SUMMER RAIN™ II
2 PERSON SHOWER SYSTEM
ONE WALL
INSTALLATION AND OPERATING INSTRUCTIONS
Jacuzzi Whirlpool Bath© BY82000 03/05
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Specifications _________________________________________________________________________ 2
Enclosure Specifications ________________________________________________________________ 3
Rough-in Reference ____________________________________________________________________ 3
Component Identification ________________________________________________________________ 4
Base Installation _______________________________________________________________________ 5-7
Tower and Doors Installation _____________________________________________________________ 8-15
Operation ___________________________________________________________________________ 16-17
Maintenance __________________________________________________________________________ 18
Tower Fixture Repair Parts _______________________________________________________________ 19
Tower Plumbing Repair Parts _____________________________________________________________ 20
Warranty ____________________________________________________________________________ 23-24
Save These Instructions for Future Use.
Owner's Record
Date Purchased ____________________________________________________________
Purchased From ____________________________________________________________
Installed By ________________________________________________________________
Serial Number _____________________________________________________________
Model ____________________________________________________________________
1
Jacuzzi Whirlpool Bath© BY82000 03/05
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Important: Read complete instructions before beginning installation.
Each unit arrives ready for installation, equipped with base, glass and associated hardware.
Remove the unit from the carton. Retain the shipping carton until satisfactory inspection of the product has been
made.
Immediately upon receipt, inspect the base and other components before installing. Check all carton inserts for
partsandhardware. Shouldinspectionrevealanydamageordefectinanycomponent, donotinstalltheunit. Damage
or defect to any component claimed after the unit is installed is excluded from the warranty. Jacuzzi Whirlpool Bath's
responsibility for shipping damage ceases upon delivery of the products in good order to the carrier. Refer any claims
for damage to the carrier. For definitions of warranty coverage and limitations, refer to the published warranty
information packed with the product.
Jacuzzi Whirlpool Bath© is not responsible for any defect that could have been discovered, repaired, or avoided by
following this inspection.
BASE SPECIFICATIONS
DIMENSIONS
72"
27-11/16"
1/2" FLEXIBLE
WATER SUPPLY
HOSES UNDER
48"
BASE
(BOTH SIDES)
AIR SUPPLY HOSE
TOP VIEW
30-1/4"
1-1/2" TILE FLANGE
21-1/16"
18-11/16"
27-1/4"
6-1/2"
4-1/2"
FRONT VIEW
PRODUCT WEIGHT (Base and Enclosure )
TOTAL WEIGHT/FLOOR LOADING
950 lb
(431 kg)
1266.6 lb
63.3 lb/sq. ft.
(574.5 kg)
(332.1 kg/m2)
NOTE: MINIMUM WATER PRESSURE FOR THE SYSTEM IS 45 PSI WITH 3/4" HOT & COLD SUPPLY SERVICE.
2
Jacuzzi Whirlpool Bath© BY82000 03/05
Download from Www.Somanuals.com. All Manuals Search And Download.
ENCLOSURE SPECIFICATIONS
84"
72"
48"
FRONT VIEW
SIDE VIEW
ROUGH-IN REFERENCE
72"
BLOWER MOTOR FOR
UNITS WITH AIR
1" TILE FLANGE
38-15/16"
27-11/16"
48"
AIR LINE FOR
UNITS WITH AIR
36"
TOP VIEW
3
Jacuzzi Whirlpool Bath© BY82000 03/05
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPONENT IDENTIFICATION
SIDE SUPPORT RAIL
GLASS SIDE PANEL
CENTER SUPPORT RAIL
WATER TOWER
AIR TOWER
DOOR POST
WATER TOWER
DOOR POST
RAIL BRACKET
AND COVER CAP
WALL POST
SEAT
GLASS SIDE PANEL
GLASS DOORS
BASE
FRONT VIEW
SIDE VIEW
WALL POST
WALL POST
GLASS SIDE PANEL
GLASS SIDE PANEL
SEAT
BASE
WATER TOWER
WATER TOWER
DOOR POST
AIR TOWER
DRAIN
DOOR POST
GLASS DOORS
(SUPPORT AND SIDE SUPPORT RAILS NOT SHOWN)
4
Jacuzzi Whirlpool Bath© BY82000 03/05
Download from Www.Somanuals.com. All Manuals Search And Download.
BASE INSTALLATION
PRELIMINARY ROUGH-IN
INSTALLATION INSTRUCTIONS
Thefloorstructurebeneaththeunitmustbeableto
support a total weight of the unit and bather. Refer
to page 2, SPECIFICATIONS, for weight specifica-
tions . Refer to COMPONENT IDENTIFICATION on
page 4 to help identify parts.
STEP 2
Remove the stainless steel strainer from the drain
assembly. Disassemble the locknut and two gaskets
from the back of the drain assembly. Apply a 1/4" bead
ofcaulking(silicone)tothedrainholeandinsertthedrain
assembly. Replace the rubber washer, fiber washer,
and lock nut in that order. Hand tighten the locknut.
