Ingersoll Rand Water Pump PH30F XXX XXX C User Manual

OPERATOR’S MANUAL  
PH30F-XXX-XXX-C  
5-28-08  
RELEASED:  
REVISED:  
(REV. 04)  
INCLUDING: OPERATION, INSTALLATION & MAINTENANCE  
11-13-10  
3" DIAPHRAGM PUMP  
2:1 RATIO (METALLIC)  
READ THIS MANUAL CAREFULLY BEFORE INSTALLING,  
OPERATING OR SERVICING THIS EQUIPMENT.  
It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.  
SERVICE KITS  
Refer to Model Description Chart to match the pump mate-  
rial options.  
637441-XX for fluid section repair (see page 4). NOTE: This kit  
also contains several air motor seals which will need to be  
replaced.  
637369 for air section repair (see page 6).  
637374-6 major air valve assembly (see page 7).  
PUMP DATA  
Models. . . . . . . . . . . see Model Description Chart for “-XXX”  
Pump Type. . . . . . . Metallic Air Operated Double Diaphragm  
Material. . . . . . . . . . see Model Description Chart  
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 268 lbs (121.6 kgs)  
Maximum Air Inlet Pressure . . . . . . . 100 p.s.i.g. (6.9 bar)  
Maximum Material Inlet Pressure. . 10 p.s.i.g. (0.69 bar)  
Maximum Outlet Pressure . . . . . . . . . 200 p.s.i.g. (13.8 bar)  
Maximum Flow Rate . . . . . . . . . . . . . . . 150 g.p.m. (567.8 l.p.m.)  
flooded inlet . . . . . . . . . . . 160 g.p.m. (605.6 l.p.m.)  
Displacement / Cycle @ 100 p.s.i.g. 1.4 gal. (5.3 lit.)  
Maximum Particle Size . . . . . . . . . . . . 3/8dia. (9.5 mm)  
Maximum Temperature Limits (diaphragm / ball / seal  
material)  
Figure 1  
MODEL DESCRIPTION CHART  
PH30F - X S S - S X X - C  
E.P.R. / EPDM. . . . . . . . . . . . . . -60° to 280° F (-51° to 138° C)  
Hytrel® . . . . . . . . . . . . . . . . . . . -20° to 150° F (-29° to 66° C)  
Nitrile . . . . . . . . . . . . . . . . . . . . 10° to 180° F (-12° to 82° C)  
Polypropylene . . . . . . . . . . . . 35° to 175° F (2° to 79° C)  
Santoprene®. . . . . . . . . . . . . . -40° to 225° F (-40° to 107° C)  
PTFE. . . . . . . . . . . . . . . . . . . . . . 40° to 225° F (4° to 107° C)  
Viton® . . . . . . . . . . . . . . . . . . . . -40° to 350° F (-40° to 177° C)  
Dimensional Data. . . . . . . . . . . . . . . . . . see page 8  
Air Motor / Air Cap Material  
F - Conductive Polypropylene  
/ Stainless Steel  
Fluid Connection  
A - 3 - 8 N.P.T.F. - 1  
B - Rp 3 (3 - 11 BSP parallel)  
Fluid Cap & Manifold Material  
S - Stainless Steel  
Noise Level @ 70 p.s.i., 50 c.p.m. . . 83.0 db(A)  
c
d
Hardware Material  
Tested with 67263 muffler assembly installed.  
c
d
S - Stainless Steel  
The pump sound pressure levels published here have been updated to  
an Equivalent Continuous Sound Level (LAeq) to meet the intent of ANSI  
S1.13-1971, CAGI-PNEUROP S5.1 using four microphone locations.  
Seat Material  
S - Stainless Steel  
NOTICE: All possible options are shown in the chart, however, certain  
combinations may not be recommended, consult a representative or  
the factory if you have questions concerning availability.  
