DPX-U6120
DPX-U5120
DPX-MP3120
DUAL DIN SIZED CD RECEIVER
INSTRUCTION MANUAL
© 2010 Kenwood Corporation All Rights Reserved.
B64-4805-00/01 (M)
Download from Www.Somanuals.com. All Manuals Search And Download.
DSP Setup
Car Type Selection
Speaker Setting
Car Type Fine Adjustments
X’Over Setting
Audio Preset Memory
Audio Preset Recall
37
Basic Operations of remote control
Appendix
48
50
52
53
54
55
58
Accessories/ Before installation
Connecting Wires to Terminals
Installation
Log Function
Log Function recall
Log Function item lock
Deleting a Log Function item
Log Function category setting
Tuner Log Function time setting
40
42
Troubleshooting Guide
Specifications
Bluetooth Setup
Bluetooth Setting
Registering Bluetooth device
Registering PIN Code
Selecting the Bluetooth device You Wish to
Connect
Deleting a Registered Bluetooth device
Downloading the Phone Book
Adding a Voice Dialing Command
Setting a Voice Command for Category
SMS (Short Message Service)
47
Downloading the SMS
SMS (Short Message Service)
English
|
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Before use
Before using this unit for the first time
This unit is initially set on the Demonstration mode.
When using this unit for the first time, cancel the
Demonstration mode. Refer to <Canceling the
Demonstration Mode> (page 6).
About discs used with this unit
• This unit can only play the CDs with
• The following discs cannot be used:
- Discs that are not round
- Discs with coloring on the recording surface or
discs that are dirty
- Recordable/Rewritable disc that has not been
finalized (For the finalization process, refer to
your disc writing software, and your disc recorder
instruction manual.)
- 8 cm (3 inch) disc (Attempt to insert using an
adapter can cause malfunction.)
.
2WARNING
To prevent injury or fire, take the following
precautions:
• Stop the car before operating the unit.
• To prevent a short circuit, never put or leave any
metallic objects (such as coins or metal tools) inside
the unit.
Handling discs
¤
CAUTION
• Do not touch the recording surface of the disc.
• Adjust the volume so that you can hear sounds
outside the car. Driving with the volume too high
may cause an accident.
• Wipe off the dirt on the panel with a dry silicon or
soft cloth.
• Do not stick tape etc. on the disc, or use a disc with
tape stuck on it.
• Do not use any accessories for the disc.
• Do not use any solvents to clean discs. Use a dry
silicon or soft cloth.
• Clean from the center of the disc and move
outward.
Failure to observe this precaution may result in
damage to the monitor or unit.
• When removing discs from this unit, pull them out
horizontally.
• Remove the rims from the center hole and disc
edge before inserting a disc.
Condensation
When the car is air-conditioned, moisture may collect
on the laser lens. This may cause disc read errors. In
this case, remove the disc and wait for the moisture
to evaporate.
How to reset your unit
Notes
If the unit fails to operate properly, press the Reset
button. The unit returns to factory settings when the
Reset button is pressed.
• If you experience problems during installation,
consult your Kenwood dealer.
• When you purchase optional accessories, check with
your Kenwood dealer to make sure that they work
with your model and in your area.
• Characters that conform to ISO 8859-1 can be
displayed.
• To display characters in the following language,
additional setting is required.
Chinese: Refer to “Chinese” of <Initial Settings>
(page 30).
• The illustrations of the display and the panel
appearing in this manual are examples used to
explain more clearly how the controls are used.
Therefore, what appears on the display in the
illustrations may differ from what appears on the
display on the actual equipment, and some of the
illustrations on the display may be inapplicable.
Reset button
|
4
DPX-U6120/ DPX-U5120/ DPX-MP3120
Download from Www.Somanuals.com. All Manuals Search And Download.
Component names and functions
2
1
3
t
r
e
4
5
q p
8
7 6
w
9
1 Disc slot
p
DPX-U6120 DPX-U5120
[iPod] button
Select the iPod source.
When inserted a disc (label side up), the source is
switched automatically and a song starts playing.
2 [0] button
To eject the disc.
3 [1] – [6] button
DPX-MP3120
[38] button
To start or interrupt playback for CD and Audio
file.
Mute the volume. (During Tuner, AUX source)
4] / [¢] button
To select a station, song and setting items.
To recall the memorized station.
Switches the play mode between music discs,
Audio files, and iPod.
q [
4 [DISP] button
To change the display mode.
w [BAND] button
5 [ATT] button
Turning the volume down quickly.
6 [ ] button
To select the receiving band, and the folder for
Audio file.
e [SRC] button
To enter the music search mode.
7 [ ] button
To return to previous item.
8 [VOL] knob
To turn on this unit and select the Source.
To turn off this unit (press the button at least 1
second).
r Auxiliary Input Terminal
Portable audio device can be connected with the
mini-plug (3.5 mm ø).
To adjust volume.
Enters function setting mode and setting item
(turn and press the knob). Refer to <Function
setting Operation> (page 7) for details.
• Use the mini-plug cable which is stereo type and does
not have any resistance.
t
DPX-U6120 DPX-U5120
9
DPX-U6120
USB Terminal
When connecting, open up the USB terminal lid. A
USB device or an iPod can be connected.
[LOG] button
To display a Log Function list
DPX-U5120 DPX-MP3120
[B.BOOST] button
To boost the bass tone in two steps (LV1, LV2,
OFF).
English
|
5
Download from Www.Somanuals.com. All Manuals Search And Download.
General operation
Adjusting the Clock
DPX-U6120
1
2
Press the [VOL] knob to enter the Function
setting mode.
SRC
The item can be selected and determined as
follows.
”Settings” ➜ “Clock & Date” ➜ “Clock Adjust”
To select the item, turn the [VOL] knob. To
determine the item, press the [VOL] knob.
DPX-U6120
DPX-U5120
iPod
VOL
Before Using
3
4
5
6
Press [4] or [¢] button to select hour or
minute to set.
Canceling the Demonstration Mode
Cancel the demonstration mode when you use it for
the first time after installation.
Turn the [VOL] knob to adjust the hour and
minute.
Press the [VOL] knob to finish the Clock
adjusting.
1
2
Press the [VOL] knob to cancel the demonstration
mode when the messages “To cancel DEMO
press the volume knob”/ “CANCEL DEMO PRESS
VOLUME KNOB” are displayed (approx. 15
seconds).
Press the [
] knob for at least 1 second, and
then press it again briefly to exit the Function
setting mode.
Turn the [VOL] knob to select “YES” and press the
[VOL] knob.
DPX-U5120 DPX-MP3120
1
2
Press the [B.BOOST] button for at least 1 second.
⁄
Turn the [VOL] knob to adjust the hour, and then
press the [VOL] knob.
• Demonstration mode can also be cancelled in “DEMO
Mode” of Function setting mode. Refer to <Demonstration
mode Setting> (page 31).
3
Turn the [VOL] knob to adjust the minute, and
then press the [VOL] knob.
|
6
DPX-U6120/ DPX-U5120/ DPX-MP3120
Download from Www.Somanuals.com. All Manuals Search And Download.
Common Operation
Function setting Operation
The basic operating procedure for using this
function is described below. The individual function
items are covered in the operating procedures.
Power and source select
Turns the power ON by pressing the [SRC]
button.
1
Select the source
Press the [SRC] button.
Function items vary from source to source.
When the power is ON, select a source.
Press the [SRC] button each time switches
between sources.
Tuner (“TUNER”) ➜ USB (“USB”) or iPod (“iPod”)
(DPX-U6120/ DPX-U5120 only) ➜ CD (“CD”) ➜
Auxiliary input (“AUX”) ➜ Standby (“STDBY”/
“STANDBY”) ➜ Tuner...
2
3
Enter Function setting mode
Press the [VOL] knob.
Select the setting item
Turn the [VOL] knob and press it when the
desired item is displayed.
DPX-U6120 DPX-U5120
Repeat the operation until your desired setup item
is selected.
Operation example:
Press the [iPod] button to switch the source to
iPod.
Press the [SRC] button for at least 1 second to
turns the power OFF.
4
3
1[VOL]
3[
]
2
⁄
Settings
Exit
Seek Mode
• The SRC Select mode can be set in “Source Select” of <Initial
Settings> (page 30). (DPX-U6120 only)
1
1
• When an optional accessory is connected, the source name
for each device appears. (DPX-U6120 only)
• When connection of the iPod is recognized, the source
display changes from “USB” to “iPod”.
[VOL]
[
]
2
4
Auto Memory
Audio Control
1 sec.
Volume
In this manual, the above selection is indicated as
Select “Settings”/ “SETTINGS” >“Seek Mode”/
“SEEK MODE”.
Turning the [VOL] knob adjusts the sound
volume.
4
5
Make a setting
Turn the [VOL] knob to select a setting value,
and then press the [VOL] knob.
Exit Function setting mode
Press the [ ] button for at least 1 second.
English
|
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Function of DPX-U6120/ DPX-U5120
iPod/iPhone Operation
3
Select a song
Operation type
Move between items
Select an item
Skip Search
Return to previous item
Operation
1 – 6
Turn the [VOL] knob.
Press the [VOL] knob.
Press the [4] or [¢] button.
Press the [ ] button.
SRC
✍ For example: Searching by Artist name.
Turn the [VOL] knob and press it when the
desired item is displayed.
4 ¢
iPod
VOL
Select “Artists”/ ”ARTISTS” > Artist name > Album
name > Song title
Basic Operation
Cancelling Enter Music search mode
Press the [ ] button for at least 1 second.
Playing iPod
• Connect an iPod
When connected, the source is switched
⁄
• Characters which cannot be displayed are left blank. If non
of the characters can be displayed, the browse item name
and digits are displayed.
automatically and a song starts playing.
• Select iPod source
Press the [iPod] button.
Items
Playlists
Artists
Albums
Songs
Display
“PLIST***” Podcasts
“ART***”
“ALB***”
“PRGM***”
Items
Display
“PDCT***”
“GEN***”
“COM***”
⁄
Genres
Composers
• KCA-iP101/iP102 (optional accessory) is recommended to
connect an iPod.
Song Select
Press the [4] or [¢] button.
•
Set the ratio with “Skip Search” in <iPod Setting> (page 9).
Fast Forwards or Fast Backwards
Hold down the [4] or [¢] button.
Play function
Repeat play
Press the [4] button.
Switches between Repeat (“File Repeat ON”/ “FILE
REPEAT”) and off (“File Repeat OFF”/ “REPEAT OFF”)
when pressed.
Pause and Play
Press the [6] button to pause or resume
playback.
Remove iPod
1
Select a source other than the iPod
Press the [SRC] button.
Random play
Press the [3] button.
Randomly plays the music.
2
Remove the iPod.
Pressing the button toggles the setting between
Random play on (“Folder Random ON”/ “FOLDER
RANDOM”) and off (“Folder Random OFF”/
“RANDOM OFF”).
⁄
• Removing the iPod with it selected as a source can damage
the data stored in the iPod.
Press this button again cancels the Random play.
Selecting a song by browsing iPod
All Random play
Searching for the song you want to play.
Press the [3] button for at least 1 second.
All songs in iPod are played at random.
Pressing the button toggles the setting between All
random play on (“All Random ON”/ “ALL RANDOM”)
and off (“All Random OFF”/ “RANDOM OFF”).
Press this button again cancels the All Random
play.
1
2
Select iPod source
Press the [iPod] button.
Enter Music search mode
Press the [ ] button.
|
8
DPX-U6120/ DPX-U5120/ DPX-MP3120
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Exit Function setting mode
Press the [ ] button for at least 1 second.
⁄
• The time required to turn on the all random function may
become longer depending on the number of songs in iPod.
• Turning on the all random function changes the iPod
browse item to “Songs”. This browse item will not be
⁄
• The setting of “Skip Search” in <iPod Setting> (page 9)
and that in <USB Setting> (page 14) are always the same.
Changing the setting of one reflects the other.
changed even if the all random function is turned off.
• If the browse item is changed to search for music while the
all random function is on, the all random function is turned
off and the songs in the browse item are played at random.
Selecting the Search mode
You can select the most suited search method
for the desired song from 4 types of the Search
mode.
iPod Control by Hand Mode
Allowing you to operate iPod with the control on the
iPod.
Press the [iPod] button for at least 1 second.
When the iPod control by hand mode is selected,
“iPod by Hand Mode”/”HANDS ON” is displayed.
Search mode Operation Overview
“Related Search”/ Press the Searches for music of the same artist or
“RELATED SRCH” [1] button. genre as the one being played.
Refer to the <Related Search>
(page 10).
⁄
“Direct Search” Press the You can quickly search the desired song
[2] button. by specifying its Search item (artist,
album, etc.) and initial.
• In the iPod Control by hand mode, iPod cannot be operated
using this unit.
• This mode is not compatible with music information display.
The display will show “iPod by Hand Mode”/ “iPod MODE”.
• iPod can be operated when it conforms to the iPod control
function.
Function of DPX-U6120.
Refer to <Direct Search> (page 10).
“Alphabet
Search”/
“ALPHABET
SRCH”
Press the You can select an alphabetic character
[3] button. from the list in the Search item (artist,
album, etc.) selected now.
Refer to <Alphabet Search> (page 11).
Press the Registers a song to My Playlist.
iPod Setting
“Register My
You can select the following iPod Setting items.
Playlist”/“Recall [5] button. Refer to <My Playlist> (page 12).
My Playlist”/“MY
PLAYLIST”
1
Select iPod source
Press the [iPod] button.
1
2
3
Select iPod source
Press the [iPod] button.
2
3
Enter Function setting mode
Press the [VOL] knob.
Enter Music search mode
Press the [ ] button.
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Settings”/ “SETTINGS”.
Select the Search mode
Press the [1]/ [2]/ [3]/ [5] button.
4
Select the setting item
Turn the [VOL] knob and press it when the
Cancelling Music search mode
desired item is displayed.
Press the [ ] button for at least 1 second.
Display
Overview
“Settings”/
“SETTINGS”
“Skip Search”/ Sets the ratio of skip performed with <Skip
“SKIP SEARCH” Search> (page 8).
“0.5%”/ “1%”/ “5%”/ “10%”
“Delete My
Deletes the registered My Playlist.
Playlist”/“MPLIST Refer to <Deleting a Song from the Playlist>
DELETE”
(page 12) for the operation.
(
: Factory setting)
5
Make a setting
Turn the [VOL] knob to select a setting value,
and then press the [VOL] knob.
English
|
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Function of DPX-U6120/ DPX-U5120
iPod/iPhone Operation
Function of DPX-U6120
Related Search
Direct Search
Searches for music of the same artist or genre as the
one being played.
You can quickly search the desired song by
specifying its Search item (artist, album, etc.) and
initial.
1
2
3
4
Select iPod source
Press the [iPod] button.
1
2
3
4
Select iPod source
Press the [iPod] button.
Enter Music search mode
Press the [ ] button.
Enter Music search mode
Press the [ ] button.
Enter Related search mode
Press the [1] button.
Enter Direct Search mode
Press the [2] button.
Select the Search item
Turn the [VOL] knob and press it when the
desired Search item is selected.
Select the Search item
Turn the [VOL] knob and press it when the
Display
Searches music
desired Search item is selected.
“Search Artist”/
“SRCH ARTIST”
Displays the album of the same artist.
Display
“PLAY LIST”
“ARTIST”
“ALBUM”
“SONG”
Items
Playlists
Artists
Albums
Songs
Display
“PODCAST”
“GENRE”
Items
Podcasts
Genres
“Search Album”/ Displays music in the album in which the one
“SRCH ALBUM”
“Search Genre”/
“SRCH GENRE”
being played is included.
Displays the artist of the same genre.
“COMPOSER”
Composers
“Search Composer”/ Displays the album including music created by the
“SRCH COMPOSER” same Composer.
5
6
Select the character to be searched for
After this step, you need to browse. See step 3 of
<Selecting a song by browsing iPod> (page 8) to
select a song.
