDEC-3000 from a computer.
Alternatively, you can connect the SDEC-3000 through any standard Ethernet hub.
• When using the SDP-40 processor, make sure the subwoofer (in speaker setup) is set to Mono output and connect
to the Subwoofer Left output.
Input/Output Assignments
Surround Processor to SDEC-3000 Inputs
S3000IC
Number
Channel
SDEC-3000
1
2
3
4
5
6
7
8
LEFT FRONT
RIGHT FRONT
CENTER FRONT
LEFT SIDE
RIGHT SIDE
LEFT REAR
RIGHT REAR
SUBWOOFER
(Mono Sub Left)
A1
A2
A3
A4
B1
B2
B3
B4
SDEC-3000 Outputs to Amplifiers
S3000IC
Number
9
10
11
12
Channel
LEFT FRONT
RIGHT FRONT
CENTER FRONT
LEFT SIDE
SDEC-3000
C1
C2
C3
C4
D1
D2
D3
D4
13
14
RIGHT SIDE
LEFT REAR
15
16
RIGHT REAR
SUBWOOFER
7
Download from Www.Somanuals.com. All Manuals Search And Download.
INPUT/OUTPUT ASSIGNMENTS
SDEC-4000
The SDEC-4000 comprises two units. Both the SDEC-4000P and SDEC-4000X are required for the digital equalizer
to function properly in the Synthesis system. Please be sure to connect both units correctly according to the
Input/Output Assignments chart.
The correct Synthesis Interconnect kit includes all the necessary connections for using the SDEC in the Synthesis
System. Please be sure to order the S3000IC for use with SDEC-3000 and S4000IC for use with SDEC-4000. Retrofit kits
are also available. Please contact JBL Synthesis Technical Support for more information at (888) 691-4171 (USA only).
The SDEC-4000 is capable of processing up to 12 inputs and up to 20 outputs. Depending on the type and number
of outputs will determine which connections you should use to connect the SDEC to the rest of your system. Please
refer to the connection diagram for more information.
CONNECTION NOTES
• The SDEC-4000 can process two outputs for the front left, center and right channels to output to an amplifier
for a Bi-amplified system. There are discrete outputs for a single high-frequency horn speaker (SAM1HF) and
low-frequency (SAM2LF) speakers. These outputs can only be used with speakers designed to be used with an
external crossover. Do not use the SDEC Digital Equalizer for any speakers other than the recommended
Synthesis speaker packages.
• There are two pairs of outputs for side speakers. If you are only using one pair of side speakers you may leave
the second pair of outputs with no connection. If you are using a second pair of side speakers, you should connect
the pair closest to the front speakers to output 1 and the pair closest to the rear speakers to output 2.
• There are up to four subwoofer outputs. You should use them in pairs so that you either have two or four
subwoofers. All Synthesis systems are designed for at least two subwoofers.
• You must connect the SDEC-4000P and the SDEC-4000X using the CobraNet connection, using an Ethernet
network crossover cable, Cat. 5e minimum.
• The two units must be connected to an Ethernet network hub for the final calibration process. Both units need
to be connected to the same hub or router, and an open port needs to be accessible for the calibration computer.
• When using the SDP-40 processor, make sure the subwoofer (in speaker setup) is set to Mono output and connect
to the Subwoofer Left output.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
INPUT/OUTPUT ASSIGNMENTS
SDEC-4000 WITH BI-AMPLIFIED FRONT SPEAKERS
This configuration requires the selection of bi-amplified operation, as noted on page 11.
