A Loudspeaker With Intelligence
EVOi.324
User’s Guide
Introducing The Next Generation of Installed Sound
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INFORMATION - READ THIS CAREFULLY
This equipment has been tested and found to comply with the following European and international standards for Electromag-
netic Compatibility and Electrical Safety:
Radiated Emmissions (EU): EN55022B (1992)
RF Immunity (EU): IEC801-3 (1994)
Electrostatic Discharge(EU): IEC801-2 (1984)
Fast Transients(EU): IEC801-4 (1988)
Electrical Safety (EU): EN60065 (1994)
Electrical Safety(USA): UL6500/ETL (1996)
Electrical Safety(CAN): CAN/CSA-E65/ETLc (1996)
Before using the apparatus read these instructions, follow all instructions, heed them and keep in a
safe place.
Clean only with a damp cloth. Do not block any of the ventilation openings. Install in accordance with the manufacturer’s
instructions.
Do not defeat the safety purpose of the grounding type plug. A grounding plug has two blades and a third grounding prong. The
third prong is provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for replace-
ment of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at plugs, convenience recepticals and the point where they
exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.
Unplug this apparatus during lightning storms or when not in use for a long time.
WARNING – TO REDUCE THE RISK OF FIRE OR SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR
MOISTURE.
DO NOT REMOVE COVERS, NO USER SERVICABLE PARTS INSIDE, REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
THIS EQUIPMENT MUST BE GROUNDED.
CAUTION
RISK OF ELECTRONIC SHOCK
DO NOT OPEN
ATTENTION
RISQUE DE CHOC ELECTRIQUE
NE PAS ENLEVER
!
DO NOT EXPOSE
TO RAIN OR MOISTURE
NE PAS EXPOSER A
LA PLUIE NI L'HUMIDITE
IT SHOULD NOT BE NECESSARY TO REMOVE ANY PROTECTIVE GROUND OR SIGNAL CABLE SHIELD
CONNECTIONS TO PREVENT GROUND LOOPS. ANY SUCH DISCONNECTIONS ARE OUTSIDE THE
RECOMMENDED PRACTICE OF JBL PROFESSIONAL AND WILL RENDER ANY EMC OR SAFETY
CERTIFICATION VOID.
For continued compliance with international EMC legislation ensure that all input and output cables are wired with the cable
screen connected to Pin 1 of the XLR connectors. The input XLR Pin 1 is connected to the chassis via a low value capacitor,
providing high immunity from ground loops while ensuring good EMC performance.
Download from Www.Somanuals.com. All Manuals Search And Download.
I N T R O D U C T I O N
WELCOME
PACKAGE CONTENTS
Thank you for purchasing an EVOi.324 Intelligent Powered
Loudspeaker. Not only is this the most compact 1300 watt
powered loudspeaker, it is also the world’s first loudspeaker
with built-in intelligence. The integrated digital technology
allows it to manage its own performance and through the
use of the optional EVOi.net Speaker System Controller,
adapt sonically to virtually any environment in which you
place it. The result is an architecturally designed installa-
tion powered loudspeaker system that provides great sound
with minimum stress.
Upon unpacking the EVOi.324 please take note of the
contents as listed below. If you are missing any of the items
listed below, please contact your dealer as soon as possible.
1 x EVOi.324 Speaker System
1 x User’s Guide with Warranty and Tech Note No. 14,
Volume 1
1 x Accessory bag which includes:
1 x AC Cord
1 x Eyebolt Kit (3 x Shoulder Eye Bolts, 3 x Washers)
2 x Small Rubber Feet
1 x Large Rubber Foot
1 x Washer
2
EVOi.324
Download from Www.Somanuals.com. All Manuals Search And Download.
D E S I G N
O V E R V I E W
The EVOi.324 has been designed specifically for fixed
installation applications. EVO is intended to be used where
high quality state-of-the-art sound reinforcement is
required, in venues such as performing arts centers,
worship spaces, educational multi-purpose rooms and other
civic venues.
It has been engineered to provide premium performance
with minimal visual impact. EVOi.324 speakers adapt to
internal décor with a paintable surface and to low ceilings
by offering the same performance in a vertical and
horizontal configuration.
Installation and setup are quick and simple to understand.
This is the fundamental principle of the EVO system,
whereby the majority of problems in system installation
and set-up are eliminated because the most complex
elements have already been designed into the loudspeaker.
3
EVOi.324
Download from Www.Somanuals.com. All Manuals Search And Download.
F E A T U R E S
3
Thermomaster® Vents
EVOi.324 FRONT/TOP
Each respective baffle vent, woofer motor, and basket are
all linked via the same thermal transfer path for maximum
heat dissipation. Taking heat away from the voice coil
effectively reduces power compression. The harder the
system works, the better it cools.
1
1
1
4
2430 Compression Driver
2
3
The JBL 2430 neodymium large-format compression driver
has a 1.5-inch exit and 3-inch voice coil with 100 watt
power handling. The revolutionary neodymium motor
structure results in an extremely compact and lightweight
HF (High Frequency) transducer, weighing only 2.5 lbs.
The JBL 2430 driver is powered by an internal 100 watt
linear amplifier.
3
4
5
5
Aluminum Waveguide
The aluminum waveguide effectively couples the JBL 2430
driver to the outside world. It works with the LF/MF and
LF transducers and our Filtered Array Technology (FAT™)
to achieve a constant 80° x 80° horizontal and vertical
coverage pattern.
