IDE 44
Dishwasher
Installation and use
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Is a Good Habit to Get Into
NOTICE
5.Keep detergents out of the reach of children, who must also be
kept away from the dishwasher when it is open.
6.This appliance cannot be installed outdoors, not even if the area in
which it is installed is covered by a roof; it is also very dangerous to
leave it exposed to the rain and elements.
7.Do not touch the heating element during or after a wash cycle.
8.Do not lean or sit on the door when it is open, as this could overturn
the dishwasher.
9.If the appliance malfunctions, turn off water supply to the appliance
and disconnect the plug from the wall socket. Then, consult the
section entitled, " Troubleshooting." If you cannot resolve the
problem, contact a service centre.
Carefully read the instructions contained in this manual, as they
provide important information which is essential to safe and proper
installation, use and maintenance of the appliance.
This appliance complies with the following EEC directives:
- 73/23/EEC of 19/02/73 (Low Voltage) and subsequent
modifications;
- 89/336/EEC of 03/05/89 (Electromagnetic Compatibility)
and subsequent modifications.
- 97/17/EEC Labelling
-2002/96/EC (Waste Electrical and Electronic Equipment)
1.Carefully dispose of the packing material.
2.After removing the packing, check to make sure that the appliance
is not damaged. If in doubt, contact a qualified professional.
3.The dishwasher must only be used by adults for the washing of
household dishes and cooking utensils.
10.Appliances which are no longer being used must be made
inoperable by cutting the power supply cord and removing the door
lock.
4.Fundamental rules to follow when using the appliance:
- Never touch the dishwasher when barefoot or with wet hands or
feet;
To maintain the EFFICIENCY and SAFETY of this
appliance, w e recommend:
- We discourage the use of extension cords and multiple sockets;
- During installation, the power supply cord must not be excessively
or dangerously bent or flattened;
- If the appliance is not operating properly or maintenance must
be performed, disconnect the appliance from the power supply.
l call only the Service Centers authorized
by the manufacturer
l alw ays use original Spare Parts
Close-up View (control panel)
H
R
D
A
P
E
C
A: ON-OFF button
C: Door handle
D: Cycle selection Knob
H: Display
E: "Extra drying" button
P: Delayed start select button
R: Start/Reset Button
L
H
T
G: "Extra drying" indicator light
H: Cycle phase indicator lights
L: Alphanumeric indicator
S: Low salt indicator light
T: Low rinse aid indicator light
I: Delayed start indicator light
S
I
G
EN
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Close-up View (Interior)
E
G
F
H
K
J
I
L
Upper Rack
Bottom Sprayer Arm
Salt Container Cap
Top Sprayer Arm
Rack Height Adjustor
Low er Rack
Washing Filter
Detergent and Rinse Aid Dispenser
Technical characteristics
Width
cm. 45
Depth
cm. 60
cm. 85
Height
Capacity
9 standard place settings
4,3 psi - 145 psi 30KPa÷ 1MPa (0,3 ÷10 bar)
See data plate
Mains water pressure
Power voltage
Total absorber power
Fuse
See data plate
See data plate
EN
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Salt ......
Salt
Adjusting Salt Consumption
The hardness of the water varies from place to place. If
hard water is used in the dishwasher, deposits will form on
the dishes and utensils.
The dishwasher is designed to allow for adjusting the
amount of salt consumed based
on the harness of the water
The appliance is equipped with a special softener that uses
a salt specifically designed to eliminate lime and minerals
from the water.
used. This is intended to
optimize and customize the
level of salt consumption so that
it remains at a minimum.
Your Local Water Board can
supply the degree of hardness
Loading the Salt into the Softener
Always use salt intended
for use with dishwashers.
of the water
The salt container is
in your area.
located beneath the
To adjust salt consumption, pro-
lower rack and should be
ceed as follows:
filled as follows:
1. Remove the lower rack
and then unscrew and
remove the cap from the
salt container;
2. If you are filling the
container for the first
1) Unscrew the cap from the salt container.
