®
JBl Procoustics Ms-2
car audio optimizer
owner’s Manual
BoX contents
In
Pwr
Sub
DEFEAT
6-ft (1.8m) Audio Cable
TREBLE
IMPACT
BASS
–3
0
+3
+6
+6
On
0
0
+3
+3
IntroductIon
IMAGE
Off
Thank you for your purchase of the JBL® ProCoustics MS-2 car audio optimizer.
We have designed the MS-2 to dramatically improve the sound of portable
audio devices in your vehicle, and to be quick and easy to connect, set up
and use.
3-ft (0.9m) Audio Cable
SETUP
OK
High
Low
This owner’s manual contains all the information you need to set up, connect
and adjust your new car audio optimizer. For more information, go to our Web
JBL ProCoustics MS-2
Car Audio Optimizer
6V Power Supply
Download from Www.Somanuals.com. All Manuals Search And Download.
Impact control and indicators: Press the Impact control to add midbass
punch to the sound (such as the fullness of drums or the upper frequencies
of a bass guitar). The impact setting may also affect the sound of male
vocals. The indicators show the setting.
controls and IndIcators
Input Indicator
Power Indicator
Sub Indicator
Defeat Button
Bass control and indicators: Press the Bass control to boost the bass
(such as low-frequency sounds from bass guitar and bass drum). Two levels
of bass boost are available. The indicators show the setting.
Treble Control
Impact Control
Bass Control
Treble Indicators
Impact Indicators
Bass Indicators
Image control and indicators: For music to be accurately reproduced
and seem as though it comes from musicians spread out across the
dashboard instead of from only the speaker nearest you, the sound from the
left and right speakers must arrive at your ears at exactly the same time. To
achieve this, the MS-2 includes digital time correction (enabled in the Image
control’s “On” setting). If your car’s audio system already includes “DSP”
or surround sound processing, you should set the MS-2’s Image control
to “Off,” but you can choose the setting that sounds best to you. The
indicators show the setting.
Image Control
Setup Button
Image Indicators
Setup Indicators
defeat button: The Defeat button turns off all of the MS-2’s EQ,
processing and user settings, passing audio unchanged to the output. This
lets you compare the sound with and without the MS-2’s processing. When
Defeat is active, the Treble, Impact, Bass and Image indicators all turn off.
Power indicator: Lights green when the MS-2 is on; pulses red when
the MS-2 is in Standby mode. See Standby and On Modes, on page 5, for
more information.
Input indicator: Lights green when audio connectors are inserted and the
input signal level is OK; lights red when the output level of the connected
portable media player is too high. See Setup and Use, on this page, for
more information.
setuP and use
Until you perform a setup procedure, your MS-2 will pass the audio signal
unchanged from the connected device to your vehicle’s audio system. None
of the MS-2’s controls or processing will be active until you perform a setup
procedure.
sub indicator: Lights green when you have set up the MS-2 for use in a
system with a subwoofer. See Using the MS-2 with a Powered Subwoofer,
on page 5.
NOTE: If you have added a subwoofer to your system, please see
Using the MS-2 with a Powered Subwoofer, on page 5, before
performing a setup procedure.
treble control and indicators: Press the Treble control to increase
or decrease the level of the treble (such as high frequency sounds from
cymbals or the sound of the letter “S”). The indicators show the setting.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
DISTRACTION WARNING: Do NOT perform the setup procedure while
driving. We recommend that you perform these functions only after
pulling off the road into a position that you are absolutely sure presents
no risk. Always obey all traffic laws while driving.
6" – 8"
(150mm – 200mm)
setup Procedure:
1. Connect the MS-2 as shown in the Connections section on page 2.
2. Enable your vehicle audio system’s “Aux” (or MP3) input.
3. Set your portable audio player’s volume level to 3/4 full or higher and play
music on it. The MS-2’s input indicator should light green. If the input
indicator flashes red, turn the volume of your portable player down until
the red light stops flashing and remember the setting. This is the volume
control setting you should use on your portable player while using the MS-2.
6. Press and hold the Setup button. The Setup indicators will flash one at
a time and you will hear brief test signals through your audio system’s
speakers. IMPORTANT: Do not move the MS-2 while the test signals
are playing.
7. Keep holding the Setup button until one of the three Setup indicators
remains lit, showing the setup results:
Set player
Input LED flashes.
volume at 3/4.