3
3
7
2
6
6
Integrated Baffle
Our integrated transducer baffle and inertia grounding
straps are designed to lock all the components together,
maximizing acoustic output. The entire baffle area acts as
an open thermal window through which heat is allowed to
escape.
Figure 1 - EVOi.324 Front & Top
(Grill removed for clarity)
7
SMC Enclosure
1
JBL Eyebolt System
The rear enclosure, fabricated from SMC (Sheet Molding
Compound), is in the form of a 2nd-order geometric design
for inherent strength, acoustic architecture, and transparent
aesthetics.
Located on the top (and bottom) is our standard JBL eyebolt
system to accommodate ceiling attachment (and floor
mounting system, see Foot Kit, page 19), when required.
2
14” LF/MF Transducers
Each 14-inch, LF (Low Frequency) and LF/Mid carbon-
fiber cone transducer features our patented dual-coil, dual-
gap Neodymium Differential Drive (NDD™) technology
for 1/5th the weight of conventional ferrite transducers with
twice the power handling. Moreover, each transducer is
driven by its own 600 watt D-class (digital) amplifier.
SMC Grille (not shown)
It looks like cloth, but it’s actually an anti-resonant, SMC-
reinforced, expanded steel grill, with an enhanced high
frequency spreading effect.
4
EVOi.324
Download from Www.Somanuals.com. All Manuals Search And Download.
F E A T U R E S
10
Handle/Grip
EVOi.324 REAR
As an aid for setup, the EVOi.324 is equipped with a built-
in carrying handle and grip.
11
XLR Audio / Communication
Input
8
EVO’s ‘brain’ is found in the EVOi.324. All transducer
controls and complex computational system functions take
place on the DSP (Digital Signal Processor) circuit board
within the aluminum housing. Working in tandem with the
optional EVOi.net, each EVOi.324 adapts to its acoustic
environment by generating its own test sequence, including
Auto-EQ and Delay Set settings. With Anti Feedback
Control, it also discriminates between feedback and
program music.
9
10
Hook-up is easy – simply use a standard XLR signal cable
to connect from an open EVOi.net Male XLR output (or
output from a mixer – see page 6) to the EVOi.324’s
Female XLR. No other cables are required. An internal
BiDAT™ (Bi-directional Data-over-Audio Transceiver)
communication system ensures that correct instructions are
sent and messages received across the signal cables.
11
12
12
Switch-Mode Power Supply
EVOi.324 uses a compact, lightweight, and highly efficient
digital power supply that does not require a large, heavy
toroidal transformer. This low-loss technology utilizes
digital modulation to regulate and supply the voltage
necessary to drive 1,300 watts of power amplification.
Figure 2 - EVOi.324 Rear
8
Compact Design
Insert the enclosed power cord into the IEC connector to
supply the specified AC power. (See “Hook-up Details” on
page 6 for more information.) The removable fuse protects
internal circuits. When replacing it, be sure to use the same
type as specified.
EVOi.324’s design has been dedicated to applications
requiring a permanent sound reinforcement solution. For a
1,300-watt Intelligent Powered Speaker System, it weighs
only 65 pounds (29.5 kg) and stands barely 42” (1.07
meters) tall.
9
D-Class Amplifier
Each EVOi.324 includes two digital amplifiers that are
extremely efficient. The energy from the power supply is
rapidly switched into each loudspeaker. The audio signal is
created as modulated pulses with switching rates many times
faster than the highest audio frequency. Because energy only
flows when needed, losses are substantially reduced as
compared to an equivalent sized conventional amplifier.
5
EVOi.324
Download from Www.Somanuals.com. All Manuals Search And Download.
H O O K - U P
D E T A I L S
AUDIO AND AC POWER CONNECTIONS
EVOi.324 Rear
Output on Generic Mixer
EVOi.net Rear
Power
Input
Sensitivity (direct in) +10 dBu
assuming no EQ has been applied.
OR
OR
XLR Signal Cable
EVOi.sys Rear
AC Main
Power Cord (supplied)
AC Mains
Fuse
Figure 3 - Basic EVOi.324 Audio and AC Connections
Power Cycle (Boot-up) Times
Maximum Drive Level = +10 dBu * Sensitivity
There are three simple audio hook-up options: all require
the use of high quality balanced signal cable with a Male
XLR connector. EVOi.324 requires a drive level of +10
dBu (sensitivity = +10 dBu assuming no external equaliza-
tion has been applied to the signal) for maximum perfor-
mance. Hooking a microphone directly to the input will
NOT drive it sufficiently. The output of a standard mixer,
EVOi.net or EVOi.sys should provide the optimum drive
level. (See the Sensitivity Chart in the Appendix, page 21)
EVOi.324’s internal DSP (Digital Signal Processor) circuit
board includes software applications. Like any device
operating software programs, there is a “boot-up” time lag
before EVOi.324 becomes fully operational. The audio
signal will be muted until the loudspeaker is fully
booted up. This should take approximately 20 seconds.
Upon connecting AC mains, the green
power indicator will illuminate. After
approximately 20 seconds there will be a
very quiet click as the system releases the
Power Requirements
mute. Upon power disconnection, the
green power indicator will flash several
times, however signal shut-down is
instantaneous. In summary, boot-up time
is approximately 20 seconds and shut-
down time is 0 seconds.
!
IMPORTANT: Each individual EVOi.324 is an extremely
powerful system and is quite capable of drawing peak
currents of up to 18 amps. Please consult a qualified
electrician for correct installation and power connection.
For more information, see AC Requirements on page 21.