Ball Material  
A - Santoprene  
C - Hytrel  
T - PTFE  
V - Viton  
Diaphragm Material  
A - Santoprene  
C - Hytrel  
T - PTFE / Santoprene  
Fluid Section Service Kit Selection  
PH30F - ASS - S X X - C  
637441 - X X  
EXAMPLE: Model #PH30F-ASS-SAA-C  
Fluid Section Service Kit # 637441-AA  
Ball  
Diaphragm  
INGERSOLL RAND COMPANY LTD  
209 NORTH MAIN STREET – BRYAN, OHIO 43506  
© 2010  
CCN 15307648  
(800) 276-4658 FAX (800) 266-7016  
y
Download from Www.Somanuals.com. All Manuals Search And Download.  
GENERAL DESCRIPTION  
MAINTENANCE  
The ARO diaphragm pump offers high volume delivery even  
at low air pressure and a broad range of material compatibil-  
ity options are available. Refer to the model and option chart.  
ARO pumps feature stall resistant design, modular air motor  
/ fluid sections.  
Air operated double diaphragm pumps utilize a pressure dif-  
ferential in the air chambers to alternately create suction and  
a positive fluid pressure in the fluid chambers, valve checks  
insure a positive flow of fluid.  
Refer to the part views and descriptions as provided on  
pages 4 through 7 for parts identification and service kit in-  
formation.  
Certain ARO “Smart Parts” are indicated which should be  
available for fast repair and reduction of down time.  
Service kits are divided to service two separate dia-  
phragm pump functions: 1. AIR SECTION, 2. FLUID SEC-  
TION. The Fluid Section is divided further to match typical  
part Material Options.  
y
y
Pump cycling will begin as air pressure is applied and will  
continue to pump and keep up with the demand. It will build  
and maintain line pressure and will stop cycling once maxi-  
mum line pressure is reached (dispensing device closed) and  
will resume pumping as needed.  
Provide a clean work surface to protect sensitive internal  
moving parts from contamination from dirt and foreign  
matter during service disassembly and reassembly.  
Keep good records of service activity and include the  
pump in preventive maintenance program.  
Before disassembling, empty captured material in the  
outlet manifold by turning the pump upside down to  
drain material from the pump.  
y
y
y
AIR AND LUBE REQUIREMENTS  
WARNING EXCESSIVE AIR PRESSURE. Can cause pump  
damage, personal injury or property damage.  
A filter capable of filtering out particles larger than 50  
microns should be used on the air supply. There is no lu-  
brication required other than the “O” ring lubricant which  
is applied during assembly or repair.  
If lubricated air is present, make sure that it is compatible  
with the “O” rings and seals in the air motor section of the  
pump.  
FLUID SECTION DISASSEMBLY  
y
y
1. Remove (61) outlet manifold and (60) inlet manifold.  
2. Remove (22) balls, (19) “O” rings, (21) seats and (76) seat  
plugs.  
3. Remove (15 and 15a) fluid caps.  
4. Remove the (14) cap screw, (6) diaphragm washer, (7) dia-  
phragm, (5) backup washer and (196) cushion.  
NOTE: Do not scratch or mar the surface of (1) diaphragm  
rod.  
OPERATING INSTRUCTIONS  
Always flush the pump with a solvent compatible with  
the material being pumped if the material being pumped  
is subject to “setting up” when not in use for a period of  
time.  
Disconnect the air supply from the pump if it is to be in-  
active for a few hours.  
The outlet material volume is governed not only by the  
air supply, but also by the material supply available at the  
inlet. The material supply tubing should not be too small  
or restrictive. Be sure not to use hose which might col-  
lapse.  
When the diaphragm pump is used in a forced-feed  
(flooded inlet) situation, it is recommended that a “check  
valvebe installed at the air inlet.  
y
FLUID SECTION REASSEMBLY  
SERVICE NOTE: ARO pn 204214-T diaphragm assembly tool is  
recommended for use when reassembling the pump.  
Reassemble in reverse order. Refer to the torque require-  
ments on page 5.  
Clean and inspect all parts. Replace worn or damaged  
parts with new parts as required.  
Lubricate (1) diaphragm rod and (144) “U” cups with Lu-  
briplate® FML-2 grease (94276 grease packet is included  
in service kit).  