Input/Output Assignments
Surround Processor to SDEC-4000P Inputs
S4000IC
Number
Channel
FRONT LEFT
FRONT RIGHT
CENTER FRONT
LEFT SIDE
RIGHT SIDE
LEFT REAR
RIGHT REAR
SUBWOOFER
(Mono Sub L)
N/C
SDEC-4000P
1
2
3
4
5
6
7
8
A1
A2
A3
A4
B1
B2
B3
B4
C1
C2
C3
C4
N/C
N/C
N/C
SDEC-4000X Outputs to Amplifiers
S4000IC
Number
9
10
11
12
13
14
15
16
Channel
LEFT FRONT-LOW
LEFT FRONT-HI
RIGHT FRONT-LOW
RIGHT FRONT-HI
CENTER FRONT-LOW
CENTER FRONT-HI
LEFT SIDE 1
LEFT SIDE 2
N/C
SDEC-4000X
Amplifier
S5160 #1
S5160 #1
S5160 #1
S5160 #1
S5160 #2
S5160 #2
S5160 #2
optional
–
Input Channel
A1
A2
A3
A4
B1
B2
B3
B4
C1
C2
C3
C4
D1
D2
D3
D4
CH1
CH2
CH3
CH4
CH1
CH2
CH3
–
–
–
CH4
–
–
N/C
–
17
18
RIGHT SIDE 1
RIGHT SIDE 2
N/C
S5160 #2
optional
–
N/C
–
–
CH5
CH5
19
20
LEFT REAR
RIGHT REAR
S5160 #1
S5160 #2
SDEC-4000P Outputs to Amplifiers
Number
21
22
23
24
Channel
SDEC-4000P
SUBWOOFER 1
SUBWOOFER 2
SUBWOOFER 3
SUBWOOFER 4
D1
D2
D3
D4
S800 #1
S800 #2
CH1 (bridged)
CH1 (bridged)
S800 #3 (optional) CH1 (bridged)
S800 #4 (optional) CH1 (bridged)
9
Download from Www.Somanuals.com. All Manuals Search And Download.
INPUT/OUTPUT ASSIGNMENTS
SDEC-4000 WITH FULL-RANGE FRONT SPEAKERS
This is the default configuration.
Input/Output Assignments
Surround Processor to SDEC-4000P Inputs
S4000IC
Number
Channel
FRONT LEFT
FRONT RIGHT
CENTER FRONT
LEFT SIDE
RIGHT SIDE
LEFT REAR
RIGHT REAR
SUBWOOFER
(Mono Sub L)
N/C
SDEC-4000P
1
2
3
4
5
6
7
8
A1
A2
A3
A4
B1
B2
B3
B4
C1
C2
C3
C4
N/C
N/C
N/C
SDEC-4000X Outputs to Amplifiers
S4000IC
Number
9
Channel
LEFT FRONT
N/C
SDEC-4000X
Amplifier
S800 #1
–
S800 #2
–
S800 #3
–
S7150 #1
S7150 #1
–
Input Channel
CH1 (bridged)
A1
A2
A3
A4
B1
B2
B3
B4
C1
C2
C3
C4
D1
D2
D3
D4
10
–
11
12
RIGHT FRONT
N/C
CH1 (bridged)
–
13
14
CENTER FRONT
N/C
CH1 (bridged)
–
15
16
LEFT SIDE 1
LEFT SIDE 2
N/C
CH1
CH2
–
N/C
–
–
17
18
RIGHT SIDE 1
RIGHT SIDE 2
N/C
S7150 #1
S7150 #1
–
CH3
CH4
–
–
CH5
CH6
N/C
–
19
20
LEFT REAR
RIGHT REAR
S7150 #1
S7150 #1
SDEC-4000P Outputs to Amplifiers
S4000IC
Number
Channel
SDEC-4000P
21
22
23
24
SUBWOOFER 1
SUBWOOFER 2
SUBWOOFER 3
SUBWOOFER 4
D1
D2
D3
D4
S800 #4
S800 #5
S800 #6
S800 #7
CH1 (bridged)
CH1 (bridged)
CH1 (bridged)
CH1 (bridged)
10
Download from Www.Somanuals.com. All Manuals Search And Download.
INPUT/OUTPUT ASSIGNMENTS
SELECTING BI-AMPED CONFIGURATION
There Are Two Ways to Select Bi-Amped LCR Operation.
