PE10P-X-X-A0S
OPERATOR’S MANUAL
INCLUDING: OPERATION, INSTALLATION & MAINTENANCE
RELEASED: 9-14-04
REVISED:
11-15-10
08)
(REV.
1” DIAPHRAGM PUMP
1:1 RATIO (NON-METALLIC)
READ THIS MANUAL CAREFULLY BEFORE INSTALLING,
OPERATING OR SERVICING THIS EQUIPMENT.
It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.
SERVICE KITS
Refer to Model Description Chart to match the pump material options.
637396-XXforfluidsectionrepair(seepage4).NOTE:Thiskitalsocon-
tains several air motor seals which will need to be replaced.
637412 for air section repair (see page 6).
PUMP DATA
Models . . . . . . . . . . see Model Description Chart for “-XXX”.
PE10P-AXS-XXX-A0S
PE10P-BXS-XXX-A0S
PE10P-YXS-XXX-A0S
Figure 1
Pump Type . . . . . . . Non-MetallicAir Operated Double Diaphragm
Material . . . . . . . . . . see Model Description Chart.
Weight . . . PE10P-AKS-XXX-A0S . . . 25.40 lbs (11.52 kgs)
PE10P-APS-XXX-A0S . . . 18.92 lbs (8.58 kgs)
PE10P-BKS-XXX-A0S . . . 25.40 lbs (11.52 kgs)
PE10P-BPS-XXX-A0S . . . 18.92 lbs (8.58 kgs)
PE10P-FXS-XXX-A0S
PE10P-FKS-XXX-A0S . . . 26.72 lbs (12.12 kgs)
PE10P-FPS-XXX-A0S . . . 19.44 lbs (8.82 kgs)
MODEL DESCRIPTION CHART
PE10P-YKS-XXX-A0S . . . 26.29 lbs (11.93 kgs)
PE10P-YPS-XXX-A0S . . . 19.16 lbs (8.69 kgs)
PE10 P - X X S - X X X - A0S
Maximum Air Inlet Pressure . . . . . . . . . 120 p.s.i.g. (8.3 bar)
Maximum Material Inlet Pressure . . . . . 10 p.s.i.g. (0.69 bar)
Maximum Outlet Pressure . . . . . . . . . . 120 p.s.i.g. (8.3 bar)
Maximum Flow Rate (flooded inlet) . . . . 53.0 g.p.m. (200.6 l.p.m.)
Displacement / Cycle @ 100 p.s.i.g. . . . 0.226 gal. (0.86 lit.)
Maximum Particle Size . . . . . . . . . . . . 1/8” dia. (3.2 mm)
Maximum Temperature Limits (diaphragm / ball / seal material)
E.P.R. / EPDM . . . . . . . . . . . -60_to280_F (-51_to 138_C)
HytrelR . . . . . . . . . . . . . . . . -20_ to 150_ F (-29_ to 66_ C)
Nitrile . . . . . . . . . . . . . . . . . 10_ to 180_ F (-12_ to 82_ C)
Polypropylene . . . . . . . . . . . 35_ to 175_ F ( 2_ to 79_C)
PVDF (KynarR) . . . . . . . . . . 10_ to 200_ F (-12_ to 93_ C)
SantopreneR . . . . . . . . . . . -40_to225_F (-40_to 107_C)
PTFE . . . . . . . . . . . . . . . . . 40_ to 225_ F (4_ to 107_ C)
VitonR . . . . . . . . . . . . . . . . -40_to350_F (-40_to 177_C)
Dimensional Data . . . . . . . . . . . . . . . . see page 8
Mounting Dimension . . . 5.032” x 10.050” (127.8 mm x 255.3 mm)
Noise Level @ 70 p.s.i., 60 c.p.m. . . . . . 79.7 db(A){
Center Section Material
P - Polypropylene
Fluid Connection / Location
A - 1 --11-1/2 N.P.T.F. - 1
B - Rp 1 - 11 BS
F - 1” A.N.S.I. / DIN Flange / End
Y - 1” A.N.S.I. / DIN Flange / Center
Fluid Caps & Manifold Material
K - PVDF (Kynar)
P - Polypropylene
Hardware Material
S - Stainless Steel
Seat Material
H - Hard 440 Stainless Steel
K - PVDF (Kynar)
P - Polypropylene
S - 316 Stainless Steel
The pump sound pressure levels published here have been updated to an Equivalent
Ball Material
Continuous Sound Level (L ) to meet the intent of ANSI S1.13-1971, CAGI-PNEU-
Aeq
A - Santoprene
C - Hytrel
T - PTFE
V - Viton
ROP S5.1 using four microphone locations.