Operation type
Move between items
Select an item
Operation
Turn the [VOL] knob.
Press the [VOL] knob.
Press the [4] or [¢] button.
Move to the next column
Cancelling the Related search
Press the [ ] button for at least 1 second.
Up to 3 characters can be entered.
⁄
Determine the selected initial
Turn the [VOL] knob and press it when the
desired item is displayed.
• Related search cannot be performed while playing the
Podcast.
• When the music being played has no information on
browsing items or no music was found, “Not Found”/ “NOT
FOUND” is displayed.
Select “DONE”.
Start search. When search is completed, the music
search mode is selected again at the selected
character position.
After this step, you need to browse. See step 4 of
<Selecting a song by browsing iPod> (page 8) to
select a song.
Cancelling the Direct Search
Press the [ ] button for at least 1 second.
⁄
• Characters that can be entered are alphabetical characters
(A to Z), numerical characters(0 to 9), and “ * ”.
• “ * ” indicates characters other than alphabetical and
numerical characters. You cannot enter any more characters
when entering “ * ” in the first character position.
• If the first character string begins with an article “a”, “an”, or
“the” in the Direct Search mode, it is searched for in defiance
of the article.
|
10 DPX-U6120/ DPX-U5120/ DPX-MP3120
Download from Www.Somanuals.com. All Manuals Search And Download.
Alphabet Search
You can select a song by alphabet. This function
searches songs whose name contain the specified
character(s) in the list of the selected Search item
(artist, album, etc).
1
2
3
Select iPod source
Press the [iPod] button.
Enter Music search mode
Press the [ ] button.
Select search item
Turn the [VOL] knob and press it when the
desired item is displayed.
Select the item (artist, album, etc.) you want to
search.
4
5
Enter Alphabet Search mode
Press the [3] button.
Search for song
DPX-U6120
Operation type
Select the character
Select an item
Operation
Turn the [VOL] knob.
Press the [VOL] knob.
DPX-U5120
Operation type
Select the character
Move the cursor to the
enter character position
Determine the selected
character
Operation
Turn the [VOL] knob.
Press the [4] or [¢] button.
Press the [VOL] knob.
Cancelling the Alphabet Search
Press the [ ] button for at least 1 second.
⁄
• The time of search by alphabet may become long
depending on the number of songs or items in iPod.
• If the first character string begins with an article “a”, “an”,
or “the” in the Alphabet Search mode, it is searched for in
defiance of the article.
English
|
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Function of DPX-U6120/ DPX-U5120
iPod/iPhone Operation
4
Turn the [VOL] knob to select “YES”, and then
press the [VOL] knob.
“Completed”/ “COMPLETED” is displayed.
My Playlist
Allows you to register your favorite songs in the
Playlist of this unit. You can register up to 10 songs
in the Playlist.
Deleting the all song from the Playlist (In
Function setting mode)
Registering Songs in the Playlist
1
Enter Function setting mode
Press the [VOL] knob.
1
2
Play the song you want to register
Register the song
2
Enter Delete Playlist mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Settings”/ “SETTINGS” > “Delete My
Playlist”/ “MPLIST DELETE”.
Press the [5] button for at least 2 second.
“## Stored”/ “## STORED” (Registration number) is
displayed.
⁄
• Make a Playlist from the songs stored in one iPod. If you
attempt to register a song stored in a different iPod, ”No
Information”/ “NO INFO” appears and then ”Delete My
Playlist All Delete?”/ “MPLIST DELETE” appears. Select “YES” to
delete the Playlist when you want to remake it.
• If you attempt to register the eleventh song, ”Memory
Full”/ ”MEMORY FULL” appears and you cannot register it
accordingly. To register the song, delete an unnecessary
song.
3
Turn the [VOL] knob to select “YES”, and then
press the [VOL] knob.
“Completed”/ “COMPLETED” is displayed.
⁄
• If you connect the different iPod from one registered to
My Playlist, “Delete One”/ “DELETE ONE” and “Delete All”/
“DELETE ALL” will not appear and all songs be deleted.
• Do not register Podcasts. Songs you do not want to register
may be registered, or playback may not be carried out
correctly.
Playing the Song in the Playlist
1
Enter Playlist mode
Press the [5] button.
2
Play the song in the Playlist
Turn the [VOL] knob and press it when the
desired item is displayed.
Select the song you want to play.
⁄
• Turning ACC OFF or the power OFF cancels the My Playlist
mode.
• The ending of a song may be cut unless the song has a
silence of 1 second or longer at the end.
• Random play cannot be performed during playback of a
song in the Playlist.
Deleting a Song from the Playlist
1
2
3
Enter Playlist mode
Press the [5] button.
Enter Delete Playlist mode
Press the [VOL] knob for at least 1 second.
Select Delete Playlist mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select ”Delete One”/ “DELETE ONE” or ”Delete
All”/ “DELETE ALL”.
|
12 DPX-U6120/ DPX-U5120/ DPX-MP3120
Download from Www.Somanuals.com. All Manuals Search And Download.
Function of DPX-U6120/ DPX-U5120
USB device Operation
File Search
Selecting the file you want to listen to from the
device being played now.
2 – 6
1
Select USB source
Press the [SRC] button.
SRC
Select the “USB” display.
2
3
Enter Music search mode
Press the [ ] button.
4 ¢
BAND
VOL
Select a file
Basic Operation
Operation type
Move between items
Select an item
Operation
Turn the [VOL] knob.
Press the [VOL] knob.
Playing USB device
• Connect a USB device
When connected, the source is switched
Skip Search (Function of Music Press the [4] or [¢] button.
Editor media)
automatically and a song starts playing.
Return to previous item
Press the [ ] button.
✍ For example: Searching for ¡".
Turn the [VOL] knob and press it when the
desired item is displayed.
• Select USB source
Press the [SRC] button.
Select the “USB” display.
Select “Music” > 1 > 2 > ¡"
⁄
• CA-U1EX (optional accessory) is recommended to connect
1
2
a USB device.
¡"
¡!
¡#
Moving to the next folder
Press the [BAND] button.
Cancelling Music search mode
⁄
Press the [ ] button for at least 1 second.
• The Music Editor media does not allow you to select a
⁄
folder.
• Set the ratio with “Skip Search” in <USB Setting> (page 14).
Song Select
Press the [4] or [¢] button.
Fast Forwards or Fast Backwards
Hold down the [4] or [¢] button.
⁄
• No sound is output while playing Audio file
Pause and Play
Press the [6] button to pause or resume
playback.
Remove USB device
1
Select a source other than the USB
Press the [SRC] button.
2
Remove the USB device.
⁄
• Removing the USB device with it selected as a source can
damage the data stored in the USB device.
English
|
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Function of DPX-U6120/ DPX-U5120
USB device Operation
Play function
USB Setting
You can select the following USB Setting items.
Scan play
Press the [2] button.
Successively plays the intro of the music in the
1
Select USB source
Press the [SRC] button.
folder.
Select the “USB” display.
When Scan Play is turned on, “File Scan ON”/ “FILE
SCAN” is displayed.
Pressing this button again plays songs in the
normal mode starting with the song being played
now.
2
3
Enter Function setting mode
Press the [VOL] knob.
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Settings”/ “SETTINGS”.
Random play
Press the [3] button.
Randomly plays the music in the folder.
When Random Play is turned on, “Folder Random
ON”/ “FOLDER RANDOM” is displayed.
Press this button again cancels the Random play.
4
Select the setting item
Turn the [VOL] knob and press it when the
desired item is displayed.
Display
Overview
“Settings”/
“SETTINGS”
Repeat play
Press the [4] button.
Switches between File Repeat (“File Repeat ON”/
“FILE REPEAT”), Folder Repeat (“Folder Repeat ON”/
“FOLDER REPEAT”), and OFF (“Folder Repeat OFF”/
“REPEAT OFF”) when pressed.
“Skip Search”/ Sets the ratio of skip performed with <Skip
“SKIP SEARCH” Search (Function of Music Editor media)>
(page 13).
“0.5%”/ “1%”/ “5%”/ “10%”
(
: Factory setting)
5
6
Make a setting
Turn the [VOL] knob to select a setting value,
and then press the [VOL] knob.
⁄
• The Music Editor media does not allow you select folder
Exit Function setting mode
Press the [ ] button for at least 1 second.
repeat play.
⁄
• The setting of “Skip Search” in <iPod Setting> (page 9)
and that in <USB Setting> (page 14) are always the same.
Changing the setting of one reflects the other.
|
14 DPX-U6120/ DPX-U5120/ DPX-MP3120
Download from Www.Somanuals.com. All Manuals Search And Download.
Music CD/ Audio file Operation
DPX-MP3120
38
Function of Internal CD source
0
Music Search
Selecting the music you want to listen to from the
disc being played now.
2 – 6
1
Select CD source
Press the [SRC] button.
Select the “CD” display.
SRC
2
3
Enter Music search mode
Press the [ ] button.
4 ¢
BAND
VOL
Search for music
Basic Operation
Operation type
Move between items
Select an item
Operation
Turn the [VOL] knob.
Press the [VOL] knob.
Press the [ ] button.
Disc play
• Insert a disc.
When inserted, the source is switched
Return to previous item
automatically and a song is starts playing.
When a CD is inserted, the “IN” indicator is ON.
Cancelling Function setting mode
Press the [ ] button for at least 1 second.
• Select CD source
Press the [SRC] button.
Select the “CD” display.
Play function
Scan play
Press the [2] button.
Successively plays the intro of the music in the disc
Disc ejection
Press the [0] button.
or folder.
Moving to the next folder
When Scan Play is turned on, “Track Scan ON”/
“TRACK SCAN”/ “File Scan ON”/ “FILE SCAN” is
displayed.
Pressing this button again plays songs in the
normal mode starting with the song being played
now.
Press the [BAND] button.
⁄
• This operation can be performed only for the Audio file.
Song Select
Press the [4] or [¢] button.
Fast Forwards or Fast Backwards
Hold down the [4] or [¢] button.
Random play
Press the [3] button.
Randomly plays the music in the disc or folder.
When Random Play is turned on, “Disc Random
ON”/ “DISC RANDOM”/ “Folder Random ON”/
“FOLDER RANDOM” is displayed.
⁄
• No sound is output while playing Audio file.
Pause and Play
DPX-U6120 DPX-U5120
Press this button again cancels the Random play.
Press the [6] button to pause or resume
playback.
Repeat play
Press the [4] button.
DPX-MP3120
Switches between Track Repeat (“Track Repeat ON”/
“TRACK REPEAT”) and OFF (“Track Repeat OFF”/
“REPEAT OFF”) when pressed while playing a CD.
Switches between File Repeat (“File Repeat ON”/
“FILE REPEAT”), Folder Repeat (“Folder Repeat ON”/
“FOLDER REPEAT”), and OFF (“Folder Repeat OFF”/
“REPEAT OFF”) when pressed while playing an
Audio file.
Press the [38] button to pause or resume
playback.
English
|
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Music CD/ Audio file Operation
Function of DPX-U6120
Function of DPX-U6120 with disc changer and
remote control
Basic Operation of Disc Changer
(Optional)
Direct search in Disc changer
(Optional)
Select CD changer source
Press the [SRC] button.
Select the “CD CH” display.
Searching the disc or music by entering the disc or
music number.
1 Enter Direct search mode
Press the [DIRECT] button on the remote
control.
Moving to the next disc
Press the [BAND] button.
Song Select
Press the [4] or [¢] button.
“– –” is displayed.
2 Enter the disc or music number
Press the number buttons on the remote
control.
Fast Forwards or Fast Backwards
Hold down the [4] or [¢] button.
Pause and Play
Press the [6] button to pause or resume
playback.
3 Search the disc
Press the [FM] or [AM] button on the remote
control.
Playing the Current Song or Disc Repeatedly.
(Repeat play)
Press the [4] button.
Switches between Track Repeat play on (“Track
Repeat ON”), Disc Repeat play on (“Disc Repeat
ON”), and Repeat play off (“Repeat OFF”) when
pressed.
4 Search the music
Press the [4] or [¢] button on the remote
control.
Cancelling Direct search
Press the [
] button on the remote control.
⁄
• Input “0” to select disc 10.
Randomly plays the music in the disc changer.
(Magazine random play)
Press the [5] button.
When Magazine random play is turned on,
“Magazine Random ON” is displayed.
Press this button again cancels the Magazine
random play.
Function of remote control
Direct music search
Searching the music by entering the track number.
1 Enter Direct Music search mode
Press the [DIRECT] button on the remote
control.
“– –” is displayed.
2 Enter the music number
Press the number buttons on the remote
control.
3 Search the music
Press the [4] or [¢] button on the remote
control.
Cancelling Direct music search
Press the [
] button on the remote control.
|
16 DPX-U6120/ DPX-U5120/ DPX-MP3120
Download from Www.Somanuals.com. All Manuals Search And Download.
Tuner Operation
“Auto Memory”/ Memorizes 6 stations with good reception
“AUTO MEMORY” automatically.
Refer to <Auto Memory Entry> (page 17).
“Forced MONO”/ Reduces the noise when stereo broadcasts are
“FORCED MONO” received as monaural.
“ON”/ “OFF”
1 – 6
SRC
(
: Factory setting)
5
6
Make a setting
Turn the [VOL] knob.
4 ¢
BAND
VOL
Exit Function setting mode
Press the [ ] button for at least 1 second.
Basic Operation
Remarks
• Forced MONO
Selecting Tuner source
Press the [SRC] button.
Select the “TUNER” display.
Strong electrical fields (such as from power lines) may
cause unstable sound quality when it is set to ON. In such
a situation, turn it OFF.
Selecting the Receiving Band
Press the [BAND] button.
Pressing the button switches the receiving band
(FM1, FM2, FM3, AM).
Station Preset Memory
Putting a station in the memory.
1
2
Select the frequency to put in the memory
Press the [4] or [¢] button.
Selecting the Receiving station
Press the [4] or [¢] button.
✍ Details of the station selecting in operation are
set in the “Seek Mode”/ “SEEK MODE” of <Tuner
Setting> (page 17).
Select the number to put in the memory
Press the [1] – [6] button for at least 2 seconds.
⁄
• Up to 6 stations with a different band (FM/AM) can be
memorized to the [1] – [6] button according to the setting
of “Tuner Preset Type”/ “PRESET TYPE” of <Initial Settings>
(page 30).
Tuner Setting
You can select the following Tuner Setting items.
1
Select Tuner source
Press the [SRC] button.
Select the “TUNER” display.
Auto Memory Entry
Putting stations with good reception in the memory
automatically.
2
3
Enter Function setting mode
Press the [VOL] knob.
Turn the [VOL] knob and press it when the desired
item is displayed.
Select “Settings”/ “SETTINGS”.
1
2
3
Select the radio band you wish to store in the
preset memory
Enter Function setting mode
Press the [VOL] knob.
4
Select the setting item to adjust
Turn the [VOL] knob and press it when the desired
item is displayed.
Enter Auto Memory Entry mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Display
Overview
“Settings”/
“SETTINGS”
Select “Settings”/ “SETTINGS” > “Auto
Memory”/ “AUTO MEMORY”.
“Seek Mode”/ Selects the tuning mode of the radio.
“SEEK MODE”
“Auto1”/ “AUTO1”: Automatic search for a
4
Open Auto Memory Entry
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “YES”.
station.
“Auto2”/ “AUTO2”: Search in order of the
stations in the Preset memory.
“Manual”/ “MANUAL”: Normal manual
tuning control.
When 6 stations that can be received are put in the
memory, auto memory entry closes.
English
|
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Tuner Operation
Preset Tuning
Frequency Step Setting
Recalling the stations in the memory.
Changing the tuning frequency step.
The original setting is FM band 50 kHz, and AM
band 9 kHz.
1
2
Select the radio band
Recalls the memorized station
Press the [1] – [6] button.
1 Turn the power OFF
Press the [SRC] button for at least 1 second.