CAUTION: to reduce the risk of fire, replace fuse with
same type and rating: ATTENTION: utiliser un fusible de
rechange de meme type de:
115V~ T6.3A/250V~
230V~ T3.15A/250V~
WARNING! When EVOi.324 is on,
the amplifier heatsink will get hot
even when no signal is being passed.
This is normal operation for D-Class
amplifiers.
* 0 dBu = 0.775 Volts; +10 dBu = 2.45 Volts
6
EVOi.324
Download from Www.Somanuals.com. All Manuals Search And Download.
A P P L I C A T I O N S
INTENDED APPLICATIONS
EVO Loudspeaker Systems have been optimized for small to mid-size venues, where a pair will sufficiently reinforce
sound for an audience of up to five hundred people. They have been designed with specific applications in mind: schools
and sports facilities; places of worship; and performance venues. Typically the program of events are quite varied and high
quality reinforcement is required for speech, live music and recorded music playback. Figures 4-7 below show some typical
type venues and an identifiable area that requires sound reinforcement, we identify this as the listening area. This section
describes how to optimize the placement and position of the EVO Loudspeaker in these typical applications in order that the
entire listening area receives good sound. These are very simple instructions and are for ideal situations. As guidelines, they
are approximate and it may not be possible to follow them in all situations. In the end, final aiming decisions must be based
on what is actually heard when walking the room. Use your ears.
Schools and Sports Facilities
Performance Venues
= Listening Area
= Listening Area
Figure 4
Figure 5
Places of Worship
Rectangular-Shaped Room
Places of Worship
Fan-Shaped Room
= Listening Area
Figure 7
= Listening Area
Figure 6
7
EVOi.324
Download from Www.Somanuals.com. All Manuals Search And Download.
A P P L I C A T I O N S
LOUDSPEAKER BASICS
EVO Sound System Design Basics
The primary function of a sound reinforcement system is to make sure that all of the listeners in a given audience area are
able to understand the speech and/or lyrics that are being reinforced. The intelligibility of a loudspeaker system is a measure
of how “understandable” its output is. Intelligibility is optimized when the sound radiated from the loudspeaker is primarily
directed to the audience areas and away from microphones and reflective surfaces in the room.
In order to ensure that the radiated sound is directed primarily to the audience areas, great care must be taken in deciding on
loudspeaker placement and aiming. Understanding a loudspeaker’s coverage angles and the proper application of those
coverage angles is the first step towards designing a great sound reinforcement system.
EVOi.324 Coverage Angles
The majority of the sound coming from the EVOi.324 loudspeaker radiates at an angle of 80 degrees in the speaker’s
horizontal (side-to-side) plane and 80 degrees in the speaker’s vertical (top-to-bottom) plane. (Figures 8 and 9.)
Horizontal Coverage Angles
Vertical Coverage Angles
Horizontal Coverage = 80°
Vertical Coverage = 80°
EVOi.324
(top view)
EVOi.324
(side view)
+40°
80°
80°
0°
(on-axis)
-40°
+40°
0°
(on-axis)
Figure 8 - 80° Horizontal
Coverage
Figure 9 - 80° Vertical
Coverage
-40°
8
EVOi.324
Download from Www.Somanuals.com. All Manuals Search And Download.
A P P L I C A T I O N S
The Throw Ratio
EVOi.324 Coverage Angles
Placing this 80° x 80° speaker up in the air and pointing it
towards an audience area will result in a defined area of
coverage.
Based on its area of coverage performance, the EVOi.324
has a height-to-depth Throw Ratio of 1:3. This Throw
Ratio can be used to optimally position the loudspeaker.
For example, if the EVOi.324 is installed at a height of 10’,
it will “throw” to a distance of 30’ away from the loud-
speaker and hence provide optimized coverage up to 30’
away.
Figure 10 - Area of
Coverage
Refer to Table 1 and Figure 11 below to identify either:
i. The throw (optimized coverage distance), for a given
fixed (pre-determined) height above the floor.
Out of Coverage
ii. The installation height necessary to provide the desired
throw (optimized coverage distance).
Aiming Point
Downward
Installation (Distance from Tilt Aiming
Throw *
30'
40'
50'
60'
70'
80'
90'
Height
10'
13' 4"
16' 8"
20'
23' 4"
28' 8"
30'
33' 4"
36' 8"
40'
Loudspeaker)
20'
Angle
26.6°
26.6°
26.6°
26.6°
26.6°
26.6°
26.6°
26.6°
26.6°
26.6°
Optimized Coverage
Reduced Loudness
26' 8"
33' 4"
40'
46' 8"
53' 4"
60'
66' 8"
73' 4"
80'
Note that this area of coverage actually includes three
different areas: an area of “optimized coverage” (black); an
area of “reduced loudness” (gray); and an area “out of
coverage” (white).
100'
110'
120'
* Optimized Coverage Distance
Understanding the optimum performance of the EVO
Loudspeaker through the use of a simple Throw Ratio and
Aiming guide line will help you achieve optimized
coverage over your defined listening area.
Table 1 : Throw Ratio
26.6°
20'
B
A
26.6°
10'
70'
60'
50'
40'
30'
20'
Throw (Optimized Coverage Distance) A
Throw (Optimized Coverage Distance) B
10'
Figure 11 - Throw Ratio
9
EVOi.324
Download from Www.Somanuals.com. All Manuals Search And Download.