Apply 1/4” wide x 1/8” thick (approximately 46” long)  
expandable PTFE Joint Sealant to air cap (item 68 only)  
diaphragm bead groove. Use ONLY 1 wrap of sealant. DO  
NOT overlap seam. Fill seam with heavy duty anearobic  
sealant. Seam to be located between bolt positions 1 and  
3 (refer to “Torque Sequencediagram, page 5).  
Re-check torque settings after the pump has been re-  
started and run a while.  
y
y
y
y
y
y
y
y
Secure the diaphragm pump legs to a suitable surface to  
insure against damage by vibration.  
y
Hytrel® and Viton® are registered trademarks of the DuPont Company Loctite® and 242® are registered trademarks of Henkel Loctite Corporation  
y
y
y
Santoprene® is a registered trademark of Monsanto Company, licensed to Advanced Elastomer Systems, L.P. ARO® is a registered trademark of Ingersoll-Rand Company  
y
y
y
Lubriplate® is a registered trademark of Lubriplate Division (Fiske Brothers Refining Company) 271™ is a trademark of Henkel Loctite Corporation  
y
y
y
PH30F-XXX-XXX-C (en)  
Page 3 of 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PARTS LIST / PH30F-XXX-XXX-C FLUID SECTION  
637441-XX Fluid Section Service Kits include: Balls (see Ball Option, refer to -XXX in chart below), Diaphragms (see Diaphragm Op-  
tion, refer to -XXX in chart below), and items 3, 19, 70, 144, 175 and 196 (listed below) plus items 174 and 94276 Lubriplate FML-2  
grease (page 6).  
c
BALL OPTIONS PH30F-XSS-SXX-C  
MATERIAL CODE  
[B] = Nitrile  
(3-1/4” diameter)  
(3/16” x 5” o.d.)  
“19”  
“22”  


[C] = Carbon Steel  
[Co] = Copper  
[E] = E.P.R.  
[H] = Hytrel  
[Ny] = Nylon  
[Sp] = Santoprene  
[SS] = Stainless Steel  
[T] = PTFE  
-XXX Ball  
Qty [Mtl] “O” Ring  
Qty [Mtl]  
-XAX 94103-A  
-XCX 94103-C  
-XTX 94103-T  
-XVX 94103-V  
(2)  
(2)  
(2)  
(2)  
[Sp] 94115  
(4)  
(4)  
(4)  
(4)  
[E]  
[V]  
[T]  
[V]  
[H] Y327-350  
[T] Y328-350  
[V] Y327-350  
[V] = Viton  
DIAPHRAGM OPTIONS PH30F-XSS-SXX-C  
(1/8” x 1” o.d.)  
“3”  
Service Kit  
“7”  
“8”  




-XX = (Ball)  
-XXX -XX = (Diaphragm)  
Diaphragm  
Qty [Mtl] Diaphragm  
Qty [Mtl] “O” Ring  
Qty [Mtl]  
-XXA 637441-XA  
-XXC 637441-XC  
-XXT 637441-XT  
94091-A  
94091-C  
94090-T  
(2)  
[Sp] - - - - -  
[H] - - - - -  
[T] 94110-A  
- - -  
- - -  
(2)  
- - - Y328-210  
- - - Y327-210  
[Sp] Y328-210  
(2)  
(2)  
(2)  
[T]  
[V]  
[T]  
(2)  
(2)  
COMMON PARTS  
(size)  
(size)  
Item  
Description  
Rod  
Qty Part No.  
(1) 94984  
(2) 96485  
(2) 94803  
(2) Y13-12-T  
(2) Y5-134-T  
(1) 94107  
(1) 96482  
(2) 94113  
(12) 94412-2  
(16) 94991  
(16) 95053  
(2) 94703-2  
(1) 93004  
(1) 94216-1  
(1) 94216-2  
Mtl  
[C]  
Item  
61  
Description  
Qty Part No.  