Function of remote control
2 Switch the frequency step
While pressing the [1] and [5] buttons, press the
[SRC] button.
Direct access tuning
Entering the frequency and tuning.
Release your fingers from the button after the
1 Enter Direct access tuning mode
Press the [DIRECT] button on the remote
control.
display appears.
The frequency step changes to FM band 200 kHz,
and AM band 10 kHz.
“– – – –” is displayed.
⁄
2 Enter the frequency
• When the same operation is repeated, the frequency step
returns to the original setting.
Press the number buttons on the remote
• When the frequency step is changed, the frequencies in the
memory are deleted.
control.
Example:
Desired frequency Press button
92.1 MHz (FM)
810 kHz (AM)
[9], [2], [1]
[8], [1], [0]
3 Search the frequency
Press the [4] or [¢] button on the remote
control.
Cancelling Direct access tuning
Press the [
] button on the remote control.
|
18 DPX-U6120/ DPX-U5120/ DPX-MP3120
Download from Www.Somanuals.com. All Manuals Search And Download.
Function of DPX-U6120 with KCA-BT200/BT300 (Optional Accessory)
Bluetooth Audio Operation
Basic Operation
Selecting Bluetooth Audio source
Press the [SRC] button.
Select the “BT Audio” display.
6
SRC
Pause and play
Press the [6] button.
4 ¢
Music Search
Press the [4] or [¢] button.
⁄
Connecting a Bluetooth Device
• All or some of the operations above cannot be performed if
the Bluetooth audio player is not ready for remote control.
• Switching between Bluetooth audio sources does not start
or stop playback automatically. Perform the operation for
starting or stopping playback.
• Some audio players cannot be controlled remotely or
reconnected after Bluetooth disconnection. Operate the
main unit of the audio player to connect Bluetooth.
Before use the Bluetooth device, you need to
connect Bluetooth device to this unit.
Pairing (Registering from Bluetooth devices)
To make your Bluetooth Audio player usable with
this unit, you need to register it (pairing).
1
Turn on this unit
Press the [SRC] button.
2
Start registering this unit by operating the
Bluetooth device
By operating the Bluetooth device, register the
audio player (pairing). Select “KCA-BT200”/ “KCA-
BT300” from the list of connected units.
3
4
Enter a PIN code
Input the PIN code (“0000”) in the Bluetooth
device.
Check that registration is complete on the
Bluetooth device.
✍ PIN code is set to “0000” as the default. You can
change this code. Refer to <Registering PIN
Code> (page 44).
By operating the Bluetooth device, start
Bluetooth connection.
⁄
• If pairing does not succeed, try followings.
– PIN code is set to “0000”. See <Registering PIN Code>
(page 44)
– Turn off the power of this unit and turn it back on. And
then try the pairing operation again.
– If other audio players have been registered, delete them.
And then try the pairing operation again. See <Deleting a
Registered Bluetooth device> (page 45)
• When registering from this unit, refer to <Registering
Bluetooth device> (page 43).
English
|
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Function of DPX-U6120 with KCA-BT200/BT300 (Optional Accessory)
Operation of hands-free phoning
⁄
• When registering from this unit, refer to <Registering
1 – 6
Bluetooth device> (page 43).
Receiving a Call
DISP
ATT
SRC
Answering a Phone Call
Press the [VOL] knob.
4 ¢
LOG VOL
⁄
• The following operations disconnect the line:
- Insert a CD.
Connecting a Bluetooth Device
- Connect a USB device.
• The name of the calling party is displayed if it has already
been registered in the Phone Book.
Before use the Bluetooth device, you need to
connect Bluetooth device to this unit. The following
3 steps procedure is necessary.
Rejecting an Incoming Call
Step 1. Pairing (Registering from Bluetooth
devices)
Press the [SRC] button.
To make your Bluetooth device (cell-phone) usable
with this unit, you need to register it (pairing).
During a Call
Disconnecting a Call
Press the [SRC] button.
1
2
Turn on this unit
Press the [SRC] button.
Switching to the Private Mode
Press the [6] button.
Switches between Private talk (“PRIVATE”) and
Start registering a this unit by operating the
Bluetooth device
By operating the Bluetooth device, register the
hands-free unit (pairing). Select “KCA-BT200”/ “KCA-
BT300” from the list of connected units.
Hands-free talk each time this button is pressed.
⁄
• Depending on the type of your cell-phone, switching
to the private talk mode may select the source that was
used before commencing the hands-free connection. If
this happens, the source cannot be switched back to the
hands-free talk mode by operating this unit. Operate your
cell-phone to return to the hands-free talk mode.
3
Enter a PIN code
Input the PIN code (“0000”) in the Bluetooth
device.
Check that registration is complete on the
Bluetooth device.
✍ PIN code is set to “0000” as the default. You can
change this code. Refer to <Registering PIN
Code> (page 44).
Adjusting the Voice Volume during a Call
Turn the [VOL] knob.
4
By operating the Bluetooth device, start hands-
free connection.
Call Waiting
Step 2. Connection
Answering Another Incoming Call with the
Current Call Suspended
If you have registered 2 or more cell-phones, you
need to select one of them. For more details,
see <Selecting the Bluetooth device You Wish to
Connect> (page 44).
When a cell-phone is connected, the “BT” indicator
is light up.
1
2
Press the [VOL] knob.
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “ANSWER”.
Step 3. Hands-free phoning
You can do hand-free phoning when the
connection is made.
Answering another Incoming Call after
Terminating the Current Call
Press the [SRC] button.
|
20 DPX-U6120/ DPX-U5120/ DPX-MP3120
Download from Www.Somanuals.com. All Manuals Search And Download.
Continuing the Current Call
Speed Dialing (Preset Dial)
1
2
Press the [VOL] knob.
1
Enter Bluetooth mode
Press the [LOG] button for at least 1 second.
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “REJECT”.
2
Select the number you want to recall from the
memory
Press the [1] – [6] button.
Answering the Waiting Call after Terminating
the Current Call
Press the [SRC] button.
3
Make a call
Press the [VOL] knob.
Switching between the Current Call and Waiting
Call
Press the [VOL] knob.
Each pressing of this knob switches the calling
⁄
• You need to register the preset dial number. Refer to
<Registering to the Preset Dial Number List> (page 22).
party.
Calling a Number in the Phone Book
Other Functions
1
Enter Bluetooth mode
Press the [LOG] button for at least 1 second.
Clearing the Disconnection Message
Press the [LOG] buttons for at least 1 second.
“HF Disconnect”/ “HF D-CON” disappears.
2
Select the Phone Book mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Phonebook”.
Making a Call
3
4
Select the initial to be searched for
1
Enter Bluetooth mode
Press the [LOG] button for at least 1 second.
Operation type
Operation
Move to the next character. Turn the [VOL] knob.
Determine the selected initial. Press the [VOL] knob.
2
Select a dialing method
Turn the [VOL] knob and press it when the
desired item is displayed.
Select the name
Operation type
Operation
Display
Overview
Select the Phone number.
Select the name.
Turn the [VOL] knob.
“Phonebook” Selecting the initial to be searched for the phone
book.
“Incoming Calls” Calling a number in the incoming call list.
“Outgoing Calls” Calling a number in the outgoing call list.
“Missed Calls” Calling a number in the missed calls list.
“Number Dial” Making a call by entering phone number.
Press the [
4] or [¢] button.
✍ Switching between Display Modes
Press the [DISP] button.
5
Make a call
Press the [VOL] knob.
Operation method of each mode is described
below.
⁄
• During search, a non-accent character such as “u” is
3
Exit the dialing method mode
Press the [LOG] button for at least 1 second.
searched for instead of an accent character such as “ü”.
English
|
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Function of DPX-U6120 with KCA-BT200/BT300 (Optional Accessory)
Operation of hands-free phoning
Calling a Number in the Call log
Make a Voice Dialing Call
1
Enter Bluetooth mode
Press the [LOG] button for at least 1 second.
1
Enter voice recognition mode
Press the [ATT] button for at least 1 second.
2
Select the call log mode
Turn the [VOL] knob and press it when the
desired item is displayed.
2
“PB Name?” is displayed.
When a beep is heard, say the name within 2
seconds.
Select “Outgoing Calls” (outgoing call),
“Incoming Calls” (incoming call), or “Missed
Calls” (missed call).
3
4
“PN Type?” is displayed.
When a beep is heard, say the category name
within 2 seconds.
3
4
Select a name or phone number
Turn the [VOL] knob.
✍ Switching between Display Modes
Press the [DISP] button.
Make a call
Press the [VOL] knob.
✍ This step is the same as step 4 of the procedure
in <Calling a Number in the Phone Book> (page
21). You can make a call or select a category.
Make a call
Press the [VOL] knob.
⁄
⁄
• If your voice cannot be recognized, a message is displayed.
Pressing the [VOL] knob allows you to retry voice input.
Refer to <Troubleshooting Guide> (page 56).
• Both the name and category require registration of a voice
tag. Refer to <Setting a Voice Command for Category>
(page 46).
• The outgoing call list and the incoming call list, and the
missed call list are the lists of calls originated from and
received at this unit. They are not the ones stored in the
cell-phone memory.
• Audio sound is not output during voice recognition.
Dial a Number
1
Enter Bluetooth mode
Press the [LOG] button for at least 1 second.
Registering to the Preset Dial Number
List
2
Select the number dial mode
Turn the [VOL] knob and press it when the
desired item is displayed.
1
2
Select the phone number you wish to register
Select the phone number with reference to the
following:
- <Calling a Number in the Phone Book> (page 21)
- <Calling a Number in the Call log> (page 22)
- <Dial a Number> (page 22)
Select “Number Dial”.
3
Enter a phone number
Operation type
Operation
Select the numbers.
Move to the next digit.
Delete the last digit.
Turn the [VOL] knob.
Select the number to put in the memory
Press the [1] – [6] button for at least 2 seconds.
Press the [
Press the [
¢
] button.
] button.
4
• Press the number ([1] – [0]), #([FM]), *([AM]), or
+([¢]) button on the remote controller.
✍ To erase the entered phone number digit
by digit:
Press the [4] button on the remote
controller.
4
Make a call
• Press the [VOL] knob.
• Press the [DIRECT] button on the remote
controller.
⁄
• You can input max 32 digits.
|
22 DPX-U6120/ DPX-U5120/ DPX-MP3120
Download from Www.Somanuals.com. All Manuals Search And Download.
Display of Phone Number type
(category)
The category items in the Phone Book are displayed
as follows:
Display
Information
“General”/“
”
General
“Home”/“
“Office”/“
“Mobile”/“
“Other”/“
”
Home
Office
Mobile
Other
”
”
”
English
|
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Display Settings
Display Setting
You can select following Display Setting items.
1
2
3
Select the source
Press the [SRC] button.
DISP
SRC
Enter Function setting mode
Press the [VOL] knob.
4 ¢
VOL
Enter Display Setting mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Settings”/ “SETTINGS” > “Display &
Illumination”/ “DISP & ILLUMI”.
Function of DPX-U6120
Display type select
Press the [DISP] button.
4
Select the Function item
Turn the [VOL] knob and press it when the
desired item is displayed.
DPX-U6120
Mode
Display Type
4-line display mode Displays 3 to 4 lines of text.
3-line display mode Displays 2 to 3 lines of text.
Clock display mode Displays the clock.
Spectrum analyzer Displays a line of text and the spectrum analyzer.
display mode
Display off mode Turns off the display. Turns on temporarily when
you perform an operation.
Display
“Settings”
“Display &
Illumination”
Overview
Making Display and Illumination settings.
⁄
“Display Select” Selecting and customizing the Display type.
“Color Select” Selecting the Illumination Color of the panel.
Refer to <Illumination Color Selection>
• When the 4-line/3-line display mode is selected, the status
(ON/OFF indicator of each function) can be displayed on
the first line, and the icon of the currently selected source
and the text information title can be displayed on the left
side by the following <Information display setting> (page
25) operation.
(page 28).
“DISP & ILLUMI When Display off mode is selected in <Display
OFF”
type select> (page 24), sets whether to turn off
display only or display and key illumination.
“DISP&ILLUMI” / “DISP”
Status display: Select “Settings” > “Display & Illumination >
“Display Select” > “Status”
Side display: Select “Settings” > “Display & Illumination” >
“Display
Dimmer”
Reduces the display Illumination brightness.
“Auto”: Dims the illumination in conjunction
with the Light switch of the vehicle.
“Manual1”: Dims the illumination constantly.
“Manual2”: Dims the illumination darker than
Manual1.
“Display Select” > “Side Select”
“OFF”: Does not dim the illumination.
“Contrast”
“DISP N/P”
Adjusting the display contrast.
“1” - “5” - “12”
Switches the panel display between positive
or negative.
“POSI1”/ “POSI2”/ “NEGA1”/ “NEGA2”
Sets the method of scroll to view hidden text.
“Auto” : Scrolls.
“Text Scroll”
“Once” : Scrolls once.
“OFF” : Does not scroll.
“BT DVC
STATUS”
You can display the connection status, signal
strength, and battery level.
: Battery level of cell-phone.
: Signal strength of cell-phone.
|
24 DPX-U6120/ DPX-U5120/ DPX-MP3120
Download from Www.Somanuals.com. All Manuals Search And Download.
“ILLUMI
Dimmer”
Reduces the key Illumination brightness.
“Auto”: Dims the illumination in conjunction
with the Light switch of the vehicle.
“Manual1”: Dims the illumination constantly.
“Manual2”: Dims the illumination darker than
Manual1.
Text scroll
Press the [DISP] button for at least 1 second.
The displayed text scrolls.
Function of DPX-U6120
“OFF”: Does not dim the illumination.
Information display setting
“ILLUMI Effect” Sets whether the key illumination brightness is
changed in conjunction with the key operation.
“ON”/ “OFF”
“ILLUMI MSC Sets whether the key illumination color is
SYNC”
You can customize the display of the Spectrum
analyzer display mode.
1
2
3
Select the source
Press the [SRC] button.
changed in conjunction with the sound volume.
“ON”/ “OFF”
(
: Factory setting)
Enter Function setting mode
Press the [VOL] knob.
DPX-U5120 DPX-MP3120
Enter the Display Setting mode and select the
Spectrum analyzer display mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Display
“SETTINGS”
“DISP & ILLUMI”
Overview
Making Display and Illumination settings.
“COLOR SELECT” Selecting the Illumination Color of the panel.
Refer to <Illumination Color Selection>
(page 28).
Select “Settings” > “Display & Illumination” >
“Display Select”.
“TEXT SCROLL” Sets the method of scroll to view hidden text.
“AUTO” : Scrolls.
4
Select the setting item to adjust
Turn the [VOL] knob and press it when the
desired item is displayed.
“ONCE” : Scrolls once.
“OFF” : Does not scroll.
“DISP OFF
MODE”
Sets the clock and button illumination when
“DISP OFF MODE”is selected as described in
<Text Display Selection> (page 27).
“ON” : Displays the clock.
“OFF” : Dims the clock.
Display
“Display Select”
Setting
“Side Select” Sets the side part display for 4-line display mode
and 3-line display mode.
“CLOCK”
Text/ Icon/ Disappear
Sets the spectrum analyzer display for Spectrum
analyzer display mode.
“KEY ILLUMI” “ON” : Turns on the button illumination.
“OFF” : Dims the button illumination.
“Graphic
Select”
“DISP DIMMER” Reduces the display Illumination brightness.
“AUTO”: Dims the illumination in conjunction
with the Light switch of the vehicle.
Spectrum analyzer A/ Spectrum analyzer B /
Spectrum analyzer&Text
“Clock Select” Sets the Clock display for Clock display mode.
“MANUAL1”: Dims the illumination constantly.
“MANUAL2”: Dims the illumination darker
than Manual1.
Home/ Home&Sub
“Status”
Sets the status display (ON/OFF indicator for each
function) for 4-line display mode and 3-line display
mode.
“OFF”: Does not dim the illumination.