G - Nitrile
NOTICE: All possible options are shown in the chart, however, certain
combinations may not be recommended, consult a representative or the
factory if you have questions concerning availability.
Diaphragm Material
A - Santoprene
C - Hytrel
M - Medical Grade Santoprene
T - PTFE / Santoprene
V - Viton
G - Nitrile
FLUID SECTION SERVICE KIT SELECTION
PE10P - XXS - X X X - A0S
637396 - X X
EXAMPLE: MODEL # PE10P-FPS-PAA-A0S
FLUID SECTION SERVICE KIT # 637396-AA
Ball
Diaphragm
INGERSOLL RAND COMPANY LTD
209 NORTH MAIN STREET -- BRYAN, OHIO 43506
(800)ꢀꢁꢂꢃꢄꢅꢆꢇ Dꢈ)$;ꢉꢊꢄꢄꢋꢊꢁꢅꢃꢇꢅꢆꢇ
E2010
CCN 15214158
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL DESCRIPTION
OPERATING INSTRUCTIONS
The ARO diaphragm pump offers high volume delivery even at low air
pressure and a broad range of material compatibility options available.
Refer to the model and option chart. ARO pumps feature stall resistant
design, modular air motor / fluid sections.
Air operated double diaphragm pumps utilize a pressure differential in
theairchamberstoalternatelycreatesuctionandpositivefluidpressure
in the fluid chambers, ball checks insure a positive flow of fluid.
Pump cycling will begin as air pressure is applied and it will continue to
pump and keep up with the demand. It will build and maintain line pres-
sure and will stop cycling once maximum line pressure is reached (dis-
pensing device closed) and will resume pumping as needed.
S Always flush the pump with a solvent compatible with the material
being pumped ifthe materialbeing pumpedissubjectto “settingup”
when not in use for a period of time.
S Disconnecttheairsupplyfromthepumpifitistobeinactiveforafew
hours.
PARTS AND SERVICE KITS
Refer to the part viewsanddescriptionsasprovided onpages4through
7 for parts identification and Service Kit information.
S Certain ARO “Smart Parts” are indicated which should be available
for fast repair and reduction of down time.
S Service kits are divided to service two separate diaphragm pump
functions: 1. AIR SECTION, 2. FLUID SECTION. The FLUID SEC-
TION is divided further to match typical part MATERIAL OPTIONS.
AIR AND LUBE REQUIREMENTS
WARNING EXCESSIVE AIR PRESSURE. Can cause pump
damage, personal injury or property damage.
S Afiltercapableoffilteringoutparticleslargerthan50micronsshould
beusedontheairsupply. Thereisnolubricationrequiredotherthan
the “O” ring lubricant which is applied during assembly or repair.
S Iflubricatedairispresent,makesurethatitiscompatiblewiththe“O”
rings and seals in the air motor section of the pump.
MAINTENANCE
S Provide a clean work surface to protect sensitive internal moving
partsfrom contamination from dirtand foreignmatter duringservice
disassembly and reassembly.
S Keep good records of service activity and include pump in preven-
tive maintenance program.
S Before disassembling, empty captured material in the outlet man-
ifold by turning the pump upside down to drain material from the
pump.
INSTALLATION
S Verify correct model / configuration prior to installation.
S Retorque all external fasteners per specifications prior to start up.
S Pumpsaretestedinwateratassembly. Flushpumpwithcompatible
fluid prior to installation.
FLUID SECTION DISASSEMBLY
S When the diaphragm pump is used in a forced-feed (flooded inlet)
situation, it is recommended that a “Check Valve” be installed at the
air inlet.
1. Remove (60) inlet manifold and (61) outlet manifold.
2. Remove (22) balls, (19 and 33) “O” rings and (21) seats.
3. Remove (15) fluid caps.
NOTE: Only PTFE diaphragm models use a primary diaphragm (7) and
a backup diaphragm (8). Refer to the auxiliary view in the Fluid Section
illustration.
4. Removethe(6)diaphragmwasher,(7)or(7/8)diaphragms,and(5)
backup washer.
NOTE: Do not scratch or mar the surface of (1) diaphragm rod.