(1) 94704-1  
(1) 94704-2  
(1) 96483  
Mtl  
[SS]  
[SS]  
[SS]  
[SS]  
[B]  
(PH30F-AXX-XXX-C)  
(PH30F-BXX-XXX-C)  
1
5
6
9
Outlet Manifold  
Backup Washer  
Fluid Side Washer  
[C]  
[SS]  
[SS]  
[SS]  
[SS]  
[SS]  
[SS]  
[SS]  
[SS]  
[SS]  
[SS]  
[Co]  
[SS]  
[SS]  
68 Air Cap  
69 Air Cap  
70 Gasket  
76 Seat Plug  
(13/16” i.d. x 2” o.d. x 5/32”)  
Washer  
(1) 94031-2  
(2) 94100  
(3/4” - 16 x 3-1/4”)  
14 Cap Screw  
cd  
(left side)  
15 Fluid Cap  
15a Fluid Cap  
21 Seat  
(2) 96484  
[SS]  
(right side)  
(1/2” o.d. tube x 1/2 - 14 N.P.T.F. - 1)  
77 Elbow  
(2) 59756-362 - - -  
(1/2” o.d. tube x 24”)  
78 Tube  
126 Pipe Plug  
(1) 94978-(  
)
[Ny]  
[SS]  
[C]  
e
(M12 x 1.75 - 6g x 45 mm)  
(1/4 - 18 N.P.T. x 13/32”)  
26 Screw  
27 Screw  
(2) Y17-51-S  
(4) 94531  
(M12 x 1.75 - 6g x 60 mm)  
(M10 x 1.5 - 6g x 120 mm)  
(3/16" x 1-3/8" o.d.)  
131 Screw  
(M12 x 1.75 - 6h)  
29 Nut  
32 Leg  
144 “U” Cup  
175 “O” Ring  
(2) Y186-51  
(2) Y325-117  
(4) 94098  
[B]  
cd  
cd  
d
(3/32” x 1” o.d.)  
[B]  
(see page 7)  
(0.406" i.d. x 0.031" thick)  
43 Ground Lug  
180 Gasket  
181 Roll Pin  
[Co]  
(PH30F-AXX-XXX-C)  
(5/32” o.d. x 3/4” long)  
Inlet Manifold  
(4) Y178-56-S [SS]  
(2) 94631 [Sp]  
60  
(PH30F-BXX-XXX-C)  
196 Cushion  
c
(1/2” o.d. x 100’)  
Bulk Tubing  
(1) 94978-100 [Ny]  
e
Items included in air motor service kit, see pages 6 and 7.  
d
Page 4 of 8  
PH30F-XXX-XXX-C (en)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PARTS LIST / PH30F-XXX-XXX-C FLUID SECTION  
3
2
1
4
5
7
8
6
FOR THE AIR MO-  
TOR SECTION, SEE  
PAGES 6 & 7.  
61  
26 ꢁꢂ  
Torque Sequence  
22  
21  
77  
68 ꢆ  
181  
19 ꢀ  
175 ꢀ  
70 ꢀ  
144 ꢀ  
70 ꢀ  
1
5
196  
7
6
9
76  
19 ꢀ  
78  
15  
22  
175 ꢀ  
144 ꢀ  
126 ꢅ  
15a  
77  
19 ꢀ  
21  
27 ꢁꢂ  
19 ꢀ  
76  
29  
69  
180  
131 ꢁꢃ  
3 14 ꢁꢄ  
60  
26 ꢁꢂ  
Figure 2  
32  
ASSEMBLY TORQUE REQUIREMENTS  
NOTE: DO NOT OVERTIGHTEN FASTENERS.  
ALL FASTENERS ARE METRIC.  
)
(
(14) Cap screw, 65 - 70 ft lbs (88.1 - 94.9 Nm).  
(26) Manifold screw, 60 - 70 ft lbs (81.4 - 94.9 Nm).  
(27) Fluid cap screw, 60 - 70 ft lbs (81.4 - 94.9 Nm).  
(131) Screw, 35 - 40 ft lbs (47.5 - 54.2 Nm).  
View for PH30F-XXX-XXT-C (PTFE diaphragm)  
configuration only.  
LUBRICATION / SEALANTS  
Apply Lubriplate FML-2 grease to all “O” rings, “U” cups and mating parts.  