SELECTING FULL-RANGE CONFIGURATION
There Are Two Ways to Select Full-Range LCR Operation.
Please Note: Only Method One can be done on the control ports
(without a computer). Method Two requires a computer running
the appropriate configuration software. Please contact JBL
Synthesis Technical Support for more information.
Please Note: Only Method One can be done on the control ports
(without a computer). Method Two requires a computer running
the appropriate configuration software. Please contact JBL
Synthesis Technical Support for more information.
METHOD ONE:
METHOD ONE:
With the unit powered up and running, connect Control
With the unit powered up and running, connect Control Input 1
Input 2 to “C” for bi-amped.
to “C” (common) on the back of the unit for full-range.
METHOD TWO:
While online and in operate mode from within London
Architect, select the “Main” page and then click on the
full-range button.
METHOD TWO:
While online and in operate mode from within London
™
Architect , select the “Main” page and then click on the
bi-amped button.
NOTE: The full-range configuration is the default and will
not require selection during normal use.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTION TO THE REST OF THE JBL SYNTHESIS SYSTEM
SDEC-3000
SDP-5
NOTE: Although the
SDP-5 is shown here,
connections for the
SDP-40 are similar.
SDP-5 Digital Surround Processor/Controller
INPUTS
MAIN
ZONE
2
JBL, Inc. Northridge, CA
Assembled in USA
S/PDIF INPUTS
2
1
3
2
4
TUV
INPUT
1
INPUT
2
Y
Y
PR
PR
PB
PB
Y
Y
PR
PR
PB
PB
C
US
1
1
1
2
2
3
4
4
5
5
VIDEO
VIDEO
AUDIO
CAUTION
S/N
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ATTENTION
RISQUE DE CHOC
ELECTRIQUE
3
4
NE PAS OUVRIR
OUTPUT
CENTER
INPUT
7
3
IR IN
3
6
8
FRONT
SIDE
REAR
TRIGGER
OUTPUTS
(L)
(R)
(C)
(LS)
(RS)
(L)
(R)
(C)
(LS)
(RS)
L
L
L
S/PDIF
OUT
1
2
RS-232
(SUB)
(SUB)
R
R
R
SUBWOOFER
OUTPUTS
1
2
AC 100-240V ~ 50-60 HZ, 60W
SDEC-3000
To Ethernet hub
(for system calibration)
S7150
JBL SYNTHESIS
NORTHRIDGE, CA
NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED PERSONNEL
DESIGNED, ENGINEERED AND MANUFACTURED
IN THE UNITED STTES OF AMERICA
TRIGGERS
IN
S5160 POWER AMPLIFIER
Ch. 1
Input
Ch. 2
Input
Ch. 3
Input
Ch. 4
Input
Ch. 5
Input
Ch. 6
Input
Ch. 7
Input
SPKR-1
SPKR-2
OUT
MANUAL
ON
AUTO
ON
ON
15A
120V
50/60Hz
1800W
~
OFF
WARNING: HAZARDOUS ENERGY, MAKE PROPER SPEAKER CONNECTIONS; SEE OWNERS MANUAL BEFORE USING.
WARNING: To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture
ATTENTION:
VOIR LE CAHIER D'
INSTRUCTION
+
+
+
+
+
+
+
-
-
-
-
-
-
-
serial number
Ch. 1 Output
Ch. 2 Output
Ch. 3 Output
Ch. 4 Output
Ch. 5 Output
Ch. 6 Output
Ch. 7 Output
S800
VOIR LE CAHIER D'
INSTRUCTION
JBL SYNTHESIS
NORTHRIDGE, CA
DESIGNED, ENGINEERED AND MANUFACTURED
IN THE UNITED STATES OF AMERICA
ATTENTION:
TRIGGERS
IN
S800 POWER AMPLIFIER
BRIDGED
Ch. 1
BRIDGED
Input
Ch. 2
Input
WARNING; To reduce the risk of fire or
electric shock, do not expose
MONO
STEREO
this appliance to rain or moisture
OUT
No user serviceable parts inside. Refer
servicing to qualified personnel.