2) There is a ring on the container with an arrow on it (see
figure to the side), if necessary, rotate the ring in the anti-
clockwise direction from the "_" setting towards the " +"
sign, based on the hardness of the water being used.
It is recommended that adjustments be made in accord-
ance with the following schema:
time, fill it with water;
3. Place the end of the funnel (supplied) into the hole and
introduce about 2 kg of salt. It is normal for a small amount
of water to come out of the salt container.
4. Carefully screw the cap back on.
Water Hardness
The salt container should be filled up w hen the low
salt indicator light "S" flashes.
Once you have loaded the salt for the first time, it is normal
that the low salt indicator light stays on or flashes for about
5 consecutive cycles.
Salt
Autono-
consu-
Clarke
degrees
Selector
position
my
°fH
mmol/l
mption
(grams/-
cycle)
(cycles\2-
kg)
0 - 14
0 - 17
0 -1,7
/
0
/
Warning: To prevent rust from forming, we advise you to
load the salt before starting a wash cycle.
14 - 36
18 - 44 1,8 - 4,4
"-"
20
40
60
60
40
25
36 - 71 45 - 89 4,5 - 8,9
>71 > 89 > 8,9
MED
"+"
EN
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Detergent and Rinse Aid ....
Rinse Aid
Detergent
This product makes dishes sparkle more as it improves their
drying. The rinse aid container is situated on the inside of
the appliance door; you should refill it when the low rinse
aid indicator light "T" flashes.
Detergent specifically intended for use with dishwashers
must be used. The dispenser must be refilled before the
start of each wash cycle following the instructions provided
in the " Wash Cycle Table." The detergent dispenser is
located on the inside panel of the door.
Loading the Rinse Aid
To open the dispenser, turn the "C" cap in the anti-clockwise
direction and then pour in the rinse aid, making sure not to
overfill. The amount of rinse aid used for each cycle can be
regulated by turning the "F" dose adjustor, located beneath
the " C" cap, with a screwdriver. There are 6 different
settings; the normal dosage setting is 4.
Loading the detergent
To open lid "A", press button "B". The cleaning detergent
should be introduced into the two containers " C"and
"D" up to the rim.
After pouring in the detergent, replace the lid, pressing
down until it clicks.
Dishwasher detergent in tablets is now available on the
market, in which case you should place one tablet into
container "D" and replace the lid.
F
C
C
B
D
Important:
Proper dosage of the rinse aid improves drying.
If drops of water remain on the dishes or spotting occurs,
the dosage adjustor should be turned to a higher setting. If
the dishes have white streaks, turn the dosage adjustor to a
lower setting.
A
Notice: To facilitate closing the cover, remove any
excess detergent on the edges of the dispenser.
Warning
Three-in-one dishwasher tablets are now available on the market, and combine the detergent, salt and rinse aid all in one.
If the water in your area is hard or very hard, we still recommend you pour extra salt into the relevant dispenser to prevent the
formation of white streaks on your dishes or on the appliance interior.
Add rinse aid to the corresponding container only if you are dissatisfied with the results on your dishes.
In any case, please read the manufacturer's instructions provided on the packet.
If you use only these products, it is normal for the salt and rinse aid indicator lights to flash permanently after a certain number
of cycles.
EN
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading the Dishw asher
Before placing the dishes in the racks, remove the largest
scraps of food left over on your plates, you will thus avoid
blocking the filter, which would reduce the efficacy of the
wash.
If the saucepans and frying pans are very dirty, allow them to
soak before being washed.
Load examples
upper rack
low er rack
You will thus avoid having to wash them again.
To make it easier to load your dishes, pull the racks out fully.
How to use the low er rack
We recommend you place the most difficult dishes to wash
into the lower rack: saucepans, lids, soup dishes and plates
(load examples are shown in the photo).
The lower rack has tip-up sectors (see figure B), so you can
place even more saucepans and frying pans or make room
for the larger one
F i g . B
1
2
• Serving dishes and large lids: place them on the sides
of the rack.
• Saucepans, salad bow ls: must always be placed upside
down.