Remove excess sealant from finished side.
Apply a lubricant (common household liquid soap
works well) to the inside of the rubber seal of the drain
assembly.
STEP 1
Provide an opening in the subfloor no less than 5" x 5"
square. This opening should be located on the center
lines of the shower base drain hole.
STRAINER
APPLY LUBRICANT
SILICONE
SEALANT
DRAIN
ASSEMBLY
C
L
SHOWER BASE
C
L
RUBBER WASHER
2" WASTE PIPE
5"X5" OPENING
(MIN. AS POSSIBLE)
NUT
FIBER WASHER
CAUTION: A nonflammable protective barrier must
be placed between soldering work and base unit to
prevent damage to the base.
STEP 3
If the subfloor is level, no other preparation is neces-
sary. You can proceed to install the shower base. If the
subfloor is not level, level the subfloor by spreading floor
leveling compound, mortar, plaster or minimal expan-
sion structural foam with a minimum density of 5 lbs./
cubic feet EVENLY over ENTIRE area where base will
be installed. The compound used MUST make contact
with the entire bottom surface of the base. Both sides
of a joint or splice of subfloor should be level to each
other. Level and support waste pipe cutout area greater
than 5" x 5". The base is NOT to be supported by the tile
flange.
STUD
WALL
COPPER FITTINGS
AND TUBING
NOT PROVIDED
45° COPPER ELBOW
PROVIDED (2)
DETAIL 1
SPREAD MORTOR OR LEVELING
COMPOUND ETC EVENLY OVER ENTIRE AREA
5
Jacuzzi Whirlpool Bath© BY82000 03/05
Download from Www.Somanuals.com. All Manuals Search And Download.
BASE INSTALLATION
STEP 4
STEP 5
Before installing the base, make sure the 4 water
supply hoses are routed to seat area. If you have a with
Air unit also route the air supply hose to the seat area.
If you have a with Air unit also pull the 2 flow switch
cables and the control panel cable through base at this
time.
Before installing the seat frame, apply silicone sealant
around mating flange on base. Lower seat frame onto
flangeandbase. Attachtheseatframeflangetothestud
wall and blocking with self-drilling screws (included).
Useaminimumof3screwsperflangesection. Cleanup
any excess sealant.
With the drain fitting passing over the center of the
drainpipe, lower the shower base carefully into place,
push down firmly until the base is in place.
BLOCKING
You must check the level of the base in two directions.
Do not lift a corner of the shower base to level the base.
This will cause a loss of contact with the mortar and void
yourwarranty. Attachtheshowerbaseflangetothestud
wall and blocking with self-drilling screws (included).
Use a minimum of 3 screws per flange section.
SEAT
FRAME
APPLY
SEALANT
ON
FLANGE
LOWER SEAT FRAME OVER
FLANGE ON BASE
NOTE: If there is any gap between seat frame flange
and stud or blocking, shims MUST be used to pre-
vent distortion or cracking of the flange. See Shim
Instructions.
FLOW
SWITCH
CABLE*
(2X)
CONTROL
PANEL
CABLE*
POSITION BASE OVER CENTER OF
DRAIN PIPE AND SET INTO PLACE
STEP 6
With a large screwdriver and the tool included with the
drain, tighten the inside compression nut to seal the
drain pipe connection. After drain is fully installed, test
for proper drainage. If the shower base does not drain
properly, rectify this condition before proceeding with
the installation. Jacuzzi Whirlpool Bath© is not re-
sponsible for removal and/ or reinstallation costs.
* ONLY WITH AIR TOWER UNITS
NOTE: If there is any gap between base flange and
stud or blocking, shims MUST be used to prevent
distortion or cracking of the flange. See Shim In-
structions.
TIGHTEN SEALING NUT
SHIM INSTRUCTIONS
TOOL
(INCLUDED)
TILE
FLANGE
SHIM
NOTE: Watertight installation of the drain is the
installer’s responsibility. Drain leakage is excluded
from the Jacuzzi Whirlpool Bath© warranty.
Replace the strainer and tape over the drain hole to
prevent finishing material from entering drain.
TILE
FLANGE
GAP
USE
SCREWS
(PROVIDED)
USE
SCREWS
(PROVIDED)
STUD
STUD
INCORRECT
CORRECT
6
Jacuzzi Whirlpool Bath© BY82000 03/05
Download from Www.Somanuals.com. All Manuals Search And Download.
BASE INSTALLATION
STEP 7
STEP 8
Place cement board or equivalent on top of shower
base flange and secure to studwall.
Filling the area marked DO NOT FILL will prevent
moisture from properly draining back into the base
through weep holes. This moisture is due to leakage
through the tile grout. Sealing the tile grout will reduce
or prevent this leakage.