AUTO
ON
MANUAL
ON
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS:
RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
ON
10A
120V
50/60Hz
1200W
~
OFF
HAZARDOUS ENERGY, MAKE PROPER SPEAKER CONNECTIONS; SEE OWNERS MANUAL BEFORE USING.
WARNING:
serial number
BRIDGED
+
+
-
+
-
-
Ch. 1 Output
Ch. 2 Output
12
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTION TO THE REST OF THE JBL SYNTHESIS SYSTEM
SDEC-4000 With Bi-Amplified Speakers
SDP-5
SDP-5 Digital Surround Processor/Controller
INPUTS
MAIN
ZONE
2
JBL, Inc. Northridge, CA
Assembled in USA
NOTE: Although the
SDP-5 is shown here,
connections for the
SDP-40 are similar.
S/PDIF INPUTS
2
1
3
2
4
TUV
INPUT
1
INPUT
2
Y
Y
PR
PR
PB
PB
Y
Y
PR
PR
PB
PB
C
US
1
1
1
2
2
3
3
4
4
5
5
VIDEO
VIDEO
AUDIO
CAUTION
S/N
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ATTENTION
RISQUE DE CHOC
ELECTRIQUE
3
4
NE PAS OUVRIR
OUTPUT
CENTER
INPUT
7
3
IR IN
6
8
FRONT
SIDE
REAR
TRIGGER
OUTPUTS
(L)
(R)
(C)
(LS)
(RS)
(L)
(R)
(C)
(LS)
(RS)
L
L
L
S/PDIF
OUT
1
2
RS-232
(SUB)
(SUB)
R
R
R
SUBWOOFER
OUTPUTS
1
2
AC 100-240V ~ 50-60 HZ, 60W
To Ethernet hub
(for system calibration)
SDEC-4000P
SDEC-4000X
To Ethernet hub
(for system calibration)
JBL SYNTHESIS
NORTHRIDGE, CA
NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED PERSONNEL
DESIGNED, ENGINEERED AND MANUFACTURED
IN THE UNITED STATES OF AMERICA
TRIGGERS
IN
S5160 POWER AMPLIFIER
Ch.
1
Ch.
2
Ch.
3
Ch.
4
Ch.
5
Input
Input
Input
Input
Input
SPKR-1
SPKR-2
OUT
MANUAL
ON
AUTO
ON
ON
15A
120V
50/60Hz
1800W
~
OFF
WARNING: HAZARDOUS ENERGY, MAKE PROPER SPEAKER CONNECTIONS; SEE OWNERS MANUAL BEFORE USING.
ATTENTION:
VOIR LE CAHIER D'
INSTRUCTION
WARNING:
To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture
+
+
+
+
+
-
-
-
-
-
serial number
Ch.
1
Output
Ch.
2
Output
Ch.
3
Output
Ch.
4
Output
Ch.
5
Output
S5160
JBL SYNTHESIS
NORTHRIDGE, CA
NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED PERSONNEL
DESIGNED, ENGINEERED AND MANUFACTURED
IN THE UNITED STATES OF AMERICA
TRIGGERS
IN
S5160 POWER AMPLIFIER
Ch.
1
Ch.
2
Ch.
3
Ch.
4
Ch.
5
Input
Input
Input
Input
Input
SPKR-1
SPKR-2
OUT
MANUAL
ON
AUTO
ON
ON
15A
120V
50/60Hz
1800W
~
OFF
WARNING: HAZARDOUS ENERGY, MAKE PROPER SPEAKER CONNECTIONS; SEE OWNERS MANUAL BEFORE USING.
ATTENTION:
VOIR LE CAHIER D'
INSTRUCTION
WARNING:
To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture
+
+
+
+
+
-
-
-
-
-
serial number
Ch.
1
Output
Ch.
2
Output
Ch.