A P P L I C A T I O N S
Using More Than One Speaker
LOUDSPEAKER BASICS
Stereo and Arrays
Aiming EVO
So far we have discussed the simplest sound reinforcement
system configuration, a single EVO loudspeaker. Most
applications will require the use of more than one
EVOi.324, either because a stereo Left – Right effect is
required (see Figure 12)...
Once the optimum height of the EVO loudspeaker has been
identified it needs to be aimed to achieve the desired
coverage area. The point at which to aim is derived from a
simple height-to-depth aiming ratio of 1:2. For example, if
the EVOi.324 is installed at a height of 10’, it will “throw”
to a distance 30’ away provided it is aimed to a point 20’
away. Refer to Table 1 and Figure 11 on page 9.
Stage
Maximum Performance Guideline
You may have noted from Table 1 that the guide does not
provide figures above a 40’ installation height. Above a
height of 40’ the useful throw and optimized coverage area
will not grow, in fact it will probably start to deteriorate
depending on the natural acoustics of the room.
0°
( on-axis)
The guidelines below can be used to determine the maxi-
mum performance achievable for a given loudspeaker
height above the listening area.
Figure 12 - Stereo Left Right Placement
...or additional coverage is required (e.g. for a wider
listening area). In this case, two EVOi.324s could be
arrayed together as in Figure 13.
Program
Requirement
Maximum
Height
40’
Maximum
Throw
120’
Speech only
Stage
Speech + acoustic music
Amplified live music
Loud, playback music
40’
20’
20’
120’
60’
60’
0°
(on-axis)
0°
(on-axis)
-40°
140°
+40°
60°
Optimum
Listening
Area
Optimum
Listening
Area
Figure 13 - Mono Two Speaker Array
Figure 14 to the left shows the optimum “Splay Angle” of
60° for a combined optimum horizontal coverage of 140°.
0°
(on-axis)
0°
(on-axis)
-40° +40°
Exactly the same guidelines that are used for one loud-
speaker can be used for more than one: the Throw Ratio
and Aiming Ratio.
Figure 14 - Optimum Splay Angle
10
EVOi.324
Download from Www.Somanuals.com. All Manuals Search And Download.
A P P L I C A T I O N S
LOUDSPEAKER BASICS
When to use Delay Speakers
The use of more than one EVOi.324 may be necessary in
venues with extremely long listening areas.
Note that the sound from the delay speaker must be “in
sync” with the sound from the main speaker. This is
achieved by appropriately delaying the audio signal
arriving at the delay speaker and also by reducing its
overall output level. While these adjustments typically
require the use of complex measurement equipment,
expensive delay devices and years of audio experience,
they can be made automatically through the use of the
optional EVOi.net controller.
For example if the listening area is 120’ in depth and the
required performance is for “Loud Playback Music” the
Maximum Performance Guideline on page 10 indicates a
maximum 20’ installation height. This will provide 60’ of
throw. To cover the remaining 60’ of listening area, a
second auxiliary/delay speaker is required (see Figure 15).
40'
26.6°
26.6°
20'
20'
B
A
140'
120'
100'
80'
60'
40'
20'
Throw (Optimized Coverage Distance) A
Throw (Optimized Coverage Distance) B
Figure 15: Basic Delay Speaker Placement
11
EVOi.324
Download from Www.Somanuals.com. All Manuals Search And Download.
A P P L I C A T I O N S
As a guide this section provides some typical configurations for EVOi.324 installations, the approximate locations of each
EVOi.324 and the aiming position in the room. Please note that when the installation requires the additional support of an
auxiliary (Delay) EVOi.324s to cover larger listening areas, the use of EVOi.net is highly recommended as this will access the
automated “delay-set” feature.
EVOi.324s IN RECTANGULAR ROOMS
Small Rectangular Room:
1 Main (Mono)
This is the simplest configuration. In this example, figure
16, one EVOi.324 will cover the entire listening area.
Stereo is not required, as this system is predominantly used
to reinforce speech only. The EVOi.324 is positioned 20’
above the floor and aimed to a point 40’ away on the
central axis of the room. Optimum coverage will be
provided up to 60 feet away.
Main
20’
0'
0°
0'
2
60
’
= Listening Area
40'
Figure 16
60'
Longer Rectangular Room:
1 Main (Mono) + 1 Delay (Mono)
For a longer room additional coverage will be required to
cover the back rows of the listening area. This can be
achieved using an additional auxiliary (Delay) EVOi.324 as
shown in Figure 17.
Main
20
’
Delay*
0'
0°
20'
40'
0°
60'
Figure 17
60
’
= Listening Area
80'
* Use EVOi.net
to set actual delay
and level.
60'
12
EVOi.324
Download from Www.Somanuals.com. All Manuals Search And Download.
A P P L I C A T I O N S
EVOi.324s IN RECTANGULAR ROOMS
Small/Wider Rectangular Room:
2 Main (Stereo)
For a wider room or where a stereo program is required
each EVOi.324 should be aimed according to the 1:3
“throw ratio” described in the previous section (page
8 & 9). In this example, the EVOi.324s are
positioned 20’ high and aimed 40’ away. They will
provide optimum coverage up to 60’ away. In
addition, they should both be aimed at a single
point 40’ away, the central axis of the room, as seen
in Figure 18.
L
R
20’
0°
0'
80
’
= Listening Area
20'
Figure 18
40'
60'
Longer/Wider Rectangular Room:
2 Main (Stereo) + 2 Delay (Stereo)
For additional coverage in a longer room, two more
auxiliary (Delay) EVOi.324s can be used, positioned and
aimed as shown in Figure 19.