S Material supply tubing should be at least the same diameter as the
pump inlet manifold connection.
S Material supply hose must be reinforced, non-collapsible type com-
patible with the material being pumped.
S Piping must be adequately supported. Do not use the pump to sup-
port the piping.
S Use flexible connections (such as hose) at the suction and dis-
charge. These connections should not be rigid piped and must be
compatible with the material being pumped.
FLUID SECTION REASSEMBLY
S Secure the diaphragm pump legs to a suitable surface (level and
flat) to insure against damage by vibration.
S Reassemble in reverse order. Refer to the torque requirements on
page 5.
S Clean and inspect all parts. Replace worn or damaged parts with
new parts as required.
S Pumpsthat need to besubmersedmust havebothwet and non-wet
components compatible with the material being pumped.
S Submersed pumps must have exhaust pipe above liquid level. Ex-
haust hose must be conductive and grounded.
S Lubricate (1) diaphragm rod and (144) “U” cup with LubriplateR
FML-2 grease (94276 grease packet is included in service kit).
S FormodelswithPTFEdiaphragms:Item(8)Santoprenediaphragm
is installed with the side marked “AIR SIDE” towards the pump cen-
ter body. Install the PTFE diaphragm (7) with the side marked
“FLUID SIDE” towards the (15) fluid cap.
S Flooded suction inlet pressure must not exceed 10 p.s.i.g. (0.69
bar).
S Re-check torque settings after pump has been re-started and run a
while.
S VitonR and HytrelR are trademarks of the DuPont Company S KynarR is a registered trademark of Penwalt Corp. S LoctiteR is a registered trademark of Henkel Loctite Corporation S
S SantopreneR is a registered trademark of Monsanto Company, licensed to Advanced Elastomer Systems, L.P. S LubriplateR is a registered trademark of Lubriplate Division (Fiske Brothers) S
PE10P-X-X-A0S
Page 3 of 8
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST / PE10P-X-X-A0S FLUID SECTION
FLUID SECTION SERVICE KITS (637396-XX)
L KITS INCLUDE: BALLS (see Ball Option, refer to -XX in Service Kit chart below), DIAPHRAGMS (see Diaphragm Option, refer to -XX in Service Kit
chart below), and items 19, 33, 70, 144, 175 and 180 (listed below) plus 94276 Lubriplate FML-2 grease (page 6).
MATERIAL CODE
[B] = Nitrile
[C] = Carbon Steel
[E] = E.P.R.
[H] = Hytrel
SEAT OPTIONS
PE10P-XXS-XXX-A0S
“21”
BALL OPTIONS
PE10P-XXS-XXX-A0S
L “22” (1-1/4” dia.)
[K] = PVDF (Kynar)
[MSP]= Medical Grade Santoprene
[P] = Polypropylene
[SH] = Hard Stainless Steel
[SP] = Santoprene
[SS] = Stainless Steel
[T] = PTFE
-XXX Seat
Qty [Mtl]
(4) [SH]
-XXX Ball
Qty [Mtl]
(4) [SP]
-HXX 94706
-KXX 94707-2
-PXX 94707-1
-SXX 96151
-XAX 93278-A
-XCX 93278-C
-XGX 93278-2
-XTX 93278-4
-XVX 93278-3
(4)
(4)
[K]
[P]
(4)
(4)
(4)
(4)
[H]
[B]
[T]
[V]
[V] = Viton
(4) [SS]
DIAPHRAGM OPTIONS PE10P-XXS-XXX-A0S
L Service Kit
-XX = (Ball)
-XXX -XX = (Diaphragm) Diaphragm Qty [Mtl] Diaphragm Qty [Mtl] (1/8” x 2-1/8” o.d.) Qty [Mtl] (1/8” x 1-5/8” o.d.) Qty [Mtl]
L “7”
L “8”
L “19”
L “33”
“O” Ring
“O” Ring
-XXA 637396-XA
-XXC 637396-XC
-XXG 637396-XG
-XXM 637396-XM
-XXT 637396-XT
-XXV 637396-XV
96267-A
96267-C
96267-G
96267-M
96146-T
95989-3
(2)
(2)
(2)
[SP] - - - - -
- - -
- - -
- - -
- - -
- - - 93280
(4)
(4)
(4)
(4)
(4)
(4)
[E] 93279
(4)
(4)
(4)
(4)
(4)
(4)
[E]
[V]
[B]
[E]
[T]
[V]
[H]
[B]
- - - - -
- - - - -
- - - Y327-225
- - - Y325-225
- - - 93280
[V] Y327-220
[B] Y325-220
[E] 93279
(2) [MSP] - - - - -
(2)
(2)
[T]
[V]
96145-A
- - - - -
(2) [SP] 93282
- - - - - - Y327-225
[T] 93281
[V] Y327-220
MANIFOLD / FLUID CAP MATERIAL OPTIONS PE10P-XXS-XXX-A0S
PVDF (Kynar)
Polypropylene
PE10P-AKS-
PE10P-BKS-
PE10P-FKS-
PE10P-YKS-
PE10P-APS-
PE10P-BPS-
PE10P-FPS-
PE10P-YPS-
Item Description (size)
Qty Part No.