3
Output
Ch.
4
Output
Ch.
5
Output
S5160
VOIR LE CAHIER D'
INSTRUCTION
JBL SYNTHESIS
NORTHRIDGE, CA
DESIGNED, ENGINEERED AND MANUFACTURED
IN THE UNITED STATES OF AMERICA
ATTENTION:
VOIR LE CAHIER D'
INSTRUCTION
JBL SYNTHESIS
NORTHRIDGE, CA
DESIGNED, ENGINEERED AND MANUFACTURED
IN THE UNITED STATES OF AMERICA
TRIGGERS
ATTENTION:
IN
S800 POWER AMPLIFIER
TRIGGERS
IN
S800 POWER AMPLIFIER
BRIDGED
BRIDGED
Ch.
1
Ch.
2
Ch.
1
Ch.
2
WARNING; To reduce the risk of fire or
electric shock, do not expose
WARNING; To reduce the risk of fire or
electric shock, do not expose
BRIDGED
Input
Input
BRIDGED
Input
Input
MONO
STEREO
MONO
STEREO
this appliance to rain or moisture
this appliance to rain or moisture
OUT
OUT
No user serviceable parts inside. Refer
servicing to qualified personnel.
No user serviceable parts inside. Refer
servicing to qualified personnel.
AUTO
ON
MANUAL
ON
AUTO
ON
MANUAL
ON
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS:
RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
AVIS:
RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
ON
ON
10A
120V
50/60Hz
1200W
10A
120V
50/60Hz
1200W
~
~
OFF
OFF
HAZARDOUS ENERGY MAKE PROPER SPEAKER CONNECTIONS; SEE OWNERS MANUAL BEFORE USING.
,
WARNING:
serial number
HAZARDOUS ENERGY
,
MAKE PROPER SPEAKER CONNECTIONS; SEE OWNERS MANUAL BEFORE USING.
BRIDGED
WARNING:
serial number
+
+
BRIDGED
-
+
+
-
+
-
-
+
-
-
Ch.
1
Output
Ch.
2
Output
Ch.
1
Output
Ch.
2
Output
S800
S800
13
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTION TO THE REST OF THE JBL SYNTHESIS SYSTEM
SDEC-4000 With Full-Range Front Speakers
SDP-40
INPUTS
COMPONENT VIDEO
PB
MAIN OUTPUTS
RECORD OUTPUTS
1
2
3
4
5
INPUT 1
PR
INPUT 2
PR
INPUT 3
PR PB
Y
PB
Y
Y
NOTE: Although the
SDP-40 is shown here,
connections for the
SDP-5 are similar.
2
1
2
1 (OSD)
INPUT 4
PR
OUTPUT
PR PB
Y
PB
Y
VIDEO
VIDEO
1
2
3
4
5
6
7
8
FRONT
CENTER
SIDE
Fix ZONE 2
L
Fix
Var
SUBWOOFER
REAR
Var
AUX
(L)
(LS)
(RS)
(C)
L
L
L
L
L
(R)
(SUB)
R
R
R
R
R
R
LFE
MAIN AUDIO OUTPUTS
AUDIO
TRIGGER OUTPUTS
AUDIO
S/PDIF
MICROPHONE INPUTS
1
2
3
1
2
3
4
1
4
2
3
1
2
4
5
6
IR IN
5
6
RS 232
FRONT
CENTER
LFE
L
SUBWOOFER R
ZONE 2
L
R
L
R
L
AUX
R
L
R
L
SIDE
R
REAR
To Ethernet hub
(for system calibration)
SDEC-4000P
SDEC-4000X
To Ethernet hub
(for system calibration)
ATTENTION:
VOIR LE CAHIER D'
INSTRUCTION
JBL SYNTHESIS
NORTHRIDGE, CA
DESIGNED, ENGINEERED AND MANUFACTURED
IN THE UNITED STATES OF AMERICA
ATTENTION:
VOIR LE CAHIER D'
INSTRUCTION
JBL SYNTHESIS
NORTHRIDGE, CA
DESIGNED, ENGINEERED AND MANUFACTURED
IN THE UNITED STATES OF AMERICA
TRIGGERS
IN
TRIGGERS
IN
S800 POWER AMPLIFIER
S800 POWER AMPLIFIER
NO USER SERVICEABLE PARTS INSIDE. REFER
S5160 POWER AMPLIFIER
JBL SYNTHESIS
NORTHRIDGE, CA
DESIGNED, ENGINEERED AND MANUFACTURED
IN THE UNITED STATES OF AMERICA
TRIGGERS
IN
SERVICING TO QUALIFIED PERSONNEL
BRIDGED
BRIDGED
Ch.