“ILLUMI
DIMMER”
Reduces the key Illumination brightness.
“AUTO”: Dims the illumination in conjunction
with the Light switch of the vehicle.
“MANUAL1”: Dims the illumination constantly.
“MANUAL2”: Dims the illumination darker
than Manual1.
Appear/ Disappear
5
6
Make a setting
Turn the [VOL] knob.
Exit Function setting mode
Press the [ ] button for at least 1 second.
“OFF”: Does not dim the illumination.
(
: Factory setting)
⁄
5
6
Make a setting
Turn the [VOL] knob to select a setting value,
and then press the [VOL] knob.
• To adjust the “Sub time” with “Home & Sub” selected for
“Clock Select”, select a city in advance using the <Dual clock
city setting> (page 29) function.
Exit Function setting mode
Press the [ ] button for at least 1 second.
English
|
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Display Settings
Function of DPX-U6120
In Music CD source
Selecting text display
Disc title (“Disc Title”)
Track title (“Track Title”)
Play time (“P-Time”)
Spectrum analyzer & Clock
(“Speana/Clock”)
Date (“Date”)
Changes displayed information on each of the
following sources:
Blank (“Blank”)
1
2
3
Select the source
Press the [SRC] button.
In Auxiliary input source
Source name (“Source Name”)
Spectrum analyzer & Clock
(“Speana/Clock”)
Date (“Date”)
Blank (“Blank”)
Enter Function setting mode
Press the [VOL] knob.
Select Text display selection mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Settings” > “Display & Illumination” >
“Display Select” > “Text Select”.
In Standby
Source name (“Source Name”)
Clock (“Clock”)
Date (“Date”)
Blank (“Blank”)
In Bluetooth audio source
4-line display mode
4 Select the text display part
Turn the [VOL] knob.
The selected text display part blinks.
Bluetooth audio (“Source Name”) Spectrum analyzer & Clock
Song title* (“Song Title”)
(“Speana/Clock”)
Date (“Date”)
Blank (“Blank”)
Artist name* (“Artist Name”)
Album name* (“Album Name”)
5 Select the text
Press the [4] or [¢] button
3-line display mode
6
Exit Function setting mode
Press the [ ] button for at least 1 second.
Bluetooth audio (“Source Name”) Spectrum analyzer & Clock
Title & Artist* (“Title/Artist”)
Album & Artist* (“Album/Artist”)
(“Speana/Clock”)
Date (“Date”)
Blank (“Blank”)
In FM Tuner source
Frequency (“Frequency”)
Spectrum analyzer & Clock
(“Speana/Clock”)
Date (“Date”)
Blank (“Blank”)
* Function of KCA-BT300
In Disc changer source (Optional)
In AM Tuner source
Disc title (“Disc Title”)
Track title (“Track Title”)
Play time (“P-Time”)
Spectrum analyzer & Clock
(“Speana/Clock”)
Date (“Date”)
Frequency (“Frequency”)
Spectrum analyzer & Clock
(“Speana/Clock”)
Date (“Date”)
Blank (“Blank”)
Blank (“Blank”)
In USB/ iPod/ Audio file source
4-line display mode
Song title (“Song Title”)
Play time (“P-Time”)
Album name (“Album Name”)
Artist name (“Artist Name”)
Folder name (“Folder Name”)
File name (“File Name”)
Spectrum analyzer & Clock
(“Speana/Clock”)
Date (“Date”)
Blank (“Blank”)
3-line display mode
Title & Artist (“Title/Artist”)
Album & Artist (“Album/Artist”)
Folder name (“Folder Name”)
File name (“File Name”)
Spectrum analyzer & Clock
(“Speana/Clock”)
Date (“Date”)
Blank (“Blank”)
Play time (“P-Time”)
|
26 DPX-U6120/ DPX-U5120/ DPX-MP3120
Download from Www.Somanuals.com. All Manuals Search And Download.
Function of DPX-U5120/ DPX-MP3120
⁄
Text Display Selection
• Setting is available when the 4-line display mode, 3-line
display mode, Clock display mode, or Spectrum analyzer
display (Spectrum analyzer&Text type) mode which allows
text display. Refer to <Display type select> (page 24).
• If the selected display item does not have any information,
alternative information is displayed.
Changing displayed information on each source
following;
Press the [DISP] button.
In Tuner source
• Some items cannot be selected depending on the display
type and row.
• When selecting “Folder Name” while playing with iPod,
names will be displayed depending on currently selected
browsing items.
• If the iPod Control by Hand Mode is set to on while playing
the iPod, “iPod by Hand Mode” is displayed.
• If all characters cannot be displayed while playing with iPod,
the file number in the list is displayed.
Information
Frequency
Display off
Display
“FREQUENCY”
“DISP OFF MODE”
In CD source
Information
Disc title
Track title
Play time & Track number
Display off
Display
“DISC TITLE”
“TRACK TITLE”
“P-TIME”
Information
Music title
Folder name
File name
Display
“DISP OFF MODE”
“TITLE***”
“FLD***”
“FILE***”
In Audio file/ iPod source
Information
Display
Music title & Artist name
Album name & Artist name
Folder name
File name
Play time & Music number
Display off
“TITLE/ARTIST”
“ALBUM/ARTIST”
“FOLDER NAME”
“FILE NAME”
“P-TIME”
“DISP OFF MODE”
In Standby/ Auxiliary input source
Information
Source name
Display off
Display
“SOURCE NAME”
“DISP OFF MODE”
⁄
• When you select the Display off mode, the display setting of
each source will be changed to the Display off.
• If the selected display item does not have any information,
alternative information is displayed.
• When selecting “FOLDER NAME” while playing with iPod,
names will be displayed depending on currently selected
browsing items.
• If all characters cannot be displayed while playing with iPod,
the file number in the list is displayed.
Information
Music title
Folder name
File name
Display
“TITLE***”
“FOLDER***”
“FILE***”
English
|
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Display Settings
Illumination Color Selection
Auxiliary Input Display Setting
Selecting the Illumination Color of the panel.
Selecting the display when changing to Auxiliary
input source.
1
Enter Function setting mode
Press the [VOL] knob.
1
Select the AUX source
Press the [SRC] button.
Select the “AUX” display.
2
Enter Illumination color selection mode
Turn the [VOL] knob and press it when the
desired item is displayed.
2
3
Enter Function setting mode
Press the [VOL] knob.
Select “Settings”/ “SETTINGS” > “Display &
Illumination”/ “DISP & ILLUMI” > “Color Select”/
“COLOR SELECT”.
Enter Auxiliary input display setting mode
Turn the [VOL] knob and press it when the
desired item is displayed.
3
4
Select the place where you want to set the
Illumination Color
Turn the [VOL] knob and press it when the
Select “Settings”/ “SETTINGS” > “AUX Name
Set”/ “AUX NAME SET”.
desired item is displayed.
4
5
Select the Auxiliary input display
Turn the [VOL] knob.
Select “AUX”, “DVD”, “PORTABLE”, “GAME”, “VIDEO”, or
Place
Display
Display and key
“All”/“ALL”
Display
Key
“Display”/“DISPLAY”
“Key”/“KEY”
“Knob”
“TV”
Exit Function setting mode
Press the [ ] button for at least 1 second.
Volume knob (DPX-U6120 only)
Select the Illumination Color
Turn the [VOL] knob and press it when the
⁄
• The Auxiliary input display can be set only when the built-in
auxiliary input or the auxiliary input of optional KCA-S220A
is used. On the KCA-S220A, “AUX EXT” is displayed by
default.
desired item is displayed.
Select the color from “Variable Scan”/ “VARIABLE
SCAN”, “Color1”/ ”COLOR1” — “Color24”/ ”COLOR24”,
or “User”/ “USER”.
Creating “User”/”USER” color
You can create your original color during the
selection from “Color1”/ ”COLOR1” — “Color24”/
”COLOR24”.
The color you created can be called when you
select “User”/ “USER”.
1. Press the [VOL] knob for at least 1 second.
Enter the detail color adjustment mode.
2. Set the color.
Operation type
Operation
To select the color to adjust. Press the [4] or [¢] button.
(red, green, or blue)
To adjust color.
(Range: 0 – 9)
Turn the [VOL] knob.
3. Press the [VOL] knob.
Exit the detail color adjustment mode.
5
Exit Function setting mode
Press the [ ] button for at least 1 second.
|
28 DPX-U6120/ DPX-U5120/ DPX-MP3120
Download from Www.Somanuals.com. All Manuals Search And Download.
Clock and Other Functions
5
Adjusting Date
1. Turn the [VOL] knob to adjust the year.
2. Press the [VOL] knob.
3. Turn the [VOL] knob to adjust the month.
4. Press the [VOL] knob.
5. Turn the [VOL] knob to adjust the day.
6. Press the [VOL] knob.
SRC
6
7
8
Enter Date format mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Date Mode”.
DPX-U5120
DPX-MP3120
B.BOOST
4 ¢
VOL
Function of DPX-U6120
Select Date format
Clock and Date Adjustment
Turn the [VOL] knob and press it when the
desired item is displayed.
Select from 7 types.
You can adjust the clock and date.
Display
Overview
Exit Function setting mode
Press the [ ] button for at least 1 second.
“Settings”
“Clock & Date”
“Clock Adjust”
“City Select”
Sets the clock.
Sets the two cities to be displayed when
“Home&Sub type”is selected for“Clock
Select”. Refer to <Information display
setting> (page 25), <Dual clock city
setting> (page 29).
Function of DPX-U6120
Dual clock city setting
You can select cities for two clocks.
“Sub Clock Adjust” Adjusts the time difference caused by
1
2
Enter Function setting mode
Press the [VOL] knob.
summer time.
“-1h” / “0h” / “+1h”
Advances the clock one hour when set
to ON.
“ON” / “OFF”
Sets the date.
Sets the date display mode.
“Summer Time”
Select City Select mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Settings” > “Clock & Date” > City Select”
“Date Adjust”
“Date Mode”
(
: Factory setting)
3 Select the city (Home or Sub) display part
Turn the [VOL] knob.
1
2
Enter Function setting mode
Press the [VOL] knob.
The selected city display part blinks.
4 Set cities for Home/ Sub
Enter Clock adjustment mode
Turn the [VOL] knob and press it when the
Press the [4] or [¢] button
desired item is displayed.
Select “Settings” > “Clock & Date” > “Clock
Adjust”.
5
Exit Function setting mode
Press the [ ] button for at least 1 second.
⁄
3
4
Adjusting Clock
1. Turn the [VOL] knob to set the hours.
2. Press the [¢] button.
3. Turn the [VOL] knob to set the minutes.
4. Press the [VOL] knob.
• To display the clocks of two cities, select “Home&Sub” type
for “Clock Select” described in <Information display setting>
(page 25).
• For adjustment of Home time, refer to <Clock and Date
Adjustment> (page 29).
• Time of Sub City is automatically derived from Home time.
When summer time systems are different between Home
and Sub cities, adjustment can be done by referring to “Sub
Clock Adjust” of <Clock and Date Adjustment> (page 29).
Enter Date adjustment mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Date Adjust”.
English
|
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Clock and Other Functions
Function of DPX-U5120/ DPX-MP3120
“Beep”/“KEY
BEEP”
Setting the operation check sound (beep sound)
ON/OFF.
“ON”/ “OFF”
When this is set to ON, the following character
strings are displayed in Chinese:
Folder name/ File name/ Song title/ Artist
name/ Album name/ KCA-BT300/BT200
(optional accessory)
Clock Adjustment
You can adjust the clock and date.
“Chinese”*
1
2
3
Enter Clock adjustment mode
Press the [B.BOOST] button for at least 1
second.
“ON”/ “OFF”
The hour display blinks.
“Built in AUX”/ When this is set to ON, AUX source can be
“BUILT-IN AUX” selected.
Adjust the hour
Turn the [VOL] knob to adjust the hour, and
then press the [VOL] knob.
The minute display blinks.
“ON”: Allows AUX source to be selected. Use
this setting when the built-in AUX terminal
is connected to the external equipment all
the time.
“OFF”: Disable AUX source selection. Use this
setting when the built-in AUX terminal is
not used.
Adjust the minute
Turn the [VOL] knob to adjust the minute, and
then press the [VOL] knob.
Finish the Clock Adjustment.
“Forced CD-DA”/ Sets the CD read mode.
“CD READ”
“Settings 1”/”1”: Automatically distinguishes
between Audio file disc and music CD when
playing disc.
Initial Settings
“Settings 2”/”2”: Forces playing as music CD.
You can select the following Initial Setting items.
“Built in AMP”* Selecting“OFF”turns off the built-in amplifier.
Turning off the built-in amplifier improves the
quality of the sound from Preout.
1
Select the Standby
Press the [SRC] button.
“ON”/ “OFF”
Switches the preout between rear output and
Select the “STDBY”/ “STANDBY” display.
“Switchable
Preout”/“SWITCH subwoofer output.
PREOUT” “Rear”/ “REAR”: Rear output
“SubWoofer”/ “SUB-W”: Subwoofer output
“SP SELECT”** Fine-tuning so that the System Q value is
optimal when setting the speaker type as
follows;
2
3
Enter Function setting mode
Press the [VOL] knob.
Enter Initial Setting mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Initial Settings”/ “INITIAL SET”.
“SP OFF”: Off
“SP 5/4”: For 5 & 4 in. speaker
“SP 6*9/6”: For 6 & 6x9 in. speaker
“SP OEM”: For the OEM speaker
4
Select the setting item to adjust
Turn the [VOL] knob.
“System F/W
Upgrades the firmware.
Display
“Initial Settings”/
“INITIAL SET”
“Source Select”* Sets the source selection method.
Select“2”to change the source selection
method. Press the [SRC] button, turn the [VOL]
knob to select the source, and then press the
[VOL] knob to determine it.
Overview
Update”/“F/W Selecting“YES”and then pressing [VOL] knob
UP”
starts upgrading the firmware.
For how to update the firmware, access our web
(
: Factory setting)
* Function of DPX-U6120
** Function of DPX-U5120/DPX-MP3120
“Settings 1”/ “2”
“Tuner Preset
Sets the Tuner preset type.
5
6
Make a setting
Turn the [VOL] knob to select a setting value,
and then press the [VOL] knob.
Type”/“PRESET “Type Normal”/ “TYPE NORMAL”: 1 station
TYPE”
can be assigned to 1 preset button in each
of 4 bands (FM1, FM2, FM3, and AM), i.e.,
a total of 24 stations (6 stations x 4 bands)
can be preset.
“Type Mixed”/ “TYPE MIXED”: A total of 6
stations can be assigned to a total of 6 preset
buttons regardless of band (FM1, FM2, FM3,
and AM). You can recall a preset station
without switching between bands.
Exit Function setting mode
Press the [ ] button for at least 1 second.
|
30 DPX-U6120/ DPX-U5120/ DPX-MP3120
Download from Www.Somanuals.com. All Manuals Search And Download.
Demonstration mode Setting
Muting volume upon reception of
Phone call
Turning the demonstration mode ON/OFF.
The audio system automatically mutes upon
reception of an incoming call.
1
Enter Function setting mode
Press the [VOL] knob.
2
Enter Demonstration mode setting
Turn the [VOL] knob and press it when the
desired item is displayed.
When a call comes in
“CALL” is displayed.
The audio system pauses.
Select “DEMO Mode”/ “DEMO MODE”.
Listening to the audio during a call
Press the [SRC] button.
The “CALL” display disappears and the audio system
3
4
Set the Demonstration mode
Turn the [VOL] knob and press it when the
desired item is displayed.
comes back ON.
Select “ON” or “OFF”.
When the call ends
Hang up the phone.
The “CALL” display disappears and the audio system
Exit Function setting mode
Press the [ ] button for at least 1 second.
comes back ON.
⁄
• To use the TEL Mute feature, you need to hook up the MUTE
wire to your telephone using a commercial telephone
accessory. Refer to <Connecting Wires to Terminals> (page
53).