L
L Delay*
R
20
’
R Delay*
0°
0'
20'
Figure 19
40'
80
’
= Listening Area
60'
* Use EVOi.net
to set actual delay
and level.
0'
8
100'
13
EVOi.324
Download from Www.Somanuals.com. All Manuals Search And Download.
A P P L I C A T I O N S
EVOi.324s IN RECTANGULAR ROOMS
Larger/Wider Rectangular Rooms:
2 Main (Mono Array) + 2 Delay (Mono Array)
In a wide room where a stereo program is not necessary the Main and Delay EVOi.324s can be configured into Arrays for
broader coverage and supplied with a mono signal. (See page 10 for array specifics.) Figure 20 shows such an application.
L
R
L Delay*
20
R Delay*
’
0°
0'
20'
1
0
40'
0
’
= Listening Area
60'
* Use EVOi.net
to set actual delay
and level.
0'
8
Figure 20
100'
14
EVOi.324
Download from Www.Somanuals.com. All Manuals Search And Download.
A P P L I C A T I O N S
EVOi.324s IN FAN SHAPED ROOMS
Small Fan Shaped Room:
1 Main (Mono)
Like the small rectangular room, a simple configuration of
one EVOi.324 will provide enough coverage for the entire
listening area. Stereo is not required, as this system is
predominantly used to reinforce speech only. The
EVOi.324 is positioned 20’ above the floor and aimed to a
point 40’ away on the central axis of the room. Optimum
coverage will be provided up to 60’ away as shown in
Figure 21.
Main
20
’
0'
0°
0'
2
60
’
Figure 21
= Listening Area
40'
60'
Medium Fan Shaped Room:
2 Main (Mono Array)
In a wider room where a Mono program is required two
EVOi.324s can be arrayed together to provide wider
coverage. These are positioned as described in Figure 22
below.
L
R
20
’
0'
0°
80
20'
’
= Listening Area
40'
Figure 22
60'
15
EVOi.324
Download from Www.Somanuals.com. All Manuals Search And Download.
A P P L I C A T I O N S
EVOi.324s IN FAN SHAPED ROOMS
Large Fan Shaped Room:
2 Main (Mono Array) + 2 Delay (Mono)
A larger version of the previous example, Figure 23, illustrates
the positioning of two Delay EVOi.324s to cover the listening
area that falls outside the optimum coverage of the Main
EVOi.324 Array.
L
R
L Delay*
2
0
’
R Delay*
0'
0°
20'
40'
100
’
60'
= Listening Area
Figure 23
* Use EVOi.net
to set actual delay
and level.
80'
100'
16
EVOi.324
Download from Www.Somanuals.com. All Manuals Search And Download.
P A I N T I N G
EVOi.324 is readily paintable. The SMC (Sheet Molded
Compound) provides a lightly textured surface that any
standard household or industrial paint readily adheres to.
The result is a sound reinforcement system that is able to
blend unobtrusively into the decor of its environment.
2. Prepare all surfaces by wiping off dust and cleaning with
a damp cloth. It may be necessary to use a mild household
cleaner to remove grease.
3. Carefully mask the aluminum electronics enclosure on
the back of the speaker. IT SHOULD NOT BE PAINTED.
Removal of the electronics enclosure should only be done
by qualified service personnel.
Instructions for Painting:
1. It is strongly recommended that EVOi.324 be partially
disassembled to obtain optimum results. This requires
removing the grill, the handle bar, and suspension point
placeholder screws.
4. Carefully mask the baffle area. Avoid getting paint on the
loudspeaker cones or in the waveguide. It’s not a good
thing.
A. Remove the grill screw covers by gently prying off.
B. Remove six grill retain screws.
C. Remove four allen head screws from the grill frame.
D. Remove the grill taking care to keep the grill and grill
supports together.
5. Apply as many coats of paint as is required. Standard
household or industrial paints (i. e. waterbased latex or
enamel) will provide the best results. Spraying many thin
coats will provide the best results.
E. Remove all six suspension placeholder screws.
F. Remove the four allen screws retaining the handle bar
and remove the bar.
6. Assemble the EVOi.324 in reverse order as described in
Step One.
E
Figure 24 - Exploded View for Painting
D
C
F
A
B
E
C
17
EVOi.324
Download from Www.Somanuals.com. All Manuals Search And Download.
I N S T A L L A T I O N
Overview
For Example: Maximum Load Rating divided by EVOi.324
Net Weight = The number of speakers in a vertical array.
EVOi.324 has been designed to be permanently installed.
An eyebolt kit has been provided to facilitate suspension
from above: a ceiling, a beam or overhang. EVOi.324
weighs 65 pounds (29.5 Kg) and attaching this loudspeaker
to a surface is a task that should not be taken lightly.
Always consult a qualified person.
142.8 lb (67.8 Kg) / 65 lb (29.5 Kg) = 2.1
Therefore only two EVOi.324s may be used in a vertical
array if they are suspended from the points located on the
top of the enclosure in either recommendations 1 and 2
stated above.
Suspension
WARNING !! Suspending this system should be done by
qualified persons following safe rigging standards. For
more information, please refer to the JBL Technical
Note Volume 1, Number 14 – Basic Principles for
Suspending Loudspeaker Systems.
Eyebolt Kit
Parts Included:
3
3
1
Shoulder Eyebolts
Washers
Suspension Advisory and Tech Note
Installing Eyebolts:
1. Remove suspension
placeholder screws.
2. Coat each eyebolt
with thread-locking
material (e.g., LocTite
#2 or equivalent).