• Very deep dishes: place them obliquely, thus allowing
water to run down them and cleaning them better.
fig. A
The cutlery basket (Fig. A)
This basket is equipped with a grids: insert the cutlery one
by one into the slots; knives and utensils with sharp blades
or tips should be positioned with the sharp parts at the
bottom.
Position all cutlery items so that they don't touch.
Especially long utensils should be placed in the horizontal
position at the front of the upper rack.
How to Use the Upper Rack
The upper rack is designed to hold more delicate and
lighter dishware, such as glasses, coffee and tea cups
and saucers, as well as plates, small bowls and shallow
pans (as long as they are not too dirty).
fig. C
After loading the dishes, remember to check that the blades
on the sprayer arms can turn freely without knocking
against any dishes.
How to adjust the upper rack ….
The upper rack can be set in a high or low position. There
are two handles on the sides of the upper rack: use these
to adjust its height (see figure C).
EN
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning on the Appliance
First of all
You've left out a dish?
Insert the plug into the electricity socket to power the
dishwasher. Turn on the water tap completely and press ON-
OFF button "A"; the display lights up and the wash cycle
time selected on the knob will flash.
You can interrupt a wash cycle by pressing the "ON-OFF"
button, then place the forgotten dishes into the appliance,
which will start up, after approximately 10 seconds, from
where it was interrupted when you turn it back on.
Selecting and starting a w ash cycle.
There's been a pow er failure? Has the dishw asher door
been opened?
The wash cycle stops and 3 dashes appear on the display;
the cycle restarts as soon as the electricity comes back on or
when the door is shut.
• Select the desired wash cycle by turning knob " D"
clockwise from wash cycle 1 to 7 and anticlockwise from 7
to 1; the display indicates the average duration of the wash
cycle and the cycle phases it consists of (consult the wash
cycle table contained on page 8, especially when first using
the appliance).
At the end of the w ash cycle
The end of the wash cycle is indicated by two short beeps
and the word "END" flashes on the display.
• Press the Start button "R" and the wash cycle starts up,
emitting a double beep; the approximate amount of time
left until the end of the wash cycle is displayed.
Warning:
• If the time indicated at the start of the wash cycle does not
correspond to the actual duration of the cycle itself, this could
be for a number of reasons: the temperature of the inlet
water, the degree of soil, prolonged attempts by the appliance
to clean the wash filter from food residue clogging it, etc.
Press button “A” to turn the appliance off, unplug the
appliance from the electricity socket to cut off the power
supply; the power supply cable should consequently be easily
accessible.
• Turn off the water tap.
Cycle phase under w ay indicator
• Empty the lower rack first.
While the wash cycle is under way, the symbols corresponding
to the cycle phases light up in sequence.
Here are the symbols corresponding to each cycle phase:
Make sure the wash cycle has ended before removing the
dishes!
Warning: when you open the dishwasher door after the wash
cycle has just ended or is under way, take care not to scald
yourself with the hot steam.
Pre-wash
Wash
Rinses
Drying
How to set the extra drying
Cancelling and modifying a w ash cycle in progress
Premise: a wash cycle in progress can only be modified if it
hasn't been running for long.
Keep the Reset button " R" pressed for about 3 seconds:
a prolonged beep will sound, followed by three short beeps.
The cancelled cycle time will flash on the display. Turn the
knob to select a new wash cycle.
Press button "E". After a prolonged beep, indicator light
"G" lights up and the time corresponding to the wash cycle
selected on the knob will flash on the display.
Note: The time indicated on the display is extended due to
the extra drying time.
To disable the extra drying option, press the same button
and indicator light "G" will be turned off after a beep is
sounded.
This option is incompatible with the soak cycle.
EN
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting a delayed start
How to set a delayed start
Have you changed your mind?
• If you change your mind, you can set a shorter time delay:
press button "P" to select it. You need not reset the wash
cycle.
When you have loaded the dishes, you can choose when to
start your dishwasher before setting the wash cycle desired.
