Washer Replacement Kit for Reliant Scale RSC600
Assembly,Installation and Operating Instructions
3. Remove the nut from the shoulder bolt.
SAVE THESE INSTRUCTIONS
4. Position the shoulder bolt so the head is flush
with the outside of the boom mounting bracket.
NOTE: Check all parts for shipping damage before us-
ing. In case of damage, DO NOT use the equipment.
Contact the Dealer/Carrier for further instructions.
5. Install the nut until it is tight against the shaft of
the shoulder bolt.
SAFETY SUMMARY
6. Repeat STEPS 1-2.
GENERAL WARNINGS
DO NOT insta ll or use this e quipme nt without first
re a ding a nd unde rsta nding the se instruc tions. If
you a re una ble to understa nd the Wa rnings, Ca u-
tions or Instruc tions, c onta c t a he a lthc a re profe s-
siona l, de a le r or te c hnic a l pe rsonne l be fore a t-
te mpting to insta ll this e quipme nt - othe rwise , in-
jury or da ma ge ma y oc c ur.
Proper Washer Installation
1. Examine the washers on the inside of the boom
mounting bracket to see if the washers are binding
against the corners of the boom mounting bracket.
2. Spin the washers on the inside of the boom mount-
ing bracket to see if the washers spin freely.
The we ight c a pa c ity is limite d to the lowe st ra te d
c a pa c ity of a ny one (1) of the c ompone nts in
use (i.e . Pa tie nt Lift, Sling or Sc a le ). The pa tie nt's
we ight MUST NOT e xc e e d the lowe st ra te d c a -
pa c ity of a ny c ompone nt.
3. If the washers ARE binding against the corners of
the boom mounting bracket and/or DO NOT spin
freely, the washers MUST be replaced. Refer to
REPLACING WASHERS in this instruction sheet.
INSTALLATION WARNINGS
Afte r ANY a djustme nts, re pa ir or se rvic e a nd
BEFORE use , ma ke sure a ll a tta c hing ha rdwa re
is tighte ne d se c ure ly.
REPLACING WASHERS (FIGURE 1)
NOTE: Refer to the INSTALLATION WARNINGS in
the SAFETY SUMMARY of this instruction sheet.
Pa tie nt a nd sling MUST be re move d from the lift
during ALL insta lla tion proc e dure s.
1. Remove the nut, shoulder bolt and two (2) exist-
ing large washers securing the load cell assem-
bly to the boom mounting bracket.
This kit contains the following:
DESCRIPTION
QTY
2. Position the load cell assembly into the boom mount-
ing bracket, with the scale facing the direction shown
in FIGURE 1.
Washers
2
CHECKING FOR PROPER SCALE
INSTALLATIONN (FIGURE 1)
NOTE: Refer to the INSTALLATION WARNINGS in
the SAFETY SUMMARY of this instruction sheet.
NOTE: The end of the scale with the Invacare logo
should be towards the inside of the lift.
3. Perform one (1) of the following:
A. ALL RELIANT MODEL LIFTS - Position one
(1) NEW large washer on each side of the load
cellassembly, insidetheboommountingbracket.
Proper Shoulder Screw Installation
1. Examine shoulder bolt and nut securing the load
cell assembly to the boom mounting bracket. Look
for the following conditions:
B. MODEL 9805 LIFTS - Proceed to STEP 4.
4. Align the mounting holes in the load cell assembly,
NEW large washers (if applicable) and the boom
mounting bracket.
A. The shoulder bolt head should be flush against
the outside of the boom mounting bracket.
B. The nut should be tight against the shoulder bolt
shaft.
5. Secure the load cell assembly with washers (if appli-
cable) to the boom mounting bracket with the shoul-
der bolt and nut. Perform the following steps:
C. The shoulder bolt with the nut installed should turn
freely in the load cell assembly mounting holes.
A. Insert the shoulder bolt through the boom
mounting bracket, large washers (if applicable)
and load cell assembly so the head is flush
with the outside of the boom mounting bracket.
2. Perform one (1) of the following:
A. ANY CONDITIONS FROM STEP 1 ARE NOT
MET - Proceed to STEP 3.
B. Install the nut until it is tight against the shaft
of the shoulder bolt.
B. ALL CONDITIONS FROM STEP 1 ARE MET
- Proceed to PROPER WASHER INSTALLA-
TION in this instruction sheet.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
|