English
|
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Function of DPX-U6120
Audio Adjustments – DPX-U6120 –
“Volume offset” Sets each source’s volume as a difference from
the basic volume.
“–8” — “ 0” (AUX: “-8”— “+8”)
“2Zone”
“2Zone Select”
“Preset”
Sets the Dual Zone System.
- <Dual Zone System> (page 35).
Sets the audio preset.
- <Audio Preset Memory> (page 39).
- <Audio Preset Recall> (page 39).
SRC
(
: Factory setting)
4 ¢
VOL
1
Select the source
Press the [SRC] button.
Select a source other than “STDBY”.
Audio Control
2
3
Enter Function setting mode
Press the [VOL] knob.
You can adjust the following Audio Setting items.
Display
“Audio Control”
“SubWoofer Level” You can set subwoofer level.
Overview
Enter Audio Control mode
Turn the [VOL] knob and press it when the
desired item is displayed.
“–15” — “0” — “+15”
Select “Audio Control”.
“DSP Set”
“Bypass”: Disables the DSP function.
“Through”: Enables the DSP function.
Sets the sound quality.
- <Preset Equalizer curve Select> (page 33).
- <Manual Equalizer Control> (page 33).
Sets the Bass Boost level in two steps.
“OFF”/ “Step1” – “2”
4
5
6
Select the setting item to adjust
Turn the [VOL] knob and press it when the
desired item is displayed.
“Equalizer”
“Bass Boost”
Make a setting
Turn the [VOL] knob to select a setting value,
and then press the [VOL] knob.
“HIGHWAY-SOUND” Compensates the low volume or bass sound
being lost by road noises to make vocal sound
clearer.
Exit Function setting mode
Press the [ ] button for at least 1 second.
Unavailable when the tuner source is selected.
“OFF”/ “Step1”/ “2”/ “3”
Turns ON/OFF the Supreme plus function.
Can be set while Music CD source, Audio file
source of USB and iPod source.
Remarks
• DSP Set
“Supreme+”
“Position”
When “DSP Set” is set to “Bypass”, the DSP function is
disabled , and the colored items can not be set.
“ON”/ “OFF”
Compensates the sound environment in
accordance with the listening position.
- <Listening Position Selection> (page 34).
- <Listening Position Fine Adjustments>
(page 34).
• HIGHWAY-SOUND
Increases the volume of faintest sound being lost by road
noises to make the sound more audible. Additionally, it
accentuates bass sound being lost by road noises to make
the bass sound more dynamic.
“Balance”
“Fader”
Adjusts left/right speaker balance.
(Left) “L15” — “0” — “R15” (Right)
Adjusts front/rear speaker balance.
(Rear) “R1”5 — “0” — “F15” (Front)
• Supreme+ (Supreme Plus)
Technology to extrapolate and supplement with
proprietary algorithm, the high-frequency range that is cut
off when encoding. The bass and vocal sound that are cut
off by encoding are supplemented for the reproduction
of natural sound quality. Supplementing is optimized by
compression format (AAC, MP3 or WMA) and processed
according to bit rate. The effect is negligible with music
that is encoded at high bit rate, variable bit rate or has
minimal high frequency range.
“2Zone Rear Volume” Refer to <Dual Zone System> (page 35).
“SubWoofer”
Turns on/off the subwoofer output.
“ON”/ “OFF”
“Detailed Setup”
“Car Type”
“Speaker Setting”
“Car Type Adjust”
“X'Over”
To get clear sound, set the sound environment
according to the location and size of physically
installed speakers with reference to the
followings:
- <Car Type Selection> (page 37).
- <Speaker Setting> (page 37).
- <Car Type Fine Adjustments> (page 38).
- <X’Over Setting> (page 38).
The bass and vocal sound of Music CD/ iPod is also
supplemented.
• Dual Zone System
Main source and sub source (Auxiliary input) output Front
channel and Rear channel separately.
|
32 DPX-U6120/ DPX-U5120/ DPX-MP3120
Download from Www.Somanuals.com. All Manuals Search And Download.
Preset Equalizer curve Select
Manual Equalizer Control
You can select the following Equalizer curve.
You can adjust the following Equalizer Control
items.
Display
“Natural”
“User”
Equalizer curve
Natural
User*
Band
Item
Range
“BAND1”(62.5 Hz) “GAIN”Band level
“EFCT”Bass Effect
“BAND2”(250 Hz) “GAIN”Band level
-9 –+9 dB
“ON”/“OFF”
-9 –+9 dB
-9 –+9 dB
-9 –+9 dB
-9 –+9 dB
: Factory setting)
“Rock”
“Pops”
“Easy”
Rock
Pops
Easy
“BAND3”(1 kHz)
“BAND4”(4 kHz)
“GAIN”Band level
“GAIN”Band level
“Top 40”
“Jazz”
Top 40
Jazz
“BAND5”(16 kHz) “GAIN”Band level
“Game”
“iPod”
Game
(
iPod (During iPod source only)
1
Select the source
Press the [SRC] button.
* The Equalizer curve set in the section <Manual Equalizer
Control> is recalled.
Select a source other than “STDBY”.
(
: Factory setting)
2
3
Enter Function setting mode
Press the [VOL] knob.
1
Select the source
Press the [SRC] button.
Select a source other than “STDBY”.
Enter Manual Equalizer Control mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Audio Control” > “Equalizer” > “Manual
Equalizer”.
2
3
Enter Function setting mode
Press the [VOL] knob.
Enter Preset Equalizer mode
Turn the [VOL] knob and press it when the
desired item is displayed.
4
Select the item you want to set
Select “Audio Control” > “Equalizer” >
“Preset Equalizer”.
Operation type
Selects the item.
Adjust each item.
Set the value.
Operation
Turn the [VOL] knob.
Press the [
Press the [VOL] knob.
4] or [¢] button.
4
Select the Equalizer curve
Turn the [VOL] knob.
✍ Select the iPod Equalizer curve
You can select from 22 Equalizer curve types for
iPod when “iPod” is selected.
1. Enter iPod Equalizer mode
Press the [VOL] knob.
2. Select the iPod Equalizer curve
Turn the [VOL] knob and press it when the
desired item is displayed.
5
Exit Function setting mode
Press the [ ] button for at least 1 second.
⁄
• When “iPod” is selected in the section <Preset Equalizer
curve Select> (page 33), Manual Equalizer Control is disabled.
• You can select for each source.
5
Exit Function setting mode
Press the [ ] button for at least 1 second.
⁄
• You can select for each source.
English
|
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Function of DPX-U6120
Audio Adjustments – DPX-U6120 –
Listening Position Selection
Listening Position Fine Adjustments
The sound environment can be compensated in
accordance with the selected position. According to
the listening position, select the position from the
Making fine adjustment of the value specified at
Preset position selection per speaker.
1
Select the source
Press the [SRC] button.
following settings.
Select a source other than “STDBY”.
Compensation seat
Not compensating.
Front-Left seat
Front-Right seat
Front seat
Display
“All”
“Front-Left”
“Front-Right”
“Front”
2
3
Enter Function setting mode
Press the [VOL] knob.
Enter Manual position setting mode
Turn the [VOL] knob and press it when the
desired item is displayed.
(
: Factory setting)
1
Select the source
Press the [SRC] button.
Select a source other than “STDBY”.
Select “Audio Control” > “Position” > “DTA”.
4
Select the speaker you want to set
Turn the [VOL] knob and press it when the
desired value is displayed.
2
3
Enter Function setting mode
Press the [VOL] knob.
Item
“Front”
“L”
“R”
“Rear”
“L”
“R”
“Subwoofer”
“L”
“R”
“Initialize”
Setting overview
Enter Preset position setting mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Audio Control” > “Position” > “Preset
Position”.
Front Left speaker
Front Right speaker
Rear Left speaker
Rear Right speaker
4
5
Select the seat you want to compensate
Turn the [VOL] knob.
Subwoofer Left
Subwoofer Right
Initialize the setting values.
Exit Function setting mode
Press the [ ] button for at least 1 second.
5
6
Set the value
Press the [4] or [¢] button
Adjust between 0 and 170 cm.
Exit Function setting mode
Press the [ ] button for at least 1 second.
|
34 DPX-U6120/ DPX-U5120/ DPX-MP3120
Download from Www.Somanuals.com. All Manuals Search And Download.
Dual Zone System
Main source and sub source (Auxiliary input) output
Front channel and Rear channel separately.
Display
Overview
“2Zone Rear Volume”* Adjust the volume of Rear channel.
“0” — “35”
“Detailed Setup”
“2Zone”
Sets the Dual Zone System.
“ON”/ “OFF”
“2Zone Select”*
Specifies the destination of sub source sound
when the Dual Zone function is turned on.
“Rear”/ “Front”
* The Dual Zone System is set to “ON”.
(
: Factory setting)
1
Select the source
Press the [SRC] button.
Select a source other than “STDBY”.
2
3
Enter Function setting mode
Press the [VOL] knob.
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Audio Control” > “Detailed Setup”.
4
5
Select the item you want to set
Turn the [VOL] knob and press it when the
desired item is displayed.
Exit Function setting mode
Press the [ ] button for at least 1 second.
⁄
• Select Main source by [SRC] button.
• Adjust the volume of Front channel by [VOL] knob.
• The Audio Control has no effect on sub source.
• There are following limitations when Dual Zone System is
enabled.
- There is no output from the subwoofer.
- “Fader”,“SubWoofer Level”of <Audio Control> (page 32) and
DSP function are not available.
• The Bluetooth audio source can be set exclusively to the
front speaker. Set “2Zone Select” to “Rear”.
English
|
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Function of DPX-U5120/ DPX-MP3120
Audio Adjustments – DPX-U5120/ DPX-MP3120 –
“DETAILED SET”
“LPF
SUBWOOFER”
Selects cut off frequency of subwoofer output.
“85”/ “120”/ “160”/ “THROUGH” (OFF) Hz
“SUB-W PHASE” Selects the phase of subwoofer output.
“REVERSE” (180°)/ “NORMAL” (0°)
“SUPREME SET” Turns on/off the supreme function.
Can be set while Audio file source of CD/USB
(excluding iPod).
SRC
“ON”/ “OFF”
Sets each source’s volume as a difference from
the basic volume.
VOL
“VOLUME
OFFSET”
“–8” — “0” (AUX: “–8” — “0” — “+8”)
Audio Control
(
: Factory setting)
You can adjust the following Audio Setting items.
1
Select the source
Press the [SRC] button.
Display
Overview
Select a source other than “STANDBY”.
“AUDIO CONTROL”
“SUBWOOFER SET” Turns on/off the subwoofer output.
2
3
Enter Function setting mode
Press the [VOL] knob.
“OFF”/ ”ON”
“SYSTEM Q”
Switches between the following preset
equalizer curves.
Enter Audio Control mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “AUDIO CONTROL”.
“NATURAL”/ “USER”/ “ROCK”/ “POPS”/
“EASY”/ “TOP40”/ “JAZZ”/ “GAME”
For USER: This appears when Bass level,
Middle level, and Treble level are
adjusted.
4
5
6
Select the setting item to adjust
Turn the [VOL] knob and press it when the
desired item is displayed.
“BASS ADJUST”
“BASS FREQ”
You can set bass for each source.
Bass Center Frequency
40/50/60/70/80/100/120/150 (Hz)
Bass level
“–8” — “0” — “+8”
Bass Q Factor
Make a setting
Turn the [VOL] knob to select a setting value,
and then press the [VOL] knob.
“BASS LEVEL”
“BASS Q”
1.00/1.25/1.50/2.00
Bass Extend
Exit Function setting mode
Press the [ ] button for at least 1 second.
“BASS EXT”
”ON”/ “OFF”
“MID ADJUST”
“MID FREQ”
You can set middle for each source.
⁄
Middle Center Frequency
0.50/1.00/1.50/2.00 (kHz)
Middle level
“–8” — “0” — “+8”
Middle Q Factor
1.00/2.00
You can set treble for each source.
Treble Center Frequency
10.0/12.5/15.0/17.5 (kHz)
Treble level
• The “SUB-W PHASE” item can be made when a setting other
than “THROUGH” is selected for the “LPF SUBWOOFER” item.
“MID LEVEL”
“MID Q”
Remarks
• Supreme
Technology to extrapolate and supplement with
proprietary algorithm, the high-frequency range that is
cut off when encoding at low bit rate (less than 128Kbps,
Sampling frequency is 44.1kHz).
Supplementing is optimized by compression format (MP3,
WMA and AAC) and processed according to bit rate. The
effect is negligible with music that is encoded at high bit
rate, variable bit rate or has minimal high frequency range.
“TRE ADJUST”
“TRE FREQ”
“TRE LEVEL”
“BALANCE”
“–8” — “0” — “+8”
Adjusts left/right speaker balance.
(Left)“L15” — “0” — “R15” (Right)
Adjusts front/rear speaker balance.
(Rear)“R15” — “0” — “F15” (Front)
You can set subwoofer level.
“–15” — “0” — “+15”
“FADER”
“SUB-W LEVEL”
|
36 DPX-U6120/ DPX-U5120/ DPX-MP3120
Download from Www.Somanuals.com. All Manuals Search And Download.
Function of DPX-U6120
DSP Setup
Speaker Setting
The speaker X’Over is automatically set when the
position and size of each speaker are selected from
the following items.
Speaker
Item
Range
“Front”
“SIZE”
Speaker Size Front
SRC
“O.E.M.”, “10cm”, “13cm”, “16cm”,
“17cm”, “18cm”, “4x6”, “5x7”, “6x8”,
“6x9”, “7x10”
4 ¢
VOL
“LOCATION” Speaker Location Front
“Door”, “On Dash”, “Under Dash”
“TWEETER” Speaker Size Tweeter
“None”, “Use”
Speaker Size Rear
“None”, “O.E.M.”, “10cm”, “13cm”,
“16cm”, “17cm”, “18cm”, “4x6”, “5x7”,
“6x8”, “6x9”, “7x10”
Car Type Selection
“Rear”
“SIZE”
You can compensate the delay of the sound arrival
time by selecting your environment from the
following car types.
“LOCATION” Speaker Location Rear
Display
Overview
• “Door”, “Rear Deck”
“OFF”
Not compensating.
Compact car
Full size car
Station wagon
Minivan
Sport-utility vehicle
Long Minivan
• “2nd Row”, “3rd Row” (Car Type:
“Minivan”, “Minivan (Long)”)
“Compact”
“Full size car”
“Wagon”
“Minivan”
“SUV”
“SubWoofer” “SIZE”
Speaker Size Subwoofer
“None”, “16cm”, “20cm”, “25cm”,
“30cm”, “38cm Over”
(
: Factory setting)
“Minivan (Long)”
1
Select the source
(
: Factory setting)
Press the [SRC] button.
Select a source other than “STDBY”.
1
Select the source
Press the [SRC] button.
Select a source other than “STDBY”.
2
3
Enter Function setting mode
Press the [VOL] knob.
2
3
Enter Function setting mode
Press the [VOL] knob.
Enter Speaker setting mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Audio Control” > “Detailed Setup” >
“Speaker Setting”.
Enter Cabin select mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Audio Control” > “Detailed Setup” >
“Car Type”.
4
5
Select the item you want to set
Operation type
Selects the item.
Adjust each item.
Set the value
Operation
Turn the [VOL] knob.
4
5
Select the car type
Turn the [VOL] knob to select the car type, and
then press the [VOL] knob.
Press the [
Press the [VOL] knob.
4] or [¢] button.
Exit Function setting mode
Press the [ ] button for at least 1 second.
Exit Function setting mode
Press the [ ] button for at least 1 second.
⁄
• You can compensate the distances in more details by using
<Car Type Fine Adjustments> (page 38) function.
English
|
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Function of DPX-U6120
DSP Setup
Reference point
Car Type Fine Adjustments
Adjusting fine tuning of the speaker position
compensation value specified at <Car Type
Selection> (page 37).