• Press button " P" repeatedly to postpone the start of the
wash cycle from 1 hour to 24h.
• If you press the button again, the word "OFF" is displayed
(no selection made).
Once you have made your selection, make sure the appliance
door is shut and start the wash cycle by pressing the START
button.
Symbol " I" lights up on the display and the countdown
begins.
• If you have changed your mind and wish to start the wash
cycle immediately, press button "P" until the countdown is
fully reset. Indicator light " I" will turn off and the cycle will
start at the sound of a beep.
The indicator light corresponding to the cycle phase under
way will come up on the display and the countdown to the
estimated cycle end begins.
• Once the countdown is up, the wash cycle begins and the
approximate amount of time left until the end of the wash
cycle is displayed.
Warning: if the display indicates the word "dON" when you turn
your dishwasher on, this means the demo mode is in operation. This
mode is useful for exhibitors in that it simulates the wash cycles
without actually carrying them out.
To quit this mode, keep the START/RESET button "R" pressed for
approximately 4 seconds. The word "dOF" will be displayed once
you have quit the demo mode successfully.
EN
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Wash Cycle Table
Dishw asher w ashing guarantees your dishes w ill be cleaned in a hygienic setting for
safer, cleaner results.
:DVKꢀF\FOH
GXUDWLRQ
ꢃ“ꢄꢅꢆ
PDUJLQ
ZLWKRXW
H[WUD
'HWHUJHQW
IRUꢀSUHꢁ
ZDVKꢀꢂ
ZDV K
&\FOHꢀVHOHFWLRQ
LQVWUXFWLRQV
&\FOH
&\FOHꢀGHVFULSWLRQ
5LQVHꢀ$LG
GU\LQJꢇ
Pre-wash with hot water at 40°C
Wash at 65°C
2 cold rinses
Hot rinse at 65°C
Drying.
Very dirty dishes and
pans (not to be used
for delicate items)
ꢄꢉꢅꢍ
ꢏꢈꢍ
ꢈꢂꢉꢊꢀJUꢋ
ꢉꢎꢀJUꢋ
ꢌ
ꢌ
ꢄꢇꢀ,QWHQVLYH
Normally dirty pans
and dishes. Standard
daily cycle.
Wash at 60°C.
Cold rinse
Hot rinse at 70°C
Drying.
ꢉꢇꢀ7LPHꢀꢊꢀ<RX
Environmentally-frien-
dly cycle, with low
energy consumption
levels, suitable for
normally dirty pans
and dishes.
2 pre-washes with cold water
Wash at 50°C
Hot rinse at 65°C
Drying
ꢈꢂꢉꢊꢀJUꢋ
ꢄꢊꢐꢍ
ꢊꢅꢍ
ꢄꢉꢍ
ꢌ
ꢌ
ꢈꢇꢀ(FR
Economic and fast
cycle to be used for
slightly dirty dishes.
Run cycle immediately Drying
after use.
Short wash at 47°C
Hot rinse at 65°C
ꢉꢅꢀJUꢋ
ꢊꢇꢀ5DSLGꢀ ꢀ'U\
ꢐꢇꢀ6RDN
Preliminary wash cycle
for dishes and pans
awaiting completion of
the load with the dishes
from the next meal.
Short cold wash to prevent food
from drying onto the dishes.
Special cycle to be
used for delicate
items, which are more
sensitive to high
temperatures.
Wash at 52°C
Rinse at 45°C
Hot rinse at 65°C
Drying
ꢏꢅꢍ
ꢉꢅꢀJUꢋ
ꢉꢅꢀJUꢋ
ꢌ
ꢌ
ꢑꢇꢀ&U\VWDOꢀ&DUH
Quick and economic
wash for a daily load
of dishes.
Wash at 50°C
Hot rinse at 65°C
Drying
ꢐꢐꢍ
ꢎꢇꢀ$IWHUꢀ'LQQHU
EN
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Energy Saving Tips
- Use the right amount of detergent: if you use too much
detergent, the result will not be cleaner dishes, but, rather,
a greater negative impact on the environment.