Apply Loctite® 262™ to threads at assembly.  
f
g
h
i
j
Apply PTFE tape to threads at assembly.  
Apply Loctite 271™ to threads.  
Apply anti-seize compound to threads and bolt and nut flange heads  
which contact pump case when using stainless steel fasteners.  
Apply 1/4” wide x 1/8” thick (aproximately 46” long) expandable PTFE  
Joint Sealant to air cap (item 68 only) diaphragm bead groove. Use  
ONLY 1 wrap of sealant. DO NOT overlap seam. Fill seam with heavy  
duty anaerobic pipe sealant. Seam to be located between bolt positions  
1 and 3 (refer to “Torque Sequence” diagram).  
k
(Santoprene)  
8
(PTFE)  
7
Lubriplate FML-2 is a white food grade petroleum grease.  
PH30F-XXX-XXX-C (en)  
Page 5 of 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PARTS LIST / PH30F-XXX-XXX-C AIR SECTION  
Indicates parts included in 637369 air section service kit shown below and items 70, 144, 175 and 180 shown on page 4.  
AIR MOTOR PARTS LIST  
d
(size)  
(size)  
Item  
Description  
Qty Part No.  
(1) 95667-1  
(1) 94092  
(4) 95921  
(2) 95846  
(1) 95651  
(2) 94083  
(2) 94084  
(1) 94860  
(1) 94099  
(7) 95931  
(8) 95923  
(1) 95789-2  
(1) 95790  
(1) Y325-32  
(1) 95966  
(1) Y186-50  
(1) 95650  
(1) 95659  
(1) 94026  
(1) 67164  
Mtl  
[GP]  
[D]  
Item  
168 "O” Ring  
169 “U” Cup  
Description  
Qty Part No.  
(2) 94433  
(1) Y240-9  
(1) 94081  
Mtl  
[U]  
[B]  
(3/32” x 5/8” o.d.)  
101 Center Body  
103 Bushing  
(1/8” x 7/8” o.d.)  
(M6 x 1 - 6g x 180 mm)  
105 Screw  
[SS]  
[SS]  
[D]  
170 Piston Sleeve  
[Br]  
(3/32” x 1-1/8” o.d.)  
107 End Plate  
111 Spool  
171 “O” Ring  
172 “O” Ring  
173 “O” Ring  
174 “O” Ring  
(1) Y325-119 [B]  
d
d
(1/16” x 1-1/8” o.d.)  
(1/16” x 1-3/8” o.d.)  
(1/8” x 1/2” o.d.)  
(check valve)  
(1) Y325-22  
(2) Y325-26  
[B]  
[B]  
(0.250” x 2.276” long)  
(1-1/2 - 11-1/2 N.P.T.)  
118 Actuator Pin  
121 Sleeve  
[SS]  
[D]  
d
(2) Y325-202 [B]  
cd  
d
127 90° Street Elbow  
132 Gasket  
[C / I]  
[B]  
176 Diaphragm  
199 Track Gasket  
200 Gasket  
(2) 94102  
(1) 95666  
(1) 95665  
(1) 67213  
[Sp]  
[B]  
d
d
(M6)  
133 Washer  
[SS]  
[SS]  
[GP]  
[P]  
[B]  
d
(M6 x 1 - 6g x 35 mm)  
(includes item 127)  
201 Muffler Kit  
134 Screw  
(1/8” x 1/2” o.d.)  
135 Valve Block  
136 End Cap  
232 “O” Ring  
(2) Y325-202 [B]  
d
233 Adapter Plate  
(1) 95761  
(4) 95924  
[P]  
(1/16” x 2” o.d.)  
(M6 x 1 - 6h)  
137 “O” Ring  
138 “U” Cup  
139 “U” Cup  
[B]  
236 Nut  
[SS]  
d
d
d
(3/16” x 1.792” o.d.)  
(3/16” x 1-1/4” o.d.)  
(1/8” x 5/8” o.d.)  
[B]  
243 “O” Ring  
244 “O” Ring  
(1) Y325-204 [B]  
(1) Y325-208 [B]  
d
d
(1/8” x 7/8” o.d.)  