(2) 96108-2
(2) 96105-2
[Mtl] Part No. [Mtl] Part No. [Mtl] Part No.
[Mtl] Part No. [Mtl] Part No. [Mtl]
6
Diaphragm Washer
[K] 96108-2
[K] 96105-2
[K] 96108-2
[K] 96105-2
[K] 96180-2
[K] 96179-2
[K] 96108-1
[K] 96105-1
[K] 96200-[U]
[K] 96199-[U]
[P] 96108-1
[P] 96105-1
[P] 96195-1
[P] 96194-1
[P] 96108-1
[P] 96105-1
[P] 96180-1
[P] 96179-1
[P]
[P]
[P]
[P]
15 Fluid Cap
60 Inlet Manifold
61 Outlet Manifold
(1) 96200-[Z] [K] 96195-2
(1) 96199-[Z] [K] 96194-2
Z For N.P.T.F. thread models (PE10P-AKS-XXX-A0S), use “-2”. For BSP thread models (PE10P-BKS-XXX-A0S), use “-4”.
U
For N.P.T.F. thread models (PE10P-APS-XXX-A0S), use “-1”. For BSP thread models (PE10P-BPS-XXX-A0S), use “-3”.
COMMON PARTS
Item
Description (size)
Qty Part No.
[Mtl]
Item
Description (size)
Qty Part No.
[Mtl]
[B]
L n 70 Gasket
(2) 95843
(2) 93832-3
(4) 96216
(2) Y186-49
(2) Y325-114
(8) 96292
(4) 95879
1
5
Rod
Backup Washer
(1) 95995
(2) 95990-1
(16) 95880
(20) 96163
(4) 96217
(20) 96229
(1) 96104-3
(1) 96104-4
[C]
[SS]
[SS]
[SS]
[SS]
[SS]
[P]
74 Pipe Plug (1/4 - 18 N.P.T. x 7/16”)
[K]
26 Screw (M8 x 1.25 - 6g x 30 mm)
27 Screw (M8 x 1.25 - 6g x 50 mm)
28 Washer (8.5 mm i.d.)
29 Flange Nut (M8 x 1.25 - 6h)
68 Air Cap
131 Screw (M8 x 1.25 - 6g x 100 mm)
Ln144 “U” Cup (3/16” x 1-1/8” o.d.)
Ln175 “O” Ring (3/32” x 13/16” o.d.)
Ln180 “O” Ring (2.5 mm x 12 mm o.d.)
195 Hex Flange Nut (M8 x 1.25 - 6h)
[SS]
[B]
[B]
[B]
[SS]
69 Air Cap
[P]
n Air Section Service Kit parts, see page 6.
Page 4 of 8
PE10P-X-X-A0S
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST / PE10P-X-X-A0S FLUID SECTION
3
1
5
7
8
6
61 (models PE10P-AXS-XXX-A0S
and PE10P-BXS-XXX-A0S)
9
10
61 (models PE10P-YXS-XXX-A0S)
2
4
FOR THE
AIR MOTOR SECTION
SEE PAGES 6 & 7
Torque Sequence
COLOR CODE
DIAPHRAGM
COLOR
BALL
COLOR
26 , U
MATERIAL
Hytrel
Cream
Black
Tan
Cream
Red (S)
Tan
61 (models PE10P-FXS-XXX-A0S)
Nitrile
Santoprene
Santoprene
(Backup)
PTFE
Green
N / A
68
White
Yellow (-)
(-) Dash
White
Yellow (S)
(S) Dot
A
A
131 ,x 70 k
Viton
144 k 70 k
69
27 U
7
22
19
21
33
29 ,
74 s 144 k 175 k
175 k
15
22
19
21
33
180 k 195
26 , U
1 k
5
6 ,
60 (models PE10P-FXS-XXX-A0S)
Figure 2
60 (models PE10P-YXS-XXX-A0S)
. TORQUE REQUIREMENTS ,
NOTE: DO NOT OVERTIGHTEN FASTENERS.