1
Ch.
2
Ch.
1
Ch.
2
WARNING;
T
o
reduce the risk of fire or
WARNING;
T
o
reduce the risk of fire or
BRIDGED
Input
Input
BRIDGED
Input
Input
Ch.
1
Ch.
2
Ch.
3
Ch.
4
Ch.
5
Ch.
6
Ch.
7
electric shock, do not expose
this appliance to rain or moisture
electric shock, do not expose
this appliance to rain or moisture
MONO
STEREO
MONO
STEREO
Input
Input
Input
Input
Input
Input
Input
SPKR-1
SPKR-2
OUT
OUT
OUT
No user serviceable parts inside. Refer
servicing to qualified personnel.
No user serviceable parts inside. Refer
servicing to qualified personnel.
MANUAL
ON
AUTO
ON
MANUAL
ON
AUTO
ON
MANUAL
ON
AUTO
ON
CAUTION
RISK OF ELECTRIC SHOCK
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
DO NOT OPEN
AVIS:
RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
AVIS:
RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
ON
10A
120V~
50/60Hz
1200W
ON
10A
120V~
50/60Hz
1200W
ON
15A
120V
50/60Hz
1800W
~
OFF
OFF
WARNING:
serial number
HAZARDOUS ENERGY,
MAKE PROPER SPEAKER CONNECTIONS; SEE OWNERS MANUAL BEFORE USING.
WARNING:
serial number
HAZARDOUS ENERGY,
MAKE PROPER SPEAKER CONNECTIONS; SEE OWNERS MANUAL BEFORE USING.
+BRIDGED
+BRIDGED
-
-
OFF
WARNING: HAZARDOUS ENERGY
,
MAKE PROPER SPEAKER CONNECTIONS; SEE OWNERS MANUAL BEFORE USING.
WARNING:
To
reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture
ATTENTION:
VOIR LE CAHIER D'
INSTRUCTION
+
Output
+
-
+
Output
+
-
-
-
Ch.
1
Ch.
2
Output
Ch.
1
Ch.
2
Output
+
-
+
+
+
+
+
+
-
-
-
-
-
-
serial number
Ch.
1
Output
Ch.
2
Output
Ch.
3
Output
Ch.
4
Output
Ch.
5
Output
Ch.
6
Output
Ch.
7
Output
S800
S800
S7150
ATTENTION:
VOIR LE CAHIER D'
INSTRUCTION
JBL SYNTHESIS
NORTHRIDGE, CA
DESIGNED, ENGINEERED AND MANUFACTURED
IN THE UNITED STATES OF AMERICA
ATTENTION:
VOIR LE CAHIER D'
INSTRUCTION
JBL SYNTHESIS
NORTHRIDGE, CA
DESIGNED, ENGINEERED AND MANUFACTURED
IN THE UNITED STATES OF AMERICA
TRIGGERS
IN
TRIGGERS
IN
S800 POWER AMPLIFIER
S800 POWER AMPLIFIER
BRIDGED
BRIDGED
Ch.
1
Ch.
2
Ch.
1
BRIDGED
Input
Ch.
