TSS 3-IN-1
TOTAL SPEAKER SOLUTIONS
TSS 3-IN-1
Owner’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Tilting the Speaker
Wall-Mounting the TSS 3-IN-1 Using the Included
Wall Bracket
The customer is responsible for proper selection and use of
mounting hardware, and for correctly and safely wall-mounting
the speakers.
If needed, the enclosed stand allows you to tilt the speaker
across a wide range (i.e., upward to a maximum of 18˚ or
downward to a maximum of 7˚), as shown in Figure 3.
Important!
Do not exceed the tilt range. Doing so may cause the speaker to
fall out of its stand.
Step One
Remove the wall bracket cover by removing the four wall-bracket
screws on the ends, as shown.
Step Two
Run the speaker wire for the left, center and right channels behind
the wall bracket and out the holes in the bracket. After deciding
where to place the speaker, attach the wall bracket (in a horizontal
position) to the wall using the appropriate screws and anchors.
Wall bracket
Figure 3.
Mounting screws and
anchors not included
Step Three
Run the speaker wires out through the holes in the wall
bracket cover. Resecure in place, as shown, with the four
wall bracket screws.
3
TSS 3-IN-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Step Six
Step Four
The wall-bracket design allows for rotation of the speakers
at angles of up to 30 degrees of center. Position the speakers
so they face toward the primary listening position, before
fully tightening.
Using the included Allen wrench, remove the top and bottom
end caps of the speaker by unscrewing the single center screw
on bottom.
End cap
End cap
1/4-20 x 3/4"
Screw
Step Five
Connect the wires (see page 5). Replace the end caps while
capturing the wall bracket between parts A and B of the
end cap, securing it in place.
Wall-mount
end cap B
Wall-mount
end cap A
4
TSS 3-IN-1
Download from Www.Somanuals.com. All Manuals Search And Download.
WIRING THE SPEAKER
After placing the speaker, you are ready to connect it to your
system. First, turn off all audio system power. Use high-quality
speaker wire to make the connections. Consult the owner’s
manuals included with your amplifier or receiver for connection
and operation procedures.
ᕡ
ᕢ
Surround Modes
One channel shown.
When using the TSS 3-in-1 in a Dolby® Digital or DTS® home
theater system, make sure the receiver’s/processor’s front left,
front right and center channel speaker modes are set to“Small.”
Wiring and Polarity
–
+
The TSS 3-in-1 speaker has gold-plated terminals that can
accept bare wire.To ensure proper polarity, connect each
+ terminal on the back of the amplifier or receiver to the
respective + (red) terminal on each speaker, as shown in
Figure 4. Connect the – (black) terminals in a similar way.
See the owner’s manuals that were included with your
amplifier or receiver to confirm connection procedures.
Figure 4.This example shows how to connect bare wires to the
terminals. Banana plugs may also be inserted directly into the
rear of the connector.
ᕡ Loosen the terminals.
ᕢ Insert bare ends; tighten terminals.
Be sure to connect the left-channel wires to the left-most
terminals, the center channel wires to the middle terminals, and
the right-channel wires to the right-most terminals.
CARE OF YOUR SPEAKER SYSTEM
When needed, use a soft cloth to remove any fingerprints or
to wipe off dust. Do not use any cleaning products or polish.
Clean the grille by gentle vacuuming.
Important!
Do not reverse polarities (i.e., + to – or – to +) when making
connections. Doing so will degrade the imaging and bass
response of the home theater system.
If your TSS 3-in-1 should ever need service, please contact your
the location of a service center.
After correctly placing and wiring the TSS 3-in-1 and the rest of
your speaker system, adjust the levels for all of the channels as
recommended by the manufacturer of your receiver/processor.
5
TSS 3-IN-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
TSS 3-IN-1
Each Channel
Frequency Response
120 – 20kHz ( 3dB)
Nominal Impedance
8 Ohms
89dB
Sensitivity
(2.83V @ 1m)
Recommended Amplifier
Power Range
10 – 125 Watts
Crossover Frequency
3,500Hz; 24dB/octave
Low-Frequency Drivers
(2) 3-1/2" (89mm) MMD®,
magnetically shielded
High-Frequency Driver
3/4" (19mm) MMD,
elliptical waveguide,
magnetically shielded
Dimensions (H x W x D)
Weight
4-1/8" x 40-1/8" x 4-3/8"
(105mm x 1019mm x 111mm)
15.25 lb (6.9kg)
Infinity continually strives to update and improve existing products, as
well as create new ones.The specifications and construction details in
this and related Infinity publications are therefore subject to change
without notice.
Declaration of Conformity
We, Harman Consumer Group International
2, route de Tours
72500 Château du Loir
France
declare in own responsibility that the product described in this
owner’s manual is in compliance with technical standards:
EN 61000-6-3:2001
EN 61000-6-1:2001
Laurent Rault
Harman Consumer Group International
Château du Loir, France 5/06
6
TSS 3-IN-1
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
Download from Www.Somanuals.com. All Manuals Search And Download.
Infinity Systems, 250 Crossways Park Drive,Woodbury, NY 11797 USA (516) 674-4463 (USA only) www.infinitysystems.com
Infinity, Harman International and MMD are registered trademarks, and Total Solutions is a trademark, of Harman International Industries, Incorporated.
Dolby is a registered trademark of Dolby Laboratories. DTS is a registered trademark of DTS, Inc.
Part No. ML-TS40LCR 5/06
© 2006 Harman International Industries, Incorporated.All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
|