Applytile(orotherfinishingmaterial)leavinga1/8"gap
between the finishing material and the shower base
flange lip. Seal this gap with silicone sealant. Leave a
minimum 1/4" gap at the back and front corners of the
shower base to allow drainage from leakage through
unsealed tiled grout.
TILE
CEMENT
BOARD
GROUT
STUD
TILE
STUD
CEMENT
BOARD
TILE
ADHESIVE
SILICONE
SEALANT
CAULKING
FLANGE
SHIM IF NECESSARY
STUD
DO NOT FILL
SHIM IF
NECESSARY
1-1/8" MAXIMUM
NO MINIMUM
1/8" GAP
TO FILL GAPS
BETWEEN
BETWEEN STUD
BASE &
TILE
DO NOT FILL
THIS AREA
AND FLANGE
STEP 9
NOTE: ALLOW 24 HOURS DRYING TIME BEFORE
BEGINNING THE TOWER AND DOOR INSTALLA-
TION.
ATTACH WITH
SCREWS PROVIDED
See Shim Instructions on page 6.
CLEAN UP AFTER BASE INSTALLATION
To avoid dulling and scratching the acrylic surface of the base, never use abrasive cleaners. A mild liquid detergent
and warm water clean soiled surfaces.
Remove spilled plaster with a wood or plastic edge. Metal tools scratch the surface. Spots left by plaster or grout
can be removed if lightly rubbed with detergent on a damp cloth or sponge.
Paint, tar, or other difficult stains can be removed with paint thinner, turpentine, or isopropyl alcohol (rubbing
alcohol).
Minor scratches which do not penetrate the color finish can be removed by lightly sanding with 600-grit wet/dry
sandpaper. You can restore the glossy finish to the acrylic surface of the base with a special compound, Meguiar’s
#10 Mirror Glaze. If not available, use automotive rubbing compound followed by an application of automotive paste
wax.
Major scratches and gouges which penetrate the acrylic surface require refinishing. See your Jacuzzi Whirlpool
Bath© dealer for special instructions.
7
Jacuzzi Whirlpool Bath© BY82000 03/05
Download from Www.Somanuals.com. All Manuals Search And Download.
TOWERS AND DOORS INSTALLATION
THESE INSTRUCTIONS ARE FOR SUMMER RAIN
UNITS WITH AND WITHOUT AIR FEATURE OPTION.
REFERTOCOMPONENTIDENTIFICATIONONPAGE
4 TO HELP IDENTIFY PARTS.
WATER TOWER DETAIL
FLOW
SWITCH
CABLE*
All wall finish tiling, trim, and sealing should be
completed before beginning this part of the installa-
tion.
BOLT (5/16")
WASHER
STEP 1
Position each tower on mounting pad on base. For the
shower towers, feed hot and cold supply line through
appropriate holes in bottom of tower. For air feature,
feed air line through large hole on bottom cap of the air
tower. Checkwithalevelwhenattachingtowerstobase.
Tightentowerbaseboltsafterleveling(1boltpershower
tower and 2 bolts for air tower).
SHOWER
TOWER (2X)
COLD
HOT
* ONLY WITH AIR TOWER UNITS
STEP 2 (WITH AIR FEATURE ONLY)
Route control panel cable up through air tower and
connect to control panel.
CONTROL
PANEL CABLE
BOLT 5/16" (2)
WASHER (2)
AIR
TOWER
AIR SUPPY PIPE
BLACK LEAD
REAR OF CONTROLLER
STEP 3 (WITH AIR FEATURE ONLY)
Route flow switch cables up through water towers and
connect to flow switch on both shower towers.
FLOW
SWITCH
FROM
CONTROL
BOX
8
Jacuzzi Whirlpool Bath© BY82000 03/05
Download from Www.Somanuals.com. All Manuals Search And Download.
TOWERS AND DOORS INSTALLATION
STEP 4
Take the side support rails and install a cover cap and wall bracket on each end. Place the center support rail into slot
on each tower. If rail does not readily fit into slots, it may be necessary to loosen the bolts holding towers to base (it
may only be necessary to loosen one tower). DO NOT FORCE CENTER RAIL INTO SLOTS. With center support rail
in position, install hold down brackets but do not tighten screws. Place the side support rails into the slot on each water
tower. With side rails in position install hold down brackets, but do not tighten screws. Check side support rails for
level and mark on the finished wall where to attach rail bracket. See DETAIL A. Drill 3/16" holes and secure bracket
with screws and wall anchors provided. Slide cover cap over rail bracket. If a tower bolt was loosened, retighten while
checking the plumb of the tower. Tighten screws on all hold down brackets.