2
WARNING;
T
o
reduce the risk of fire or
WARNING;
T
o
reduce the risk of fire or
BRIDGED
Input
Input
Input
electric shock, do not expose
this appliance to rain or moisture
electric shock, do not expose
this appliance to rain or moisture
MONO
STEREO
MONO
STEREO
OUT
OUT
No user serviceable parts inside. Refer
servicing to qualified personnel.
No user serviceable parts inside. Refer
servicing to qualified personnel.
MANUAL
ON
AUTO
ON
MANUAL
ON
AUTO
ON
CAUTION
RISK OF ELECTRIC SHOCK
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
DO NOT OPEN
AVIS:
RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
AVIS:
RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
ON
10A
120V~
50/60Hz
1200W
ON
10A
120V~
50/60Hz
1200W
OFF
OFF
WARNING:
serial number
HAZARDOUS ENERGY,
MAKE PROPER SPEAKER CONNECTIONS; SEE OWNERS MANUAL BEFORE USING.
WARNING:
serial number
HAZARDOUS ENERGY, MAKE PROPER SPEAKER CONNECTIONS; SEE OWNERS MANUAL BEFORE USING.
+BRIDGED
+BRIDGED
-
-
+
Output
+
-
+
+
-
-
-
Ch.
1
Ch.
2
Output
Ch.
1
Output
Ch.
2
Output
S800
S800
ATTENTION:
VOIR LE CAHIER D'
INSTRUCTION
JBL SYNTHESIS
NORTHRIDGE, CA
DESIGNED, ENGINEERED AND MANUFACTURED
IN THE UNITED STATES OF AMERICA
ATTENTION:
VOIR LE CAHIER D'
INSTRUCTION
JBL SYNTHESIS
NORTHRIDGE, CA
DESIGNED, ENGINEERED AND MANUFACTURED
IN THE UNITED STATES OF AMERICA
TRIGGERS
IN
TRIGGERS
IN
S800 POWER AMPLIFIER
S800 POWER AMPLIFIER
BRIDGED
BRIDGED
Ch.
1
Ch.
2
Ch.
1
Ch.
2
WARNING;
T
o
reduce the risk of fire or
WARNING;
T
o
reduce the risk of fire or
BRIDGED
Input
Input
BRIDGED
Input
Input
electric shock, do not expose
this appliance to rain or moisture
electric shock, do not expose
this appliance to rain or moisture
MONO
STEREO
MONO
STEREO
OUT
OUT
No user serviceable parts inside. Refer
servicing to qualified personnel.
No user serviceable parts inside. Refer
servicing to qualified personnel.
MANUAL
ON
AUTO
ON
MANUAL
ON
AUTO
ON
CAUTION
RISK OF ELECTRIC SHOCK
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
DO NOT OPEN
AVIS:
RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
AVIS:
RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
ON
10A
120V~
50/60Hz
1200W
ON
10A
120V~
50/60Hz
1200W
OFF
OFF
WARNING:
serial number
HAZARDOUS ENERGY,
MAKE PROPER SPEAKER CONNECTIONS; SEE OWNERS MANUAL BEFORE USING.
WARNING:
serial number
HAZARDOUS ENERGY, MAKE PROPER SPEAKER CONNECTIONS; SEE OWNERS MANUAL BEFORE USING.
+BRIDGED
+BRIDGED
-
-
+
Output
+
-
+
Output
+
-
-
-
Ch.
1
Ch.
2
Output
Ch.
1
Ch.
2
Output
S800
S800
ATTENTION:
VOIR LE CAHIER D'
INSTRUCTION
JBL SYNTHESIS
NORTHRIDGE, CA
DESIGNED, ENGINEERED AND MANUFACTURED
IN THE UNITED STATES OF AMERICA
TRIGGERS
IN
S800 POWER AMPLIFIER
BRIDGED
Ch.
1
Ch.
2
WARNING;
T
o
reduce the risk of fire or
BRIDGED
Input
Input
electric shock, do not expose
this appliance to rain or moisture
MONO
STEREO
OUT
No user serviceable parts inside. Refer
servicing to qualified personnel.