[B]  
140 Valve Insert  
141 Valve Plate  
166 Track Gasket  
167 Pilot Piston  
(Ck)  
(Ck)  
[B]  
Lubriplate FML-2 Grease  
(1) 94276  
637308  
c d  
Lubriplate Grease packets (10)  
d
d
(includes items 168 and 169)  
[D]  
c
Items included in fluid section service kit, see pages 4 and 5.  
MATERIAL CODE  
kit.  
2. Install new (171 and 172) “Orings. Replace (170) sleeve.  
3. Install new (168) “O” rings and (169) seal - Note the lip di-  
rection. Lubricate and replace (167) pilot piston.  
4. Reassemble remaining parts. Replace (173 and 174) “O”  
rings.  
[B] = Nitrile  
[Br] = Brass  
[C] = Carbon Steel  
[Ck] = Ceramic  
[D] = Acetal  
[I] = Iron  
[P] = Polypropylene  
[Sp] = Santoprene  
[SS] = Stainless Steel  
[U] = Polyurethane  
[GP]= Groundable Polypropylene  
AIR MOTOR SECTION SERVICE  
MAJOR VALVE DISASSEMBLY  
Service is divided into two parts - 1. Pilot Valve, 2. Major  
1. Remove (135) valve block and (233) adapter plate, expos-  
ing (132 and 166) gaskets, (232) “Oring and (176) checks.  
2. Remove (233) adapter plate, releasing (140) valve insert,  
(141) valve plate, (199 and 200) gaskets and (244, 243 and  
232) “Orings.  
3. Remove (136) end cap and (137) “O” ring, releasing (111)  
spool.  
Valve.  
GENERAL REASSEMBLY NOTES:  
Air Motor Section service is continued from Fluid Section  
repair.  
y
Inspect and replace old parts with new parts as neces-  
sary. Look for deep scratches on metallic surfaces, and  
nicks or cuts in “Orings.  
y
Take precautions to prevent cutting “O” rings upon instal-  
lation.  
Lubricate “Orings with Lubriplate FML-2 grease.  
Do not over-tighten fasteners. Refer to torque specifi-  
cation block on view.  
Re-torque fasteners following restart.  
SERVICE TOOLS - To aid in the installation of (168) “O”  
rings onto the (167) pilot piston, use tool # 204130-T,  
available from ARO.  
y
MAJOR VALVE REASSEMBLY  
y
y
1. Install new (138 and 139) “U” cups on (111) spool - LIPS  
MUST FACE EACH OTHER.  
2. Insert (111) spool into (135) valve block.  
3. Install (137) “O” ring on (136) end cap and assemble end  
cap to (135) valve block, securing with (107) end plates  
and (105) screws.  
y
y
4. Install (140) valve insert and (141) valve plate into (135)  
valve block. NOTE: Assemble (140) valve insert with  
“dished” side toward (141) valve plate. Assemble (141)  
valve plate with 2 identification dots toward (199 and  
200) gaskets.  
5. Assemble (244, 243 and 232) “O” rings, (199 and 200) gas-  
kets and (233) adapter plate to (135) valve block.  
6. Assemble (132 and 166) gaskets, (176) checks and (232)  
“Oring to (101) body.  
PILOT VALVE DISASSEMBLY  
1. A light tap on (118) actuator pin should expose the op-  
posite (121) sleeve, (167) pilot piston and other parts.  
2. Remove (170) sleeve. Inspect inner bore of sleeve for  
damage.  
PILOT VALVE REASSEMBLY  
7. Assemble (135) valve block and components to (101)  
body, securing with (134) screws.  
1. Clean and lubricate parts not being replaced from service  
Page 6 of 8  
PH30F-XXX-XXX-C (en)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PARTS LIST / PH30F-XXX-XXX-C AIR SECTION  
118  
173  
169  
168  
PILOT VALVE  
PART GROUP  
172  
171  
170  
174  
121  
167  
173  
121  
118  
140  
141  
199  
244  
243  
132  
166  
107  
105  
174  
103  
101  
135  
133  
134  
43  
Optional 94117 Muffler  
200  
232  
233  
232  
176  
138  
111  
139  
137  
136  
107  
236  
201  
127  
MAJOR VALVE  
Figure 3  
) ASSEMBLY TORQUE REQUIREMENTS (  
NOTE: DO NOT OVERTIGHTEN FASTENERS.  