3. Using the included
washers as stand-offs,
thread the eyebolts
into the open holes
and tighten.
Before suspending an EVOi.324, be sure to inspect all
components for cracks, deformations, corrosion, and/or
missing or damaged parts that could reduce the strength
and safety of the installation.
Placeholder
Bolt
Perform all calculations to ensure that all components are
used within their rated work load before suspending an
EVOi.324. Remember the weakest component determines
the size and safety of the entire installation.
There are 3 suspension points on the top and bottom of
EVOi.324, two toward the front of the enclosure and one to
the rear. Pull tests at a certified test facility have docu-
mented non-catastrophic failure at 450 – 550 pounds for
each individual front suspension point and 1000 pounds for
the rear suspension point.
Figure 25 - Remove
Placeholder Bolts
Eyebolt
Washer
It is recommended that EVOi.324 be either suspended:
1. Equally from both of the front suspension points
together, or
2. From the rear suspension point, with the addition of a
safety cable to another suspension point.
Figure 26 - Install Washers
and Eyebolts
For both recommendations, assuming a 7:1 safety factor,
the load on the suspension points should NEVER be greater
than 142.8 pounds (67.8 Kg).
18
EVOi.324
Download from Www.Somanuals.com. All Manuals Search And Download.
I N S T A L L A T I O N
Foot Kit
iv. Screw the large rubber foot into the suspension position
for the required aiming angle. For example, screw it all
the way in and EVOi.324 will aim up slightly.
Unscrewing it will begin to tilt EVOi.324 down.
v. Important: Once the large rubber foot is positioned
correctly tighten the nut onto the washer. This will
ensure the weight is transferred to the enclosure and not
the suspension insert.
The Foot Kit must be utilized if EVOi.324 is to be used
“Free Standing”. It provides a much more stable base and
also a mechanism that compensates for the shape and angle
of the bottom of the enclosure.
Parts Included:
2 x Small Rubber Feet
1 x Large Rubber Foot, threaded with nut
1 x Washer
Installing Feet:
i. Remove suspension insert screws from the bottom of
the enclosure.
1 Turn Foot To
Set Tilt.
2 Tighten
Screw.
Foot
Washer
Placeholder
Bolt
Nut
Adjustable
Foot
Placeholder
Bolt
Figure 27 - Remove Lower Placeholder Bolts
2 Tighten Nut.
ii. Using two of the removed suspension placeholder
screws attach the small rubber feet to the front
suspension positions. Please note that there is an
orientation to the small rubber feet which compensates
for the angle of the enclosure surface.
1 Turn Foot To
Set Height.
Figure 28 - Install Feet
iii. Place the large washer over the rear suspension
position. Make sure the nut is threaded onto the large
rubber foot. Then insert the threaded portion through
the washer and into the rear suspension position.
19
EVOi.324
Download from Www.Somanuals.com. All Manuals Search And Download.
T R O U B L E S H O O T I N G
3. EVOi.324 powers up, the LED on rear panel
lights up, but doesn’t pass audio:
The EVOi.324 loudspeaker system has been precision
engineered for optimum performance with a minimum of
maintenance and outside intervention.
i. Less than 20 seconds have passed. Wait for a couple of
moments as EVOi.324 Boots-up.
ii. Check that there is audio signal present:
AC Power
-
Is there a signal cable connected? If so, check that
it is not defective.
Is there signal coming out of the mixer?
Is EVOi.net attached? (See EVOi.net manual.)
The EVOi.324 speaker contains a high-powered amplifier
system. Due to the remote locations likely for install, there
is no power switch. Application of the AC Mains power
will result in the EVOi.324 starting up and initializing (boot
process takes about 20 seconds). There is a slight power
draw even when EVOi.324 is not passing audio (approxi-
mately equivalent to a 100W light bulb (see AC Power
requirements page 21). It may be desirable to place a
switch on its circuit. This switch should be appropriately
rated and installed by a competent electrician in full
compliance with all applicable national and local electrical
codes.
-
-
iii. If none of the above then immediately contact your
Dealer.
4. The system doesn’t get any louder no matter
how much the input signal is turned up:
i. Is it really loud already? Built-in limiters are specially
calibrated to prevent damaging levels to the individual
speakers in EVOi.324. These limiters are designed to
be as transparent as possible while still providing
necessary protection functionality. It doesn’t get any
louder because it is working, protecting itself!
1. EVOi.324 doesn’t power up:
i. Is it plugged in?
ii. Is the AC Mains circuit adequate for system and
energized?
5. The sound system is making a terrible noise:
i. If a microphone is being used in the system you may be
hearing feedback. Turning down the level of the
microphone and/or repositioning it may help. Using
EVOi.net you can start the Anti Feedback control built
into EVOi.324.
ii. Is tape deck playback level up? Electrical feedback
may be present. Try lowering the tape deck playback
level. Check that the tape deck is not connected to the
record outputs.
Due to the highly efficient nature of the electronics, there
will be a direct correlation between signal level and current
draw. While it may be possible to start multiple systems on
one AC circuit, continued high level operation may result in
occasional brown-outs (see AC Power Requirements on
page 21).
2. The Power LED is Flashing:
i. The AC Main voltage is inadequate or out of the rated
range (see AC Power requirements page 21).
ii. The AC Mains is not appropriate for the model (i.e.
120V model for 120V service). Check the voltage
stated on the rear input label and return to the Dealer if
incorrect.
iii. The fuse may have blown. CAUTION: to reduce the
risk of fire, replace the fuse with the same type and
rating.
iv. If none of the above then immediately contact your
Dealer.