MANUAL
ON
AUTO
ON
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS:
RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
ON
10A
120V~
50/60Hz
1200W
OFF
WARNING:
serial number
HAZARDOUS ENERGY, MAKE PROPER SPEAKER CONNECTIONS; SEE OWNERS MANUAL BEFORE USING.
+BRIDGED
-
+
Output
+
-
-
Ch.
1
Ch.
2
Output
S800
14
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
INPUTS UP TO 12 ANALOG; ELECTRONICALLY BALANCED ON PHOENIX/COMBICON REMOVABLE SCREW CONNECTORS
MIC/LINE INPUTS:
NOMINAL GAIN 0DB, ELECTRONICALLY SWITCHABLE UP TO +48DB, IN +6DB STEPS,
INPUT IMPEDANCE 3.5K OHMS
MAXIMUM INPUT LEVEL:
CMRR:
+20DBU WITH 0DB INPUT GAIN (+8DBU WITH 12DB GAIN)
>75DB AT 1KHZ
EQUIV. INPUT NOISE (EIN):
<–128DBU TYPICAL WITH 150 OHMS SOURCE
OUTPUTS UP TO 20 ANALOG; ELECTRONICALLY BALANCED ON PHOENIX/COMBICON REMOVABLE SCREW CONNECTORS
MAXIMUM OUTPUT LEVEL: +19DBU
FREQUENCY RESPONSE:
THD:
20HZ TO 20KHZ (+0.5/–1DB)
<0.01% (20HZ TO 20KHZ, +10DBU OUTPUT)
108DB TYPICAL (22HZ TO 22KHZ UNWEIGHTED)
<–75DB
DYNAMIC RANGE:
CROSSTALK:
CONTROL NETWORK
COBRANET:
RJ45 CONNECTOR (SDEC-4000P, SDEC-4000X)
100M/300 FT. BETWEEN DEVICE AND ETHERNET SWITCH
2 X RJ45 CONNECTORS
MAXIMUM CABLE LENGTH:
ETHERNET:
MAXIMUM CABLE LENGTH:
PANEL LED INDICATORS:
100M/300 FT. BETWEEN DEVICE AND ETHERNET SWITCH
SIGNAL PRESENT (PER INPUT), CLIP (PER INPUT), SYNC/48V (PER INPUT),
LCD, CONDUCTOR ACTIVE, NET LINK ACTIVE, DATA ACTIVITY
MAINS VOLTAGE:
85-270V AC, 50/60HZ
<35VA
POWER CONSUMPTION:
GENERAL
SDEC-3000
SDEC-4000
DIMENSIONS (H X W X D):
1-3/4" X 19" X 9-1/4" (44MM X 483MM X 235MM)
6.5 LB (3KG)
3-1/2" X 19" X 9-1/4" (89MM X 483MM X 235MM)
13 LB (6KG)
WEIGHT:
All features and specifications are subject to change without notice.
JBL, JBL Synthesis and Synthesis are trademarks of Harman International Industries, Incorporated, registered in the United States and/or other countries.
London Architect is a trademark of Harman International Industries, Incorporated.
THX Ultra2 is a trademark of THX Ltd. All rights reserved.
CobraNet is a registered trademark of Peak Audio, a division of Cirrus Logic, Inc.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Declaration of Conformity
We, Harman Consumer Group International
2, route de Tours
72500 Château du Loir
France
declare in own responsibility that the products
described in this owner’s manual are in compliance
with technical standards:
Harman Consumer Group, Inc.
250 Crossways Park Drive
Woodbury, NY 11797
EN 61000-6-3:2001
EN 61000-6-1:2001
8500 Balboa Boulevard
Northridge, CA 91329
818.830.8757
Luc Guillaume
Harman Consumer Group International
Château du Loir, France 10/06
Part No. SDEC3000/4000 OM 10/06
Download from Www.Somanuals.com. All Manuals Search And Download.
|