+100cm
FRONT
FRONT
REAR
Display
“FRONT”
“REAR”
“SW”
Item
Range
50cm
Front speaker
Rear speaker
Subwoofer
0 – 440 cm
0 – 440 cm
0 – 440 cm
80cm
REAR
+70cm
(
: Factory setting)
150cm
1
Select the source
Press the [SRC] button.
Select a source other than “STDBY”.
+0cm
SUB-W
2
3
Enter Function setting mode
Press the [VOL] knob.
5
Exit Function setting mode
Press the [ ] button for at least 1 second.
Enter Car Type Adjustment mode
Turn the [VOL] knob and press it when the
desired item is displayed.
X’Over Setting
Select “Audio Control” > “Detailed Setup” >
“Car Type Adjust”.
Fine adjusting the following setting values
corresponding to the X’Over values set in the
section <Speaker Setting> (page 37).
4
Select the item you want to set
Operation type
Selects the item.
Adjust each item.
Set the value
Operation
Turn the [VOL] knob.
Display
Item
Range
Press the [
Press the [VOL] knob.
4] or [¢] button.
“X’Over”
“Front”
“FC”
Front High Pass Filter
Through, 30, 40, 50, 60, 70, 80, 90,
The settings of the delay time are automatically
identified and compensated by specifying the
distances of each speaker from the center of the
vehicle interior.
1 Set the front and rear positions and the height
of the reference point to the position of the ears
of the person sitting in the front seat, and set
the right and left positions to the center of the
vehicle interior.
2 Measure the distances from the reference point
to the speakers.
3 Calculate the distance difference in accordance
with the farthest speaker.
100, 120, 150, 180, 220, 250 (Hz)
“SLOPE” Front High Pass Slope
-6, -12, -18, -24 dB/Oct
Rear High Pass Filter
Through, 30, 40, 50, 60, 70, 80, 90,
100, 120, 150, 180, 220, 250 (Hz)
“Rear”
“FC”
“SLOPE” Rear High Pass Slope
-6, -12, -18, -24 dB/Oct
Subwoofer Low Pass Filter
30, 40, 50, 60, 70, 80, 90, 100, 120,
150, 180, 220, 250, Through (Hz)
“SubWoofer” “FC”
“SLOPE” Subwoofer Slope
-6, -12, -18, -24 dB/Oct
“PHASE” Subwoofer Phase
Reverse (180°)/ Normal (0°)
(
: Factory setting)
1
Select the source
Press the [SRC] button.
Select a source other than “STDBY”.
2
3
Enter Function setting mode
Press the [VOL] knob.
Enter X’Over setting mode
Turn the [VOL] knob and press it when the
desired item is displayed.
|
38 DPX-U6120/ DPX-U5120/ DPX-MP3120
Download from Www.Somanuals.com. All Manuals Search And Download.
When you press the Reset, all the sources will be the setting
value which is registered.
• Preset number “1” and “2”:
Select “Audio Control” > “Detailed Setup” >
“X’Over”.
4
5
Select the speaker you want to set
Turn the [VOL] knob and press it when the
desired item is displayed.
The memory cannot be erased by the Reset button.
• This function cannot be registered when the iPod Equalizer
set in <Preset Equalizer curve Select> (page 33).
Select “Front”, “Rear”, or “SubWoofer”.
Audio Preset Recall
Select the item you want to set
Recalling the sound setup registered by <Audio
Preset Memory> (page 39).
Operation type
Selects the item.
Adjust each item.
Set the value
Operation
Turn the [VOL] knob.
Press the [
Press the [VOL] knob.
4] or [¢] button.
1
Select the source
Press the [SRC] button.
Select a source other than “STDBY”.
6
7
Repeat steps 4 to 5 to complete the X’Over
settings.
2
3
Enter Function setting mode
Press the [VOL] knob.
Exit Function setting mode
Press the [ ] button for at least 1 second.
Enter Audio preset recall mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Audio Control” > “Detailed Setup” >
“Preset” > “Preset Recall”.
Audio Preset Memory
Registering the value setup by Sound Control.
1
Setup Sound Control
Refer to the following operations to setup the
Sound Control.
- <Car Type Selection> (page 37)
- <Speaker Setting> (page 37)
- <Car Type Fine Adjustments> (page 38)
- <X’Over Setting> (page 38)
- <Manual Equalizer Control> (page 33)
- <Listening Position Selection> (page 34)
- <Listening Position Fine Adjustments> (page 34)
4
5
Select the number to recall in the memory
Turn the [VOL] knob and press it when the
desired item is displayed.
Select preset number.
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “YES”.
“Recall Completed” is displayed.
6
Exit Function setting mode
Press the [ ] button for at least 1 second.
2
Enter Audio preset memory mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Audio Control” > “Detailed Setup” >
“Preset” > “Preset Memory”.
⁄
• The “User” of <Preset Equalizer curve Select> (page 33) is
changed to the value which was recalled.
• The Equalizer curve is changed to the value which was
recalled by the selected source.
3
4
Select the number to put in the memory
Turn the [VOL] knob and press it when the
desired item is displayed.
Select a preset number.
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “YES”.
“Memory Completed” is displayed.
5
Exit Function setting mode
Press the [ ] button for at least 1 second.
⁄
• Register 6 patterns of Audio Preset Memory.
• Preset number “1”:
English
|
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Function of DPX-U6120
Log Function
Log Function item lock
Locks the Log Function items to prevent them from
being deleted automatically.
1 Display the Log Function list
Press the [LOG] button.
2 Lock the Log Function item
VOL
LOG
Turn the [VOL] knob to select item, and then
press the [VOL] knob for at least 1 second.
Locked items are indicated with “ ”.
Performing this step again will unlock the locked
item.
Log Function recall
This unit automatically memorizes the previously
used functions and Function setting items, which
can easily be recalled.
3 Exit Log Function
Press the [
] button.
1 Display the Log Function list
Press the [LOG] button.
Deleting a Log Function item
2 Recall the desired function
Deletes Log Function items.
Turn the [VOL] knob to select Log Function
item, and then press the [VOL] knob.
1
Enter Function setting mode
Press the [VOL] knob.
Category display
“FM”
“AM”
“iPod”
“USB”
Function category
FM broadcast
AM broadcast
iPod music
2 Select the Log delete mode
Turn the [VOL] knob and press it when the
desired item is displayed.
USB music
CD music
Select “Settings” > “Log” > “Log Delete”
“CD”
3 Select the Log Function item to delete
Turn the [VOL] knob to select Log Function
item, and then press the [VOL] knob.
Selecting “All” deletes all Log Function. (exclude a
locked items.)
“INIT”
“SET”
“DISP”
“AUD”
“BT”
Initial setting item
Setting item
Display setting item
Audio control setting
Calling number
4 Turn the [VOL] to select “YES”, and then press
the [VOL] knob.
“Completed” is displayed.
Cancelling the Log Function recall
Press the [ ] button.
⁄
5
Exit Function setting mode
Press the [ ] button for at least 1 second.
•
•
•
•
•
Maximum of 15 recently used functions are logged. When this
limit is reached, they are deleted from the oldest.
Logged functions can be deleted. Refer to <Deleting a Log
Function item> (page 40).
Functions to be logged can be set by categories. Refer to
<Log Function category setting> (page 41).
Logged functions can be locked to avoid them being deleted.
Refer to <Log Function item lock> (page 40).
Stations are logged after 1 minutes of reception.
This timing can be changed. Refer to <Tuner Log Function
time setting> (page 41).
|
40 DPX-U6120/ DPX-U5120/ DPX-MP3120
Download from Www.Somanuals.com. All Manuals Search And Download.
Log Function category setting
Tuner Log Function time setting
Sets the function category to be logged.
You can set the timing to log the station by the
reception time.
1
Enter Function setting mode
Press the [VOL] knob.
1
Enter Function setting mode
Press the [VOL] knob.
2 Select the Log Function setting mode
Turn the [VOL] knob and press it when the
desired item is displayed.
2 Select the Tuner Log time set mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Settings” >“Log” >“Log settings”
Select “Settings” >“Log” >“Tuner Log Time Set”
3 Set the category to be logged
3 Set the reception time for the timing to start
logging the station
Turn the [VOL] knob to select time (“10SEC”,
“30SEC”, “1MIN”, “2MIN”, or “5MIN”), and then
press the [VOL] knob.
Category display
“Tuner Log”
Setting category
Radio-related
“Data CD Log”
“iPod Log”
CD-related
iPod-related
“USB Log”
USB-related
“Phone Log”
“Function Log”
Call-related (KCA-BT200/BT300 only)
Function setting-related
4
Exit Function setting mode
Press the [ ] button for at least 1 second.
Turn the [VOL] knob to select category, and
then press the [VOL] knob.
Check-mark (“✔”) the category you want to register.
4
Exit Function setting mode
Press the [ ] button for at least 1 second.
English
|
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Function of DPX-U6120 with KCA-BT200/BT300 (Optional Accessory)
Bluetooth Setup
“Bluetooth HF/ You can specify output speakers for hands-free
Audio”
voice communication and Bluetooth audio
sound.
“Front”: Outputs voice from the front speakers.
“All”: Outputs voice from the front and rear
speakers.
“Call Beep”
You can output a beep from the speaker when
a call comes in.
“ON”: Beep is heard.
“OFF”: Beep is canceled.
4 ¢
LOG VOL
“BT F/W Update” Display the version of the firmware of this unit.
“Mic Gain”*
Adjust the sensitivity of the microphone for a
telephone call. Adjust the voice of caller. Setting
to“+”increases the voice volume.
“–3” – “0” – “+3”
Bluetooth Setting
You can select the following Bluetooth Setting
items.
“NR Level”*
Reduce the noises generated by surrounding
environment without changing the microphone
volume. Adjust the voice of caller when it is
not clear. Setting to“+”increases the noise
reduction.
1 Press the [LOG] button for at least 1 second.
2
Turn the [VOL] knob and press it when the
desired item is displayed.
“–3” – “0” – “+3”
Select “Settings”.
“Echo Cancel
Level“*
Adjust the level of echo cancellation. Setting to
“+”increases the echo cancel reduction.
“–2” – “0” – “+2”
3
Select the Setting item
Turn the [VOL] knob and press it when the
(
: Factory setting)
desired item is displayed.
* Function of KCA-BT300
Display
“Settings”
“PAIRING”
“Device
Overview
4
5
Make a setting
Turn the [VOL] knob to select a setting value,
and then press the [VOL] knob.
Register a Bluetooth device (pairing).
Refer to <Registering Bluetooth device>
(page 43).
Select a cell-phone or Bluetooth audio player
connection.
Registration”
Exit BT Settings mode
Press the [LOG] button for at least 1 second.
“Phone
Selection”
Remarks
• “Auto Answer” (Setting the Time Interval for Automatic
Answer)
Refer to <Selecting the Bluetooth device You
Wish to Connect> (page 44).
“Audio Selection”
This function automatically answers (responds to) a call
after lapse of the preset time interval for automatic answer.
“OFF” : Does not answer the phone call automatically.
“0” : Automatically answers the phone call at once.
“1s” – “99s” : Automatically answers the phone call after
lapse of 1 – 99 seconds.
“Special Device Register a Bluetooth device (pairing).
Select”
Refer to <Registering Bluetooth device>
(page 43).
“Device Delete” Cancel registration of the Bluetooth device.
Refer to <Deleting a Registered Bluetooth
device> (page 45).
“SMS Download” Download a short message.
Refer to <Downloading the SMS> (page 47).
⁄
• If the time set in the cell-phone is shorter than that set in
the unit, the former will be used.
“Voice Tag”
Registers voice for voice recognition and voice
to select the Phone number category in Phone
book.
• This function does not work for call waiting.
• “Bluetooth HF/Audio” (Setting up the Voice Output
Speakers)
Select the speaker which is further from the microphone in
- <Adding aVoice Dialing Command> (page 46)
- <Setting a Voice Command for Category>
(page 46)
“Detailed Setup” Move to detailed item.
order to prevent howling or echoes.
“PIN Code Edit” Specify the PIN code required when registering
this unit using the Bluetooth device.
Refer to <Registering PIN Code> (page 44).
“Auto Answer” Answer a call automatically after lapse of the
preset time interval for automatic answer.
• “BT F/W Update” (Displaying the Firmware Version)
Display the version of the firmware of this unit.
For how to update the firmware, access our web site.
“OFF”/ “0SEC” – “8SEC” – “99SEC”
|
42 DPX-U6120/ DPX-U5120/ DPX-MP3120
Download from Www.Somanuals.com. All Manuals Search And Download.
Select”.
Registering Bluetooth device
2. Enter Special device registration mode
Press the [VOL] knob.
A list is displayed.
To make your Bluetooth device (cell-phone) usable
with this unit, you need to register it (pairing). You
can register up to 5 Bluetooth devices to this unit.
3. Select a device name
Turn the [VOL] knob and push the center when
the desired device name is displayed.
If “Completed” is displayed, registration is
completed.
4. Go through the procedure step 3 of
<Registering from this unit> (page 43) and
complete the registration (pairing).
Cancelling Special device registration mode
Press the [ ] button for at least 1 second.
Registering from this unit
1
Enter Bluetooth mode
Press the [LOG] button for at least 1 second.
2
Enter Bluetooth device registration mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Settings” > “PAIRING” > “Device
Registration”.
Search for the Bluetooth device.
When search is completed, “Finished” is displayed.
⁄
• If the device name is not in the list, select “Other Phones”.
3
4
Select a Bluetooth device
Turn the [VOL] knob and press it when the
desired item is displayed.
Input the PIN code
Operation type
Operation
Select the numbers.
Move to the next digit.
Delete the last digit.
Turn the [VOL] knob.
Press the [
Press the [
¢
] button.
] button.
4
5
Transmit the PIN code
Press the [VOL] knob.
If “Pairing Success” is displayed, registration is
completed.
✍ If the error message appears even though the
PIN code is correct, try <Registering Special
Bluetooth device> (page 43).
6
7
Return to the device list
Press the [ ] button.
Exit BT Settings mode
Press the [LOG] button for at least 1 second.
⁄
• This unit allows up to eight digits to be input for a PIN code.
If a PIN code cannot be input from this unit, it can be input
from the Bluetooth device.
• If there are 5 or more Bluetooth devices registered, you
cannot register a new Bluetooth device.
Registering Special Bluetooth device
Allow registration of a special device that cannot be
registered normally (pairing).
1. Select Special device registration mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Settings” > “PAIRING” > “Special Device
English
|
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Function of DPX-U6120 with KCA-BT200/BT300 (Optional Accessory)
Bluetooth Setup
Registering PIN Code
Selecting the Bluetooth device You
Wish to Connect
By operating the Bluetooth device, specify the PIN
code necessary for registering this unit.
When two or more Bluetooth devices have already
been registered, you need to select the Bluetooth
device you wish to use.
1
Enter Bluetooth mode
Press the [LOG] button for at least 1 second.
1
Enter Bluetooth mode
Press the [LOG] button for at least 1 second.
2
Enter PIN code edit mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Settings” > “Detailed Setup” > “PIN
Code Edit”.
2
Select Bluetooth device selection mode
Turn the [VOL] knob and press it when the
desired item is displayed.
The current setting of PIN code is displayed.
Cell-phone
3
Input the PIN code
Select “Settings” > “PAIRING” > “Phone
Selection”.
Operation type
Operation
Select the numbers.
Move to the next digit.
Delete the last digit.
Turn the [VOL] knob.
Audio player
Select “Settings” > “PAIRING” > “Audio
Selection”.
Press the [
Press the [
¢
] button.
] button.
4
3
Enter Bluetooth device selection mode
Press the [VOL] knob.
“(name)” is displayed.
4
5
Register a PIN code
Press the [VOL] knob.
If “Completed” is displayed, registration is
completed.
4
5
Select the Bluetooth device
Turn the [VOL] knob.
Exit BT Settings mode
Press the [LOG] button for at least 1 second.