20
EVOi.324
Download from Www.Somanuals.com. All Manuals Search And Download.
A P P E N D I X
Current Requirements
AC Power Requirements
EVOi.324 will not draw a continuous current. Acting as a
dynamic load on the AC supply, the current drawn will vary
dependant on the operating level, e.g. quiet levels and loud
levels in the program.
In the United States, the EVOi.324 is supplied with an
Edison type plug. For other countries, the correct plug must
be used in accordance with the local requirements. For
Europe and the rest of the world the correct AC supply lead
will be supplied.
Understanding the amount of current drawn is essential
when using EVOi.324.
Voltage Requirements
EVOi.324 will operate continuously provided the AC
Voltage falls within the following ranges:
The EVOi.324 is capable of drawing peak currents of up to
18 Amps. Any cabling used should be of a suitable gauge to
reflect this. Inadequate cabling can cause large voltage
drops over distance and potentially cause ‘brown-out’.
Standard AC Voltage
Voltage Range
+/- 10%
Frequency
50/60Hz
50/60Hz
120v
230v
+/- 10%
ALWAYS CONSULT A QUALIFIED ELECTRICIAN
Brown-out Conditions
If the voltage falls below this range, the EVOi.324 will
‘brown-out’. During ‘brown-out’ the audio signal will
momentarily mute during very high level program. Should
the supply voltage permanently remain below this supply
voltage, then the EVOi.324 will shut down. When the AC
supply falls within the above stated ranges, EVOi.324 will
switch on again, and operate normally.
EVOi.324 Sensitivity Chart
Electrical Input
Volts (AC RMS)
Acoustic Output
Measured SPL
(dB re: 20uPa)
dBu
-25
-20
-15
-10
-5
To avoid ‘brown-out’ EVOi.324 should be operated with an
AC supply that adequately falls within the above stated
ranges.
0.04
0.08
0.14
0.25
0.44
0.78
1.38
1.95
2.45
91
96
101
106
110
116
118
120
122
0
5
8
10
101 dB = Equivalent 1w/1m Specification
21
EVOi.324
Download from Www.Somanuals.com. All Manuals Search And Download.
T E C H N I C A L
D A T A
E V O i . 3 2 4 S p e c i f i c a t i o n s
Frequency Range (-10 dB):
Freq. Response (-3 dB):
Horizontal Coverage (-6 dB):
Vertical Coverage (-6 dB):
Directivity Factor (Q):
Directivity Index (DI):
Equivalent Sensitivity:
Dimensions (H x W x D):
Net Weight:
40 Hz - 18 kHz
48 Hz - 16 kHz
80° (averaged 500 Hz -16 kHz)
80° (averaged 500 Hz -16 kHz)
11.4 (averaged 500 Hz -16 kHz)
10.6 dB (averaged 500 Hz - 16 kHz)
101 dB (-15 dBu @ 1 meter = 1 watt/meter)
42 x 13.9 x 15.2” (1067 x 353 x 386.2 mm)
65 lbs. (29.48 Kg)
Low Frequency Driver:
14” NDD, Carbon Fiber Cone, Dual 2” Voice Coils,
Integral Thermomaster
Low Frequency/Mid Driver:
High Frequency Driver:
14” NDD, Carbon Fiber Cone, Dual 2” Voice Coils,
Integral Thermomaster
2430, Large Format, 1.5” Exit Compression Driver with a Neodymium
Motor, 100 Watt 3” Encapsulated Voice Coil, Aluminum Diaphragm
Aluminum thermally coupled to 2430 via “silpad” gasket
440 Hz load ref = 6 Ohms, Input = 1.4 Vrms/5.14 dBu,
Output = 300W rms, THD<0.3%
330 Wrms (with Limiters)
Waveguide:
Amplifier Power Low Frequency:
Max. Continuous Output:
Burst Output:
600 Wrms
Signal-to-Noise Ratio:
Amplifier Power LF/Mid:
>90 dB A weighted
440 Hz load ref = 6 Ohms, Input = 1.4 Vrms/5.14 dBu,
Output = 300 Wrms, THD<0.3%
330 Wrms (with Limiters)
Max. Continuous Output:
Burst Output:
600 Wrms
Signal-to-Noise Ratio:
Amplifier Power HF:
>90 dB A weighted
3 kHz load ref = 8 Ohms, Input = 3.2 Vrms/12.3 dBu,
Output = 35 Wrms, THD<0.2%
50 Wrms (with Limiters)
Maximum Continuous Output:
Burst Output:
100 Wrms
Signal-to-Noise Ratio:
Audio Connectors:
>90 dB A weighted
Balanced XLR
LF Crossover Frequency:
LF/Mid Crossover Frequency:
HF Crossover Frequency:
Limiting:
250 Hz
1.25 kHz
1.25 kHz
Dynamic Amplifier Clip Prevention
Parametric
Transducer EQ type:
22
EVOi.324
Download from Www.Somanuals.com. All Manuals Search And Download.
W A R R A N T Y
JBL Limited Warranty
present the original bill of sale to establish the date of
purchase. Please do not ship your JBL product to the
factory without prior authorization. If transportation of your
JBL product presents any unusual difficulties, please advise
us and we may make special arrangements with you.
Otherwise, you are responsible for transporting your
product for repair or arranging for its transportation and for
payment of any initial shipping charges. However, we will
pay the return shipping charges if repairs are covered by the
warranty.