• OK: Setup has been completed successfully.
The MS-2’s DSP equalization and time
correction processing is now active.
• High: Your vehicle audio system’s volume
control was set too high during the setup
procedure. Lower the system’s volume and
repeat steps 5 – 7.
• Low: Your vehicle audio system’s volume
control was set too low during the setup
procedure. Raise the system’s volume and
repeat steps 5 – 7.
Press-
and-hold
Setup
Setup
LEDs
flash
4. Adjust your vehicle audio system’s volume control so the music is playing
at a comfortable volume level. Adjust the front/rear fader control so that
the sound comes mostly from the front speakers but so you can still hear
some sound from the back. You can readjust this after setup.
button
You can repeat the setup procedure at any time. For example, if you want to
re-tune the system for a different listening position, simply repeat steps 5 – 7
while sitting in the new location. If you want to use the MS-2 in a different
vehicle, you will need to repeat the entire setup procedure (steps 1 – 7).
5. As you sit in your vehicle’s driver’s seat, hold the MS-2 directly in front of
your face, about 6 – 8 inches (150mm – 200mm) away.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
using the Ms-2 with a Powered subwoofer:
standby and on Modes
The MS-2 will automatically enter Standby mode whenever no control
buttons have been pressed and an audio signal has not been present for
approximately five minutes. All indicators will be off and the Power indicator
will pulse red. The MS-2 will automatically turn on whenever an audio signal
is present at its input or whenever you press any control button.
1. Press and hold the Bass button for five seconds.
The Sub indicator light will turn on.
Sub LED lights
2. Set your subwoofer’s crossover
(low-pass filter) to 50Hz.
Press-
You should disconnect the MS-2 from the power supply if you will not be
driving the car for a week or more.
and-hold
Bass
button
3. Turn your subwoofer’s volume control
down until you can barely hear that the
subwoofer is playing while you’re seated
in the driver’s position.
setting the system Volume
For the best audio performance, set your portable music player’s volume
to the same level it was during the setup procedure, and use your vehicle
audio system’s volume control to adjust the volume.
Set subwoofer
volume to
barely audible
adjusting the sound
Press the Treble, Impact, Bass and Image buttons to fine-tune the sound to
your personal preference. The indicators next to the buttons will show the
settings.
Set subwoofer
low-pass crossover
to 50Hz
setting Memory
The MS-2’s settings are stored in flash memory, and will remain
indefinitely when the MS-2’s power connection is removed.
4. Perform the MS-2’s setup procedure as directed on page 4.
sPecIFIcatIons
5. When the setup procedure is completed, readjust your subwoofer’s
volume control to suit your preference. Then, use the MS-2’s adjustments
to further fine tune the sound.
Maximum input voltage:
Power requirement:
1.3V
6V DC, 1A
Dimensions (H x W x D):
9" x 5-7/8" x 2-3/8"
(230mm x 150mm x 60mm)
If you want to perform a setup procedure again, follow the steps above again
before doing so.
Weight:
0.2 lb (96g)
If you want to use the MS-2 in another system that doesn’t include a powered
subwoofer, press and hold the MS-2’s Bass button for five seconds to return
it to normal operation. The Sub indicator light will turn off.
Features, specifications and appearance are subject to change without notice.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
This device complies with Part 15 of the FCC rules and RSS-210 of Canada.
Operation is subject to the following two conditions: (1) This device may not cause harmful interference; and
(2) this device must accept any interference received, including interference that may cause undesired operation.
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radiofrequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
interference to radio or television reception, which can be determined by turning the equipment off and then on,
the user is encouraged to try to correct the interference by one or more of the following measures:
•• Reorient or relocate the receiving antenna.
•• Increase the separation between the equipment and the receiver.
•• Connect the equipment to a different outlet so that the equipment and receiver are on different branch circuits.
•• Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian RSS-210.
Cet appariel numérique de la classe B est conforme à la norme RSS-210 du Canada.
HARMAN Consumer, Inc.
8500 Balboa Boulevard, Northridge, CA 91329 USA
© 2011 HARMAN International Industries, Incorporated. All rights reserved.
JBL is a trademark of HARMAN International Industries, Incorporated, registered
in the United States and/or other countries.
Download from Www.Somanuals.com. All Manuals Search And Download.
|