Set up the Bluetooth device
Press the [VOL] knob.
“✱(name)” or “-(name)” is displayed.
“✱”: The selected Bluetooth device is busy.
“-”: The selected Bluetooth device is on standby.
“ “ (blank): The Bluetooth device is deselected.
⁄
• By default, “0000” is specified.
• A PIN code can be specified with up to eight digits.
6
Exit BT Settings mode
Press the [LOG] button for at least 1 second.
⁄
• If a Bluetooth device is already selected, deselect it, and
then select a different one.
• If you cannot select a device using the audio player,
connect the device with the audio player.
|
44 DPX-U6120/ DPX-U5120/ DPX-MP3120
Download from Www.Somanuals.com. All Manuals Search And Download.
Deleting a Registered Bluetooth
device
Downloading the Phone Book
Download the phone book data from the cell-
phone to this unit so that you can use the Phone
Book of this unit.
You can delete a registered Bluetooth device.
1
Enter Bluetooth mode
Press the [LOG] button for at least 1 second.
To download automatically
If the cell-phone supports a phone book
synchronization function, the phone book is
downloaded automatically after Bluetooth
connection.
2
Enter Bluetooth device deletion mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Settings” > “PAIRING” > “Device Delete”.
“(name)” is displayed.
⁄
• Setting on the cell-phone may be required.
• If no phone book data is found in the unit even after
the compete display, your cell-phone may not support
automatic download of phone book data. In this case, try
downloading manually.
3
Select the Bluetooth device
Turn the [VOL] knob.
4
5
Delete the selected Bluetooth device
Press the [VOL] knob.
To download from the cell-phone manually
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “YES”.
1
By operating the cell-phone, end the hands-free
connection.
“Completed” is displayed.
2
By operating the cell-phone, send the phone
book data to this unit
6
Exit BT Settings mode
Press the [LOG] button for at least 1 second.
By operating the cell-phone, download the phone
book data to this unit.
• During downloading:
⁄
• When a registered cell-phone is deleted, its Phone Book,
“Downloading”/ “Download..” is displayed.
• After completion of downloading:
“Completed” is displayed.
log, SMS, and voice tag are also deleted.
3
By operating the cell-phone, start the hands-
free connection.
To clear the downloading completion message
Press any button.
⁄
• Up to 1000 phone numbers can be registered for each
registered cell-phone.
• Up to 32 digits can be registered for each phone number
along with up to 50* characters representing a name.
(* 50: Number of alphabetic alphabetical characters.
Fewer characters can be input depending on the type of
characters.)
• To cancel downloading of the phone book data, operate
the cell-phone.
English
|
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Function of DPX-U6120 with KCA-BT200/BT300 (Optional Accessory)
Bluetooth Setup
Select“PB Name Check” (Play)
Press the [VOL] knob.
CompletedSelect“PB Name Delete” (Delete)
Adding a Voice Dialing Command
5
Add a voice tag to the phone book for voice dialing.
You can register up to 35 voice tags.
1
Enter Bluetooth mode
Press the [LOG] button for at least 1 second.
5
6
Delete a voice tag
Press the [VOL] knob.
2
Enter Phone book name edit mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Settings” > “Voice Tag” > “PB Name
Edit”.
Turn the [VOL] knob to select “YES”, and then
press the [VOL] knob.
Exit BT Settings mode
Press the [LOG] button for at least 1 second.
⁄
3
4
Search for the name to register
• Audio sound is not output during voice tag registration.
Select the name to register with reference to 4 in
<Calling a Number in the Phone Book> (page 21).
If a voice tag has already been registered for a
name, “*” is displayed before the name.
Setting a Voice Command for
Category
Add a voice tag to the phone number category
(type) for voice calling.
Select a mode
Turn the [VOL] knob.
Display
Operation
1
Enter Bluetooth mode
Press the [LOG] button for at least 1 second.
“PB Name Regist.”
“PB Name Check”*
“PB Name Delete”*
Register a voice tag.
Play a voice tag.
Delete a voice tag.
2
Enter Phone Number type edit mode
Turn the [VOL] knob and press it when the
desired item is displayed.
* Displayed only when a name for which a voice tag has
been registered is selected.
Select “Settings” > “Voice Tag” > “PN Type Edit”.
Select“PB Name Regist.” (Regist)
3
4
Select the category (type) you wish to set
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “General”, “Home”, “Office”, “Mobile”, or
“Other”
5
Register a voice tag (first)
“Enter Voice 1” is displayed.
When a beep is heard, say a voice tag within 2
seconds.
Select a mode
Turn the [VOL] knob.
6
Confirm the voice tag (second)
“Enter Voice 2” is displayed.
When a beep is heard, say the same voice tag as
that you said in step 6 within 2 seconds.
“Completed” is displayed.
Display
Operation
“PN Type Regist.”
“PN Type Check”*
“PN Type Delete”*
Register a voice tag.
Play a voice tag.
Delete a voice tag.
7
End registration
Press the [VOL] knob.
Return to step 2. You can register another voice tag
* Displayed only when a name for which a voice tag has
been registered is selected.
continuously.
5
6
Register the category (type) by performing
steps 5 to 7 in <Adding a Voice Dialing
Command> (page 46).
⁄
• If your voice cannot be recognized, a message is displayed.
Pressing the [VOL] knob allows you to retry voice input.
Exit BT Settings mode
Press the [LOG] button for at least 1 second.
⁄
• Set the voice tag for all the 5 categories. If the voice tag is
not registered for all the categories, the Phone book may
not be recalled by voice command.
|
46 DPX-U6120/ DPX-U5120/ DPX-MP3120
Download from Www.Somanuals.com. All Manuals Search And Download.
Function of DPX-U6120 with KCA-BT200/BT300 (Optional Accessory)
SMS (Short Message Service)
SMS (Short Message Service)
The SMS arrived at the cell-phone is displayed on
the receiver.
A newly arrived message is displayed.
¤
• To prevent car accidents, the driver should not read the
SMS while driving.
VOL
LOG
When a new message arrives
“SMS Received” is displayed.
The display disappears with any operations.
Downloading the SMS
Displaying the SMS
Download the short message (SMS) arrived at the
cell-phone so that it can be read on this unit.
1
2
Enter Bluetooth mode
Press the [LOG] button for at least 1 second.
✍ You can also select from “Settings” in Function
setting mode.
1
2
3
Enter Bluetooth mode
Press the [LOG] button for at least 1 second.
✍ You can also select from “Settings” in Function
setting mode.
Enter SMS Inbox mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “SMS Inbox”.
Enter SMS download mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Settings” > “SMS Download”.
A message list appears.
3
4
Select a message
Turn the [VOL] knob.
Each pressing of the [DISP] button switches
between telephone number or name and message
reception date.
Start downloading
Press the [VOL] knob.
“Downloading” is displayed.
When the downloading finishes, “Completed” is
displayed.
Display the text
Press the [VOL] knob.
Turning the [VOL] knob scrolls the message.
Pressing the [VOL] knob again returns to the
message list screen.
4
Exit BT Settings mode
Press the [LOG] button for at least 1 second.
⁄
• The cell-phone must be able to transmit the SMS using
Bluetooth. Setting on the cell-phone may be required. If
the cell-phone does not support SMS function, the SMS
download item in Function Control mode is not displayed.
• When the SMS is downloaded from the cell-phone, the
unopened messages in the cell-phone are opened.
• The already-read and unread short messages can be
respectively downloaded up to 75.
5
6
Exit SMS Inbox mode
Press the [ ] button.
Exit BT Settings mode
Press the [LOG] button for at least 1 second.
⁄
• The unopened message is displayed at the beginning of the
list. Other messages are displayed in the order of reception.
• The SMS that has arrived when the cell-phone is not linked
with Bluetooth cannot be displayed. Download the SMS.
• The short message cannot be displayed during
downloading the SMS.
English
|
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operations of remote control
In Tuner source
• Band select: [FM]/[AM]
• Station select: [4]/[¢]
• Recall preset stations: [1] — [6]
• Enter Menu List mode: [5]/[∞]
VOL
SRC
ATT
ENT
5/∞
In USB/Music CD/Audio file source
• Music select: [4]/[¢]
• Folder select: [FM]/[AM]
• Pause/Play: [ENT]
EXIT
AM
AUD
FM
• Enter Menu List mode: [5]
• Enter Music search mode: [∞]
• Movement between folders/files during Search
mode: [5]/[∞]
0 — 9
DIRECT
• Return to previous folder: [
]
In iPod source
• Music select: [4]/[¢]
• Pause/Play: [ENT]
General control
• Enter Menu List mode: [5]
• Volume control: [VOL]
• Source select: [SRC]
• Volume reduce: [ATT]
When the button is pressed again, the volume
returns to the previous level.
• Enter Music search mode: [∞]
• Movement between items during Music search
mode: [5]/[∞]
• Return to previous item: [
]
• Return to previous item: [
• Exit from mode: [EXIT]
• Selection of item: [5]/[∞]
• Determination: [ENT]
]
• Enter Audio Control mode: [AUD]
|
48 DPX-U6120/ DPX-U5120/ DPX-MP3120
Download from Www.Somanuals.com. All Manuals Search And Download.
Hands-free phone control
(DPX-U6120 only)
Preparing the remote control unit
Pull the battery sheet out from the remote control
unit to the direction of the arrow.
Making a call
• Enter Bluetooth mode: [
]
• Select a dialing method: [5]/[∞] ➜ [ENT]
• Number dial input:
Input a digit: [0] – [9]
Input “+”: [¢]
Input “#”: [FM]
Input “*”: [AM]
Clear the entered phone number: [4]
• Make a call: [DIRECT]
Changing the battery of the remote control
unit
Keep on slide
Receiving a call
• Answer the call: [
]
• Switch between the private talk mode and the
hands-free talk mode: [ENT]
CR2025
(+side)
Pull out
Call waiting
• Answer Another Incoming Call with the Current
Call Suspended: [
Use a commercially available button battery (CR2025).
Insert the battery with the + and – poles aligned
properly, following the illustration inside the case.
]
• Answer another Incoming Call after Terminating
the Current Call: [SRC]
• Continue the Current Call: [1]
During a call
• End the call: [SRC]
¤ CAUTION
• Do not set the remote control in hot places such
as on the dashboard.
• Lithium battery.
Danger of explosion if the battery is incorrectly
replaced.
Replace only with the same or equivalent type.
• The battery pack or batteries shall not be exposed
to excessive heat such sunshine, fire or the like.
• Keep battery out of reach of children and in
original package until ready to use. Dispose of
used batteries promptly. If swallowed contact
physician immediately.
English
|
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
About Audio file
About USB device
•
Playable Audio file
• When the USB device is connected to this unit,
it can be charged up provided that this unit is
powered.
AAC-LC (.m4a), MP3 (.mp3), WMA (.wma)
•
Playable disc media
• Install the USB device in the place where it will not
prevent you from driving your vehicle properly.
• You cannot connect a USB device via a USB hub and
Multi Card Reader.
• Save backups of the Audio files used with this unit.
The files can be erased depending on the operating
conditions of the USB device.
We shall have no compensation for any damage
arising out of erasure of the stored data.
• No USB device comes with this unit. You need to
purchase a commercially available USB device.
• When connecting the USB device, usage of the
CA-U1EX (option) is recommended.
• Normal playback is not guaranteed when a cable
other than the USB compatible cable is used.
Connecting a cable whose total length is longer
than 4 m can result in abnormal playback.
CD-R/RW/ROM
Playable disc file format
ISO 9660 Level 1/2, Joliet, Romeo, Long file name.
•
•
Playable USB device
USB mass storage class
Playable USB device file system
FAT16, FAT32
Even if the Audio files comply with the standards
listed above, the play may be impossible depending
on the types or conditions of media or device.
Playing order of the Audio file
In the example of folder/file tree shown below, the
files are played in the order from ① to ⑩.
•
^
¡
:
Folder
CD
(1)
:
A
udiofile
¡!
2
3
¡"
¡#
4
¡$
5
¡%
¡P
An online manual about Audio files is put on the site,
www.kenwood.com/cs/ce/audiofile/. On this online
manual, detailed information and notes which are not
written in this manual are provided. Make sure to read
through the online manual as well.
⁄
• In this manual, the word “USB device” is used for flash
memories and digital audio players which have USB
terminals.
|
50 DPX-U6120/ DPX-U5120/ DPX-MP3120
Download from Www.Somanuals.com. All Manuals Search And Download.
iPod/iPhone that can be connected to this
About “KENWOOD Music Editor”
• This unit supports the PC application “KENWOOD
Music Editor Light ver1.1” or later.
unit
Made for
• When you use the Audio file with database
information added by the “KENWOOD Music Editor
Light ver1.1”, you can search a file by title, album or
artist name using the <File Search> (page 13).
• iPod nano (6th generation) • iPod nano (5th generation)
• iPod nano (4th generation) • iPod nano (3rd generation)
• iPod nano (2nd generation) • iPod nano (1st generation)
• iPod with video
• iPod classic
• iPod touch (4th generation) • iPod touch (3rd generation)
• iPod touch (2nd generation) • iPod touch (1st generation)
• In the Instruction manual, the term “Music Editor
media” is used to mean the device that contains
Audio files with database information added with
KENWOOD Music Editor.
• iPhone 4
• iPhone 3GS
• iPhone
• iPhone 3G
• “KENWOOD Music Editor Light ver1.1” is available
from the following web site:
• For further information on “KENWOOD Music
Editor Light ver1.1”, refer to the site above or the
application help.
• For information on the compatibility of iPod/iPhone
• Type of control available varies depending
on the type of connected iPod. See
www.kenwood.com/cs/ce/ipod/ for further details.
• The word “iPod” appearing in this manual indicates
the iPod or the iPhone connected with the iPod
connection cable* (optional accessory).
* Not supported model KCA-iP500.
• Refer to the web site for connectable iPod and iPod
connection cable.
⁄
• If you start playback after connecting the iPod, the music
that has been played by the iPod is played first.
In this case, “RESUMING” is displayed without displaying a
folder name, etc. Changing the browse item will display a
correct title, etc.
• You cannot operate iPod if “KENWOOD” or “✓” displayed on
iPod.
English
|
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories/ Before installation
system, connect the connectors either to both the front
output terminals or to both the rear output terminals (do
not mix front and rear). For example, if you connect the +
connector of the left speaker to a front output terminal, do
not connect the - connector to a rear output terminal.
• Connect the speaker wires correctly to the terminals to
which they correspond. The unit may be damaged or fail to
work if you share the - wires or ground them to any metal
part in the car.
Installation accessories
1
..........1
2
• Do not use your own screws. Use only the screws provided.
If you use the wrong screws, you could damage the unit.
• If your car’s ignition does not have an ACC position, connect
the ignition wires to a power source that can be turned on
and off with the ignition key. If you connect the ignition
wire to a power source with a constant voltage supply, as
with battery wires, the battery may die.
..........1
3
• If the console has a lid, make sure to install the unit so that
the faceplate will not hit the lid when closing and opening.
• After the unit is installed, check whether the brake lamps,
blinkers, wipers, etc. on the car are working properly.
• Mount the unit so that the mounting angle is 30° or less.
..........6
4
..........6
Before installation
2 WARNING
• The unit can only be installed in a car with a 12V DC
power supply, negative ground.
• If you connect the ignition wire (red) and the
battery wire (yellow) to the car chassis (ground),
you may cause a short circuit, that in turn may start
a fire. Always connect those wires to the power
source running through the fuse box.
¤
CAUTION
• Install this unit in the console of your vehicle.
• Do not touch the metal part of this unit during and shortly
after the use of the unit. Metal part such as the heat sink
and enclosure become hot.
• Mounting and wiring this product requires skills and
experience. For safety’s sake, leave the mounting and wiring
work to professionals.
• If you experience problems during installation, consult your
Kenwood dealer.Disconnect the battery’s negative terminal
and make all electrical connections before installing the
unit.