COVER CAP (2)
SIDE SUPPORT RAIL (2)
HOLD DOWN BRACKETS (5)
RAIL BRACKET (2)
CENTER SUPPORT RAIL
WATER TOWER JAMB
WATER TOWER DOOR POST
ATTACH RAIL
BRACKET TO WALL
SECURE RAIL TO
BRACKET (TURN CW
TO TIGHTEN)
SCREW (8 PER WATER TOWER)
(4 PER AIR TOWER)
RAIL HOLD
DOWN BRACKET
(1 PER AIR TOWER)
(2 PER WATER TOWER)
MOVE COVER CAP
OVER BRACKET
DETAIL A
9
Jacuzzi Whirlpool Bath© BY82000 03/05
Download from Www.Somanuals.com. All Manuals Search And Download.
TOWERS AND DOORS INSTALLATION
STEP 5
Two shut-off valves are provided per water tower. To
hook up supply lines, unscrew valves from braided line.
Using thread sealant, screw each valve to stub out at
bottom of tower. Then reconnect braided line using
provided gasket. Do not twist or kink supply lines when
connecting. Perform this step for both water towers.
SHUT OFF
VALVES
(PROVIDED)
HOT
COLD
CAULK AROUND SUPPLY
PIPING AND INSIDE TOWER BASE
STEP 4 (WITH AIR FEATURE ONLY)
Attach air supply pipe to air tower plumbing.
10
Jacuzzi Whirlpool Bath© BY82000 03/05
Download from Www.Somanuals.com. All Manuals Search And Download.
TOWERS AND DOORS INSTALLATION
STEP 6
STEP 7
Move the door assembly to the door post on water tower
and slide the assembly into the door post. Locate the
base of the door into the slot of serrated door positioner
that positions the hinge barrel as shown.
Check that the magnetic mouldings on door and air
tower overlap. Insert adjusting bolt with locking nut into
fixed nut in top cap (See below). Adjust the door with
adjusting screw until the glass is parallel with shower
base and door moulding mates with water tower mould-
ing. It may be necessary to reposition the door into
another slot (See STEP 6) which can be done without
removing door from wall post. To do so remove the
adjusting screw from wall post, lift the door slightly to
reposition. Reinsertadjustingscrewandlockingnutand
adjust glass door. After final adjustment, lock this posi-
tion with locking nut. Repeat for other door.
WATER
TOWER
GLASS DOOR
BOTTOM OF
DOOR FRAME
DOOR POST
ADJUSTING
SCREW (12mm)
SHOWER BASE
HINGE BARREL
LOCKING
NUT
HINGE
BARREL
STEP 8
Install cover cap by sliding over adjusting screw and
bracket.
COVER CAP
11
Jacuzzi Whirlpool Bath© BY82000 03/05
Download from Www.Somanuals.com. All Manuals Search And Download.
TOWERS AND DOORS INSTALLATION
STEP 9
STEP 11
Position the fixed glass wall post so that the glass side
panel will be parallel with the outside edge of the base.
The fixed glass wall post position may vary slightly due
to the anchored location of the water tower.
Slide fixed glass panel all the way into wall post.
FINISH WALL
GLASS SIDE
PANEL MOUNTED
PARALLEL TO
EDGE OF BASE
EDGE
OF BASE
STEP 10
Level the post in its proper position and mark where
screwholesaretobedrilled. Drill3/16"holesandsecure
with wall anchors and screws provided. Apply tape
(provided) firmly over screw heads.
WALL POST
TAPE (3)
SCREWS (3)
12
Jacuzzi Whirlpool Bath© BY82000 03/05
Download from Www.Somanuals.com. All Manuals Search And Download.
TOWER AND DOOR INSTALLATION
STEP 13
STEP 12
Installglazinggasketonfixedglasswallspostandjambs
on the outside. Note orientation of gasket. Soapy water
may help to insert the glazing gasket.
Align the glass with glass jamb and insert. Repeat
STEPS 8 through STEP 10 for the other fixed glass
panel.
NOTE: The glazing is to be installed on the outside of
enclosure for both wall posts and tower jambs.
Clean any soapy residue off the glass and towers. On
the inside of enclosure, apply sealant to entire length
of glass and wall post as well as the entire length of
the glass and tower jamb.
GLASS
INSIDE OF
WALL POST
ENCLOSURE
GLAZING GASKET
APPLY SEALANT
GLASS
APPLY SEALANT
GLAZING GASKET
INSIDE OF
ENCLOSURE
JAMB
13
Jacuzzi Whirlpool Bath© BY82000 03/05
Download from Www.Somanuals.com. All Manuals Search And Download.
TOWERS AND DOOR INSTALLATION
STEP 16
STEP 14
Install handles as shown. Note orientation of handle.
Hand tighten knob. Flat screw has a screw driver notch.
Do not over tighten either knob or flat screw as cracked
glass may result.
Install fixed glass cover cap on wall post.
COVER CAP
INTERIOR OF
SHOWER
LARGE
WASHER
GLASS
DOOR
WASHERS
DOOR
HINGE
STEP 15
Install all towers' top cover
STEP 17
Turn on water supply and check for leaks. Correct any
leaks before continuing the installation.