- It is important to try and run the dishwasher when it is
fully loaded in order to save on energy. In order to prevent
odors from forming and food from caking onto the dishes,
you can run the hold cycle.
- There is no utility in rinsing dishes, cookware and utensils
before placing them in the dishwasher.
- Choose the right wash cycle: the choice of cycle depends
on the type of dishware, cookware and utensils being
washed and how dirty they are.
How to Keep Your Dishw asher in Shape
When You Go on Holiday
After Every Wash
When you go on holiday, it is recommended that you run a
wash cycle with the dishwasher empty and then remove
the plug from the socket, turn off the water supply and
leave the door of the appliance slightly ajar. This will help
the seals last longer and prevent odors from forming within
the appliance.
After every wash, turn off the water supply to the appliance
and leave the door slightly ajar so that moisture and odors
are not trapped inside.
Remove the Plug
Before cleaning or performing maintenance, always remove
the plug from the socket. Do not run risks.
Moving the Appliance
If the appliance must be moved, try to keep it in the vertical
position. If absolutely necessary, it can be positioned on its
back.
No Solvents or Abrasive Cleaning Products
To clean the exterior and rubber parts of the dishwasher,
do not use solvents or abrasive cleaning products. Rather,
use only a cloth and warm soapy water.
Seals
To remove spots or stains from the surface of the interior,
use a cloth dampened with water and a little white vinegar,
or a cleaning product made specifically for dishwashers.
One of the factors that cause odors to form in the
dishwasher is food that remains trapped in the seals. Periodic
cleaning with a damp sponge will prevent this from occuring.
Disposal of old electrical appliances
The European Directive 2002/96/EC on Waste Electrical and
Electronic Equipment (WEEE), requires that old household
electrical appliances must not be disposed of in the normal
unsorted municipal waste stream. Old appliances must be
collected separately in order to optimise the recovery and
recycling of the materials they contain and reduce the impact
on human health and the environment.
The crossed out " wheeled bin" symbol on the product
reminds you of your obligation, that when you dispose of
the appliance it must be separately collected.
Consumers should contact their local authority or retailer for
information concerning the correct disposal of their old
appliance.
EN
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and Special Maintenance
The filter assembly
The dishwasher is not to be used without filters. Improper
replacement of the filters may reduce the efficiency of the
wash and even damage your dishwasher.
If you want consistent good results from your dishwasher,
you need to clean the filter assembly; this way the food
particles are removed from the wash water, allowing it to be
recirculated during the cycle, filtered perfectly. For this reason,
it is a good idea to remove the larger food particles trapped
inside the cup “C” and semi-circular filter “A” after each
wash. All you need to do is
Cleaning the Sprayer Arms
It may happen that food particle
become encrusted on the
sprayer arms and block the holes
(see "Close up view (interior)",
letters F-I). Check the sprayer
arms periodically and clean them
when needed.
rinse them under running
water; to remove these, pull
1
A
the cup handle upwards.
The entire filter assembly,
comprising a semi-circular
filter “A”, a cup “C”, and a
cylindrical filter “B” should
be cleaned thoroughly once
a month. Rotate filter “B”
B
2
C
anticlockwise to remove it. For cleaning, use a non metallic
brush.
Reassemble the three parts as shown in the figures and
reinsert the whole assembly into the dishwasher, positioning
it into its housing and pressing downwards.
Troubleshooting
It may occur that the dishwasher does not function or does not
function properly. Before calling for assistance, let us see what can
be done first: have you forgot to press one of the buttons or to
perform an essential operation?
The Dishw asher Does Not Start
Have you checked whether:
Error messages.
Your dishwasher is equipped with a safety system which is able to
detect any operating anomalies.
These anomalies or faults are signalled by several codes consisting of
letters and numbers that flash up on the display. Make a note of the
error code that appears, turn the appliance off, turn off the water
tap and call for technical assistance.
- the plug is pushed into the socket correctly;
- the power is on in the house;
Tap off alarm
- the door is closed properly;
- the ON-OFF switch is on "ON";
- the water supply is turned on.