• Insulate unconnected wires with vinyl tape or other similar
materials. To prevent a short circuit, do not remove the caps
on the ends of the unconnected wires or the terminals.
• Be sure to ground this unit to the car’s chassis again after
installation.
• If the fuse blows, first make sure the wires are not touching
to cause a short circuit, then replace the old fuse with one
with the same rating.
• When only two speakers are being connected to the
|
52 DPX-U6120/ DPX-U5120/ DPX-MP3120
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Wires to Terminals
Fuse (10A)
Antenna Cord
FM/AM antenna input (JASO)
Front output (DPX-U6120/ DPX-U5120 only)
Rear output/ Sub Woofer output
To Kenwood disc changer/External optional accessory
(DPX-U6120 only)
Wiring harness
(Accessory 1)
To connect these leads, refer to the relevant instruction
⁄
manuals.
White
To front left speaker
White/Black
Gray
Gray/Black
Green
To front right speaker
To rear left speaker
To rear right speaker
Green/Black
Purple
Purple/Black
If no connections are made, do not let the wire come out from the tab.
Blue/White (Power control wire)
Blue (Antenna control wire)
When using the optional power amplifier, connect to its power
control terminal.
P.CONT
Depending on what antenna you are using, connect either to
the control terminal of the motor antenna, or to the power
terminal for the booster amplifier of the film-type or short pole
type antenna.
ANT.
CONT
Brown (Mute control wire)
Connect to the terminal that is grounded when either the
telephone rings or during conversation.
MUTE
To connect the Kenwood navigation system, consult your
⁄
navigation manual.
Orange/ White (Dimmer control wire)
To car light control switch
ILLUMI
Light Blue/ Yellow (Steering
remote control wire)
To use the steering wheel remote control feature, an exclusive
remote adapter (not supplied) that matches your car is required.
REMOTECONT
STEERING WHEEL
REMOTEINPUT
Ignition key
switch
Car fuse
box
ACC
Red (Ignition wire)
Yellow (Battery wire)
Car fuse box
(Main fuse)
Black (Ground wire) · (To car chassis)
+
–
Battery
English
|
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Installation
Install onto the car bracket using the supplied screws
(M5 × 6 mm, M5 × 7 mm). The holes of the car
bracket to use will differ depending on the car model.
Car Bracket
Accessory3 (M5 × 7 mm)
or Accessory4(M5 × 6 mm)
Accessory2
(Only for NISSAN car)
|
54 DPX-U6120/ DPX-U5120/ DPX-MP3120
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Guide
Some functions of this unit may be disabled by
some settings made on this unit.
What might seem to be a malfunction in your unit
may just be the result of slight misoperation or
miswiring. Before calling service, first check the
following table for possible problems.
!
• Cannot set up the subwoofer.
• No output from the subwoofer.
• Cannot set up the subwoofer position of Manual
position setting.
General
? The operation check sound (beep sound) does not
• The Dual zone function is enabled. <Dual Zone
System> (page 35)
• “SubWoofer” of <Audio Control> (page 32)/
“SUBWOOFER SET” of <Audio Control> (page 36) is
not set to ON.
sound.
✔
The preout jack is being used.
The Touch Sensor Tone cannot be output from
the preout jack.
? The illumination flashes when the knob or button
is operated.
• “SubWoofer” >“FC” of <X’Over Setting> (page 38))/
“LPF SUBWOOFER” of <Audio Control> (page 36) is
set to “Through”/ “THROUGH”.
• In the speaker select option, None is selected for
the subwoofer. <Speaker Setting> (page 37)
✔
This is the key illumination effect.
You set this effect in “ILLUMI Effect” of <Display
Setting> (page 24).
? The key illumination effect brought about in
conjunction with the sound volume is small.
!
!
• Cannot set up the equalizer.
• Cannot set up the Bass Boost.
• Cannot set up the Highway sound.
• Cannot set up the Supreme.
• Cannot set up the Position control.
• The Dual zone function is enabled. <Dual Zone
System> (page 35)
• The DSP function is disabled. “DSP Set” of <Audio
Control> (page 32)
• In the speaker select option, None is selected for
the rear speakers. <Speaker Setting> (page 37)
✔
The key illumination effect may be insufficient
depending on the sound volume and sound quality.
Tuner source
? Radio reception is poor.
✔
The car antenna is not extended.
Connect the Antenna control wire to the power
terminal for the booster amplifier of the film-type
or short pole type antenna
Pull the antenna out all the way.
• Cannot select the output destination of the
subsource in the Dual zone.
Disc source
• Cannot adjust the volume of the rear speakers.
The Dual zone function is disabled. <Dual Zone
System> (page 35)
? The specified disc does not play, but another one
plays instead.
✔
✔
The specified CD is quite dirty.
Clean the CD, referring to the CD cleaning of the
section on <Handling discs> (page 4).
!
!
!
Cannot set up Display.
<Demonstration mode Setting> (page 31) is not
turned off.
The disc is loaded in a different slot from that
specified.
Eject the disc magazine and check the number
for the specified disc.
Cannot switch to USB/iPod source.
The Dual zone function is set to USB/iPod. <Dual
Zone System> (page 35)
✔
The disc is severely scratched.
Try another disc instead.
Audio file source
The number of songs contained in “SONGS”
category of this unit is different from that
contained in “SONGS” category of iPod.
Podcast files are not counted in this unit as this unit
does not support the playback of podcast files.
? The sound skips when an Audio file is being
played.
✔
✔
The media is scratched or dirty.
Clean the media, referring to the CD cleaning of
the section on <Handling discs> (page 4).
The recording condition is bad.
Record the media again or use another media.
English
|
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Guide
Hands-free
The messages shown below display your
systems condition.
? The hands-free talk volume is low.
✔
The hands-free talk volume is set at a low level.
TOC Error/TOC ERROR:
The hands-free talk volume can be adjusted
independently. Adjust it during hands-free talk.
“Mic Gain” and “NR Level” <Bluetooth Setting>
(page 42).
• No disc has been loaded in the disc
magazine.
• The CD is quite dirty. The CD is upside-
down. The CD is scratched a lot.
? No sound is heard from the rear speakers.
You are talking in the hand-free talk mode.
Error 05/ERROR 05:
✔
The disc is unreadable.
No sound is heard from the rear speakers in the
hands-free talk mode.
Mecha Error/Mecha ERR/Error 77/ERROR 99/ERROR 77:
The unit is malfunctioning for some reason.
Press the reset button on the unit. If the
“Mecha Error”/ “Mecha ERR”/ “Error 77”/
“ERROR 99”/ “ERROR 77”code does not
disappear, consult your nearest service
center.
? No beep is heard at reception of an incoming call.
✔
No beep is heard depending on the type of your
cell-phone.
The“Call Beep”of <Bluetooth Setting> (page 42) is
set ON.
? Voice is not recognized.
CD (Blink):
The CD player section is not operating
properly.
✔
✔
✔
The vehicle window is open.
If the surrounding noise is large, voice cannot be
recognized properly. Close the vehicle windows
to reduce noise.
Reinsert the CD. If the CD cannot be
ejected or the display continues to flash
even when the CD has been properly
reinserted, please switch off the power
and consult your nearest service center.
Small voice.
If voice is too small, it cannot be recognized
properly. Speak into the microphone a little more
loudly and naturally.
The person uttering the voice tag is not the one who
registered the it.
Protect/PROTECT (Blink):
The speaker wire has a short-circuit or
touches the chassis of the vehicle, and then
the protection function is activated.
Wire or insulate the speaker cable properly
and press the reset button. If the “Protect”
code does not disappear, consult your
nearest service center.
Only the voice of the person who registered the
voice tag can be recognized.
Bluetooth audio source
Unsupported File/NA FILE:
? The Bluetooth audio player cannot be registered
An Audio file is played with a format that this
unit can’t support.
(pairing).
✔
The PIN code is fixed.
When a PIN code is specified in the Instruction
Manual for Bluetooth Audio Player, register it
with reference to <Registering PIN Code> (page
44) to register the Bluetooth audio player. If no PIN
code is specified in the Instruction Manual, try
“0000”.
Copy Protection/COPY PRO:
A copy-protected file is played.
Read Error/READ ERROR:
The file system of the connected USB device
is broken.
Copy the files and folders for the USB
device again. If the error message is still
displayed, initialize the USB device or use
other USB devices.
? The sound from the Bluetooth audio player is
discontinuous.
✔
The distance between this unit and audio player is
too far.
No Device/NO DEVICE:
Move the audio player nearer to this unit.
The USB device is selected as a source
although no USB device is connected.
Change the source to any source other
than USB. Connect an USB device, and
change the source to USB again.
✔
Another Bluetooth device is affecting the Bluetooth
communication.
Turn off another Bluetooth device.
Move another Bluetooth device away from this
unit.
✔
Another Bluetooth device or profile is used for
communication.
The downloading of the Phone book or the SMS
disconnects the sound.
|
56 DPX-U6120/ DPX-U5120/ DPX-MP3120
Download from Www.Somanuals.com. All Manuals Search And Download.
N/A Device/NA DEVICE:
• An unsupported USB device is connected.
Err No Matching:
The voice tag is wrong. Voice cannot be
recognized because of an unregistered voice
tag, etc.
• Connection to the iPod has failed.
Remove the USB device and then
reconnect it.
Check that the connected iPod is an iPod
that is supported. See <About Audio file>
(page 50) for information on supported
iPods.
Too Soft:
Too Loud:
Too Long:
Voice is too small and cannot be recognized.
Voice is too large to be recognized.
The word or utterance is too long to be
recognized.
Reset iPod/ iPhone.
No Music Data/Error 15/No Music/NO MUSIC/EROOR 15:
• The connected USB device contains no
playable Audio file.
No Phonebook: Data is not contained in the phone book.
No Message: No short message in In Box.
• Media was played that does not have data
recorded that the unit can play.
No Record:
The voice tag is not registered in the phone
book.
USB Error/USB ERROR:
Memory Full: The number of voice tags reaches the
maximum number to be registered in the
phone book.
Some trouble may have occurred to the
connected USB device.
Remove the USB device, then cycle the
power switch to ON. If the same display is
repeated, use another USB device.
No Voice:
No call.
iPod Error/iPod ERROR:
Connection to the iPod has failed.
Remove the USB device and then
reconnect it.
Reset iPod/ iPhone.
No Number:
No Data:
• The calling party does not notify a caller ID.
• There is no phone number data.
• There is no outgoing call list.
• There is no incoming call list.
• There is no missed call list.
• There is no phone book list.
No Entry:
The cell-phone has not been registered
(pairing).
HF Disconnect/HF D-CON:
The unit cannot communicate with the cell-
phone.
HF Error 07:
The memory cannot be accessed.
Turn off the power and on again. If this
message still appears, press the reset
button on the control unit.
HF Error 68:
The unit cannot communicate with the cell-
phone.
Turn off the power and on again. If this
message still appears, press the reset
button on the control unit.
Unknown:
The Bluetooth device cannot be detected.
Device Full:
5 Bluetooth device have already been
registered. No more Bluetooth device cannot
be registered.
PIN Code NG: The PIN code is wrong.
Connect NG: The unit cannot be connected to the device.
Pairing Failed: Pairing error.
English
|
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
FM tuner section
USB Interface (DPX-U6120/ DPX-U5120)
Frequency range
200 kHz step : 87.9 MHz – 107.9 MHz
USB Standard
: USB1.1/ 2.0 (Full speed)
50 kHz step : 87.5 MHz – 108.0 MHz
Usable sensitivity (S/N = 26dB)
DPX-U6120: 8.1 dBf (0.7 μV/75 Ω)
DPX-U5120/ DPX-MP3120: 11.2 dBf (1 μV/75 Ω)
Quieting Sensitivity (S/N = 50dB)
DPX-U6120: 15.3 dBf (1.6 μV/75 Ω)
DPX-U5120/ DPX-MP3120: 19.2 dBf (2.5 μV/75 Ω)
Frequency response ( 3 dB)
: 30 Hz – 15 kHz
Signal to Noise ratio (MONO)
DPX-U6120: 65 dB
DPX-U5120/ DPX-MP3120: 63 dB
Maximum Supply current
: 500 mA
File System
: FAT16/ 32
MP3 decode
: Compliant with MPEG-1/2 Audio Layer-3
WMA decode
: Compliant with Windows Media Audio
AAC decode
: AAC-LC ”.m4a” files
Audio section
Stereo separation (1 kHz)
: 40 dB
Maximum output power
: 50 W x 4
Full Bandwidth Power (at less than 1% THD)
: 22 W x 4
AM tuner section
Frequency range
10 kHz step : 530 kHz – 1700 kHz
9 kHz step : 531 kHz – 1611 kHz
Usable sensitivity (S/N = 20dB)
DPX-U6120: 28 dBµ (25 µV)
Speaker Impedance
: 4 – 8 Ω
Tone action
DPX-U6120
BAND1 (60 Hz): 9 dB
BAND2 (250 Hz): 9 dB
BAND3 (1 kHz): 9 dB
BAND4 (4 kHz): 9 dB
BAND5 (16 kHz): 9 dB
DPX-U5120/ DPX-MP3120
Bass : 100 Hz 8 dB
Middle : 1 kHz 8 dB
Treble : 12.5 kHz 8 dB
Preout level / Load (CD)
DPX-U6120: 2500 mV/10 kΩ
DPX-U5120/ DPX-MP3120: 31 dBµ (36 µV)
CD player section
Laser diode
: GaAlAs
Digital filter (D/A)
: 8 Times Over Sampling
D/A Converter
: 24 Bit
Spindle speed
: 500 – 200 rpm (CLV)
Wow & Flutter
: Below Measurable Limit
DPX-U5120/ DPX-MP3120: 2000 mV/10 kΩ
Preout impedance
: ≤ 600 Ω
Frequency response ( 1 dB)
: 10 Hz – 20 kHz
Auxiliary input
Total harmonic distortion (1 kHz)
: 0.008 %
Signal to Noise ratio (1 kHz)
: 105 dB
Dynamic range
: 93 dB
MP3 decode
: Compliant with MPEG-1/2 Audio Layer-3
WMA decode
: Compliant with Windows Media Audio
AAC decode
: AAC-LC “.m4a” files
Frequency response ( 1 dB)
: 20 Hz – 20 kHz
Input Maximum Voltage
: 1200 mV
Input Impedance
: 10 kΩ
General
Operating voltage (11 – 16V allowable)
: 14.4 V
Maximum Current consumption
: 10 A
Installation Size (W x H x D)
: 182 x 111 x 158 mm
Weight
: 1.5 kg
Specifications subject to change without notice.
|
58 DPX-U6120/ DPX-U5120/ DPX-MP3120
Download from Www.Somanuals.com. All Manuals Search And Download.
The marking of products using lasers
CLASS 1
LASER PRODUCT
The label is attached to the chassis/case and says that the component
uses laser beams that have been classified as Class 1. It means that the
unit is utilizing laser beams that are of a weaker class. There is no danger
of hazardous radiation outside the unit.
This symbol mark indicates that Kenwood
manufactured this product so as to
decrease harmful influence on the
environment.
• The Bluetooth word mark and logos are owned by
the Bluetooth SIG, Inc. and any use of such marks
by Kenwood Corporation is under license. Other
trademarks and trade names are those of their
respective owners.
• The “AAC” logo is a trademark of Dolby Laboratories.
• iTunes is a trademark of Apple Inc.
• “Made for iPod” and “Made for iPhone” mean that an
electronic accessory has been designed to connect
specifically to iPod or iPhone, respectively, and has
been certified by the developer to meet Apple
performance standards. Apple is not responsible for
the operation of this device or its compliance with
safety and regulatory standards. Please note that the
use of this accessory with iPod or iPhone may affect
wireless performance.
• iPhone, iPod, iPod classic, iPod nano, and iPod touch
are trademarks of Apple Inc., registered in the U.S. and
other countries.
• “Adobe Reader” is a trademark of Adobe Systems
Incorporated.
English
|
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|