SCREWS
(2 PER TOWER
STEP 18
TOWER
TOP COVER
Install all tower cover panels as shown. Align left side of
tower cover panel with inside seat in each tower. Begin
each panel's snap in at the top of the tower.
TOWER TOP PLATE
TOWER COVER
INSERT THIS SIDE FIRST
TOWER COVER
14
Jacuzzi Whirlpool Bath© BY82000 03/05
Download from Www.Somanuals.com. All Manuals Search And Download.
TOWERS AND DOOR INSTALLATION
STEP 19
Seal all around all bases of towers with sealant. Also seal the inside of both wall posts, jambs, door posts and bottom
of both glass side panels on the inside only.
APPLY SEALANT ALONG BASE AND
SIDE OF WALL POST AND GLASS AND
WALL POST (BOTH SIDES)
APPLY SEALANT
ALONG BASE
OF FIXED GLASS
(BOTH SIDES)
APPLY SEALANT ALONG SIDE OF JAMB
AND DOOR POSTAND JAMB AND GLASS
(BOTH TOWERS)
APPLY SEALANT ALL AROUND
TOWER BASES (ALL 3 BASES)
(RAIL NOT SHOWN)
STEP 20
Remove tape over drain and any other masking or protective covers. Proceed with clean up.
CLEAN UP AFTER TOWERS AND DOOR INSTALLATION
To avoid dulling and scratching the tower surfaces and support rails never use abrasive cleaners. Use a mild liquid
detergent and warm water clean soiled surfaces. Use a mild glass cleaner to clean glass panels and doors.
Paint, tar, or other difficult stains can be removed with normal glass and finish cleaners. Use caution when applying
theseproductstocoatedmetalsurfaces.Testinaninconspicuousplacebeforeusing. Donotuseabrasives,alcohol,
acetone, ammonia or other solvents on any tower component.
Scratches to towers and metal components may not buff or polish out requiring surface refinishing or replacement.
Consult your Jacuzzi Whirlpool Bath© dealer or visit our website at: http://jacuzzi.com/ for a list of authorized finish
contractors.
15
Jacuzzi Whirlpool Bath© BY82000 03/05
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
SHOWER TOWERS
Shower Head
There are three selectable positions: Jet, Normal Pul-
sating, and Aerated flow.
Body Sprays (2 Upper and 2 Lower)
To adjust the flow and intensity, turn as shown. The
spray can also be turned to change the direction of the
spray.
Shower Head
LESS FLOW AND INTENSITY
MORE FLOW AND INTENSITY
Body Sprays
(2 Upper & 2 Lower)
Diverter Control
To turn ON water, turn the inner knob clockwise and
adjust for more or less flow.
The outer knob will divert the water to body sprays,
shower head (position shown), and foot temperature
tester. Water flow is proportional to each function when
outer knob is positioned between main functions. When
outerknobispointingtowhitelineonouterdialface(half
way between main functions) water will be diverted
equally.
Diverter Control
SHOWER
HEAD
STOP RELEASE
Temperature Valve
BODY
SPRAY
FOOT
TEMPERATURE
TESTER
INNER
KNOB
OUTER
KNOB
Temperature Valve
The temperature of the mixed water is adjusted by
means of the graduated handle. This handle has as
safety stop set at 100o F (38oC). To increase the tem-
perature, press the RED button to release the stop and
continue turning the handle.
Foot Temperature Tester
Foot Temperature
Tester
16
Jacuzzi Whirlpool Bath© BY82000 03/05
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
AIR TOWER
Air Jet (12)
Controller
AIR TOWER CONTROLS
ON/OFF
BUTTON
INCREASE
TEMPERATURE
DECREASE
TEMPERATURE
AIR FLOW LED
AIR TEMPERATURE LED
AIR TEMPERATURE
AIR FLOW
CONTROLLER
To turn ON press ON/OFF button or turn ON water at either shower tower.
The unit will then automatically go into a preheat cycle to heat the air
transmission pipes. There will be a 5 (five) minute pause while the system
preheats. During this time both LEDs will be ON. When ready for drying,
press the ON/OFF button. Heat and air flow will rise together (only at initial
start-up). After reaching the desired flow, the temperature may be de-
creased or increased using the Temperature button. The air flow may also
be adjusted.
Note: Temperature and air flow are factory set with a predetermined heat
and air speed.
17
Jacuzzi Whirlpool Bath© BY82000 03/05
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
To remove any lime scale from the shower head and body sprays, rub with your finger the outer ring of nozzles on the
shower head and all nozzles on the body spray.
To clean the foot temperature tester, unscrew the nozzle and back flush the wire mesh filter. Do not use metal tools
(such as scissors or screwdrivers, etc.) to clean the body sprays, shower head or foot temperature tester.