ALL FASTENERS ARE METRIC.  
(105) Screw, 15 - 20 in. lbs (1.7 - 2.3 Nm).  
(134) Screw, 40 - 50 in. lbs (4.5 - 5.6 Nm).  
LUBRICATION / SEALANTS  
f
j
Apply Lubriplate FML-2 grease to all “O” rings, “U” cups  
and mating parts.  
Apply anti-seize compound to threads and bolt and  
nut flange heads which contact pump case when us-  
ing stainless steel fasteners.  
A replacement Major Valve Service Assembly is available separately, which includes the following:  
637374-6: 105 (4), 107 (2), 111, 132, 135, 136, 137, 138, 139, 140, 141, 166, 176 (2), 199, 200, 232 (2), 233, 236 (4), 243 and 244.  
PH30F-XXX-XXX-C (en)  
Page 7 of 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLE SHOOTING  
Product discharged from exhaust outlet.  
Low output volume, erratic flow or no flow.  
Check for diaphragm rupture.  
Check air supply.  
y
y
y
y
y
y
Check tightness of (14) cap screw.  
Check for plugged outlet hose.  
Check for kinked (restrictive) outlet material hose.  
Check for kinked (restrictive) or collapsed inlet material  
hose.  
Air bubbles in product discharge.  
Check connections of suction plumbing.  
Check “Orings between intake manifold and fluid caps.  
Check tightness of (14) cap screw.  
y
y
y
Check for pump cavitation - suction pipe should be sized  
at least as large as the inlet thread diameter of the pump  
for proper flow if high viscosity fluids are being pumped.  
Suction hose must be a non-collapsing type, capable of  
pulling a high volume.  
Check all joints on the inlet manifolds and suction con-  
nections. These must be air tight.  
y
Motor blows air or stalls.  
Check (176) check valve for damage or wear.  
Check for restrictions in valve / exhaust.  
y
y
y
y
Inspect the pump for solid objects lodged in the dia-  
phragm chamber or the seat area.  
DIMENSIONAL DATA  
Dimensions shown are for reference only, they are displayed in inches and millimeters (mm).  
P - Air Inlet  
R - Material Outlet  
F
A
L
B
G
N
D
K
H
C
J
Q - Exhaust Port  
M
R - Material Inlet  
DIMENSIONS  
A - 23-1/8(587.4 mm)  
B - 30(762.0 mm)  
C - 12-1/32(306.4 mm)  
D - 2-3/4(69.9 mm)  
F
- 15” (381.0 mm)  
K - 9/16” (14.3 mm)  
P - 3/4 - 14 N.P.T.  
Q - 1-1/2 - 11-1/2 N.P.S.M.  
G - 32” (812.8 mm)  
L
- 2-3/4" (69.9 mm)  
H - 10-5/32” (258.0 mm)  
J
M - 22-27/32” (580.2 mm)  
N - 16" (406.4 mm)  
- 11-21/32" (296.1 mm)  
“RInlet / Outlet  
3 - 8 N.P.T.F. - 1  
Rp 3 (3 - 11 BSP parallel)  
PH30F-ASS-SXX-C  
PH30F-BSS-SXX-C  
Figure 4  
PN 97999-1381  
Page 8 of 8  
PH30F-XXX-XXX-C (en)  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Indesit Washer IWC 6105 User Manual
Invacare Wheelchair Arrow User Manual
JBL Portable Speaker EVO1324 User Manual
Jenn Air Convection Oven JMW3430 User Manual
John Deere Compact Loader 319D User Manual
JVC DVD Player SR MV55 User Manual
Kenwood Car Stereo System TM V7A User Manual
Kenwood Coffeemaker CM700 User Manual
Keys Fitness Elliptical Trainer KF E40 User Manual
KitchenAid Washer KAWE678B User Manual