The Dishw asher Does Not Load Water
Have you checked whether:
- the water is turned on and the hose is connected properly;
- the water supply to the house is on and has sufficient
pressure;
- the water supply hose is crimped or bent;
- the filter for the water supply hose is clogged.
The Dishes Are Not Clean
Have you put the right amount of detergent into the dispenser?
Is the wash cycle suitable for the dishes you have placed inside the
appliance?
If you have forgotten to turn on the water tap, the appliance will
remind you with a series of prolonged beeps and the wording H2O
will flash up on the display. Turn the tap on and the wash cycle will
start up after a few minutes.
If you are not there when the H2O signal appears, the appliance will
switch to alarm mode and the code "A06" will flash on the display.
Turn the appliance off at button "A", turn on the water tap and wait
approximately 20 seconds before turning the appliance back on, the
wash cycle will start up again.
Clogged filter alarm
If the appliance is blocked and the code "A05" is flashing, this means
the filter is clogged by large particles of food residue. Turn the
appliance off at the ON-OFF button, clean the filter thoroughly and
reposition it in its seat, then turn the appliance back on. The wash
cycle will start up as normal after a few seconds.
Are the filter and microfilter clean?
Can the sprayer arms turn freely?
The Dishw asher Does Not Drain
Have you checked whether:
- the drain hose is crimped or bent.
Lime Deposits or a White Film Form on the Dishes
Have you checked whether:
- the lid to the salt container is closed properly;
- the rinse aid dosage is correct.
Water load solenoid valve malfunction alarm
If the code "A02" flashes, first of all turn off the water tap to avoid
any flooding and then cut off the electricity supply and call for
assistance.
If, despite all these checks, the dishwasher still does not function
and/or the problem persists, contact the nearest authorised service
centre and provide them with the following information:
- the nature of the problem;
If the display indicates the w ord "dON" w hen you turn your
dishw asher on, this means the demo mode is in operation.
Read the instructions on pages 7.
- the model type number (Mod. ...) and the serial number (S/N ....),
which are indicated on the plate located on the side of the inner part
of the door.
Never call on unauthorised technicians and refuse to allow
parts to be installed that are not original spare parts.
EN
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Positioning the Appliance
Drain Hose Connection
Position the appliance in the desired location. The back
should rest against the wall behind it, and the sides, along
the adjacent cabinets or wall. The dishwasher is equipped
with water supply and drain hoses that can be positioned
to the right or the left to facilitate proper installation.
Fit the drain pipe into a drain
line with a minimum diameter
of 4 cm or place it over the
sink. Avoid restricting or
bending it. Use the special
plastic elbow provided (see fi-
gure) to position it in the best
possible way. The part of the
pipe marked with the letter A
should be between 40 and 100
cm above the ground.
A
Levelling the Appliance
Once the appliance is positioned, adjust the feet (screwing
them in or out) to adjust the height of the dishwasher,
making it level. In any case, the appliance should not be
inclined more than 2°.
If the appliance is level, it will help ensure proper perfor-
mance.
The pipe should not be
immersed in water.
This dishwasher model can be built under a single worktop
(please read the relevant instruction sheet).
Attention: The special plastic hose support must be solidly
fastened to the wall to prevent the drain hose from moving
and allowing water to spill outside the drain.
Anti-flooding protection
Your dishwasher is provided with a special system which
blocks the water supply in the event of leaks inside the
appliance.
Electrical Connection
After making sure that the voltage and frequency values for
the current in the home correspond to those on the rating
plate (located on the stainless steel inner door of the
appliance) and that the electrical system is sized for the
maximum voltage on the rating plate, insert the plug into
an electrical socket which is earthed properly (the earthing
of the appliance is a safety requirement mandated by law).
If the electrical socket to which the appliance must be
connected is not appropriate for the plug, replace the plug,
rather than using adpators or the like as they could cause
overheating and burns.