To clean the base, simply use a mild, nonabrasive liquid detergent solution. You can protect and restore the gloss to
a dulled acrylic surface by applying Meguiar's #10 Mirror Glaze, a product specifically designed for use on acrylic
finishes. If Meguiar's is not available, an acrylic polish of equal quality or automotive paste wax is acceptable.
The glass can be cleaned with any glass-cleaning product available on the market.
Do not use abrasives, alcohol, acetone, ammonia or other solvents on any tower component.
The thermostatic valve has 2 screen filters that should be cleaned periodically. To remove the filters turn off hot and
cold supplies. Remove each water tower cover. Disconnect the supply hoses from the valve and remove filter from
the hose. Remove any debris. Reinstallation is the reverse of removal. Turn on hot and cold supply and check for
leaks before replacing tower cover.
18
Jacuzzi Whirlpool Bath© BY82000 03/05
Download from Www.Somanuals.com. All Manuals Search And Download.
TOWER FIXTURES REPAIR PARTS
1 (5X)
2 (5X)
(5X)
3
TOWER ASSEMBLY
4
9 (5X)
10
6
5
11 (4X)
7 (PART OF U547000)
8
12
13
14
15
16
17
PART OF D709827
18
WASHER (PART OF D709827)
1. C546000 Lock Nut, 1/2" NPT WP (5X)
19
2. G559000 Ring Compression SS (5X)
3. G560000 Washer Rubber (5X)
4. U546000 (Part of U547000) Nut Valve Transfer, Chrome
5. U566000 Gasket, 1.41 ID x .063 Thick
6. U547000 Valve, Mixer/Transfer Assembly
7. U550827 (Part of U547000) 567000 Nut, Mixer Valve, Chrome
8. U567000 Gasket, 1.9 ID x .063 Thick
9. G432000 Nipple, 1/2" Close
10. U217827 Shower Head, Chrome
11. U215827 Jet, Wall Body, Chrome
12. U219827 Face Plate, Transfer Valve, Chrome
13. U546827 Nut Transfer Valve, Chrome
14. U545827 Collar, Transfer Valve, Chrome
15. U544000 O-Ring, Transfer Valve
16. U543827 Knob, Flow Control, Chrome
17. U549827 Collar, Mixer Valve, Chrome
18. U548827 Knob, Mixer Valve Chrome
19. D709827 Fill Spout Assembly, Stubby, Chrome
19
Jacuzzi Whirlpool Bath© BY82000 03/05
Download from Www.Somanuals.com. All Manuals Search And Download.
TOWER PLUMBING REPAIR PARTS
ITEM
NO. QTY. PART NO.
DESCRIPTION
1
2
3
4
5
6
7
8
1
3
4
3
2
1
1
1
1
1
2
1
1
1
1
2
2
4
1
Y221000
U401000
Y724000
7164000
0455000
7269000
7269000
U547000
Y723000
7269000
U405000
7269000
7269000
7269000
U137827
U540000
GASKET
U421000
U400000
TOWER, 2 PERSON SHOWER
FTG, ELL, .50" FST x 10 mm BARB
1/2" ELBOW, SLIP x THREAD, SCH 40
ELL, STREET, .50", 90o
1/2" TEE
1/2" PIPE, FLEX 5 1/2" LG
1/2" PIPE, FLEX 5 1/2" LG
VALVE, MIXER/TRANSFER ASSEMBLY
1/2" TEE, S x S x THREAD, SCH 40
1/2' PIPE, FLEX 13.75" LG
TUBING, PVC REINFORCED, 31.00" LG
1/2" PIPE, FLEX 5" LG
1/2" PIPE, FLEX 6" LG
1/2" PIPE, FLEX 8" LG
CAP, BOTTOM, TOWER, CH
1/2" FLEX HOSE, 38", FEMALE SWIVEL HEADS
GASKET SUPPLIED WITH HOSE
WASHER, FTG, .7 OD
9
10
11
12
13
14
15
16
17
18
19
FTG, STRAIGHT, 1/2" FTS x 10 mm BARB
2
18
1
4
5
4
11
7
3
6
18
19
10
14
9
3
18
2
5
4
12
13
8
3
16
11
18
17
2
15
20
Jacuzzi Whirlpool Bath© BY82000 03/05
Download from Www.Somanuals.com. All Manuals Search And Download.
21
Jacuzzi Whirlpool Bath© BY82000 03/05
Download from Www.Somanuals.com. All Manuals Search And Download.
PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
USE INSTALLATION INSTRUCTIONS SUPPLIED WITH PRODUCT.
Jacuzzi Whirlpool Bath© has obtained applicable code (standards) listings generally available on a national basis for products of
this type. It is the responsibility of the installer/owner to determine specific local code compliance prior to installation of the product.
Jacuzzi Whirlpool Bath© makes no representation or warranty regarding, and will not be responsible for any code compliance.