ALL FASTENERS ARE METRIC.
(6) Diaphragm washer, 25 - 30 ft lbs (33.9 - 40.7 Nm), lubricate
face with Lubriplate grease and apply LoctiteR 271 to
threads.
60 (models PE10P-AXS-XXX-A0S
and PE10P-BXS-XXX-A0S)
(26) Screws, 10 - 12 ft lbs (13.6 - 16.3 Nm).
(29) Nuts, 10 - 12 ft lbs (13.6 - 16.3 Nm).
(131) Screws, tighten to 11 - 14 ft lbs (14.9 - 19.0 Nm).
VIEW OF TWO PIECE PTFE DIAPHRAGM
AUXILIARY VIEW A-A
LUBRICATION / SEALANTS
k Apply Lubriplate FML-2 grease to all “O” rings, “U”
cups & mating parts.
k 180
28
x Apply Loctite 242 to threads at assembly.
U Apply anti-seize compound to threads and bolt and
nut flange heads which contact pump case when
using stainless steel fasteners.
s Apply PTFE tape to threads at assembly.
7 PTFE
Santoprene 8
Z Lubriplate FML-2 is a white food grade petroleum grease.
PE10P-X-X-A0S
Page 5 of 8
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST / PE10P-X-X-A0S AIR SECTION
n Indicates parts included in 637412 Air Section Service Kit shown below and items (70), (144), (175) and (180) shown on page 4.
AIR MOTOR PARTS
Item
Description (size)
Qty Part No.
(1) 95970
(1) 96000
(2) 96323
(1) 96170
(6) 95931
(6) 96340
(1) 96325
(1) 96171
(2) Y325-123
[Mtl]
Item
Description (size)
Qty Part No.
(2) 95845
(4) Y178-52-S
(1) 93139
(1) 94276
637308
[Mtl]
[SP]
[SS]
[P]
101 Center Body
[P]
n 176 Diaphragm (check valve)
181 Roll Pin (5/32” o.d. x 1/2” long)
201 Muffler
103 Bushing
121 Plug
[D]
[D]
n 132 Gasket
[B]
L n Lubriplate FML-2 Grease
Lubriplate Grease Packets (10)
133 Washer (M6)
134 Screw (M6 x 1 - 6g x 25 mm)
160 Air Manifold
n 166 Gasket
[SS]
[SS]
[A]
MATERIAL CODE
[D] = Acetal
[P] = Polypropylene
[A] = Aluminum
[B] = Nitrile
[SP] = Santoprene
[SS] = Stainless Steel
[B]
n 173 “O” Ring (3/32” x 1-3/8” o.d.)
[B]
K
Fluid Section Service Kit parts, see page 4.
AIR MOTOR SECTION SERVICE
AIR MOTOR SECTION DISASSEMBLY
GENERAL REASSEMBLY NOTES:
1. Remove (160) air manifold, exposing (132 and 166) gaskets and
S Air Motor Section Service is continued from Fluid Section repair.
S Inspect and replace old parts with new parts as necessary. Look for
deep scratches on surfaces, and nicks or cuts in “O” rings.
S Take precautions to prevent cutting “O” rings upon installation.
S Lubricate “O” rings with Lubriplate FML-2 grease.
S Do not over-tighten fasteners, refer to torque specification block on
view.
(176) checks.
2. Remove (121) plugs.
AIR MOTOR SECTION REASSEMBLY
1. Clean and lubricate parts not being replaced from service kit.
2. Replace (173) “O” rings and assemble (121) plugs.
3. Assemble (132 and 166) gaskets and (176) checks to (101) body.
4. Assemble (160) air manifold to (101) body, securing with (134)
screws. NOTE:Tighten(134)screwsto35-40in. lbs(4.0-4.5Nm).
S Re-torque fasteners following restart.
Page 6 of 8
PE10P-X-X-A0S
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST / PE10P-X-X-A0S AIR SECTION
166 k
121
173 k
173 k
121
160
133
U . 134
132 k
176 k
101
181
103
201
. TORQUE REQUIREMENTS ,
NOTE: DO NOT OVERTIGHTEN FASTENERS.