Cold Water Connection
This electric household appliance should be connected to
the water mains using the cold water supply hose provided
with the appliance only. Do not use a different hose. In the
event of replacements, use original spare parts only.
Connect the cold water supply hose to a threaded 3/4 (gas)
connector, and making sure that it is fastened tightly in place.
If the water pipes are new or have not been used for an
extended period of time, let the water run to make sure that
the water is clear and free of impurities. If this precaution is
not taken, there is a risk that the water inlet can get blocked
and damage the appliance.
Should the electricity supply cable be damaged, we
recommend that you only contact authorised Technical
Service Centres for the replacement.
Hot Water Connection
Caution: the dishwasher plug must be accessible so that
The water supply to the appliance can also be connected to
the house's hot water line (centralised system, heating
system), as long as it does not exceed a temperature of 60°
C.
maintenance can be done safely.
In this case, the wash cycle time will be shortened by about
15 minutes and the wash efficiency slightly reduced.
The connection must be made to the hot water line following
the same procedures as those for the connection to the cold
water line.
EN
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Connection
Electrical Connection
As the colours of the wires in the mains lead may not
correspond with the coloured markings identifying the
terminal in your plug, proceed as follows:
connect Green & Yellow wire to terminal market “E” or
coloured Green or Green & Yellow.
If your appliance is supplied with a 13 amp. fused plug it
can be plugged into a 13 amp socket for immediate use.
Before using the appliance please read the instruction below.
WARNING: THIS APPLIANCE MUST BE EARTHED.
THE FOLLOWING OPERATIONS SHOULD BE CARRIED
OUT BY A QUALIFIED ELECTRICIAN.
Connect Brown wire to terminal marked “L” or coloured
Red.
Connect Blue wire to terminal marked “N” or coloured
Black.
Replacing the fuse:
When replacing a faulty fuse, a 13 amp ASTA approved
fuse to BS 1362 should always be used, and the fuse cover
re-fitted. If the fuse cover is lost, the plug must not be used
until a replacement is obtained.
If a 13 amp plug (BS 1363) is used it must be fitted with a
13 amp fuse. A15 amp plug must be protected by a 15
amp fuse, either in the plug or adaptor or at the
distribution board.
If you are in any doubt about the electrical supply to your
machine, consult a qualified electrician before use.
Replacemente fuse covers:
If a replacement fuse cover is fitted, it must be of the correct
colours as indicated by the coloured marking or the colour
that is embossed in words on the base of the plug.
Replacements can be obtained directly from your nearest
Service Depot.
How to connect an alternative plug:
The wires in this mains lead are coloured in accordance
with the following code:
Removing the plug:
BLUE
BROWN
GREEN AND YELLOW
“NEUTRAL” (“N”)
“LIVE” (“L”)
“EARTH” (“E”)
Ifyour appliance has a non-rewireable moulded plug and
you should wish to remove it to re-route the mains cable
through partitions, units etc., please esure that either:
- the plug is replaced by a fused 13 amp re-wireable plug
bearing the BSI mark of approval
- or:
GREEN &
YELLOW
- the mains cable is wired directly into a 13 amp cable outlet,
controlled by a switch, (in compliance with BS 5733) which
is accessible without moving the appliance.
13 amp fuse
BROWN
BLUE
Disposing of the plug:
CROSS-BAR
CORD GRIP
Ensure that before disposing of the plug itself, you make
the pins unusable so that it cannot be accidentally inserted
into a socket.
Instruction for connecting cable to an altenative plug:
Important: the wires in the mains lead are coloured in
accordance with the following code:
Green & Yellow
Blue
Brown
- Earth
- Neutral
- Live
Disposing of the appliance:
When disposing of the appliance please remove the plug
by cutting the mains cable as close as possible to the plug
body and dispose of it as described above.
CAUTION:
The dishwasher plug must be accessible even when the
appliance is installed as a built-in unit so that maintenance
can be done safely.
EN
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Viale Aristide Merloni 47
60044 Fabriano (AN) Italy
Tel +39 0732 6611
Download from Www.Somanuals.com. All Manuals Search And Download.
|