Jacuzzi Whirlpool Bath National Headquarters
P.O. Box 702168, Dallas, TX 75370-2168
Service Support: (800) 288-4002
Jacuzzi Whirlpool Bath© BY82000 03/05
Printed on Recycled Paper
Printed in U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
JacuzziWhirlpoolBathLimitedWarranty
DesignerCollectionShowerProduct
WARRANTY COVERAGE
JacuzziWhirlpoolBath(the“Company”)offersthefollowingexpresslimitedwarrantytotheoriginalpurchaserofanyJacuzziWhirlpoolBathDesigner
CollectionBathProduct(“unit”)whopurchasestheproductforpersonalorsinglefamilyuse(“user”).TheCompanywillrepairorreplace,atitsoption,the
unitoritsequipmentinaccordancewiththefollowingtermsandconditions.
TWO YEAR LIMITED WARRANTY ON BATHS
OurlimitedwarrantyonDesignerCollectionBathproductsisfortwo(2)years.Ourwarrantycoverstheunitandfactory-installedcomponentsagainst
defectsinmaterialorworkmanship.Warrantycoveragebeginsonthedatetheunitwasoriginallypurchasedbytheuser.
NINETY DAY (PARTS ONLY) LIMITED WARRANTY ON OPTIONS AND ACCESSORIES
OurwarrantyonoptionsandaccessoriesmanufacturedbytheCompanyisforninety(90)daysforpartsonly.Ourwarrantycoversoptionsandaccessories
manufacturedbytheCompanyagainstdefectsofmaterialorworkmanship.Warrantycoveragebeginsonthedatetheoptionoraccessorywasoriginallypurchased
bytheuser.
WARRANTY LIMITATIONS
Ourlimitedwarrantydoesnotcoverdefects,damage,orfailurecausedbythecommoncarrier,installer,user,orotherperson,orresultingfrom,without
limitation,anyofthefollowing:carelesshandling(liftingunitbyplumbing,abradingfinish,etc.);modificationofanytypeforanyreason(includingmodification
tomeetlocalcodes);improperinstallation(includinginstallationnotinaccordancewithinstructionsandspecificationsprovidedwiththeunit);connections
suppliedbytheinstalleroftheequipment;impropervoltagesupplyorunauthorizedelectricalmodification;misuse;incorrectoperation,orlackofproperroutine
maintenance;operationoftheunitwithoutspecifiedminimumamountofwateroratinappropriatewatertemperature;useofabrasiveorimpropercleaners;or
actsofGod,suchaslightning,floods,earthquakes,etc.
Inaddition,THECOMPANYWILLNOTBERESPONSIBLEFORINCIDENTALORCONSEQUENTIALDAMAGESorlossesarisingfromanycause
(e.g.,waterdamagetocarpet,ceiling,lossofuse,etc.)includingitsownnegligence;damagesto,respecting,orresultingfrom:platedpartswhenpooland/orspa
chemicalsareusedintheunit; optionalbathequipmentnotmanufacturedbytheCompanybutsuppliedbyDealer,installerortheCompany;theunit'spriorusage
asanoperationaldisplay;ordefectsthatshouldhavebeendiscoveredbeforeinstallation.Thislimitedwarrantydoesnotinclude:labor,transportation,orother
costsincurredintheremovaland/orreinstallationoftheoriginalunitand/orinstallationofareplacementunit;anycostsrelatingtoobtainingaccessforrepair;
orlossofusedamage,includinglossofsales,profitorbusinessadvantageofanykindunderanycircumstances.Bathunitsareexcludedfromanywarrantycoverage
ifanyaddition,deletion,ormodificationofanykindwhatsoeverhasbeenmadetotheunit(ortoanycomponent).
WarrantycoverageisprovidedintheUnitedStatesofAmericaandCanada.
EXCLUSION OF IMPLIED WARRANTIES
IMPLIEDWARRANTIESOFMERCHANTABILITYANDFITNESSFORAPARTICULARPURPOSEAREDISCLAIMEDALTOGETHERORTO
THE FULL EXTENT ALLOWED BY LAW.
NOTICE: Thiswarrantygivesyouspecificlegalrights,andyoumayalsohaveotherrightswhichvaryfromstatetostate.Therearenowarrantiesapplicable
toJacuzziWhirlpoolBathproductsexceptasexpresslystatedhereinorasimpliedbyapplicablestateandfederallaws.TheCompanywillnotberesponsiblefor
anystatementsorrepresentationsmadeinanyformthatgobeyond,arebroaderthanorareinconsistentwithanyauthorizedliteratureorspecificationsfurnished
bytheCompany.
Somestatesdonotallowlimitationsonhowlonganimpliedwarrantylasts,ortheexclusionorlimitationofincidentalorconsequentialdamages,sotheabove
limitationsandexclusionsmaynotapplytoyou.