The JBL Limited Warranty on professional loudspeaker
products (except for enclosures) remains in effect for five
years from the date of the first consumer purchase. JBL
amplifiers are warranted for three years from the date of
original purchase. Enclosures and all other JBL products
are warranted for two years from the date of original
purchase.
Who Is Protected by This Warranty?
Your JBL Warranty protects the original owner and all
subsequent owners so long as: A.) Your JBL product has
been purchased in the Continental United States, Hawaii or
Alaska. (This Warranty does not apply to JBL products
purchased elsewhere except for purchases by military
outlets. Other purchasers should contact the local JBL
distributor for warranty information.); and B.) The original
dated bill of sale is presented whenever warranty service is
required.
Limitation of Implied Warranties
ALL IMPLIED WARRANTIES, INCLUDING WARRAN-
TIES OF MERCHANTABILITYAND FITNESS FOR
PARTICULAR PURPOSE, ARE LIMITED IN DURA-
TION TO THE LENGTH OF THIS WARRANTY.
EXCLUSION OF CERTAIN DAMAGES
JBL’S LIABILITY IS LIMITED TO THE REPAIR OR
REPLACEMENT, AT OUR OPTION, OF ANY DEFEC-
TIVE PRODUCT AND SHALL NOT INCLUDE INCI-
DENTAL OR CONSEQUENTIAL DAMAGES OF ANY
KIND. SOME STATES DO NOT ALLOW LIMITATIONS
ON HOW LONG AN IMPLIED WARRANTY LASTS
AND/OR DO NOT ALLOW THE EXCLUSION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO
THE ABOVE LIMITATIONS AND EXCLUSIONS MAY
NOT APPLY TO YOU. THIS WARRANTY GIVES YOU
SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO
HAVE OTHER RIGHTS WHICH VARY FROM STATE
TO STATE.
What is Covered by the JBL Warranty?
Except as specified below, your JBL Warranty covers all
defects in material and workmanship. The following are not
covered: Damage caused by accident, misuse, abuse,
product modification or neglect; damage occurring during
shipment; damage resulting from failure to follow instruc-
tions contained in your Instruction Manual; damage
resulting from the performance of repairs by someone not
authorized by JBL; claims based upon any misrepresenta-
tions by the seller; any JBL product on which the serial
number has been defaced, modified or removed.
JBL Professional Contact Information
Mailing Address
JBL Professional
8500 Balboa Blvd.
Northridge California 91329
Who Pays for What?
JBL will pay all labor and material expenses for all repairs
covered by this warranty. Please be sure to save the original
shipping cartons because a charge will be made if replace-
ment cartons are requested. Payment of shipping charges is
discussed in the next section of this warranty.
Customer Service
Monday through Friday 8:00am - 5:00pm Pacific Coast
Time
How to Obtain Warranty Performance
If your JBL product ever needs service, write or telephone
us at JBL Incorporated (Attn: Customer Service Depart-
ment), 8500 Balboa Boulevard, PO. Box 2200, Northridge,
California 91329 (818/893-8411). We may direct you to an
authorized JBL Service Agency or ask you to send your
unit to the factory for repair Either way, you’ll need to
In the U.S.A. (800) 8JBLPRO (800.852.5776)
23
EVOi.324
Download from Www.Somanuals.com. All Manuals Search And Download.
N O T E S
24
EVOi.324
Download from Www.Somanuals.com. All Manuals Search And Download.
I N D E X
AC Requirements . . . . 6, 20, 21
Power Supply . . . . 5
Accessories . . . . 2
Eyebolt Kit . . . . 2, 4, 18
Foot Kit . . . . 2, 4, 19
Aiming . . . . 10
Safety Information . . . . 1
School and Sports Facilities . . . . 7
Speaker Placement . . . . 9-16
Specifications . . . . 22
Technical Data . . . . 22
Thermomaster Vents . . . . 4
Throw Ratio . . . . 9
Appendix . . . . 21
Applications . . . . 7
Troubleshooting . . . . 20
Warranty . . . . 23
School and Sports Facilities . . . . 7
Performance Venues . . . . 7
Places of Worship . . . . 7
Components
Amplifiers . . . . 5
High Frequency . . . . 4
Low Frequency . . . . 4
Mid Frequency . . . . 4
Cooling . . . . 4
Thermomaster Vents . . . . 4
Coverage Angles . . . . 9
Delay Speakers . . . . 11-16
Design Overview . . . . 3
Eyebolt Kit . . . . 2, 4, 18
Inputs . . . . 5
Introduction . . . . 2
Fan Shaped Rooms . . . . 15-16
Features . . . . 4
EVOi.324 Front/Top . . . . 4
EVOi.324 Rear . . . . 5
Foot Kit . . . . 2, 4, 19
Hanging Speakers . . . . 18
Hook-Up Details . . . . 6
Installation . . . . 18
Loudspeaker Basics . . . . 8
Maximum Performance Guideline . . . . 10
Multiple Speakers . . . . 10
Package Contents . . . . 2
Painting . . . . 17
Performance Venues . . . . 7
Places of Worship . . . . 7
Power Cycle Times . . . . 6
Problems . . . . 20
Rectangular Rooms . . . . 12-14
EVOi.324
Download from Www.Somanuals.com. All Manuals Search And Download.
A Harman International Company
JBL Professional • 8500 Balboa Boulevard • Northridge, CA 91329
Part # 981-00057-00
© Copyright 2001 JBLProfessional • Printed in the USA
Download from Www.Somanuals.com. All Manuals Search And Download.
|