ALL FASTENERS ARE METRIC.
Torque (134) screw to 35 - 40 in. lbs (4.0 - 4.5 Nm).
LUBRICATION / SEALANTS
Apply Lubriplate FML-2 grease to “O” rings, “U” Cups & mating parts.
k
U Apply anti-seize compound to threads at assembly.
Figure 3
TROUBLE SHOOTING
Product discharged from exhaust outlet.
S Check for diaphragm rupture.
S Check tightness of (6) diaphragm washer.
Low output volume, erratic flow, or no flow.
S Check air supply.
S Check for plugged outlet hose.
S Check for kinked (restrictive) outlet material hose.
S Check for kinked (restrictive) or collapsed inlet material hose.
S Check for pump cavitation -- suction pipe should be sized at least as
large as the inlet thread diameter of the pump for proper flow if high
viscosity fluids are being pumped. Suction hose must be a non-col-
lapsing type, capable of pulling a high vacuum.
S Check all joints on the inlet manifolds and suction connections.
These must be air tight.
Air bubbles in product discharge.
S Check connections of suction plumbing.
S Check “O” rings between intake manifold and inlet side fluid caps.
S Check tightness of (6) diaphragm washer.
Motor blows air or stalls.
S Check (176) check valve for damage or wear.
S Check for restrictions in valve / exhaust.
S Inspectthepumpforsolidobjectslodgedinthediaphragmchamber
or the seat area.
PE10P-X-X-A0S
Page 7 of 8
Download from Www.Somanuals.com. All Manuals Search And Download.
DIMENSIONAL DATA
(Dimensions shown are for reference only, they are displayed in inches and millimeters (mm).
DIMENSIONS
A - see below
E - 9-23/32” (246.7 mm)
F - 8-5/16” (211.1 mm)
G - see below
J - 6-9/32” (159.6 mm)
K - 7/16” (11.1 mm)
L - see below
N - 7-5/8” (193.9 mm)
P - see below
S - 5-1/32” (127.6 mm)
T - 8-3/8” (212.9 mm)
U - 1-3/64” (26.6 mm)
V - 17/32” (13.3 mm)
B - 13-25/32” (349.8 mm)
C - 10-1/16” (255.3 mm)
D - 2-11/32” (59.4 mm)
Q - see below
H - 5-1/32” (127.6 mm)
M - 1/2” (12.7 mm)
R - 14-11/32” (364.0 mm)
“A”
“G”
“L”
“Q”
“P”
PE10P-AXS-, BXS-
PE10P-FXS-XXX-A0S
PE10P-YXS-XXX-A0S
14-7/32” (361.2 mm)
16-1/32” (407.3 mm)
14-7/32” (361.2 mm)
14-27/32” (376.5 mm)
16-1/32” (407.0 mm)
16” (406.3 mm)
2” (50.8 mm)
-- -- -- -- --
2-3/8” (59.7 mm)
4 - 1 / 1 6 ” (103.0 mm)
2-3/8” (59.7 mm)
6-31/32” (176.6 mm)
8-9/16” (216.9 mm)
6-31/32” (176.6 mm)
1-1/32” (25.6 mm)
E
A
V
U
F
L
1 - 11-1/2 N.P.T.F. - 1 (PE10P-AXS-XXX-A0S)
Rp 1 - 11 BS (PE10P-BXS-XXX-A0S)
P
Outlet
1/4 - 18 N.P.T.F. - 1
B
PE10P-AXS-XXX-A0S
PE10P-BXS-XXX-A0S
T
Inlet
N
G
M
D
H
J
Q
S
K
C
R
1” A.N.S.I. / DIN Flange
E
F
A
P
U
Outlet
1/4 - 18 N.P.T.F. - 1
G
PE10P-FXS-XXX-A0S
B
Inlet
T
N
D
H
J
K
M
Q
C
A
A
V
E
F
U
L
P
1” A.N.S.I. / DIN Flange
Outlet
1/4 - 18 N.P.T.F. - 1
B
PE10P-YXS-XXX-A0S
T
G
M
N
D
Inlet
H
J
Q
S
K
C
R
Figure 4
PN 97999-1090
PE10P-X-X-A0S
Page 8 of 8
Download from Www.Somanuals.com. All Manuals Search And Download.
|