RETURN OF WARRANTY CARD
TheattachedWarrantyRegistrationCardMUSTbefilledoutbythepurchaserwithinthirty(30)daysfrompurchaseandmailedtoJacuzziWhirlpoolBath
inorderforthiswarrantytobecomeeffective.
Jacuzzi Whirlpool Bath
P.O. Box 702168
Dallas, TX 75370-2168
Download from Www.Somanuals.com. All Manuals Search And Download.
RESPONSIBILITIES OF OTHERS
Inspecting the unit prior to installation is the responsibility of the installer or building contractor who acts on behalf of the user. They are
responsible for ensuring the unit is free of defect or damage. Notices are placed on and in the unit and on the shipping carton advising the installer
of this responsibility. In the event of a problem, the unit must not be installed. The Company is not responsible for failures or damage that could
have been discovered, repaired, or avoided by proper inspection and testing prior to installation.
Damageoccurringintransitistheresponsibilityofthecarrier.TheuserorinstallerMUSTopenthecrateandinspecttheunitfordamagewhenitisdelivered.
Ifdamageisdiscovered,itmustbereportedimmediatelytothesellerandthecarrierinwriting,andaninspectionrequested.Failureofthecarriertorespondshould
bereportedtothesellerandthecarrier.Yourfreightclaimsshouldbefiledpromptlythereafter.
Itistheresponsibilityoftheinstaller,buildingcontractor,orusertoprovideaccessforservice.TheCompanyisnotresponsibleforanycostsrelatingto
obtainingaccessforrepair.Theusershallbearsuchcostsand,ifappropriate,mustseekrecoveryfromtheinstaller.
Damageoccurringtotheunitduringinstallationistheresponsibilityoftheinstallerand/orbuildingcontractoranddamageoccurringthereafteristhe
responsibilityoftheuser.
Failureofanyoptionalequipmentisthesoleresponsibilityoftheequipmentmanufacturer.(OptionsandaccessoriesmanufacturedbytheCompanyare
warrantedforninety(90)daysfromtheoriginaldateofpurchaseforpartsonly.)
TheDistributororDealerisresponsibleforknowinglocalcoderequirementsandnotifyingtheinstallingcontractorand/oruseroftheserequirementsatthe
timeofpurchase.TheCompanyisnotresponsibleforcoststomodifyanyproducttoobtainanycodeapproval,suchascity,county,orstatebuildingcodesin
U.S.A.ormunicipalorprovincialcodesinCanada.
WARRANTY SERVICE
Forthecustomer'sbenefit,theCompanymaintainsalistofindependentservicepersonneltoperformrequiredwarrantyservicerepairs.Suchfirmsarenotagents
orrepresentativesoftheCompanyandcannotbindtheCompanybywordsorconduct.
TheCompanywillprovidethewarrantyservicedescribedabovewhenthefollowingconditionshavebeenmet:thefailureisofthenatureortypecovered
bythewarranty;theuserhasinformedanAuthorizedJacuzziWhirlpoolBathServiceAgentorWarrantyServiceDepartmentRepresentativeofthenatureofthe
problemduringthewarrantyperiod;conclusiveevidence(e.g.,proofofpurchaseorinstallation)isprovidedtotheforegoingbytheuserprovingthatthefailure
occurredorwasdiscoveredwithinthewarrantyperiod;anauthorizedindependentservicepersonorCompanyrepresentativehasbeenpermittedtoinspectthe
unitduringregularbusinesshourswithinareasonabletimeaftertheproblemwasreportedbytheuser.
Inordertoobtainwarrantyservice,consultyourlocaltelephonebookforthelocationofthenearestJacuzziWhirlpoolBathAuthorizedServiceAgent.Describe
theproblemandtheAuthorizedServiceAgentwillinspecttheunitandprovidetherequiredwarrantyservice.
If you are unable to contact a Jacuzzi Whirlpool Bath Authorized Service Agent, call or write:
Jacuzzi Whirlpool Bath
Warranty Service Department
P.O. Box 702168
Dallas, TX 75370-2168
Call: 1-(800) 288-4002
Toobtainwarrantyreplacementforfactory-installedcomponentsforCompanysuppliedoptionsandaccessoriesmanufacturedandsuppliedbytheCompany,
callorwritetheabove.Provideadescriptionoftheproblemandproofofpurchase.Youwillbeinstructedhowtoobtainreplacementsandwheretoreturn,at
yourexpense,thefailedcomponent(s),option(s),oraccessory(ies).
Allreplacementparts,equipment,andrepairsshallassumetheremainingwarrantyperiodofthepart(s)replaced.
TheCompany'swarrantyobligationshallbedischargedupontenderofreplacementorrepair.Thecustomer'srefusaltoacceptthetenderterminatesthe
Company'swarrantyobligation.
Jacuzzi Whirlpool Bath© BY82000 03/05
Download from Www.Somanuals.com. All Manuals Search And Download.
|